InFocus IN5108 User Guide
IN5110 User’s Guide
5100
Downloaded from ProjectorsManual.com Manuals
QR80421
Regulatory models: W59
Declaration of Conformity
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interferences received,
including interference that may cause undesired operation.
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland,
Oregon 97223 USA
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
We declare under our sole responsibility that this projector conform to the following
directives and norms:
EMC Directive 2004/108/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
EN EMC directive
Safety: IEC 60950-1: 1st Edition
This product may cause interference if used in residential areas. Such use must be
avoided unless the user takes special measures to reduce electromagnetic emissions
to prevent interference to the reception of radio and television broadcasts.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. HDMI, the HDMI logo and
High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC. InFocus, In Focus, and INFOCUS (stylized) are either
registered trademarks or trademarks of InFocus Corporation in the United States and
other countries.
Canada
FCC Warning
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL
Other specific Country Approvals may apply, please see product certification label.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense. This device complies with part 15 of the FCC Rules.
This document applies to model W59.
Input ratings: 100-120/220-240Vac, 5.0/2.1A, 50/60Hz
Remote Control Warning
Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote
control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of IEC60825-1:1993 +A1:1997
+A2: 2001 or IEC60825-1:2007 EN60825-1:2007.
Downloaded from ProjectorsManual.com Manuals
1
WARNING: Do not look into laser beam emitted from the front of the
remote control.
CAUTION: Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure. Class 2 Laser product; maximum output 1mW; wavelength
650nm.
[Class 2 Laser Product] Wavelength 650nm; Maximum output 1mW; No
beam divergence.
IEC60825-1:2007 EN60825-1:2007
[Laser Diode] Wave length 650nm; Maximum power 7mW; Beam divergence 33deg (perpendicular)/8deg (parallel).
OR
IEC60825-1:1993 +A1:1997 +A2:2001
Location of laser beam warning labels on remote
Downloaded from ProjectorsManual.com Manuals
2
For complete details on connecting and operating the projector, refer to this
User’s Guide.
The website also has technical specifications (an interactive image size calculator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration.
Table of Contents
Introduction
Included Items
Positioning the projector
Connecting a computer
Required computer connections
Displaying a computer image
Adjusting the image
Connecting a video device
Displaying a video image
Shutting down the projector
Troubleshooting your setup
5
5
7
8
8
10
11
12
13
15
15
Using the keypad buttons
Using the remote control
Using the audio
22
23
24
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
25
25
26
26
Using the menus
Picture menu
Settings menu
27
28
33
Maintenance
Cleaning the lens
Replacing the projection lamp
Cleaning the dust filter
Using the security lock
37
37
38
40
40
Appendix
41
41
42
Projected image size
Command Control
Downloaded from ProjectorsManual.com Manuals
3
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
Use only approved ceiling mounts.
•
Warning: To prevent eye injury if the projector is ceiling mounted,
1
Place the projector in a horizontal position no greater than 8 degrees off
axis.
2’ / 0.
8’ / 2
.4 m
wear protective eyewear before opening lamp door. A warning sticker
is included with the user documentation. Place this sticker on the lamp
door if the projector is mounted on the ceiling.
•
Only genuine InFocus lamps are tested for use in this projector. InFocus is not liable for the performance, safety or certification of any other
lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector.
•
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this manual for proper startup and shutdown procedures.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. When the projector is turned on, keep people, food,
and drinks out of the "keep out" area under and around the projector,
as indicated by the "X" areas.
5’
m
.5
/1
6m
3’
/
•
m
Important Operating Considerations for Safety
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty booklet.
Downloaded from ProjectorsManual.com Manuals
4
Introduction
Projector components and features: front
Your new multimedia projector provides three computer, three video, and
four audio inputs, one audio output, and RS-232 and Network control. It
has WUXGA 1920 x 1200 resolution. The projector is easy to connect, easy to
use, and easy to maintain.
zoom/offset door
remote
control
receiver
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website. Web address information is located on the back inside
cover of this User’s Guide.
air intake
vent
heat vent
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the web address.
elevator foot release
focus
Included Items
leveling foot
Projector components and features: back
lamp door
projector
remote
lens cap*
power cable
VGA computer cable
A/V cable
documentation
*The lens cap is tethered to the projector.
connectors
Downloaded from ProjectorsManual.com Manuals
5
power switch
power plug
Connector Panel
The projector provides three computer and three video connection options:
•
one VGA computer
•
one HDMI™ (High Definition Multimedia Interface)*
•
one component BNC (G/Y, B/CB/PB, R/CR/PR, H, V)
•
one component RCA video (Pr, Pb, Y)
•
one S-video
•
one composite RCA video
HDMI
component video
remote USB
BNC
control
VGA computer
RJ-45 receiver
monitor
(IR)
audio in 1,2
lock
RS232
serial control
The projector provides computer and video connectors for audio support:
•
two composite RCA stereo audio (L, R)
•
one audio out
•
two audio ins
s-video
speaker
The projector also provides the following connectors:
•
one wired remote
•
one monitor out
•
RS-232 serial connector (for serial control)
•
RJ-45 connector (for networked control)
The RS-232 Command Line Interface (CLI) specifications and commands
are available in the Appendix and on our website, www.infocus.com/support.
* HDMI is an industry standard, uncompressed, all-digital audio/video
interface that connects between sources, such as set-top boxes, DVD players, and receivers and your projector. To take advantage of HDMI 1.3 you
must have a 1.3-compatible source. The HDMI, because it is a digital signal,
yields the highest quality image. It is common for these signals to be
encrypted with HDCP (high-bandwidth digital-content protection). Your
new projector ships standard with decryption codes so you can enjoy these
high quality, all digital images.
Downloaded from ProjectorsManual.com Manuals
6
composite
power connector and switch
video audio in 3,4 external
speakers wired remote
(audio out)
Positioning the projector
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guidelines:
10’ high image
Projection angle in 16:10 mode (default)
10:0
1:1
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 3 feet (0.9m) from the projection screen.
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
10:0
bottom of image
at lens center
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 33. We recommend
using an authorized ceiling mount. The Ceiling Mount Kit is sold separately; visit our website for more information.
1:1
bottom of image
50% below
lens center
•
Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image. For information about image sizes at different distances, see “Projected image
size” on page 41.
•
For the standard lens that comes with the projector, the image exits at a
given angle. However, the lens shift feature makes the image offset
variable. The image offset is 100% at a 10:1 ratio when the projector is in
16:10 mode (default mode). This means that if you have an image 10’
high, the bottom of the image will be at the center of the lens.
•
The image offset is 50% when the lens shift is at a 1:1 ratio. This means
that if you have an image 10’ high, the bottom of the image will be 5’
below the center of the lens.
lens center
Downloaded from ProjectorsManual.com Manuals
7
Connecting a computer
connect computer cable
Required computer connections
Connect one end of the VGA computer cable to the Computer 2 connector
on the projector. Connect the other end to the video port on your computer.
If you are using a desktop computer, you first need to disconnect the monitor cable from the computer’s video port.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
You can also connect to your computer using optional BNC or HDMI
cables. Connect the BNC connectors on the BNC cable to the appropriate
Computer 3 connectors on the projector. Connect the other end to the video
port on your computer. If you are using a desktop computer, you first need
to disconnect the monitor cable from the computer’s video port.
Or, connect the HDMI cable to the Computer 1 connector.
connect BNC cable
To have sound with your presentation, connect the audio cable to your
computer and to the corresponding computer Audio In connector on the projector. You can assign a particular source to a particular audio in connector,
see page 33.
connect audio cable
Downloaded from ProjectorsManual.com Manuals
8
connect HDMI cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the Monitor out connector on the projector.
connect monitor cable
You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the projector’s Serial Control connector. Specific RS-232 commands can be found in
the Service and Support section of our website and in the Appendix.
connect RS-232 cable
The projector can be managed by networking software through its Network
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
connect CAT-5 cable
Network
Downloaded from ProjectorsManual.com Manuals
9
Displaying a computer image
remove lens cap
Remove the lens cap.
Press the power switch on the back of the projector to the on (I) position.
The Power light on the Status Indicator Panel (page 15) lights green.
press Power switch
press Power button
I
O
2
Press the Power button on the top of the projector or the remote.
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
? No startup screen? Get help on page 16.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the keypad or remote.
activate laptop’s external port
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documentation to learn your computer’s key combination.
? No computer image? Get help on page 16.
Downloaded from ProjectorsManual.com Manuals
10
Adjusting the image
adjust height
Adjust the height of the projector, if necessary, by pressing the release buttons on each side of the projector’s front to extend the elevator feet.
release
button
release
button
elevator
foot
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle (perpendicular) to the screen.
adjust distance
See page 41 for a table listing screen sizes and distances.
Adjust the zoom by rotating the Zoom ring inside the lens door until the
desired image size is produced.
adjust zoom and focus
Adjust the focus by rotating the Focus ring on the lens until the desired
focus is produced.
adjust lens shift
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
adjust Contrast or Brightness
contrast
brightness
Adjust the Contrast or Brightness in the Picture menu.
See page 27 for help with the menus.
Downloaded from ProjectorsManual.com Manuals
11
Connecting a video device
connect A/V cable
Standard video connections
Plug the audio/video (A/V) cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the yellow Video 3 connector on the projector. Plug a white connector into the left
audio out connector on the video device and plug a red connector into the
right audio out connector on the video device. Plug the remaining white
connector into a left audio in connector on the projector, and plug the red
connector into a right audio in connector on the projector. You can assign a
particular source to a particular audio in connector, see page 33.
connect power cable
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
NOTE: Always use the power cable that shipped with the projector.
Optional video connections
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the Video 2 connector on the projector. Use the A/V cable’s
audio connectors as described directly above (the yellow connectors on the
A/V cable are not used).
If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
video device and into the Video 1 green component connector (labeled “Y”)
on the projector. Plug the component cable’s blue connectors into the blue
component-out connector on the video device and into the blue component
connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s
red connectors into the red component-out connector on the video device
and into the red component connector (labeled “Cr/Pr”) on the projector.
Use the A/V cable’s audio connectors as described above (the yellow connectors on the A/V cable are not used). NOTE: The component connectors
can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).
connect S-video and video cables
connect component cables
and video cables
Downloaded from ProjectorsManual.com Manuals
12
Displaying a video image
remove lens cap
Remove the lens cap.
Press the power switch on the back of the projector to the on (I) position.
The Power light on the Status Indicator Panel (page 15) lights green.
I
press Power button
2
O
press Power switch
Press the Power button on the top of the projector or the remote.
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
? No startup screen? Get help on page 16.
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Source button on the keypad or remote.
adjust height
Adjust the height of the projector, if necessary, by pressing the release buttons on each side of the projector’s front to extend the elevator feet. Rotate
the feet, if necessary, to level the projector.
release
button
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 41 for a table listing screen sizes and distances
to the screen.
Downloaded from ProjectorsManual.com Manuals
13
release
button
elevator
foot
Adjust the zoom by rotating the Zoom ring, located inside the lens door,
until the desired image size is produced.
adjust Zoom and Focus
Adjust the focus by rotating the Focus ring on the lens until the desired
focus is produced.
adjust Lens Shift
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
adjust volume
Adjust the volume in the Audio menu.
adjust Picture menu
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
See page 27 for help with the menus.
Downloaded from ProjectorsManual.com Manuals
14
Shutting down the projector
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
The projector automatically blanks the screen after no active source is
detected for 5 minutes. This blank screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save
Table 1: Status indicator light behavior and meaning
You can make the blank screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 34.
Status Indicator Panel icons
Meaning
Power Save
Power, solid green
The power button has been pressed and
the software has initialized or the projector has been powered off.
Power, blinking green
The power button has been pressed and
the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 20). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Lamp
Turn off the projector and wait one minute, then turn the projector on again. If
the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one minute, then turn the projector on again. If
the service lamp turns on again, service is
required. Visit our website to contact Service.
The projector also has a Power Save feature that automatically turns the
lamp off after no signals are detected for 20 minutes. After 10 additional
minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 34.
Turning off the projector
To turn off the projector, press the power button and verify that you want to
turn the projector off by pressing the power button again within 3 seconds.
You can cancel the shutdown by not pressing the power button a second
time. The lamp turns off and the Power light blinks green for over 1 minute
while the fans continue to run to cool the lamp. When the lamp has cooled,
the Power light is solid green and the fans stop. Press the power switch on
the back of the projector and unplug the power cable to completely power
off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Downloaded from ProjectorsManual.com Manuals
15
Problem
Solution
Result
No startup screen
Plug power cable in, press power switch and
power button. Remove lens cap.
Correct image
3
2
startup
screen
1
Computer image projected
Only startup screen appears/no computer image
Press the Source button
Activate laptop’s external port
A
startup
screen
A
or restart
laptop
Downloaded from ProjectorsManual.com Manuals
16
A
Computer image projected
No computer image, just the words “Signal out of range”
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating system)
Signal out of
range
A
A
A
You may also need to set a different
resolution on your computer, as shown
in the following problem, “Image fuzzy
or cropped”
Image clear and not cropped
Image fuzzy or cropped
A
A
Set your computer’s display resolution to the
native resolution of the projector
(Start>Settings>Control Panel>Display>Settings
tab, select1920x1200)
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
Downloaded from ProjectorsManual.com Manuals
17
A
Projector troubleshooting
Problem
Solution
Result
Image not square
Adjust keystone in the Picture menu
Square image
Image not sharp
Adjust the focus ring or Sharpness in the
Picture>Advanced menu
Correct image
AB
AB
Image does not fit 16:9 screen
Change aspect ratio to 16:9 in Picture>Aspect
ratio menu
Downloaded from ProjectorsManual.com Manuals
18
Correct image
Turn on/off Ceiling in Settings>System menu
Image upside down
Correct image
BA
Image reversed left to right
AB
Turn on/off Rear in Settings>System menu
Correct image
A
Projected colors don’t match source
AB
Adjust color, tint, color temperature, brightness,
contrast in the menus
COLOR
Correct image
COLOR
Downloaded from ProjectorsManual.com Manuals
19
Lamp won’t turn on, Temp light is lit (page 15)
Make sure vents aren’t blocked; allow projector
to cool for one minute
Unplug projector; wait 20 minutes; plug in
projector and turn it on: lamp lights
Temperature light
Lamp won’t turn on, Lamp light is lit (page 15)
startup
screen
Lamp may need to be replaced (page 38)
Lamp light
Lamp turns on
startup
screen
Downloaded from ProjectorsManual.com Manuals
20
Image not centered on screen
Move projector, adjust zoom or lens shift, adjust
height
Correct image
Adjust horizontal or vertical position in
Picture>Advanced menu
Still having problems?
If you need assistance, visit our website (www.infocus.com/service) or call us.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its
full value.
Downloaded from ProjectorsManual.com Manuals
21
Using the keypad buttons
power–turns the projector on (page 10) and off (page 15).
menu–opens the on-screen menus (page 27).
up/down arrows–navigates to and adjusts settings in the menus (page 27).
select–confirms choices made in the menus (page 27).
source–switches among active sources
Downloaded from ProjectorsManual.com Manuals
22
Using the remote control
LED
navigation buttons
The remote uses two (2) AAA batteries (not included). They are easily
installed by sliding the cover off the remote's back, aligning the + and - ends
of the batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 16 feet (5m). For
best results, aim the remote directly at the projector.
source buttons
To use the laser pointer, press and hold the Laser button. The laser turns off
when the button is released, or times out after two (2) minutes of continuous operation.
laser
button
backlight button
WARNING: Do not look into the laser beam emitted from the top of the
remote control.
The remote contains four Source buttons that allow you to assign a particular input to a specific source. Simply press the numbered Source buttons to
travel to whatever four sources you wish to have available.
Troubleshooting the remote
Press the remote's Menu button to open the projector's menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
values in the menus.
•
Make sure the batteries are installed in the proper orientation and are
not dead. The LED at the top of the remote lights when any button is
pressed when the battery power is adequate.
The remote also has a power button to turn the projector on and off, volume
buttons and a mute button to control the sound, a backlight button to light
the remote's buttons in the dark, and a video and computer button to switch
between those two sources.
•
Make sure you’re pointing the remote at the projector, not the computer, and are within the remote range of 16 feet (5m).
Two presentation-specific features are also provided. Use the blank button
to display a blank screen instead of the current slide; use the effect button to
invoke a user-definable action, such as freeze, or magnify.
The Auto Image button reacquires the computer image and the Presets button lets you customize the settings for each source. Up to three Preset settings can be customized and saved.
Downloaded from ProjectorsManual.com Manuals
23
Using the audio
connect audio cable
To play sound from the projector, connect your source to an Audio In connector on the projector.
To adjust the volume, mute, or loudness, use the Audio menu (see page 33).
Troubleshooting audio
If there is no sound, check the following:
•
Make sure the audio cable is connected.
•
Make sure mute isn’t active.
•
Make sure the volume is turned up enough.
•
Make sure you are connected to the corresponding audio in for your
source. By default, Audio 1 corresponds to Computer 2, Audio 2 corresponds to Computer 3, Audio 3 corresponds to Video 2 and 3, and Audio
4 corresponds to Video 1. You can change these assignments, see
page 33.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
adjust volume
external speakers
Connecting external speakers
The projector can be attached to external speakers that have their own
power source by plugging a speaker cable into the projector’s Audio Out
connector.
speaker
cable
Downloaded from ProjectorsManual.com Manuals
24
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.
Several features are provided to make giving presentation easier. The following is an overview, details are found in the menu section on page 27.
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
•
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to
image height. Standard TV screens and older laptops are 4:3; HDTV
and most DVDs are 16:9; and widescreen computers are 16:10. Choose
the option that best fits your input source. See page 28 for details.
•
Adjust the Color Temperature in the Advanced menu.
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later. See page 29.
Downloaded from ProjectorsManual.com Manuals
25
•
The Custom key, available on several optional remotes only, allows you
to assign various features to the key. The default effect is Source Info.
See page 35 for details.
•
The Freeze effect allows you to freeze the displayed image. This is useful if you want to make changes on your computer without your audience seeing them.
•
The Startup Logo menu option lets you change the default startup
screen to a black, white, blue, or a custom logo screen via Capture New.
See page 34.
•
Two menu options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 34.
•
A Low Power menu option is also available to help lower the projector’s fan sound volume. See page 34.
Optimizing video images
Customizing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.
You can customize the projector for your specific setup and needs. See
page 33 to page 36 for details on these features.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 28.
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. Standard TV screens and older laptops are 4:3; HDTV
and most DVDs are 16:9; and widescreen computers are 16:10. Choose
the option that best fits your input source. See page 28.
For ceiling mounted projection, turn Ceiling mode on in the Settings>System menu.
•
Specify which source the projector checks first for an active signal during power-up.
•
Turn the projector’s on-screen display messages on and off.
•
Select a Sharpness setting. See page 29.
•
Adjust the Color Temperature. Select a listed value, or select User and
individually adjust the intensity of the red, green, and blue color. See
page 29.
Downloaded from ProjectorsManual.com Manuals
26
•
Turn on power saving features.
•
Specify blank screen colors and startup logos.
•
Specify the menu language.
•
Control your projector using RS232 commands. See page 9 and
page 42.
Using the menus
To open the menus, press the menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous, then press Select to go to
the previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to five (the most nested menus).
Dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The Source Info menu provides a read-only display of information
about the projector and source.
Picture
menu
Certain menu items may be grayed out until a particular source is connected. For example, Tint is only available for video sources and will be hidden when a computer source is active. Other menu items may be grayed out
when they are not available. For example, Brightness is grayed out until an
image is active.
Source Info menu
Downloaded from ProjectorsManual.com Manuals
27
Settings
menu
Picture menu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
Keystone Vertical
increasing keystone
Keystone Vertical: adjusts the image vertically and makes a squarer image by
using an adjustable scale band.
decreasing keystone
Keystone Horizontal: adjusts the image horizontally and makes a squarer
image by using an adjustable scale band.
Corner Correction: allows you to adjust the corners of the projected image.
This is particularly helpful when stacking projectors. Select the corner you
would like to adjust within the Corner Correction submenu and follow the
instructions on the screen to make desired adjustments.
Keystone Horizontal
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image.
Color: (Computer 1 and video sources only) adjusts a video image from
black and white to fully saturated color.
Tint: (Computer 1 and NTSC video sources only) adjusts the red-green color
balance in the image.
Auto Image: resynchs the projector to the source.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
Standard TV screens and older laptops are 4:3; HDTV and most DVDs are
16:9; and widescreen computers are 16:10. The default is 16:10, which displays the input resized up or down to fill the display area.
Corner Correction
Downloaded from ProjectorsManual.com Manuals
28
Aspect Ratio
Presets: Presets are provided that optimize the projector for displaying computer presentations and video images in different lighting conditions and
on different backgrounds.
There are also user-definable presets. To set a preset for the current source,
adjust the image, select Save Settings in the Presets menu, then select Save
User Presets 1 (or 2 or 3). You can recall these settings in the future by selecting the User 1 preset. If you select User Presets then further adjust the
image, Presets Off will automatically be selected in the Preset menu to indicate changes have been made.
Save Settings
To restore the factory default settings, choose Factory Reset in the Settings>Service menu.
Presets
Advanced settings
Sharpness: changes the clarity of the edges of a video image. Select a sharpness setting.
Color Space: This option applies to computer and component video sources
(except 480i/576i). It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off
Auto, then choose RGB for computer sources, RGB Video for HDMI computer sources, and either REC709 or REC601 for component video sources.
Sharpness
Advanced
Color Temperature: changes the intensity of the colors. Select a listed value,
or select User and individually adjust the intensity of the red, green, and
blue colors.
Color Space
Color Temperature
Downloaded from ProjectorsManual.com Manuals
29
Video Standard: when set to Auto, the projector attempts to automatically
pick the video standard based on the input signal it receives. (The video
standard options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors may not look
right or the image may appear “torn.” If this happens, manually select a
video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
On: Always display captions. Off: Never display captions. Channel: Selects
which captions to display.
.
Video Standard
Active Iris: when on, the projector monitors the image brightness and modifies the light output if the image is dark, which improves black levels. In
Presentation mode, it looks at peak brightness, in Theater mode it looks at
average brightness.
Active Iris
Overscan: (Computer 1 and video sources only) removes noise around the
video image.
The following 4 options are for computer sources only:
Phase: adjusts the horizontal phase of computer 2, 3 and component (except
480i and 576i) sources.
Tracking: adjusts the horizontal scan of a computer source (except Computer
1).
Horizontal / Vertical Position: adjusts the position of a computer source
(except Computer 1) and Video 1 source (except 480i and 576i).
Resolution: When this feature is set to Auto, the projector attempts to pick
the resolution standard based on the input signal it receives. If the projector
is unable to detect the correct standard, the resolution may look odd. If this
happens, manually select the resolution from the menu which matches your
source signal.
Computer 2
Computer 2: allows you to turn Sync on Green on for this source.
Computer 3: allows you to turn Sync on Green on for this source.
Closed Captions: can be shown when the source is analog - component (480i
only), or S-video or composite (NTSC only). The video signal must also
include caption information. Auto: Display captions when sound is muted.
Downloaded from ProjectorsManual.com Manuals
30
Computer 3
Split Screen
Split Screen lets you show two different sources at the same time, one on the left half of the screen and the other on the right. The following source combinations are supported:
Table 2: Split Screen Matrix
Computer 1
Computer 2
Computer 1
X
Computer 3
Video 1
Video 2
Video 3
X
X
X
X
X
X
X
X
X
X
X
Computer 2
X
Computer 3
X
X
Video 1
X
X
X
Video 2
X
X
X
Video 3
X
X
X
Downloaded from ProjectorsManual.com Manuals
31
Exit or Previous: Removes the Split Screen Menu (if Split Screen is on) or goes
to the Picture menu (if Split Screen is off).
Most picture settings can’t be adjusted (e.g. Brightness, Contrast, Keystone,
Overscan, Presets, etc.).
Split Screen: Check the box to turn on Split Screen, or un-check it to turn off
Split Screen.
To change these settings:
Make sure the source you want to adjust is the main source (See above for a
description of the main source. If needed, go to the Split Screen Menu and
select Swap Left and Right or Main on Left/Right).
Main on Left/Right: Selects which side is the main (primary) side. Characteristics of the main side:
Source buttons, as well as Aspect Ratio and Auto Image buttons, affect the
main side only (unsupported source combinations are prevented – see
above table).
Turn off Split Screen (go to the Split Screen Menu, then select Main Menu,
or un-check Split Screen then select Previous).
Change picture settings.
Only sound from the main side is audible.
Turn on Split Screen (go to the Split Screen Menu, then check Split Screen).
When Split Screen is turned off, the main side is displayed full screen.
Some RS-232 commands have no effect. See the end of the RS-232 Command Additions section later in this document.
Swap Left and Right: Switches the left and right sources.
Left/Right Settings: Adjusts aspect ratio, phase, tracking, and horizontal/vertical position for the left or right side.
Left/Right Source: Selects the source to display on the left or right side (some
items will be disabled to prevent unsupported source combinations – see
above table).
Split Screen Menu
Source Info: Shows source information for the left and right sides.
Main Menu: Turns off Split Screen and goes to the Main Menu.
To program your remote’s Custom button to display the above Split Screen
Menu: Go to the Main Menu > Settings > Custom Key menu and select Split
Screen.
IMPORTANT - When Split Screen is on, some projector functions work differently:
The Main Menu and its sub-menus are not available – pressing the Menu
button shows the Split Screen Menu instead. To turn off Split Screen and
access other menus from the Split Screen Menu: select Main Menu, or uncheck Split Screen then select Previous.
Downloaded
from
ProjectorsManual.com
Manuals
Autosource
(source
search),
Closed Captions and
Magnify are not available.
32
Settings menu
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows
control of ceiling mounted projectors with a wall power switch.
Audio: allows adjustments to the volume. Also allows you to turn on and off
the Internal speakers and assign a particular source to a specific audio
input. If your HDMI source has problems with its audio stream, you can
mute it by selecting HDMI Noise Cancel.
Display Messages: displays status messages (such as “Searching”) in the
lower-left corner of the screen.
Monitor Out Default: Determines the source (either Computer 2 or Computer
3) which is output through the Monitor Out connector. Computer 2: Outputs Computer 2 unless current source is Computer 3 (in that case output
Computer 3 instead). Computer 3: Outputs Computer 3 unless current
source is Computer 2 (in that case output Computer 2 instead). Off: Outputs
the current source if it is Computer 2 or Computer 3. Otherwise do not output any signal.
Settings
menu
Audio
Sources: allows you to assign a particular input to a specific source key
when using the remote. Also allows selection of a default Startup Source
and enables or disables Autosource.
Sources>Power-up Source: this determines which source the projector checks
first for active signal during power-up.
Sources>Autosource: When Autosource is not checked, the projector defaults
to the source selected in Powerup Source. If no source is found, a blank
screen displays. When Autosource is checked, Powerup Source determines
which source the projector defaults to at power-up. If no signal is present,
the projector checks the sources in order until a source is found or until
power down.
Powerup
Source
Sources
System>Rear: reverses the image so you can project from behind a translucent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
WARNING: To prevent eye injury if the projector is ceiling mounted,
wear protective eyewear before opening lamp door. A warning sticker is
included with the user documentation. Place this sticker on the lamp
door if the projector is mounted on the ceiling.
IR Receivers: turns individual IR receivers off or on to avoid environmental interference.
IR Receivers
System
Downloaded from ProjectorsManual.com Manuals
33
on Black: Horizontal lines on a black background. Grid on White: Grid
on a white background. Grid on Black: Grid on a black background.
Low Power: toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter.
PC Screen Saver Off: prevents your notebook computer from going into
Screen Save mode. The projector must be connected to the PC via a USB
cable for this feature to work.
Screen Save
Power Save: automatically turns the lamp off after no signals are detected
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
down, the image will be displayed.
Screen Save: automatically blanks the screen after no signals are detected
for five minutes. The image returns when an active source is detected or
a remote or keypad button is pressed. Screen Save is disabled when
Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen when no source is detected at startup. It also
allows you to capture and display a custom startup screen.
Startup Logo
Capture New
To capture a custom logo, display the image you want to capture on
your computer and select the Capture New option. From the Capture
New menu, use the Capture Position X and Capture Position Y adjustments to frame the logo to be captured. Press Capture Start in the Capture New menu. The projector will let you know if the capture was a
success or a failure.
Blank Screen
The next time you start the projector, the custom logo you captured displays.
Blank Screen: determines what color is displayed when you press the
Blank button on an optional remote.
Ruled Lines: This feature displays line patterns that are useful when projecting onto a writeable surface, or when installing and setting up the
projector. Lines on White: Horizontal lines on a white background. Lines
Downloaded from ProjectorsManual.com Manuals
34
Ruled Lines
Custom Key (for use with optional remote only): allows you to assign a different function to the Custom key on the optional remote to quickly and easily use the effect. Only one effect can be enabled at a time. The default is
Source Info; highlight an effect and press Select to choose a different one.
IP Address: Identifies the projector on the network.
Subnet Mask: Separates the network address part of the IP address.
Default Gateway: The IP address of the local router.
Blank: shows an empty screen.
DNS Server: Shows the address of the DNS server.
Mute: turns off all sound.
DHCP: Select this to automatically obtain an IP address, Subnet mask,
and Default gateway.
AV Mute: turns off all sound and displays a blank screen.
AMX DD: When enabled, allows the AMX controller to dynamically
detect the projector.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes all sources to be reacquired.
Network Restart: Disconnects the projector from the network, gets a
new IP address, and reconnects.
Freeze: pauses the projected image.
Network Info: Provides information on the network configuration.
Magnify: allows you to enlarge a section of the projected image.
Ruled Lines: displays line patterns that are useful when projecting onto a
writeable surface, or when installing and setting up the projector.
Network
Split Screen: enables or disables Split Screen. Before using this for the
first time, configure Split Screen sources and layouts using the Split
Screen menu.
Source Info: displays the Source Info menu.
Service Info: displays the Service Info menu.
Network Info
Network: The projector has an RJ45 Ethernet connector that supports network connections and TCP/IP protocols. This will allow for the control and
management of the projector over a corporate network. Visit our website for
complete details on using the networking functionality. The following fields
are accessible when DHCP is not checked and available for manual entry of
data.
For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
Downloaded from ProjectorsManual.com Manuals
35
Language: allows you to select a language for the onscreen display of menus
and messages.
Language
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp and Filter Hours and Network settings) to their default after displaying a confirmation dialog box.
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu to
zero. Do this only after changing the lamp. It displays a confirmation dialog
box.
Reset Filter Hours: resets the filter counter in the Service Info menu to zero.
Do this only after cleaning the filter. It displays a confirmation dialog box.
Service Info: provides information for service.
Service Code: only used by authorized service personnel.
Service menu
Service Info
Downloaded from ProjectorsManual.com Manuals
36
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Downloaded from ProjectorsManual.com Manuals
37
Replacing the projection lamp
The lamp hour timer in the Service Info menu counts the number of hours
the lamp has been in use. Twenty hours before the specified end of the
lamp’s life, the message “Change lamp” briefly appears on the projected
screen.
hands after lamp replacement.
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
Service Info menu
NOTE: You can order new lamp housings from www.infocus.com (in select
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. InFocus is not liable for the performance, safety or
certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.
1 Turn off the projector and unplug the power cable.
2 Wait 45 minutes to allow the projector to cool thoroughly.
turn off and unplug
the projector
3 Loosen the lamp cover screw on the right side of the projector (marked
by the arrow) then slide and lift the lamp cover off.
wait 45 minutes
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 45 minutes before
you replace the lamp.
•
Only genuine InFocus lamps are tested with this projector. Use of other
lamps may cause electrical shock and fire.
•
To prevent eye injury if the projector is ceiling mounted, wear protective eyewear before opening lamp door. A warning sticker is included
with the user documentation. Place this sticker on the lamp door if the
projector is mounted on the ceiling.
•
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the bulb ruptures, small glass fragments may be generated.
The lamp housing is designed to contain these fragments, but use caution when removing
the lamp housing. Before
replacing the lamp,
Downloaded
from ProjectorsManual.com
Manuals
clean the lamp compartment and dispose of cleaning materials. Wash 38
lamp cover screw
4 Loosen the three captive screws (marked by the arrows) on the lamp
module. When replacing the lamp, never touch any screws without the
arrow mark.
loosen the captive screws on lamp module
5 Carefully remove the lamp module by grasping and lifting the handle.
lamp module handle
Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp module, making sure that it is properly seated, and
tighten the three captive screws.
7 Replace the cover over the lamp module by sliding it back into place and
tightening the screw.
8 Plug in the power cable, press the power switch then press the Power
button to turn the projector back on. Reset the lamp hour timer by navigating to the Settings>Service menu and selecting Reset Lamp Hours.
reset lamp hours in Service menu
Downloaded from ProjectorsManual.com Manuals
39
Cleaning the dust filter
1 Turn off the projector and unplug the power cable.
turn off and unplug
the projector
2 Wait 45 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 45
minutes before you clean or replace the dust filter.
wait 45 minutes
3 Remove the dust filter cover on the side of the projector by pressing up
on the two tabs at the cover’s bottom.
4 Pull the tab on the center of the black dust filter bracket and lift it off.
5 Clean the filter, cover, and vent using a vacuum set on low power.
Replace the filter if it is damaged or too dirty to clean.
6 Replace the dust filter and the bracket on the cover, then replace the
dust filter cover.
7 Reset the filter hour timer by navigating to the Settings>Service menu
tabs
and selecting Reset Filter Hours.
dust filter cover
reset filter hours in Service menu
Using the security lock
The projector has a security lock for use with a cable lock system. See the
Accessories catalog that came with the projector, or visit our website, for
ordering information. Refer to the information that came with the lock for
instructions on how to use it.
security lock
Downloaded from ProjectorsManual.com Manuals
40
Appendix
Projected image size
NOTE: Visit the Service section of our website for interactive image size calculators for the standard lense.
Table 3: Projection sizes: Standard lens (1.5 - 2.9:1 throw ratio)
Minimum Image
Maximum Image
Distance (feet/m)
Diagonal
Image
(feet/m)
Image
Width
(feet/m)
Diagonal
Image
(feet/m)
Image Width
(feet/m)
Min Distance
3/0.9
not
supported
not
supported
2.5/0.8
2.1/0.7
5/1.5
not
supported
not
supported
4.1/1.3
3.5/1.1
6/1.9
2.5/0.8
2.1/0.6
5.0/1.5
4.2/1.3
10/3.0
4.0/1.2
3.4/1.0
8.1/2.5
6.8/2.1
15/4.6
6.0/1.8
5.1/1.6
12.0/3.7
10.2/3.1
20/6.1
8.0/2.4
6.8/2.1
16.0/4.9
13.5/4.1
25/7.6
10.0/3.1
8.5/2.6
19.9/6.1
16.9/5.2
12.0/3.7
10.2/3.1
23.9/7.3
20.3/6.2
37/11.2
14.7/4.5
12.4/3.8
29.2/8.9
24.7/7.5
Max Distance
73/22.3
29.2/8.9
24.7/7.5
not
supported
not
supported
30/9.1
The image offset range for the standard lens is 10:0 (100%) to 1:1 (50%).
Downloaded from ProjectorsManual.com Manuals
41
Command Control
(starts the command
Serial Communication Configuration
AAA denotes the command
Visit our website for additional RS-232 settings and information.
? denotes the read request
To control this projector via RS-232, connect a null modem cable and set the
control system serial port settings to match the following communication
configuration:
) ends the command
A read command returns the range and the current setting, for example:
RS-232 Port Settings
Read Command Examples
Setting
Value
Function
Command
Response
Bits per second
19,200
Brightness
(BRT?)
(96-160,128)
Data bits
8
Volume
(VOL?)
(0-32,16)
Parity
None
Lamp Hours
(LMP?)
(0-32766, 42)
Stop bits
1
Flow control
None
Emulation
VT100
A write request example:
(AAA####) where
(starts the command
AAA denotes the command
Network Communication Configuration
#### denotes the value to be written
For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
(leading zeros not necessary)
) ends the command
Command Format
Some commands have ranges, while others are absolute. If a number
greater than the maximum range is received, it is automatically set to the
maximum number for that function. If a command is received that is not
understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on.
All commands consist of 3 alpha characters followed by a request, all
enclosed in parentheses. The request can be a read request (indicated by a
"?") or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
To assure the projector can process a command, wait 3 seconds before entering the next command.
(AAA?) where
Downloaded from ProjectorsManual.com Manuals
42
Write Command Examples
Function
Command
Response
Brightness
(BRT100)
Sets the brightness to 100
Power
(PWR0)
Turns power off
Power
(PWR1)
Turns power on
Com
mand
RW
Min
Max
Default
Step
Active Iris*
0: Off
1: Presentation
2: Film
IRI
RW
0
2
1
1
AMX Device Discovery Enable
0: Disable; 1: Enable
AMX
RW
0
1
0
1
Aspect Ratio
0: Auto
1: Native
2: 4:3
3: 16:9
6: 16:10
ARZ
RW
0
6
0
1
Aspect Ratio (Split
Screen left)
0: Auto
1: Native
2: 4:3
3: 16:9
6: 16:10
ARL
RW
0
6
0
1
Aspect Ratio (Split
Screen right)
0: Auto
1: Native
2: 4:3
3: 16:9
6: 16:10
ARR
RW
0
6
0
1
Function
Error Conditions
Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a command is received that
is not understood, a ‘?’ character will be returned indicating the command
was not understood.
Limitations
The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that the command
gets properly executed.
The Step column refers to increasing or decreasing the menu bar position
since the On-screen Display is not an exact match of values. For example,
Step 2 changes the data by 2 through the CLI (Command Line Interface).
The menu bar is up (or down) by 1.
Downloaded from ProjectorsManual.com Manuals
43
Auto Image
1: enable
AIM
W
n/a
1
n/a
1
Auto Power*
0: disable; 1: enable
APO
RW
0
1
0
1
Auto Source*
0: disable; 1: enable
ASC
RW
0
1
1
1
Blank
0: disable; 1: enable
BLK
RW
0
1
0
1
Blank Screen*
0: black
1: blue
2: white
BSC
RW
0
2
1
1
Brightness*
BRT
RW
96
160
128
1
Ceiling*
0: disable; 1: enable
CEL
RW
0
1
0
1
Closed Captions*
0: Off
1: On
2: Auto
CCD
RW
0
2
0
1
Closed Captions
Channel*
0: CC1
1: CC2
2: CC3
3: CC4
4: Text1
5: Text2
6: Text3
7: Text4
CCC
RW
0
7
0
1
Downloaded from ProjectorsManual.com Manuals
44
Color*
CLR
RW
96
160
128
1
Color Space*
0: Auto
1: RGB
2: REC709
3: REC601
4: RGB Video
CSM
RW
0
4
0
1
Color Temp*
0: 9300K
1: 6500K
2: 7200K
3: User
TMP
RW
0
3
2 (computer2,
3)
1
Contrast*
CON
RW
96
160
128
1
Corner Correction
Enable*
0: Disable; 1: Enable
CNE
RW
0
1
0
1
Corner CorrectionTop left corner -H*
CN1
RW
0
959
0
1
Corner CorrectionTop left corner -V*
CN2
RW
0
599
0
1
Corner CorrectionTop right corner -H*
CN3
RW
0
959
0
1
Corner CorrectionTop right corner -V*
CN4
RW
0
599
0
1
Corner CorrectionBottom left corner H*
CN5
RW
0
959
0
1
0 (computer1,
video)
Corner CorrectionBottom left corner V*
CN6
RW
0
599
0
1
Corner CorrectionBottom right corner H*
CN7
RW
0
959
0
1
Corner CorrectionBottom right corner V*
CN8
RW
0
599
0
1
Corner Correction all
corners Reset*
0: n/a
1: enable
CNR
RW
0
1
n/a
1
Source
0: computer1
1: computer2
2: computer 3
3: video 1
4: video 2
5: video 3
SRC
RW
0
5
0
1
Downloaded from ProjectorsManual.com Manuals
45
Custom Key (Effect)*
0: Blank
1: Mute
2: Aspect ratio
3: Source
4: Auto image
5: Freeze
6: Magnify
7: Source Info
8: Service Info
15: AV Mute
17: Split Screen
18: Ruled Lines
EFK
RW
0
18
7
1
Display Messages*
0: disable; 1: enable
DMG
RW
0
1
1
1
Factory Reset*
1: reset
RST
W
n/a
1
n/a
1
Filter Hours
RFT
R
0
32766
0
Freeze
0: disable; 1: enable
FRZ
RW
0
1
0
1
HDMI Noise Cancel*
0: Not Reset
1: Reset
HNC
RW
0
1
1
1
Horizontal Keystone*
DKH
RW
88
168
128
1
Horizontal Position
HPS
RW
Def.
-128
Def.
+128
auto
1
Horizontal Position
(Split Screen left)
HPL
RW
Def.
-128
Def.
+128
auto
1
Horizontal Position
(Split Screen right)
HPR
RW
Def.
-128
Def.
+128
auto
1
Internal Sound
Enable*
0: disable; 1: enable
INT
RW
0
1
1
1
IP Address Byte 1
IP1
R
0
1
192
IP Address Byte 2
IP2
R
0
1
168
IP Address Byte 3
IP3
R
0
1
1
IP Address Byte 4
IP4
R
0
1
254
IR Receiver front*
0: disable; 1: enable
IRF
RW
0
1
1
1
IR Receiver rear*
0: disable; 1: enable
IRR
RW
0
1
1
1
IR Receiver top*
0: disable; 1: enable
IRT
RW
0
1
0
1
Downloaded from ProjectorsManual.com Manuals
46
Language*
0 = English
1 = French
2 = German
3 = Italian
5 = Korean
6 = Norwegian
7 = Portuguese
8 = Russian
9 = Simp. Chinese
10 = Spanish
11 = Trad. Chinese
12 = Swedish
13 = Dutch
14 = Polish
15 = Turkish
16 = Danish
17 = Finnish
LAN
RW
0
17
0
Lamp Hours Used: All
Bulbs
LMT
R
0
21474
83646
0
Lamp Hours
LMP
R
0
32766
0
Lamp 1 Lasted (Hrs)
LB1
R
0
32766
0
Lamp 2 Lasted (Hrs)
LB2
R
0
32766
0
Lamp 3 Lasted (Hrs)
LB3
R
0
32766
0
Lamp Lit
0: not lit; 1: lit
LML
R
0
1
n/a
Lamp Resets (Total)
LMR
R
0
32766
0
Low Power*
0: disable; 1: enable
LPE
RW
0
1
0
1
1
Magnify*
MAG
RW
0
48
0
1
Magnify Enable*
0: disable; 1: enable
MGE
RW
0
1
0
1
Magnify Position Horizontal*
MPH
Magnify Position Vertical*
MPV
RW
0
64
32
Menu
0: clear; 1: display
MNU
RW
0
1
Menu Navigation
0: up key
1: down key
4: select key
NAV
W
0
Monitor Out Default*
1: Computer 2
2: Computer 3
5: Off
MO
D
RW
1
Mute
0: disable; 1: enable
MTE
RW
0
1
0
1
Network Restart*
1: restart
NTR
W
n/a
1
n/a
1
Overscan*
0: disable; 1: enable
OVS
RW
0
1
0
PC Screen Saver Off*
0: disable; 1: enable
NND
RW
0
1
Phase
MSS
RW
0
31
RW
0
Phase (Split Screen
left)
MSL
RW
0
31
0
1
Phase (Split Screen
right)
MSR
RW
0
31
0
1
PWR
RW
0
1
0
1
1
Power
0: Turn Off; 1: Turn
On
0
1
Power Save*
0: disable; 1: enable
PSV
RW
0
1
0
1
4
n/a
1
DSC
RW
0
5
0
1
5
1
1
Power-up Source*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
PST
RW
0
11
5 (computer
2, 3)
1
1
Presets*
0: user 1
1: user 2
2: user 3
3: Presets Off
5: presentation
7: video
10: bright
11: whiteboard
1
1
Rear*
0: disable; 1: enable
REA
RW
0
1
0
1
0
1
Reset Filter Hours
1: reset
FRT
W
n/a
1
n/a
1
64
32
1
Downloaded from ProjectorsManual.com Manuals
47
7 (computer1,
video)
Reset Lamp Hours
1: reset
LRT
W
n/a
1
n/a
1
Ruled Lines*
0: Lines on White
1: Lines on Black
2: Grid on White
3: Grid on Black
RLL
RW
0
3
0
1
Ruled Lines Enable
0: disable; 1: enable
RLE
RW
0
1
0
1
Save User Presets 13*
1: save
USn
W
n/a
1
n/a
1
Screen Save*
0: 5 minutes
1: 10 minutes
2: 15 minutes
3: 20 minutes
4: 25 minutes
5: 30 minutes
SSV
RW
0
5
0
1
Sharpness*
5 = Sharpest
6 = Sharper
7 = Standard
8 = Softer
9 = Softest
SHP
RW
5
9
7 (computer
and video 1)
6 (video 2
and 3)
1
Downloaded from ProjectorsManual.com Manuals
48
Source 0 Audio*
0: audio 1
1: audio 2
2: audio 3
3: audio 4
4: HDMI Internal
5: mute
SA0
RW
0
5
4
1
Source 1-5 Audio*
0: audio 1
1: audio 2
2: audio 3
3: audio 4
5: mute
SAn
RW
0
5
Source 1=
0
Source 2=
1
Source 3 =
3
Source 4 =
2
Source 5 =
2
1
Source 1*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
SR1
RW
0
5
0
1
Source 2*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
SR2
RW
0
5
1
1
Source 3*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
SR3
RW
0
5
3
1
Split Screen Right
Source
0: Computer 1
1: Computer 2
2: Computer 3
3: Video 1
4: Video 2
5: Video 3
SSR
RW
0
5
2
1
Source 4*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
SR4
RW
0
5
4
1
Split Screen Swap Left
and Right
1: Execute Swap
SSS
W
n/a
1
n/a
1
DSU
RW
0
2
1
1
1
Startup Logo*
0: blank screen
1: default
2: captured
Source Info
1: enable
ABT
W
n/a
1
n/a
Split Screen
0: Disable; 1: Enable
SSC
RW
0
1
RW
0
1
1
1
1
Sync on Green*
0: Disable; 1: Enable
SOG
0
Split Screen Main Side
0: Left; 1: Right
SSM
RW
0
Tint*
TNT
RW
96
160
128
1
1
0
1
Tracking
MTS
RW
def.
-384
def.
+384
auto
1
Split Screen Left
Source
0: Computer 1
1: Computer 2
2: Computer 3
3: Video 1
4: Video 2
5: Video 3
SSL
RW
0
5
1
1
Tracking (Split Screen
left)
MTL
RW
def.
-384
def.
+384
auto
1
Tracking (Split Screen
right)
MTR
RW
def.
-384
def.
+384
auto
1
Unit Total Time On
ONL
R
0
21474
83646
0
Vertical Keystone*
DKC
RW
48
208
128
Downloaded from ProjectorsManual.com Manuals
49
1
Vertical Position
VPS
RW
if
def<1
28 : 0
else:
def128
def+
128
auto
1
Vertical Position (Split
Screen left)
VPL
RW
if
def<1
28 : 0
else:
def128
def+
128
auto
1
Vertical Position (Split
Screen right)
VPR
RW
if
def<1
28 : 0
else:
def128
def+
128
auto
1
Video Standard*
0: Auto
1: NTSC
2: PAL
3: SECAM
VSU
RW
0
3
0
1
Volume
VOL
RW
0
32
16
1
Red Gain*
Green Gain*
Blue Gain*
RCG
GCG
BCG
RW
64
192
128
1
* These RS-232 commands have no effect when Split Screen is on.
Downloaded from ProjectorsManual.com Manuals
50
displaying
computer image 10
video images 13
dust filter, cleaning 40
E
elevator foot 11, 13
F
Factory Reset 36
filter, resetting hours 36
focus 11, 14
Freeze 35
fuzzy image 17
H
HDMI 6
HDTV sources 12
I
image
display computer 10
display video 13
size 7
image does not fit screen 18
image not centered 21
image not sharp 18
image not square 18
image reversed 19
image size matrix 41
image upside down 19
IP Address 35
IR Receivers 33
L
lamp hours, resetting 39
lamp replacement 38
lamp won’t turn on 20
Language 36
laptop
connecting 8
external video port 10
lens, cleaning 37
INDEX
Numerics
1920x1200 resolution 5
A
Aspect Ratio 28
audio 24
Audio In connector 8, 12
Auto Image 28
Auto Power 33
Autosource 33
B
Blank 35
BNC 8
Brightness 11
C
Capture Position 34
Capture Start 34
cleaning the dust filter 40
cleaning the lens 37
Color 14
colors are incorrect 19
component cable connector 12
computer connections
optional 8
required 8
computer image
displaying 10
optimize 25
connector panel 6
contacting service 21
Contrast 11, 14
custom logo startup screen 34
customer service contact information 21
D
Default gateway 35
DHCP 35
Display
Messages from
33
Downloaded
ProjectorsManual.com Manuals
51
RS-232
cable 9
connecting 6
S
screen saver, turning off 34
security lock 40
serial connection 6, 9
Service 36
Service Code 36
Service Info 36
Settings menu 33
shutting down projector 15
Source troubleshooting 16
Sources 33
Subnet mask 35
S-video connector 12
T
Tint 14
troubleshooting 15, 16
V
video connections 12
Video connector 12
video image
displaying 13
video images
optimizing 26
Video Standard 30
volume adjustment 14
W
warranty 21
X
XGA 5
Z
zoom 11, 14
Low Power 34
M
Magnify 35
Main menu 27
menu system 27
Monitor connector 9
Mute 35
N
Network 35
Network connector 9
Network Info 35
no computer image 17
no startup screen 16
O
only startup screen appears 16
Overscan 30
P
PC Screen Saver Off 34
Picture menu 28
power cable 8, 12
Power Save 34
Power-up Source 33
presentation features 25
projection distance 7
projector
connector panel 6
customizing 26
height 11, 13
positioning 7, 11, 13
setting up 7
shutdown 15
troubleshooting problems 15
R
Rear 33
remote control 23
replacing the lamp 38
Reset Filter Hours 40
resetting
lamp hours
39 ProjectorsManual.com Manuals
Downloaded
from
52
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement