Detection Systems Abacus-LED-user

Detection Systems Abacus-LED-user
Full set the system
1.
Enter [user code]
2.
Press [yes/part]
Exit tone sounds.
Part set the system
1.
Enter [user code]
2.
Press [yes/part]
3.
Press [yes/part]
Exit tone sounds.
Unset the system
1.
Enter [user code]
Display shows [_ _].
Reset system after alarm condition
1.
Enter [user code]
Display shows[ ?].
2.
Press [yes/part]
Before the system has time to set.
3.
Enter [user code]
Display shows [_ _], system now reset.
Remote reset after alarm condition
1.
If display shows [AL]
2.
Enter [user code]
Display shows [ ?].
3.
Press [yes/part]
Display shows [En], then a four diget
number.
4.
Quote above four digit number Ask for a "remote or coded reset."
to alarm company
5.
6.
Phone your alarm company and ask for
a coded reset, and give them your
noted down number.
Enter [reply code from alarm
co]
Omit a zone
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [yes/part]
Display shows [O-], select the zone to
be omitted by pressing the
corresponding key.
4.
Press [yes/part]
To confirm selection.
5.
Press [yes/part]
Again to confirm selection, display
shows[O-], ready to accept the next
zone to be omitted.
6.
Press [0/esc]
The zones selected will be omitted next
time the system is set. Display shows
[_ _].
Change your own user code
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [no]
Display shows [bE].
5.
Press [no]
Display shows [Lo].
6.
Press [no]
Display shows [Ch].
7.
Press [no]
Display shows [Co].
8.
Press [yes/part]
Display shows [U-].
9.
Press [1]
Display shows [--].
10.
Enter new [User code]
11.
Press [yes/part]
to confirm the selection. Display shows
[rE].
12.
Enter new [User code]
Again to confirm the selection.
13.
Press [yes/part]
If re-entered correctly a short tone is
generated. Display shows [U-].
14.
Press [0/esc]
Display shows [Co].
15.
Press [0/esc]
Display shows [_ _].
Test the alarm sounders
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [no]
Display shows [bE].
5.
Press [yes/part]
The external devices will now sound
and if fitted the strobe will flash.
6.
Press [0/esc]
Display shows [bE]
7.
Press [0/esc]
Display shows [_ _]
[walked]
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [yes/part]
Display shows[=]To walt test zone,
speaker and keypad will both sound
when zone is passed trough.
5.
Press [yes/part]
to escape walk test.
6.
Press [0/esc]
Display shows [tE]
7.
Press [0/esc]
Display shows [_ _]
Setup user codes
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [no]
Display shows [bE].
5.
Press [no]
Display shows [Lo].
6.
Press [no]
Display shows [Ch].
7.
Press [no]
Display shows [Co].
8.
Press [yes/part]
Display shows [U-].
9.
Press [2]
Display shows [t-], enter the code type
from 1-7
10.
Press [yes/part]
Display shows [--].
11.
Enter new [User code].
12.
Press [yes/part]
Display shows [rE].
13.
Enter new [User code]
Again to confirm the selection.
14.
Press [yes/part]
if re-entered correctly a short tone is
generated. Display shows [U-].
15.
Press [0/esc]
Display shows [Co].
16.
Press [0/esc]
Display shows [_ _].
View the event log
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [no]
Display shows [bE].
5.
Press [no]
Display shows [Lo].
6.
Press [yes/part]
7.
Press [yes/part]
To scroll forward to show more recent
events
8.
Press [0/esc]
Display shows [Lo].
9.
Press [0/esc]
Display shows [_ _]
Set control panel time/clock
1.
Enter [user code]
Display shows [ ?].
2.
Press [no]
Within 20 seconds, display shows [O ].
3.
Press [no]
Display shows [tE].
4.
Press [no]
Display shows [bE].
5.
Press [no]
Display shows [Lo].
6.
Press [no]
Display shows [Ch].
7.
Press [no]
Display shows [Co].
8.
Press [no]
Display shows [CL].
9.
Press [yes/part]
Display shows [d-], Enter date and
month.
10.
Press [yes/part]
to confirm. Display shows [t-]. Enter the
time in 24 hour mode.
11.
Press [yes/part]
to confirm. Display shows [ ?]
12.
Press [0/esc]
Display shows [_ _]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement