null  null
PlasmaSync 42XC10
PlasmaSync 50XC10
PlasmaSync 60XC10
Downloaded From TV-Manual.com Manuals
English
User’s Manual
Package Contents
• Plasma Monitor
• Remote control and AA Batteries
• Power cord
• Users Manual (CD-ROM)
• Start Up Guide (Paper / CD-ROM)
• Main Power Switch cover and screw
• Cable clamps
Downloaded From TV-Manual.com Manuals
Table of Contents
Important Safety Instructions ..............................................................................................................English-1
Important Information ...........................................................................................................................English-2
Safety Precautions and Maintenance ...................................................................................................English-3
Recommended Use ....................................................................................................................................English-4
Installation
Optional Stands/Mounts ..........................................................................................................English-6
Mounting Location ....................................................................................................................English-6
Mounting on Ceiling ..................................................................................................................English-7
Maintenance, Orientation, Cable Management ..................................................................English-7
Using the Remote ......................................................................................................................English-8
Part Names and Functions
Control Panel ..............................................................................................................................English-9
Terminal Panel ............................................................................................................................English-10
Remote Control ..........................................................................................................................English-11
Power, Display, Digital Zoom, Pointer, Main Power Switch Cover .....................................English-12
Remote Control ID .....................................................................................................................English-13
On-Screen Display (OSD)
Using the OSD .............................................................................................................................English-14
OSD................................................................................................................................................English-15
Operation
Picture Size Using Video Signals ............................................................................................English-18
Picture Size Using Computer Signals ....................................................................................English-19
Split Screen Mode .....................................................................................................................English-20
Picture-in-Picture Mode .........................................................................................................English-21
RS-232C .......................................................................................................................................................English-23
Troubleshooting.........................................................................................................................................English-27
Specifications
42XC10..........................................................................................................................................English-28
50XC10 .........................................................................................................................................English-29
60XC10 .........................................................................................................................................English-30
Supported Resolutions
42XC10..........................................................................................................................................English-31
50XC10 .........................................................................................................................................English-33
60XC10 .........................................................................................................................................English-35
Pin Assignment ..........................................................................................................................................English-37
Downloaded From TV-Manual.com Manuals
13. Unplug this apparatus during lightning storms or when
unused for long periods of time
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped
16. Damage Requiring Service -The appliance should be
serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into
the appliance;
or
C. The appliance has been exposed to rain;
or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance;
or
E. The appliance has been dropped, or the enclosure
damaged.
17. Tilt/Stability - All monitors must comply with
recommended international global safety standards for
tilt and stability properties of its cabinet design.
Do not compromise these design standards by applying
excessive pull force to the front, or top, of the cabinet
which could ultimately overturn the product.
Also, do not endanger yourself, or children, by placing
electronic equipment/toys on the top of the cabinet.
Such items could unsuspectingly fall from the top of the
set and cause product damage and/or personal injury.
18. Wall/Ceiling Mounting - The appliance should be
mounted to a wall/ceiling only as recommended by the
manufacturer.
19. Power Lines - An outdoor antenna should be located
away from power lines.
20. Outdoor Antenna Grounding - If an outside antenna is
connected to the receiver, be sure the antenna system
is grounded so as to provide some protection against
voltage surges and built up static charges.
Section 810 of the National Electric code. ANSI/NFPA
No.70-1984, provides information with respect to
proper grounding of the mats and supporting structure,
grounding of the lead-in wire to an antenna-discharge
unit, size of grounding connectors, location of antenna
discharge unit, connection to grounding electrodes and
requirements for the grounding electrode.
21. Objects and Liquid Entry - Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
Apparatus shall not be exposed to dripping or splashing
and no objects fi lled with liquids, such as vases, shall be
placed on apparatus
Additional Safety Information
WARNING
Read Before Operating Equipment.
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and third grounding prong The wide
blade or third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart or apparatus combination to avoid
injury from tip-over.
15. This product may contain lead. Disposal of these
materials may be regulated due to environmental
considerations.
For disposal or recycling information, please contact
your local authorities or the Electronic Industries
Alliance: www.eiae org.
To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture.
English-1
Downloaded From TV-Manual.com Manuals
English
Important Safety Instructions
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been
included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC
voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
North America
European
Continental
U.K.
Chinese
Japanese
Country
U.S.A./Canada
EU (except U.K.)
U.K.
China
Japan
Voltage
120*
230
230
220
100
Plug Type
Plug Shape
*When operating the PlasmaSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power
supply voltage of the AC power outlet being used.
measures:
Canadian Department of
Communications Compliance Statement
• Reorient or relocate the receiving antenna.
DOC: This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
• Increase the distance between the equipment and
receiver.
FCC Information
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
1. Use the attached specified cables with the P426Y3(P42XC10),
P506Y4(P50XC10) or P606Y5(P60XC10) color monitor so as not to
interfere with radio and television reception.
If necessary, the user should contact the dealer or an experienced radio/
television technician for additional suggestions. The user may find the
following booklet, prepared by the Federal Communications Commission,
helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This
booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
(1) Please use the supplied power cord or equivalent to
ensure FCC compliance.
(2) Please use shielded video signal cable,
15-pin mini D-SUB to 15-pin mini D-SUB
with ferrite cores on both ends (not included).
WARNING
This product equipped with a three-wire grounding (earthed) plug - a plug
that has a third (grounding) pin. This plug only fits a grounding-type power
outlet. If you are unable to insert the plug into an outlet, contact a licensed
electrician to replace the outlet with a properly grounded one. Do not defeat
the safety purpose of the grounding plug.
2. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
English-2
Downloaded From TV-Manual.com Manuals
• Unplug the power cord during electrical storms or when
the unit will not be in use for a long period.
• Do not use monitor in high temperature, humid, dusty,
or oily areas.
• Do not cover vent on monitor.
• Clean plasma ventilation areas using a vacuum cleaner
with a soft brush nozzle attachment.
• To ensure proper ventilation, cleaning the ventilation
areas must be carried out monthly. More frequent
cleaning may be necessary depending on the
environment in which the plasma monitor is installed.
• Allow adequate ventilation around the monitor so that
heat can properly dissipate. Do not block ventilated
openings or place the monitor near a radiator or other
heat sources. Do not put anything on top of monitor.
• Handle with care when transporting. Save packaging for
transporting.
• As is the case with any phosphor-based display (like a
CRT monitor, for example) light output will gradually
decrease over the life of a Plasma Display Panel.
• To avoid sulfurization it is strongly recommended not to
place the unit in a dressing room in a public bath or hot
spring bath.
Safety Precautions
and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND
USING THE MONITOR:
The plasma display's panel is made up of fine picture
elements (cells), of which more than 99.99 percent are active
cells. Some cells may not produce light or remain constantly
lit. For safe operation and to avoid damaging the unit, read
carefully and observe the following instructions.
• DO NOT OPEN THE MONITOR. There are no userserviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other
risks. The manufacturer is not liable for any bodily harm
or damage caused if unqualified persons attempt service
or open the back cover. Refer all servicing to qualified
service personnel.
• Do not spill any liquids into the cabinet or use your
monitor near water.
• Do not insert objects of any kind into the cabinet slots,
as they may touch dangerous voltage points, which can
be harmful or fatal or may cause electric shock, fire or
equipment failure.
• Do not bend, crimp or otherwise damage the power cord.
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
• Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
• Do not use in a moving vehicle, as the unit could drop or
topple over and cause injuries.
• The power cable connector is the primary means of
detaching the system from the power supply. The
monitor should be installed close to a power outlet that
is easily accessible.
• This equipment shall be connected to a MAIN outlet
with a protective earth-ground connection. Do not place
any objects onto the monitor and do not use the monitor
outdoors.
• Do not use this unit’s polarized plug with an extension
cord or with outlets unless the prongs can be inserted
fully.
• The power supply cord you use must have been approved
by and comply with the safety standards of your
country. (Type H05VV-F 3G 1mm2 should be used in
Europe)
• In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this
monitor.
• Use only with 100 V to 240 V 50 Hz/60 Hz AC power
supply. Continued operation at line voltages greater than
100 V to 240 V AC will shorten the life of the unit, and
might even cause a fire hazard.
CAUTION
Immediately unplug your monitor from the wall outlet and
refer servicing to qualified service personnel under the
following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled on, or objects have fallen into
the monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet
damaged.
• If the monitor does not operate normally by following
operating instructions.
English-3
Downloaded From TV-Manual.com Manuals
English
Safety Precautions and Maintenance
Recommended Use
CAUTION
Cleaning the Panel
• When the panel becomes dusty or dirty, wipe gently
with soft cloth.
• Do not rub the panel with coarse material.
• Do not apply pressure to the surface.
• Do not use OA cleaner. OA cleaner will cause
deterioration or discolor the surface.
CORRECT PLACEMENT AND ADJUSTMENT OF
THE MONITOR CAN REDUCE EYE, SHOULDER AND
NECK FATIGUE. CHECK THE FOLLOWING WHEN
POSITIONING THE MONITOR:
• For optimum performance, allow 20 minutes for warmup.
• Rest your eyes periodically by focusing on an object at
least 5 feet away. Blink often.
• Position the monitor at a 90 degree angle to windows
and other light sources to minimize glare and
reflections.
• Clean the monitor surface with a lint-free, nonabrasive
cloth. Avoid using any cleaning solution or glass
cleaner.
• Adjust the monitor’s brightness and contrast controls to
enhance readability.
• Get regular eye checkups.
Cleaning the Cabinet
• Unplug the power supply.
• Gently wipe the cabinet with a soft cloth.
• To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a
dry cloth.
NOTE:The surface of the cabinet is composed of many
types of plastic.
DO NOT clean with benzene thinner, alkaline
detergent, alcoholic system detergent, glass cleaner,
wax, polish cleaner, soap powder, or insecticide.
Rubber or vinyl should not be in contact with
the cabinet for an extended period of time. These
types of fluids and materials can cause the paint to
deteriorate, crack or peel.
Ergonomics
To realize the maximum ergonomic benefits, we recommend
the following:
• Use the preset Size and Position controls with standard
signals.
• Use the preset Color Setting.
• Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
• This equipment is not for use at video display work
station according to Bildscharb V.
CLEANING THE VENT HOLES
• Clean plasma ventilation areas using a vacuum cleaner
with a soft brush nozzle attachment.
• To ensure proper ventilation, cleaning the ventilation
areas must be carried out monthly. More frequent
cleaning may be necessary depending on the
environment in which the plasma monitor is installed.
For more detailed information on setting up a healthy work
environment, refer to the following document:
American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations
ANSI-HFS Standard No. 100-1988
Published by:
The Human Factors and Ergonomics Society
P.O. Box 1369, Santa Monica, California 90406.
English-4
Downloaded From TV-Manual.com Manuals
Recommended Use - continued
OPERATING ENVIRONMENT
Operating environment temperature and humidity: 0 °C to
+40 °C (+32 °F to +104 °F); less than 80%RH (cooling vents
not blocked) Do not install this unit in a poorly ventilated
area, or in locations exposed to high humidity or direct
sunlight (or strong artificial light)
Like all phosphor-based display devices and all other gas
plasma displays, plasma monitors can be susceptible to image
retention under certain circumstances. Certain operating
conditions, such as the continuous display of a static
image over a prolonged period of time, can result in image
retention if proper precautions are not taken. To protect
your investment in this plasma monitor, please adhere to the
following guidelines and recommendations for minimizing
the occurrence of image retention:
WARNING
Not for use in a computer room as defined in the Standard
for the Protection of Electronic Computer/Data Processing
Equipment ANSI/NFPA 75.
NOTE: Please use shielded video signal cable, 15-pin mini
D-SUB to 15-pin mini D-SUB with ferrite cores on
both ends (not included).
• Always enable and use your computer’s screen saver
function during use with a computer input source.
• Display a moving image whenever possible.
• Change the position of the menu display from time to
time.
• Always power down the monitor when you are finished
using it.
To reduce the likelihood of
image retention from long-term
use:
• Lower the Brightness and Contrast levels as much as
possible without impairing image readability.
• Display an image with many colors and color gradations
(i.e. photographic or photo-realistic images).
• Create image content with minimal contrast between
light and dark areas. Use complementary or pastel colors
whenever possible.
• Avoid displaying images with few colors and distinct,
sharply defined borders between colors.
Plasma monitor driving sound
• The panel of the Plasma monitor is composed of
extremely fine pixels and these pixels emit light
according to received video signals. This principle may
cause you to hear a buzz or electrical hum coming from
the Plasma monitor. Also note that the rotation speed
of the cooling fan motor increases when the ambient
temperature of the Plasma monitor becomes high. You
may hear the sound of the motor at that time.
NOTE: The following items are not covered by the
warranty.
• Image retention
• Panel generated sound. Examples: Fan motor
and electrical noises circuit humming /glass panel
buzzing.
English-5
Downloaded From TV-Manual.com Manuals
English
To avoid or minimize image
retention:
Installation
• Allow adequate ventilation or provide air conditioning
around the monitor, so that heat can properly dissipate
away from the unit and mounting apparatus.
Using Optional Stand/Mounts
An optional stand or mounting apparatus can be installed
either while the unit is in the upright position or while the
unit is face-down.
Figure 1
To install the stand while in the upright position, lower the
monitor onto to the feet as shown (Figure 1). Use the handles
to support the display while lowering the support holes
underneath the display onto the feet.
If stand or mounting apparatus is to be installed while the
unit is face-down (Figure 2), be sure to lay the protective
sheet (the foam sheet that the unit was wrapped in)
underneath the unit on order to prevent damage to the
screen.
This unit must be used with a stand or some type of
mounting apparatus. This unit is not designed for use
without additional support.
• For correct Installation and Mounting it is
recommended to use a trained, authorized dealer.
• Failure to follow correct mounting procedures could
result in dame to the unit or to the installer.
• Product warranty does not cover damage caused by
improper installation.
Protective Sheet
Figure 2
CAUTION:
• To install, follow those instructions included with the
stand or mounting apparatus. Use only those devices
recommended by the manufacturer.
• Make sure to install stand or mounting apparatus to the
unit while on a surface that is strong and stable enough
to support the weight of the unit, such as a floor or
sturdy table.
• Use the specified clasps for installation.
• Take necessary steps to prevent the unit from tipping or
falling.
Table
Mounting Location
Figure 3
• DO NOT install in locations where a door or gate can hit
the unit.
• DO NOT install in areas where the unit will be subjected
to strong vibrations and dust.
• DO NOT install near where the main power supply
enters the building.
• DO NOT install in where people can easily grab and
hang onto the unit or the mounting apparatus.
• When mounting in an enclosure or in a recessed area, as
in a wall, leave at least 2 inches (50mm) of space between
the monitor and the wall for proper ventilation (Figure 3).
50mm (2")
English-6
Downloaded From TV-Manual.com Manuals
50mm (2")
50mm (2")
50mm (2")
50mm (2")
The ceiling and wall must be strong enough to support the
monitor and mounting accessories.
Installation - continued
Cable Management
To conveniently manage cables, use the cable clamps
provided to bundle the power cord together with the signal
and audio cables at the back of the display.
• Ensure that the ceiling is sturdy enough to support the
weight of the unit and the mounting apparatus over
time, against earthquakes, unexpected vibrations, and
other external forces.
• Be sure the unit is mounted to a solid structure within
the ceiling, such as a support beam. Secure the monitor
using bolts, spring lock washers, washer and nut.
• DO NOT mount to areas that have no supporting
internal structure. DO NOT use wood screws or anchor
screws for mounting. DO NOT mount the unit to trim
or to hanging fi xtures.
To attach cable clamps:
1. Attach the cable clamps to the display. Insert the anchor
of the clamp into the hole on the back of the display.
There are 4 cable clamps and 4 clamp holes on the unit.
2. After the cable clamp is positioned on the display, wrap
the end around the cables. Place the end of the clamp
into the slot near the anchor. Pull until cables are snug.
Clamps are designed to stay in place. Once in position,
they will be difficult to remove.
Maintenance
3. Cables can be routed to the right or left of the clamp.
Use the beaded bands to secure the cables together along
their length. Make sure the cables are fully supported.
• Periodically check for loose screws, gaps, distortions,
or other problems that may occur with the mounting
apparatus. If a problem is detected, please refer to
qualified personnel for service.
• Regularly check the mounting location for signs of
damage or weakness that may occur over time.
To detach clamps:
Using pliers, twist the clamp 90 degrees and pull
outward. It is possible that the clamp can weaken over
time and removing it may cause damage to the clamp.
Please note the following when
mounting on wall or ceiling.
• When using mounting accessories other than those that
are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method.
• NEC strongly recommends
Mounting
Unit
Bracket
using size M8 screws
(16mm + thickness of
bracket in length). If using
screws longer than 16mm,
Screw
check the depth of the
16mm
hole.(Recommended Fasten
Thickness
Force: 1125 - 1375N•cm)
of Bracket
NEC recommends mounting
interfaces that comply with
Screw length should equal
UL1678 standard in North
depth of hole (16mm) + the
thickness of mounting bracket.
America.
Anchor
Orientation
DO NOT use this monitor in the
portrait position. Doing so may cause
failure and void the warranty.
English-7
Downloaded From TV-Manual.com Manuals
Slot
Holes for Clamp
anchors
Closed Clamp
English
Mounting on Ceiling
Installation - continued
Operating Range for the Remote Control
Using the Remote:
Point the top of the remote control toward the monitor’s
remote sensor while pressing buttons. The remote control
can be used from the front of the monitor at a maximum
distance of 7 m/23 ft. from the front of the Plasma monitor’s
remote control sensor. The maximum horizontal and vertical
angle for use of the remote is 30 degree within a distance of
3.5 m/11.5 ft.
Install the remote control batteries.
The remote control is powered by AA batteries. To install or
replace batteries:
CAUTION
The remote control may not function when direct sunlight
or strong illumination strikes the remote control sensor of
the Plasma monitor, or when there is an object in the path of
the sensor.
A. Press and slide to open the cover.
B. Align the batteries according to the (+)
and (–) indications inside the case.
C. Replace the cover.
Handling the Remote Control
Do not open the remote control other than to install
batteries. Do not allow water or other liquid to splash onto
the remote control. If the remote control gets wet, wipe it dry
immediately.
Avoid exposure to heat and steam.
CAUTION: Incorrect usage of batteries can result in leaks or
bursting. NEC recommends the following battery use:
• Place “AA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
• Do not mix battery brands.
• Do not combine new and old batteries, or mix brands.
This can shorten battery life or cause liquid leakage of
batteries.
• Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
• Do not touch exposed battery acid, it may injure skin.
• Do not drop or mishandle the remote.
• Do not get the remote control wet. If the remote does get
wet, wipe dry immediately.
• Avoid excessive heat and humidity.
• Do not dispose of batteries in fire.
• Please follow government regulations or public
environmental rules that apply in your country/area
when disposing of used batteries.
• When replacing, use only conventional nonrechargeable alkaline or manganese batteries.
• There is a risk of explosion if batteries are replaced
incorrectly.
NOTE: If you do not intend to use the Remote Control for a
long period of time, remove the batteries.
30
English-8
Downloaded From TV-Manual.com Manuals
30
Part Names and Functions
English
Control Panel
9
ON
OFF
10
8
7
6
5
1) POWER
Switches the power on/standby.
4
3
2
1
8) EXIT
Activates the OSD menu when the OSD menu is off.
Exits from the current menu being displayed to the
previous menu within the OSD.
2) MUTE
Switches the audio mute ON/OFF.
9) Remote control sensor and Power indicator
Receives the signal when using the wireless remote control.
Glows green when the monitor is active. Glows red when
the monitor is in Standby mode. Glows Amber when the
monitor is in POWER SAVE mode.
3) INPUT
Switches between input sources.
Acts as SET button within the OSD menu.
4) PLUS (+)
Increases the setting adjustment within OSD menu.
A red blinking Power indicator means that the monitor has
detected a failure. Contact qualified personnel in case of
failure.
5) MINUS (-)
Decreases the setting adjustment within OSD menu.
10) Main Power Switch
Seesaw switch to turn the main power on/off.
6) UP ( )
Increases the volume level when the OSD is off.
Moves area up to select which setting to is to be adjusted
within OSD menu.
Mode
7) DOWN ( )
Decreases the volume level when the OSD is off.
Moves down to select which setting is to be adjusted within
OSD menu.
Status indicator light
Power On
Green
Standby
Red
Power save
Amber
Diagnosis
(Detecting failure)
Red blinking
NOTE:
The POWER button does not completely turn off the
display. Use the Main Power Switch to completely turn off
the display.
English-9
Downloaded From TV-Manual.com Manuals
Part Names and Functions
Terminal Panel
9
1
DVD/HD2
OUT
R
R
IN
EXTERNAL CONTROL
2
12
L(MONO)
L(MONO)
DVD/HD3
DVI
3
4
AUDIO3
5
R
Y
Cr/Pr Cb/Pb
L(MONO)
VGA
AUDIO2
DVD/HD1
AUDIO1
6
7
8
10
1) EXTERNAL CONTROL OUT (D-Sub 9 pin)
Connect RS-232C output to a second monitor.
2) EXTERNAL CONTROL (D-Sub 9 pin)
Connect RS-232C input to external equipment such as a
PC in order to control RS-232C functions.
3) DVD/HD3 (HDMI)
Input digital HDMI signals.
IN
R
L
S-VIDEO IN
VIDEO
11
SPEAKER (S)
AC IN
13
14
8) DVD/HD1
Connect equipment such as a DVD player, HDTV device,
or set-top box.
9) DVD/HD2
Connect equipment such as a DVD player, HDTV device
or set-top.
10) AUDIO1
Input the audio signal from external equipment such as a
computer, VCR or DVD player.
4) DVI
Input digital RGB signals from a computer or HDTV
device having a digital RGB output.
5) AUDIO3
Input the audio signal from external equipment such as a
computer, VCR or DVD player.
6) VGA (Mini D-Sub 15 pin)
Analog computer input.
7) AUDIO2
Input the audio signal from external equipment such as a
computer, VCR or DVD player.
11) S-VIDEO in
Input S-video.
12) VIDEO1
Composite video input.
13) EXTERNAL SPEAKER (L and R) connector
Connects to optional speakers. Output the audio signal
from AUDIO 1, 2, and 3 to external speakers.
NOTE: Speaker Terminal is for 8W + 8W (8 ohm).
14) AC IN
Connects with the supplied power cord.
Information:
For SCART connections there are 2 ways to connect:
SCART1: Connect R/G/B to the DVD/HD1 terminals and
composite sync. to the VIDEO1 terminal.
SCART2: Connect R/G/B + composite sync. to the VGA
terminal.
English-10
Downloaded From TV-Manual.com Manuals
Remote Control Functions
RGB
4
5
7) KEYPAD
Set REMOTE ID.
STANDBY
POWER ON
1
2
3
6) SIZE
Set the aspect ratio of the image.
DVD/HD
VIDEO
8) DISPLAY
Turn on/off the Information OSD.
PICTURE
MEMORY
22
PICTURE
MODE
SIZE
9)
6
Move selection up or down
1
2
3
4
5
6
7
8
9
10) AUTO SETUP
Adjusts the CLOCK PHASE, CLOCK, and POSITION
settings automatically. (Analog RGB signal input only)
7
11) POINTER
Turn on/off the pointer.
0
DISPLAY
MENU
8
15
9
SET
AUTO
SET UP
10
11
12) VOLUME
Increases/Decreases sound level.
16
17
+
13) SPLIT SCREEN
PIP: Picture-in-Picture mode.
S BY S: Side-by-side mode.
SINGLE: Returns to normal mode.
SWAP: Swaps the Split Screen images.
SELECT/FREEZE: Selects which input is active when
in split screen mode.
EXIT
18
VOL
+
ZOOM
POINTER
+
19
MUTE
12
SPLIT SCREEN
PIP
S BY S
20
SINGLE
13
SWAP
SELECT/FREEZE CAPTURE
REMOTE ID
SET
RESET
When the PICTURE FREEZE function (see OSD
FUNCTION) is operating, SELECT/FREEZE can be
used to display still pictures on the sub screen.
SLEEP
14
21
CAPTURE : Captures still picture.
REMOTE CONTROLLER RU-M113
14) REMOTE ID
Activates REMOTE ID function.
1) POWER ON/STANDBY
Switches the power on/standby.
*If the Power Indicator on the display is not glowing,
then no controls will work.
15) MENU
Turns ON/OFF menu mode.
16) SET
Makes selection.
2) VIDEO
Switches the input signal to the VIDEO source.
17) - , +
Increases or decreases amount of adjustment.
3) RGB
Switches the input signal to the RGB source.
18) EXIT
Goes to the previous menu.
4) DVD/HD
Switches the input signal to the DVD/HD source.
19) ZOOM
Enlarges or reduces the picture.
5) PICTURE MODE
Selects Picture Mode: [STANDARD], [BRIGHT],
[CINEMA1], [CINEMA2], [DEFAULT].
STANDARD: for viewing in a bright room
BRIGHT: brighter picture than STANDARD
CINEMA1, 2: for viewing in a dark room, good for
movies
DEFAULT: factory default settings
20) MUTE
Mutes audio output.
21) SLEEP
Sleep timer.
22) PICTURE MEMORY
Switches memory settings from 1 to 6.
English-11
Downloaded From TV-Manual.com Manuals
English
Part Names and Functions - continued
Part Names and Functions - continued
Main Power Switch Cover
POWER
Included with the display is a cover for the Main Power
Switch. Use this cover to prevent the unit from being
inadvertently powered off.
To turn the unit ON and OFF:
1. Plug the power cord into an AC outlet.
Place the tab on the cable cover into the rectangular slot on
the display.
2. Press the Power button (on the unit).
The monitor's ON/STANDBY indicator turns red and
the unit will be in STANDBY mode.
Then using the screw provided, secure the cover to the
display.
3. Press the POWER ON button on the remote control. The
ON/STANDBY indicator will turn green when the unit
is active.
4. Press the STANDBY button (on the remote) or the
Power button (on the unit) to turn off the monitor.
DISPLAY
To check display settings press the DISPLAY button on the
remote. The screen changes each time the DISPLAY button is
pressed. Display information will disappear after 3 seconds.
ON
DIGITAL ZOOM
OFF
SLOT
Digital zoom can change the picture position or enlarge the
image on the screen.
TAB
1. Be sure ZOOM NAV function is off. Press the ZOOM
button (+ or -) to display the magnifying glass.
Press the ZOOM + button to enlarge the image.
Press the ZOOM - button to reduce the image.
Press the UP and DOWN or PLUS and MINUS buttons
to reposition the picture.
Main Power
Switch
Cover
2. Press the POINTER button to hide the pointer.
POINTER
Use the Pointer to point to a specific area on the screen.
Press the UP and DOWN or PLUS and MINUS buttons to
reposition the Pointer.
English-12
Downloaded From TV-Manual.com Manuals
Part Names and Functions - continued
English
Remote Control ID Function
REMOTE CONTROL ID
The remote control included with the display can be used
to control up to 26 individual monitors using what is
called the REMOTE CONTROL ID mode. The REMOTE
CONTROL ID mode works in conjunction with the Monitor
ID, allowing control of up to 26 individual monitors. For
example: if there are many monitors being used in the same
area, a remote control in normal mode would send signals to
every monitor at the same time Figure 1. Using the remote
in REMOTE CONTROL ID mode will only operate one
specific monitor within the group Figure 2.
TO SET REMOTE CONTROL ID:
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote works
Remote works
Remote works
Figure 1
Remote in Normal
mode or the REMOTE
ID is set to 0
While holding down the REMOTE ID SET button on the
remote control, use the KEYPAD to input the Monitor ID
(1-26) of the display to be controlled via remote. The remote
can then be used to operate the monitor having that specific
Monitor ID number.
When 0 is selected or when the remote control is in normal
mode, all monitors will be operated.
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote does
not work
Remote does
not work
Remote works
TO USE REMOTE CONTROL ID MODE
ID Mode - To enter ID Mode press the REMOTE ID SET
button and hold down for 2 seconds.
Normal Mode - To return to Normal Mode press the
REMOTE ID RESET button and hold down for 2 seconds.
In order for this feature to work properly, the display must be
assigned a Monitor ID number. The Monitor ID number can
be assigned under the SETUP menu in the OSD (See page
17).
Figure 2
Remote set up to
use Remote ID:3
If Monitor ID is set to “ALL” , monitor is controled by remote
control not depend on remote ID.
English-13
Downloaded From TV-Manual.com Manuals
On-Screen Display (OSD)
4. Change the setting or adjustment by pressing the + and
- buttons on the Control Panel or the Remote Control.
Using the OSD
Use the Remote Control or the control panel on the front
of the unit to enter the on-screen display menu to adjust
settings.
5. Press the EXIT button on the Remote Control, on the
Control Panel to return to the previous menu.
1. Press the MENU button on the remote or the EXIT
button on the Control Panel.
NOTE: Not all menu functions may be available. To access
all functions the Advanced OSD option must be
turned on in the ADVANCED OSD menu.
2. Use the up and down buttons to select the desired menu.
3. Press the SET button to select a sub-menu or item for
adjustment.
Press UP or DOWN
button to select
sub-menu.
Press SET.
Press UP, DOWN, PLUS,
or MINUS to select the
function or setting to be
adjusted.
Press MENU or EXIT.
Remote
Control
Control
Panel
Press UP or DOWN
button to select.
Press INPUT
button to decide.
Press UP, DOWN, PLUS,
or MINUS to select.
Press EXIT.
OSD Screen
VGA
VGA
FUNC.
SCREEN
FUNCTION
PICTURE
PICTURE MEMORY
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
NR
COLOR TEMP.
FILM MODE
PICTURE MODE
4&-
.&/64&-
FUNC.
SET UP
SCREEN
INFO
PICTURE
PICTURE MEMORY
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
TINT
NR
COLOR TEMP.
FILM MODE
PICTURE MODE
GAMMA
SET UP LEVEL
COLOR CONTROL
OFF
OFF
HIGH
ON
STANDARD
$-04&
4&-
ADVANCED OSD is OFF. Not all OSD functions will be
available when the ADVANCED OSD is off.
.&/64&-
SET UP
INFO
OFF
OFF
HIGH
ON
STANDARD
2.2
0%
$-04&
Advanced OSD is ON. All OSD functions are shown, but
some OSD functions may not be available.
English-14
Downloaded From TV-Manual.com Manuals
FUNCTION
Main Menu
Sub Menu
PICTURE
PICTURE MEMORY
Sub Menu2
Store picture menu settings and input terminal information. The
memory number is 1-6.
The "PICTURE MEMORY" screen appears when the SET button is
pressed on the "PICTURE MEMORY" MENU.
Explanation
Default
Reset
OFF
YES
CONTRAST
Adjusts the image brightness in relationship to the white level.
Press + or - to adjust.
50
YES
BRIGHTNESS
Adjusts the image brightness in relationship to the background.
Press + or - to adjust.
50
YES
SHARPNESS
Adjusts the crispness of the image. Press + or - to adjust.
50
YES
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
50
YES
TINT
Adjusts the tint of the screen. Press + or - to adjust.
50
YES
NR
Adjusts the amount of noise reduction. Press + or - to adjust.
OFF
YES
COLOR TEMP.
Adjusts the color temperature of the entire screen. A low
color temperature will make the screen reddish. A high color
temperature will make the screen bluish.
MIDDLE
YES
50
YES
50
YES
50
YES
Resets the factory default settings. Select "ON", then press the
SET button to reset.
OFF
YES
FILM MODE
Selects Film mode.
ON
YES
PICTURE MODE
Selects picture mode, [BRIGHT], [STANDARD], [CINEMA1],
[CINEMA2], [DEFAULT].
STANDARD: For watching in a bright room.
CINEMA1, 2: For watching in a dark room, especially good for
movies.
BRIGHT: Brighter picture than STANDARD.
DEFAULT: Restores factory default settings.
STANDARD
YES
GAMMA
Available only when
the Advanced OSD
function in the
FUNCTION menu is
enabled.
Select a display gamma for best picture quality.
2.1, 2.2, 2.3, 2.4: The picture becomes darker as the number
increases.
S: Special gamma for certain types of movies. Raises the dark
parts and lowers the light parts of the image. (S-Curve)
These values are approximate.
2.2
YES
SET UP LEVEL
Available only when
the Advanced OSD
function in the
FUNCTION menu is
enabled.
Adjusts the video black level.
VIDEO signal input only.
0%
YES
Adjusts the levels of the Red, Green, Blue, Yellow, Magenta and
Cyan.
VIDEO and DVD/HD 1/2 input only.
50
YES
WHITE BALANCE.
GAIN RED
GAIN GREEN
GAIN BLUE
RESET
COLOR CONTROL
Available only when
the Advanced OSD
function in the
FUNCTION menu is
enabled.
RED
GREEN
The "WHITE BALANCE" appears when the SET button is pressed
on the "COLOR TEMP." OSD menu.
GAIN RED/GREEN/BLUE: Adjusts the white level of the white
balance.
50
YES
BLUE
50
YES
YELLOW
50
YES
MAGENTA
50
YES
CYAN
50
YES
OFF
YES
RESET
Resets the factory default settings. Select "ON", then press the
SET button to reset.
English-15
Downloaded From TV-Manual.com Manuals
English
On-Screen Display (OSD)
On-Screen Display (OSD)
Main Menu
AUDIO
Sub Menu
Sub Menu2
Explanation
SET UP
Some functions
available only
when the
Advanced OSD
function in the
FUNCTION
menu is
enabled.
The
LANGUAGE
and ALL
RESET
functions
are always
available.
Reset
YES
BASS
Adjusts the low frequency sound. Press + or - to adjust.
0
TREBLE
Adjusts the high frequency sound. Press + or - to adjust.
0
YES
BALANCE
Adjusts the balance of L/R volume. Press + or - to adjust.
0
YES
AUDIO INPUT1
Select which audio input to use with the video source.
VIDEO1
YES
AUDIO INPUT2
DVD/HD1
YES
AUDIO INPUT3
VGA
YES
HDMI
YES
DVD/HD3 INPUT
SCREEN
Default
ASPECT MODE
Selects aspect ratio of the displayed image. Press + or - to select.
-
-
V-POSITION
Controls the vertical position of the image within the Display area
of the PDP.
Press + to move up. Press - to move down.
0
YES
H-POSITION
Controls the horizontal position of the image within the Display
area of the PDP.
Press + to move right. Press - to move left.
0
YES
V-HEIGHT
Adjusts the vertical size of the image.
0
YES
H-WIDTH
Adjusts the horizontal size of the image.
0
YES
AUTO PICTURE
ON: H-Position, V-Position, Clock and Clock Phase are adjusted
automatically.
OFF: H-Position, V-Position, Clock and Clock Phase are adjusted
manually.
VGA input only.
OFF
NO
CLOCK PHASE
Adjusts the visual “noise” on the image.
VGA input only.
0
YES
CLOCK
Press + to expand the width of the image on the right of the
screen.
Press - to narrow the width of the image on the left.
VGA input only.
0
YES
UNDER SCAN
Available only when
the Advanced OSD
function in the
FUNCTION menu is
enabled.
ON: UNDERSCAN is selectable in the ASPECT MODE menu.
OFF: UNDERSCAN item is not selectable in the ASPECT MODE
menu.
Video signal input only.
OFF
YES
LANGUAGE
Select the language used by the OSD.
DVD/HD1 INPUT
Selects whether to set the input of the DVD/HD1 connector.
COMPONENT : for Component input. (3BNC connectors)
SCART1 : for SCART input (3RCA connectors and VIDEO1 input)
(SCART1 available for Europe and World-Wide models only)
ENGLISH
NO
COMPONENT
YES
D-SUB INPUT
Selects whether to set the input of the mini D-SUB connector.
RGB : for RGB input
SCART2 : for SCART input
(SCART2 available for Europe and World-Wide models only)
RGB
YES
HD SELECT
Selects signal detection for similar 1080I signal manually.
1080I : Standard digital broadcasts
540P : Special digital broadcasts ( ex. DTC100 )
1080I
NO
RGB SELECT
If there is a problem with signal detection, this function forces the
monitor to display the signal at the desired resolution.
If no problem is detected, the only available option will be “AUTO”.
VGA input only.
AUTO
YES
HDMI MODE
Choose the HDMI mode based on the input device connected via
HDMI connector.
When a DVD player or similar equipment is connected, sets to
"HIGH".
When a PC or similar equipment is connected, sets to "LOW".
HIGH
NO
Choose the DVI mode based on the input device connected via
DVI connector and set the black level.
When a PC or similar equipment is connected, PLUG/PLAY is
"DVI-PC" and BLACK LEVEL is "LOW".
When a DVD player or similar equipment is connected, PLUG/
PLAY is "DVI-HD" and BLACK LEVEL is "HIGH".
DVI-PC
NO
LOW
NO
The selected Color System depends on the video format of the
input signal.
VIDEO input only.
AUTO
NO
DVI MODE
PLUG/PLAY
BLACK LEVEL
COLOR SYSTEM
English-16
Downloaded From TV-Manual.com Manuals
Main Menu
Sub Menu
SET UP
(continued)
BACK GROUND
Chooses the brightness of background when there is no input
signal present.
SIDE MASK
Adjusts the color of the side mask when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
OSD
FUNCTION
Some functions
available only
when the
Advanced OSD
function in the
FUNCTION
menu is
enabled.
Sub Menu2
Explanation
DISPLAY OSD
ON: Information about inputs, screen size, etc. is shown.
OFF: No information is shown.
OSD
POSITION
Change the position of the menu between TOP LEFT and BTM
RIGHT. Press + or - to adjust.
OSD ORBITER
ON: The menu position intermittently shifts eight dots while the
OSD is being displayed.
OFF: The menu position does not shift.
OSD TRANSP.
Adjusts the transparency level of the OSD.
Press + or - to adjust.
Default
Reset
GRAY
YES
3
YES
ON
YES
TOP LEFT
YES
ON
YES
70%
YES
MONITOR ID
Sets the monitor ID number from 1-26 or to "ALL".
ALL
YES
ALL RESET
Resets settings back to factory default values.
OFF
-
ADVANCED OSD
ON: All menu items are shown for advanced users.
OFF: Some of the advanced menu items are not shown.
OFF
YES
POWER SAVE
Sets how long the monitor waits to go into power save mode after
a signal is lost.
VGA and DVI input and Separate HV sync. only.
OFF
YES
INPUT SKIP
Skips to next input if present input is no signal.
This function is valid only for INPUT key on the display.
OFF
YES
AUTO
YES
NORMAL
YES
100%
YES
SUB PICTURE
The
ADVANCED
OSD function
is always
available.
SUB
P.DETECT
DISPLAY
This function automatically detects no input signal of sub screen.
This feature is available only picture-in-picture mode.
SUB P. DETECT: Sets availability of automatic detecting of sub
screen.
DISPLAY: Sets the appearance method of the sub screen.
SUB P. RATE: Sets the transparency of the sub screen.
SUB P.RATE
ZOOM NAV
Sets the position of the zoom navigation image.
BTM LFT
YES
PICTURE FREEZE
Sets the position of the captured still picture.
S BY S1
YES
SCREEN SAVER
Use the SCREEN SAVER function to reduce the risk of Image
Persistence.
PEAK BRIGHT : The brightness is decreased depending on
setting.
ORBITER : The screen image moves slightly with squeezing or
expanding.
INVERSE : The screen image is displayed alternately between
positive image and negative image, or the screen image is
displayed full white.
MANUAL
YES
100%
YES
AUTO1
YES
OFF
YES
OFF
YES
NORMAL
YES
Sets the input mode and the sound volume when the power turn
on.
LAST : last mode (the input that was last selected when the power
turn off.)
MULTI to DVI : fixed input mode.
AUTO : Searches the input with the signal automatically
PRIORITY : Sets the priority input for AUTO setting.
LAST
YES
LAST
YES
PROTOCOL SET
Sets protocol setting of RS-232C.
OFF : When NEC protocol is used (normal).
ON : When special protocol is used.
* Consult your dealer for details of protocol.
OFF
YES
RS232C CONTROL
Selects the mode of the monitor when using the RS-232C daisy
chain.
NORMAL
YES
Display signal information such as frequencies, polarities, etc.
-
-
PEAK BRIGHT
ORBITER
INVERSE/
WHITE
CLOSED CAPTION
(U.S. models only)
Chooses the closed caption setting.
CAPTION CONT
(U.S. models only)
Chooses the brightness of the closed caption.
INPUT DETECT
INPUT
VOLUME
SIGNAL INFORMATION
English-17
Downloaded From TV-Manual.com Manuals
English
On-Screen Display (OSD)
Operation
2.35:1
Image is expanded at a 2.35:1 ratio to fill the entire screen.
The screen is filled vertically; however, some information
will be lost on the left and right sides of the image.
Picture Size Using Video Signals
Select one of seven picture sizes manually.
While viewing videos or digital video discs, perform the
following actions:
Available for the following inputs:
Video, Component, or RGB input (480I, 480P, 576I, 576P,
720P, 1080I, 1080P)
1. Press the SIZE button on the remote control.
2. To switch the screen sizes, press the SIZE button again
within 3 seconds. The available sizes are NORMAL, FULL,
DYNAMIC, ZOOM, 2.35:1, 14:9, and UNDERSCAN.
If a 720p, 1080i, or 1080p signal is displayed, the available
sizes are FULL, 2.35:1, DYNAMIC, and UNDERSCAN.
To avoid image retention, use the 2.35:1 image size if black
bars are displayed at the top and bottom of the screen
showing the displayed image.
If displaying an enhanced split-screen, the available sizes are
NORMAL and FULL.
NORMAL (4:3)
Images with a 4:3 (Normal) aspect ratio are displayed.
14:9
Image is displayed at a 14:9 aspect ratio.
Available for the following inputs:
Video, Component, or RGB input (480I, 480P, 576I, 576P)
FULL
Horizontally expands anamorphic signals to display the
correct linearity.
Normal (4:3) images are horizontally expanded to fill the
entire screen.
UNDERSCAN
Standard televisions crop (Underscan) images. Utilize the
UNDERSCAN function in the SCREEN menu to display the
entire image.
DYNAMIC
Vertically and horizontally expands the picture but at
different aspect ratios.
NOTE: Depending on the type of component used, black
borders or signal noise may appear near the screen
edges while in UNDERSCAN mode.
Over a period of time, image ghosting, shadowing,
or burn-in may result from continuous display of
underscanned images. While in UNDERSCAN
mode, the brightness may change if a Macrovision
signal is input.
ZOOM
Vertically and horizontally expands the picture while
maintaining the correct aspect ratio.
NOTE: Do not display 4:3 content in NORMAL mode for
extended periods of time to avoid image ghosting,
shadowing, or burn-in.
English-18
Downloaded From TV-Manual.com Manuals
Information:
Supported resolutions: For further information on the
display output of the various VESA signal standards
supported by the unit, see pages 31 - 36.
Picture Size Using Computer
Signals
To expand a 4:3 image to fill the entire screen, switch to the
widescreen mode.
While viewing videos or digital video discs, perform the
following actions:
When 1360 dot x 768 line wide XGA signals with a vertical
frequency of 60 Hz and a horizontal frequency of 47.7 kHz
are input:
1. Press the SIZE button on the remote control.
1. Select an appropriate setting for the RGB SELECT mode.
2. To switch the screen sizes, press the SIZE button again
within 3 seconds. The available sizes are NORMAL, FULL,
and ZOOM.
2. Refer to the Resolutions Supported section of Model
Information on pages 31 - 36.
If an enhanced split-screen is displayed, the available sizes
are NORMAL and FULL.
NOTE: Do not display 4:3 content in NORMAL mode
for extended periods of time to avoid image
shadowing, ghosting, or burn-in.
NORMAL (4:3 or SXGA 5:4)
Images are displayed normally.
FULL
Horizontally expands anamorphic signals to display the
correct linearity.
Normal (4:3) images are horizontally expanded to fill the
entire screen.
ZOOM
Vertically and horizontally expands the picture, while
maintaining the correct aspect ratio.
English-19
Downloaded From TV-Manual.com Manuals
English
Operation - continued
Operation - continued
Press the SWAP button to swap pictures.
Split Screen Mode
To display multiple pictures on the screen, perform the
following actions:
VGA
A
B
1. Press the desired SPLIT SCREEN function button on the
remote (PIP, S BY S, SINGLE).
SWAP
Only certain RGB signals are supported.
VGA
B
A
SINGLE
button
PIP
button
S BY S
button
VGA
A
A
SINGLE
button
PIP
button
Press the SELECT/FREEZE button to change the active
picture.
VGA
A
B
VGA
B
VIDEO1 is active.
S BY S
button
A
B
Split Screen mode works according to the table below.
SELECT/FREEZE
Side by Side Mode
Press the -, +, p or q buttons to change the picture size.
VIDEO1
VGA
A
VGA
+
button
+
button
VGA is active.
B
VGA
VGA
A
B
Side by Side2-R
q
button
A
button
p
button
VGA
A
B
Side by Side1
q
button
button
p
button
+
button
B
Side by Side2-L
q
button
+
button
p
button
VGA
VGA
A
B
Side by Side4-R
A
button
A
B
Side by Side3
button
B
Side by Side4-L
PIP normal operation test
PIP
available
Main
source
Sub source
VIDEO1
S-VIDEO
DVD/HD1
DVD/HD2
DVD/HD3
SCART1
SCART2
VGA
DVI
VIDEO1
--
YES
YES
YES
YES
--
--
YES
YES
S-VIDEO
YES
--
YES
YES
YES
--
--
YES
YES
DVD/HD1
YES
YES
--
YES
YES
--
--
YES
YES
DVD/HD2
YES
YES
YES
--
YES
--
--
YES
YES
DVD/HD3
YES
YES
YES
YES
--
YES
YES
YES
--
SCART1
--
--
--
--
YES
--
--
--
YES
SCART2
--
--
--
--
YES
--
--
--
YES
VGA
YES
YES
YES
YES
YES
--
--
--
YES
DVI
YES
YES
YES
YES
--
YES
YES
YES
--
English-20
Downloaded From TV-Manual.com Manuals
Picture-in-Picture Mode
Displaying Input Signal
Press the + and - buttons to change the position of the subpicture.
1. To make the desired picture active, press the SELECT/
FREEZE button.
+
button
VGA
B
2. To change the active signal, press the VIDEO, DVD/HD,
or RGB button.
VGA
A
B
A
The input selection may also be changed by pressing the
INPUT button on the front of the unit.
button
button
+
button
button
VGA
B
+
button
button
Adjusting the OSD controls
VGA
A
A
1. To make the desired picture active, press the SELECT/
FREEZE button.
B
+
button
2. To display the main menu, press the MENU button.
Press the p and q buttons to change the size of the subpicture.
3. Adjust the settings as desired.
VGA
A
NOTE: Some OSD functions may not be available in SplitScreen mode.
button
B
VGA
A
button
button
B
VGA
button
B
A
button
VGA
button
A
B
Press the SELECT/FREEZE button to change the active
picture.
VGA
B
A
VIDEO1
B
VGA
A
English-21
Downloaded From TV-Manual.com Manuals
English
Operation - continued
Operation - continued
Picture Settings Menu
Storing picture settings
This function stores the current input signal and PICTURE
menu settings in memory in order to recall these settings if
necessary. Up to six different settings can be stored.
Notes of up to 15 characters long can also be stored along
with each setting.
Example: Storing picture settings at MEMORY1
On the “PICTURE MEMORY” function under the
“PICTURE” menu, select “MEMORY1” and press the SET
button. The “PICTURE MEMORY” screen appears.
PICTURE MEMORY
OFF: Picture memory not used.
MEMORY1 TO 6: Choose the desired memory slot to set.
There are 6 to choose from, independent of inputs.
SETTING THE MEMORY
Use the p and q buttons to select the desired memory slot,
from MEMORY1 to MEMORY6.
Use the t and u buttons to select “SET”, then press the SET
button.
If necessary, input a note.
RESETTING THE MEMORY
Use the p and q buttons to select the desired memory slot,
from MEMORY1 to MEMORY6, then use the t and u
buttons to select “RESET”, and press the SET button.
The memory is cleared, and “—” is displayed in the “INPUT”,
“SIGNAL” and “NOTE” columns.
INPUTTING NOTES
Use the t and u buttons to select “NOTE”, then press the
SET button.
Use the p and q button to select the character.
Use the t and u buttons to move the cursor.
Use the SET button to delete the character at the cursor
position.
When you have finished inputting the note, press the EXIT
button.
English-22
Downloaded From TV-Manual.com Manuals
RS-232C
This Plasma monitor can be controlled via personal
computer using an RS-232C connection.
• Powering ON or OFF
• Switching input signals
MONITOR ID and RS-232C CONTROL
NOTE: If your PC (IBM or IBM compatible) is equipped
only with a 25-pin serial port connector, a 25-pin
serial port adapter is required. Contact your dealer
for details.
Up to 26 individual monitors can be controlled through a
daisy chain via RS-232C connection.
1. Connect PC to the monitor.
NOTE: In order to function, the RS-232C OUT terminal
can only be connected to another monitor of the
same model. Do not connect to other types of
equipment.
Connect a PC’s RS-232C control output to the monitor's
RS-232C input. You can then connect the
RS-232C output from this monitor to another monitor’s
RS-232C input. Up to 26 monitors can be connected
using RS-232C.
2. Set Monitor ID and RS-232C Control mode.
For proper operation, the Monitor ID should be
set in the OSD menu of each monitor that is in the
chain. The Monitor ID can be set under the “SETUP”
menu in the OSD. The Monitor ID number can be set
within a range from 1 to 26 or set to "ALL". No two
monitors should share the same Monitor ID number.
It is recommended to number each monitor in a daisy
chain sequentially from 1. The first monitor in the daisy
chain is designated as the primary monitor. Subsequent
monitors with the chain are secondary monitors.
In the “FUNCTION” menu on the first monitor in the
RS-232C daisy chain set the "RS232C CONTROL"
to "NORMAL". Set the "RS232C CONTROL" to
“SECONDARY” on all other monitors.
This monitor uses RXD, TXD and GND
lines for RS-232C control.
The reverse type cable (null modem cable)
should be used for RS-232C control.
OUT
IN
RS-232C (IN)
PC
(Out)
RS-232C (OUT)
RS-232C Cable
RS-232C (IN)
RS-232C Cable
English-23
Downloaded From TV-Manual.com Manuals
OUT
IN
RS-232C (OUT)
English
Functions that can be controlled via RS-232C:
RS-232C - continued
The following control sequence is used for a single monitor
When using the following control commands, all of the daisy-chained monitors
can be controlled at the same time from the primary monitor. However, reply and
status commands will only pertain to the primary monitor, and not to the secondary
monitors.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
2) Control command diagram
The command is structured by the address code, function code, data code and end
code. The length of the command is different for each function.
Address Code
Function Code
Data Code
End Code
HEX
30h 30h
Function
Data
0Dh
ASCII
'0' '0'
Function
Data
[Address code]
30h 30h (In ASCII code, '0' '0') fixed.
[Function code] A code of each fixed control move.
[Data code]
A code of each fixed control data (number) and
not always indicated.
[End code]
0Dh (In ASCII code, '
To control multiple monitors that are daisychained together please use the extended control
command.
English-24
Downloaded From TV-Manual.com Manuals
' ) fixed.
RS-232C - continued
1) The command from a computer to the Plasma monitor will take 400ms.
2) The Plasma monitor will send a return command 400ms* after it has received
an encode. If the command is not received correctly,
the Plasma monitor will not send the return command.
3) The personal computer checks the command and confirms if the
command which has been sent has been executed or not.
4) This Plasma monitor sends various codes other than the return code. When
sending a control sequence via RS-232C, other codes from personal
computers will be ignored.
*The sending time of the return command may be delayed depending on the
monitor’s current activity (changing of the input signal, etc.).
[Example] Turn the power ON. (' ' is for ASCII code)
Sending commands
from the PC etc.
Status code from
Plasma monitor
Meaning
Command for
POWER ON
30 30 21 0D
'0' '0' '!' ' '
30 30 21 0D
'0' '0' '!' ' '
Command received
(Command echo back)
4) Operation commands
Operation commands execute the basic operation setting of this Plasma
monitor. It may not operate when changing the signal:
Operation
ASCII
HEX
POWER ON
!
21h
POWER OFF
"
22h
INPUT VIDEO1
_v1
5Fh 76h 31h
INPUT S-VIDEO
_v3
5Fh 76h 33h
INPUT DVD/HD1
_v2
5Fh 76h 32h
INPUT DVD/HD2
_v5
5Fh 76h 35h
INPUT DVD/HD3
_h1
5Fh 68h 31h
INPUT SCART2
_v6
5Fh 76h 36h
INPUT VGA
_r2
5Fh 72h 32h
INPUT DVI
_r1
5Fh 72h 31h
• POWER OFF command should not be used less than 1 minute after the power is
turned on.
• POWER ON command should not be used less than 1 minute after the power is
turned off.
English-25
Downloaded From TV-Manual.com Manuals
English
3) Control sequence
RS-232C - continued
5) Read command
Host computer sends the command without Data-code to monitor.
After receiving this command, the monitor returns the command with Data-code
of current status to host computer.
<ex> When the Host computer checks the Power status of monitor, the status of
monitor is powered-on.
Command from
computer
Command from
Monitor
30 30 76 50 0D
‘0’’0’’v’’P’[enter]
Detail of command
Ask about the power
status of monitor.
30 30 76 50 31 0D
‘0’’0’’v’'P'’1’[enter]
Monitor is powered-on.
Structure of the Read-command
ASCII
Function
Data
Function Data
POWER ON
vP
1
76h 50h
31h
POWER OFF
vP
0
76h 50h
30h
INPUT VIDEO1
vI
v1
76h 49h
76h 31h
INPUT S-VIDEO
vI
v3
76h 49h
76h 33h
INPUT DVD/HD1
vI
v2
76h 49h
76h 32h
INPUT DVD/HD2
vI
v5
76h 49h
76h 35h
INPUT DVD/HD3
vI
h1
76h 49h
68h 31h
INPUT SCART2
vI
v6
76h 49h
76h 36h
INPUT VGA
vI
r2
76h 49h
72h 32h
INPUT DVI
vI
r1
76h 49h
72h 31h
Picture Mode BRIGHT
vM
p1
76h 4Dh
70h 31h
Picture Mode STANDARD
vM
p2
76h 4Dh
70h 32h
Picture Mode CINEMA1
vM
p3
76h 4Dh
70h 33h
Picture Mode CINEMA2
vM
p4
76h 4Dh
70h 34h
Picture Mode DEFAULT
vM
p5
76h 4Dh
70h 35h
English-26
Downloaded From TV-Manual.com Manuals
HEX
Troubleshooting
Display image is not sized properly
• Use the OSD screen controls to increase or decrease the clock
total.
• Check to make sure that a supported mode has been selected
on the display card or system being used. (Please consult
display card or system manual to change graphics mode.)
• The signal cable should be properly connected to the display
card/computer.
• The display card should be properly seated in its slot.
• Front Power Switch and computer power switch should be in
the ON position.
• Check to make sure that a supported mode has been selected
on the display card or system being used. (Please consult
display card or system manual to change graphics mode.)
• Check the monitor and your display card with respect to
compatibility and recommended settings.
• Check the signal cable connector for bent or pushed-in pins.
Selected resolution is not displayed properly
• Use OSD information to enter Information menu and confirm
that the appropriate resolution has been selected. If not, select
appropriate resolution.
No Sound
• Check to see if speaker cable is properly connected.
• Check to see if mute is activated.
• Check to see if volume is set at minimum.
NOTE: It is possible to play audio from a source that is different
from the video source.
Power Button does not respond
• Unplug the power cord of the monitor from the AC outlet to
turn off and reset the monitor.
Image persistence
• Please be aware that Plasma Technology may experience a
phenomena known as Image Persistence. Image Persistence
occurs when a residual or “ghost” image of a previous image
remains visible on the screen. Unlike CRT monitors, Plasma
monitors’ image persistence is not permanent, but constant
images being displayed for a long period of time should be
avoided. To alleviate image persistence, turn off the monitor
for as long as the previous image was displayed. For example,
if an image was on the monitor for one hour and a residual
image remains, the monitor should be turned off for one hour
to erase the image.
RS-232C does not work
• Check the PROTOCOL SET in the FUNCTION menu.
Remote Control does not work
• Make sure the batteries are inserted properly.
• Test the batteries for strength/life.
• Make sure to point the remote directly at the sensor on the
monitor.
• Check if the remote is in Remote ID mode.
• The remote control may not function when in direct sunlight
or when there is strong illumination on the remote sensor of
the monitor.
NOTE: As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving images and
using a moving screen saver at regular intervals whenever the
screen is idle or turning off the monitor when not in use.
Image is unstable, unfocused or
swimming is apparent
• Signal cable should be properly attached to the Plasma
monitor, computer, or other input device.
• Use the OSD screen controls to focus and adjust display by
increasing or decreasing the clock phase total. When the
display mode is changed, the OSD Image Adjust settings may
need to be readjusted.
• Check the monitor and your display card with respect to
compatibility and recommended signal timings.
Image of component signal is greenish
• Check to see if the DVD/HD input connector is selected.
LED on monitor is not lit
(no green or red color can be seen)
• Main Power Switch should be in the ON position and power
cord should be connected.
Red LED on monitor is blinking
• A certain failure might have occurred, please contact your
nearest authorized NEC DISPLAY SOLUTIONS service
facility.
English-27
Downloaded From TV-Manual.com Manuals
English
No picture
Specifications 42XC10
PDP Module
Frequency
Diagonal: 42 "/1058 mm
Pixel Pitch
0.900 mm (W)/0.676 mm (H)
Resolution
1024 x 768
Horizontal
ANALOG: 15.625/15.734kHz, 31.0kHz - 108.5kHz
Vertical
24Hz to 120.4Hz
DIGITAL: 15.625/15.734kHz, 31.0kHz - 91.1kHz
Panel Display Size
922 mm (W) x 519 mm (H)
36.3 in (W) x 20.4 in (H)
Input Signals
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*, 1920X1080*
VGA
15pin Mini D-sub
Analog RGB
0.7V p-p, Input Impedance 75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3Vp-p Neg
DVD/HD1,2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7Vp-p/75 ohm
HDTV/DVD:1080p*, 1080i*, [email protected]/60Hz,
[email protected], [email protected], [email protected], [email protected]
DVD/HD3
(HDMI)
HDMI Type-A
VIDEO1
RCA
Digital
Component
Composite
HDMI
1080p*,1080i*,[email protected] 50Hz/60Hz, [email protected] 50Hz, [email protected] 60Hz, [email protected],
[email protected]
1.0V p-p Input Impedance 75 ohm
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
S-VIDEO
mini DIN 4 pin
S-VIDEO
Y: 1.0Vp-p/75ohm C: 0.286Vp-p/75 ohm(NTSC),
0.3Vp-p/75ohm(PAL/SECAM)
AUDIO Input
RCA (L/R) X3
Analog Audio
Stereo L/R 0.5Vrms
HDMI Type-A
DIGITAL Audio
PCM 32, 44.1, 48Khz (16bit)
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
Audio
Speaker Output
External Speaker Jack 8W + 8W (8 ohm)
External Control
RS-232C: IN
9 Pin D-sub
RS-232C: OUT
9 Pin D-sub (daisy chain)
Power Supply
[email protected] AC, 50/60Hz
Operational Environment
Temperature
0˚ to 40˚C / 32˚ F to 104˚ F
Humidity
20% to 80% (without condensation)
Temperature
-10˚C to 50˚C / 14˚ F to 122˚ F
Humidity
10 - 90% (without condensation) / 90% - 2% x (Temp - 40°C) regarding over 40°C
Storage Environment
Dimensions (WxHxD)
Net
1036mm(W) x 649mm(H) x 130mm(D) / 40.8"(W) x 25.6"(H) x 5.1"(D)
Gross
1220mm(W) x 900mm(H) x 360mm(D) / 48.0"(W) x 35.4"(H) x 14.2"(D)
Weight
(without speaker and stand )
Net
34.5 kg / 76.1 lbs
Gross
42.5 kg / 93.7 lbs
VESA compatible arm
mounting interface
700mm x 300mm
4 Holes (screw M8 Depth 16mm)
Complied Regulatory
and Guidelines
UL 60065/CSA C22.2 No.60065/EN60065/IEC60065
FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/C-Tick
Power Management
VESA DPM (Separate HV Sync. only)
Plug & Play
VESA DDC2B
Accessories
Remote control, AA Batteries, Power cord, Users Manual (CD-ROM),
Start Up Guide (Paper / CD-ROM), Main Power Switch cover and screw, Cable clamps
*Compressed Image
English-28
Downloaded From TV-Manual.com Manuals
Specifications 50XC10
Frequency
Diagonal: 50"/1269 mm
Pixel Pitch
0.81 mm (W)/0.81 mm (H)
Resolution
1365 x 768
Horizontal
ANALOG: 15.625/15.734kHz, 31.0kHz - 108.5kHz
Vertical
24Hz to 120.4Hz
DIGITAL: 15.625/15.734kHz, 31.0kHz - 91.1kHz
Panel Display Size
1106 mm (W) x 622 mm (H)
43.5 in (W) x 24.5 in (H)
Input Signals
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*, 1920X1080*
VGA
15pin Mini D-sub
Analog RGB
0.7V p-p, Input Impedance 75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3Vp-p Neg
DVD/HD1,2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7Vp-p/75 ohm
HDTV/DVD:1080p*, 1080i*, [email protected]/60Hz,
[email protected], [email protected], [email protected], [email protected]
DVD/HD3
(HDMI)
HDMI Type-A
VIDEO1
RCA
Digital
Component
Composite
HDMI
1080p*,1080i*,[email protected] 50Hz/60Hz, [email protected] 50Hz, [email protected] 60Hz, [email protected],
[email protected]
1.0V p-p Input Impedance 75 ohm
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
S-VIDEO
mini DIN 4 pin
S-VIDEO
Y: 1.0Vp-p/75ohm C: 0.286Vp-p/75 ohm(NTSC),
0.3Vp-p/75ohm(PAL/SECAM)
AUDIO Input
RCA (L/R) X3
Analog Audio
Stereo L/R 0.5Vrms
HDMI Type-A
DIGITAL Audio
PCM 32, 44.1, 48Khz (16bit)
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
Audio
Speaker Output
External Speaker Jack 8W + 8W (8 ohm)
External Control
RS-232C: IN
9 Pin D-sub
RS-232C: OUT
9 Pin D-sub (daisy chain)
Power Supply
[email protected] AC, 50/60Hz
Operational Environment
Temperature
0˚ to 40˚C / 32˚ F to 104˚ F
Humidity
20% to 80% (without condensation)
Temperature
-10˚C to 50˚C / 14˚ F to 122˚ F
Humidity
10 - 90% (without condensation)/ 90% - 2% x (Temp - 40°C) regarding over 40°C
Net
1221mm(W) x 748mm(H) x 130mm(D) / 48.1"(W) x 29.4"(H) x 5.1"(D)
Storage Environment
Dimensions (WxHxD)
Gross
1400mm(W) x 980mm(H) x 360mm(D) / 55.1"(W) x 38.6"(H) x 14.2"(D)
Weight
(without speaker and stand )
Net
49.0 kg / 108.0 lbs
Gross
59.0 kg / 130.1 lbs
VESA compatible arm
mounting interface
700mm x 300mm
4 Holes (screw M8 Depth 16mm)
Complied Regulatory
and Guidelines
UL 60065/CSA C22.2 No.60065/EN60065/IEC60065
FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/C-Tick
Power Management
VESA DPM (Separate HV Sync. only)
Plug & Play
VESA DDC2B
Accessories
Remote control, AA Batteries, Power cord, Users Manual (CD-ROM),
Start Up Guide (Paper / CD-ROM), Main Power Switch cover and screw, Cable clamps
*Compressed Image
English-29
Downloaded From TV-Manual.com Manuals
English
PDP Module
Specifications 60XC10
PDP Module
Frequency
Diagonal: 60"/1514 mm
Pixel Pitch
0.966 mm (W)/0.966 mm (H)
Resolution
1366 x 768
Horizontal
ANALOG: 15.625/15.734kHz, 31.0kHz - 108.5kHz
Vertical
24Hz to 120.4Hz
DIGITAL: 15.625/15.734kHz, 31.0kHz - 91.1kHz
Panel Display Size
1320 mm (W) x 742 mm (H)
51.9 in (W) x 29.2 in (H)
Input Signals
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*, 1920X1080*
VGA
15pin Mini D-sub
Analog RGB
0.7V p-p, Input Impedance 75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3Vp-p Neg
DVD/HD1,2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7Vp-p/75 ohm
HDTV/DVD:1080p*, 1080i*, [email protected]/60Hz,
[email protected], [email protected], [email protected], [email protected]
DVD/HD3
(HDMI)
HDMI Type-A
VIDEO1
RCA
Digital
Component
Composite
HDMI
1080p*,1080i*,[email protected] 50Hz/60Hz, [email protected] 50Hz, [email protected] 60Hz, [email protected],
[email protected]
1.0V p-p Input Impedance 75 ohm
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
S-VIDEO
DIN 4 pin
S-VIDEO
Y: 1.0Vp-p/75ohm C: 0.286Vp-p/75 ohm(NTSC),
0.3Vp-p/75ohm(PAL/SECAM)
AUDIO Input
RCA (L/R) X3
Analog Audio
Stereo L/R 0.5Vrms
HDMI Type-A
DIGITAL Audio
PCM 32, 44.1, 48Khz (16bit)
NTSC/PAL(B, G, M, N)/SECAM/4.43NTSC/PAL60
Audio
Speaker Output
External Speaker Jack 8W + 8W (8 ohm)
External Control
RS-232C: IN
9 Pin D-sub
RS-232C: OUT
9 Pin D-sub (daisy chain)
Power Supply
[email protected] AC, 50/60Hz
Operational Environment
Temperature
0˚ to 40˚C / 32˚ F to 104˚ F
Humidity
20% to 80% (without condensation)
Temperature
-10˚C to 50˚C / 14˚ F to 122˚ F
Humidity
10 - 90% (without condensation)/ 90% - 2% x (Temp - 40°C) regarding over 40°C
Storage Environment
Dimensions (WxHxD)
Net
1447mm(W) x 876mm(H) x 130mm(D) / 57.0"(W) x 34.5"(H) x 5.1"(D)
Gross
1620mm(W) x 1100mm(H) x 360mm(D) / 63.8"(W) x 43.3"(H) x 14.2"(D)
Weight
(without speaker and stand )
Net
70.0 kg / 154.3 lbs
Gross
83.0 kg / 183.0 lbs
VESA compatible arm
mounting interface
700mm x 300mm
4 Holes (screw M8 Depth 16mm)
Complied Regulatory
and Guidelines
UL 60065/CSA C22.2 No.60065/EN60065/IEC60065
FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/C-Tick
Power Management
VESA DPM (Separate HV Sync. only)
Plug & Play
VESA DDC2B
Accessories
Remote control, AA Batteries, Power cord, Users Manual (CD-ROM),
Start Up Guide (Paper / CD-ROM), Main Power Switch cover and screw, Cable clamps
*Compressed Image
English-30
Downloaded From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals
English-31
Wide-UXGA
Wide-UXGA
Mac13"
Mac16"
Mac19"
Mac21"
Apple17
EWS4800
1920 X 1200
1920 X 1200RB
640 X 480
832 X 624
1024 X 768
1152 X 870
1440 X 900
Work Station
1280 X 1024
1280 X 1024
1152 X 900
1152 X 900
1280 X 1024
1024 X 768
1280 X 1024
NORMAL (4:3)
768 pixels x 768 lines
--
1024 pixels x 768 lines
FULL(16:9)
SGI
HP
SUN
Wide-SXGA
UXGA
1680 X 1050
1600 X 1200
1920 X 1080
SXGA+
Wide-XGA
1280 X 768
1400 X 1050
XGA
1152 X 864
Wide-XGA
Wide-XGA
SXGA
XGA
1024 X 768
1360 X 768
1376 X 768
1280 X 1024
Wide-VGA
Wide-VGA
SVGA
848 X 480
852 X 480
800 X 600
Wide-XGA
Wide-XGA
Wide-XGA
350line
VGA
720 X 350
640 X 480
1280 X 800
1280 X 854
1280 X 960
400line
400line
640 X 400
720 X 400
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
81
82
83
84
85
91
92
93
94
95
96
97
98
Not Supported
EWS Series
Apple Macintosh®
IBM PC/AT
Compatible
Computers
HXV
no.
Signal Type
Resolution
Sig.
(*1)
31.5
31.5
37.9
31.5
31.5
37.9
37.5
43.3
51.1
61.3
31
31.7
35.2
37.9
48.1
46.9
53.7
63
75.7
48.4
56.5
57.9
60
68.7
80.5
95.5
53.7
64.9
67.5
45.1
48
47.8
56
57.8
49.7
53.1
60
85.9
47.7
48.3
64
80
91.1
108.5
64
65.3
82.3
93.9
65.3
75
81.3
87.5
93.8
106.3
56.2
67.5
74.6
74
35
49.7
60.2
68.7
55.9
64.6
75.1
78.1
61.8
71.7
81.1
49.7
63.9
(kHz)
Aspect ratio is 5:4 (720x768)
Hz
70.1
70.1
85
70.1
59.9
72.8
75
85
100.4
120.4
60
60
56.3
60.3
72.2
75
85.1
99.8
120
60
70.1
71.9
75
85
100.6
119.4
60
72
75
56.2
59.8
59.9
69.8
72
59.8
60
60
85
60
59.9
60
75
85
100.1
60
60
74.9
85
60
60
65
70
75
85
50
60
59.9
60
66.7
74.6
74.9
75.1
59.9
60
71.2
72
66
76
76.1
60
60
Specification of the signal
H freq.
V freq.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *2
Yes
Yes
Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
Yes
Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
--Yes *2
Yes *2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes *1
Yes *1
Yes *1 *2
Yes *1 *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes *1
Yes *1
Yes *1
Yes
Yes
Yes *1
Yes
Yes *1
(*2)
(16:9)
FULL
(4:3)
NORMAL
Rough Sampling
VGA
terminal
INPUT
S I ZE
Analog
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZO OM
DVI
(DVI-PC)
terminal
INPUT
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes
--Yes *1
Yes *1
Yes *1
-Yes
Yes
Yes
--Yes
-------------Yes *1
Yes *1
Yes *1
Yes
Yes
Yes *1
Yes
Yes *1
(4:3)
NORMAL
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-Yes
Yes
Yes
-Yes
Yes
----Yes
Yes
-Yes
----Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(16:9)
FULL
SIZE
Digital
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes
--Yes
Yes
Yes
-Yes
Yes
Yes
--Yes
-------------Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZOOM
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Pos.
Pos.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Sync on G
Sync on G
Sync on G
Sync on G
Neg.
Neg.
Neg.
C Sync
C Sync
C Sync
-
Neg.
Neg.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Sync on G
Sync on G
Sync on G
Sync on G
Pos.
Neg.
Neg.
C Sync
C Sync
C Sync
-
V
Sync polarity
H
Sync
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
presence
1
1
-1
2
-----2
2
-------3
5
6
--------3
3
5
6
4
---3
3
9
---9
7
--7
8
------8
------------4
--
640X400
720X400
-720X350
640X480
-----848X480
852X480
-------1024X768
1024X768
1024X768
--------1280X768-1
1280X768-2
1280X768
1280X768
1280X800
---1360X768
1376X768
1280X1024
---1400X1050
1400X1050
--1680X1050
1600X1200
------1920X1200
------------1024X768
--
Item
RGB select
Gr. No.
English
42XC10 Supported Resolutions (PC)
Composite / S
Downloaded From TV-Manual.com Manuals
English-32
NORMAL(4:3)
768 pixels x 768 lines
--
101
102
103
104
105
106
107
SD
111
112
113
114
HD
115
116
117
118
119
120
121
122
123
SD
131
132
133
134
HD
135
136
137
138
139
140
141
142
143
144
161
SD
162
163
164
165
166
HD
167
168
169
170
171
172
173
174
Native 191
Resolution 192
193
(*3)
Hz
59.9
59.9
50
59.9
50
59.9
50
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
60
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
50
30
24
25
60
60
60
15.8
15.8
15.6
15.8
15.6
15.8
15.6
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
33.8
31.5 / 31.5
15.7 / 15.8
31.5 / 31.5
15.6
31.3
45.0 / 45.0
33.7 / 33.8
67.4 / 67.5
37.5
28.1
56.3
33.8
27
28
47.3
47.3
30
(kHz)
Displayed by Underscan mode (100%)
RCA STB
Signal Type
1024 pixels x 768 lines
FULL(16:9)
3.58NTSC
4.43NTSC
PAL
PAL60
PAL-N
PAL-M
SECAM
480I
576I
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
480I *4
576I *4
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
1080A/540P
640 X 480P
720 (1440) X 480I
720 X 480P
720 (1440) X 576I
720 X 576P
1280 X 720P
1920 X 1080I
1920 X 1080P
1280 X 720P
1920 X 1080I
1920 X 1080P
1920 X 1080P
1920 X 1080P
1920 X 1080P
1366 X 768
1024 X 768
853 X 480
HXV
no.
Not Supported
Digital
(EIA/CEA-861)
RGB(Video signal)
Y,Pb(Cb),Pr(Cr)
Video
Resolution
Sig.
Specification of the signal
H freq.
V freq.
SCART input available
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
(4:3)
NORMAL
(*4)
VGA
(SCART1-2)
DVD/HD1
DVD/HD2
Video1
S-Video
terminal
I N PU T
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(16:9)
FULL
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(non-linear)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
SIZE
DYNAMIC ZOOM
Analog
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
14:9
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
2.35:1
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
------------------
SCAN
UNDER
DVD/HD3
(HDMI)
DVI
(DVI-HD)
terminal
INPUT
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
(4:3)
NORMAL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *3
Yes *3
Yes *3
(16:9)
FULL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
(non-linear)
DYNAMIC
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
SIZE
ZOOM
Digital
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
14:9
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
2.35:1
----------------------------------Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
----
SCAN
UNDER
----------------------2
-----------------------------
----------------------480P
-----------------------------
Item
RGB select
Gr. No.
---------------------------1080I
-----5 40 P
------------------
Item
HD select
42XC10 Supported Resolutions (Video)
Downloaded From TV-Manual.com Manuals
English-33
NORMAL (4:3)
1024 pixels x 768 lines
--
FULL (16:9)
1365 pixels x 768 lines
1920 X 1200
1920 X 1200RB
640 X 480
832 X 624
1024 X 768
1152 X 870
1440 X 900
Work Station
1280 X 1024
1280 X 1024
1152 X 900
1152 X 900
1280 X 1024
1024 X 768
1280 X 1024
1920 X 1080
1680 X 1050
1600 X 1200
1400 X 1050
1360 X 768
1376 X 768
1280 X 1024
1280 X 800
1280 X 854
1280 X 960
1280 X 768
1152 X 864
1024 X 768
848 X 480
852 X 480
800 X 600
720 X 350
640 X 480
Resolution
HXV
640 X 400
720 X 400
Not Supported
EWS Series
Apple Macintosh®
IBM PC/AT
Compatible
Computers
Sig.
no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
81
82
83
84
85
91
92
93
94
95
96
97
98
(*2)
NORMAL
(4:3)
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes *1
Yes *1
Yes *1 *2
Yes *1 *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes *1
Yes *1
Yes *1
Yes
Yes
Yes *1
Yes
Yes *1
SIZE
FULL
(16:9)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *2
Yes
Yes
Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
Yes
Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
--Yes *2
Yes *2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Analog
Rough Sampling
INPUT
terminal
VGA
Aspect ratio is 5:4 (960x768)
(*1)
Specification of the signal
V freq.
H freq.
(kHz)
Signal Type
Hz
400line
70.1
31.5
400line
70.1
31.5
85
37.9
350line
70.1
31.5
VGA
59.9
31.5
72.8
37.9
75
37.5
85
43.3
100.4
51.1
120.4
61.3
Wide-VGA
60
31
Wide-VGA
60
31.7
SVGA
56.3
35.2
60.3
37.9
72.2
48.1
75
46.9
85.1
53.7
99.8
63
120
75.7
XGA
60
48.4
70.1
56.5
71.9
57.9
75
60
85
68.7
100.6
80.5
119.4
95.5
XGA
60
53.7
72
64.9
75
67.5
Wide-XGA
56.2
45.1
59.8
48
59.9
47.8
69.8
56
72
57.8
Wide-XGA
59.8
49.7
Wide-XGA
60
53.1
Wide-XGA
60
60
85
85.9
Wide-XGA
60
47.7
Wide-XGA
59.9
48.3
SXGA
60
64
75
80
85
91.1
100.1
108.5
60
64
SXGA+
60
65.3
74.9
82.3
85
93.9
60
65.3
Wide-SXGA
60
75
UXGA
65
81.3
70
87.5
75
93.8
85
106.3
50
56.2
60
67.5
Wide-UXGA
59.9
74.6
Wide-UXGA
60
74
66.7
35
Mac13"
Mac16"
74.6
49.7
Mac19"
74.9
60.2
Mac21"
75.1
68.7
Apple17
59.9
55.9
60
64.6
EWS4800
71.2
75.1
HP
72
78.1
SUN
66
61.8
76
71.7
76.1
81.1
SGI
60
49.7
60
63.9
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZOOM
SIZE
INPUT NORMAL FULL
terminal
(4:3)
(16:9)
--DVI
(DVI-PC)
-Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---Yes
-Yes
-Yes
-Yes
-Yes
-Yes
Yes
Yes
Yes
Yes
-Yes
-Yes
Yes *1
Yes
Yes *1
Yes
Yes *1
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
---Yes
Yes
Yes
---------Yes
-Yes
---Yes
---------Yes
Yes *1
Yes
Yes *1
Yes
Yes *1
Yes
Yes
Yes
Yes
Yes
Yes *1
Yes
Yes
Yes
Yes *1
Yes
Digital
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes
--Yes
Yes
Yes
-Yes
Yes
Yes
--Yes
-------------Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZOOM
Sync polarity
H
V
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Neg.
Pos.
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Neg.
Pos.
Neg.
Neg.
Neg.
Neg.
C Sync
C Sync
C Sync
C Sync
C Sync
C Sync
Sync
presence
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
RGB select
Gr. No.
Item
1
640X400
1
720X400
--1
720X350
2
640X480
----------848X480
2
2
852X480
--------------3
1024X768
5
1024X768
6
1024X768
----------------3
1280X768-1
3
1280X768-2
1280X768
5
6
1280X768
4
1280X800
------3
1360X768
3
1376X768
9
1280X1024
------9
1400X1050
7
1400X1050
----7
1680X1050
8
1600X1200
------------8
1920X1200
------------------------4
1024X768
---
English
50XC10 Supported Resolutions (PC)
Composite / S
Downloaded From TV-Manual.com Manuals
English-34
NORMAL (4:3)
1024 pixels x 768 lines
--
101
102
103
104
105
106
107
111
SD
112
113
114
HD
115
116
117
118
119
120
121
122
123
SD
131
132
133
134
HD
135
136
137
138
139
140
141
142
143
144
SD
161
162
163
164
165
HD
166
167
168
169
170
171
172
173
174
Native 191
Resolution 192
193
1365 pixels x 768 lines
FULL (16:9)
3.58NTSC
4.43NTSC
PAL
PAL60
PAL-N
PAL-M
SECAM
480I
576I
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
480I *4
576I *4
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
1080A/540P
640 X 480P
720 (1440) X 480I
720 X 480P
720 (1440) X 576I
720 X 576P
1280 X 720P
1920 X 1080I
1920 X 1080P
1280 X 720P
1920 X 1080I
1920 X 1080P
1920 X 1080P
1920 X 1080P
1920 X 1080P
1366 X 768
1024 X 768
853 X 480
HXV
no.
Not Supported
Digital
(EIA/CEA-861)
RGB(Video signal)
Y,Pb(Cb),Pr(Cr)
Video
Resolution
Sig.
(*3)
Hz
59.9
59.9
50
59.9
50
59.9
50
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
60
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
50
30
24
25
60
60
60
15.8
15.8
15.6
15.8
15.6
15.8
15.6
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
33.8
31.5 / 31.5
15.7 / 15.8
31.5 / 31.5
15.6
31.3
45.0 / 45.0
33.7 / 33.8
67.4 / 67.5
37.5
28.1
56.3
33.8
27
28
47.3
47.3
30
(kHz)
Displayed by Underscan mode (100%)
RCA STB
Signal Type
Specification of the signal
H freq.
V freq.
SCART input available
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
(4:3)
NORMAL
(*4)
VGA
(SCART1-2)
DVD/HD1
DVD/HD2
Video1
S-Video
terminal
INPUT
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(16:9)
FULL
Analog
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(non-linear)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
SIZE
DYNAMIC ZOOM
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
14:9
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
2.35:1
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
------------------
SCAN
UNDER
DVD/HD3
(HDMI)
DVI
(DVI-HD)
terminal
INPUT
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
(4:3)
NORMAL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *3
Yes *3
Yes *3
(16:9)
FULL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
(non-linear)
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
SIZE
ZOOM
Digital
DYNAMIC
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
14:9
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
2.35:1
----------------------------------Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
----
SCAN
UNDER
----------------------2
-----------------------------
----------------------480P
-----------------------------
Item
RGB select
Gr. No.
---------------------------1080I
-----540P
------------------
Item
HD select
50XC10 Supported Resolutions (Video)
Downloaded From TV-Manual.com Manuals
English-35
Wide-UXGA
Wide-UXGA
Mac13"
Mac16"
Mac19"
Mac21"
Apple17
EWS4800
1920 X 1200
1920 X 1200RB
640 X 480
832 X 624
1024 X 768
1152 X 870
1440 X 900
Work Station
1280 X 1024
1280 X 1024
1152 X 900
1152 X 900
1280 X 1024
1024 X 768
1280 X 1024
NORMAL (4:3)
1024 pixels x 768 lines
--
1366 pixels x 768 lines
FULL (16:9)
SGI
HP
SUN
Wide-SXGA
UXGA
1680 X 1050
1600 X 1200
1920 X 1080
SXGA+
Wide-XGA
1280 X 768
1400 X 1050
XGA
1152 X 864
Wide-XGA
Wide-XGA
SXGA
XGA
1024 X 768
1360 X 768
1376 X 768
1280 X 1024
Wide-VGA
Wide-VGA
SVGA
848 X 480
852 X 480
800 X 600
Wide-XGA
Wide-XGA
Wide-XGA
350line
VGA
720 X 350
640 X 480
1280 X 800
1280 X 854
1280 X 960
Signal Type
400line
400line
Resolution
HXV
640 X 400
720 X 400
Not Supported
EWS Series
Apple Macintosh®
IBM PC/AT
Compatible
Computers
Sig.
no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
81
82
83
84
85
91
92
93
94
95
96
97
98
(*2)
NORMAL
(4:3)
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes *1
Yes *1
Yes *1 *2
Yes *1 *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes *1
Yes *1
Yes *1
Yes
Yes
Yes *1
Yes
Yes *1
SIZE
FULL
(16:9)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *2
Yes
Yes
Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
Yes
Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
--Yes *2
Yes *2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Analog
Rough Sampling
INPUT
terminal
VGA
Aspect ratio is 5:4 (960x768)
(*1)
Specification of the signal
V freq.
H freq.
(kHz)
Hz
70.1
31.5
70.1
31.5
85
37.9
70.1
31.5
59.9
31.5
72.8
37.9
75
37.5
85
43.3
100.4
51.1
120.4
61.3
60
31
60
31.7
56.3
35.2
60.3
37.9
72.2
48.1
46.9
75
85.1
53.7
99.8
63
120
75.7
60
48.4
70.1
56.5
71.9
57.9
75
60
85
68.7
100.6
80.5
95.5
119.4
60
53.7
72
64.9
75
67.5
56.2
45.1
59.8
48
59.9
47.8
69.8
56
72
57.8
59.8
49.7
60
53.1
60
60
85
85.9
60
47.7
59.9
48.3
60
64
75
80
85
91.1
100.1
108.5
60
64
60
65.3
82.3
74.9
85
93.9
60
65.3
60
75
65
81.3
70
87.5
75
93.8
85
106.3
50
56.2
60
67.5
59.9
74.6
60
74
66.7
35
74.6
49.7
74.9
60.2
75.1
68.7
59.9
55.9
60
64.6
71.2
75.1
72
78.1
66
61.8
76
71.7
76.1
81.1
60
49.7
60
63.9
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes *2
--Yes
Yes
Yes *2
Yes *2
Yes
Yes
Yes *2
Yes *2
-Yes *2
Yes *2
Yes *2
Yes *2
Yes *2
----Yes
Yes
Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZOOM
SIZE
INPUT NORMAL FULL
terminal
(4:3)
(16:9)
--DVI
(DVI-PC)
-Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---Yes
-Yes
-Yes
Yes
--Yes
-Yes
Yes
Yes
Yes
Yes
-Yes
-Yes
Yes *1
Yes
Yes
Yes *1
Yes *1
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
---Yes
Yes
Yes
---------Yes
-Yes
---Yes
---------Yes
Yes *1
Yes
Yes *1
Yes
Yes *1
Yes
Yes
Yes
Yes
Yes
Yes *1
Yes
Yes
Yes
Yes *1
Yes
Digital
----Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-------Yes
Yes
--Yes
Yes
Yes
-Yes
Yes
Yes
--Yes
-------------Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ZOOM
Sync polarity
H
V
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Neg.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Pos.
Neg.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Neg.
Pos.
Pos.
Neg.
Neg.
Pos.
Neg.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
Neg.
Pos.
Neg.
Pos.
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Sync on G Sync on G
Neg.
Pos.
Neg.
Neg.
Neg.
Neg.
C Sync
C Sync
C Sync
C Sync
C Sync
C Sync
Sync
presence
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
RGB select
Gr. No.
Item
1
640X400
1
720X400
--1
720X350
2
640X480
----------2
848X480
2
852X480
--------------3
1024X768
5
1024X768
6
1024X768
----------------1280X768-1
3
3
1280X768-2
5
1280X768
6
1280X768
4
1280X800
------3
1360X768
3
1376X768
9
1280X1024
------9
1400X1050
7
1400X1050
----7
1680X1050
8
1600X1200
------------8
1920X1200
------------------------4
1024X768
---
English
Supported Resolutions (PC) 60XC10
Composite / S
Downloaded From TV-Manual.com Manuals
English-36
no.
NORMAL (4:3)
1024 pixels x 768 lines
--
101
102
103
104
105
106
107
SD
111
112
113
114
115
HD
116
117
118
119
120
121
122
123
SD
131
132
133
134
135
HD
136
137
138
139
140
141
142
143
144
SD
161
162
163
164
165
166
HD
167
168
169
170
171
172
173
174
Native 191
Resolution 192
193
Not Supported
Digital
(EIA/CEA-861)
RGB(Video signal)
Y,Pb(Cb),Pr(Cr)
Video
Sig.
(*3)
Hz
59.9
59.9
50
59.9
50
59.9
50
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
59.9
50
59.9
50
50
60
50
60
50
60
30
24
25
60
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
59.9 / 60.0
59.9 / 60.0
59.9 / 60.0
50
50
50
30
24
25
60
60
60
15.8
15.8
15.6
15.8
15.6
15.8
15.6
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
15.8
15.6
31.5
31.3
37.5
45
28.1
33.8
56.3
67.5
33.8
27
28
33.8
31.5 / 31.5
15.7 / 15.8
31.5 / 31.5
15.6
31.3
45.0 / 45.0
33.7 / 33.8
67.4 / 67.5
37.5
28.1
56.3
33.8
27
28
47.3
47.3
30
(kHz)
Displayed by Underscan mode (100%)
RCA STB
Signal Type
1366 pixels x 768 lines
FULL (16:9)
3.58NTSC
4.43NTSC
PAL
PAL60
PAL-N
PAL-M
SECAM
480I
576I
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
480I *4
576I *4
480P
576P
720P
720P
1080I
1080I
1080P
1080P
1080P
1080P
1080P
1080A/540P
640 X 480P
720 (1440) X 480I
720 X 480P
720 (1440) X 576I
720 X 576P
1280 X 720P
1920 X 1080I
1920 X 1080P
1280 X 720P
1920 X 1080I
1920 X 1080P
1920 X 1080P
1920 X 1080P
1920 X 1080P
1366 X 768
1024 X 768
853 X 480
HXV
Resolution
Specification of the signal
H freq.
V freq.
SCART input available
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
(4:3)
NORMAL
(*4)
VGA
(SCART1-2)
DVD/HD1
DVD/HD2
Video1
S-Video
terminal
INPUT
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(16:9)
FULL
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
(non-linear)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
SIZE
DYNAMIC ZOOM
Analog
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
---------Yes
Yes
Yes
Yes
----------------------------
14:9
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
------------------
2.35:1
DVD/HD3
(HDMI)
DVI
(DVI-HD)
terminal
SCAN
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
------------------
INPUT
UNDER
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
(4:3)
NORMAL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *3
Yes *3
Yes *3
(16:9)
FULL
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
(non-linear)
DYNAMIC
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
SIZE
ZOOM
Digital
----------------------------------Yes *3
Yes
Yes
Yes
Yes
-------------
14:9
----------------------------------Yes *3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
----
2.35:1
----------------------------------Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
Yes *3
----
SCAN
UNDER
----------------------2
-----------------------------
----------------------480P
-----------------------------
Item
RGB select
Gr. No.
---------------------------1080I
-----540P
------------------
Item
HD select
60XC10 Supported Resolutions (Video)
Pin Assignment
1) Analog RGB Input (Mini D-SUB 15P) VGA
English
3) RS-232C Input
(D-SUB 9P)
Pin No. Name
1 Video Signal Red
Pin No. Name
2 Video Signal Green
3 Video Signal Blue
1 Connected to 7 & 8
1
5
4 GND
10
5 DDC-GND
6
2 RXD
11
3 TXD
15
6 Red-GND
4 Connected to 6
5 GND
7 Green-GND
6 Connected to 4
8 Blue-GND
Mini D-SUB 15P
9 +5V (DDC)
7 Connected to 1 & 8
10 SYNC-GND
8 Connected to 1 & 7
11 GND
9 NC
12 DDC-SDA
5
1
13 H-SYNC
14 V-SYNC
9
6
15 DDC-SCL
D-SUB 9P
2) Digital RGB Input (DVI-D) DVI
1 TX2-
9 TX1-
17 TX0-
2 TX2+
10 TX1+
18 TX0+
3 Shield (TX2/TX4)
11 Shield (TX1/TX3)
19 Shield (TXP/TX5)
4 NC
12 NC
20 NC
5 NC
13 NC
21 NC
6 DDC-Serial Clock
14 +5 power
22 Shield (TXC)
7 DDC-Serial Data
15 Ground (+5V)
23 TXC+
8 NC
16 Hot Plug Detect
24 TXC-
8
1
9
16
17
DVI-D
24
English-37
Downloaded From TV-Manual.com Manuals
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products
carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and
electrical accessories, such as signal cables or power cords. When you need to dispose of your NEC display products,
please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable,
follow any agreements made between yourself and NEC. The mark on electrical and electronic products only applies
to the current European Union Member States.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your
local authority so as to comply with the correct disposal method.
Declaration of the Manufacturer
We hereby certify that the color monitor
P426Y3, P506Y4 or P606Y5 is in compliance
with Council Directive 73/23/EEC:
– EN 60065
and marked with
Council Directive 89/336/EEC:
— EN 55022
— EN 61000-3-2
— EN 61000-3-3
— EN 55024
NEC Display Solutions Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
Type of Product:
Equipment Classification:
Model:
NEC Display Solutions of America, Inc.
500 Park Blvd. Suite 1100
Itasca, IL 60143
(630)467-3000
Computer Monitor
Class B Peripheral
PlasmaSync 42XC10 (P426Y3)
PlasmaSync 50XC10 (P506Y4)
PlasmaSync 60XC10 (P606Y5)
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.
All other brands and product names are trademarks or registered trademarks of their respective owners.
Downloaded From TV-Manual.com Manuals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement