Signamax
Connectivity Systems
Dual Rate SFP
Converter Series
U
S E R
’
S
G
U I D E
Signamax
Connectivity Systems
Dual Rate SFP
Converter Series
User’s Guide
Signamax
Dual Rate SFP Media Converter
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Signamax
Connectivity Systems from Advanced Electronic
Supports Products Inc. All rights reserved. All brand names are registered trademarks of their relative holders.
Trademarks
Product names mentioned in this manual may be trademarks or registered trademarks of those products and are hereby acknowledged.
•
Ethernet is a trademark of Xerox Corporation.
•
Microsoft Windows is a trademark of Microsoft Corporation.
•
Signamax
is a trademark of Advanced Electronic Support Products,
Inc.
User’s Manual 1
Signamax
Dual Rate SFP Media Converter
Preface
This manual describes how to install and use the Signamax
Dual Rate SFP Media Converter. The Signamax
Dual Rate
SFP Media Converter introduced here provides one channel media conversion solution:
10/100/1000BaseTX to 100Base and 1000Base dual rate
SFP fiber interface with Link Fault Signaling function
The Signamax
Dual Rate SFP Media Converter fully complies with IEEE802.3 10BaseT, IEEE802.3u
100BaseTX/FX, IEEE802.3ab 1000BaseT, and IEEE802.3z
1000BaseSX/LX Ethernet standards.
In this manual, you will find:
•
Product overview
•
Features on the media converter
•
Illustrative LED functions
•
Installation instructions
•
Specifications
2 User’s Manual
Signamax
Dual Rate SFP Media Converter
Table of Contents
FCC W ARNING ............................................................. 1
CE M ARK W ARNING ..................................................... 1
T RADEMARKS ............................................................... 1
P REFACE ....................................................................... 2
T ABLE OF C ONTENTS .................................................... 3
I NTRODUCTION ............................................................. 4
P RODUCT O VERVIEW .......................................... 4
P RODUCT F EATURES .......................................... 5
P ACKING L IST .................................................... 5
O NE -C HANNEL M EDIA C ONVERTER .............................. 7
P ORTS ............................................................... 7
F
RONT
P
ANEL
& LED
S
....................................... 7
I NSTALLATION .............................................................. 8
S ELECTING A S ITE FOR THE E QUIPMENT ............... 8
C ONNECTING TO P OWER ..................................... 8
I
NSTALLING IN A
C
HASSIS
.................................... 9
S PECIFICATIONS ............................................................ 9
C ONTACT I NFORMATION ............................................. 10
User’s Manual 3
Signamax
Dual Rate SFP Media Converter
Introduction
The Dual Rate SFP Media Converter provides one channel for media conversion between 10/100/1000BaseTX to
100Base and 1000Base dual rate SFP fiber interface with
Link Fault Signaling function. It can be used as a stand-alone device or with a standard 19” chassis as shown below.
Product Overview
<NOTE> The chassis is to be ordered separately.
4 User’s Manual
Signamax
Dual Rate SFP Media Converter
Product Features
•
Complies with IEEE802.3 10BaseT, IEEE802.3u 100BaseTX/FX,
IEEE802.3ab 1000BaseT, and IEEE802.3z 1000BaseSX/LX.
•
Supports IEEE802.3x Flow control: Flow control for Full-duplex and
Back pressure for Half-duplex.
•
SFP fiber interface supports 100Base and 1000Base dual rate fiber transmission.
•
DIP switch configuration for “Link Fault Signaling”.
•
Gigabit transmission supports 9K Bytes jumbo frame.
•
1000Mbps-Auto/Full-duplex, 10/100Mbps-Full/Half-duplex, Auto-
Negotiation, Auto-MDI/MDIX.
•
Full wire-speed forwarding rate.
•
Operating voltage and Max. current consumption: 0.23A @ 12VDC.
Power consumption: 2.76W Max.
•
Power Supply: 12VDC external universal PSU.
•
32℉ to 122℉ (0℃ to 50℃) operating temperature range.
•
Aluminum case.
•
Supports Wall Mounting installation or use with media converter chassis system.
DIP Switch
No. Down
1
2
3
Disable LFS
Enable Auto-Negotiation for TX port
TX port Force mode: Full-duplex
Up
Enable LFS
Enable Force mode for TX port
TX port Force mode: Half-duplex
4
5
TX port Force mode: 100Mbps
SFP at 100Mbps
TX port Force mode: 10Mbps
SFP at 1000Mbps
6 Function reserved Function reserved
<Note> LFS: Link Fault Signaling function. Power must be off/on after resetting LFS function.
Packing List
When you unpack this product package, you will find the items listed below.
Please inspect the contents, and report any apparent damage or missing items immediately to our authorized reseller.
User’s Manual 5
Signamax
Dual Rate SFP Media Converter
•
The Media Converter
•
User’s Manual
•
AC to DC Power Adaptor
6 User’s Manual
Signamax
Dual Rate SFP Media Converter
One-Channel Media Converter
Ports
This converter provides one TX port and one 100Base and
1000Base dual rate SFP socket. For the 100Base and
1000Base dual rate SFP socket, it provides options of multimode/single-mode or WDM multi-mode/single-mode fiber.
For the TX port, it uses RJ-45 connector and supports auto
MDIX for uplink purpose.
Front Panel & LEDs
LED Indicators
The LED indicators give you instant feedback on status of the converter:
LEDs
PWR
LFS
LNKC
G:GE
A:100
LNKF
GE
State Indication
Steady
Off
Power on
PWR stands for POWER
Power off
Steady LFS function enabled
Off
Steady
Off
LFS function disabled
Copper port: A valid network connection established
LNKC stands for LINK/Copper
No connection
Steady
Off
Steady
Green: Connection at the speed of 1000Mbps
Amber: Connection at the speed of 100Mbps
Connection at the speed of 10Mbps
Fiber port: A valid network connection established
LNKF stands for LINK/Fiber
Off No connection
Steady Force fiber port to 1000Base
Off Force fiber port to 100Base
User’s Manual 7
Signamax
Dual Rate SFP Media Converter
Installation
This chapter gives step-by-step installation instructions for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements:
•
The ambient temperature should be between 32 and 122 degrees
Fahrenheit (0 to 50 degrees Celsius).
•
The relative humidity should be less than 95 percent, non-condensing.
•
Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
•
Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the equipment.
•
The power outlet should be within 1.8 meters of the product.
Connecting to Power
• This Converter is a plug-and-play device.
• Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the converter, and then attach the plug into a standard AC outlet with a voltage range from 100 to 240VAC.
8 User’s Manual
Signamax
Dual Rate SFP Media Converter
Installing in a Chassis
The Converter can be fit into any of the expansion slots on a special designed chassis.
•
First, install the converter onto a carrier supplied with the chassis:
Step 1- Unscrew the carrier from the desired expansion slot on the chassis.
Step 2- Fit the converter onto the carrier.
•
When the converter is completely seated onto the carrier, insert the carrier to the guide rails of the expansion slot.
•
Carefully slide in the carrier until it is fully and firmly fit the chassis.
Fasten the screws onto the carrier.
<NOTE> Never insert any converter into the chassis directly without using the supplied carriers. The carriers allow secure and consistent placement of the converters into the chassis’ backplane without causing any damage.
Specifications
Applicable Standards
Fixed Ports
Speed
10BaseT
100BaseTX/FX
1000BaseT
1000BaseSX/LX
Forwarding rate
LED Indicators
IEEE802.3 10BaseT
IEEE802.3u 100BaseTX/FX
IEEE802.3ab 1000BaseT
IEEE802.3z 1000BaseSX/LX
1 10/100/1000BaseTX port
1 100Base and 1000Base dual rate SFP fiber interface
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
2000Mbps for full-duplex
2000Mbps for full-duplex
14,880pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
PWR, LFS, LNKC, Copper Port Speed,
LNKF, SFP Port Speed
Dimensions 3.16” (W) x 4.3” (D) x 0.94” (H)
(80.3mm (W) × 109.2mm (D) × 23.8mm (H))
0.33lb. (150g) Weight
Power
Power Consumption
External power adaptor 12VDC, 0.23A
2.76W Max.
Operating Temperature 32℉ ~ 122℉ (0℃ ~ 50℃)
Storage Temperature
Humidity
Emissions
14℉ ~ 158℉ (-10℃ ~ 70℃)
5 ~ 95%, non-condensing
FCC part 15 Class A, CE Mark Class A
User’s Manual 9
Signamax
Dual Rate SFP Media Converter
Contact Information
SIGNAMAX
CONNECTIVITY SYSTEMS
An AESP Company
16295 N.W. 13h Avenue
Miami, Florida 33169, U.S.A.
Phone: 305-944-7710 Fax: 305-949-4483
Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201
Http://www.signamax.com
E-mail: [email protected]
10 User’s Manual