InFocus IN3108 User Guide
IN3102 IN3104 IN3106 IN3108
Regulatory models W3220, W3240 and W3260
010-0710-03
Downloaded from ProjectorsManual.com Manuals
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland,
Oregon 97223-8368 USA
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
We declare under our sole responsibility that this projector conform to the
following directives and norms:
EMC Directive 2004/108/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 1st Edition
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks
of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows
are trademarks or registered trademarks of Microsoft Corporation. Adobe
and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks
or trademarks of InFocus Corporation in the United States and other
countries.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product
certification label.
This document applies to regulatory models W3220, W3240, and W3260.
Input ratings: 3.3 - 1.2A (W3220, W3260), 3.9 - 1.4A (W3240)
InFocus reserves the right to alter product offerings and specifications at
any time without notice.
Downloaded from ProjectorsManual.com Manuals
1
Important Operating Considerations for Safety
9
9
10
11
12
13
13
13
13
13
13
14
14
22
23
24
25
25
26
26
27
28
29
30
32
33
33
33
34
•
•
•
•
•
•
•
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
Use only InFocus-approved ceiling mounts. Warning: To prevent eye
injury if the projector is ceiling mounted, wear protective eyewear
before opening lamp door. A warning sticker is included with the user
documentation. Place this sticker on the lamp door if the projector is
mounted on the ceiling.
Only genuine InFocus lamps are tested for use in this projector.
InFocus is not liable for the performance, safety or certification of any
other lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector.
Use only the power cord provided. A surge-protected power strip is
recommended.
Refer to this guide for proper startup and shutdown procedures.
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
In the unlikely event of a lamp rupture, particles may exit through the
projector side vents. When the projector is turned on, keep people,
food, and drinks out of the "keep out" area under and around the
projector, as indicated by the "X" areas below.
2’ / 0
.6
8’ / 2
.4 m
5’
m
•
m
/1
3
5
6
9
3’
Table of Contents
Introduction
Positioning the projector
Projector and device connector guide
Connecting a computer source
Required computer connections
(DisplayLink or VESA)
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
HDMI 1.3 connection
S-video connection
VESA connection
Component video connection
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Maintenance
Cleaning the lens
Using the security lock
Replacing the projection lamp
m
.5
/1
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet.
Downloaded from ProjectorsManual.com Manuals
2
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN3102/
IN3104 has native XGA 1024x768 resolution, and the IN3106/IN3108 has
WXGA 1280x800 resolution. This guide applies to all products. They are
compatible with a wide variety of computers and video devices.
zoom (rear ring)
touch keypad
focus (front ring)
Product specifications
remote control
receiver (IR)
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
our website at www.infocus.com or at your retailer or dealer.
lens
elevator foot
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
power cord
connector
elevator foot
Downloaded from ProjectorsManual.com Manuals
3
connector
panel
remote control
receiver (IR)
Connector panel
The projector provides both computer and video connection options,
including:
•
VESA computer (2)
•
HDMI, for computer (1) and for video (1)
•
S-video
•
Composite video
•
Separate audio inputs for video and computer
•
USB DisplayLink connector, for computer audio/video input. This
USB connection also provides slide advance (and mouse control when
used with an optional remote control only)
composite
monitor out
video
audio in
HDMI for video
computer
S-video
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen
•
Audio out, to provide sound for external speakers
•
A 5 volt DC output (see below)
audio out
5 volt output
security lock
It also has an RS-232 connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
NOTE: DisplayLink video and audio is not sent to monitor out and audio
out.
5 volt DC output
The 3.5mm mini-jack triggers provide a 5 volt, 2 amp DC output. It provides
a constant output while the projector is on. It is designed to provide power
for an InFocus LiteShow II wireless device, which allows wireless
projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
Downloaded from ProjectorsManual.com Manuals
4
RS-232
DisplayLink
connector
Positioning the projector
10 ft high
image
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
•
bottom of image
1.24 ft above center
of lens
Position the projector the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
•
The image exits the projector at a given angle. IN3102/IN3104 image
offset is 115%; IN3106/IN3108 image offset is 112.4%. This means if
you have an image 10’ high, the bottom of the image will be 1.5'
(IN3102/IN3104) and 1.24' (IN3106/IN3108) above the center of the
lens.
Projection angle
(IN3102 & IN3104)
bottom of image
1.5 ft above center
of lens
lens center
lens center
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling mount” on page 31. We
recommend using an InFocus authorized ceiling mount.
•
10 ft high
(IN3106 & IN3108) image
Table 1: (IN3102 & IN3104)
Range of distance to the screen for a given screen size
Distance to screen
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Minimum
Distance (feet/
m)
60/1.5
80/2.0
90/2.3
150/3.8
8.6/2.6
11.5/3.5
12.9/3.9
21.5/6.6
7.8/2.4
10.4/3.2
11.7/3.6
19.5/5.9
Table 2: (IN3106 & IN3108)
Range of distance to the screen for a given screen size
Distance to screen
Downloaded from ProjectorsManual.com Manuals
5
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Minimum
Distance (feet/
m)
60/1.5
7.3/2.2
6.5/2.0
Projection angle
Table 2: (IN3106 & IN3108)
Range of distance to the screen for a given screen size
Distance to screen
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Minimum
Distance (feet/
m)
80/2.0
90/2.3
150/3.8
9.7/2.9
10.9/3.3
18.1/5.5
8.7/2.7
9.8/3.0
16.3/5.0
Downloaded from ProjectorsManual.com Manuals
6
Projector and device connector guide
The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as
computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite tuners,
camcorders, video games (progressive and interlaced), and laser disc players.
composite
monitor out
video
audio in
audio out
HDMI for video
computer
S-video
5 volt output
security lock
RS-232
Downloaded from ProjectorsManual.com Manuals
7
DisplayLink
connector
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital cable,
satellite TV, DVD, or VCR
Standard Video Camera
Video Compatibility
If Your Device
Connector Is
Attach to Adapter or
Labeled Connector
on Projector
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Composite video connection on
page 14.
Not for progressive
(i.e. HDTV) sources.
See page 9.
S-video connection on page 14
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Composite video connection on
page 14.
Not for progressive
(i.e. HDTV) sources.
See page 9.
S-video connection on page 14
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 3
or Video 2
Standard Video Game
Composite video connection on
page 14.
S-video connection on page 14
Downloaded from ProjectorsManual.com Manuals
8
Not for progressive
(i.e. HDTV) sources.
See page 9.
Video Device
HDTV
(High Definition TV)
Progressive DVD
Progressive Video Game
Attach to Adapter or
Labeled Connector
on Projector
Video Compatibility
If Your Device
Connector Is
1080i, 1080p, 720p
VGA
Computer 3 or
Computer 2
VESA connection on page 14
Component 480i
Component video
Computer 3 or
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 14
HDMI
HDMI connection on page 14
For Setup Instructions, see
1080i, 1080p, 720p
VGA
Computer 3 or
Computer 2
VESA connection on page 14
Component 480p
and 480i
Component video
Computer 3 or
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 14
HDMI
HDMI connection on page 14
1080i, 1080p, 720p
VGA
Computer 3 or
Computer 2
VESA connection on page 14
Component 480p
and 480i
Component video
Computer 3 or
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 14
HDMI
HDMI connection on page 14
Downloaded from ProjectorsManual.com Manuals
9
Comments
Connecting a computer source
connect USB cable
Required computer connections (DisplayLink or VESA)
If your computer has Windows XP SP2 or newer*, connect the USB cable
between your computer's USB port and the projector's DisplayLink connector,
then follow the instructions on the screen. See the DisplayLink Manager
User's Guide for more information.
MOLEX
MOLEX
* For the latest information about support for other operating systems
(including Apple), go to www.infocus.com/support/displaylink
connect computer cable
Or, connect one end of the provided computer cable to the Computer 2 or
Computer 3 connector on the projector and the other to the VESA connector
on your computer. If you are using a desktop computer, you will need to
disconnect the monitor cable from the computer’s video port first (you can
connect this monitor cable to the Monitor Out connector on the projector, see
below).
connect power cord
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status
Indicator Panel (page 15) turns amber.
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
connect audio cable
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
connect monitor cable
NOTE: DisplayLink video and audio is not sent to monitor out and audio out.
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable into the USB mouse connector on your computer and
the DisplayLink
connector
on the projector.
Downloaded
from ProjectorsManual.com
Manuals
10
Displaying an image
press Power button
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
? No start up screen? Get help on page 16.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VESA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to
learn your laptop’s key combination.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad.
Get help on page 16.
? Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Manager User's Guide for troubleshooting
information.
Downloaded from ProjectorsManual.com Manuals
11
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 5 for a table listing screen sizes and distances.
Adjust the zoom or focus.
adjust zoom or focus
zoom (rear ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 29 for
help with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 13.
adjust Basic Picture menu
Downloaded from ProjectorsManual.com Manuals
12
focus (front ring)
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu.
See page 29 for more information.
16:9
mode
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a
screen, the size/shape of the screen may determine which aspect ratio to
use. If you are projecting onto a blank wall, you don’t have the screen size
restriction. What you plan to project will also help you choose between 4:3
and 16:9. Most TV shows are 4:3, while most movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
Downloaded from ProjectorsManual.com Manuals
13
Video device connections
VESA connection
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the Computer 3 or Computer 2 connector on the
projector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 3 connector on the projector.
Component video connection
Plug the white connector of a Mini-plug audio Y-cable into the left audio
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In Video connector on the projector.
If your HD video device has component connectors, an optional
Component to VESA adapter can be used. Plug the component cable into
the video device. Plug the other end of the component cable into the adapter
and plug the adapter into the Computer 3 or Computer 2 connector.
Component offers the highest quality video output.
Keep in mind that video output from composite connections is not as high
quality as S-video.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video-out connector on the video device and into the HDMI connector on
the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than
composite.
Downloaded from ProjectorsManual.com Manuals
14
Shutting down the projector
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the
projector. The image returns when an active source is detected or a remote
or keypad button is pressed.
Table 3: Status indicator light behavior and meaning
Screen Save Time
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save Time feature in the Setup menu. See page 31.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction
with the projector is performed for 30 minutes. By default, this feature is off.
You can change the length of time, see page 31.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Icon
Meaning
Power, solid amber
The projector is plugged in.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 21). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/
support to contact service.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Downloaded from ProjectorsManual.com Manuals
15
Problem
Solution
Result
No start up screen
Plug power cord into the projector
press power button
Correct image
Startup
Screen
A
If your computer is using the projector's DisplayLink
connector, see the DisplayLink User's Guide for
troubleshooting information.
Only start up screen appears
Startup
Screen
Computer image projected
Press the Source button
activate laptop’s external port
A
A
A
Restart laptop
Downloaded from ProjectorsManual.com Manuals
16
Prolem
Solution
Result
No computer image, just the words “Signal out of
range”
Press the Auto Image button on keypad adjust computer
refresh rate in Control Panel > Display > Settings > Advanced
> Adapter (location varies by operating system)
Computer image projected
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image fuzzy or
cropped”
Only my laptop’s background appears, not the
Desktop icons
A
If your computer is using the DisplayLink connector, use
DisplayLink Manager software to change the display mode from
Extended Desktop to Duplicated Desktop. See the DisplayLink
Manager User's Guide for more information.
Disable “Extend my Windows Desktop” in Control Panel >
Display > Settings > Display 2 (location varies by operating
system)
Background and Desktop projected
A
A
A
Uncheck this
option, then
click Apply
Downloaded from ProjectorsManual.com Manuals
17
Prolem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turnon dual-display
mode
Image not centered on screen
Move projector, adjust zoom, adjust height
A
Adjust horizontal or
vertical position in
Advanced Picture
menu
Downloaded from ProjectorsManual.com Manuals
18
Correct image
Prolem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Image does not fit 4:3 or 16:9 screen
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect ratio menu
Correct image
Downloaded from ProjectorsManual.com Manuals
19
Prolem
Image upside down
A
Image reversed left to right
Solution
Result
Turn off Ceiling Mount in Setup menu
Correct image
Turn off Rear Project in Setup menu
Correct image
Adjust color, tint, brightness, contrast in the Basic
Picture menu
Correct image
A
Projected colors don’t match source
COLOR
COLOR
Downloaded from ProjectorsManual.com Manuals
20
Prolem
Solution
Result
The video embedded in my PowerPoint presentation
does not play on the screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink User's Guide for video
troubleshooting information.
Turn off the internal LCD display on your laptop
Embedded video plays correctly
A
A
A
B
A
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Startup
Screen
A
Temperature light
Downloaded from ProjectorsManual.com Manuals
21
B
Prolem
Solution
Result
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Lamp must be replaced (see page 35)
lamp door
A
Lamp light
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call us.
Check out our HOW TO section there for additional information on using
this projector for home theater or gaming applications. See the Quick Start
Poster/Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
Downloaded from ProjectorsManual.com Manuals
22
Lamp turns on
Startup
Screen
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an
environmentally proper manner.
navigation
buttons
To operate, point the remote at the front of the projector (not at the
computer). The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 15
for shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 28 for more info on the menus.
The remote also has a Source button to switch between sources.
The remote also has:
•
•
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank
Screen or Freeze (see page 31).
• Source button to switch between sources.
• Blank button to blank the screen.
• Presets button to select stored settings (see page 29).
• Mute button to silence the audio.
• Auto Image button to resynch the projector to the source
• Resize button to switch among aspect ratios (see page 29).
Troubleshooting the remote
•
•
Make sure the batteries are installed in the proper orientation and are
not dead.
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point
remote at the projector.
Downloaded
from the
ProjectorsManual.com
Manuals
23
Using the audio
connect audio cable
Using the projector’s speakers
When the computer is using the DisplayLink connector, both audio and
video are sent over the USB cable to the projector and audio will play from
the projector's speakers.
For inputs other than DisplayLink, to use the projector's speakers, connect
the audio source to the Audio In Computer or Video connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
adjust volume
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for audio troubleshooting
information
•
Make sure the audio cable is connected to the correct Audio In
connector, Computer or Video.
•
Make sure the volume is turned up enough. Press the Volume button on
the keypad or remote.
•
Make sure the correct source is active.
•
Make sure that you are connected to an “audio out” connector on the
source as opposed to a “line-in” or “microphone” connector.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
external speakers
with own power
source
speaker
cable
Connecting external speakers
The projector can be attached to external amplified speakers by connecting
a 3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
system and connect the audio directly from your source to a stereo or home
theater system.
Downloaded from ProjectorsManual.com Manuals
24
audio out
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an
overview of their functions:
Power–turns the projector on and off (page 11).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 29).
Keystone–adjusts squareness of the image (page 12).
Menu–opens the on-screen menus (page 28).
menu navigation
buttons
Select–confirms choices made in the menus (page 28).
Up/Down arrows–navigates to and adjusts settings in the menus (page 28).
Volume–adjusts sound (page 24).
Source–changes the active source (page 11).
Downloaded from ProjectorsManual.com Manuals
25
Optimizing computer images
Presentation features
After the projector is running and the image is on the screen, you can
optimize the image using the onscreen menus. For general information on
using the menus, see page 28.
Several features are provided to make giving presentations easier. Here is
an overview, details are found in the menu section.
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
(page 29).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
•
Adjust the Color Temperature in the Advanced Picture menu
(page 29).
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced Picture menu (page 30).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 29).
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for information about
optimizing images.
Downloaded from ProjectorsManual.com Manuals
26
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
projector and current source. See page 31 for details.
•
The Search Screen option lets you change the appearance of the blank
screen and start up screen (page 32).
•
Two options, Auto Off and Screen Save Time, are provided to
automatically shut down the projector after several minutes of
inactivity or display a black screen. This helps preserve lamp life
(page 31).
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 28.
You can customize the projector for your specific setup and needs. See
page 31 to page 32 for details on these features.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic
Picture menu (page 29).
•
For rear projection, turn Rear Project on in the Setup menu.
•
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
For ceiling mounted projection, turn Ceiling Mount on in the Setup
menu.
•
•
Select a Sharpness setting (page 29).
Specify which source the projector checks first for active video during
power-up.
•
Adjust the Color Temperature. Select a listed warmth value (page 30).
•
Specify the function of the Custom key on the remote.
•
Turn on Overscan to remove noise on the edges of the image (page 30).
•
Turn the projector’s display messages on and off.
•
Turn on power saving features.
•
Specify appearance of blank screen and startup screen.
•
Specify the language viewed on the menus.
•
Save settings for the active source as a preset.
Dynamic Messaging
You can use Command Line Interface (CLI) commands to display text
messages on the projector (for example, to display urgent alert messages to
employees). This requires a connection to the projector’s RS-232 serial
control connector. Go to our support website to download the RS-232
command reference for your projector.
Downloaded from ProjectorsManual.com Manuals
27
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use
the arrow buttons to move up and down to highlight the desired menu,
then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value or select an option or turn the
feature on or off. Press Select to confirm your changes. Use the arrows to
navigate to another setting. When your adjustments are complete, press
Menu to access a different menu; press the Menu button at any time to
navigate to the higher-level menu and ultimately close the menus.
The menus are grouped by usage:
•
The Basic Picture menu provides common image adjustments.
•
The Advanced Picture menu provides more complex image
adjustments.
•
The Setup menu provides set-up type adjustments that are not changed
often.
•
The Status and Service menu provides information about the projector
and source.
Downloaded from ProjectorsManual.com Manuals
28
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Basic Picture menu
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch
enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 13.
Apply Preset...: Presets are provided that optimize the projector for
displaying computer presentations and video images under certain
conditions.
Aspect ratio
There is also a user-definable preset. To set this preset, adjust the image and
select Save User in the Presets menu. You can recall these settings in the
future by selecting the User preset.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Digital Zoom: changes the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its
size has been changed by the Digital Zoom setting.
increasing keystone
Downloaded from ProjectorsManual.com Manuals
29
decreasing keystone
Advanced Picture menu
BrilliantColor™: produces an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer
sources.
White Peaking: (video sources only) increases the brightness of whites that
are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed relative
warmth value.
Advanced Picture menu
Force wide: when this is off, the analog locking algorithms choose the
standard mode resolution (4:3) as the preferred default resolution. When
this is on, the analog locking algorithms choose wide mode resolution
(16:10) as the preferred default resolution.
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Color Space: This option applies to computer and component video sources.
It allows you to select a color space that has been specifically tuned for the
input signal. When Auto is selected, the projector automatically determines
the standard. To choose a different setting, turn off Auto, then choose RGB
for computer sources or choose either REC709 or REC601 for component
video sources.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Horizontal/Vertical Position: adjusts the position of a computer source.
Downloaded from ProjectorsManual.com Manuals
30
Setup menu
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter.
Language: allows you to select a language for the onscreen display.
Key Click: turns the key click sound on or off. When this setting is on,
pressing keys on the keypad causes the projector’s speaker to play a “click”
sound.
Power Sounds: controls whether the projector makes a sound when powered
on and off.
Auto Source: When this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by
pressing the Source button on the remote or keypad.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and
press Select to choose a different one.
•
•
•
Source Info: the default action. Shows the Source Info menu.
Projector Info: Shows the Projector Info menu.
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 13 and
page 29).
• Auto Image: resets the projector to the source (page 25).
• Overscan: removes noise around the image.
• Blank Screen: displays an empty screen.
• Freeze Screen: pauses the projected image.
• Mute: turns off all sound.
• Source: cycles through available sources.
Blank Key: Select what to display when the blank key on the remote is
depressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
Setup menu
Power-up Source: determines which source the projector checks first for
active video during power-up.
HDMI DDC: When this feature is set to On, the projector will support an
older DVD player for HDMI port.
AC Power On: When this feature is on, the projector automatically turns on
when electrical power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the colors
may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Screen Save Time: automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns
when an active source is detected or a remote or keypad button is pressed.
Closed Captions: controls closed caption display while audio is not muted. If
this setting is not off, and audio is not muted, and the source is NTSC and
Downloaded from ProjectorsManual.com Manuals
31
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
press the Select button in order to access the “Wrong PIN” message and reenter the code.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
To enter the PIN at projector startup:
Rear Project: reverses the image so you can project from behind a
translucent screen.
Power up the projector. The “Enter PIN” dialog box appears after the
startup screen. Enter the PIN. Use the navigation buttons on the remote or
keypad to enter the correct button press sequence. See the description above
for instructions.
Auto Keystone: automatically adjusts vertical image.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the up and
down buttons on the keypad. Select OK or Cancel by pressing the Select
button. Verify the new PIN.
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Take Snapshot...: Captures the current image and allows it to be used as the
search screen image.
If you lose or forget your custom PIN:
Show Messages: displays status messages (such as “Searching”) in the lowerleft corner of the screen.
Contact InFocus support. Go to www.infocus.com/support
Computer 2 SCART: Selects SCART connection type between RGB and
composite.
Menu Offset: allows you to change the position of the On Screen Display
items.
Serial Port, Baud Rate: selects the serial port and baud rate.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
Serial Port Echo: controls whether the serial port echoes characters.
Magnify Controls: determines whether the select key can be used to change
magnify settings when the OSD menu is not visible.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image. The default PIN on this
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the
remote or keypad to enter the correct 5-button press sequence. When all 5
numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Wrong PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
Downloaded from ProjectorsManual.com Manuals
32
Status and Service menu
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
Factory Reset: restores all settings to their default.
Service Code: only used by authorized service personnel.
Status and Service menu
Downloaded from ProjectorsManual.com Manuals
33
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
security
lock
Downloaded from ProjectorsManual.com Manuals
34
Replacing the projection lamp
•
The Lamp Hours timer in the Projector Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Replace lamp” appears on the screen at startup.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
1 Turn off the projector and unplug the power cord.
2 Wait 60 minutes to allow the projector to cool thoroughly.
NOTE: Be sure to use the InFocus lamp module designed for this
projector. You can order new lamps from www.infocus.com (in select
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. Use of non InFocus lamps may cause electrical
shock and fire, and may void the projector warranty. InFocus is not
liable for the performance, safety or certification of any other lamps.
3 Remove the lamp door by: (a) removing the screw (labeled “1”) on the
side of the lamp door, (b) turning the lamp cover knob (labeled “2”)
counterclockwise to push up the lamp cover, and (c) lifting the door off.
turn off and unplug
projector
WARNINGS:
•
•
•
•
•
•
•
•
The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can
obscure projection sharpness and may cause the glass to shatter.
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it.
Before replacing a ruptured lamp, clean the lamp compartment and
dispose of cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
wait 60 minutes
c
b
Downloaded from ProjectorsManual.com Manuals
35
a
4 Loosen the captive screws that attach the lamp housing to the projector.
Carefully remove the lamp housing. Dispose of the lamp in an
environmentally proper manner.
loosen screw
5 Install the new lamp module and tighten the screws.
6 Replace the lamp door by sliding it into place.
7 Plug in the power cord and press the Power button to turn the projector
back on.
8 To reset the lamp hour timer, navigate to the Status and Service menu and
select Reset Lamp Hours (page 33).
Downloaded from ProjectorsManual.com Manuals
36
INDEX
Numerics
16x9 vs 4x3 12
5 volt DC output 4
A
AC Power On 30
Advanced menu 29
Apply Preset 28
Aspect Ratio 12, 28, 30
Audio In Computer connector 9
Audio In connector 13
Audio Out connector 23
Auto Image 30
Auto Off Time 30
Auto Source 30
B
Blank Key 30
Blank Screen 30
Brightness 28
BrilliantColor 29
C
cable box 12
Ceiling Mount 30
Cleaning the lens 33
Closed Captions 30
Color Space 29
Color Temperature 29
Computer In connector 9
Connecting
external speakers 23
computer 9
video device 12
Connector on Projector 7, 8
Connector panel 4
contacting InFocus 21
Contrast 28
Custom Key 30
Custom key 25
Downloaded
from information
ProjectorsManual.com
Manuals
customer
service contact
21
Customizing the projector 26
D
DVDs 28
F
Factory Reset 32
focus 11
Force wide 29
Freeze Screen 30
G
Gamma 29
H
HDMI 1.3 connection 13
HDMI DDC 30
HDTV 6, 28
Horizontal 29
I
Image
Size 5
Optimization 25
K
Key Click 30
keypad buttons 24
Keystone 28
keystone, adjusting 11
L
Lamp hours, resetting 35
Lamp Low Power 30
Language 30
laptop video port activation 10
LEDs 14
leveling foot 11
M
Maintaining the projector 33
Menu button 27
menu usage 27
Monitor Out connector 9
Mute 30
O
Optimizing images 25
Optimizing video 26
37
Overscan 29, 30
P
Phase 29
Picture menu 28
Power connector 9
power cord 9
Power Sounds 30
Power-up Source 30
Presentation features 25
Projection distance 5
Projector
Connector panel 4
Customization 26
Image Size 5
keypad buttons 24
Maintenance 33
menus 27
offset 5
Registering 3
security lock 33
Status indicator panel 14
connecting computers 9
connecting video devices 12
positioning 5
setting up 5
shutting down 14
troubleshooting problems 14
Projector Info 30
R
Rear 31
Registering your projector 3
remote control 22
Reset 32
Resetting the projector 32
RS-232 4
S
Safety Considerations 2
Screen Aspect 12
Screen Save 14, 30
Screen
triggers 4 from ProjectorsManual.com Manuals
Downloaded
Search Screen 31
security lock 33
Service 32
Service Code 32
Sharpness 28
shutting down the projector 14
Source 30
Source Info 30
speakers, connecting external 23
Status indicator panel 14
S-video connector 13
Sync Threshold 29
T
Tint 28
Tracking 29
troubleshooting 14
TV tuner 12
U
USB 4, 9
V
Vertical 29
video optimizing 26
Video Standard 30
Volume button 23
W
warranty 21
White Peaking 29
Z
zoom 11
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement