Infocus IN1501, IN1503 User manual

Infocus IN1501, IN1503 User manual
IN1501, IN1503
Downloaded from ProjectorsManual.com Manuals
009-1313-00
Regulatory models: P1501, P1503
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon
97070-8238 USA
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may
void authority to operate the equipment.
We declare under our sole responsibility that this projector conforms to the
following directives and norms:
EuP Directive 2005/32/EC
EMC Directive 2004/108/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 2005 (MOD)
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM is a trademark or registered trademark of International
Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or
registered trademarks of Microsoft Corporation. Adobe and Acrobat are
trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and
the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™
is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized)
are either registered trademarks or trademarks of InFocus Corporation in the
United States and other countries.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
cTUVus
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory models P1501 and P1503.
Input ratings: 100-240Vac, 2.9A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
Downloaded from ProjectorsManual.com Manuals
1
Table of Contents
Introduction
Positioning the projector
Projector and device connector guide
Connecting a computer source
Required computer connections
(DisplayLink or VGA)
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
HDMI 1.3 connection
VGA connection
Component video connection
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Maintenance
Cleaning the lens
Using the security lock
Replacing the projection lamp
3
5
6
9
9
9
10
11
12
13
13
13
13
13
14
14
22
23
24
25
25
26
26
27
28
29
30
32
33
33
33
34
Downloaded from ProjectorsManual.com Manuals
2
Important Operating Considerations for Safety
•
Refer to this guide for proper startup and shutdown procedures.
•
Follow all warnings and cautions in this manual and on the projector.
•
Place the projector in a horizontal position no greater than 15 degrees off
axis.
•
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
•
Do not block ventilation openings. Locate the projector in a well-ventilated
area without obstructions to intake or exhaust vents. Do not place the
projector on a tablecloth or other soft covering that may block the vents.
•
Do not place the projector in direct sunlight, humid, greasy or dusty places or
in places where the projector may come into contact with smoke or steam.
•
Do not look directly into the lens while the projector is being used.
•
Do not drop the projector.
•
Do not spill liquid on the projector. Spilled liquid may damage the projector.
•
Use the power cord provided. Connect the power cord to a receptacle with
a protective safety (earth) ground terminal. A surge-protected power strip is
recommended.
•
Do not overload wall outlets.
•
When disconnecting the power cord, hold the plug, not the cord.
•
Wash hands after handling the cables supplied with this product.
•
The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in accordance
with local disposal laws.
•
Use an InFocus approved ceiling mount kit for proper fitting, ventilation and
installation. The warranty does not cover any damage caused by use of nonapproved ceiling mount kits or by installing in an improper location.
•
When the projector is ceiling mounted, wear protective eyewear to prevent
eye injury before opening lamp door.
•
Refer all service to qualified service personnel. Servicing your own projector
can be dangerous to you and will void the warranty.
•
Only use replacement parts specified by InFocus. Unauthorized substitutions
may result in fire, electrical shock, or injury, and may void the warranty
•
Only genuine InFocus lamps are tested for use in this projector. Use of non
InFocus lamps may cause electrical shock and fire, and may void the projector
warranty.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out" area
under and around the projector, as indicated by the "X" areas below.
2’
8’ / 2
.4 m
/
5’
m
1.5
/0
.6
m
3’ / 1
m
Follow these instructions to help ensure image quality and lamp life over the life of
the projector. Failure to follow these instructions may affect the warranty. For
complete details of the warranty, see the Warranty Booklet.
Downloaded from ProjectorsManual.com Manuals
3
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward
to maintain. It is a versatile projector that is flexible enough for business
presentations and home video viewing too. The IN1501 has native XGA 1024x768
resolution, and the IN1503 has WXGA 1280x800 resolution. This guide applies to
all products. They are compatible with a wide variety of computers and video
devices.
zoom (rear ring)
touch keypad
focus (front ring)
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our
website at www.infocus.com, as specifications are subject to change.
Accessories
lens
The standard accessories that came with your projector are listed in the included
Quick Start Poster/Booklet. Optional accessories can be found on our website at
www.infocus.com or at your retailer or dealer.
remote control
receiver (IR)
elevator foot
Online registration
Register your projector on our website at www.infocus.com/register to activate
your warranty and receive product updates, announcements, and registration
incentives.
remote control
receiver (IR)
Downloaded from ProjectorsManual.com Manuals
4
power cord
connector
connector
panel
Connector panel
The projector provides both computer and video connection options, including:
•
•
•
•
•
•
VGA computer
HDMI
Composite video
USB DisplayLink connector, for computer audio/video input. This USB
connection also provides slide advance (and mouse control when used with
an optional remote control only)
LitePort, for connecting a USB flash drive containing images.
Audio input for video and computer.
composite
video
computer
LitePort (IN1503 only)
audio in
HDMI
DisplayLink
Downloaded from ProjectorsManual.com Manuals
5
security lock
Positioning the projector
Table 1: (IN1501)
Range of distance to the screen for a given screen size
To determine where to position the projector, consider the size and shape of your
screen, the location of your power outlets, and the distance between the projector
and the rest of your equipment. Here are some general guidelines:
•
•
•
•
•
Distance to screen
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
Position the projector within 10 feet (3m) of your power source and within 6
feet (1.8m) of your video device (unless you purchase extension cables). To
ensure adequate cable access, do not place the projector within 6 inches
(.15m) of a wall or other object.
If you are installing the projector on the ceiling, we strongly recommend using
InFocus approved ceiling mounts for proper fitting, ventilation and installation.
Refer to the installation guide that comes with the InFocus Ceiling Mount Kit
(p/n SP-CEIL-UNIV) for more information. The warranty does not cover any
damage caused by use of non-approved ceiling mount kits or by installing in an
improper locationTo turn the image upside down, see “Ceiling mount” on
page 31. We recommend using an InFocus authorized ceiling mount.
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the video
format determine the size of the projected image.
The image exits the projector at a given angle. IN1501 image offset is 120% +/
-5% ; IN1503 image offset is 105% +/-5%. This means that if you have an image
10’ high, the bottom of the image will be 1.2' (IN1501) and 1.05' (IN1503)
above the center of the lens.
10 ft high
image
(IN1501)
bottom of image
1.2 ft above center
of lens
lens center
Projection angle
10 ft high
image
Minimum
distance (inches/
m)
Maximum
Distance
(inches/m)
60/1.5
80/2.0
90/2.3
150/3.8
43/1.1
57/1.5
64/1.6
107/2.7
52/1.3
69/1.7
77/2.0
129/3.3
Table 2: (IN1503)
Range of distance to the screen for a given screen size
Distance to screen
(IN1503)
bottom of image
1.05 ft above center
of lens
Diagonal Screen
Size (inches/m)
Projection angle
lens center
Downloaded from ProjectorsManual.com Manuals
6
Diagonal Screen
Size (inches/m)
Minimum
distance (inches/
m)
Maximum
Distance
(inches/m)
60/1.5
80/2.0
90/2.3
150/3.8
37/0.9
49/1.2
55/1.4
92/2.3
44/1.1
59/1.5
66/1.7
110/2.8
Connecting a computer source
DisplayLink
connect USB cable
If you have a Windows or Macintosh computer, connect the USB cable between
your computer's USB port and the projector's DisplayLink connector*. Then to
begin installation of the DisplayLink software:
Windows: Follow the instructions on the screen.
MOLEX
MOLEX
Macintosh: A folder will open containing a file named DisplayLink Installer.pkg.
Open that file and follow the instructions on the screen.
connect VGA cable
* For detailed DisplayLink instructions and troubleshooting, and to download the
latest DisplayLink software, go to www.infocus.com/support/displaylink
VGA connection
Connect one end of the provided computer cable to the VGA connector on the
projector and the other to the VGA connector on your computer. If you are using
a desktop computer, you will need to disconnect the monitor cable from the
computer’s video port first.
connect power cord
Connecting power
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status Indicator
Panel (page 12) turns amber.
connect audio cable
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
To advance slides in a PowerPoint presentation using the remote control, plug the
USB cable into the USB mouse connector on your computer and the DisplayLink
connector
on the projector.
Downloaded
from ProjectorsManual.com Manuals
7
Displaying an image
press Power button
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp comes
on, the start up screen displays and the Power button is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 13.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source
button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD key
turns the external display on and off. Locate a function key labeled CRT/LCD or a
function key with a monitor symbol. Press FN and the labeled function key
simultaneously. Refer to your laptop's documentation for more information about
your laptop's key combination or go to the InFocus website at: http://
www.infocus.com/Support/LaptopActivation.aspx.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad. Get
help on page 13.
? Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Software User's Guide (available on the InFocus website
at www.infocus.com/displaylink) for troubleshooting information.
Downloaded from ProjectorsManual.com Manuals
8
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot release
button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the side of the projector.
adjust distance
Position the projector the desired distance from the screen at a 90 degree angle to
the screen.
See page 6 for a table listing screen sizes and distances.
Adjust the zoom or focus.
adjust zoom or focus
If the image is not square, first make sure that the projector is perpendicular to the
screen. If the image is larger or smaller on the top or bottom edge of the screen,
press the top Keystone button to reduce the upper part of the image, and press
the bottom Keystone button to reduce the lower part.
zoom (rear ring)
If the left or right side of the screen is larger or smaller the other, you can turn the
projector to the left or to the right a few degrees to square the image.
adjust keystone
Adjust the Contrast or Brightness in the Basic Picture menu. See page 26 for help
with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in
order to view the highest quality image. For more information regarding Aspect
Ratio, see page 10.
adjust Basic Picture menu
Downloaded from ProjectorsManual.com Manuals
9
focus (front ring)
What is Aspect Ratio?
4:3 screen
Aspect ratio is the ratio of the image width to image height. Standard TV screens
and older laptops are 4:3; HDTV and most DVDs are 16:9; and widescreen
computers are 16:10. If you are projecting onto a screen, the size/shape of the
screen will influence the aspect ratio you decide to use. If you are projecting onto
a blank wall, there are no screen size restrictions. What you plan to project will
also help you choose between 4:3, 16:9 or 16:10. Many TV shows are 4:3, while
most movies are 16:9.
16:9 screen
4:3
mode
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3 screen
you should still use 16:9 for widescreen movies or HDTV, but you also have the
option of using either 4:3 (to fill the screen) or Native (for direct pixel mapping)
for 4:3 content. Force Wide can also be enabled to automatically resize less
common aspect ratios to 16:10.
16:9
mode
Native
mode
(NTSC
only)
Downloaded from ProjectorsManual.com Manuals
10
Connecting a video device
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
You can connect video devices such as VCRs, DVD players, camcorders, digital
cameras, video game consoles, HDTV receivers, and TV tuners to the projector.
You can connect the audio directly to the projector to get sound from the built-in
speaker, or you can bypass the projector’s audio system and connect the audio
directly from your source to a stereo or home theater system.
You can connect the projector to most video devices that can output video. You
cannot directly connect the coaxial cable that enters your house from a cable or
satellite company, the signal must pass through a tuner first. Examples of tuners
are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.
Basically, any device that can change channels is considered a tuner.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector
may be labeled “To Monitor” on the video source. Plug the computer cable into
the VGA connector on the projector.
Component video connection
If your HD video device has component connectors, an optional Component to
VGA adapter can be used. Plug the component cable into the video device. Plug
the other end of the component cable into the adapter and plug the adapter into
the VGA connector.
Before connecting your projector, you should decide which aspect ratio you want
to use. The projector’s Aspect Ratio setting is accessed through the Resize button
on the remote or through the projector’s Basic Picture Menu. See page 26 for
more information.Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector
on the video device. Plug the other yellow connector into the yellow Video
connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio out
connector on the video device and plug the red connector into the right audio out
connector on the video device. Plug the other end of the cable into the Audio In
connector on the projector.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
Downloaded from ProjectorsManual.com Manuals
11
Shutting down the projector
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector.
The image returns when an active source is detected or a remote or keypad
button is pressed.
Table 3: Status indicator light behavior and meaning
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning
on the Screen Save Time feature in the Setup menu. See page 28.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 28.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The
lamp turns off and the LED blinks amber for 1 minute while the fans continue to
run to cool the lamp. When the lamp has cooled, the LED lights amber and the
fans stop. Unplug the power cable to completely power off the projector.
Icon
Meaning
Power, solid amber
The projector is plugged in.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 18). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/
support to contact service.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does
not, troubleshoot the setup.
Downloaded from ProjectorsManual.com Manuals
12
Problem
Solution
Result
No start up screen
Plug power cord into the projector
press power button
Correct image
Startup
Screen
Only start up screen appears
Startup
Screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink Software User's
Guide for troubleshooting information.
Computer image projected
Press the Source button
activate laptop’s external port
A
A
A
Restart laptop
Downloaded from ProjectorsManual.com Manuals
13
Problem
Solution
Result
No computer image, just the words “Signal out of
range”
Press the Auto Image button on keypad adjust computer
refresh rate in Control Panel > Display > Settings > Advanced
> Adapter (location varies by operating system)
Computer image projected
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image fuzzy or
cropped”
Only my laptop’s background appears, not the
Desktop icons
A
If your computer is using the DisplayLink connector, use
DisplayLink Manager software to change the display mode from
Extended Desktop to Duplicated Desktop. See the DisplayLink
Software User's Guide for more information.
Disable “Extend my Windows Desktop” in Control Panel >
Display > Settings > Display 2 (location varies by operating
system)
Background and Desktop projected
A
A
A
Uncheck this
option, then
click Apply
Downloaded from ProjectorsManual.com Manuals
14
Problem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turnon dual-display
mode
Image not centered on screen
Move projector, adjust zoom, adjust height
Adjust horizontal or
vertical position in
Advanced Picture
menu
Downloaded from ProjectorsManual.com Manuals
15
Correct image
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Image does not fit 4:3 or 16:9 screen
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect ratio menu
Correct image
Downloaded from ProjectorsManual.com Manuals
16
Problem
Image upside down
A
Image reversed left to right
Solution
Result
Turn off Ceiling Mount in Setup menu
Correct image
Turn off Rear Project in Setup menu
Correct image
Adjust color, tint, brightness, contrast in the Basic
Picture menu
Correct image
A
Projected colors don’t match source
COLOR
COLOR
Downloaded from ProjectorsManual.com Manuals
17
Problem
Solution
Result
The video embedded in my PowerPoint presentation
does not play on the screen
If your computer is using the projector's DisplayLink
connector, see the DisplayLink Software User's Guide
for video troubleshooting information.
Turn off the internal LCD display on your laptop
Embedded video plays correctly
A
A
B
A
B
A
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Startup
Screen
Temperature light
Downloaded from ProjectorsManual.com Manuals
18
B
Problem
Solution
Result
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Lamp must be replaced (see page 35)
lamp door
Lamp light
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call us.
Check out our HOW TO section there for additional information on using this
projector for home theater or gaming applications. See the Quick Start Poster/
Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be
purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a
professional packaging company pack the unit. Please insure your shipment for its
full value.
Downloaded from ProjectorsManual.com Manuals
19
Lamp turns on
Startup
Screen
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
•
Auto Image button to resynch the projector to the source
•
Resize button to switch among aspect ratios (see page 26).
•
Help button to get help with connecting sources and improving the picture.
Troubleshooting the remote
Caution:
•
•
•
•
When replacing the batteries, be aware that using batteries other than the
type provided with the projector may risk severe damage to the remote.
When disposing of the batteries, be sure to do so in an enviromentally proper
manner.
If the remote control gets wet, wipe it dry immediately.
•
Avoid excessive heat and humidity.
•
Ensure the batteries' polarity (+/-) is aligned correctly.
•
Do not mix new and old batteries together, or mix different types of batteries together.
•
Replace the batteries as soon as they run out.
•
Remove batteries from the remote control when storing or not in use for a
prolonged period.
navigation
buttons
To operate, point the remote at the front of the projector (not at the computer).
The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 12 for
shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
values in the menus. See page 25 for more info on the menus.
The remote also has:
•
•
•
•
•
•
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank Screen or
Freeze (see page 28).
Source button to switch between sources.
Blank button to blank the screen.
Presets button to select stored settings (see page 26).
Downloaded
from
ProjectorsManual.com
Manuals
Mute button to
silence
the audio.
Make sure the batteries are installed in the proper orientation and are not
dead.
Make sure you’re pointing the remote at the projector or the screen, not the
computer, and are within the remote range of 15 feet (4.5m). For best
results, point the remote at the projector.
20
Using the audio
connect audio cable
Using the projector’s speakers
When using the HDMI connector, both audio and video are sent over the cable to
the projector and audio will play from the projector's speakers.
For inputs other than HDMI, connect the audio source to the Audio In connector
to hear audio through the projector's speakers.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
•
•
•
•
adjust volume
Make sure the audio cable is connected to the Audio In connector on the
projector, and that the other end of the cable is connected to an “audio out”
connector on the source (not a “line-in” or “microphone” connector).
Make sure the volume is turned up enough. Press the Volume button on the
keypad or remote.
Make sure the correct source is active.
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
Downloaded from ProjectorsManual.com Manuals
21
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of
their functions:
Power–turns the projector on and off (page 8).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 26).
Keystone–adjusts squareness of the image (page 9).
Menu–opens the on-screen menus (page 25).
Select–confirms choices made in the menus (page 25).
menu navigation
buttons
Up/Down arrows–navigates to and adjusts settings in the menus (page 25).
Volume–adjusts sound (page 21).
Source–changes the active source (page 8).
Downloaded from ProjectorsManual.com Manuals
22
Optimizing computer images
Presentation features
After the projector is running and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see
page 25.
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
•
•
•
•
•
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
(page 26).
Change the Aspect Ratio. Choose the option that best fits your input source
(page 26).
Adjust the Color Temperature in the Advanced Picture menu (page 26).
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced Picture menu (page 27).
Once you have optimized the image for a particular source, you can save the
settings using Presets. This allows you to quickly recall these settings later
(page 26).
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Software User's Guide for information about optimizing
images.
•
•
Downloaded from ProjectorsManual.com Manuals
23
The Custom key allows you to assign various features to the button. The
default effect is Source Info, which displays information about the projector
and current source. See page 28 for details.
The Search Screen option lets you change the appearance of the blank screen
and start up screen (page 29).
Two options, Auto Off and Screen Save Time, are provided to automatically
shut down the projector after several minutes of inactivity or display a black
screen. This helps preserve lamp life (page 28).
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the screen, you
can optimize the image using the onscreen menus. For general information on
using the menus, see page 25.
You can customize the projector for your specific setup and needs. See page 28 to
page 29 for details on these features.
•
•
•
•
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic Picture
menu (page 26).
Change the Aspect Ratio. Choose the option that best fits your input source
(page 26).
Select a Sharpness setting (page 26).
Adjust the Color Temperature. Select a listed warmth value (page 27).
Turn on Overscan to remove noise on the edges of the image (page 27).
•
•
•
•
•
•
•
•
•
Downloaded from ProjectorsManual.com Manuals
24
For rear projection, turn Rear Project on in the Setup menu.
For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
Specify which source the projector checks first for active video during powerup.
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The menus
automatically close after 60 seconds if no buttons are pressed.) Use the arrow
buttons to move up and down to highlight the desired menu, then press the Select
button.
To change a menu setting, highlight it, press Select, then use the up and down
arrow buttons to adjust the value or select an option or turn the feature on or off.
Press Select to confirm your changes. Use the arrows to navigate to another
setting. When your adjustments are complete, press Menu to access a different
menu; press the Menu button at any time to navigate to the higher-level menu and
ultimately close the menus.
The menus are grouped by usage:
•
•
•
•
The Basic Picture menu provides common image adjustments.
The Advanced Picture menu provides more complex image adjustments.
The Setup menu provides set-up type adjustments that are not changed often.
The Status and Service menu provides information about the projector and
source.
Downloaded from ProjectorsManual.com Manuals
25
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the up and
down arrows to adjust the values, then press Select to confirm the changes.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest parts
of the picture and changes the amount of black and white in the image.
Sharpness: (video sources only) changes the clarity of the edges of a video image.
Select a sharpness setting.
Color: adjusts a video image from black and white to fully saturated color. The
color setting applies to video sources only.
Basic Picture menu
Tint: adjusts the red-green color balance in the image of NTSC video images. The
tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
For more information regarding Aspect Ratio, see page 10.
Apply Preset...: Presets are provided that optimize the projector for displaying
computer presentations and video images under certain conditions.
There is also a user-definable preset. To set this preset, adjust the image and select
Save User in the Presets menu. You can recall these settings in the future by
selecting the User preset.
Aspect ratio
Keystone: adjusts the image vertically and makes a squarer image. You can also
adjust keystone from the keypad.
Digital Zoom: changes the size of projector’s display area. If the display area has
been resized by this setting, it can be moved by changing the Horz Shift and Vert
Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its size has
been changed by the Digital Zoom setting.
increasing keystone
Downloaded from ProjectorsManual.com Manuals
26
decreasing keystone
Advanced Picture menu
BrilliantColor™: produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images. Choose Normal Look for
most video sources and Bright Look for most computer sources.
White Peaking: increases the brightness of whites that are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed relative
warmth value.
Force wide: when this is off, the analog locking algorithms choose the standard
mode resolution (4:3) as the preferred default resolution. When this is on, the
analog locking algorithms choose wide mode resolution (16:10) as the preferred
default resolution.
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a DVD
player, is not syncing properly with the projector, select this option to help it to
sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Color Space: applies to computer and component video sources. It allows you to
select a color space that has been specifically tuned for the input signal. When
Auto is selected, the projector automatically determines the standard. To choose
a different setting, turn off Auto, then choose RGB for computer sources or
choose either REC709 or REC601 for component video sources.
Gamma: select the appropriate gamma from among Video, Film, Bright, and CRT.
Horizontal/Vertical Position: adjusts the position of a computer source.
Advanced Picture menu
Downloaded from ProjectorsManual.com Manuals
27
Setup menu
Auto Source: When this feature is On, the projector automatically finds the active
source, checking the selected Power-up Source first. When this feature is Off, the
projector defaults to the source selected in Power-up Source. To display another
source, you must manually select one by pressing the Source button on the
remote or keypad.
Language: allows you to select a language for the onscreen display.
Key Click: turns the key click sound on or off. When this setting is on, pressing
keys on the keypad causes the projector’s speaker to play a “click” sound.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and press Select
to choose a different one.
•
Source Info: the default action. Shows the Source Info menu.
•
Projector Info: shows the Projector Info menu.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 10 and page 26).
•
Auto Image: resets the projector to the source (page 22).
•
Overscan: removes noise around the image.
•
Blank Screen: displays an empty screen.
•
Freeze Screen: pauses the projected image.
•
Mute: turns off all sound.
•
Source: cycles through available sources.
Blank Key: select what to display when the blank key on the remote is pressed:
your custom snapshot, a solid color screen (blue, black or white), the factory logo
screen, a timer, or test patterns. The timer option is useful for classroom tests or
break times during meetings.
Setup menu
Power-up Source: determines which source the projector checks first for active
video during power-up.
DisplayLink Source: allows you to disable DisplayLink (project over USB). When
Off, you won’t be prompted to install DisplayLink software when you connect the
USB cable to your computer.
HDMI DDC: When this feature is set to On, the projector will support an older
DVD player for HDMI port.
AC Power On: When this feature is on, the projector automatically turns on when
electrical power is connected. This allows control of ceiling mounted projectors
with a wall power switch.
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors may not look right
or the image may appear “torn.” If this happens, manually select a video standard
by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Auto Off Time: automatically turns the projector off after no signals are detected
for a preset number of minutes. If an active signal is received before the projector
powers down, the image will be displayed.
Screen Save Time: automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns when an
active source is detected or a remote or keypad button is pressed.
Closed Captions: controls closed caption display while audio is not muted. If this
setting is not off, and audio is not muted, and the source is NTSC and contains
captions on the selected channel, then the projector must display caption text
overlaid on the image.
Lamp Low Power: toggles between on and off. Turn it on to lower the light output
of the lamp. This also lowers the fan speed, making the projector quieter.
Power Sounds: controls whether the projector makes a sound when powered on
and off.
Downloaded from ProjectorsManual.com Manuals
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
28
Rear Project: reverses the image so you can project from behind a translucent
screen.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new
PIN. You can navigate between OK and Cancel by pressing the up and down
buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify
the new PIN.
Auto Keystone: automatically adjusts vertical image.
Prevent PC Screen Saver: prevents your computer from going into Screen Save
mode. The projector must be connected to the PC via a USB cable for this feature
to work.
If you lose or forget your custom PIN:
Search Screen: allows you to display a blank screen instead of the default screen at
startup, and when no source is detected.
Contact InFocus support. Go to www.infocus.com/support
Serial Port, Baud Rate: selects the serial port and baud rate.
Take Snapshot...: captures the current image and allows it to be used as the search
screen image.
Serial Port Echo: controls whether the serial port echoes characters.
Disable Snapshot: allows the user to disable the snapshot capability.
Show Messages: displays status messages (such as “Searching”) in the lower-left
corner of the screen.
Menu Offset: allows you to change the position of the On Screen Display items.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image behind
the menu is visible.
Magnify Controls: determines whether the select key can be used to change
magnify settings when the OSD menu is not visible.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you must
enter the PIN before you can project an image. The default PIN on this projector
is Menu-Up-Down-Select-Source. Use the navigation buttons on the remote or
keypad to enter the correct 5-button press sequence. When all 5 numbers are
entered correctly, press the Select button on the remote or keypad to select OK.
If the message “Wrong PIN” appears, verify the code and re-enter it. If you misenter a number, you must enter 5 numbers and press the Select button in order to
access the “Wrong PIN” message and re-enter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup
screen. Enter the PIN. Use the navigation buttons on the remote or keypad to
enter the correct button press sequence. See the description above for
instructions.
Downloaded from ProjectorsManual.com Manuals
29
Status and Service menu
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info menu
to zero. Do this only after changing the lamp.
Factory Reset: restores all settings to their default.
Service Code: only used by authorized service personnel.
Status and Service menu
Downloaded from ProjectorsManual.com Manuals
30
Using LitePort (IN1503 only)
To start the slide show: While viewing thumbnails, press the arrow buttons to
highlight a thumbnail, then press the Select button to start the slide show at the
highlighted image.
LitePort displays a slide show of JPEG images stored on a USB flash drive
connected to the projector. This feature can eliminate the need for a computer
source.
To change the image during the slide show: Press the Down or Right button to go
to the next image, or press the Up or Left arrow button to go to the previous
image (the slide show may also advance automatically depending on the value of
the Next Slide setting; see the LitePort Menu section below for details).
Image File Types
LitePort displays image files in JPEG format only (file extensions .JPEG and .JPG).
Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are ignored.
To change to a different folder: While viewing thumbnails, press the arrow buttons
to highlight the desired folder icon, then press the Select button (to go to the
higher-level folder, select the folder icon labeled "Up").
Viewing a Slide Show
To view your pictures as a slide show, follow these steps:
To change LitePort settings: Press the Menu button during the slide show, or while
viewing thumbnails (see the LitePort Menu section below for details).
1 Connect a USB flash drive to your computer and copy JPEG files from your
computer to the USB flash drive.
Using the LitePort Menu
2 Turn on your projector if needed.
To show the LitePort menu, press the Menu button on the keypad or remote
during the slide show, or while viewing thumbnails. To highlight a menu item, press
the arrow buttons. Then to do the action or change the setting, press Select. To
remove the menu, press the Menu button again.
3 Remove the USB flash drive from your computer and plug it into the LitePort
connector on the rear of the projector.
4 The projector will start a slide show of the images found (if you see image
Rotate Picture: Rotates the current image by 90 degrees clockwise (rotation is
temporary; the image returns to its original orientation when the USB flash drive is
removed from the projector or when the projector is turned off).
thumbnails instead, see To Start the Slide Show section below).
5 To go to the next image in the slide show, press the Down or Right arrow
button on the projector keypad or remote. To go to the previous image, press
the Up or Left arrow button.
Stop/Start Slideshow: Stops the slide show, or starts it at the selected thumbnail
(when the menu is not visible, you can also stop or start the slide show by pressing
the Select button).
Controlling LitePort
Go to Projector Main Menu: Removes the LitePort menu and displays the
projector's main menu, where you can adjust the picture or change other
projector settings.
When you plug a USB flash drive into the projector's LitePort connector, the
projector will scan the drive and then either start a slide show or show image
thumbnails.
To stop the slide show and view thumbnails: Press the Select button during the
slide show. In Thumbnails view, the name of the current folder, the current image
number, and the total number of images in that folder are shown at the bottom of
the screen. While viewing thumbnails, press the arrow buttons to scroll through
the thumbnails, or press Select when an image is highlighted to start the slide
show,
or press Select
when
a folder is highlighted to
open that folder.
Downloaded
from
ProjectorsManual.com
Manuals
(For remaining items below, highlight the setting, then press Select one or more
times to change the setting value.)
31
Auto Start: Select On to have the player start the slide show when the USB flash
drive is first connected. Select Off to have the player display thumbnails when the
USB flash drive is first connected.
window.
5 Point to Save As, then click Other Formats.
Show All Folders: Select On to have the slide show display all images in all folders.
Select Off to have the slide show display images only from the current folder.
6 In the Save As dialog box, click the Save as type drop-down menu. Scroll
Fill Screen: Select On to have the slide show expand small images to fill the screen.
Select Off to have the slide show display small images at their original size.
7 Make sure the contents of your USB flash drive are visible in the Save As dialog
through the menu and select JPEG File Interchange Format.
box before you continue - to view your USB flash drive in the Save As dialog
box, first click My Computer, then double-click the USB flash drive's icon
(make sure you do both of these in the Save As dialog box, not on your
computer's desktop).
Next Slide: Select Manual to disable automatic slide advance in the slide show.
Select other values to make the slide show advance to the next image
automatically (regardless of this setting, manual advance is always available by
pressing the arrow buttons).
8 Click Save. PowerPoint will ask if you want to export every slide or only the
Effect: Select Off to have no transition effect when changing between images
during the slideshow. Select Random to use a different random effect for each
transition. Select other values to use a specific effect.
current slide; click Every Slide. PowerPoint will save each slide in your
presentation as a separate JPEG file. These files are saved in a new folder that
has the same name as the original document.
Show Info: Select On to show the name of the current file and folder, the current
image number, and the total number of images in the slide show at the bottom of
the screen. Select Off to hide this information.
9 Remove the USB flash drive from your computer and plug it into the
projector's LitePort connector.
10 On the projector, navigate to the folder created in step 8 and then start the
Displaying PowerPoint Slides
slide show (for instructions on navigating and controlling the slide show, see
the Controlling LitePort section above).
Follow the steps below to display PowerPoint slides using LitePort (these
instructions apply to PowerPoint 2007 in Windows; for other presentation
programs refer to the program's instructions or help file for the steps needed to
save a presentation as separate JPEG files):
NOTE: PowerPoint embedded videos, transition effects, and animations are not
included when saving as JPEG. However, you can select a LitePort slideshow
transition effect by changing the Effect in the LitePort menu.
1 Connect the USB flash drive to your computer.
2 Open your PowerPoint document.
3 This step is optional but improves image quality: Click the Design tab near the
top of the PowerPoint document window, then click Page Setup. Click the
Slides sized for drop-down menu and select Custom. Change both Width and
Height to double their previous values, then click OK.
4 Click the Office button in the upper left corner of the PowerPoint document
Downloaded from ProjectorsManual.com Manuals
32
Troubleshooting LitePort
•
If images load slowly: Make sure you are using a newer USB 2.0compatible (high speed) USB flash drive. Larger image file sizes may also slow
down the player; to reduce file size, use an image editing program on your
computer to resize images smaller; for the best balance between image
quality and speed, resize images to be 1024 pixels wide.
•
If no images are found, or some images are not shown, or you only see folder
thumbnails but no images: Make sure that images are JPEG file type (file
extensions .JPEG and .JPG); other file types are not supported and will be
ignored.
•
If you see a blank screen, or a logo, or the wrong input source (computer,
video, etc.) instead of your images: Keep pressing the Source button on the
keypad or remote until the LitePort message is displayed (if you still don't see
any images, make sure the USB flash drive is correctly and completely plugged
into the projector's LitePort connector).
•
If nothing happens when you connect your USB flash drive, and you cannot
select the LitePort input source as described above: Check the format of your
USB storage device. LitePort only supports USB storage devices formatted as
FAT32. Devices formatted as NTFS, and non-storage devices (such as
cameras) are not supported.
•
If images saved by PowerPoint are low quality: Make sure to do step 3 when
following the steps in the Displaying PowerPoint Slides section above.
Downloaded from ProjectorsManual.com Manuals
33
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals
might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any part of
the projector.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing
covers may expose you to dangerous voltage and other hazards. Refer all
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the
information that came with the lock for instructions on how to use it.
security
lock
Downloaded from ProjectorsManual.com Manuals
34
Replacing the projection lamp
Hg – Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org.
The Lamp Hours timer in the Projector Info menu counts the number of hours the
lamp has been in use. Twenty hours before the lamp life expires, the message
“Replace lamp” appears on the screen at startup.
•
NOTE: Be sure to use the InFocus lamp module designed for this projector.
You can order new lamps from www.infocus.com (in select areas), your
retailer or your dealer. Only genuine InFocus lamps are tested for use in this
projector. Use of non InFocus lamps may cause electrical shock and fire, and
may void the projector warranty. InFocus is not liable for the performance,
safety or certification of any other lamps.
WARNINGS:
•
•
•
•
•
•
•
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
To avoid burns, allow the projector to cool for at least 60 minutes before you
replace the lamp.
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can obscure
projection sharpness and may cause the glass to shatter.
Be extremely careful when removing the lamp housing. In the unlikely event
that the lamp ruptures, small glass fragments may be generated. The lamp
module is designed to contain most of these fragments, but use caution when
removing it.
Before replacing a ruptured lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
Downloaded from ProjectorsManual.com Manuals
35
1 Turn off the projector and unplug the power cord.
turn off and unplug
projector
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Remove the lamp door by (a) removing the screw on the side of the lamp
door, (b) lifting the door off.
4 Loosen the captive screw that attaches the lamp housing to the projector.
Carefully remove the lamp housing. Dispose of the lamp in an environmentally
proper manner.
5 Install the new lamp housing and tighten the screw.
6 Re-attach the lamp connector to the projector.
(a)
7 Replace the lamp door by sliding it into place.
8 Plug in the power cord and press the Power button to turn the projector back
(b)
on.
9 To reset the lamp hour timer, navigate to the Status and Service menu and
select Reset Lamp Hours. See page 30 for details.
loosen screw
Downloaded from ProjectorsManual.com Manuals
36
wait 60 minutes
INDEX
D
DVDs 28
F
Factory Reset 32
Focus 11
Force wide 29
Freeze Screen 30
G
Gamma 29
H
HDMI 1.3 connection 13
HDMI DDC 30
HDTV 6, 28
Horizontal 29
I
Image
size 5
optimization 25
K
Key Click 30
Keypad buttons 24
Keystone 28
keystone, adjusting 11
L
Lamp hours, resetting 35
Lamp Low Power 30
Language 30
Laptop video port activation 10
LEDs 14
Leveling foot 11
LitePort
M
Maintaining the projector 33
Menu button 27
Menu usage 27
Mute 30
O
Optimizing images 25
Optimizing video 26
Overscan 29, 30
Numerics
16x9 vs 4x3 12
5 volt DC output 4
A
AC Power On 30
Advanced menu 29
Apply Preset 28
Aspect Ratio 12, 28, 30
Audio In Computer connector 9
Audio In connector 13
Auto Image 30
Auto Off Time 30
Auto Source 30
B
Blank Key 30
Blank Screen 30
Brightness 28
BrilliantColor 29
C
Cable box 12
Ceiling Mount 30
Cleaning the lens 33
Closed Captions 30
Color Space 29
Color Temperature 29
Computer In connector 9
Connecting
external speakers 23
computer 9
video device 12
Connector on Projector 7, 8
Connector panel 4
Contacting InFocus 21
Contrast 28
Custom Key 30, 25
Customer service contact information 21
Customizing the projector 26
Downloaded from ProjectorsManual.com Manuals
37
P
Phase 29
Picture menu 28
Power connector 9
Power cord 9
Power Sounds 30
Power-up Source 30
Presentation features 25
Projection distance 5
Projector
connector panel 4
customization 26
image Size 5
keypad buttons 24
maintenance 33
menus 27
offset 5
registering 3
security lock 33
status indicator panel 14
connecting computers 9
connecting video devices 12
positioning 5
setting up 5
shutting down 14
troubleshooting problems 14
Projector Info 30
R
Rear 31
Registering your projector 3
remote control 22
Reset 32
Resetting the projector 32
RS-232 4
S
Safety Considerations 2
Screen Aspect 12
Screen Save 14, 30
Search Screen 31
Security
lock 33 from ProjectorsManual.com Manuals
Downloaded
Service 32
Service Code 32
Sharpness 28
Shutting down the projector 14
Source 30
Source Info 30
Status indicator panel 14
Sync Threshold 29
T
Tint 28
Tracking 29
Troubleshooting 14
TV tuner 12
U
USB 4, 9
V
Vertical 29
video optimizing 26
Video Standard 30
Volume button 23
W
Warranty 21
White Peaking 29
Z
Zoom 11
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement