RS232 AVR750450380 SH256E 3

RS232 AVR750450380 SH256E 3
Custom Installation Notes:
Serial programming interface and
IR remote commands for
Arcam AVR380/450/750
45
RS232 v2.0 commands............................................ 28
Set/request input name (0x20)..............................................28
FM Scan up/down (0x23).........................................................28
DAB Scan (0x24)...........................................................................28
Heartbeat (0x25)..........................................................................29
AVR380/450/750 RC5 command codes............... 30
Basic Functions.............................................................................30
Advanced Functions..................................................................30
Applicability
The latest version of this document is available on the Arcam Table of
Resources, accessed via http://www.arcam.co.uk/extranethome/tor.
Changelog
Issue 1.0: First public release.
Issue 2.0: USB VFD display data corrected in command 0x09
Issue 3.0: RS232 version number 2.0 to indicate new commands 0x20, 0x23,
0x24, 0x25, 0x26.
Serial Cable Specification
9
DB9 Female
Set/Request Volume (0x0D)....................................................11
Request Mute status (0x0E).....................................................11
Request direct mode status (0x0F)......................................11
Request decode mode status — 2ch (0x10)....................12
Request Decode mode status — MCH (0x11).................12
Request RDS information (0x12)...........................................13
Set/request Video Output Resolution (0x13)...................13
„„ All hexadecimal numbers begin 0x.
„„ Any character in single quotes gives the ASCII equivalent of a hex value.
„„ <n> represents an unknown or variable number.
5
Output Command Specifications......................... 11
Conventions
9
Video selection (0x0A)...............................................................10
Select analogue/digital (0x0B)...............................................10
Set/Request video input type (0x0C)..................................10
The AVR380/450/750 must be correctly configured for Control; by default, Control is disabled for minimum standby power consumption. RS232
control can be enabled using the front panel: press and hold the front panel DIRECT button for 4 seconds until “RS232 CONTROL ON” is displayed
on the VFD. Pressing . Alternatively, Control for RS232 or IP can be enabled using the OSD menu. Press A followed by U on the CR450 remote
control in order to access the setup menu. Use the cursor keys < > , ' and O to enter the General Setup menu and locate the option Control.
Press O, , then O to change this parameter to ‘On’. IP control is via port 50000 of the IP address of the unit (in the Network Settings menu).
6
Input Command Specifications ........................... 10
Treble Equalisaton (0x35).........................................................17
Bass Equalisation (0x36)...........................................................17
Room Equalisation (0x37)........................................................17
Dolby Volume (0x38).................................................................18
Dolby Leveller (0x39).................................................................18
Dolby Volume Calibration Offset (0x3A)............................18
Balance (0x3B)..............................................................................19
Dolby PLII/x Music Dimension (0x3C).................................19
Dolby PLII/x Music Centre Width (0x3D)............................19
Dolby PLII/x Music Panorama (0x3E)...................................20
Subwoofer Trim (0x3F)..............................................................20
Lipsync Delay (0x40)..................................................................20
Compression (0x41)...................................................................21
Request incoming video parameters (0x42)....................21
Request incoming audio format (0x43).............................22
Request incoming audio sample rate (0x44)...................23
Set/Request Sub Stereo Trim (0x45)....................................23
Set/Request Brightness (0x46)...............................................23
Set/Request Contrast (0x47)...................................................24
Set/Request Colour (0x48).......................................................24
Set/Request Film Mode (0x49)...............................................24
Set/Request Edge Enhancement (0x4A)............................25
Set/Request Noise Reduction (0x4C)..................................25
Set/Request MPEG Noise Reduction (0x4D)....................26
Set/Request Zone 1 OSD on/off (0x4E)..............................26
Set/Request Video Output Switching (0x4F)...................26
Set/Request Output Frame Rate (0x50).............................27
Set-up
1
Power (0x00).....................................................................................5
Display Brightness (0x01)............................................................5
Headphones (0x02).......................................................................5
FM genre (0x03) .............................................................................6
Software version (0x04)...............................................................6
Restore factory default settings (0x05).................................6
Save/Restore secure copy of settings (0x06) .....................7
Simulate RC5 IR Command (0x08)..........................................7
Display Information Type (0x09)..............................................8
Request current source (0x1D).................................................9
Headphone Over-ride (0x1F) ....................................................9
Network playback status (0x1C) ..........................................16
Setup Adjustment Command Specifications..... 17
This document describes the remote control protocol for controlling the AVR380/4 5 0/75 0 via the RS232/NET interface. The AVR380/450/750
implements virtual IR commands in order to simplify the protocol. Any operation that can be invoked using the IR remote control can be achieved
over a control link using the Simulate RC5 IR command (0x08). See page 7 for details of this command. The RC5 IR code set is listed from page
30.
6
Example command and response sequence........4
System Command Specifications............................5
Network Command Specifications...................... 16
Introduction
5
Data transfer format......................................................................3
AMX Duet™ Support.....................................................................4
Zone numbers.................................................................................4
Answer codes...................................................................................4
State changes as a result of other inputs.............................4
Reserved Commands...................................................................4
Request menu status (0x14)...................................................14
Request tuner preset (0x15)...................................................14
Tune (0x16)....................................................................................14
Request DAB station (0x18) (AVR450/750 only)............15
Prog. Type/Category (0x19) (AVR450/750 only) ...........15
DLS/PDT info. (0x1A) (AVR450/750 only).........................15
Request preset details (0x1B).................................................16
Controlling the AVR380/450/750 via RS232/NET
1
Introduction.................................................................3
Set-up............................................................................3
Conventions.................................................................3
Command and response formats............................3
Serial Cable Specification..........................................3
Menu Command Specifications............................ 14
DB9 Female
Contents
The cable is wired as a null modem:
Connector 1 pin
2
3
5
Connector 2 pin
3
2
5
Function
Rx  Tx
Tx  Rx
RS232 Ground
Data transfer format
„„ Transfer rate: 38,400bps.
„„ 1 start bit, 8 data bits, 1 stop bit, no parity, no flow control.
Command and response formats
Communication between the remote controller (RC) and the AVR380/450/750 takes the form of sequences of bytes, with all commands and responses
having the same basic format. The AVR380/450/750 shall always respond to a received command, but may also send messages at other times.
Each transmission by the RC is the following format:
<St> <Zn> <Cc> <Dl> <Data> <Et>
„„ St (Start transmission): 0x21 ‘!’
„„ Zn (Zone number): see below.
„„ Cc (Command code): the code for the command
„„ Dl (Data length): the number of data items following this item,excluding the ETR
„„ Data: the parameters for the command
„„ Et (End transmission): 0x0D
Each response by the AVR400 is the following format::
<St> <Zn> <Cc> <Ac> <Dl> <Data> <Et>
„„ St (Start transmission): 0x21 ‘!’
„„ Zn (Zone number): see below.
„„ Cc (Command code): the code for the command
„„ Ac (Answer code): see below.
„„ Dl (Data Length): the number of data items following this item, excluding the ETR
„„ Data: the parameters for the response of length n. n is limited to 255.
„„ Et (End transmission): 0x0D
The AVR380/450/750 responds to each command from the RC within three seconds. The RC may send further commands before a previous command
response has been received.
2
3
Zone numbers
The following zone numbers are defined:
„„ 0x01 – Zone number 1. (Zone 1 is the master zone. Commands that appear zone-less refer to the master zone)
„„ 0x02 – Zone number 2.
System Command Specifications
Power (0x00)
Request the stand-by state of a zone.
Answer codes
The following answer codes are defined:
„„ 0x00 – Status update.
„„ 0x82 – Zone Invalid.
„„ 0x83 – Command not recognised.
„„ 0x84 – Parameter not recognised.
„„ 0x85 – Command invalid at this time.¹
„„ 0x86 – Invalid data length.
¹Certain commands cannot be processed when the Setup Menu is being displayed. An answer code of 0x85 will be returned in these circumstances. Also,
commands for tuner control cannot be processed when the tuner input is not selected, etc.
Example
Command/response sequence to request the power state of zone 1 where
zone 1 has power on:
Command:
0x21 0x01 0x00 0x01 0xF0 0x0D
Response: 0x21 0x01 0x00 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x00
Dl
0x01
Data
0xF0 – Request power state
Et
0x0D
RESPONSE:
State changes as a result of other inputs
It is possible that the state of the AVR380/450/750 may be changed as a result of user input via the front panel buttons or via the IR remote control.
Any change resulting from these inputs is relayed to the RC using the appropriate message type.
For example, if the user changed the front panel display brightness using the DISPLAY button on the front panel, a display message (defined below)
would be sent to the RC. A similar action would be taken for all other state changes (including decode mode changes).
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x00
Ac
Answer code
Dl
0x01
Data
0x00 – Zone is in stand-by
0x01 – Zone is powered on
Et
0x0D
Reserved Commands
Commands 0xF0 to 0xFF (inclusive) are reserved for test functions and should never be used.
Example command and response sequence
As an example, the command to simulate the RC5 command “16-16”, volume up:
STR
0x21
ZONE
0x01
CC
0x08
DL
0x02
Data 1
0x10
Data 2
0x10
Display Brightness (0x01)
Request the brightness of the front panel display.
ETR
0x0D
Assuming that the command was accepted by the AV Receiver and is being processed, the AVR380/450/750 responds to this command with the
following sequence:
STR
0x21
ZONE
0x01
CC
0x08
AC
0x00
DL
0x02
Data 1
0x10
Data 2
0x10
ETR
0x0D
Example
Command/response sequence for requesting the brightness of the display
where the display is off:
Command:
0x21 0x01 0x01 0x01 0xF0 0x0D
Response: 0x21 0x01 0x01 0x00 0x01 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x01
Dl
0x01
Data
0xF0 – Request brightness
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x01
Ac
Answer code
Dl
0x01
Data
0x00 – Front panel is off
0x01 – Front panel L1
0x02 – Front panel L2
Et
0x0D
AMX Duet™ Support
The AVR380/450/750 shall be fully compatible with AMX Duet™ Dynamic Device Discovery Protocol (DDDP) The following description of Dynamic
Device Discovery comes from the AMX website (www.amx.com). Dynamic Device Discovery is part of AMX’s Duet™ platform, which combines the
proven reliability and power of NetLinx with the extensive capabilities of the Java 2 Micro Edition (J2ME) platform. When integrating a serial or IP
device from a manufacturer embedding the Dynamic Device Discovery Protocol (DDDP), Duet recognizes the device and loads the appropriate Duet
module, which automatically installs the new device. AMX’s NetLinx Master can then find and install the Duet device module either from a library
on the master, from AMX’s Web site, or from the manufacturer’s Web site. Duet also allows for device swapping so that programming changes are
not required when devices with DDDP are removed or replaced – a huge benefit for end users. The Duet platform is an extension AMX’s InConcert®
manufacturer partner program, which was developed to ensure seamless communication between partners’ devices and the AMX control system.
Data is specified in the ASCII format. All ASCII characters between the quotes “” should be recognised/transmitted. “\r” is a carriage return (0x0D)
Command: “AMX\r”
AVR750 Response:
“AMXB<Device-SDKClass=Receiver><Device-Make=ARCAM><Device-Model=AVR750><Device-Revision=x.y.z>\r”
Determine whether headphones are connected.
Example
Command/response sequence to request the headphone status where the
headphones are not connected:
Command: 0x21 0x01 0x02 0x01 0xF0 0x0D
Response: 0x21 0x01 0x02 0x00 0x01 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x02
Dl
0x01
Data
0xF0 – Request current headphone connection status
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x02
Ac
Answer code
Where Dl
0x01 (Data length)
x.y.z = RS232 protocol version number.
Data
0x00 – Headphones are not connected.
0x01 – Headphones are connected
Et
0x0D
AVR450 Response:
“AMXB<Device-SDKClass=Receiver><Device-Make=ARCAM><Device-Model=AVR450><Device-Revision=x.y.z>\r”
AVR380 Response:
“AMXB<Device-SDKClass=Receiver><Device-Make=ARCAM><Device-Model=AVR380><Device-Revision=x.y.z>\r”
4
Headphones (0x02)
5
FM genre (0x03)
Request information on the current station programme type from FM source
in a given zone. If FM is not selected on the given zone an error 0x85 is
returned.
Example
Command/response sequence to request the programme type on zone 1 where
the programme type is “POP MUSIC”:
Command: 0x21 0x01 0x03 0x01 0xF0 0x0D
Response: 0x21 0x01 0x03 0x00 0x09 0x50 0x4F 0x50 0x20 0x4D 0x55 0x53 0x49 0x43 0x0D
Software version (0x04)
Request the version number of the various pieces of software on the AVR.
Example
Command/response sequence to request the RS232 protocol version (1.4):
Command: 0x21 0x01 0x04 0x01 0xF0 0x0D
Response: 0x21 0x01 0x04 0x00 0x03 0xF0 0x01 0x04 0x0D
Save/Restore secure copy of settings (0x06)
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x03
Dl
0x01
Data1
Request information source:
0xF0 – FM program type
Et
0x0D
RESPONSE:
Force a restore of the factory default settings.
Example
Command/response sequence to restore factory defaults:
Command: 0x21 0x01 0x05 0x02 0xAA 0xAA 0x0D
Response: 0x21 0x01 0x05 0x00 0x00 0x0D
If the system is currently doing a save and another save is requested. The
second save will fail silently. If a command 0x1E is being processed this
command will fail with a answer code 0x85
Example
Command/response sequence to restore secure backup:
Command: 0x21 0x01 0x06 0x07 0x01 0x55 0x55 0x01 0x02 0x03 0x040x0D
Response: 0x21 0x01 0x06 0x00 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0X06
Dl
0x07
Data1
0x00 – Save secure backup
0x01 – Restore secure backup
Data2
0x55 (Confirmation data pattern to avoid accidental save/restore)
Data3
0x55 (Confirmation data pattern to avoid accidental save/restore)
Data4
Pin digit 1
Data5
Pin Digit 2
Data5
Pin Digit 3
Data7
Pin Digit 4
0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x03
Ac
Answer code
Et
Dl
Data length <n>
RESPONSE:
Data1 –
Data<n>
The radio programme type in ASCII characters
Byte:
Description:
St
0x21
Et
0x0D
Zn
0x01
Cc
0x06
Ac
Answer code
Dl
0x00
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x04
Dl
0x01
Data
0xF0 – Request RS232 version
0xF1 – Request Host version
0xF2 – Request OSD version
0xF3 – Request DSP version
0xF4 – Request NET version
0xF5 – Request IAP version
Et
0x0D
RESPONSE:
Restore factory default settings (0x05)
Force a restore of the secure copy of the settings. Note: If no secure copy has
been made, this command will return an answer code of 0x85.
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x04
Ac
Answer code
Dl
0x03
Data1
Echo data from command
Data2
Major version number
Data3
Minor version number
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x05
Dl
0x02
Data1
0xAA (Confirmation data pattern to avoid accidental restore)
Data2
0xAA (Confirmation data pattern to avoid accidental restore)
Et
0x0D
Simulate RC5 IR Command (0x08)
Simulate an RC5 command via the RS232 port. An additional status message
will be sent in most cases as a result of the IR command.
Example
Command/response sequence to RC5 16-17 (AVR volume down in zone 1):
Command: 0x21 0x01 0x08 0x02 0x10 0x11 0x0D
Response: 0x21 0x01 0x08 0x00 0x02 0x10 0x11 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x08
Dl
0x02
Data1
RC5 System code
Data2
RC5 Command code
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x08
Ac
Answer code
Dl
0x02
Data1
RC5 System code
Data2
RC5 Command code
Et
0x0D
RESPONSE:
6
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x05
Ac
Answer code
Dl
0x00
Et
0x0D
7
Display Information Type (0x09)
Set the VFD display information type (where applicable).
Request current source (0x1D)
COMMAND:
Byte:
Description:
The return data echoes the data sent.
St
0x21
Zn
Zone number
Example
Command/response sequence to set the display text to show the current FM
radio text with FM playing in zone 2:
Cc
0x09
Dl
0x01
Data
For all sources:
0x00 – Set the display to Processing mode
0xE0 – Cycle though all displayable information.
0xF0 – Request the current display type
Command: Response: 0x21 0x02 0x09 0x01 0x01 0x0D
0x21 0x02 0x09 0x00 0x01 0x01 0x0D
Request the source currently selected for a given zone.
Example
Command/response sequence to request the current source for Zone 1 where
the source is set to ‘SAT’:
Command:
Response:
0x21 0x01 0x1D 0x01 0xF0 0x0D
0x21 0x01 0x1D 0x00 0x01 0x04 0x0D
If the current source is FM:
0x01 – Set the display to Radio text
0x02 – Set the display to Programme type
0x03 – Set the display to Signal strength
If the current source is DAB (AVR450/750 only):
0x01 – Set the display to Radio text
0x02 – Set the display to Genre
0x03 – Set the display to Signal quality
0x04 – Set the display to Bit rate
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1D
Dl
0x01
Data
0xF0
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1D
Ac
Answer code
Dl
0x01
Data
The current source in the indicated zone:
0x00 – Follow Zone 1
0x01 – CD
0x02 – BD
0x03 – AV
0x04 – SAT
0x05 – PVR
0x06 – VCR
0x08 – AUX
0x09 – DISPLAY
0x0B – TUNER (FM)
0x0C – TUNER (DAB) (AVR450/750 only)
0x0E – NET
0x0F – USB
0x10 - STB
0x11 - GAME
Et
0x0D
If the current source is NET/USB
0x01 – Set the display to Track
0x02 – Set the display to Artist
0x03 - Set the display to Album
0x04 – Set the display to audio type
0x05 – Set the display to rate
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x09
Ac
Answer code
Dl
0x01
Data
The current display is returned, as for the command.
Et
0x0D
Headphone Over-ride (0x1F)
Activate/deactivate the mute relays (does not zero the volume).
Example
Command/response sequence to activate the mute relays:
Command: 0x21 0x01 0x1F 0x01 0x01 0x0D
Response: 0x21 0x01 0x1F 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1F
Dl
0x01
Data
0x00 – Headphone/Over-ride Clear (speakers muted if headphones present)
0x01 – Headphone/Over-ride Set (speakers unmuted if headphones present)
Et
0x0D
RESPONSE:
8
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1F
Ac
Answer code
Dl
0x01
Data1
Relay state
Et
0x0D
9
Input Command Specifications
Video selection (0x0A)
Changes the video input. Returns invalid (0x85) if OSD is showing setup
screen.
Example
Command/response sequence to change the video source for zone 1 to ‘PVR’:
Command:
0x21 0x01 0x0A 0x01 0x03 0x0D
Response: 0x21 0x01 0x0A 0x00 0x01 0x03 0x0D
Output Command Specifications
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0A
Dl
0x01
Data
Source:
0x00 – BD
0x01 – SAT
0x02 – AV
0x03 – PVR
0x04 – VCR
0x05 - Game
0x06 - STB
0xF0 – Request current input
Et
Byte:
Description:
St
0x21
Zn
Zone number
This command returns the volume even if the zone requested is in mute. The
“Request Mute status” command can be used to discover if the zone is muted.
Cc
0x0D
Dl
0x01
Response data format:
e.g. for volume 42dB: Data1=0x2A (42)
Example
Data
0x00 (0) – 0x63 (99) – Set the volume
0xF0 – Request the current volume
Et
0x0D
Set/Request Volume (0x0D)
Set or request the volume of a zone.
Command/response sequence for setting the volume in Zone 1 to 45dB:
Command:
0x21 0x01 0x0D 0x01 0x2D 0x0D
Response: 0x21 0x01 0x0D 0x00 0x01 0x2D 0x0D
0x0D
RESPONSE:
Select analogue/digital (0x0B)
Select an analogue/digital audio input for the current source. Returns invalid
(0x85) if OSD is showing setup screen.
Example
Command/response sequence to change the audio input to ‘digital’ in zone 1:
Command:
0x21 0x01 0x0B 0x01 0x01 0x0D
Response: 0x21 0x01 0x0B 0x00 0x01 0x01 0x0D
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0A
Ac
Answer code
Dl
0x01
Data
Response:
The current video source is returned, as for the command
Et
0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x0B
Dl
0x01
Data
0x00 – Use the analogue audio for the current source.
0x01 – Use the digital audio for the current source (if available).
0x02 – Use HDMI for the current source (if available).
0xF0 – Request the audio type in use for the current source.
0x0D
RESPONSE:
This command is only valid for zone 1.
Example
Command/response sequence for requesting the input video source where it
is CVBS
Command: 0x21 0x01 0x0C 0x01 0xF0 0x0D
Response: 0x21 0x01 0x0C 0x00 0x01 0x04 0x0D
Description:
St
0x21
Zn
Zone number
Cc
0x0D
Ac
Answer code
Dl
0x01
Data1
Zone volume, integer value:
0x00 (0) – 0x63 (99)
Et
0x0D
Request Mute status (0x0E)
Request the mute status of the audio in a zone.
Example
Command/response sequence to request the mute status of zone 1 where zone
1 is muted:
Command:
0x21 0x01 0x0E 0x01 0xF0 0x0D
Response: 0x21 0x01 0x0E 0x00 0x01 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x0E
Dl
0x01
Data
0xF0 – Request mute status
Et
0x0D
Description:
RESPONSE:
St
0x21
Byte:
Description:
Zn
Zone number
St
0x21
Cc
0x0B
Zn
Zone number
Ac
Answer code
Cc
0x0E
Dl
0x01
Ac
Answer code
Data
Response:
0x00 – Analogue audio is in use for the current source.
0x01 – Digital audio is in use for the current source.
0x02 – HDMI audio is in use for the current source.
Dl
0x01
P2
0x00 – Zone is muted
0x01 – Zone is not muted
Et
0x0D
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0C
Dl
0x01
Data
0x01 – HDMI.
0x02 – Component.
0x04 – CVBS.
0xF0 – Request the video type in use for the current source.
Et
0x0D
RESPONSE:
10
Byte:
Byte:
Et
Set/request the video input (CVBS/Component/HDMI) type in use for the
current source.
RESPONSE:
COMMAND:
Et
Set/Request video input type (0x0C)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0C
Ac
Answer code
Dl
0x01
Data
0x01 – HDMI.
0x02 – Component.
0x04 – CVBS.
Et
0x0D
Request direct mode status (0x0F)
Request the direct mode status on Zone 1.
Example
Command/response sequence to request the Direct mode status in zone 1
where the mode is direct:
Command:
0x21 0x01 0x0F 0x01 0xF0 0x0D
Response: 0x21 0x01 0x0F 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0F
Dl
0x01
Data
0xF0 – Request mode setting
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x0F
Ac
Answer code
Dl
0x01
Data
0x00 – ‘Direct mode’ is off
0x01 – ‘Direct mode’ is on
Et
0x0D
11
Request decode mode status — 2ch (0x10)
Request the decode mode for two-channel material in zone 1.
Example
Command/response sequence to request the decode mode in zone 1 where the
mode is Pro Logic II / x Movie Mode:
Command:
0x21 0x01 0x10 0x01 0xF0 0x0D
Response: 0x21 0x01 0x10 0x00 0x01 0x02 0x0D
Request RDS information (0x12)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x10
Dl
0x01
Data
0xF0 – Request decode mode
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
Request RDS information from the current radio station in a given zone. If FM
is not selected on the given zone an error 0x85 is returned.
Example
Command/response sequence to request the RDS information on FM in zone
1, where the response is “Playing your favourite music”.
Command:
0x21 0x01 0x12 0x01 0xF0 0x0D
Response: 0x21 0x01 0x12 0x00 0x1C 0x00 0x50 0x6C 0x61 0x79 0x69 0x6E 0x67 0x20 0x79 0x6F 0x75 0x72 0x20 0x66 0x61 0x76 0x6F 0x75 0x72 0x69 0x74 0x65 0x20 0x6D 0x75 0x73 0x69 0x63 0x0D
Zone number
Cc
0x12
Dl
0x01
Data1
Request information source:
0xF0 – FM
Et
0x0D
RESPONSE:
0x21
0x10
Zn
Zone number
Ac
Answer code
Cc
0x12
Dl
0x01
Ac
Answer code
Data
0x01 – Stereo
0x02 – Dolby PLII / x Movie Mode
0x03 – Dolby PLII / x Music Mode
0x05 – Dolby PLII / x Game
0x06 – Dolby PL
0x07 – Neo:6 Cinema
0x08 – Neo:6 Music
0x09 - 5/7 Ch Stereo
Dl
Data length <n>
Data1 –
Data<n>
The radio programme type in ASCII characters
Et
0x0D
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x11
Dl
0x01
Data
0xF0 – Request decode mode
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x11
Ac
Answer code
Dl
0x01
Data
0x01 – Stereo down-mix
0x02 – Multi-channel mode
0x03 – Dolby D EX / DTS-ES mode
0x04 – Dolby PL IIx movie mode
0x05 – Dolby PL IIx music mode
Et
12
0x21
Zn
Description:
Set/request the Video Output Resolution of zone 1.
Example
Example
Command/response sequence to request the decode mode in zone 1 where the
mode is Pro Logic IIx Movie Mode:
Command: 0x21 0x01 0x11 0x01 0xF0 0x0D
Response: 0x21 0x01 0x11 0x00 0x01 0x04 0x0D
Description:
St
St
Set/request Video Output Resolution (0x13)
Request the decode mode for multi-channel material in zone 1.
Byte:
Byte:
Et
Request Decode mode status — MCH (0x11)
COMMAND:
Command/response sequence to request the video output in zone 1 where the
resolution is 1080p:
Command:
0x21 0x01 0x13 0x01 0xF0 0x0D
Response: 0x21 0x01 0x13 0x00 0x01 0x05 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x13
Dl
0x01
Data
0x02 – Set resolution to SD Progressive.
0x03 – Set resolution to 720p.
0x04 – Set resolution to 1080i.
0x05 – Set resolution to 1080p.
0x06 – Set resolution to ‘Preferred’.
0x07 – Set resolution to Bypass.
0x08 - Set the resolution to 4k
0xF0 – Request the video output.
0xF1 – Increment the resolution setting.
0xF2 – Decrement the resolution setting.
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x13
Ac
Answer code
Dl
0x01
Data
0x02 – SD Progressive.
0x03 – 720p.
0x04 – 1080i.
0x05 – 1080p
0x06 – ‘Preferred’
0x07 – Bypass
0x08 - 4k
Et
0x0D
0x0D
13
Menu Command Specifications
Request menu status (0x14)
Request which (if any) menu is open in the unit.
Example
Command/response sequence to request which menu is open where the ‘Trim’
menu is open:
Command:
0x21 0x01 0x14 0x01 0xF0 0x0D
Response: 0x21 0x01 0x14 0x00 0x01 0x03 0x0D
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x14
Dl
0x01
Data
0xF0 – Request the open menu state
Et
0x0D
RESPONSE:
Request the current tuner preset number. If the tuner is not selected on the
given zone an error 0x85 is returned.
Example
Command/response sequence to request the preset number where the present
number is 10 on zone 1:
Command:
0x21 0x01 0x15 0x01 0xF0 0x0D
Response: 0x21 0x01 0x15 0x00 0x01 0x0A 0x0D
Request the current DAB station selected. If DAB is not selected on the given
zone an error 0x85 is returned.
Example
Command/response sequence to request the DAB station selection where the
station is called “DAB STATION 2” in zone 1:
Command: 0x21 0x01 0x18 0x01 0xF0 0x0D
Response: 0x21 0x01 0x18 0x00 0x10 0x44 0x41 0x42 0x20 0x53 0x54 0x41 0x54 0x49 0x4F 0x4E 0x20 0x32 0x20 0x20 0x20 0x0D
The returned frequency is calculated as follows:
FM freq. (MHz) = reported freq. (MHz)
FM freq. (kHz) = reported freq. (kHz)
For these reasons, this command may return values that cannot be translated
into ASCII characters.
14
0x21
Zn
Zone number
Cc
0x18
Dl
0x01
Data
0xF0 – Request the current DAB station
Et
0x0D
RESPONSE:
Byte:
Description:
0x21
St
0x21
Zn
0x01
Zn
Zone number
Cc
0x14
Cc
0x18
Ac
Answer code
Ac
Answer code
Dl
0x01
Dl
Data length, fixed to 16 bytes (ASCII characters)
Data
0x00 – No menu is open
0x02 – Set-up Menu Open
0x03 – Trim Menu Open
0x04 – Bass Menu Open
0x05 – Treble Menu Open
0x06 – Sync Menu Open
0x07 – Sub Menu Open
0x08 – Tuner Menu Open
0x09 – Network menu Open
0x0A – USB Menu Open
Data1 –
Data128
The service label of the DAB station in ASCII characters.
The data is padded to 16 bytes with the space character (0x20)
Et
0x0D
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x15
Dl
0x01
Data
0x01 – 0x32 (1-50) number of required preset.
0xF0 – Request the current preset number.
Et
0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x15
Ac
Answer code
Dl
0x01
Data
0xFF – Currently no preset selected
0x01- 0x32: (1-50) the current preset number.
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x16
Dl
0x01
Data1
0x00 – Decrement tuner frequency by 1 step.
0x01 – Increment tuner frequency by 1 step.
0xF0 – Request the current tuner frequency.
If the tuner is not selected on the given zone an error 0x85 is returned.
Example
Command/response sequence to increment the FM tuning from 85.0MHz to
85.05MHz in zone 1:
Command:
0x21 0x01 0x16 0x01 0x01 0x0D
Response: 0x21 0x01 0x16 0x00 0x02 0x55 0x05 0x0D
Description:
St
Description:
Prog. Type/Category (0x19) (AVR450/750 only)
Request information on the current station programme type from DAB source
in a given zone. If DAB is not selected on the given zone an error 0x85 is
returned.
Example
Command/response sequence to request the programme type on zone 1 where
the programme type is “POP MUSIC”:
Command:
0x21 0x01 0x19 0x01 0xF0 0x0D
Response:
0x21 0x01 0x19 0x00 0x10 0x50 0x4F 0x50 0x20 0x4D 0x55 0x53 0x49 0x43 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x0D
DLS/PDT info. (0x1A) (AVR450/750 only)
Increment/Decrement the tuner frequency in 0.05MHz steps (FM).
Byte:
St
RESPONSE:
Tune (0x16)
COMMAND:
Byte:
Et
Request tuner preset (0x15)
Request DAB station (0x18) (AVR450/750 only)
COMMAND:
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x16
Ac
Answer code
Dl
0x02 (Data length)
Data1
FM: New frequency (MHz)
Data2
FM: New frequency (10’s kHz)
Et
0x0D
Request DLS/PDT information (digital radio text) from the current radio
station in a given zone. If DAB is not selected on the given zone an error 0x85
is returned.
Example
Command/response sequence to request the DLS information on DAB in zone
1, where the response is “Playing your favourite music”.
Command:
0x21 0x01 0x1A 0xF0 0x0D
Response: 0x21 0x01 0x1A 0x00 0x80 0x00 0x50 0x6C 0x61 0x79 0x69 0x6E 0x67 0x20 0x79 0x6F 0x75 0x72 0x20 0x66 0x61 0x76 0x6F 0x75 0x72 0x69 0x74 0x65 0x20 0x6D 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x19
Dl
0x01
Data1
Request information source:
0xF0 – DAB program type
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x19
Ac
Answer code
Dl
Data length, fixed to 16 bytes (ASCII characters)
Data1 –
Data128
The radio programme type in ASCII characters.
The data is padded to 16 bytes with the space character (0x20)
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1A
Dl
0x01
Data1
Request information source:
0xF0 – DAB
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1A
Ac
Answer code
Dl
Data length, fixed to 128 bytes (ASCII characters)
Data1 –
Data<n>
The radio programme type in ASCII characters.
The data is padded to 128 bytes with the space character (0x20)
Et
0x0D
15
Request preset details (0x1B)
Request details of tuner presets.
Example
Command/response sequence to request preset 1 where the response is a preset
on DAB called “DAB STATION 2”:
Command: 0x21 0x01 0x1B 0x01 0x01 0x0D
Response: 0x21 0x01 0x1B 0x00 0x0F 0x01 0x02 0x44 0x41 0x42 0x20 0x53 0x54 0x41 0x54 0x49 0x4F 0x4E 0x20 0x32 0x0D
Setup Adjustment Command Specifications
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1B
Dl
0x01
Data
0x01- 0x32: (1-50) The number of the required preset
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1B
Ac
Answer code
Dl
Data length <n>
Data1
0x01- 0x32: (1-50) The number of the requested preset
Data2
0x01 : FM frequency
0x02 : FM RDS name
0x03 : DAB (AVR450/750 only)
Treble Equalisaton (0x35)
Adjust the amount of treble equalisation.
Example
Command/response sequence to set the treble to -2dB:
Command: 0x21 0x01 0x35 0x01 0x82 0x0D
Response: 0x21 0x01 0x35 0x00 0x01 0x82 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x35
Dl
0x01
Data
0x00 — 0x0C – Set treble to 0dB — +12dB
0x81 — 0x8C – Set treble to -1dB — -12dB
0xF0 – Request current treble value
0xF1 – Increment treble by 1dB
0xF2 – Decrement treble by 1dB
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x35
Ac
Answer code
Dl
0x01
Data3
FM: New frequency (MHz)
Data1
0x00 — 0x0C – Treble is 0dB — +12dB
0x81 — 0x8C – Treble is -1dB — -12dB
Data4
FM: New frequency (10’skHz)
Et
0x0D
Data<n>
The name (DAB, FM if RDS)
in ASCII characters
Et
0x0D
Bass Equalisation (0x36)
Adjust the amount of bass equalisation.
Example
Command/response sequence to increase the bass EQ by 1dB when it was 0dB:
Command: 0x21 0x01 0x36 0x01 0xF1 0x0D
Response: 0x21 0x01 0x36 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x36
Dl
0x01
Data
0x00 — 0x0C – Set bass to 0dB — +12dB
0x81 — 0x8C – Set bass to -1dB — -12dB
0xF0 – Request current bass value
0xF1 – Increment bass by 1dB
0xF2 – Decrement bass by 1dB
Et
0x0D
RESPONSE:
Network Command Specifications
Network playback status (0x1C)
Network message format.
If the network is not selected on the given zone an error 0x85 is returned.
Example
Command/response sequence where the network module is playing a file “File.
mp3” on zone 1:
Command: 0x21 0x01 0x1C 0x01 0xF0 0x0D
Response: 0x21 0x01 0x1C 0x00 0x09 0x01 0x46 0x69 0x6C 0x65 0x2e 0x6d 0x70 0x33 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1C
Dl
0x01
Data
0xF0 – Request Network playback status
Et
0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x36
Ac
Answer code
Dl
0x01
Data1
0x00 — 0x0C – Bass is 0dB — +12dB
0x81 — 0x8C – Bass is -1dB — -12dB
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x1C
Room Equalisation (0x37)
Ac
Answer code
Dl
Data length <n>
Turn the room equalisation system on/off.
Data1
0x00 – Navigating
0x01 – Playing
0x02 – Paused
0xFF - Busy/Not Playing
Data2 –
Data<n>
name of folder in ASCII if navigating
name of file in ASCII if playing or paused
Et
0x0D
Example
Command/response sequence to turn the room equalisation system on:
Command: 0x21 0x01 0x37 0x01 0xF1 0x0D
Response: 0x21 0x01 0x37 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x37
Dl
0x01
Data
0xF0 – Request current Room EQ state
0xF1 – Room EQ on
0xF2 – Room EQ off
Et
0x0D
RESPONSE:
16
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x37
Ac
Answer code
Dl
0x01
Data1
0x00 – Room EQ is off
0x01 – Room EQ is on
0x02 – Room EQ has not been calculated and is therefore off
Et
0x0D
17
Dolby Volume (0x38)
Control the status of the Dolby volume system.
Example
Command/response sequence to turn the Dolby Volume system on:
Command: 0x21 0x01 0x38 0x01 0x01 0x0D
Response: 0x21 0x01 0x38 0x00 0x01 0x02 0x0D
Balance (0x3B)
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x38
Dl
0x01
Data
0x00 – Dolby Volume off
0x01 – Dolby Volume on
0xF0 – Request current Dolby Volume mode
Et
0x0D
Adjust the balance control.
Example
Command/response sequence to set the balance to -3:
Command: 0x21 0x01 0x3B 0x01 0x83 0x0D
Response: 0x21 0x01 0x3B 0x00 0x01 0x83 0x0D
RESPONSE:
Dolby Leveller (0x39)
Control the status of the leveller component of the Dolby volume system.
Example
Command/response sequence to set the Dolby Leveller to 5:
Command: 0x21 0x01 0x39 0x01 0x05 0x0D
Response: 0x21 0x01 0x39 0x00 0x01 0x05 0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x38
Ac
Answer code
Dl
Zone number
Cc
0x3B
Dl
0x01
Data
0x00 — 0x06 – Set the balance to 0 — 6
0x81 — 0x86 – Set the balance to -1 — -6
0xF0 – Request current balance
0xF1 – Increment the balance by 1dB
0xF2 – Decrement the balance by 1dB
Et
0x0D
Description:
0x21
Zn
Zone number
0x01
Cc
0x3B
Data1
0x00 – Dolby Volume is off
0x01 – Dolby Volume is on
Ac
Answer code
Dl
0x01
Et
0x0D
Data1
0x00 — 0x06 – Balance is 0 — 6
0x81 — 0x86 – Balance is -1 — -6
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x39
Dl
0x01
Data
0x00 — 0x0A – Set Dolby Leveller to 0 — 10
0xF0 – Request current Dolby Leveller setting
0xF1 – Increment Dolby Leveller setting
0xF2 – Decrement Dolby Leveller setting
0xFF – Turn off Dolby Leveller
Dolby PLII/x Music Dimension (0x3C)
Adjust the ‘Dimension’ parameter of the Dolby PLII/x Music processor.
Example
Command/response sequence to set the dimension to -1:
Command: 0x21 0x01 0x3C 0x01 0x81 0x0D
Response: 0x21 0x01 0x3C 0x00 0x01 0x81 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3C
Dl
0x01
Data
0x00 — 0x03 – Set the Dolby PLII/x Music Dimension parameter to 0 — 3
0x81 — 0x83 – Set the Dolby PLII/x Music Dimension parameter to -1 — -3
0xF0 – Request current Dolby PLII/x Music Dimension setting
0xF1 – Increment the Dolby PLII/x Music Dimension
0xF2 – Decrement the Dolby PLII/x Music Dimension
Et
0x0D
0x0D
Byte:
Description:
RESPONSE:
St
0x21
Byte:
Description:
Zn
Zone number
St
0x21
Cc
0x39
Zn
Zone number
Ac
Answer code
Cc
0x3C
Dl
0x01
Ac
Answer code
Data1
0x00 — 0x0A – Dolby Leveller setting is 0 — 10
0xFF – Dolby Leveller is off
Dl
0x01
Data1
0x00 — 0x03 – The Dolby PLII/x Music Dimension parameter is 0 — 3
0x81 — 0x83 – The Dolby PLII/x Music Dimension parameter is -1 — -3
Et
0x0D
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3A
Dl
0x01
Data
0x00 — 0x0F – Set the calibration offset to 0 — 15dB
0x80 — 0x8F – Set the calibration offset to -1 — -15dB
0xF0 – Request current calibration offset
0xF1 – Increment the calibration offset by 1dB
0xF2 – Decrement the calibration offset by 1dB
Et
Dolby PLII/x Music Centre Width (0x3D)
Adjust the ‘Centre Width’ parameter of the Dolby PLII/x music processor.
Example
Command/response sequence to set the centre width to 3:
Command: 0x21 0x01 0x3D 0x01 0x03 0x0D
Response: 0x21 0x01 0x3D 0x00 0x01 0x03 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3D
Dl
0x01
Data
0x00 — 0x07 – Set the Dolby PLII/x Music Centre Width parameter to 0 — 7
0xF0 – Request current Dolby PLII/x Music Centre Width setting
0xF1 – Increment the Dolby PLII/x Music Centre Width
0xF2 – Decrement the Dolby PLII/x Music Centre Width
Et
0x0D
0x0D
RESPONSE:
Byte:
Description:
RESPONSE:
St
0x21
Byte:
Description:
Zn
Zone number
St
0x21
Cc
0x3A
Zn
Zone number
Ac
Answer code
Cc
0x3D
Dl
0x01
Ac
Answer code
Data1
0x00 — 0x0F – Calibration offset is 0 — 15dB
0x80 — 0x8F – Calibration offset is -1 — -15dB
Dl
0x01
Data1
0x00 — 0x07 – The Dolby PLII/x Music Centre Width parameter is 0 — 7
0x0D
Et
0x0D
Et
18
0x21
Zn
St
Et
Example
Command/response sequence to set the calibration offset to -5dB:
Command: 0x21 0x01 0x3A 0x01 0x85 0x0D
Response: 0x21 0x01 0x3A 0x00 0x01 0x85 0x0D
Description:
St
RESPONSE:
RESPONSE:
Adjust the calibration offset of the Dolby volume system.
Byte:
Byte:
Et
Dolby Volume Calibration Offset (0x3A)
COMMAND:
19
Dolby PLII/x Music Panorama (0x3E)
Turn on/off the Panorama setting of the Dolby PLII/x Music processor.
Example
Command/response sequence to turn Dolby PLII/x Music Panorama on:
Command: 0x21 0x01 0x3E 0x01 0xF1 0x0D
Response: 0x21 0x01 0x3E 0x00 0x01 0xF1 0x0D
Compression (0x41)
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3E
Dl
0x01
Data
0xF0 – Request current Dolby PLII/x Music Panorama setting
0xF1 – Set Dolby PLII/x Music Panorama on
0xF2 – Set Dolby PLII/x Music Panorama off
Et
0x0D
Adjust the dynamic range compression setting.
Example
Command/response sequence to set compression to medium:
Command: 0x21 0x01 0x41 0x01 0x01 0x0D
Response: 0x21 0x01 0x41 0x00 0x01 0x01 0x0D
RESPONSE:
Adjust the value of subwoofer trim.
Example
Command/response sequence to set the subwoofer trim to -1.5dB:
Command: 0x21 0x01 0x3F 0x01 0x85 0x0D
Response: 0x21 0x01 0x3F 0x00 0x01 0x85 0x0D
Zone number
Cc
0x41
Dl
0x01
Data
0x00 – Compression off
0x01 – Set compression to medium
0x02 – Set compression to high
0xF0 – Request current compression setting
Et
0x0D
RESPONSE:
0x21
Byte:
Description:
Zn
Zone number
St
0x21
Cc
0x3E
Zn
Zone number
Ac
Answer code
Cc
0x41
Dl
0x01
Ac
Answer code
Data1
0x00 – Dolby PLII/x Music Panorama is off
0x01 – Dolby PLII/x Music Panorama is on
Dl
0x01
Data1
0x00 – Compression off
0x01 – medium
0x02 – high
Et
0x0D
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3F
Dl
0x01
Data
0x00 — 0x14 – Set positive subwoofer trim in 0.5dB steps (e.g. 0x02 = +1.0dB)
0x81 — 0x94 – Set negative sub. trim in 0.5dB steps (e.g. 0x82 = -1.0dB)
0xF0 – Request current subwoofer trim value
0xF1 – Increment the subwoofer trim by 1dB
0xF2 – Decrement the subwoofer trim by 1dB
0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x3F
Request incoming video parameters (0x42)
Request the incoming video resolution, refresh rate and aspect ratio.
Example
Command/response sequence to request video parameters, where the video is
1280x720 (720p) 50Hz 16:9:
Command: 0x21 0x01 0x42 0x01 0xF0 0x0D
Response: 0x21 0x01 0x42 0x00 0x07 0x05 0x00 0x02 0xD0 0x32 0x00 0x02 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x42
Dl
0x01
Data
0xF0 – Request incoming video parameters
Et
0x0D
RESPONSE:
Ac
Answer code
Dl
0x01
Byte:
Description:
Data1
0x00 — 0x14 – Positive subwoofer trim in 0.5dB steps (e.g. 0x02 = +1.0dB)
0x81 — 0x94 – Negative subwoofer trim in 0.5dB steps (e.g. 0x82 = -1.0dB)
St
0x21
Zn
Zone number
0x0D
Cc
0x42
Ac
Answer code
Dl
0x07
Data1
Horizontal resolution MSB (e.g. for 720p: 0x05 since 1280 = 0x0500)
Data2
Horizontal resolution LSB (e.g. for 720p: 0x00 since 1280 = 0x0500)
Data3
Vertical resolution MSB (e.g. for 720p: 0x02 since 720 = 0x02D0)
Data4
Vertical resolution LSB (e.g. for 720p: 0xD0 since 720 = 0x02D0)
Data5
Refresh rate for full image update (half the field rate for interlaced signals)
(e.g. for 50Hz progressive: 0x32)
Data6
Interlaced flag:
0x00 – Progressive
0x01 – Interlaced
Data7
Aspect ratio:
0x00 – Undefined
0x01 – 4:3
0x02 – 16:9
Et
0x0D
Et
Example
Command/response sequence to set the lipsync delay to 50ms:
Command: 0x21 0x01 0x40 0x01 0x0A 0x0D
Response: 0x21 0x01 0x40 0x00 0x01 0x0A 0x0D
0x21
Zn
Description:
RESPONSE:
Adjust the lipsync delay value.
Description:
St
St
Et
Lipsync Delay (0x40)
Byte:
Byte:
Et
Subwoofer Trim (0x3F)
COMMAND:
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x40
Dl
0x01
Data
0x00 — 0x32 – set the lipsync delay in 5ms steps (e.g. 0x08 = 40ms)
0xF0 – Request current lipsync delay value
0xF1 – Increment the lipsync delay by 5ms
0xF2 – Decrement the lipsync delay by 5ms
Et
0x0D
RESPONSE:
20
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x40
Ac
Answer code
Dl
0x01
Data1
0x00 — 0x32 – the lipsync delay in 5ms steps (e.g. 0x10 = 80ms)
Et
0x0D
21
Request incoming audio format (0x43)
Request the incoming audio format.
Example
Command/response sequence to request the incoming audio format, where the
format is Dolby Digital 5.1:
Command: 0x21 0x01 0x43 0x01 0xF0 0x0D
Response: 0x21 0x01 0x43 0x00 0x02 0x02 0x1A 0xD0
Request incoming audio sample rate (0x44)
COMMAND:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x43
Dl
0x01
Data
0xF0 – Request incoming audio format
Et
0x0D
Request the incoming audio sample rate.
Example
Command/response sequence to request the incoming audio sample rate,
where the rate is 48kHz:
Command: 0x21 0x01 0x44 0x01 0xF0 0x0D
Response:
0x21 0x01 0x44 0x00 0x01 0x02 0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x44
Dl
0x01
Data
0xF0 – Request incoming audio sample rate
Et
0x0D
RESPONSE:
Byte:
Description:
Byte:
Description:
St
0x21
St
0x21
Zn
Zone number
Zn
Zone number
Cc
0x43
Cc
0x44
Ac
Answer code
Ac
Answer code
Dl
0x02
Dl
0x01
Data1
Audio stream format:
0x00 – PCM
0x01 – Analogue Direct
0x02 – Dolby Digital
0x03 – Dolby Digital EX
0x04 – Dolby Digital Surround
0x05 – Dolby Digital Plus
0x06 – Dolby Digital True HD
0x07 – DTS
0x08 – DTS 96/24
0x09 – DTS ES Matrix
0x0A – DTS ES Discrete
0x0B – DTS ES Matrix 96/24
0x0C – DTS ES Discrete 96/24
0x0D – DTS HD Master Audio
0x0E – DTS HD High Res Audio
0x0F – DTS Low Bit Rate
0x10 – DTS Core
0x13 – PCM Zero
0x14 – Unsupported
0x15 – Undetected
Data1
Incoming audio sample rate:
0x00 – 32 KHz
0x01 – 44.1 KHz
0x02 – 48 KHz
0x03 – 88.2 KHz
0x04 – 96 KHz
0x05 – 176.4 KHz
0x06 – 192 KHz
0x07 – Unknown
0x08 – Undetected
Et
0x0D
Data2
Et
22
COMMAND:
Audio channel configuration:
0x00 – Dual Mono
0x01 – Centre only
0x02 – Stereo only
0x03 – Stereo + mono surround
0x04 – Stereo + Surround L & R
0x05 – Stereo + Surround L & R + mono Surround Back
0x06 – Stereo + Surround L & R + Surround Back L & R
0x07 – Stereo + Surround L & R containing matrix information for surround back L&R
0x08 – Stereo + Centre
0x09 – Stereo + Centre + mono surround
0x0A – Stereo + Centre + Surround L & R
0x0B – Stereo + Centre + Surround L & R + mono Surround Back
0x0C – Stereo + Centre + Surround L & R + Surround Back L & R
0x0D – Stereo + Centre + Surround L & R containing matrix information for surround back L&R
0x0E – Stereo Downmix Lt Rt
0x0F – Stereo Only (Lo Ro)
0x10 – Dual Mono + LFE
0x11 – Centre + LFE
0x12 – Stereo + LFE
0x13 – Stereo + single surround + LFE
0x14 – Stereo + Surround L & R + LFE
0x15 – Stereo + Surround L & R + mono Surround Back + LFE
0x16 – Stereo + Surround L & R + Surround Back L & R + LFE
0x17 – Stereo + Surround L & R + LFE
0x18 – Stereo + Centre + LFE containing matrix information for surround back L&R
0x19 – Stereo + Centre + single surround + LFE
0x1A – Stereo + Surround L & R + LFE (Standard 5.1)
0x1B – Stereo + Centre + Surround L & R + mono Surround Back + LFE
(6.1, e.g. DTS ES Discrete)
0x1C – Stereo + Centre + Surround L & R + Surround Back L & R + LFE (7.1)
0x1D – Stereo + Centre + Surround L & R + LFE, containing matrix information for surround back L&R (6.1 e.g. Dolby Digital EX)
0x1E – Stereo Downmix (Lt Rt) + LFE
0x1F – Stereo Only (Lo Ro) + LFE
0x20 – Unknown
0x21 – Undetected
0x0D
Set/Request Sub Stereo Trim (0x45)
Set/Request the subwoofer trim value for stereo mode.
Example
Command/response sequence to set the sub stereo trim to -1.5dB:
Command: 0x21 0x01 0x45 0x01 0x83 0x0D
Response:
0x21 0x01 0x45 0x00 0x01 0x83 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x45
Dl
0x01
Data
0x00 – set the Sub Stereo Trim value to 0dB
0x81 — 0x94 – set the Sub Stereo Trim value to -0.5dB — -10.00dB
0xF0 – Request Sub Stereo Trim value
0xF1 – Increment Sub Stereo Trim value by 0.5dB
0xF2 – Decrement Sub Stereo Trim value by 0.5dB
Et
0x0D
RESPONSE:
Set/Request Brightness (0x46)
Set/Request the brightness control value.
Example
Command/response sequence to set the brightness to -4:
Command: 0x21 0x01 0x46 0x01 0x84 0x0D
Response:
0x21 0x01 0x46 0x00 0x01 0x84 0x0D
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x45
Ac
Answer code
Dl
0x01
Data1
0x00, 0x81 — 0x94 – Sub Stereo Trim value in -0.5dB steps
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x46
Dl
0x01
Data
0x00 — 0x32 – set the Brightness value to 0 — 50.
0x81 — 0xB2 – set the Brightness value to -1 — -50.
0xF0 – Request the current Brightness value.
0xF1 – Increment Brightness value by 1.
0xF2 – Decrement Brightness value by 1.
Et
0x0D
RESPONSE:
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x46
Ac
Answer code
Dl
0x01
Data1
0x00 — 0x32 – Brightness value 0 — 50
0x81 — 0xB2 – Brightness value -1 — -50
Et
0x0D
23
Set/Request Contrast (0x47)
Set/Request the contrast control value.
Example
Command/response sequence to set the contrast to 4:
Command: 0x21 0x01 0x47 0x01 0x04 0x0D
Response:
0x21 0x01 0x47 0x00 0x01 0x04 0x0D
Set/Request Edge Enhancement (0x4A)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x47
Dl
0x01
Data
0x00 — 0x32 – set the Contrast value to 0 — 50.
0x81 — 0xB2 – set the Contrast value to -1 — -50.
0xF0 – Request the current Contrast value.
0xF1 – Increment Contrast value by 1.
0xF2 – Decrement Contrast value by 1.
Et
0x0D
Set/Request the Edge Enhancement value.
Example
Command/response sequence to set the Edge Enhancement value to 10:
Command: 0x21 0x01 0x4A 0x01 0x0A 0x0D
Response:
0x21 0x01 0x4A 0x00 0x01 0x0A 0x0D
Set/Request the colour control value.
Example
Command/response sequence to increment the colour value, where the value
becomes +3:
Command: 0x21 0x01 0x48 0x01 0xF1 0x0D
Response:
0x21 0x01 0x48 0x00 0x01 0x03 0x0D
Example
Command/response sequence to request the current fim mode, where the
mode is auto:
Command: 0x21 0x01 0x49 0x01 0xF0 0x0D
Response:
0x21 0x01 0x49 0x00 0x01 0x00 0x0D
0x21
Zn
0x01
Cc
0x4A
Dl
0x01
Data
0x00 — 0x32 – Set the Edge Enhancement value to 0 — 50.
0xF0 – Request current Edge Enhancement value.
0xF1 – Increment Edge Enhancement value by 1.
0xF2 – Decrement Edge Enhancement value by 1.
Et
0x0D
Byte:
Description:
Description:
St
0x21
St
0x21
Zn
Zone number
Zn
Zone number
Cc
0x4A
Cc
0x47
Ac
Answer code
Ac
Answer code
Dl
0x01
Dl
0x01
Data1
0x00 — 0x32 – Edge Enhancement value to 0 — 50.
Data1
0x00 — 0x32 – Contrast value 0 — 50
0x81 — 0xB2 – Contrast value -1 — -50
Et
0x0D
Et
0x0D
Set/Request Noise Reduction (0x4C)
Set/Request the Noise Reduction value.
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x48
Dl
0x01
Data
0x00 — 0x32 – set the Colour value to 0 — 50.
0x81 — 0xB2 – set the Colour value to -1 — -50.
0xF0 – Request the current Colour value.
0xF1 – Increment Colour value by 1.
0xF2 – Decrement Colour value by 1.
Et
0x0D
Example
Command/response sequence to set the Noise Reduction value to ‘Low’:
Command: 0x21 0x01 0x4C 0x01 0x01 0x0D
Response:
0x21 0x01 0x4C 0x00 0x01 0x01 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4C
Dl
0x01
Data
0x00 – Set Noise Reduction to Off.
0x01 – Set to Noise Reduction to Low.
0x02 – Set Noise Reduction to Medium.
0x03 – Set Noise Reduction to High.
0xF0 – Request current Noise Reduction value.
0xF1 – Increment Noise Reduction value by 1.
0xF2 – Decrement Noise Reduction value by 1.
Et
0x0D
Byte:
Description:
RESPONSE:
St
0x21
Byte:
Description:
Zn
Zone number
St
0x21
Cc
0x48
Zn
Zone number
Ac
Answer code
Cc
0x4C
Dl
0x01
Ac
Answer code
Data1
0x00 — 0x32 – Colour value 0 — 50
0x81 — 0xB2 – Colour value -1 — -50
Dl
0x01
Data1
0x00 – Noise Reduction is Off.
0x01 – Noise Reduction is Low.
0x02 – Noise Reduction is Medium.
0x03 - Noise Reduction is High.
Et
0x0D
Et
Set/Request the Film Mode.
Description:
St
Byte:
RESPONSE:
Set/Request Film Mode (0x49)
Byte:
RESPONSE:
RESPONSE:
Set/Request Colour (0x48)
COMMAND:
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x49
Dl
0x01
Data
0x00 – Set Film Mode to Auto.
0x01 – Set Film Mode to Off.
0xF0 – Request current FIlm Mode.
Et
0x0D
RESPONSE:
24
Byte:
Description:
St
0x21
Zn
Zone number
Cc
0x49
Ac
Answer code
Dl
0x01
Data1
0x00 – Picture Film is Auto.
0x01 – Picture Film is Off.
Et
0x0D
25
Set/Request MPEG Noise Reduction (0x4D)
Set/Request the MPEG Noise Reduction value.
Example
Command/response sequence to set the MPEG Noise Reduction value to ‘Off ’:
Command: 0x21 0x01 0x4A 0x01 0x00 0x0D
Response:
0x21 0x01 0x4A 0x00 0x00 0x01 0x0D
Set/Request Output Frame Rate (0x50)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4D
Dl
0x01
Data
0x00 – Set MPEG Noise Reduction to Off.
0x01 – Set to MPEG Noise Reduction to Low.
0x02 – Set MPEG Noise Reduction to Medium.
0x03 – Set MPEG Noise Reduction to High.
0xF0 – Request current MPEG Noise Reduction value.
0xF1 – Increment MPEG Noise Reduction value by 1.
0xF2 – Decrement MPEG Noise Reduction value by 1.
Et
0x0D
Set/Request whether the Zone 1 OSD is shown.
Example
Command/response sequence to set the Zone 1 OSD to ‘Off ’:
Command: 0x21 0x01 0x4A 0x01 0xF2 0x0D
Response:
0x21 0x01 0x4A 0x00 0x00 0x01 0x0D
Example
Command/response sequence to set the frame rate to Auto:
Command: 0x21 0x01 0x50 0x01 0x00 0x0D
Response:
0x21 0x01 0x50 0x00 0x01 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x50
Dl
0x01
Data
0x00 – Set the frame rate to Auto.
0x01 – Set the frame rate to follow the source.
0x02 – Set the frame rate to 50Hz.
0x03 – Set the frame rate to 60Hz.
0xF0 – Request the current frame rate.
0xF1 – Increment setting.
0xF2 – Decrement setting.
Et
0x0D
RESPONSE:
RESPONSE:
Set/Request Zone 1 OSD on/off (0x4E)
Set/Request the video output frame rate.
Byte:
Description:
Byte:
Description:
St
0x21
St
0x21
Zn
Zone number
Zn
Zone Number
Cc
0x4D
Cc
0x50
Ac
Answer code
Ac
Answer code
Dl
0x01
Dl
0x01
Data1
0x00 – MPEG Noise Reduction is Off.
0x01 – MPEG Noise Reduction is Low.
0x02 – MPEG Noise Reduction is Medium.
0x03 – MPEG Noise Reducton is High.
Data1
0x00 – Auto.
0x01 – Frame rate is set to follow the source.
0x02 – 50Hz.
0x03 – 60Hz.
Et
0x0D
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4E
Dl
0x01
Data
0xF0 – Request current Zone 1 OSD on/off state.
0xF1 – Set Zone 1 OSD to On.
0xF2 – Set Zone 1 OSD to Off.
Et
0x0D
RESPONSE:
Set/Request Video Output Switching (0x4F)
Set/Request the HDMI video output selection.
Example
Command/response sequence to set the video output to HDMI output 1:
Command: 0x21 0x01 0x4F 0x01 0x02 0x0D
Response:
0x21 0x01 0x4F 0x00 0x01 0x02 0x0D
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4E
Ac
Answer code
Dl
0x01
Data1
0x00 – Zone 1 OSD is On.
0x01 – Zone 1 OSD is Off.
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4F
Dl
0x01
Data
0x02 – Set HDMI Output 1.
0x03 – Set HDMI Output 2.
0x04 – Set HDMI Output 1 & 2.
0xF0 – Request current video output switching setting.
Et
0x0D
RESPONSE:
26
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x4F
Ac
Answer code
Dl
0x01
Data1
0x02 – HDMI Output 1.
0x03 – HDMI Output 2.
0x04 – HDMI Output 1 & 2.
Et
0x0D
27
RS232 v2.0 commands
Set/request input name (0x20)
This command returns the name of an input if renamed by the user. It can also
be used to set the input name.
Example
Command/response sequence for setting the current input to “BDP300”:
Command: 0x21 0x01 0x20 0x06 0x42 0x44 0x50 0x33 0x30 0x30 0x0D
Response: 0x20 0x01 0x20 0x00 0x06 0x42 0x44 0x50 0x33 0x30 0x30 0x0D
FM Scan up/down (0x23)
Initiates a FM scan up or down. Note: only valid if on FM input
Example
Command/response to starting a FM scan up:
Command: 0x21 0x01 0x23 0x01 0x01 0x0D
Response: 0x21 0x01 0x23 0x00 0x01 0xFF 0x0D
Heartbeat (0x25)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x20
Dl
0x01 (query) or <n> (limited to 10 characters) for setting name
Data
F0 - query
1-<n>
Et
0x0D
Example
Command/response to starting a DAB scan:
Command: 0x21 0x01 0x24 0x01 0xF0 0x0D
Response: 0x21 0x01 0x24 0x00 0x01 0xFF 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x25
Dl
0x01
Data
0xF0 - Heartbeat
Et
0x0D
RESPONSE:
Byte:
Description:
Byte:
Description:
St
0x21
St
0x21
Zn
Zone Number
Zn
Zone Number
Cc
0x25
Cc
0x20
Ac
Answer code
Ac
Answer code
Dl
0x01
Dl
Data length - <n> if setting, 0x0A if requesting the name
Data1
0x00 - response
Data1 Data <n>
Input name in ASCII characters
Et
0x0D
Et
0x0D
Reboot (0x26)
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x23
Dl
0x01
Data
0x01 - Scan up
0x02 - Scan down
0x0D
RESPONSE:
Initiates a DAB scan. Note: only valid if on DAB input
Example
Command/response to sending a heartbeat command:
Command: 0x21 0x01 0x25 0x01 0xF0 0x0D
Response: 0x21 0x01 0x25 0x00 0x01 0x00 0x0D
RESPONSE:
Et
DAB Scan (0x24)
Heartbeat command to check unit is still connected and communication - also
resets the EuP standby timer.
Forces a reboot of the unit.
Example
Command/response to sending a reboot command:
Command: 0x21 0x01 0x26 0x06 0x52 0x45 0x42 0x4F 0x4F 0x54 0x0D
Response: 0x21 0x01 0x26 0x01 0x00 0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x26
Dl
0x06
Data1
0x52
Data2
0x45
Data3
0x42
Data4
0x4F
Byte:
Description:
Data5
0x4F
St
0x21
Data6
0x54
Zn
Zone Number
Et
0x0D
Cc
0x23
RESPONSE:
Ac
Answer code
Byte:
Description:
Dl
0x01
St
0x21
Data1
0xFF - scanning
Zn
Zone Number
Et
0x0D
Cc
0x26
Ac
Answer code
Dl
0x01
Data1
0x00 - response
Et
0x0D
COMMAND:
Byte:
Description:
St
0x21
Zn
0x01
Cc
0x24
Dl
0x01
Data
0xF0 - Start DAB scan
Et
0x0D
RESPONSE:
28
Byte:
Description:
St
0x21
Zn
Zone Number
Cc
0x24
Ac
Answer code
Dl
0x01
Data1
0xFF - scanning
Et
0x0D
29
AVR380/450/750 RC5 command codes
These codes are recognised as infra-red signals received by the front panel,
RC5 electrical signals received by the remote in jacks and as control data using
the ‘Simulate RC5 IR Command’ (0x 08).
Basic Functions
Advanced Functions
These RC5 codes are not present on the supplied remote control but have been
created for custom install use. In order for the AVR380/450/750 to respond to
these codes they must be transmitted from a programmable IR remote control
or over the control link using the ‘Simulate RC5 IR Command’ (0x08).
These RC5 codes are present on the supplied IR remote control and provide
control over basic amplifier and video processing functions.
Function
RC5 code
[systemcommand]
RC5 code
(Data1 - Data2)
Decimal
Hexadecimal
Standby
16-12*
0x10 - 0x0C*
Select STB
16-1
0x10 - 0x01
Select AV
16-2
0x10 - 0x02
Select Tuner
16-3
0x10 - 0x03
Select BD
16-4
0x10 - 0x04
Select Game
16-5
0x10 - 0x05
Select VCR
16-6
0x10 - 0x06
Select CD
16-7
0x10 - 0x07
Select Aux
16-8
0x10 - 0x08
Select Audio Return Channel (Display)
16-9
0x10 - 0x09
Select SAT
16-0
0x10 - 0x00
Select PVR
16-34
0x10 - 0x22
Select USB
16-18
0x10 - 0x12
Select NET
16-11
0x10 - 0x0B
Navigate Up
16-86
0x10 - 0x56
Navigate Left
16-81
0x10 - 0x51
OK
16-87
0x10 - 0x57
Navigate Right
16-80
0x10 - 0x50
Navigate Down
16-85
0x10 - 0x55
Cycle between decoding modes (MODE)
16-32
0x10 - 0x20
Enter system menu (MENU)
16-82
0x10 - 0x52
Mute
16-13
0x10 - 0x0D
Change VFD brightness (DISP)
16-59
0x10 - 0x3B
Decrease volume (-)
16-17
0x10 - 0x11
Increase volume (+)
16-16
0x10 - 0x10
Activate DIRECT mode
16-10
0x10 - 0x0A
Room EQ on/off / NET “Now Playing” screen /
iPod Play/Pause
16-30
0x10 - 0x1E
Random
Repeat
Direct mode On
Direct mode Off
RC5 Code
[system-command]
RC5 Code
(Data1 - Data2)
Decimal
Hexadecimal
16 - 48
0x10 - 0x30
16 - 49
16-78
16-79
0x10 - 0x31
0x10 - 0x4E
0x10 - 0x4F
Dolby PL II / IIx Game
16-102
0x10 - 0x66
Dolby PL II / IIx Movie
16-103
0x10 - 0x67
Dolby PL II / IIx Music
Multi Channel
Stereo
Dolby PL
16-104
16-106
16-107
16-110
0x10 - 0x68
0x10 - 0x6A
0x10 - 0x6B
0x10 - 0x6E
DTS Neo:6 Cinema
16-111
0x10 - 0x6F
DTS Neo:6 Music
16-112
0x10 - 0x70
5/7 Ch Stereo
Dolby D EX
Mute On
16-69
16-118
16-119
0x10 - 0x45
0x10 - 0x76
0x10 - 0x77
Mute Off
16-120
0x10 - 0x78
NET
16-53
0x10 - 0x35
FM
DAB (AVR450/750 only)
Video STB-CVBS
16-54
16-72
16-58
0x10 - 0x36
0x10 - 0x48
0x10 - 0x3A
Video PVR-CVBS
16-60
0x10 - 0x3C
Video BD-CVBS
16-62
0x10 - 0x3E
Video Game-CVBS
Video AV-Component
Video SAT-Component
Video BD-Component
16-71
16-83
16-88
16-89
0x10 - 0x47
0x10 - 0x53
0x10 - 0x58
0x10 - 0x59
Video VCR-HDMI
16-90
0x10 - 0x5A
Video AV-HDMI
16-91
0x10 - 0x5B
Toggle Dolby Volume on/off
/ NET & iPod Play/Pause
16-70
0x10 - 0x46
Video PVR-HDMI
Access Bass control
16-39
0x10 - 0x27
Video SAT-HDMI
Access Speaker Trim controls
16-37
0x10 - 0x25
Video BD-HDMI
Access Lipsync Delay control / NET & iPod Stop
16-50
0x10 - 0x32
Video GAME-HDMI
16-67
0x10 - 0x43
Access Subwoofer Trim control
16-51
0x10 - 0x33
Video STB- HDMI
16-68
0x10 - 0x44
Access Treble control
16-14
0x10 - 0x0E
Lip Sync +5ms
FAV+
16-41
0x10 - 0x29
Lip sync -5ms
16-101
0x10 - 0x65
FAV-
16-42
0x10 - 0x2A
Sub trim +0.5dB
16-105
0x10 - 0x69
16-108
0x10 - 0x6C
16-92
16-93
16-94
16-100
0x10 - 0x5C
0x10 - 0x5D
0x10 - 0x5E
0x10 - 0x64
HOME
16-43
0x10 - 0x2B
Sub trim -0.5dB
Cycle between VFD information panels
16-55
0x10 - 0x37
Dolby PLII/x Music Centre +1
16-109
0x10 - 0x6D
Change control to next zone
16-95
0x10 - 0x5F
Dolby PLII/x Music Centre -1
16-113
0x10 - 0x71
Set selected zone to Follow Zone 1
16-20
0x10 - 0x14
Dolby PLII/x Music Dim. +1
16-114
0x10 - 0x72
Cycle between output resolutons
16-47
0x10 - 0x2F
Dolby PLII/x Music Dim. -1
16-115
0x10 - 0x73
0x10 - 0x7B*
Dolby PLII/x Panorama On
16-116
0x10 - 0x74
0x10 - 0x7C*
Dolby PLII/x Panorama Off
16-117
0x10 - 0x75
Video out Preferred/Best
16-125
0x10 - 0x7D
Video out SD Prog
16-15
0x10 - 0x0F
Video out 720p
16-23
0x10 - 0x17
Video out 1080i
16-26
0x10 - 0x1A
Video out 1080p
16-27
0x10 - 0x1B
Video out 4k
16-76
0x10 - 4C
Video out Bypass
16-28
0x10 - 0x1C
Power On
Power Off
* Note - commands not supported over IP control
30
Function
16-123*
16-124*
Function
RC5 Code
[system-command]
RC5 Code
(Data1 - Data2)
Decimal
Hexadecimal
Frame Rate Auto
16-63
0x10 - 0x3F
Frame Rate 50
16-64
0x10 - 0x40
Frame Rate 60
16-65
0x10 - 0x41
Frame Rate ‘Follow Input’
16-66
0x10 - 0x42
Display Off
16-31
0x10 - 0x1F
Display L1
16-33
0x10 - 0x21
Display L2
16-35
0x10 - 0x23
Balance left
16-38
0x10 - 0x26
Balance right
16-40
0x10 - 0x28
Bass +1
16-44
0x10 - 0x2C
Bass -1
16-45
0x10 - 0x2D
Treble +1
16-46
0x10 - 0x2E
Treble -1
16-98
0x10 - 0x62
Zone
16-95
0x10 - 0x5F
Zone 2 Power On
23-123
0X17 - 0x7B
Zone 2 Power Off
23-124
0x17 - 0x7C
Zone 2 Vol+
23-1
0x17 - 0x01
Zone 2 Vol-
23-2
0x17 - 0x02
Zone 2 Mute
23-3
0x17 - 0x03
Zone 2 Mute On
23-4
0x17 - 0x04
Zone 2 Mute Off
23-5
0x17 - 0x05
Zone 2 CD
23-6
0x17 - 0x06
Zone 2 BD
23-7
0x17 - 0x07
Zone 2 STB
23-8
0x17 - 0x08
Zone 2 AV
23-9
0x17 - 0x09
Zone 2 Game
23-11
0x17 - 0x0B
Zone 2 Aux
23-13
0x17 - 0x0D
Zone 2 PVR
23-15
0x17 - 0x0F
Zone 2 FM
23-14
0x17 - 0x0E
Zone 2 DAB (AVR450/750 only)
23-16
0x17 - 0x10
Zone 2 USB
23-18
0x17 - 0x12
Zone 2 NET
23-19
0x17 - 0x13
Select HDMI Out 1
16-73
0x10 - 0x49
Select HDMI Out 2
16-74
0x10 - 0x4A
Select HDMI Out 1 & 2
16-75
0x10 - 0x4B
31
23425
SH256E Issue 3
32
WATERBEACH, CAMBRIDGE CB25 9QE, England
+44 (0)1223 203200
http://www.arcam.co.uk/extranet
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement