1028 STREET ROAD, P.O. BOX 38
PHONE # 215-357-5110
LITTLE WONDER.
DIVISION OF SCHILLER-PFEIFFER, INCORPORATED
SOUTHAMPTON, PA 18966
FAX # 215-357-8045
OPERATING, ASSEMBLY INSTRUCTIONS, AND PARTS LIST FOR
LITTLE WONDERBLOWERS
CAT. Nos. 9005S, 9005P, 9005PI/C, 9008P, 9008PI/C, 9111P, 9111PI/C, 9009H,9009VG
AW arn i n g . Theengineexhaustfromthisproductcontains chemicals knownto the
" State of Californiato cause cancer, birth defects or otherreproductive harm.
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS. |
2. DRESS PROPERLY — Do not wear loose clothing or jewelry.
They can be caught in moving parts. Use of sturdy gloves,
non-skid footwear and safety glasses recommended. Always
wear ear protectors where possible. Use face filter to avoid
breathing dust.
3. STAY ALERT — Watch what you are doing and use common
sense. Do not operate blower when fatigued.
4 À DANGER ROTATING FAN — KEEP HANDS AWAY
FROM AIR INTAKE AND AIR OUTLET CHUTE — Keep both
hands on handles when power is on. Do not attempt to
_ remove material when blower is running.
5. À DANGER — DO NOT INSTALL OR REMOVE
ATTACHMENTS WHILE BLOWER IS RUNNING. Turn off
engine to make changeover. Be sure throttle is in the stop
position, and the blower has come to a complete stop.
Remove the spark plug wire before removing material.
6. A WARNING — KEEP CHILDREN AND INCAPABLE
PERSONS AWAY — Do not permit children to contact
biower. Keep children a safe distance from work area. Never
allow a person mentally ill, under influence of alcoholic drinks
or drugs, or toc young in age, to operate the blower.
7. DO NOT POINT THE BLOWER OUTLET inthe direction of
people, cars, glass, or other similar items which could be injured
or damaged by blown debris.
8. DON'T OVERREACH OR STAND ON UNSTABLE
SUPPORT. — Keep good footing and balance at all times.
9. HANDLE GASOLINE WITH CARE. IT IS HIGHLY
FLAMMABLE. Refuel before starting work. Do not smoke
while handing fuel. Do not refuel a hot or running engine.
Avoid spilling fuel or oil. Always wipe unit dry before using.
Move at least 10 feet away from the fueling point before
starting engine. Always store gasoline in an approved con-
tainer. Fill tank outdoors with extreme care — never fill
indoors. Replace gasoline cap securely. If fuel is spilied
move blower and fuel container from area and do not create
‚ .a source of ignition.
10. CAUTION - Do not start or run engine indoors as poisonous
\ carbon monoxide is emitted. Do not operate in un-ventilated
area.
11. MULTIPLE OPERATORS — Keep a safe distance between
two or more operators when working together simultaneously.
12. DO NOT USE the blower when electric system causes spark
outside the cylinder. Check spark plug from time to time.
When checking, keep plug a safe distance from cylinder to
avoid buming of evaporated fuel rom cylinder.
13. MAINTAIN AND EXAMINE BLOWER WITH CARE —
Follow maintenance instructions given in manual. Do not
use the blower if the muffler is defective or missing.
14. STORE BLOWER INDOORS -Whennotinuse, store blower
indoors in a sheltered area (a dry place) where not accessible to
children, The blower, as well as fuel, should not be stored in a
house. Keep throttle in stop position.
15. DO NOT ATTEMPT TO REPAIR BLOWER —— Have repairs
made by qualified dealer or repairman. See that only Little
Wonder replacement parts are used.
16. BE SURE BLOWER IS FULLY ASSEMBLED -— Never
operate blower without all guards and deflectors in place.
Ensure that all nuts, bolts, screws are installed and property
tightened.
17. ALWAYS KEEP THE THROTTLE IN THE “STOP”
POSITION WHEN NOT IN USE.
WARNING! INORDERTO AVOID ENGINE DAMAGE
DUETO OVER-HEATING OR OVER-REVVING, KEEP
ENGINE RECOIL STARTER ASSEMBLY, THE BLOWER
INTAKE AND OUTLET AREAS, OR HOSE ACCESSORIES
CLEAR AND FREE OF LEAVESOR OTHER DEBRIS.
19. A WARNING — Fan coasts after tum off.
20. Never operate blower without all guards and legible waming
labels in place. Replace ali labels should they become
damaged or are illegible.
ASSEMBLY INSTRUCTIONS: (5,8,9HP)
* NOTE: Numbers in brackets (-) represent key Numbers shown
on Parts List, and parts explosion. |
A. install lower handles (41) on top of deck (2 places). Secure with
four cap screws (47) four nuts (33) and four silver washers (18)
( finger tight).
В. Install upper handle (37) with four cap screws (47), four nuts (33)
and gold washers (56). Secure all nuts and bolts with wrench.
Do not tighten bolts until ай handles are in place.
C. Attach throttle with cap screw (36) and nut (34) thru hole on either
right or left side of upper handles (37), and connect throttie cable
clip (39) to upper handles (37).
D. Tilt machine back on handie and install front wheel housing (6)
to three studs on lower front of blower housing. Secure with three
nuts (4).
E. insert axle sleeve (8) in wheel (7) and install on front wheel
housing (6) with axie bolt (5), secure with axle nut (9).
PARTSLIST
When orderingreplacementparts, specify by PARTNUMBER. Do not order by Key numberor Assembly number.
Key Part — Quantity per unit for each Blower catalog number.
Number Number Description 9005S 9005P 9005PIC 9008P 9008PIC 9009H 9009VG
954-1 intake Guard Assembly
929-1 Cover Piate
907 Fan Assembly 5 H.P.
—t
alll
a | — —
1
2
3
3 913 Fan Assembly 8 H.P.
4 114B Flange Nut 5/16 - 18
5 102A Bolt 3/8 - 16 x 3" long
6 944 Wheel Housing
7 106 8" symmetrical Wheel
8 102C Axle Sleeve
9 1028 Lock Nui 3/8 - 16
10 970 Deflector Handle
17 966 Deflector
12 329 Bolt 10-32 x 5/8
13 973 Lock Nut 10-32
14 8-18 Grip Ring
15 962 Spring
16 967 Index Side Lock Bushing
17 5924 Hitch Pin Clip
18 163 Washer - Flat 3/8
19 170 Clevis Pin
936 Side Defiector 5 HP.
937 Side Deflector 8 HP.
963 External Tooth Lock Washer
154 Knob
902 Blower Housing 5 H.P.
905 Blower Housing 8 H.P.
900 Deck 5 H.P.
901 Deck 8 H.P.
901-11VH Deck 9H.P.
939 Boli Grade 5, 3/8-24 N.F. x 1 1/4" Ig.
938 Bol Grade 5, 7/16-20 N.F. x 1 1/2" 19.
941 Lock Washer - Spit 3/8
940 Lock Washer - Spit 7/16
950 Washer 1" O.D. x 7/161.D. x 3/16 THK
951 internal & External - Lockwasher
915 Key For Fan 1/4 x 1/4x 7 ig.
920 Key For Fan 1/4 x 1/4 x 1 1/7 lg.
927 intake Guard - Clamp
968 Bracket Eng. To Housing 5 H.P.
969 Bracket Eng. To Housing 8 H.P.
955 Bracket Eng. To Housing Honda
956 Bracket Eng. To Housing Vanguard
Lock Nut 5/16-18
972 Lock Nut 1/4-20
943 Throttle
945 Throttle
378 Hex Head Cap Screw 1/4-20 1 1/2
917-
113
946
——
—
O
1 Upper Handle
Hex Hood Screw 5/16-18 x 1 1/2"
Throttle Clip
405-1 Washer - Light 5/8 1.D.
SER GERBBR EBLUL ОВО КОСО НОО ЧЕСНОКОВ
932-1 Axle
932-2 Axle
1290 Lockwasher 5/1
942 Hex aad Con Screw 5/16-18 13/4"
930 Engine 9 H.P. Honda
931 Engine 9 H.P. Vanguard
947 Engine 5 H.P. Briggs E Stration
9247-16 Engine 5 H.P.I.C. Briggs € Straiton
948 Engine 8 H.P. Briggs & Stration
948-1C Engine 8 H.P.1.C. Briggs & Stratton
985-1 Label 90055
985-2 Label 9005P
985-3 Label 9008P
985-7 Label 9008 PIC
985-8 Label 9005 PIC
974 Label 9009H
975 Label 9009 VS
961 Label Waming
Label Waming
4036 Ear and Eye Label
8-57 Bol 3/8 - 16x 1"
701700 Bolt 5/16 - 18 x 1”
941 Lock Washer Spiß 3/8"
129D Lock Washer 5/16”
900503 5/16 x .030 Yellow Plated Washer
900502 10-32 x 5 1/4 Bolt
in 00 1 . o adri $ KV EAN a Hs 1 in 8 ND ND NS ts ОО nnd mat und | mi Na | und und wat § and | nd | 1 und $ met and md Y tt UY ot nt nt rt ON ND tot ot ot and mt et BD 4 a
MO: 5 0 à mé amas à 4 8 1 1 = 1 0 6° 0 = à ВЫ Вы (с m № в № № == =её ОО ой ta al | A DANNA Na | md § wd | EA Aa A NP A HN a A
En 0 à NN ala 1 1 00 0 4° 6 ево В 5 р = 1 №) | № № 0 st O3 ll and ar | A ZN $ mo Y el med | mtb ett et) td UY et mt ot ot ON) ot ot nt а mt md mt BD ed um
in 5 1 6 NN a EN AA ОО = BAYT RIAD ed md Pd nt mt | mt NDF bed E6 | awd ood eed md | Y E A Ja ll ON mt ой ей я д а о В неа — —
E 0 : N 6 NS soni o Y a à U 8 0 0 0 8 8 ‘ 4 — 00 Ha 1 = о) К) | № № tet Pis E NN | al and | e | E A 1 A ON ND 0 nd a an оо а о В ой 4 —t
in O0 NS 4 ND 1024 mé mé ей 5 3 5 1 A A TU в = 1 O MI ns à NS | AND AS nt md Py md ный oat Y NN nt it | und ad ad | E Y a LANA GE a О\ № e Y
RELLENE LES
in 00 € 6 1 — NN ll COMA 1 NINN Pa Y MD 6 Nella e Y E a Y Y NO a E Y =
BLOWER CATALOG #3009H, S008VG
wd
Ww №
6 94 0 bun à
— PARTS LIST —
When ordering replacementparts, specify by PART NUMBER. Donotorder by Key number.
—— Quantity per unit for each Blower catalog num)
Key Part
Number Number Description 9111P 9111P/C |
1 954-1 Intake Guard ] 1
2 929-1 Front Panel 1 ]
3 900200 11 H.P. Fan Assembly ] ]
4 114B Fiange Nut 5/16-18 20 20
5 900501 Front Axle Bolt 3/8-16 x $ 1/4 1 ]
6 900401 Wheel Housing 1 ]
7 934 10" Symmetrical Wheel (Front) 1 1
8 900404 Front Wheel Sleeve 1 1
9 1028 Lock Nut 3/8-16 1 1
10 970 Deflector Handle 1 1
11 900101 11 H.P. Deflector 1 1
12 329 Bolt 10-32 x 5/8 2 2
13 973 Lock Nut 10-32 8 8
14 &-18 Grip Ring 1 1
15 952 Spring ] 1
16 967 index Slide Lock Bushing 1 1
17 924 Hitch Pin 1 ]
18 163 Fiat Washer 3/8 5 5
19 170 Clevis Pin 1 1
20 900102 Side Deflector 11H.P. 1 1
21 963 External Tooth Lock Washer 1 1
22 154 Knob 1 1
23 900000 Blower Housing 11 H.P. 1 1
24 901-11 Deck 11 H.P. ] 1
25 938 Bolt Grade 5 7/16-20 N.F. x 1 3/4 1 1
26 940 Lock Washer 7/16 - Split 1 1
27 950 Heavy Washer ] ]
28 951 Intemal/External Lock Washer 1 ]
29 915 Machine Key ] 1
31 927 Intake Guard Ciamp ] 1
32 969-11 Bracket Engine to Housing 1 1
33 114C Nylon Lock Nut 5/16-18 9 9
34 972 Lock Nut 1/4-20 1 1
35 900901 Throttie Control ] 1
36 378 Hex Head Cap Screw 1/4-20 x1 1/2 1 1
37/40 200300 Upper Handle with Grips 1 1
37 900301 Upper Handie 1 1
38 113 Hex Head Screw 5/16-18x1 1/2 4 4
39 946 Throttle Clip 1 1
40 900302 Grip Set 1 1
41 916-2 Lower Handle 2- 2
42 312 Retaining Rings 2 2
43 934-1 10" Offset Wheels (Rear) 2 2
45 932-1 Axle ] 1
46 129D Lock Washer 5/16 4 4
47 942 Hex Head Cap Screw 5/16-18 x 1 3/4 8 8
945-11 Engine 11 H.P. 1 -
948-11/C Engine 11 H.P. 1/C - 1
50 900601 Biower Model Label 9111P ] -
50 900602 Blower Model Label ?111PIC - 1
51 961 Label Waming 1 1
52 683 Label Waming 1 1
53 4036 Decibel Warning Labei 1 1
54 900405 Front Wheel Bracket Spacer 2 2
56 900503 5/16 Washers (Yellow Plated) 8 8
57 900502 10-32 x 5 1/4 Bolts 6 6
1028 Street Road « P.O. Box 38 » Southampton, PA 18966 « (215) 357-5110. Fax: (215) 357-8045
®
Little Wonder
BLOWER CATALOG #9111P and 9111PI1/C
ASSEMBLY INSTRUCTIONS FOR THE 9111P and 9111PI/C
NOTE: Numbers in brackets (-) represent key Numbers shown on Parts List, and parts explosion in the manual.
A. Install lower handles (41) on top of deck (2 places). Secure, finger tight, with four cap screws (47),
four silver washers (18) and four lock nuts (33).
B. Install upper handle (37) with four cap screws (38), eight yellow plated washers (56) and four lock
nuts (33). Tighten lower handle nuts and bolts. Tighten upper handle nuts and bolts until the lower
handle tubing pinches the upper handle. it will be normal for the lower handle to crush slightly.
C. Attach throttie with cap screw (36) and nut (34) thru hole on either right or left side of upper handles
(37), and connect throttle clip (39) to upper handies (37).
D. Tilt blower back on handle and install front wheel housing (6) to three studs on iower front of blower
housing. Secure with three flange nuts (4)
E. Insert axie sleeve (8) in wheel (7) and install on front wheel housing (6) with axle bolt (5), secure with
axle nut (9).
OPERATING INSTRUCTIONS:
Be sure to read the Briggs & Stratton or Honda instruction
manual packed with your unit.
“Do Not Forget To Put Oil In Your Engine"
Your Little Wonder Blower eliminates the drudgery
usually associated with the manual operated tool such as a
rake or broom, and 15 very easy to use.
Leaves, thatch or other debris can be directed into
windrows or piles, by simply maneuvering the unit and
directing the flow of air accordingly.
Air flow can be directed to the side or front by the two-
position deflector, The front discharge position is used to
remove debris from along walls, fences, etc. The side
discharge position is used to form windrows or piles, The
horizontal deflector directs air downward to “chisel® under
wet, heavy leaves and litter. The velocity is regulated by
the throttie control. |
For best performance, be sure engine recoil starter
assembly, the blower intake and outlet areas, or hose
accessories are clear and free of leaves or other debris.
USER MAINTENANCE INSTRUCTIONS:
1. Keep all nuts, bolts, and screws tight.
2. Never store the Blower with fuel in the fuel tank inside a
building where fumes may reach an open flame or
sparks, or in a confined space.
3. Always refer to the instruction manual for important
details if the product is to be stored for an extended
period.
4. CAUTION - After approximately the first three (3) to
four (4) hours of operation, tighten the bolt holding the
fan to a torque of 40 foot pounds or 480 inch pounds.
"LOCTITE" 242 has been used on the engine shaft to
secure the fan on the shaft.
5. Engine - 4 cycle. (Refer to engine manufacturer's
operating instructions for fuel recommendations and
additional information).
Tires - Tubeless. Inflate to air pressure of 30 P.S. 1.
7. Labels should be inspected before each use. Replace
damaged labels immediately.
о
Specification, descriptions, and illustrative material in the literature are as accurate as shown at the time of publication, but are subjected to change without notice.
DIRECTIONS FOR FAN REMOVAL:
(This procedure must be done by qualified personnel)
1. Remove all bolts and nuts securing the engine deck
and blower housing. ых
2. Remove intake guard and front panel. O -
3. Remove bolt securing fan to engine crankshaft.
4. The fan has a 3/4-10 nut welded onthe fan hub. :
Insert a 3/4-10 bolt and jack or push the engine off
the fan, In some instances, it may be necessary to
apply heat in area of fan hub as Loctite 242 has been
used to secure the fan engine crankshaft. Be careful
not to overheat.
5. Reassemble with Loctite 242 to unsure a snug fit.
PARTS:
All replacement parts may be ordered thru your local dealer
or distributor. For additional information on obtaining
replacement parts contact:
Little Wonder
1028 Street Road, Southampton, PA 18966
Phone (215) 357-5110 Fax (215) 357-8045
FEATURES:
e 35% greater air power. a
e Smooth-rolling big front wheel for easy operation O
uneven ground.
e Heavy gauge 316" steel plate deck. Blower housing is
12 gauge steel with arc weided seams. |
e Recoil starter handle in the clear for right or left hand
starting.
e Low-tone muffiers for noise dampening.
e Dual element air cleaner.
e Heavy duty handle with anti-vibration grip.
e 5 year warranty on fan and handle assembly.
e Right or left handed throttle control.
MANY USES:
The extreme versatility offered by Little Wonder's
line of blowers makes them ideally suited for a wide variety
of jobs - blowing leaves, grass clippings, and thatch,
blowing tennis courts dry, cleaning large driveways,
stadiums, parking lots and other hard surfaces, and
precleaning roofs before repair.
mode! blower into an effective vacuum. See back
details.
By simply adding an attachment, you can convert 2.
И
ATTACHMENTS: Due to the adaptability and versatility of the Little Wonder Blower, several options and accessories
are available as illustrated below.
Tm I rs wT Te TN rv pan pe Tees
mr Ny’ Ca 2 EA TOA a АЙ NC aT WEN LN =
E Ya TA и ro т те Mig и
"и pr = Ze
o
Tr.
6” diameter x 10 foot
long intake hose
(Cat. #9015) and 6” (Cat. #9016) 6”
diameter x 20 foot Diameter x 10 foot
long truck loader long intake hose with
hose (Cat. 49022). bagging attachment. e
ACCESSORIES STORAGE AFTER U
CAT + - DESCRIPTION Inspect and adjust every part of the unit.
9015 Standardintake hose (6" |.D.x 10'-0” LG.) with handle — Completely clean every part and repair, if necessary.
and mounting flange. . .
— Apply th t f clean oil on metal parts to
8016 Standard intake hose with bagging attachment. prevent he ing of се ' Р
9018 Heavy duty intake hose with wear strip (6° 1.D. x 10°-0
L.G.) with handle and mounting flange. — Remove hose accessories from blower
9019 Bagging attachment (no hose included). (if applicable).
9022 Loading hose (6° I.D. x 20-0" L.G.). — Place throttle control in the “stop” position.
984 Bag.
For models 9111P & 9111PIC only: Refer to engine manufacturer's "Operating and
Maintenance instructions", for procedures on how to
9116 11 H.P. standard intake hose with bag attachment. .
service and prepare the engine for storage.
8119 11 H.P. bag attachment (no hose).
9122 11 Н.Р. Load hose. Store in a dry area, free from dust.
O LIMITED SERVICE 8: WARRANTY POLICY
All Little Wonder blowers are guaranteed against defects in material and
workmanship for a period of ONE YEAR FROM DATE OF PURCHASE when used for
RESIDENTIAL SERVICE, NINETY DAYS FROM DATE OF PURCHASE for
COMMERCIAL SERVICE. Fan and handle assembly on blowers are warranted
separately for A FIVE YEAR PERIOD FROM DATE OF PURCHASE for Residential
and Commercial use. Models 9111P and 9111PIC have a five year warranty on the
entire unit (except the engine). Any Little Wonder product or part found to
be defective within the warranty period are to be retumed to your local authorized
Little Wonder dealer.
Transportation charges on parts and units submitted for replacement under this
warranty must be borne by purchaser.
Engines or gas powered blowers are warranted separately by the engine
manufacturer. Therefore, there are no warranties made, expressed or implied, for
engines of gas powered blowers by Little Wonder made for engines used on
Little Wander blowers.
THIS WARRANTY shall not be effective if the product has been the subject of
misuse, negligence or accident, or, if the product has been repaired or altered by
anyone other than your local authorized Little Wonder dealer in any respect
which affects its condition or operation.
Little Wonder shall not be liable for any special indirect or
consequential damages arising from defective equipment. Any implied
warranty, including merchantability or fithess for a particular purpose,
shall not extend beyond the written period.
THIS WARRANTY shall only be effective if the enclosed warranty card is
properly filled out and retumed to Little Wonder, Division of Schiller-Pfeiffer,
Inc., 1028 Street Road, Southampton, PA 18966 at time of purchase.
AWarning
s Theengineexhaustfromthis product contains chemicals knowntothe
”
" State of Californiato cause cancer, birth defects or other reproductive harm.
P/N978-6 (1/96)
">
