LG PF80A Projector User Guide

LG PF80A Projector User Guide
Owner's Manual
Please read the safety information carefully before using the product.
PF80A
Downloaded from www.Manualslib.com manuals search engine
2
LICENSE
LICENSE
Manufactured under license from Dolby Laboratories. Dolby and
the double-D symbol are trademarks of Dolby Laboratories.
ABOUT DIVX VIDEO: DivX® is a digital video format created
by DivX, LLC, a subsidiary of Rovi Corporation. This is an
official DivX Certified® device that has passed rigorous testing
to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX
videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play purchased DivX
Video-on-Demand (VOD) movies. To obtain your registration
code, locate the DivX VOD section in your device setup menu.
Go to vod.divx.com for more information on how to complete
your registration.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks
of Rovi Corporation or its subsidiaries and are used under
license.
Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
For DTS patents, see http://patents.dts.com. Manufactured
under license from DTS Licensing Limited. DTS, the Symbol,
& DTS and the Symbol together are registered trademarks,
and DTS 2.0+Digital Out is a trademark of DTS, Inc. © DTS,
Inc. All Rights Reserved.
This device meets the EMC requirements for home appliances (Class B) and is
intended for home usage. This device can be used in all regions.
NOTE
yyImage shown may differ from your projector.
yyYour projector’s OSD (On Screen Display) may differ slightly from that shown in
this manual.
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
3
SAFETY INSTRUCTIONS
Please take note of the safety instructions to prevent any potential accident or misuse
of the projector.
yySafety precautions are given in two forms, i.e. Warning and Caution as detailed below.
WARNING: Failure to follow the instructions may cause serious injury and even death.
CAUTION: Failure to follow the instructions may cause injury to persons or damage to
the product.
yyRead the owner's manual carefully and keep it at hand.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING/CAUTION
The
lightning flash with
RISK OF ELECTRIC SHOCK
arrowhead
symbol, within
DO NOT OPEN
an equilateral triangle, is
intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE
AND ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
Downloaded from www.Manualslib.com manuals search engine
4
SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Indoor Installation
WARNING
yyDo not use the projector outside and
do not expose the product to any
humidity or water.
- Since the product is not waterproof,
this may result in a fire or electric
shock.
yyDo not place the projector in direct
sunlight or near heat sources such as
radiators, fires, stoves, etc.
- This may result in fire.
yyDo not place flammable materials
such as aerosols near the projector.
- This may result in fire.
yyDo not allow children to cling to or
climb up to the projector.
- This may cause the projector to fall,
causing injury or death.
yyDo not install the product in a place with
no ventilation (e.g., on a bookshelf or in
a closet) or on a carpet or cushion.
- This may result in fire due to the
increase in internal temperature.
yyDo not place the product close to
sources of steam, oil, or oil mist, such
as humidifiers and kitchen counters.
- Failure to do so may result in fire,
electric shock, or corrosion.
yyDo not install the product onto a wall
or ceiling that is close to sources of
oil or oil mist.
- The product may be damaged and
fall, resulting in serious injury.
Downloaded from www.Manualslib.com manuals search engine
yyDo not place the projector where it
might be exposed to dust.
- This may result in fire.
yyDo not use the projector in a damp
place such as a bathroom where it is
likely to get wet.
- This may result in fire or electric
shock.
yyDo not allow a tablecloth or curtain to
block the air vent.
- This may result in fire due to the
increase in the internal temperature.
yyEnsure good ventilation around the
projector. The distance between the
projector and the wall should be at
least 30 cm.
- This will prevent fire due to the
increase in the internal temperature.
CAUTION
yyWhen placing the projector on a table
or shelf, be careful not to put it near
the edge.
- ������������������������������������
The
�������������������������������������
projector could fall due to balance problems, which may cause
personal injury or damage to the
product. Make sure to use a projector cabinet or stand that fits the
projector.
yyWhen moving the projector, make
sure to switch it off and remove the
power plug and cords.
- The power cord may be damaged,
resulting in fire or electric shock.
yyDo not place the projector on an
unstable or vibrating surface such as
a wobbly shelf or a slope.
- It may fall and cause injury.
SAFETY INSTRUCTIONS
yyBe careful not to tip the projector over
when connecting external devices to
the projector.
- This may cause personal injury or
damage to the projector.
Power
WARNING
yyThe grounding wire should be connected.
- Ensure that you connect the grounding cable to avoid electric shock.
If it is not possible to ground the unit,
have a qualified electrician install a
separate circuit breaker.
Do not try to ground the projector
by connecting it to telephone wires,
lightning rods, or gas pipes.
yyThe power plug should be inserted
fully into the power outlet.
- An unstable connection may cause
a fire.
yyDo not place heavy objects on the
power cord.
- This may result in fire or electric
shock.
yyNever touch the power plug with wet
hands.
- This may result in electric shock.
yyDo not plug too many devices into
one multi-power outlet.
- This may result in fire due to the
power outlet overheating.
yyPrevent dust from collecting on the
power plug pins or outlet.
- This may result in fire.
yyTo turn off the main power, remove
the power plug, which should be
positioned so it is easy to access for
operation.
Downloaded from www.Manualslib.com manuals search engine
5
CAUTION
yyHold the plug firmly when unplugging.
- A damaged wire may create a fire
hazard.
yyEnsure the power cord and plug are
not damaged, modified, severely
bent, twisted, pulled, sandwiched,
or hot. Do not use the product if the
power outlet is loose.
- This may result in fire or electric shock.
yyKeep the power cord away from heating
devices.
- The wire's sheath may melt, which
may result in fire or electric shock.
yyPlace the projector where people will
not trip over or walk on the power
cord to protect the power cord and
plug from any damage.
- This may result in fire or electric shock.
yyDo not turn the projector on or off by
plugging in the power plug or unplugging it from the power outlet.
(Do not use the power plug as a switch.)
- This may result in electric shock or
damage to the product.
yyDo not insert a conductor into the other
side of the wall outlet while the power
plug is inserted into the wall outlet.
In addition, do not touch the power
plug immediately after it is disconnected
from the wall outlet.
- This may result in electric shock.
yyUse only the official power cord which
is provided with the product. Do not
use other power cords.
- This may result in fire or electric
shock.
6
SAFETY INSTRUCTIONS
When in Use
WARNING
yyDo not place anything containing
liquid on top of the projector such as
a vase, flower pot, cup, cosmetics,
medicine, ornaments, candles, etc.
- This may result in fire or electric
shock, or cause injury due to falling.
yyIn the event that there is a heavy
impact or the cabinet is damaged,
switch it off, unplug it from the power
outlet and contact an authorized service center.
- This may result in electric shock.
yyDo not insert pieces of metal such
as coins, hairpins, metal debris, or
flammable materials such as paper or
matches into the projector.
- This is to prevent electric shock or fire.
yyIn the event that liquid or a foreign
object falls into the projector, switch it
off and unplug it from the power outlet
and contact our service center.
- This may result in fire or electric
shock.
yyMake sure that a child does not swallow the batteries when you replace
the old remote control batteries with
new ones. Keep batteries out of reach
of children.
- If a child swallows a battery, consult
a doctor immediately.
yyNever open any cover on the projector.
- There is a high risk of electric shock.
yyDo not look directly into the lens
when the projector is in use.
- The bright light may damage your
eyes.
Downloaded from www.Manualslib.com manuals search engine
yyWhen the lamp is on or has just been
turned off, avoid touching the air vent
or lamp, because these will be very hot.
yyIf there is a gas leak in the room with
the projector, do not touch the projector
or power outlet. Open the windows
for ventilation.
- Sparks may cause fire or burns.
yyUnplug the power cord from the outlet
during a lightning storm.
- This will prevent shock or damage
to the projector.
yyDo not use the projector near
electronic devices that generate a
strong magnetic field.
yyDo not put the plastic bag used to
pack the projector around your head.
- This may cause suffocation.
yyDo not keep your hand on the projector
for a long time when it is running.
yyWhen you play a game by connecting
a game console to a projector, it is
recommended that you maintain a
distance of more than four times the
diagonal length of the screen.
-M
ake sure that the connecting cable is
long enough. Otherwise, the product
may fall causing personal injury or
damage to the product.
yyDo not place the projector or its
remote control with battery in
an extremely high temperature
environment.
- This may result in fire.
SAFETY INSTRUCTIONS
CAUTION
yyDo not place heavy objects on the
projector.
- It may fall down and cause personal
injury.
yyBe careful not to allow any impact to
the lens during transport.
yyDo not touch the lens of the projector.
- The lens may be damaged.
yyDo not use any sharp tools on the
projector such as a knife or hammer,
because this may damage the casing.
yyIn the event that no image appears
on the screen or no sound is heard,
stop using the projector. Switch off the
projector, unplug it from the power outlet, and contact our service center.
- This may result in fire or electric shock.
yyDo not drop anything onto
the projector or allow anything to
bang into the projector.
- This may cause damage to the projector
or personal injury.
It
yy is recommended that you maintain
a distance of more than 5 - 7 times
the diagonal length of the screen.
- If you watch the screen at a close
distance for a long time, your eye
sight may become worse.
yyDo not block the light beam emitted
from the projector using a book or
other object.
- Lengthy exposure to the projector
beam may result in fire. In addition, the
lens may be overheated and damaged
by the reflected heat. Disable the AV
function to stop projection temporarily
or turn off the power.
yyDo not start the projector with the
volume turned up high.
- High volume may damage hearing.
Downloaded from www.Manualslib.com manuals search engine
7
Cleaning
WARNING
yyDo not spray the projector with
water when cleaning. Make sure water
does not flow into the projector.
- This may result in fire or electric
shock.
yyWhen there is smoke or a strange
smell coming out from the projector or
a foreign object falls into the pro­jector,
please switch it off, unplug it from the
power outlet, and contact our service
center.
- Otherwise, this may result in fire or
electric shock.
yyUse air spray, a soft cloth, or a cotton
swab moistened with a lens cleaning
chemical or alcohol to remove dust or
stains on the front projection lens.
CAUTION
yyContact your seller or our service
center once a year to clean the internal parts of the projector.
- If you do not clean the projector for
a long period of time, dust will
accumulate, which may result in fire
or damage to the projector.
yyWhen cleaning plastic parts such as
the projector case, unplug the power
first and wipe with a soft cloth. Do not
spray with water or wipe with a wet
cloth. Never use glass cleaner, automobile or industrial shiner, abrasives,
wax, benzene, or alcohol as these
can damage the projector.
- This can result in fire, electric shock
or cause damage to the product
(deformation and corrosion).
8
SAFETY INSTRUCTIONS
yyRemove the plug from the outlet
before cleaning the product.
- Otherwise, this may result in electric
shock.
Others
WARNING
yyWhen you go out, place the projector
out of reach of animals, and remove
the power plug from the wall outlet.
- Using a damaged power cord may
result in short circuit or fire.
yyDo not use the projector near highprecision electronic devices or those
that transmit weak radio signal.
- This may affect the operation of the
product, causing an accident.
yyOnly a qualified technician can
disassemble or modify the projector.
For diagnosis, adjustment, or repair,
contact your seller or our service
center.
- This may result in fire or electric
shock.
yyDo not stare directly into lens when in
operation, eye damage can occure.
yyNo user serviceable parts inside unit.
High voltage parts can cause shock
and even electrocution.
yyProper ventilation required, do not
block airflow around unit. Doing
so can cause injury and internal
overheating.
yyTo prevent damage to lamp, unit must
remain plugged in for approximately 3
minutes after power down to allow for
proper cool down (not applicable on
LED models).
Downloaded from www.Manualslib.com manuals search engine
yyDo not touch the lens; doing so can
result in burns or damage to lens.
Lens and unit may be HOT during
and immediately after use. Use
caution when handling unit, allowing
for proper cool down.
yyOnly use a grounded electrical outlet.
yyDo not insert anything into or cover
up the exhaust vents.
-This may result in fire or electric
shock.
yyFollow all maintenance guidelines
for optimal use; service only at an
authorized service center.
yyLamp contains mercury and as such
must be disposed of according to
local, state and federal laws (not
applicable on LED models).
CAUTION
yyDo not mix new batteries with old
ones.
- Burst or leaking batteries may result
in damage or injury.
yyBe sure to unplug if the projector is not
to be used for a long period.
- Accumulated dust may result in fire or
electric shock due to overheating, ignition, or poor insulation.
yyOnly use the specified type of battery.
- Burst or leaking batteries may result in
damage or injury.
yyDo not charge the battery using any
devices other than the one provided with
the product.
- This may result in damage to the
battery or fire.
SAFETY INSTRUCTIONS
yyDispose of used batteries properly.
-This may result in explosion or fire. The
correct method of disposal may vary
depending on your country or region.
Dispose of the battery pack
as instructed.
yyDo not throw away or disassemble the
battery.
- This may result in fire or explosion
due to damage to the battery.
yyStore batteries away from metallic
objects, such as keys and paper clips.
- Excess current may cause a rapid
increase in temperature, resulting in
fire or burns.
yyDo not store the batteries near any
heat source, such as a heater.
- This may result in fire or damage to
the product.
yyDo not store batteries at temperatures
higher than 60 °C or in high humidity.
- This may result in explosion or fire.
yyKeep the batteries and remote out of
reach of children.
- This will prevent personal injury or
damage to the product.
yyMake sure that the battery is installed
correctly.
- This prevent explosion or fire.
yyThe battery contains lithium-ion, so it
must be handled with care.
- This may result in explosion or fire.
yyMake sure you use the same type of
batteries for replacement.
yyIncorrect battery replacement may
cause fire.
Downloaded from www.Manualslib.com manuals search engine
Risk Group 2
CAUTION: Hazardous optical
radiation may be emitted from this
product. Do not stare into the lens at
the operating lamp. It may be harmful
to your eyes.
9
10
SAFETY INSTRUCTIONS
FCC NOTICE
Federal Communications
Commission (FCC) Statement
You are cautioned that changes or
modifications not expressly approved
by the part responsible for compliance
could void the user’s authority to operate
the equipment.
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to
part 15 of the FCC rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
-R
eorient or relocate the receiving
antenna.
- Increase the separation between the
equipment and receiver.
-C
onnect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
-C
onsult the dealer or an experienced
radio/projector technician for help.
Downloaded from www.Manualslib.com manuals search engine
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any
interference received, including
interference that may cause undesired
operation of the device of the device.
FCC Caution
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user's authority to operate this
equipment and for indoor use only, use
outdoors or in other modes not covered
by this manual may violate the FCC
regulation and violate the user authority
to use the product.
Specially, within the 5.15-5.25 GHz
band, U-NII device is restricted to indoor
operations to reduce any potential for
harmful interference to co-channel MSS
operations.
FCC RF Radiation Exposure
Statement:
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment. This
equipment should be installed and
operated with minimum distance 20
cm (7.8 inches) between the radiator
and your body. End users must follow
the specific operating instructions for
satisfying RF exposure compliance.
SAFETY INSTRUCTIONS
IC (CANADA)
Industry Canada Statement:
This device complies with RSS-210 of
the Industry Canada Rules. Operation is
subject to the following two conditions:
1) this device may not cause
interference and
2) this device must accept any
interference, including interference
that may cause undesired operation
of the device.
Avis d’Industrie Canada :
Cet appareil est conforme à la norme
CNR-210 des règlements d’Industrie
Canada. Son fonctionnement est sujet
aux deux conditions suivantes :
1) Cet appareil ne doit pas provoquer
d’interférences et
2) Cet appareil doit accepter toutes
les interférences, y compris
celles pouvant entraîner son
dysfonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC
radiation exposure limits set forth for an
uncontrolled environment.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR
Projector INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE
THE EQUIPMENT.
Downloaded from www.Manualslib.com manuals search engine
Avis d’Industrie Canada sur
l’exposition aux rayonnements
Cet appareil est conforme aux limites
d’exposition aux rayonnements
d’Industrie Canada pour un
environnement non contrôlé.
REMARQUE : LE FABRICANT
N’EST PAS RESPONSABLE
DES INTERFÉRENCES
RADIOÉLECTRIQUES CAUSÉES
PAR DES MODIFICATIONS NON
AUTORISÉES APPORTÉES À
CET APPAREIL. DE TELLES
MODIFICATIONS POURRAIT
ANNULER L’AUTORISATION
ACCORDÉE À L’UTILISATEUR DE
FAIRE FONCTIONNER L’APPAREIL.
11
12
CONTENTS
CONTENTS
LICENSE
2
SAFETY INSTRUCTIONS
3
PREPARATION
14
Accessories
14
Optional Extras
15
Parts and Components
-- Front
-- Back
16
16
17
Installation
18
-- Installation Precautions
18
-- Projection Distance per Screen Size 19
-- How to Install the Projector On a Tripod
20
-- Kensington Security System
20
REMOTE CONTROL
21
USING THE PROJECTOR
23
Watching Projector
-- Initial Setup
-- Focus of the Screen Image
23
23
24
Additional Options
-- Adjusting Aspect Ratio
-- Using the Keystone Function
-- Changing Input Device
-- To use SIMPLINK
25
25
25
26
26
Using the Quick Menu
28
To Set Sound
29
-- To Set Sound Output
29
-- To Connect and Use a Bluetooth Headset
31
Downloaded from www.Manualslib.com manuals search engine
ENTERTAINMENT
32
To connect network
-- One-click network connection
-- To connect to a network through Set
Expert
-- To Use the Wi-Fi Direct Function
-- To Use the Miracast™/Intel’s WiDi
Function
-- Tips for Network Settings
32
32
SMARTSHARE
35
Before Using
-- Connecting a USB Device
-- Removing a USB Device
35
35
35
To Use SmartShare™
-- Watching the Videos
-- Viewing the Photos
-- Listening to Music
-- Viewing Files
-- To Set SmartShare™ Related Functions
37
38
40
41
42
43
32
33
33
34
To Connect DLNA
47
-- To connect a DLNA-authenticated
Smartphone
47
-- To connect DLNA DMR (Digital Media
Renderer)
47
-- To connect DLNA DMP (Digital Media
Player)
48
-- SmartShare™ PC SW Installing & Setting
49
-- In Case of a DLNA Malfunction
50
CUSTOMIZING SETTINGS
51
SETTINGS
51
PICTURE Settings
52
CONTENTS
SOUND Settings
57
TIME Settings
60
OPTION Settings
61
NETWORK Settings
63
SUPPORT
64
CONNECTING DEVICES
65
Connecting to HD Receiver, DVD, VCR, or
External Devices
66
-- HDMI Connection
66
-- HDMI to DVI Connection
67
-- AV Connection
67
-- Component Connection
68
Connecting to Headphones
68
Connecting a Digital Amp
69
Connecting to PC and Laptop
-- HDMI Connection
70
70
Using the Mirroring Function of a Mobile
Phone
71
-- MHL Connection
71
MAINTENANCE
72
Cleaning
-- Cleaning the Lens
-- Cleaning the Projector Case
72
72
72
INFORMATION
73
To Update Projector Software
73
SPECIFICATIONS
74
Downloaded from www.Manualslib.com manuals search engine
13
14
PREPARATION
PREPARATION
Accessories
Accessories included with the project are show below. The pictures may differ slightly
from the actual product. Accessories are subject to change without prior notice. New
accessories may be added or old ones removed.
70-
1"(&
Remote Control
Two AAA Batteries
Owner's Manual
Power Cord
Composite Gender
Component Gender
Owner's Manual CD
yyWhen connecting an HDMI or USB cable, or
connecting a USB flash drive to the HDMI or USB
port, use a product that has a width of 18 mm or
less and a height of 10 mm or less. If the USB cable
or USB flash drive does not fit the USB ports of the
projector, use an extension cable that supports USB
2.0.
Downloaded from www.Manualslib.com manuals search engine
PREPARATION
Optional Extras
To purchase optional accessories, visit an electronics store or online shopping site or
contact the retail store where you purchased the product. Optional accessories are
subject to change without prior notice.
Projection Screen
Tripod
HDMI Cable
Video Cable
Audio Cable
MHL Cable
Optical Cable
LG Audio Device
Downloaded from www.Manualslib.com manuals search engine
15
16
PREPARATION
Parts and Components
The projector is manufactured using high-precision technology. You may, however, see
tiny black dots and/or bright colored dots (red, blue or green) that continuously appear
on the projector screen. This is a normal result of the manufacturing process and does
not indicate a malfunction.
Front
Control Panel
1
Vent
Speaker
Speaker
Lens2
Button
(POWER)
(MENU)
, (Volume)
, , ,
(OK)
Description
Turns the projector on or off.
Displays or closes the Settings menu.
Adjusts the volume level.
Moves between menus and changes the settings.
Shows the current mode and saves changes to the settings.
1 Due to the high temperature of vent area, do not get close to the vent area.
2 Do not touch the lens while using the projector. The lens may be damaged.
Downloaded from www.Manualslib.com manuals search engine
PREPARATION
Back
(Headphone Port)
USB IN 1 Port
OPTICAL DIGITAL AUDIO OUT Port
USB IN 2 Port
LAN Port
HDMI IN 1 (ARC) Port
COMPONENT IN Port
HDMI IN 2 (MHL) Port
AV IN Port
AC IN Port
Downloaded from www.Manualslib.com manuals search engine
17
18
PREPARATION
Installation
Installation Precautions
yyPlace the projector in a well-ventilated
environment.
- To prevent internal heat build-up,
install the projector in a wellventilated place.
Do not place anything near the
projector as this may block its air
vents. If the air vents are blocked,
the internal temperature will
increase.
- Do not place the projector on a
carpet or rug. If the vent is on the
bottom, use the projector on a solid
level surface and ensure the vent is
not blocked.
- Be sure to prevent foreign objects
such as paper debris from entering
the projector.
- Leave enough distance (30 cm or
more) around the projector.
Downloaded from www.Manualslib.com manuals search engine
yyDo not place the projector in a hot
or humid environment.
- Do not place the projector in a hot,
cold, or humid environment.
yyDo not place the projector in a place
where it will easily attract dust.
- This may result in fire.
yyNever open any cover on the
projector. There is a high risk of
electric shock.
yyThe projector is manufactured using
high-precision technology. You may,
however, see tiny black dots and/
or bright colored dots (red, blue or
green) that continuously appear on
the projector screen. This is a normal
result of the manufacturing process
and does not indicate a malfunction.
yyThe remote control may not work
in an environment where a lamp
equipped with electronic ballasts or
a three-wavelength fluorescent lamp
is installed. Replace the lamp with an
international standard lamp for the
remote control to work normally.
yyTo adjust the angle of the projector,
turn the adjustment legs to the left or
right while pressing on the rubber part
at the same time.
PREPARATION
19
Projection Distance per Screen Size
1 Place the projector on a sturdy, level surface, together with the PC or audio/video
source.
2 Place the projector an appropriate distance away from the screen. The distance
between the projector and the screen determines the actual size of the image.
3 Position the projector so that the lens is at a right angle to the screen. If the
projector is not at a right angle, the projected image will look distorted. To correct the
distortion, use the Keystone function. (See page 25.)
4 Connect the power cord of the projector and the connected device to the wall outlet.
Ratio of upward projection: 100 %
Screen Width (Y)
Screen Height (X)
Screen
X/2
X/2
Projection distance (D)
Y/2
Screen
47.7 mm
Y/2
Projection distance (D)
16:9 Ratio
Screen Size (mm)
Screen Width (Y) (mm)
508
635
762
889
1016
1143
1270
1397
1524
1651
1778
1905
2032
2159
2286
2413
2540
2667
2794
2921
3048
443
553
664
775
886
996
1107
1218
1328
1439
1550
1660
1771
1882
1992
2103
2214
2324
2435
2546
2657
Downloaded from www.Manualslib.com manuals search engine
Screen Height (X)
(mm)
249
311
374
436
498
560
623
685
747
809
872
934
996
1058
1121
1183
1245
1308
1370
1432
1494
Projection Distance
(D) (mm)
621
776
932
1087
1242
1397
1553
1708
1863
2018
2174
2329
2484
2639
2795
2950
3105
3260
3416
3571
3726
20
PREPARATION
How to Install the Projector On a Tripod
yyYou can install this projector using a camera tripod.
As shown below, you can mount the projector instead of a camera on the tripod.
yyWhen stabilizing the tripod, we recommend using a locking bolt of standard size
4.5 mm or less. The maximum size allowed for the locking bolt is 5.5 mm.
(If it is longer than the maximum allowed size, it may damage the projector.)
Bolt used to
attach the
projector
Bottom side of the projector
⇒
+
The projector is
connected to this part.
Tripod
CAUTION
yyIf you are using a tripod, be careful not to apply external force to the tripod. Doing
so may damage the projector.
yyDo not place the tripod on an unstable surface.
yyBe sure to use a tripod with a maximum load capacity of 3 kg or more.
yyTo use the projector safely, position the tripod legs so that they are as wide and
stable as possible and be sure to securely attach the projector to the tripod.
Kensington Security System
yyThis projector has a Kensington Security Standard connector. Connect a Kensington
Security System cable as shown below.
yyFor more information on installation and use of the Kensington Security System,
refer to the user’s guide provided with the Kensington Security System.
yyThe Kensington Security System is an optional accessory.
yyWhat is Kensington? Kensington is a company that provides security systems for
laptops and other electronic devices. Website: http://www.kensington.com
Downloaded from www.Manualslib.com manuals search engine
REMOTE CONTROL
REMOTE CONTROL
Open the lid at the back of the remote control and insert
the batteries as described in the
instructions.
Use new batteries and do not mix regular or rechargeable
batteries. (1.5 V AAA)
CAUTION
yyDo not mix new batteries with old ones.
POWER
Turns the projector on or off.
ENERGY SAVING
Adjusts the screen brightness.
INPUT
Changes the input source.
70-
1"(&
Downloaded from www.Manualslib.com manuals search engine
Number Buttons
Enters a number.
SLEEP
Sets the sleep timer.
STILL
Stops the video being played.
VOL +, Adjusts the volume level.
BLANK
Blanks the screen.
RATIO
Changes the aspect ratio of the screen
per pressing of the button.
MUTE
Mutes the sound of the projector.
PAGE ,
Moves to the previous/next page.
21
22
REMOTE CONTROL
70-
1"(&
SETTINGS
Displays or closes the Settings menu.
PICTURE
Changes the picture mode per press of the
button.
Q.MENU
Allows you to change the settings easily.
Up/Down/Left/Right buttons
Switches between menu functions.
OK
Shows the current mode and saves changes to
the settings.
Returns to the previous screen.
AV MODE
Selects AV mode for the genre of the program
being watched.
EXIT
Exits the menu.
Playback control buttons
Controls the playback of multimedia content on
the SmartShare.
Allows you to use the SIMPLINK function.
Key's ▲, ▼
Adjusts the Keystone function.
GRID
Shows 20 grids built into projector to align and
compose images and designs.
Color buttons
Sets detailed settings or gesture for each menu.
NOTE
yyWhen using the remote control, the optimal operation range is
6 meters or less (left/right) and within a 30 degree arc of the
remote control IR receiver.
yyIf a cable is connected to the back port, the optimal operating
range is 3 meters or less (left/right) and within a 30 degree arc of
the remote control IR receiver.
yyFor seamless operation, do not block the IR receiver.
yyWhen you carry the remote control in the portable bag, make
sure that the buttons on the remote control are not pressed by the
projector, cables, documents or any other accessories in the bag.
Otherwise, it may significantly reduce the battery life.
Downloaded from www.Manualslib.com manuals search engine
30 ° 30 °
70-
1"(&
USING THE PROJECTOR
23
USING THE PROJECTOR
Watching Projector
Initial Setup
The menu screen display in this owner's manual is an example to help users
understand how to operate the product and may look different from the actual screen.
1 Connect the power cord correctly.
2 After waiting for a moment, press the POWER button on the remote control or the
control panel.
3 When you turn on the projector for the first time, a setting screen appears as shown
below. Here, you can specify the items required for watching the projector more
easily.
Downloaded from www.Manualslib.com manuals search engine
24
USING THE PROJECTOR
* The initial settings are completed when you select the settings above.
Focus of the Screen Image
When an image appears on the screen, check if it is in focus and fits the screen
properly.
To adjust the focus of the image, rotate the focus ring.
Focus Ring
Downloaded from www.Manualslib.com manuals search engine
USING THE PROJECTOR
25
Additional Options
Using the Keystone
Function
Adjusting Aspect Ratio
To prevent the screen image from
becoming trapezoidal, Keystone adjusts
the top and bottom width of the image
if the projector is not set up at a right
angle to the screen.
Because the Keystone function may
cause inferior screen image quality, use
this function only when it is not possible
to set up the projector at an optimal
angle.
yyPress the SETTINGS button on the
remote control. Select PICTURE →
Aspect Ratio to change the aspect
ratio.
yyYou can also use the Q.MENU or
RATIO button.
Menu
16:9
Just
Scan
Description
Resizes images to fit the
screen width.
Displays video images in
the original size without
removing parts of the edge
of the image.
yyIn HDMI/Component (over
720p) mode, Just Scan
is available.
Set By
Depending on the input
Program signal, screen aspect ratio
changes to 4:3 or 16:9.
4:3
Resizes the image ratio to
fit 4:3 screen.
Zoom
Resizes the image to fit the
screen width. The top and
bottom parts of the image
may be cut off.
Cinema Formats an image to the
Zoom 1 cinemascope ratio (2.35:1)
and zooms in on the ratio.
NOTE
yyAvailable picture size may differ
depending on the input signal.
yyThe screen aspect ratios on HDMIPC input are available in 4:3 and
16:9 only.
Downloaded from www.Manualslib.com manuals search engine
1 Press the Key's
or Key's
button to adjust the picture.
yyKeystone can be adjusted
from -40 to 40.
2 Press the OK button when done.
26
USING THE PROJECTOR
Changing Input Device
To use SIMPLINK
To select an external input
Selects external input.
yyPress the INPUT button on the
remote control to display the input
selection screen.
- Connected inputs are displayed first.
However, AV is always activated.
yySelect an input signal using the
remote control's INPUT button to
connect the projector to the desired
input. You can use the or button
to switch between all the input modes.
INPUT LIST
SIMPLINK is a feature that enables
you to control and manage various
multimedia devices conveniently using
the projector remote control only via the
SIMPLINK menu.
1 Connect the projector's HDMI IN
terminal with SIMPLINK device's
HDMI output terminal using HDMI
cable. For home theater units with
SIMPLINK function, connect HDMI
terminals as above and use an
optical cable to connect Optical
Digital Audio Out from the projector
to Optical Digital Audio In of the
SIMPLINK device.
Select an input device to view.
2 Press the SIMPLINK button on the
AV
No Signal
remote control.
The SIMPLINK menu window
appears.
Projector Speaker
AV
Component
HDMI1
3 Select SIMPLINK Setting on
HDMI2
Change Device Name
SIMPLINK Setting
Selecting an Input Label
Displays which devices are connected to
which input ports.
1 Press the INPUT button on the
remote control to display the input
selection screen.
2 Press the red button.
3 Press the or button to go to
the desired input and press the OK
button.
4 User the
, , , or
select a device name.
Downloaded from www.Manualslib.com manuals search engine
button to
SIMPLINK menu window. SIMPLINK
Setting window appears.
4 SIMPLINK Setting to On in
SIMPLINK setup window.
5 Close SIMPLINK Setting window.
6 Press the SIMPLINK button on the
remote control.
Select the device you want to control
in the SIMPLINK menu window.
USING THE PROJECTOR
NOTE
yyThis function only works on devices
).
with the SIMPLINK logo (
Verify that the external device has
a SIMPLINK logo.
yyTo use the SIMPLINK function, you
need to use a high-speed HDMI®
cable (with CEC, or Consumer
Electronics Control, feature added).
High-speed HDMI® cables have
the No. 13 pin connected for
information exchange between
devices.
yyTurn on or select the media of a
device with home theatre features
to see the speaker switch to
External Speaker.
yyConnect with an optical cable (sold
separately) to use external speaker.
yySwitching to external input causes
devices operating with SIMPLINK
to stop.
yyUse of a third-party device with
HDMI-CEC features may cause
malfunctions.
Downloaded from www.Manualslib.com manuals search engine
27
Explanation on SIMPLINK features
Menu
Description
Direct Play Plays the multimedia
device on the projector
instantly.
Select
Selects the desired
multimedia device via the SIMPLINK
device
menu to control it from
the projector screen
instantly.
Disc
playback
Manages the multimedia
device with the projector
remote control.
Power off
all devices
If the Auto Power
function is set to On in
the SIMPLINK settings,
turning the projector off
will turn the power off on
all SIMPLINK-connected
devices.
Sync
Power on
If the Auto Power
function is set to On in
the SIMPLINK settings,
turning on a SIMPLINK
device will turn the
projector on.
Speaker
Selects speaker either
on the home theatre unit
or the projector.
28
USING THE PROJECTOR
Using the Quick Menu
You can customize frequently used menus.
1 Press the Q.MENU button.
2 Press the or button to select a
menu and press OK.
Menu
Aspect
Ratio
Picture
Mode
Sound
Mode
Sleep
Timer
Description
Resizes the picture.
Changes the picture mode.
Sets the sound mode.
Sets the projector to be
turned off at the specified
time.
Adjusts the brightness.
Energy
Saving
AV Mode Sets the mode.
Mode
Off
You can watch
using the
settings in the
video/audio
menu.
Cinema Change to
optimal video/
audio settings
for movies.
Game
Change to
optimal video/
audio settings
for games.
USB
Allows you to remove a
Device
connected USB device in a
safe manner.
3 Press the
, , , or button to
scroll through the following menus.
Downloaded from www.Manualslib.com manuals search engine
USING THE PROJECTOR
To Set Sound
To Set Sound Output
yyPress the SETTINGS button on the
remote control. Select SOUND →
Sound Out → External Speaker
(Optical/HDMI ARC) → ARC Mode.
Menu
To use projector’s speakers
Even when the connected
ARC-supported external
audio device is turned
on, audio output is not
automatically processed
through the external audio
device's speakers.
On
If ARC-supported external
audio device is turned on,
audio output is automatically
processed through the
external audio device
speakers.
yyPress the SETTINGS button on the
remote control. Select SOUND →
Sound Out → Projector Speaker.
Sound is output through the speaker
connected to the optical port.
SIMPLINK is supported.
yyPress the SETTINGS button on the
remote control. Select SOUND →
Sound Out → External Speaker
(Optical/HDMI ARC) to set up as
follows:
Menu
Description
ARC
Mode
External audio devices
can be connected via
High-Speed HDMI® cable
without an extra optical
audio cable to output
SPDIF. It interfaces with
SIMPLINK.
For an external device
that supports ARC (Audio
Return Channel), connect
it to the HDMI IN 1(ARC)
port.
Digital
Sound
Out
Sets up Digital Sound
Output.
Downloaded from www.Manualslib.com manuals search engine
Description
Off
Sound is output through the projector
speaker.
To Use External Speaker
29
NOTE
yyConnect to ARC-only terminal when
connecting to external devices.
yyUse high-speed HDMI® cable when
connecting to external devices.
yyUse of a third-party device with
an ARC function may cause
malfunctions.
30
USING THE PROJECTOR
yyPress the SETTINGS button on the
remote control. Select SOUND →
Sound Out → External Speaker
(Optical/HDMI ARC) → Digital
Sound Out.
Item
Sound Input
Auto MPEG
Digital Sound
Out
PCM
Dolby Digital
Dolby Digital
Dolby Digital
Plus
Dolby Digital
HE-AAC
Dolby Digital
PCM All
PCM
To connect and use LG audio device
LG audio device allows you to enjoy rich
powerful sound easily.
yyWired Connection:
Press the SETTINGS button on the
remote control. Select SOUND →
Sound Out → LG Sound Sync
(Optical).
Connect LG audio device with the
logo to the OPTICAL DIGITAL
AUDIO OUT port.
yyWireless Connection:
Press the SETTINGS button on the
remote control. SOUND → Sound
Out → LG Sound Sync (Wireless).
LG audio device with the
can be connected wirelessly.
Downloaded from www.Manualslib.com manuals search engine
logo
USING THE PROJECTOR
NOTE
yyYou can use the projector remote
control to adjust the volume of the
connected device.
yyFor a wireless connection, if the
device fails to connect, check the
device power and make sure the LG
Audio device is set up properly.
yyWhen you select LG Sound Sync
(Wireless), devices available for
connection are searched and one of
searched devices is automatically
connected. When a device is
connected, its name is shown.
yyIf two or more devices are detected,
the first detected device is connected
first. To view more detected devices
to connect, press the Show More
button.
yyWhen LG Sound Sync (Wireless) is
active and you turn on the projector,
it will search and try to connect the
device which recently connected.
Downloaded from www.Manualslib.com manuals search engine
31
To Connect and Use a
Bluetooth Headset
Sound output is through the Bluetooth
headset.
yySMART → Settings → SOUND
ⱞⳮ
HOME
→ Sound Out → LG Sound Sync
(Wireless)
yyThe devices that can be connected
are: LG BTS1, LG HBS-700, LG
HBS-730, LG HBS-800 (Product
availability may vary by country.)
yⰶᲳ
yFor wireless
ㄮᗺ connection, if the device
fails to connect. Check the device power
to connect and if the LG Audio device is
in? a proper operating condition.
Ẳⱞ⩛
/ხ㢢☎⳿ devices are detected,
If two or more
the first detected device is connected
first. To view more detected devices to
connect, press the Show More button.
32
ENTERTAINMENT
ENTERTAINMENT
To connect to a network
through Set Expert
To connect network
For use in special circumstances such
as in offices (in cases where a static IP
is used).
A wireless or wired network connection
is required to use the DLNA function.
One-click network
connection
Connects easily to a wired/wireless
network.
yyPress the SETTINGS button on
the remote control. NETWORK →
Network connection to connect to
an available network automatically.
Follow the prompts on the projector.
yyPress the SETTINGS button on the
remote control. Select NETWORK →
Network connection.
1 Select a network connection, either
Wired or Wireless.
2 When connecting via Wi-Fi, use
the one of the following network
connection methods.
Item
AP List
Description
Connects to the network
selected from the AP List.
Enter the Connects to the wireless
SSID
AP typed in.
WPSPBC
Connects easily when the
button of a wireless AP
supporting PBC is pressed.
WPS-PIN Connects easily when the
PIN of the wireless AP
that you wish to connect
to is entered in to the AP
website.
Downloaded from www.Manualslib.com manuals search engine
ENTERTAINMENT
33
To Use the Wi-Fi Direct
Function
2 Enable the Miracast™/Intel’s WiDi
Wi-Fi Direct is a function that allows your
projector to connect with a Wi-Fi Direct
device without Internet connection. With
SmartShare™, you can watch the files
stored on a device connected via Wi-Fi
Direct.
3 A list of devices that can be
yyPress the SETTINGS button on the
remote control. Select NETWORK →
Wi-Fi Direct.
1 Set Wi-Fi Direct to On. (If you do not
use it, please change it to Off.)
2 Enable the Wi-Fi Direct settings on the
device that you want to connect to.
3 A list of devices that can be
connected to the projector is
displayed.
4 Select a device to connect.
5 Select Yes, when the connection
request message appears.
6 If the device that you want to connect
accepts the request, Wi-Fi Direct is
connected.
To Use the Miracast™/
Intel’s WiDi Function
You can view the screen of a device with
Miracast™ and Intel’s WiDi technologies
on your projector. Contact the device
manufacturer to find out if the device
supports this function.
yyPress the SETTINGS button on the
remote control. Select NETWORK →
Miracast™/Intel’s WiDi.
1 Set Miracast™/Intel’s WiDi to On.
(If you do not use it, please change it
to Off.)
Downloaded from www.Manualslib.com manuals search engine
settings on the device that you want
to connect to.
connected to the projector is
displayed.
4 Select a device to connect.
5 Select Yes, when the connection
request message appears.
6 If the device that you want to connect
accepts the request, Miracast™/
Intel’s WiDi is connected.
yyWhen Wi-Fi Direct is set to Off, if
you set Miracast™/Intel’s WiDi to
On, Wi-Fi Direct is automatically set
to On.
yyWhen you set the Miracast™/Intel’s
WiDi function to Off, Wi-Fi Direct
returns to the previous setting.
NOTE
yyIt is recommended to connect a
laptop using Intel’s WiDi within
close range.
yyThough Intel’s WiDi can be
connected without a wireless router,
it is recommended to connect the
wireless router first for optimal
performance.
yyYou may not connect your projector
to a non-Artograph device even
when it is detected.
yyIt is recommended you to connect a
device to a 5 GHz router.
yyThe response rate may vary
depending on the user’s environment.
yyFor more information on the device
you want to connect to, refer to its
owner’s manual.
34
ENTERTAINMENT
Tips for Network Settings
yyUse a standard LAN cable (Cat5
or higher with RJ45 connector, 10
Base-T or 100 Base TX LAN port).
yyResetting your modem can cause
network connection problems. To
resolve the problem, turn the power
off, disconnect and reconnect, and
then turn the power back on.
yyArtograph is not responsible for any
network connection problems or
any faults, malfunctions and errors
caused by an network connection.
yyA network connection may not work
properly depending on the Internet
service provider.
yyA DSL modem is required for a DSL
service; a cable modem is required
for a cable service. Only a limited
number of network connections
may be available, and projector
network setting may not be available
depending on your contract with your
Internet Service Provider (ISP). (If
only one device is allowed per line
and the PC is already connected,
other devices cannot be used.)
yyWireless networks can be subject
to interference from other devices
operating at a frequency of 2.4 GHz
(wireless phones, Bluetooth devices
or microwave ovens). There may also
be interference from devices with a
frequency of 5 GHz, same as other
Wi-Fi devices.
Downloaded from www.Manualslib.com manuals search engine
yyThe surrounding wireless environment
can cause the wireless network
service to run slowly.
yyIf you do not turn off the entire local
home network, network traffic may
occur on some devices.
yyFor an AP connection, an access
point device that supports wireless
connection is required and the
wireless connection feature must be
enabled on the device. Contact your
service provider regarding availability
of wireless connection on your access
point.
yyCheck the SSID and security settings
of the AP for AP connection. Refer
to the appropriate documentation for
SSID and security settings of the AP.
yyInvalid settings on network devices
(wired/wireless line sharer, hub) can
cause the projector to run slowly
or not operate properly. Install the
devices correctly according to the
appropriate manual and set the
network.
yyConnection method may differ
according to the AP manufacturer.
SMARTSHARE
SMARTSHARE
Before Using
Connecting a USB Device
Connect a USB device (external HDD,
USB memory) to the USB port of
projector to enjoy the content files stored
in the USB device with your projector.
You cannot write or delete data in the
USB device. Connect a USB flash drive
as shown below.
USB Flash Drive
Downloaded from www.Manualslib.com manuals search engine
35
Removing a USB Device
1 Click the Q.MENU button.
2 Use the or button to move
to USB Device and press the OK
button.
3 Select a USB to remove. Wait for
confirmation that the USB device has
stopped before removing the USB.
NOTE
yyIf detached early, an error may
occur on the projector or the USB
storage device.
yyOnce a USB device has been
selected for removal, it can no longer
be read. Remove the USB storage
device and then re-connect it.
36
SMARTSHARE
Tips for Using a USB Device
yyIf the USB storage device has a builtin auto recognition program or uses
its own driver, it may not work.
yySome USB storage devices may not
work or may work incorrectly.
yyIf you use a USB extension cable, the
USB device may not be recognized or
may not work properly.
yyUse only USB storage devices
formatted with the Windows FAT32 or
NTFS file system.
yyFor external USB HDDs, it is
recommended that you use devices
with a rated voltage of less than 5 V
and a rated current of less than 500
mA.
yyIt is recommended to use a USB
hub or hard disk drive with power
supplied. (If the power supplied is not
enough, the USB storage device may
not be detected properly.)
yyIt is recommended that you use USB
flash drives of 32 GB or less and USB
HDDs of 2 TB or less.
yyIf a USB HDD with power-saving
function does not work properly,
turn the power off and on. For more
information, refer to the user manual
of the USB HDD.
yyData in USB storage device can
be damaged so be sure to back
up important files to other devices.
Data maintenance is the user's
responsibility and the manufacturer is
not responsible for data loss.
Downloaded from www.Manualslib.com manuals search engine
SMARTSHARE
37
To Use SmartShare™
1 Press the SETTINGS button on the remote control.
2 Select SMART SHARE.
You can watch the photo, music, video and document on the projector by connecting
a USB or home network (DLNA). The photo, music, video and document files of all
devices connected to the projector are displayed. (For the document files, only those in
the devices connected via USB are displayed.)
SmartShare™
Recently Played
Recent
Videos
Photos
000
001
002
003
004
005
006
007
008
009
011
012
013
014
Music
File Viewer
Newly Added
Linked Device
010
Settings
Delete History
Connecting guide
Description
Displays photo / music / video / document files on all devices connected to the
projector.
Shows how to connect PC, smartphone/device, and USB.
Downloaded from www.Manualslib.com manuals search engine
38
SMARTSHARE
Watching the Videos
In the Movie List, you can watch movies stored on the connected USB device.
Controls playback and sets options while viewing videos.
Playing video - warning
yySome subtitles created by users may not work properly.
yyThe video and subtitle files should be placed in the same folder. For subtitles to
display correctly, the video and subtitle files must have the same name.
yySubtitles on an NAS (Network Attached Storage) device may not be supported
depending on the manufacturer and model.
yyWe do not support any stream that contains GMC (Global Motion Compensation) or
Qpel (Quarterpel Motion Estimation).
yyFuLL HD Video: 1920 X 1080
Only H.264 / AVC profile level 4.1 and lower is supported.
yyThe file size limit is dependent on the encoding environment.
yyIt works only the above version of Window Media Audio V2.
yyAAC Main Profile is not supported.
yyVideo files created by some encoders may not be played back.
yyVideo files in formats other than the ones specified here may not be played back.
yyPlayback of video files stored on the USB device that do not support High Speed,
may not work properly.
yyThe projector supports DTS audio codec when the USB/HDMI video file playback.
Downloaded from www.Manualslib.com manuals search engine
SMARTSHARE
39
To control video playback
You can control playback using the following buttons.
Option
Shows the current playing position. Use the
move forward or backward.
Item
or
button to
Description
Resumes normal playback.
Pauses the video player.
Displays in slow motion.
Whenever this button is pressed, the playback speed is increased or
decreased by one unit.
ꕙ
Plays the previous/next file.
ꕙ
Option Sets the option.
Downloaded from www.Manualslib.com manuals search engine
40
SMARTSHARE
Viewing the Photos
You can view photos stored on a connected device.
To control photo view
You can control playback using the following buttons.
Option
Item
,
Description
Selects the previous or next photo.
If no picture is selected, all photos in the current folder are displayed in a
slide show. If some photos are selected, those photos are displayed in a
slide show.
yySet Slide Show Speed in the Option → Set Photo View. menu.
You can listen to music while viewing full-size photos.
yySet BGM in the Option → Set Photo View. menu.
Rotates photos.
yyRotates a photo 90 °, 180 °, 270 °, 360 ° clockwise.
yyPhotos cannot be rotated if their width is greater than the height of the
maximum supported resolution.
Enlarges or reduces the photo.
Use the Up/Down/Left/Right buttons to select a page and press the OK
button.
Option A setting popup window will appear.
Downloaded from www.Manualslib.com manuals search engine
SMARTSHARE
Listening to Music
You can play audio files stored on the connected device.
To control music playback
You can control playback using the following buttons.
Changes the playing position.
Item
ꕙ
Description
Plays the previous/next file.
ꕙ
Pauses the music player.
Resumes normal playback.
Sets the repeat playback.
Sets the random playback.
Plays music with the projector screen turned off.
Sets Option for the music list.
yyYou can control playback using the , , and keys on a remote control.
yyIf you use the USB device, time information will be not shown on screen.
Downloaded from www.Manualslib.com manuals search engine
41
42
SMARTSHARE
Viewing Files
You can see document files stored on a connected device.
Supported File Formats
XLS, DOC, PPT, TXT, XLSX, PPTX, DOCX, PDF Microsoft Office 97/2000/2002/2003/2007 version
Adobe PDF 1.0/1.1/1.2/1.3/ 1.4 version
yyFile Viewer realigns a document, so it may look different from what is displayed on a
PC.
yyFor documents that include images, the resolution may look lower during the
realigning process.
yyIf the document is large or has many pages, it may take longer to load.
yyUnsupported fonts may be replaced by other fonts.
yyThe file viewer may not open for Office documents that contain many high resolution
images. In that case, reduce the image file size, save it on a USB storage device
and run the file viewer again or connect your PC to the projector and open the file on
your PC.
Browsing File Viewer
You can control playback using the following buttons.
yyPress the Go Page button to move to the previous or next page.
yyPress the volume button to zoom in or zoom out.
- Press the OK button.
- Press the Up/Down/Left/Right buttons to move to Go Page or Zoom.
[125%]
Go Page
11.pptx
Zoom
Item
Go Page
1 / 2 31 KB
Option
Description
Moves to the page you specify.
Zoom
Enlarges or reduces the document.
Option
Sets Option for File Viewer.
List
Returns to a list.
Downloaded from www.Manualslib.com manuals search engine
List
SMARTSHARE
43
To Set SmartShare™ Related Functions
Press the SETTINGS button on the remote control. Select SMART SHARE →
Settings.
Changes settings related to SmartShare™ content playback.
Advanced Setting
Item
Description
My Projector Name Changes the name that appears when searching for the
projector from other devices.
Network Status
Checks the network connection.
Wi-Fi Direct
Allows use of wireless connection functions such as Wi-Fi
Direct and WiDi.
Auto Play on
Receive
Accepts / rejects content transferred from other devices.
DivX(R) VOD
Registers or releases DivX.
Checks DivX Registration Code for playing DivX-protected
videos. Register at http://vod.divx.com.
Uses Registration Code to rent or purchase movies at
www.divx.com/vod.
yyWhen using the DivX Registration Code of another device,
the rented/purchased DivX file cannot be played. Use only
the DivX Registration Code granted to this device.
yyConverted files not conforming to DivX Codec Standard may
produce abnormal images and sound.
Delete History
yyTo delete contents history, press Delete History button.
yyUse the contents at Recent menu.
Downloaded from www.Manualslib.com manuals search engine
44
SMARTSHARE
SmartShare™ supporting file
yyMaximum data transfer rate: 20
Mbps(Mega bit per second)
yyExternal subtitle formats supported:
*.smi, *.srt, *.sub (MicroDVD,
SubViewer 1.0/2.0), *.ass, *.ssa, *.txt
(TMPlayer), *.psb (PowerDivX)
yyInternal subtitle formats supported:
XSUB (supports internal subtitles
generated from DivX6)
Subtitle Language
Subtitle
Language
Language
Latin1
English, Spanish,
French, German, Italian,
Swedish, Finnish, Dutch,
Portuguese, Danish,
Romanian, Norwegian,
Albanian, Gaelic, Welsh,
Irish, Catalan, Valencian
Latin2
Bosnian, Polish,
Croatian, Czech, Slovak,
Slovenian, Serbian,
Hungarian
Latin4
Estonian, Latvian,
Lithuanian
Cyrillic
Bulgarian, Macedonian,
Russian, Ukranian,
Kazakh
Greek
Greek
Turkish
Turkish
Hebrew
Modern Hebrew
Chinese
Simplified Chinese
Korean
Korean
Arabic
Arabic
Downloaded from www.Manualslib.com manuals search engine
SMARTSHARE
Video Supported Codec
Maximum resolution: 1920 x 1080 @ 30p
Extension
.asf
.wmv
Codec
Video
VC-1 Advanced Profile, VC-1 Simple and Main Profile
Audio
WMA Standard, WMA 9 Professional
Video
DivX3.11, DivX4, DivX5, DivX6, XViD, H.264/AVC,
Motion Jpeg, MPEG-4 Part 2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3),
Dolby Digital, Dolby Digital Plus, LPCM, ADPCM, DTS
Video
H.264/AVC, MPEG-4 Part 2
Audio
AAC , MPEG-1 Layer III (MP3)
Video
H.264/AVC, MPEG-4 Part 2
Audio
AAC, AMR-NB, AMR-WB
Video
H.264/AVC
Audio
HE-AAC, Dolby Digital
Video
H.264/AVC, MPEG-2, VC-1
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3)
Dolby Digital, Dolby Digital Plus, AAC
Video
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
Video
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III(MP3), AAC
.divx
.avi
.mp4
.m4v
.mov
.3gp
.3g2
.mkv
.ts
.trp
.tp
.mts
.m2ts
.vob
.mpg
.mpeg
Downloaded from www.Manualslib.com manuals search engine
45
46
SMARTSHARE
Audio File
File type
mp3
Item
Info
Bit rate
32 Kbps - 320 Kbps
Sample freq.
16 kHz - 48 kHz
Support
MPEG1, MPEG2, Layer2, Layer3
Available photo file
File type
2D
(jpeg, jpg,
jpe)
Item
JPEG
Downloaded from www.Manualslib.com manuals search engine
Profile
Minimum: 64 x 64
Maximum: Normal Type: 15360 (W) x 8640 (H)
Progressive Type: 1920 (W) x 1440 (H)
SMARTSHARE
To Connect DLNA
DLNA stands for Digital Living Network
Alliance, which allows you to enjoy
video / music / photo files stored on a
PC or server on your Projector via home
networking.
To connect a DLNAauthenticated
Smartphone
The Projector and the smartphone should
be on the same network.
1Ensure that Wi-Fi is enabled on the
smartphone.
2Install / run the app to share content
on the smartphone.
3 Run Share my mobile phone
Content.
4Select the kind of content (video /
music / photo) you wish to play.
5Select the video, music or photo file
to play on the Projector.
6 Select Add to Play List.
7Select Projector model name on the
device you want to play content from.
(Projector model name is on the label
of the device.)
8Play
Shows the selected file on
Projector.
Downloaded from www.Manualslib.com manuals search engine
47
To connect DLNA DMR
(Digital Media Renderer)
If the PC's operating system is Windows
7 or Windows 8 or the DLNA-certified
device (e.g. mobile phone) is connected
via a network, you can play music /
videos / photos on Projector without
installing a separate program.
1 Configure Projector and PC on the
same network. Configure Windows
7 or Windows 8-installed PC on the
network.
2 Right-click the music / video / photo
file that you want to play and use
the Remote Playback feature that
comes with Windows 7 or Windows
8.To play content from a device
such as a mobile phone, refer to the
Owner's Manual for the device.
3 Content will be played on one device
only even if more than one Projector or
device is connected. Play speed can
vary depending on network speed.
48
SMARTSHARE
To connect DLNA DMP
(Digital Media Player)
With a PC having SmartShare™ PC
software, music / video / photo files may
be replayed on the projector by linking
them via home networking.
1 Configure projector and PC on the
same network. The projector and
each device should be connected
through a single access point to
enable DLNA service.
2 Install SmartShare™ PC software
on the PC from the website. Before
installation, close all running
programs including firewall and antivirus programs.
3The sever should be running in order
to watch the shared file on your
Projector.
Downloaded from www.Manualslib.com manuals search engine
SMARTSHARE
49
SmartShare™ PC SW Installing & Setting
Install the SmartShare™ PC SW(DLNA) programme on your PC.
1 Download the setup file from the path below in order to use the DLNA function.
http://liu.lge.com/smartshare/release/smartshare.zip
2 Install the downloaded SmartShare™ PC software.
3You can run the programme when installation is complete.
NOTE
yyDLNA or Media Link service is only available if projector and other devices are
connected via a single router.
PC requirement for installing LG SmartShare™
Item
Recommended
Specifications
Minimum Specifications
CPU
Intel Pentium Dual Core or
Intel Pentium 4 2.0 G or higher/
higher/AMD Athlon 64 x 2 or
AMD Sempron 2000 or higher
higher
RAM
1 GB or higher
2 GB or higher
VGA
64 MB RAM, 1024 x 768 or
higher resolution, and a video
card that supports 16 bit or
more colors
128 MB RAM, 1024 x 768 or
higher resolution, and a video
card that supports 16 bit or
more colors
Hard Disk Drive
Operating
System
Network
Environment
200 MB or higher
Windows XP (Service Pack 2 or later), Windows Vista, Windows
7, Windows 8
l Windows Media Player: 11.0.5721.5280 or higher is
recommended
100 MB Ethernet, Wireless LAN (WLAN) IEEE 802.11g or higher
yyProgram speed can be delayed depending on the system performance and the
network environment.
Downloaded from www.Manualslib.com manuals search engine
50
SMARTSHARE
In Case of a DLNA
Malfunction
yyIf the DLNA feature does not work
properly, check your network settings.
yyA 5-GHz access point is needed to
view 1080p videos via DLNA. A 2.4GHz access point may cause frequent
buffering or other problems.
yyDLNA may not work properly in the
wireless network. It is recommended
to connect to the wired network.
yyWhen playing video in DLNA mode,
Multi Audio and internal subtitles are
not supported.
yyIf more than one projector is
connected to a single server in DLNA
mode, the content may not play
depending on server performance.
yySubtitles may not be supported
depending on the DLNA device.
yyDLNA feature may not work
properly depending on the network
environment.
yyDLNA feature cannot be used with
some access points that do not
support multicasting. For more
information, refer to the access point
manual or consult the manufacturer.
yySupported file types may differ
depending on DLNA server
environment, even for file types
supported by the projector.
yyToo many sub-folders and files in one
folder may cause malfunction.
yyThe information about the file from the
DLNA server may not be displayed
correctly.
yyWhen viewing video subtitles on a
DLNA server, we recommend that
you use SmartShare™ PC Software.
Downloaded from www.Manualslib.com manuals search engine
yyIf subtitle file is added later, turn off
the shared folder and reset.
yyDRM file located on a SmartShare PC
Software server cannot be played.
CUSTOMIZING SETTINGS
CUSTOMIZING SETTINGS
SETTINGS
1 Press the SETTINGS button.
2 Use the , , , or button to select the desired item and press the OK button.
3 Use the , , , or button to set up the desired item and press the OK button.
4 Press the EXIT button when completed.
Menu
Description
PICTURE
Adjusts the image quality for optimal viewing.
SOUND
Adjusts the sound quality and volume level.
TIME
Sets time-related settings.
OPTION
Customizes the general settings.
NETWORK
Sets the network.
SUPPORT
Shows the projector information.
Downloaded from www.Manualslib.com manuals search engine
51
52
CUSTOMIZING SETTINGS
PICTURE Settings
PICTURE
1 Press the SETTINGS button.
2 Use the , , , or button to select
PICTURE and press the OK button.
yy ꕊ Energy Saving
: Minimum
yy Picture Mode
: Standard
yy Contrast 100
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
yy Brightness 50
yy Sharpness 20
yy Color
60
yy Tint
0
R
G
Ͱ
The available picture settings are described as follows.
Item
Energy
Saving
Description
Reduces power consumption by adjusting screen brightness.
Mode
Minimum/
Medium/
Maximum
Picture
Mode
Applies the pre-set Energy Saving mode.
- If Energy Saving is set to Minimum and the ambient
temperature is 35 °C or higher, Energy Saving will be
disabled.
Selects the picture mode optimized for the viewing environment or the
programme.
You can also customize advanced options for each mode.
Mode
Vivid
Standard
Cinema
Game
Expert1/2
Contrast
Maximizes the visual effect of video.
Heightens contrast, brightness and sharpness to display
vivid images.
Displays images in standard levels of contrast,
brightness and sharpness.
Optimizes the image for a movie.
Optimizes the image for playing games on fast-moving
screens.
Menu for adjusting picture quality that allows experts
and amateurs to enjoy the best projector viewing.
- Expert mode is for picture tuning professionals to
control and fine-tune using a specific image. For
normal images, the effects may not be dramatic.
Adjusts the difference between bright and dark regions of the screen.
Brightness Adjusts the overall screen brightness.
Sharpness
Adjusts the sharpness of the borders between bright and dark.
Horizontal and vertical sharpness are available only in Expert1/2.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
Item
53
Description
Color
Adjusts the colours on the screen darker or lighter.
Tint
Adjusts the red/green colour balance.
Advanced
Control
(Expert
Control)
Customizes the advanced settings.
Picture
Option
Sets optional settings.
Picture
Reset
Resets values customized by the user.
Each picture mode is reset. Select the picture mode you wish to reset.
Aspect
Ratio
Resizes the picture.
Picture
Wizard II
Use the remote control and follow the instructions of the Picture Wizard
to calibrate and adjust for optimum picture quality without expensive
pattern devices or help from a specialist. Follow the instructions to
obtain the optimum picture quality.
Downloaded from www.Manualslib.com manuals search engine
54
CUSTOMIZING SETTINGS
Advanced Control
Item
Description
Dynamic
Contrast
Adjusts contrast and colour to the optimal level according to the
screen’s brightness.
Dynamic
Color
Adjusts colours for more natural-looking colours.
Preferred
Color
Skin Color
Grass
Color
Skin colour spectrum can be separately set to implement
the skin colour as defined by the user.
Natural colour spectrum (meadows, hills, etc.) can be
set separately.
Sky Color
Sky colour is set separately.
Super
Resolution
Provides a crystal-clear picture by improving the details in areas where
the picture is blurry or unclear.
Gamma
Sets the gradation curve according to the output of the picture signal in
relation to the input signal.
Expert Control
Item
Description
Dynamic
Contrast
Adjusts contrast and colour to the optimal level according to the
screen’s brightness.
Super
Resolution
Provides a crystal-clear picture by improving the details in areas
where the picture is blurry or unclear.
Color Gamut
Selects the range of colours that can be expressed.
yyStandard: Displays the original colors of an input signal
regardless of the display features.
yyWide: Makes use of the display's rich colors.
Edge Enhancer Shows clearer and distinctive yet natural edges of the video.
xvYCC
Displays much richer colors.
Color Filter
Filters a specific colour spectrum in RGB colours to fine-tune colour
saturation and hue accurately.
Gamma
Sets the gradation curve according to the output of the picture
signal in relation to the input signal.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
55
Item
Description
White Balance
Adjusts white balance. Detailed adjustment is possible as shown below.
a. Method: 2 points
- Pattern: Inner, Outer
- Points: Low, High
- Red/Green/Blue: Adjustable range -50 - +50.
- Apply to all inputs: The values of the White Balance is applied
to all the input modes.
b. Method: 20 point IRE
- Pattern: Inner, Outer
- Institute of Radio Engineers (IRE) is the unit indicating the size
of a video signal and can be set to 5, 10, 15, ... 100.You can
fine-tune for each setting as shown below.
- Red/Green/Blue: The adjustment range is -50 - +50.
- Apply to all inputs: The values of the White Balance is applied
to all the input modes.
Color
Management
System
Adjusts Red/Green/Blue/Cyan/Magenta/Yellow colors. Allows an
expert to adjust the tint using a test pattern. Six colors (Red/Green/
Blue/Cyan/Magenta/Yellow) can be selectively adjusted without
affecting other colors. You may not see colors change on a normal
picture even after adjustment.
- Saturation Red/Green/Blue/Yellow/Cyan/Magenta,
Tint Red/Green/Blue/Yellow/Cyan/Magenta,
Luminance Red/Green/Blue/Yellow/Cyan/Magenta:
The adjustment range is -30 - +30 each.
* Depending on input signal or other picture settings, the range of detailed items for
adjustment may differ.
Downloaded from www.Manualslib.com manuals search engine
56
CUSTOMIZING SETTINGS
Picture Option
Item
Description
Noise Reduction Reduces screen noise in the video.
MPEG Noise
Reduction
Eliminates noise generated while creating digital picture signals.
Black Level
Adjusts the brightness or darkness of the screen to suit the black level of
the picture input using the degree of darkness (black level) of the screen.
Real Cinema
Optimizes the screen for movie viewing.
TruMotion
Corrects images to display smoother motion sequences.
Mode
Smooth De-Judder value is set to 3.
Clear
De-Judder value is set to 7.
User
De-Judder can be set manually.
yyDe-Judder: This function adjusts juddering of the screen.
Color
Temperature
Adjusts the overall color of the screen to suit your preference.
You can select Medium, Warm, Natural or Cool.
Peak Mode
Adjusts the brightness to the optimal level for the image.
- If the image is mostly white, the brightness level increases. If the
image mainly consists of red/green/blue/blue green/magenta/
yellow colors, you may not see a change in brightness.
-P
eak Mode is only enabled when Picture Mode is set to Vivid
and Energy Saving is set to Minimum.
- If Peak Mode is enabled, Energy Saving and Color
Temperature are disabled.
* If the video signal is 60 Hz, TruMotion may not work.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
57
SOUND Settings
SOUND
1 Press the SETTINGS button.
2 Use the , , , or button to select SOUND
yySmart Sound Mode : Off
and press the OK button.
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
yySound Mode
: Standard
yyVirtual Surround Plus
: Off
yyClear Voice II
: Off
yyVolume Mode
yySound Out
yyAV Sync. Adjust
: Projector Speaker
: Off
Ͱ
The available sound settings are described as follows.
Item
Smart Sound
Mode
Description
Provides the optimized sound adjusted for each content type.
yyIf the Smart Sound Mode function is enabled, Sound Mode, Virtual
Surround Plus and Clear Voice ll are automatically adjusted.
Sound Mode
Sets the sound mode.
Mode
Standard
Suitable for all types of video.
Music/ Cinema/ Sets audio optimized for a specific genre.
Sport/ Game
User Setting
Adjusts volume level.
yy100 Hz/ 300 Hz/ 1 kHz/ 3 kHz/ 10 kHz:
Sets EQ by manual adjustment of sound bands.
yyReset: Resets the equalizer value changed by
the user.
Virtual
Provides realistic 5.1 channel stereo sound from two speakers.
Surround Plus yyIf Clear Voice ll is set to On, Virtual Surround plus will not be
chosen.
Clear Voice II Boosts voice clarity.
Volume Mode Sets various modes for volume control.
Mode
Auto Volume
Automatically adjusts the volume level.
Volume Control Using a single volume curve may result in
an inaudible or loud sound depending on the
environment. Adjusts volume levels depending on
the time of day (day/night).
Downloaded from www.Manualslib.com manuals search engine
58
CUSTOMIZING SETTINGS
Item
Sound Out
Description
Sets the audio output of the projector.
Mode
Projector
Sound is output through the projector speaker.
Speaker
External
Sound is output through the speaker connected to
Speaker
the optical port. SIMPLINK is supported.
(Optical/HDMI
yyARC Mode: External audio devices can be
ARC)
connected via High-Speed HDMI® cable
without an extra optical audio cable to output
SPDIF. It interfaces with SIMPLINK.
For an external device that supports ARC (Audio
Return Channel), connect it to the HDMI IN
1(ARC) port.
yyDigital Sound Out: Sets up Digital Sound
Output.
LG Sound
Sound is output through an LG audio device
Sync (Optical) connected to the OPTICAL DIGITAL AUDIO OUT
port.
LG Sound Sync Sound is output through a wirelessly connected
(Wireless)
LG audio device.
Headphone
Sound is output through headphones.
yyHeadphones are detected and connected
automatically when the projector is on.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
Item
AV Sync.
Adjust
59
Description
Synchronizes video and audio directly when they do not match.
If you set AV Sync. Adjust to On, you can adjust the sound output
(Projector speakers or SPDIF) to the screen image.
Mode
Projector
Speaker
Adjusts the synchronization of the sound from the
projector's internal speakers.
The - button makes the sound output faster and
the + button slower than the default value.
External
Adjusts how the sound is synced to external
Speaker
speakers, such as an external speaker connected
to the digital audio output port, LG audio device,
and headphone.
The + and - buttons allow the viewer to
synchronize the audio with the video.
Bypass
Sends the natural sound of external devices
without any audio delay. Audio may be output
before video as it takes time to process video
input into the projector.
Sound Option Balance: Adjusts left/right audio balance.
Setting
Downloaded from www.Manualslib.com manuals search engine
60
CUSTOMIZING SETTINGS
TIME Settings
TIME
1 Press the SETTINGS button.
2 Use the , , , or button to select TIME and
press the OK button.
yySleep Timer
: Off
yyAuto Off
: 60 min.
yyAutomatic Standby : 4 hours
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
Ͱ
The available time settings are described as follows.
Item
Description
Sleep Timer Turns off the projector after a preset number of minutes.
To cancel the Sleep Timer, select Off.
Auto Off
If there is no signal, the projector automatically turns off after the preset
time has elapsed.
Automatic If you do not press any button on the projector or remote control for a
Standby
certain period, the projector will automatically switch to standby mode.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
61
OPTION Settings
OPTION
1 Press the SETTINGS button.
2 Use the , , , or button to select
yyLanguage
OPTION and press the OK button.
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
yyStandby Light
: On
yyPJT Mode
: Front
yyAuto Keystone
: On
yyKeystone
0
yyBlank Image : Blue
yyAuto Power
: On
-
+
Ͱ
The available option settings are described as follows.
Item
Description
Language
Selects a screen menu language.
Standby Light
Adjusts the LED button indicator.
Item
On
Off
When the buttons are touched, their indicators are
all turned on at maximum brightness. In standby
mode, LED indicators are turned on at 20 % of the
maximum brightness.
When the buttons are touched, their indicators are
all turned on at maximum brightness. In standby
mode, all LED indicators are turned off.
PJT Mode
This function turns the projected image upside down or flips horizontal.
Auto Keystone
Auto Keystone provides a rectangular screen image by
automatically adjusting the Keystone number when there is a
trapezoidal screen image caused by tilting of the projector.
Item
On
Automatically adjusts the Keystone number.
Off
Manually adjusts the Keystone number.
Keystone
To prevent the screen image from becoming trapezoidal,
Keystone adjusts the top and bottom width of the image if the
projector is not set at a right angle to the screen.
Blank Image
Selects a background for blank Image.
Downloaded from www.Manualslib.com manuals search engine
62
CUSTOMIZING SETTINGS
Item
Auto Power
Description
Makes the projector turn on automatically When the power code
is connected to the projector.
Item
On
Off
When the power code is connected to the
projector, it turns on automatically.
When the power code is connected to the
projector, it goes into standby mode.
High Altitude
If the projector is used at an altitude higher than 1200 meters,
turn this on.
Otherwise, the projector may overheat or its protection function
may be activated. If this happens, turn the projector off and then
on again after waiting for several minutes.
Auto Input
Search
Automatically searches for and displays the input signal type
when it is received. It is available only with external inputs (RGB,
HDMI, AV, and Component).
Balloon Help
Enables/disables the balloon help.
Grid Pattern
Shows 20 grids built into projector to align and compose images
and designs. The grids can be used alone as a template or
overlaid on any photo or image from any source.
Grayscale
Changes color to black and white.
Initial Setting
Deletes all optional settings and returns to initial default mode. Once
initialization is complete, the projector will turn off and on by itself.
yyDo not turn off the power during initialization.
Downloaded from www.Manualslib.com manuals search engine
CUSTOMIZING SETTINGS
NETWORK Settings
NETWORK
1 Press the SETTINGS button.
2 Use the , , , or button to select
yyNetwork Connection
yyNetwork Status
yySoft AP
yyWi-Fi Direct
NETWORK and press the OK button.
TM
yyMiracast
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
63
/ Intel's WiDi
yyMy Projector Name : PF80A-JE
Ͱ
The available network settings are described as follows.
Item
Description
Network
Connection
Connects a network.
Network Status
Displays the connection status of the network.
Soft AP
This function allows you to change a wired Internet connection
to your projector to Wi-Fi, allowing you to connect various
external devices or to use wireless Internet.
Soft AP
Sets to On/Off.
Security Key
Sets the Wi-Fi security number.
yyYou can set the security key with a
combination of English letters and
numbers between 8 and 64 characters
long.
yyThe default setting is AR123456.
yyTo enable the Soft AP function, your projector must be turned
on and have a wired Internet connection.
yyUp to four external devices can be connected.
yyIf the Soft AP function is enabled, the Wi-Fi Direct and
MiracastTM functions become unavailable. You must set the
Soft AP function to Off to use the Wi-Fi Direct and MiracastTM
functions.
Wi-Fi Direct
Wi-Fi Direct is a function that allows your projector to connect
with a Wi-Fi Direct device without Internet connection.
MiracastTM / Intel's The MiracastTM allows you to enjoy video and audio from a
WiDi
portable device through the projector wirelessly. Intel's WiDi
allows you to view a laptop screen through the projector without
a cable.
My Projector
Name
Changes the name that appears when searching for the
projector from other devices.
Downloaded from www.Manualslib.com manuals search engine
64
CUSTOMIZING SETTINGS
SUPPORT
1 Press the SETTINGS button.
2 Use the , , , or button to select
Ͱ SUPPORT
yySoftware Update
yyProduct/Service Info.
SUPPORT and press the OK button.
yySelf Diagnosis
3 Use the
, , , or button to set up the
desired item and press the OK button.
- To return to the previous menu, press the
button.
Ͱ
The available support settings are described as follows.
Item
Software Update
Description
Updates to the latest software.
Product/Service Info. Shows the product/service information.
Self Diagnosis
Downloaded from www.Manualslib.com manuals search engine
Troubleshoots functional problems that can arise while using
the product.
CONNECTING DEVICES
65
CONNECTING DEVICES
You can connect various external devices to the projector.
Computer/Notebook
USB
Digital Device
LG Audio Device
Game Console
Headphones
Mobile Phone
HDMI - page 66
Composite ��������������
(AV) - page 67
Component - page 68
USB Devices - page 35
Headphones - page 68
Digital Amp - page 69
Mobile Phone - page 71
Downloaded from www.Manualslib.com manuals search engine
Video/DVD
66
CONNECTING DEVICES
Connecting to HD
Receiver, DVD, VCR,
or External Devices
Connect an HD receiver, DVD, VCR
player, or External Devices to the
projector and select an appropriate input
mode.
HDMI Connection
With an HDMI cable, you can enjoy high
quality picture and sound.
Using a HDMI cable, connect the HDMI
IN 1 (ARC) port of the projector to
the HDMI output port of the device to
connect. Both video and audio is output
at the same time. You can also use the
HDMI IN 2 (MHL).
Press the INPUT button on the remote
control to select HDMI. You can connect
with any HDMI input port.
* Optional
Extras
+'0,
Downloaded from www.Manualslib.com manuals search engine
NOTE
ARC (Audio Return Channel)
yyExternal audio devices that
support SIMPLINK and ARC must
be connected using HDMI IN 1
(ARC) port.
yyWhen connected with a highspeed HDMI® cable, external
audio devices that support ARC
output or SPDIF work with the
SIMPLINK function without the
need for an additional optical
audio cable.
CONNECTING DEVICES
67
HDMI to DVI Connection
AV Connection
Using an HDMI to DVI cable, connect
the projector's HDMI IN 1 (ARC) port to
the DVI OUT port. You can also use the
HDMI IN 2 (MHL).
To output audio, use an audio cable for
connection.
Press the INPUT button on the remote
control to select HDMI. You can connect
with any HDMI input port.
Connect the output ports of an external
device and the AV IN ports of the
projector using an AV cable. Press the
INPUT button on the remote control to
select AV.
Check whether cables of the same color
are connected properly.
* Accessories
RED
* Optional
Extras
WHITE
Extras
YELLOW
* Optional
RED
WHITE
YELLOW
* Optional
Extras
AUDIO OUT
DVI OUT
Downloaded from www.Manualslib.com manuals search engine
RED
WHITE
YELLOW
$9287
/HIW
5LJKW
$8',2287
68
CONNECTING DEVICES
Component Connection
You can enjoy a video by connecting the
Component port of an external device
to the COMPONENT IN port of the
projector. Press the INPUT button on the
remote control to select Component.
Check whether cables of the same color
are connected properly.
* Optional
* Accessories
Extras
(Audio)
(Video)
RED
RED
* Optional
Extras
(Audio)
3%
$9287
35
$9287
/HIW /HIW 5LJKW5LJKW
$8',2287
$8',2287
Downloaded from www.Manualslib.com manuals search engine
RED
WHITE
RED
BLUE
GREEN
<
RED
RED
BLUE
WHITE
BLUE
GREEN
WHITE
GREEN
* Optional
Extras
(Video)
Connecting to
Headphones
You can listen to the audio through a
headphone.
* Optional
Extras
CONNECTING DEVICES
Connecting a Digital
Amp
Using an optical cable, connect the
digital audio input port of a digital amp
to the OPTICAL DIGITAL AUDIO OUT
port of the projector. The output of an
amp with a digital converter must be set
to the desired audio format. When using
a HDMI cable to connect a home theater
or when connecting an optical output
to an external audio device, set Sound
Out to External Speaker (Optical/HDMI
ARC) as shown below. If a projector,
home theater, or the speaker of an
external audio device is operating at the
same time, there will be an echo.
* Optional
Extras
Downloaded from www.Manualslib.com manuals search engine
NOTE
yyAlso, refer to the user manual of
the audio device to connect.
yyWhen connecting this product to
other devices, make sure to turn
off and unplug all the devices.
yyThe audio output of this
product has wide-ranging audio
bandwidth, so the receiver
volume must be adjusted
properly.
Speakers can be damaged by
unexpected high frequencies.
yyConnecting the OPTICAL
DIGITAL AUDIO OUT port of
the projector to the digital audio
input port of a digital amp and the
audio input port of the projector
to the analog audio output port of
the digital amp can cause sound
oscillation due to the closed
loop. Remove one of the two
connections to prevent this.
(This also applies to home theater
devices.)
69
70
CONNECTING DEVICES
Connecting to PC and
Laptop
The projector supports Plug & Play. Your
PC will automatically detect the projector
and requires no driver installation.
You can connect the projector to a
laptop to use various functions.
HDMI Connection
Using an HDMI cable, connect the HDMI
IN 1 (ARC) port of the projector to the
HDMI output port of your PC. Both video
and audio is output at the same time.
You can also use the HDMI IN 2 (MHL).
The table below shows examples
of switching the output. For more
information, refer to the External
Output, Connecting to an External
Monitor, or similar sections of the
owner's manual of your computer.
Brand
Switching Output
NEC
[Fn]+[F3]
Panasonic
[Fn]+[F3]
Toshiba
[Fn]+[F5]
IBM
[Fn]+[F7]
Sony
[Fn]+[F7]
Fujitsu
[Fn]+[F10]
LG
[Fn]+[F7]
Samsung
[Fn]+[F4]
Macintosh Adjust the control panel
to enable mirroring after
start-up.
* Optional
Extras
+'0,
Downloaded from www.Manualslib.com manuals search engine
CONNECTING DEVICES
Using the Mirroring Function of a Mobile Phone
MHL Connection
The Mobile High-definition Link (MHL) is an interface that can connect a mobile
phone to the projector and play video and audio from the mobile phone through the
projector.
This only applies to products with a HDMI input that supports MHL.
(To find out whether your device is MHL-certified, please contact your device
manufacturer.)
For MHL support, check the HDMI IN 2 (MHL) port.
Use a dedicated cable for MHL.
* Optional Extras
NOTE
yyWhen you connect a mobile phone to the HDMI IN 2 (MHL) port, you can see
the mobile phone screen through a projector.
- This only applies to mobile phones that support MHL.
- You can use the remote control for some applications.
yyDisconnect the MHL cable from the projector when:
- The MHL function is disabled.
- Your mobile device is fully charged in standby mode.
Downloaded from www.Manualslib.com manuals search engine
71
72
MAINTENANCE
MAINTENANCE
Clean your Projector to keep it in optimal condition.
Cleaning
Cleaning the Lens
If there is any dust or staining on the lens surface, you must clean the lens.
Use an air spray or a cleaning cloth to clean the lens.
To remove dust or stains, use an air spray or apply a small amount of cleaning agent
onto a swab or soft cloth to lightly rub the lens.
Please be aware that liquid may flow into the lens if the product is sprayed directly onto
the lens.
Cleaning the Projector Case
To clean the projector case, first unplug the power cord.
To remove dust or stains, use only a dry, lint-free, nonabrasive cloth to polish the lens.
Do not use alcohol, benzene, thinners, or other chemicals, which may damage the
case.
Downloaded from www.Manualslib.com manuals search engine
INFORMATION
INFORMATION
To Update Projector Software
Uses Software Update to check and obtain the latest version.
It is also possible to check manually for available updates.
1 Press the SETTINGS button.
2 Select SUPPORT and go to Software Update.
Item
Description
Software Update
Set it to On.
If an update is available, a prompt will appear to perform
the update.
Automatic update
mode
If an update is available, the update automatically starts
without prompting.
Check Update Version
Checks the latest update version installed. When a
new update is available, the download process can be
performed manually.
yyWhen the update starts, the update progress window appears for a short time and
disappears.
yyThe update service to get the latest version is provided through an Internet
connection.
yyIf software is not updated, certain functions may not work properly.
Downloaded from www.Manualslib.com manuals search engine
73
74
SPECIFICATIONS
SPECIFICATIONS
Model
PF80A (PF80A-JE)
Resolution (Pixel)
Aspect ratio
Panel size (mm)
Projection distance
(Video size)
Ratio of upward
projection
Working range of
the remote control
POWER
Audio output
1920 (Horizontal) × 1080 (Vertical)
16:9 (Horizontal:Vertical)
16.654
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
USB Device
Operation
environment
0.63 m - 3.72 m (50.8 cm - 304.8 cm)
100 %
6m
AC 100 ~ 240 V, 50 Hz/ 60 Hz
5W+5W
Min. 45.9 (without foot),
Max. 55.3 (without foot), 56.9 (with foot)
275.0
219.0 (without lens), 226.0 (with lens)
2.2
5 V, 0.5 A (Max.)
Temperature
Operation
0 °C to 40 °C
Storage
-20 °C to 60 °C
Relative humidity
Operation
0 % - 80 %
Storage
0 % - 85 %
* Contents in this manual may be changed without prior notice due to upgrade of
product functions.
Downloaded from www.Manualslib.com manuals search engine
SPECIFICATIONS
HDMI (DTV) supported mode
Resolution
720 x 480
720 x 576
1280 x 720
1920 x 1080
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.469
75
HDMI (PC) supported mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
59.94
640 x 480
31.469
59.94
31.50
60.00
800 x 600
37.879
60.31
31.25
50
1024 x 768
48.363
60.00
37.5
50
1152 x 864
54.348
60.053
44.96
59.94
1360 x 768
47.712
60.015
45.00
60.00
1280 x 1024
63.981
60.020
28.125
50
1920 x 1080
67.5
60.00
33.72
59.94
33.75
60.00
26.97
23.97
27.000
24.000
28.125
25
33.716
29.976
33.75
30.00
56.25
50
67.43
59.94
67.500
60
Downloaded from www.Manualslib.com manuals search engine
yyIf an invalid signal is input into the
projector, it will not be displayed
properly on the screen or a message
such as No Signal or Invalid Format
will be displayed.
yyThe projector supports the DDC1/2B
type as the Plug & Play function
(Auto-recognition of PC monitor).
yyThe 1920 x 1080 resolution may not
be supported depending on the PC
type.
76
SPECIFICATIONS
Component Supported Mode
Resolution
720 x 480i
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
15.73
59.94
15.75
60.00
31.47
59.94
31.5
60
720 x 576i
15.625
50
720 x 576p
31.25
50
37.5
50
44.96
59.94
45.00
60.00
28.125
50
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
28.125
25.00
33.71
29.97
33.75
30.00
56.25
50.00
67.432
59.94
67.500
60.00
720 x 480p
1280 x 720p
1920 x 1080i
1920 x 1080p
Downloaded from www.Manualslib.com manuals search engine
Component Port Connecting
Information
Component
ports on the
Projector
Video output
ports on DVD
player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
SPECIFICATIONS
Open Source Software Information
To obtain the source code under GPL,
LGPL, MPL and other open source
licenses, that is contained in this
product,
please visit http://opensource.lge.com.
In addition to the source code, all
referred license terms, warranty
disclaimers and copyright notices are
available for download.
LG Electronics will also provide open
source code to you on CD-ROM for a
charge covering the cost of performing
such distribution (such as the cost of
media, shipping and handling) upon
email request to [email protected]
This offer is valid for three (3) years from
the date on which you purchased the
product.
Downloaded from www.Manualslib.com manuals search engine
77
The model and serial number of the projector
are located on the back or on the side of the
projector. Record them below should you ever
need service.
MODEL
SERIAL
Downloaded from www.Manualslib.com manuals search engine
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement