UA-25EX Manual

UA-25EX Manual
UA-25EX_e.book 1 ページ 2008年3月31日 月曜日 午後2時12分
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (p. 2; p. 4). These sections provide important information concerning the
proper operation of the unit. Additionally, in order to feel assured that you have gained a good
grasp of every feature provided by your new unit, Owner’s manual should be read in its
entirety. The manual should be saved and kept on hand as a convenient reference.
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced
in any form without the written permission of ROLAND CORPORATION.
UA-25EX_e.book 2 ページ 2008年3月31日 月曜日 午後2時12分
USING THE UNIT SAFELY
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
• Do not open or perform any internal
modifications on the unit.
...............................................................................
• Do not attempt to repair the unit, or
replace parts within it (except when this
manual provides specific instructions
directing you to do so). Refer all
servicing to your retailer, the nearest
EDIROL/Roland Service Center, or an
authorized EDIROL/Roland distributor,
as listed on the “Information” page.
...............................................................................
• Never install the unit in any of the
following locations.
• Subject to temperature extremes
(e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top
of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on
wet floors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration
and shakiness.
...............................................................................
2
The
symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle.
In the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
• Make sure you always have the unit
placed so it is level and sure to remain
stable. Never place it on stands that
could wobble, or on inclined surfaces.
...............................................................................
• This unit, either alone or in combination
with an amplifier and headphones or
speakers, may be capable of
producing sound levels that could
cause permanent hearing loss. Do not
operate for a long period of time at a
high volume level, or at a level that is
uncomfortable. If you experience any
hearing loss or ringing in the ears, you
should immediately stop using the unit,
and consult an audiologist.
...............................................................................
• Do not allow any objects (e.g.,
flammable material, coins, pins); or
liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
...............................................................................
UA-25EX_e.book 3 ページ 2008年3月31日 月曜日 午後2時12分
• Immediately turn the power off, and
request servicing by your retailer, the
nearest EDIROL/Roland Service
Center, or an authorized EDIROL/
Roland distributor, as listed on the
“Information” page when:
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid
has been spilled onto the unit; or
• The unit has been exposed to rain
(or otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked
change in performance.
• Try to prevent cords and cables from
becoming entangled. Also, all cords
and cables should be placed so they
are out of the reach of children.
...............................................................................
• Never climb on top of, nor place heavy
objects on the unit.
...............................................................................
• Disconnect all cords coming from
external devices before moving the
unit.
...............................................................................
...............................................................................
• In households with small children, an
adult should provide supervision until
the child is capable of following all the
rules essential for the safe operation of
the unit.
• Always turn the phantom power off
when connecting any device other than
condenser microphones that require
phantom power. You risk causing
damage if you mistakenly supply
phantom power to dynamic microphones, audio playback devices, or
other devices that don’t require such
power. Be sure to check the specifications of any microphone you intend to
use by referring to the manual that
came with it.
...............................................................................
• Protect the unit from strong impact.
(Do not drop it!)
...............................................................................
• DO NOT play a CD-ROM disc on a
conventional audio CD player. The
resulting sound may be of a level that
could cause permanent hearing loss.
Damage to speakers or other system
components may result.
(This instrument’s phantom power:
48 V DC, 8 mA Max)
...............................................................................
...............................................................................
3
UA-25EX_e.book 4 ページ 2008年3月31日 月曜日 午後2時12分
IMPORTANT NOTES
Power Supply
Maintenance
• Before connecting this unit to other devices,
turn off the power to all units. This will help
prevent malfunctions and/or damage to
speakers or other devices.
• For everyday cleaning wipe the unit with a soft,
dry cloth or one that has been slightly
dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild, nonabrasive detergent. Afterwards, be sure to
wipe the unit thoroughly with a soft, dry cloth.
Placement
• Using the unit near power amplifiers (or other
equipment containing large power transformers) may induce hum. To alleviate the
problem, change the orientation of this unit; or
move it farther away from the source of interference.
• This device may interfere with radio and
television reception. Do not use this device in
the vicinity of such receivers.
• Noise may be produced if wireless communications devices, such as cell phones, are
operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call,
or while conversing. Should you experience
such problems, you should relocate such
wireless devices so they are at a greater
distance from this unit, or switch them off.
• When moved from one location to another
where the temperature and/or humidity is very
different, water droplets (condensation) may
form inside the unit. Damage or malfunction
may result if you attempt to use the unit in this
condition. Therefore, before using the unit, you
must allow it to stand for several hours, until the
condensation has completely evaporated.
• Depending on the material and temperature of
the surface on which you place the unit, its
rubber feet may discolor or mar the surface.
You can place a piece of felt or cloth under the
rubber feet to prevent this from happening. If
you do so, please make sure that the unit will
not slip or move accidentally.
4
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility of
discoloration and/or deformation.
Handling CD-ROMs
• Avoid touching or scratching the shiny
underside (encoded surface) of the disc.
Damaged or dirty CD-ROM discs may not be
read properly. Keep your discs clean using a
commercially available CD cleaner.
Copyright
• Recording, duplication, distribution, sale,
lease, performance, or broadcast of
copyrighted material (musical works, visual
works, broadcasts, live performances, etc.)
belonging to a third party in part or in whole
without the permission of the copyright owner
is forbidden by law.
• This product can be used to record or duplicate
audio or visual material without being limited
by certain technological copy-protection
measures. This is due to the fact that this
product is intended to be used for the purpose
of producing original music or video material,
and is therefore designed so that material that
does not infringe copyrights belonging to
others (for example, your own original works)
can be recorded or duplicated freely.
• Do not use this unit for purposes that could
infringe on a copyright held by a third party.
We assume no responsibility whatsoever with
regard to any infringements of third-party
copyrights arising through your use of this unit.
UA-25EX_e.book 5 ページ 2008年3月31日 月曜日 午後2時12分
IMPORTANT NOTES
Additional Precautions
• Use a reasonable amount of care when using
the unit’s buttons, sliders, or other controls; and
when using its jacks and connectors. Rough
handling can lead to malfunctions.
• When connecting / disconnecting all cables,
grasp the connector itself—never pull on the
cable. This way you will avoid causing shorts,
or damage to the cable’s internal elements.
• To avoid disturbing your neighbors, try to keep
the unit’s volume at reasonable levels. You may
prefer to use headphones, so you do not need
to be concerned about those around you
(especially when it is late at night).
• When you need to transport the unit, package
it in the box (including padding) that it came
in, if possible. Otherwise, you will need to use
equivalent packaging materials.
* Microsoft, Windows and Windows Vista are
registered trademarks of Microsoft Corporation.
* The screen shots in this document are used in
compliance with the guidelines of the Microsoft
Corporation.
* Windows® is known officially as: “Microsoft®
Windows® operating system.”
* Apple, Macintosh and Mac OS are registered
trademarks of Apple Inc.
* Pentium is a registered trademark of Intel Corporation.
* All product names mentioned in this document
are trademarks or registered trademarks of their
respective owners.
• Some connection cables contain resistors. Do
not use cables that incorporate resistors for
connecting to this unit. The use of such cables
can cause the sound level to be extremely low,
or impossible to hear. For information on cable
specifications, contact the manufacturer of the
cable.
• Before you open the included CD-ROM, you
must read the “license agreement.” Opening
the CD-ROM will be taken to mean your acceptance of the license agreement.
5
UA-25EX_e.book 6 ページ 2008年3月31日 月曜日 午後2時12分
Contents
USING THE UNIT SAFELY.........................................................................2
IMPORTANT NOTES................................................................................4
Contents of the Package..........................................................................7
Panel Descriptions ..................................................................................9
Front Panel .............................................................................................. 9
Rear Panel ............................................................................................ 12
Introduction..........................................................................................14
What is a Driver?................................................................................... 14
Driver Installation and Settings (Windows Vista)......................................... 15
Driver Installation and Settings (Windows XP) ............................................ 18
Driver Installation and Settings (Mac OS X) ............................................... 21
Basic Connections and Settings..............................................................24
Basic Connections.................................................................................. 25
Connecting a Microphone or a Guitar...................................................... 26
Connecting a Microphone and Applying the Compressor ........................... 28
Recording a Digital Signal into Your Computer .......................................... 30
Recording to an MD or Other Digital Device ............................................. 31
Appendix: Driver settings......................................................................32
Adjusting the Latency and Other Settings (Windows) .................................. 32
Adjusting the Latency and Other Settings (Mac OS X)................................. 34
Driver Uninstallation ............................................................................... 35
Appendix: Troubleshooting ...................................................................37
Specifications .......................................................................................46
Index ...................................................................................................48
6
UA-25EX_e.book 7 ページ 2008年3月31日 月曜日 午後2時12分
Contents of the Package
After you open the package, please check that all items are present.
If anything is missing, contact your dealer.
■ UA-25EX
fig.ua-25ex.eps
■ Owner’s manual
This is the document you’re reading. Keep it at hand for reference when needed.
■ CD-ROMs (2 discs)
UA-25EX Driver CD-ROM
This contains the UA-25EX drivers and demo songs.
Cakewalk Production Plus Pack CD-ROM
This contains Cakewalk Production Plus Pack.
• SONAR 6 LE lets you experience a premium music production environment
• Project5 LE allows intuitive pattern-based music production
• Dimension LE is a sampling synthesizer that’s ready for immediate use
For details on using these software, refer to the installation guides and the software help
provided on the CD-ROM.
* Use of the demo song supplied with this product for any purpose other than private,
personal enjoyment without the permission of the copyright holder is prohibited by law.
Additionally, this data must not be copied, nor used in a secondary copyrighted work
without the permission of the copyright holder.
* Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or
dirty CD-ROM discs may not be read properly. Keep your discs clean using a commercially
available CD cleaner.
DO NOT play a CD-ROM disc on a conventional audio CD player. The
resulting sound may be of a level that could cause permanent hearing loss.
Damage to speakers or other system components may result.
7
UA-25EX_e.book 8 ページ 2008年3月31日 月曜日 午後2時12分
Contents of the Package
■ USB cable
Use this cable to connect the UA-25EX to the USB connector of your computer.
* Please use only the included USB cable. If you require a replacement due to loss or damage,
please contact the nearest Roland Service Center, or an authorized Roland distributor, as
listed on the “Information” page.
■ License agreement
This agreement allows you to use certain software whose copyright is the property of Roland
Corporation. You must read this before opening the CD-ROMs.
You’ll need to provide the following items
External amplifier, speakers, headphones, and microphone are not included.
The external amplifier, speakers, or headphones that you’ll need in order to listen to
sounds that are output via the UA-25EX are not included. Nor is there included a
microphone for connection to the UA-25EX to input audio. You’ll need to obtain these
items separately.
Cables for connecting to an MD or DAT recorder are not included.
You can use an MD or DAT digital recorder to record digital audio, but a cable for
connecting your digital device to the UA-25EX is not included. You’ll need to obtain this
separately.
8
UA-25EX_e.book 9 ページ 2008年3月31日 月曜日 午後2時12分
Panel Descriptions
Front Panel
fig. front.eps
1
2
1.
3
4 5 8 9
12
6 7 10 11
13
Combo input jacks
These are analog audio input jacks with microphone
preamps. They accommodate both XLR type and phone
type plugs, allowing you to use the type appropriate for
the device you’re connecting. They also support either
balanced or unbalanced connections.
Connect a microphone to XLR type jacks. The XLR type
jacks can provide 48 V phantom power, allowing you to
connect a phantom-powered condenser microphone. In
this case, set the rear panel Phantom power switch (23) to
the ON position.
‘
* This instrument is equipped with
balanced (XLR/TRS) type jacks.
Wiring diagrams for these jacks are
shown on the right. Make connections
after first checking the wiring
diagrams of other equipment you
intend to connect.
2.
XLR type plug
Phone type plug
(unblanced)
TRS phone
type plug
(balanced)
GND(SLEEVE)
1:GND
2:HOT
3:COLD
HOT(TIP)
COLD(RING)
Input sensitivity knobs
These adjust the input level of the signals that are input from the front panel combo input jacks (1).
3.
Input impedance select switch
This lets you select either high impedance (Hi-Z) or low impedance (Lo-Z) as appropriate for the
device you’ve connected to the phone type input jack of combo input jack (1) INPUT 2/R.
If you’ve connected a guitar or bass, turn the input impedance select switch on (pressed inward
) to select high impedance (Hi-Z). If you’ve connected a synthesizer or an analog audio device,
turn the input impedance select switch off (outward position
) to select low impedance (Lo-Z).
The phone type jack of the combo input jack INPUT 1/L is fixed at low impedance (Lo-Z).
9
UA-25EX_e.book 10 ページ 2008年3月31日 月曜日 午後2時12分
Panel Descriptions
fig. front.eps
1
3
2
4.
4 5 8 9
12
6 7 10 11
13
Compressor/Limiter threshold knob
This adjusts the threshold of the compressor/limiter.
Turning the knob toward the right will lower the level at which the compressor/limiter begins to
be applied. If the rear panel compressor/limiter type switch (22) is set to compressor 1 (or 2),
the gain (makeup gain) will rise as the threshold level is lowered, producing a fat sound.
Turning this all the way to the left will turn off the compressor/limiter.
* Turning this knob toward the right will strengthen the compressor effect, which may create
the impression that the tone is being affected. If this occurs, turn the threshold knob back
toward the left until the tonal change is not noticeable.
* If you want to turn the circuit itself completely off, set the rear panel compressor/limiter type
switch (22) to the OFF (BYPASS) position.
5.
Peak indicator
This indicates the input signal level. Use the input sensitivity knob (2) for each input jack to
adjust the input level so that the peak indicator does not light.
If the rear panel compressor/limiter type switch (22) is set to OFF (BYPASS) position, the peak
indicator will light red. The compressor/limiter type switch is set to compressor 1, 2 or Limiter
position, the peak indicator will light green.
6.
Digital input switch
If you want to record from the digital input, turn this ON (pressed inward
).
This allows you to synchronize with the external digital device connected to the digital input
connector (17).
Digital input switch
Status
ON
with a digital device connected
to the digital input connector
The input from the digital input connector (17) is sent to the
computer (Digital input mode).
OFF
The input from the combo input jacks (1) is sent to the
computer.
ON
with no digital device
connected to the digital input connector
The audio signal (sound) that is output from the computer via
USB will pass through the UA-25EX and return to the computer
(LoopBack mode).
* In digital input mode you will not hear the sound from the computer. The settings of the direct
monitor section will be ignored. This means that the direct monitor switch (9), STEREO/
MONO select switch (8), and direct monitor volume (10) will not do anything.
10
UA-25EX_e.book 11 ページ 2008年3月31日 月曜日 午後2時12分
Panel Descriptions
7.
USB indicator
This will light blue if the UA-25EX is connected to your computer via the USB cable and the
computer has correctly recognized the UA-25EX.
8.
STEREO/MONO select switch (direct monitor section)
This selects whether the input signal from the combo input jacks (1) will be monitored in stereo
(STEREO) or in monaural (MONO).
If you’ve connected a guitar only to INPUT 2/R, set this to monaural ( pressed inward). Even
if this is set to monaural, the audio signal sent via USB to your computer will be stereo.
* If the digital input switch (6) is on, operating the STEREO/MONO select switch will not do
anything.
9.
Direct monitor switch (direct monitor section)
This selects whether the input signal from the combo input jacks (1) will be output from the
headphone jack (13) and master output jacks (14). The direct monitor ON and OFF will
change whenever this switch is pushed. The direct monitor ON/OFF status can be controlled
directly from ASIO 2.0 compatible software such as Cubase.
Direct monitor switch
Status
ON
(direct monitor indicator lit)
The input signal will be output.
OFF
(direct monitor indicator unlit)
The input signal will not be output. Use the OFF setting if the audio
signal is being passed “through” within the computer, or if you’ve
connected a mixer and are monitoring the input signal directly from
the mixer’s output.
* In digital input mode, direct monitor is always ON, regardless of the direct monitor switch
operation.
10. Direct monitor volume (direct monitor section)
This adjusts the volume at which the input signal from the combo input jacks (1) is output from
the headphone jack (13) and master output jacks (14).
If this is turned all the way to the right, the monitored sound will be twice volume (+6 dB).
11. Direct monitor indicator (direct monitor section)
This will light when direct monitor is on, and will be unlit when it is OFF. If the digital input
switch (6) is turned on, direct monitor will be OFF automatically and the direct monitor
indicator will be extinguished.
12. Output volume
This adjusts the volume that is output from the headphone jack (13) and master output jacks
(14).
13. Headphone jack
Accepts connection of headphones. This jack will output the same sound as the master output
jacks (14). Sound will be output from the master output jacks even if headphones are
connected.
11
UA-25EX_e.book 12 ページ 2008年3月31日 月曜日 午後2時12分
Panel Descriptions
Rear Panel
fig.rear.eps
15
14
16 17
22
19
18
20
21
23
14. Master output jacks (TRS balanced type, RCA phono type)
These are output jacks for analog audio signals. The phone jacks and RCA phono jacks output
the same signal. You may use whichever type of jack is appropriate for the connected device
or the type of cable.
* The TRS balanced master output jacks are wired as
shown on the right. Before you make connections,
check the wiring of the equipment you’re connecting.
GND(SLEEVE)
HOT(TIP)
COLD(RING)
15. Ground lift switch
Normally, you can leave this in the NORMAL (NOR) position.
If you experience noise due to a ground loop, you may be able
to eliminate the noise by setting this to the LIFT position, so that
the sleeve (SLEEVE) pin of the master output TRS balanced jacks
is disconnected from ground.
Mater output jack
(TRS balanced type)
NOR
LIFT
16. Digital output connector (optical)
This is an output connector for digital audio signals. Use this to digitally output audio signals to
a digital audio device such as an MD or DAT. Use an optical cable to make connections.
17. Digital input connector (optical)
This is a input connector for digital audio signals. Use this to digitally input audio signals from
a digital audio device such as a CD, MD, or DAT. Use an optical cable to make connections.
18. MIDI IN/OUT connectors
These are MIDI connectors which transmit and receive MIDI messages between computer.
* The MIDI IN/OUT connectors are not available, if you’re using the UA-25EX in Standard
driver mode (p. 14).
19. Sample rate select switch
This specifies the sample rate at which audio is recorded or played back. If you change the
setting of the sample rate select switch, you must close all software, disconnect the USB cable
that connects the UA-25EX to your computer, and then reconnect the USB cable.
* If you are using Standard driver mode (the Advanced Driver switch turned off), the sample
rate is fixed at 44.1 kHz regardless of the sample rate select switch setting.
* If you want to use 96 kHz, set the switch to “96R” while recording and to “96P” while
playing back.
12
UA-25EX_e.book 13 ページ 2008年3月31日 月曜日 午後2時12分
Panel Descriptions
20. USB connector
Use a USB cable to connect this to your computer.
21. ADVANCED DRIVER switch
This switches the operation mode of the UA-25EX.
The UA-25EX has two operating modes, Advanced mode and Standard driver mode, and
each mode uses a different driver.
If you change the setting of this switch, you must close all software, disconnect the USB cable
that connects the UA-25EX to your computer, and then reconnect the USB cable.
ON (Advanced mode)
In this mode you can use the included UA-25EX driver to record, play and edit audio with
high quality and stable timing. Choose this mode if you’re using sequencer software or
audio editing software.
OFF (Standard driver mode)
Choose this mode if you’re using software that uses the standard audio driver included with
your operating system.
* The sample rate will be fixed at 44.1 kHz/16-bit regardless of the setting of the UA25EX’s sample rate select switch, when using Standard driver mode.
* The MIDI IN/OUT connectors are not available when using Standard driver mode.
For details on the driver operation mode, refer to “What is a Driver?” (p. 14).
22. Compressor/Limiter type switch
This selects the type of hardware compressor/limiter that is applied to the input signal from the
combo input jacks (1). Use the compressor/limiter threshold knob (4) to adjusts the threshold of
the compressor/limiter.
The UA-25EX provides two type of compressors, each type have different attack time.
Switch
Explanation
Compressor 1
(COMP 1)
A compressor with a short attack time, suitable for vocals.
Compressor 2
(COMP 2)
A compressor with a long attack, suitable for recording instruments such as percussion
or acoustic guitar.
Limiter
(LIMIT)
This applies mild compression when an unexpected, high-volume signal is input,
preventing clipping noise from occurring before the AD converter.
* Clipping noise will occur if the input exceeds the range of the limiter.
OFF
(BYPASS)
The compressor/limiter circuit will be completely bypassed.
23. Phantom power switch
This is an ON/OFF switch for the phantom power that is supplied to the XLR connectors of the
front panel combo input jacks (1).
* You must leave the phantom power turned off unless condenser microphones requiring
phantom power are connected to the XLR connectors. Supplying phantom power to a
dynamic microphone or to an audio playback device may cause malfunctions. For details on
the requirements of your microphone, refer to its owner’s manual.
* The UA-25EX’s phantom power supply: DC 48 V, 8 mA maximum.
13
UA-25EX_e.book 14 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
What is a Driver?
A driver is software that transfers data between the UA-25EX and application software on your
computer when your computer and the UA-25EX are connected via a USB cable. You will need
to install the driver before connecting the UA-25EX with your computer.
The driver sends data from the application to the UA-25EX, and conversely from the UA-25EX
to the application.
The UA-25EX has two operating modes, Advanced mode and Standard driver mode, and
each mode uses a different driver.
Advanced mode
The UA-25EX will operate in this mode when its rear panel advanced driver switch is ON.
Normally, you should use this setting.
You can use the native driver included on the UA-25EX Driver CD-ROM to record, play, and
edit audio with high quality and stable timing.
In Advanced mode, signals are transferred between the UA-25EX and the computer at a bit
depth of 24 bits and a sample rate of 44.1/48/96 kHz.
Choose Advanced mode if you’re using software that supports 24-bit audio, such as the
Cakewalk series or if you’re using ASIO-compatible or CoreAudio-compatible software that is
able to record, play, and edit high-quality audio, such as Cubase or Logic.
Standard driver mode
The UA-25EX will operate in this mode when its rear panel advanced driver switch is OFF. The
standard USB audio driver provided by the operating system will be used.
In Standard driver mode, signals are transferred between the UA-25EX and the computer at a
bit depth of 16 bits and a sample rate of 44.1 kHz.
Choose this mode if you are using software that uses the standard functionality provided by the
operating system.
Normally, the driver will be installed automatically when you connect the UA-25EX to your
computer via the USB cable.
* The driver included with the operating system does not support ASIO.
* The MIDI IN/OUT connectors are not available when using Standard driver mode.
14
UA-25EX_e.book 15 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
The installation procedure and settings will differ depending on your system.
If you’re using Advanced mode, proceed to one of the following sections as appropriate
for your system.
• Windows Vista users ......... p. 15
• Windows XP users............. p. 18
• Mac OS X users ................ p. 21
Driver Installation and Settings (Windows Vista)
Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or
USB mouse, if used).
1
2
3
Close all applications before you install the driver.
Insert the included UA-25EX Driver CD-ROM into your computer.
Start up the installer for the Windows driver.
1. Choose [Start] - [Computer].
2. In the CD-ROM, double-click the “Driver (Vista)” folder.
3. Double-click the Setup icon.
* If you see a message telling you that “Drivers must be installed by an administrator,” log on
to Windows as a user whose account type is Administrator, and perform the installation
again.
4
5
A user account control screen will appear; click [Continue].
The screen will indicate “EDIROL UA-25EX Driver will be installed on your computer.” Click
[Next].
* If any other message appears, proceed as directed by that message.
6
7
To begin the installation, click [Next].
If a Windows security dialog box appears, click [Install].
The screen will indicate “UA-25EX driver has been installed.”
* If any other message appears, proceed as directed by that message.
8
9
Set the UA-25EX’s advanced driver switch to the “ON” position.
Use the USB cable to connect the UA-25EX to your computer.
15
UA-25EX_e.book 16 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
10
The message “Installing device driver software” will appear in the lower right corner of the
screen, and the driver will be installed automatically.
* If any other message appears, note the content of the message and close the message.
When the message “Device driver software was installed successfully” appears in the lower
right corner of the screen, installation is complete.
Click [Close] to close the “Driver Setup” dialog box.
11
If the “System settings changed” dialog box appears, click [Yes] and restart Windows.
This completes installation of the UA-25EX driver. As described in following, make settings of
your software
Input/Output Device Settings for Your Software
In order to get the best performance from the software you are using, you must choose the
appropriate input/output device settings for your software, as described below. (For the
procedure, refer to the owner’s manual of the application you’re using.)
Audio input/output devices
The UA-25EX has two input and two output audio channels.
• WAVE OUT device:
• WAVE IN device:
• ASIO device:
OUT (UA-25EX)
IN (UA-25EX)
EDIROL UA-25EX
* If you’re using the UA-25EX with an ASIO-compatible application, choose “EDIROL UA25EX” in the ASIO settings of your application.
* To prevent an audio feedback loop or double monitoring, turn monitoring off in your
application, or make settings so that ASIO Direct Monitor is used.
* We recommend that you set your application to not use Windows’ Microsoft GS Wavetable
Synth while using the UA-25EX via ASIO. (This will decrease the processing load, and make
it easier to change the driver buffer size.)
MIDI input/output devices
* The Media Player included with Windows Vista cannot use the UA-25EX’s MIDI input/output
device.
In your MIDI-compatible application, select the following devices.
• MIDI OUT device:
UA-25EX
• MIDI IN device:
UA-25EX
16
UA-25EX_e.book 17 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
Settings for Using the UA-25EX with Windows Media Player
1
Open the “Control Panel,” click “Hardware and Sounds,” and then click “Sounds.”
* If you’ve selected the Classic view, double-click “Sounds.”
2
3
4
In “Playback,” select the EDIROL UA-25EX’s “OUT,” and click “Set as default.”
Click [OK] to close “Sounds.”
Start up Windows Media Player, and select and play an audio file.
17
UA-25EX_e.book 18 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
Driver Installation and Settings (Windows XP)
Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or
USB mouse, if used).
1
2
3
Close all applications before you install the driver.
Insert the included UA-25EX Driver CD-ROM into your computer.
Start up the installer for the Windows driver.
1. Choose [Start] - [My Computer].
2. In the CD-ROM, double-click the “Driver (XP)” folder.
3. Double-click the Setup icon.
* If an “Install as different user” dialog box appears, click [Cancel], log onto windows using
an Administrator account, and perform the installation again.
4
The screen will indicate “EDIROL UA-25EX Driver will be installed on your computer.” Click
[Next].
* If any other message appears, proceed as directed by that message.
5
6
To begin the installation, click [Next].
If a dialog box indicating “Software installation” appears, click [Continue Anyway] to continue
the installation.
* If you are unable to continue, click [OK] to stop the installation for the time being, and refer
to “Appendix: Troubleshooting” (p. 37).
The screen will indicate “Ready to install the driver.”
* If any other message appears, proceed as directed by that message.
7
18
Set the UA-25EX’s advanced driver switch to the “ON” position.
UA-25EX_e.book 19 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
8
Use the USB cable to connect the UA-25EX to your computer.
1. In the lower right corner of the screen, your computer will indicate “Found New Hardware.”
Please wait until the “Found New Hardware Wizard” appears.
* It may take some time before the “Found New Hardware Wizard” appears.
2. If you are asked whether you want to connect to Windows Update, choose “No” and click
[Next].
3. Choose “Install the software automatically (recommended),” and click [Next].
4. If the “Hardware Installation” dialog box appears, click [Continue Anyway] to continue the
installation.
* If you are unable to continue, click [OK] to stop the installation for the time being, and
refer to Appendix: Troubleshooting (p. 37).
5. If the screen indicates “Completing the Found New Hardware Wizard,” click [Finish].
9
10
If the “Driver Setup” dialog box appears, click [Close] to close the “Driver Setup” dialog box.
If the “System Settings Change” dialog box appears, click [Yes] to restart Windows.
This completes installation of the UA-25EX driver. As described in following, make settings of
your software
* If you are unable to use the UA-25EX after connecting it, it is possible that a problem has
occurred. Refer to “Appendix: Troubleshooting” (p. 37).
Giving Priority to Background Service
On Windows XP, if you omit making this setting, you may experience sound dropout. By
making this setting you may be able to solve such problems. Be sure to make this setting before
you begin using the UA-25EX.
1
Open the “Control Panel,” and double-click “System.”
* If you don’t see the above icon, click “Performance and Maintenance,” and then click
“System.”
2
3
4
Click the “Advanced” tab, click [Settings] located in the Performance area, and click the
“Advanced” tab.
Choose “Background services,” and click [OK].
Click [OK] to close “System Properties.”
19
UA-25EX_e.book 20 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
Input/Output Device Settings for Your Software
In order to get the best performance from the software you are using, you must choose the
appropriate input/output device settings for your software, as described below. (For the
procedure, refer to the owner’s manual of the application you’re using.)
Audio input/output devices
The UA-25EX has two input and two output audio channels.
• WAVE OUT device:
• WAVE IN device:
• ASIO device:
OUT (UA-25EX)
IN (UA-25EX)
EDIROL UA-25EX
* If you’re using the UA-25EX with an ASIO-compatible application, choose “EDIROL UA25EX” in the ASIO settings of your application.
* To prevent an audio feedback loop or double monitoring, turn monitoring off in your
application, or make settings so that ASIO Direct Monitor is used.
* We recommend that you set your application to not use Windows’ Microsoft GS Wavetable
Synth while using the UA-25EX via ASIO. (This will decrease the processing load, and make
it easier to change the driver buffer size.)
MIDI input/output devices
In your MIDI-compatible application, select the following devices.
• MIDI OUT device:
UA-25EX
• MIDI IN device:
UA-25EX
Settings for Using the UA-25EX with Windows Media Player
1
Open the “Control Panel,” and double-click “Sounds and Multimedia” or “Sounds and Audio
Devices.”
* If you don’t see the above icon, click “Sounds, Audio, and Audio Devices,” and then click
“Sounds and Audio Devices.”
2
Click the “Audio” tab. Select “UA-25EX” in the “Sound Playback” area, and choose “UA25EX” in the “MIDI Music Playback” area.
* If you are unable to select the above WAVE/MIDI ports, it is possible that a problem has
occurred. Refer to “Troubleshooting.”
3
4
20
Click [OK] to close “Sound and Multimedia Properties” or “Sound and Audio Device
Properties.”
Start up Windows Media Player, and select and play an audio file.
UA-25EX_e.book 21 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
Driver Installation and Settings (Mac OS X)
Start up the operating system with all USB cables disconnected (except for the keyboard and
mouse).
* If the “Authenticate” dialog box appears during the installation, input the password and
click [OK].
1
2
3
4
5
6
7
8
9
10
Close all applications before you perform the installation.
Insert the included UA-25EX Driver CD-ROM into your computer.
In the CD-ROM, double-click the “Driver (Mac OS X)” folder.
Double-click “UA25EXUSBDriver.pkg”
In some cases, you will see a message saying “In order to determine whether installation is
possible, this installer package must run a program. Continue?” In this case, click [Continue].
The display will indicate “Welcome to the EDIROL UA-25EX Driver Installer.” Click [Continue].
The display will indicate “Select a Destination.” Click the drive in which the operating system is
installed to select it, and then click [Continue].
The display will indicate “Easy Install.” Click [Install] or [Upgrade].
The display will indicate “Installing this software requires you to restart your computer when
the installation is done.” Click [Continue Installation].
The display will indicate “The software was successfully installed.” Click [Restart] to restart your
computer.
* It may take some time for your computer to restart.
This completes installation of the UA-25EX driver.
21
UA-25EX_e.book 22 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
Audio Input/Output Settings
1
2
3
4
Set the UA-25EX’s advanced driver switch to the “ON” position.
Use the USB cable to connect the UA-25EX to your computer.
Open “System Preferences” and click “Sound.”
Choose “EDIROL UA-25EX ??kHz” for each of the following items.
(?? will depend on the sample rate setting of the UA-25EX itself.)
• In the “Sound Effects” tab, “Play alerts and sound effects through”
• In the “Output” tab, “Choose a device for sound output”
• In the “Input” tab, “Choose a device for sound input”
MIDI Input/Output Settings
1
2
3
4
Use the USB cable to connect the UA-25EX to your computer.
In the Application–Utilities folder, double-click “Audio MIDI Setup” to open it.
Click the “MIDI Devices” tab.
Verify that “UA-25EX” is shown in the “Audio MIDI Setup” dialog box.
* If “UA-25EX” is not shown, or if it is shown in gray, the UA-25EX has not been recognized
correctly. Try clicking “Rescan MIDI.” You can also try disconnecting the UA-25EX’s USB
cable and reconnecting it.
* If you have installed a driver of a different version, it may be that the previous settings
remain. In this case, select the “UA-25EX” or “EDIROL UA-25EX” that is displayed in gray,
and click “Remove Device” to remove the settings.
5
6
Click “Add Device.” “New external device” will appear.
Specify the “Device name” of the “New external device.”
1. Click the added “New external device” to select it, and click “See information.”
2. In the “Device name” field, enter “UA-25EX.”
7
Using the mouse, drag the up/down arrows that indicate the input/output ports so that they are
connected in the following way.
• The first up/down arrows of “UA-25EX” are connected to the up/down arrows of the added
“UA-25EX”
22
UA-25EX_e.book 23 ページ 2008年3月31日 月曜日 午後2時12分
Introduction
8
Verify that MIDI reception and transmission can occur correctly. Follow the procedure given
below.
1. Click “Test setup.” The shape of the mouse cursor will change.
* If a sound module is connected to the UA-25EX, the following step will cause your sound
module to produce a relatively loud sound; turn down the volume of the sound module
before you continue.
2. If a sound module is connected to the UA-25EX’s MIDI OUT connector, click the
corresponding external device. If the sound module produces sound, the setup is correct.
3. Click “Test setup” once again to end the test.
9
Close the “Audio MIDI Setup” dialog box. This completes the setup.
Before You Use the UA-25EX with Your Software
1
2
First use the USB cable to connect the UA-25EX to your computer, and then start up the
software.
Choose “EDIROL UA-25EX ??kHz” in the audio driver settings of your software.
(“??kHz” will depend on the sample rate setting of the UA-25EX itself.)
3
Choose “UA-25EX” in the MIDI driver settings of your software.
For details, refer to the manual of the software you’re using.
23
UA-25EX_e.book 24 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
This section explains the basic connections and data flow for the UA-25EX. Refer to the block
diagram printed on the front cover of the manual as you read this section.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the
volume, and turn off the power on all devices before making any connections.
* When connection cables containing resistors are used, the volume level of equipment
connected to the inputs (input jacks) may be low. If this happens, use connection cables that
do not contain resistors.
* Don’t connect anything to input jacks you are not using.
* Howling could be produced depending on the location of microphones relative to speakers.
This can be remedied by:
1. Changing the orientation of the microphone(s).
2. Relocating microphone(s) at a greater distance from speakers.
3. Lowering volume levels.
24
UA-25EX_e.book 25 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Basic Connections
Use the USB cable to connect the UA-25EX to your computer.
MIDI data and audio data are transferred in both directions via the USB cable.
By connecting headphones or monitor speakers as shown in the illustration, you can monitor
the playback from your software or the sound from an instrument or audio device connected to
the UA-25EX.
fig.basic.eps
Amplified Speakers
Front Panel
Rear Panel
Computer
Headphones
25
UA-25EX_e.book 26 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Connecting a Microphone or a Guitar
With the connections and settings described here, you can listen to audio data play back from
your computer while you record just your vocal or guitar performance into your sequencer.
fig.mic-guitar.eps
Guitar/Bass
Connect to
INPUT 2
Hi-z
Adjust the Input
Sensitivity
Adjust the Input
Sensitivity
Specify the
Sample Rate
Turn ON when connecting a
phantom powerd microphone
Connect a microphone
to XLR type jacks
Connections
The sound of the microphone connected to INPUT 1 will be recorded in your computer on the
left (L) channel. If you connect a source to INPUT 2, it will be recorded on the right (R) channel.
Connect your guitar/bass to INPUT 2.
Input impedance select switch
If you’ve connected a guitar/bass to INPUT 2:
Select Hi-Z (
pressed inward).
If you’ve connected a microphone to INPUT 2:
Select Lo-Z (
outward position).
Phantom power switch
If you’re using a condenser microphone, turn the phantom power switch on.
* If a device that does not use phantom power is connected, you must turn off the phantom
power switch. Failing to do so may cause malfunction.
26
UA-25EX_e.book 27 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Input sensitivity knob
Use the input sensitivity knob to adjust the input level. You can obtain the best recording quality
by turning the input sensitivity knobs as high as possible without causing the peak indicators to
light.
Sample rate select switch
Set this to the same sample rate as selected in your recording software.
If you change the UA-25EX’s sample rate, you must disconnect the USB cable that connects the
UA-25EX to your computer, and then reconnect the USB cable in order for the new setting to
take effect.
STEREO/MONO select switch (Direct Monitor section)
This selects whether the input signal is to be monitored in stereo or in monaural.
Direct Monitor switch
You can turn this on to monitor the input signal.
Turn this off if you want to pass the signal “through” within your software.
Direct Monitor volume
This adjusts the balance between the monitor volume and the volume of the audio being
played back from your computer.
Using the direct monitor volume control to adjust the volume will not affect the recording level.
27
UA-25EX_e.book 28 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Connecting a Microphone and Applying the
Compressor
You can obtain a fatter sound by applying a compressor to the input signal from the
microphone.
fig.mic-guitar.eps
Adjust the
Compressor
Threshold
Adjust the Input
Sensitivity
Connect a
microphone to
XLR type jacks.
Turn to COMP1 when vocal sound is input.
Turn to COMP2 when instruments sound
(such as acoustic guitar or percussion) is
input.
Turn ON when connecting a
phantom powerd microphone
Connections
The sound of the microphone connected to INPUT 1 will be recorded in your computer on the
left (L) channel. If you connect a source to INPUT 2, it will be recorded on the right (R) channel.
Connect your guitar to INPUT 2.
Phantom power switch
If you’re using a condenser microphone, turn the phantom power switch on.
* If a device that does not use phantom power is connected, you must turn off the phantom
power switch. Failing to do so may cause malfunction.
Input sensitivity knob
Use the input sensitivity knob to adjust the input level. You can obtain the best recording quality
by turning the input sensitivity knobs as high as possible without causing the peak indicators to
light.
Compressor/limiter threshold knob
Turning this knob toward the right will apply stronger compression. This will also increase the
gain (makeup gain), so you should use the input sensitivity knob and threshold knob to adjust
the input level so that the peak indicator does not light.
* The compressor (and the limiter) does not support stereo signals. The compressor/limiter for
INPUT 1 and INPUT 2 will each operate independently.
* Turning this knob toward the right will strengthen the compressor effect, which may create
the impression that the tone is being affected. If this occurs, turn the threshold knob back
toward the left until the tonal change is not noticeable.
28
UA-25EX_e.book 29 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Sample rate select switch
Set this to the same sample rate as selected in your recording software.
If you change the UA-25EX’s sample rate, you must disconnect the USB cable that connects the
UA-25EX to your computer, and then reconnect the USB cable in order for the new setting to
take effect.
STEREO/MONO select switch (Direct Monitor section)
This selects whether the input signal is to be monitored in stereo or in monaural. If you’ve
connected a microphone as shown in this example, choose the monaural (MONO) setting.
Direct Monitor switch
If this is on, the direct monitor indicator will be lit. Also you’ll be able to monitor the sound with
the compressor applied.
Direct Monitor volume
This adjusts the balance between the monitor volume and the volume of the audio being
played back from your computer.
Using the direct monitor volume control to adjust the volume will not affect the recording level.
29
UA-25EX_e.book 30 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Recording a Digital Signal into Your Computer
fig.digital.eps
MD/CD/DAT Player,
HDD Recorder, etc.
ON
Specify the Sample Rate:
Set this to match the sample rate of your
digital playback device.
Connections
Connect your digital device to the digital input connector.
Sample rate select switch
Set this to match the sample rate of the software you’re using to record your digital playback
device.
If you change the UA-25EX’s sample rate, you must disconnect the USB cable that connects the
UA-25EX to your computer, and then reconnect the USB cable in order for the new setting to
take effect.
* If you want to record at 96 kHz, you must set this switch to “96R” (record).
Digital input switch
Turn this on so that the UA-25EX will synchronize to the digital signal being input to the digital
input connector.
Other notes
The direct monitor volume control will have no effect.
30
UA-25EX_e.book 31 ページ 2008年3月31日 月曜日 午後2時12分
Basic Connections and Settings
Recording to an MD or Other Digital Device
fig.digital2.eps
MD/DAT Recorder,
HDD Recorder, etc.
Specify the Sample Rate:
Select a sample rate that your recordeng
device is able to record. Choose the
same sample rate as your software or the
audio data you are playing back.
Connections
Connect your digital device to the digital output connector.
Sample rate select switch
Set this to match the sample rate of your digital recording device and the sample rate of your
software or the audio data you are playing back.
If you change the UA-25EX’s sample rate, you must disconnect the USB cable that connects the
UA-25EX to your computer, and then reconnect the USB cable in order for the new setting to
take effect.
* If you recorded at 96 kHz, you must set this switch to “96P” (playback).
Other notes
The signals being input from the combo input jacks are not output directly from the digital
output connector.
31
UA-25EX_e.book 32 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Driver settings
Adjusting the Latency and Other Settings (Windows)
Changing or Viewing the Settings
1
2
Before you change the driver settings, you must close all programs that are using the UA-25EX.
This is not necessary if you’re merely viewing the settings.
Open the “Control Panel” and click “EDIROL UA-25EX.”
* If you don’t see the above icon, click “Switch to classic view.”
The “EDIROL UA-25EX Driver settings” dialog box will appear.
3
If you want to change the settings, change the settings and then click [OK]. If you merely want
to view the settings, be sure to click [Cancel].
* For details about each item, refer to Items in the Settings Dialog Box (p. 33).
32
UA-25EX_e.book 33 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Driver settings
Items in the Settings Dialog Box
* If you change the buffer size, you must restart the applications that are using the UA-25EX,
or if your application has an audio device test function, you must execute that test function.
Some applications may also have a buffer size adjustment as part of their own audio
settings.
“Audio Buffer Size” option
Normally, you should leave the buffer size setting at the fifth position from the left.
“Use Smaller ASIO Buffer Size” check box
By selecting this check box you can minimize the buffer size when using an ASIO-compatible
application.
If you hear clicks or pops in the sound when this check box is selected, clear the check box.
* Adjust the “Audio buffer size” setting with this check box cleared.
“Use ASIO Direct Monitor” check box
Select this check box if you want to use ASIO Direct Monitor functionality in your ASIOcompatible application.
“Light Load” check box
Normally, you should leave this check box cleared.
* If you’ve made a change to the settings, you must disconnect the USB cable from the UA25EX and then reconnect it in order for the new settings to take effect.
Driver information
This shows the version of the currently installed driver.
33
UA-25EX_e.book 34 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Driver settings
Adjusting the Latency and Other Settings (Mac OS X)
Changing or Viewing the Settings
1
2
3
Use the USB cable to connect the UA-25EX to your computer.
In “System Preferences,” click “EDIROL UA-25EX.”
The driver settings panel will appear.
Items in the Driver Settings Panel
* Even if you press [Apply] while the audio software is running, these settings will not be
reflected immediately. The changes will take effect after you exit all of your audio software,
then restart the software.
“Audio buffer size”
This changes the size of the driver’s audio input/output buffer.
If you experience clicks or pops in the sound during playback or recording even after adjusting
the audio buffer size within your software, try increasing this buffer size.
* Some software may not provide a buffer size adjustment.
“Recording margin”
If you experience clicks or noise in the recorded audio data even after adjusting the audio
buffer size within your software, try increasing this recording margin setting.
* Some software may not provide a buffer size adjustment.
“Recording timing”
Adjust this value if the timing of the recorded audio data is offset.
34
UA-25EX_e.book 35 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Driver settings
Driver Uninstallation
Uninstalling the Driver (Windows Vista)
1
2
3
Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or
USB mouse, if used).
Close all applications before performing the uninstallation.
Open “Control Panel” and click “Uninstall a program.”
* If you’re using the Classic View, double-click the “Programs and Features” icon.
4
5
In the list, choose EDIROL UA-25EX Driver, and click “Uninstall/Change.”
If a dialog box regarding User Account Control appears, click [Continue].
* If you are asked to enter the password for an administrative account, log on to Windows as
a user whose account type is Administrator, and then perform the uninstallation.
6
7
The display will indicate “The installed EDIROL UA-25EX Driver will be uninstalled.” and click
the [OK].
When the message “Uninstallation was completed.” is displayed, click [OK] to restart
Windows.
35
UA-25EX_e.book 36 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Driver settings
Uninstalling the Driver (Windows XP)
1
2
3
4
5
Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or
USB mouse, if used).
Close all applications before performing the uninstallation.
Open “Control Panel” and click “Add or Remove Programs.”
In the list, choose EDIROL UA-25EX Driver, and click “Change/Remove.”
The display will indicate “The installed EDIROL UA-25EX Driver will be uninstalled.” and click
the [OK].
* If any other message appears, follow the directions of the message.
6
When the message “Uninstallation was completed.” is displayed, click [OK] to restart Windows.
Uninstalling the Driver (Mac OS X)
1
2
3
4
5
6
Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or
USB mouse, if used).
Close all applications before performing the uninstallation.
Insert the included UA-25EX Driver CD-ROM into your computer.
In the CD-ROM, double-click the “Driver (Mac OS X)” folder.
Double-click “UA25EX_Uninstaller.”
The screen will indicate “This uninstalls EDIROL UA-25EX driver from this Macintosh.” Click
[Uninstall].
* If any other message appears, proceed as directed by that message.
7
8
9
The screen will indicate “Are you sure to uninstall the driver?” Click [OK].
The “Authenticate” dialog box will appear. Enter your password, and click [OK].
The screen will indicate “Uninstallation is completed.” Click [Restart] to restart your computer.
* It may take some time for your computer to restart.
36
UA-25EX_e.book 37 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Can’t Install/Uninstall/Use the Driver
Is the USB connector of your computer usable?
Refer to the owner’s manual of your computer, and verify that the USB connector is usable. You
can’t install the driver unless the USB connector is usable.
Can your computer or USB hub supply enough power?
Check whether the following cases might apply.
• If you’re using a notebook computer that’s running on batteries, the UA-25EX might not
operate stably with some computers. If so, connect your computer to its AC adaptor.
• The power conservation settings of your computer may be limiting the power that is supplied
to USB. Take another look at the settings of your computer.
• Some bus powered USB hubs cannot be used with the UA-25EX. Use a USB hub that
contains a power supply.
Does your computer meet the requirements of the USB specifications?
If your computer does not meet the electrical requirements of the USB specifications, the UA25EX may not operate stably. If so, you may be able to solve the problem by using a selfpowered USB hub.
Is the UA-25EX’s advanced driver switch turned “ON”?
Turn the UA-25EX’s advanced driver switch “ON.”
Did you log on to Windows with the appropriate user privileges?
You must log onto Windows using one of the following user names.
• A user belonging to the Administrators group (e.g., Administrator)
• A user whose account type is Computer Administrator
37
UA-25EX_e.book 38 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Driver Signing Option Setting
You may be unable to install the driver because of the “Driver Signing Option” setting. Check
the following points, and make the appropriate setting.
1. Open the System Properties dialog box.
1. From the Windows Start menu, open the Control Panel.
2. In “Pick a category,” click “Performance and maintenance.”
3. Under “Pick a Control Panel icon,” click the System icon.
* Depending on your setup, the System icon may be shown directly in the Control Panel
(the Classic view). If so, double-click the System icon.
2. Click the “Hardware” tab, and then click [Driver Signing].
3. The Driver Signing Options dialog box will appear. In the Driver Signing Options dialog
box, choose “Warn” or “Ignore,” and then click [OK].
4. Click [OK] to close the System Properties dialog box.
5. Install the driver as described in the “Installation” procedure.
* After you’ve completed the installation, you can return the driver signing options setting to its
original state.
Was the driver installed correctly?
If you are unable to use the UA-25EX even though the driver was installed, it is possible that
the driver was not installed correctly. Uninstall the driver as described in “Driver
Uninstallation” (p. 35), and then install the driver once again.
Is the UA-25EX’s MIDI/WAVE device name shown?
If the device name is not shown, close all applications that are using the UA-25EX, disconnect
the USB cable from the UA-25EX, and then reconnect it.
If this does not solve the problem, uninstall the driver as described in “Driver Uninstallation” (p.
35), and then install the driver once again.
38
UA-25EX_e.book 39 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Can’t Select the UA-25EX Device
Was the driver installed correctly?
Could the computer have entered standby (suspend) mode or hibernation while the UA-25EX was
connected?
If the UA-25EX does not operate correctly after your computer resumes from standby (suspend)
mode or hibernation, close all applications you’re using, disconnect the USB cable from the
UA-25EX, and then reconnect it.
Could you have disconnected and reconnected the USB cable while using the UA-25EX?
The UA-25EX may stop operating correctly if you disconnect and reconnect the USB cable
during use. In this case, close all applications that are using the UA-25EX, disconnect the USB
cable from the UA-25EX, and then reconnect it.
On some computers, the driver will not be loaded correctly if the UA-25EX is already connected
when Windows starts up, making the UA-25EX unusable via USB.
In this case, connect the UA-25EX after Windows has started up.
Can’t Play/Record
Was the driver installed correctly?
Have you made settings in your software?
To make settings, refer to “Introduction” (p. 14), and the owner’s manual of the application
software you’re using.
Could your computer have entered standby (suspend) mode or hibernation during playback or
recording?
If the UA-25EX does not operate correctly after your computer returns from standby (suspend)
mode or hibernation, close all applications you’re using, disconnect the USB cable from the
UA-25EX, and then reconnect it.
Could you have disconnected the USB cable during playback or recording?
The UA-25EX may stop recording or playing correctly if you disconnect and reconnect the USB
cable during recording or playback. Stop playback or recording, and then try playing or
recording again. If you are still unsuccessful, close all applications that are using the UA-25EX,
disconnect the USB cable from the UA-25EX, and then reconnect it.
39
UA-25EX_e.book 40 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
There are Interruptions, Dropouts, or Other Problems in the Sound
During Playback
You may be able to solve the problem by taking the following steps.
Windows Update/ Microsoft Update
Use Microsoft Corporation’s Windows Update or Microsoft Update to update your system to
the most recent state.
System “Performance Options” settings
Follow the procedure described in “Giving Priority to Background Service” (p. 19).
UA-25EX sample rate setting
Make sure that the sample rate setting of your application software matches the sample rate of
the UA-25EX itself.
* After changing the sample rate setting of the UA-25EX itself, you must close all software that
use the UA-25EX, disconnect the USB cable from the UA-25EX, and then reconnect it.
“Audio Buffer Size” in the setting dialog box
1. Open the Settings dialog box as described in “Appendix: Driver settings” (p. 32).
2. Increase the “Audio Buffer Size.”
Clicks or pops may occur in the sound if a LAN is operating
Try disabling the LAN in Device Manager. If this eliminates the clicks or pops, you may be able
to solve the problem by updating your LAN driver or BIOS.
Windows XP: “Hardware Acceleration” in the Display Details
You may be able to eliminate noise during audio playback by adjusting the graphics
acceleration setting.
1. Open the “Control Panel,” and double-click “Display.”
* If you don’t see the above icon, click “Appearance and Thems,” and then click “Display.”
2. Click the “Settings” tab.
3. Click [Advanced] – “Troubleshoot” tab.
4. Adjust the “Hardware acceleration” slider, and click [OK].
5. In “Display Properties,” click [OK] to close the dialog box. Then restart your computer.
You may be able to solve the problem by selecting the “Light Load” check box in the Settings dialog box.
To view or change this setting, follow the procedure described in “Appendix: Driver settings”
(p. 32)
* After you’ve changed this setting, you must disconnect the USB cable from the UA-25EX and
then reconnect it so that the change will take effect. If you are not experiencing problems,
leave this check box cleared (the default setting).
40
UA-25EX_e.book 41 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Try adjusting the audio buffer size in your software.
First, try adjusting the audio buffer size in the software you’re using. If you still experience
clicks or pops during playback or recording, try adjusting the “Audio Buffer Size” in the driver
settings panel.
* Some software may not allow you to adjust the buffer size.
Mac OS: Try setting the “Processor performance” setting to “Highest”.
You may be able to eliminate clicks and pops by making the following setting.
* Some Macintosh computers do not provide a “Processor performance” setting.
1. In “System Preferences,” click “Energy Saver.”
2. Click “Options.”
3. For “Processor performance,” choose “Highest.”
Mac OS: Could you have updated the Mac OS X software while UA-25EX was connected?
It has been found that clicks or pops can occur if you performed a Mac OS X software update
while the UA-25EX was connected. If so, install the driver once again.
Could you have connected the UA-25EX to a USB hub?
Try connecting the UA-25EX directly to a USB connector on your computer.
Windows XP: The power management settings in the control panel may be causing audio playback
to be interrupted.
Use the following procedure to check the settings.
* The contents of the power properties that appear when you double-click power management
will depend on your computer system.
* The example shown here is for a typical system. You should refer to the owner’s manual of
your computer for details.
* Some computers may not have the following settings.
1. From the Windows Control Panel, double-click the System icon.
The System Properties dialog box will appear.
2. Click the Hardware tab.
3. Click Device Manager to access the list of devices.
4. From the list, choose Advanced Power Management Support, and click Properties.
The Advanced Power Management Support Properties dialog box will appear.
5. Click the Settings tab. In Troubleshooting, select the “Don’t poll the power supply status”
check box, and click [OK].
6. In the System Properties dialog box, click [OK].
7. Restart Windows.
41
UA-25EX_e.book 42 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Playback/Recording Halts Midway, and Subsequent Playback/
Recording is Not Possible
While you were using the UA-25EX, could your computer have performed a task with a heavy
processing load, such as accessing a CD-ROM drive or the network?
If a heavy processing load occurs while the UA-25EX is being used, it may not work correctly.
In this case, stop playback/recording, and then start playback/recording once again.
If you are still unable to play/record, close all software that was using the UA-25EX,
disconnect the USB cable from the UA-25EX, and then reconnect it.
The Computer Asks You for the Driver File Even Though You’ve
Installed it
If you connect the UA-25EX to a different USB connector than previously, the computer may ask you
for the driver file. (Windows XP)
This is normal behavior, and should not be a cause for concern. Install the driver according to
the following procedure.
1. Use the USB cable to connect the UA-25EX to your computer.
<Windows XP users>
The indication “Found new hardware” will appear in the lower right corner of the screen.
Wait for the “Found New Hardware Wizard” to appear.
* It may take some time for the “Found New Hardware Wizard” to appear.
2. If you are asked whether you want to connect to Windows Update, choose “No” and click
[Next].
3. Choose “Install the software automatically (recommended),” and click [Next].
4. If the “Hardware Installation” dialog box appears, click [Continue] to continue the
installation.
* If you are unable to continue, click [OK] to halt the installation, and refer to “Driver signing
option settings.”
5. When “Completing the Found New Hardware Wizard” appears, click [Finish].
42
UA-25EX_e.book 43 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Playback Appears to Occur, but the Sound is Not Heard in Your
Headphones
Are the volume controls on the UA-25EX set appropriately?
Adjust the output volume and direct monitor volume controls on the UA-25EX’s front panel.
Is your audio playback system (e.g., stereo) connected correctly?
Could the UA-25EX’s digital input switch be on (digital input mode)?
If the UA-25EX is in digital input mode (p. 10), the audio signal being received at the digital
input jack will be output. The audio signal from your computer will not be output.
Could the UA-25EX’s sample rate select switch be “96R”?
If you want to playback at 96 kHz, set the switch to “96P”.
Are the faders of the Windows volume control raised?
Are the main volume levels of the Macintosh raised?
Is the audio output destination set appropriately in your playback software?
Could your computer have entered standby (suspend) or sleep mode?
Sound From the Device Connected to the Input Jacks is Not Heard
Through the Headphones, or is Not Loud Enough
Are the input sensitivity knobs and the direct monitor volume knob set appropriately?
Turn the knobs toward the right to adjust the volume.
Is the output volume set appropriately?
Turn the knob toward the right to adjust the volume.
43
UA-25EX_e.book 44 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Can’t Record via a Digital Connection
If you’re capturing audio data from a CD or MD into your computer, is the digital input switch turned
on?
Turn the digital input switch on so that the UA-25EX will be in digital input mode (p. 10).
Does the sample rate setting of your software match the sample rate of the digital device that’s
connected to the digital input connector?
Set them to the same sample rate.
If you’ve switched the UA-25EX’s sample rate setting, you must disconnect the USB cable from
the UA-25EX, and then reconnect it to get the new setting to take effect.
Data containing the SCMS copy-prohibit flag cannot be recorded digitally.
The UA-25EX complies with SCMS, and if data containing the SCMS copy-prohibit flag is
input, for example from an MD that was digitally copied from a commercial music CD, the UA25EX will not allow this data to be recorded on the computer.
The audio will be output from the master output jacks and the headphone jack.
Can’t Play or Record 24-bit Audio Data
Does the software you’re using support 24-bit audio data?
Noise or Distortion is Heard in Sound that’s Not Played by Your
Computer
Could two or more audio devices such as the UA-25EX or a sound module be connected to the
computer?
Turn the ground lift switch to LIFT position, and see whether this eliminates the noise.
If a USB-compatible MIDI sound module and the UA-25EX are connected via USB to the same
computer, and the output of the MIDI sound module is connected to the combo input jacks of
the UA-25EX, noise from the computer may pass through the MIDI sound module and be heard
from the UA-25EX.
If turning LIFT the ground lift switch does not eliminate the noise, try using a self-powered hub to
connect the MIDI sound module and the UA-25EX in parallel, or connect the MIDI sound
module in series or via a MIDI interface.
Could a microphone or guitar be left connected?
If a microphone or guitar is connected to the UA-25EX, unplug the microphone or guitar and
turn the input sensitivity knob all the way to the left so that the input level is lowered.
Have you grounded the computer?
You may be able to solve the problem by grounding the computer’s chassis, or the ground pin
of the computer’s AC power supply plug. Also check whether there might be a device nearby
that generates a strong magnetic field, such as a television or microwave oven.
44
UA-25EX_e.book 45 ページ 2008年3月31日 月曜日 午後2時12分
Appendix: Troubleshooting
Noise is Heard with the Guitar Sound
Does lowering your guitar’s volume decrease the noise?
If the noise decreases when you lower the volume of your guitar, it may be that your guitar’s
pickups are being affected by noise from your computer or display.
Move your guitar as far away from your computer as possible.
Guitar Sound is Not Loud Enough
Are you using the correct connector?
Connect your guitar to the INPUT 2 combo input jack.
Is the input impedance select switch set correctly?
Set the input impedance select switch to the Hi-Z position.
Could you be using a connection cable that contains a resistor?
Use a connection cable that does not contain a resistor.
Microphone is Not Loud Enough
Connect your microphone to the XLR type jacks of the combo input jack.
Is the input level set appropriately?
Turn the input sensitivity knob toward the right to adjust the input volume.
Could you be using a connection cable that contains a resistor?
Use a connection cable that does not contain a resistor.
Sound of the Device Connected to the Input Jacks is Distorted
Could the peak/limiter indicator be lighting?
If you are inputting audio via the combo input jacks, use the UA-25EX’s input sensitivity knobs
to decrease the input level.
45
UA-25EX_e.book 46 ページ 2008年3月31日 月曜日 午後2時12分
Specifications
UA-25EX:USB Audio Interface
Number of Audio Record/
Playback Channels
Record:
Playback:
DIGITAL IN SWITCH = OFF:
DIGITAL IN SWITCH = ON:
PC interface:
AD/DA Conversion:
24 bits (ADVANCED DRIVER switch=ON)
16 bits (ADVANCED DRIVER switch=OFF)
24 bits (linear)
Digital output:
Digital input:
AD/DA Conversion:
44.1/48/96 kHz
44.1/48/96 kHz
44.1/48/96 kHz
Signal Processing
Sampling Frequency
1 pair of stereo
1 pair of stereo
Full duplex (except for 96 kHz setting)
Recording only
* ADVANCED DRIVER switch=OFF: 44.1 kHz only
Frequency Response
Nominal Input Level
96.0 kHz:
48.0 kHz:
44.1 kHz:
20 Hz to 40 kHz (+0 dB/-2 dB)
20 Hz to 22 kHz (+0 dB/-1 dB)
20 Hz to 20 kHz (+0 dB/-1 dB)
Input Jack L, R (XLR type):
Input Jack L, R (1/4 inch TRS phone type):
-60 to -20 dBu
-36 to +4 dBu
* Maximum input level: Nominal Input Level + 12 dB
Nominal Output Level
Output Jack L, R (1/4 inch TRS phone type):
Output Jack L, R (RCA phono type):
+4 dBu (balanced)
-2 dBu
* Maximum output level: Nominal Output Level + 12 dB
Output Jack:
Residual Noise Level
-96 dBu (S/N ratio: 105 dB typ.)
* Input terminated with 1 k ohms, OUTPUT VOLUME: max.,
INPUT MONITOR: min., IHF-A, typ.
Microphone Pre-Amp
Phantom power 48 V / 8 mA max.
Analog Limiter or compressor
Interface
USB
Digital input/output (Optical type)
Conforms to IEC60958 consumer format.
MIDI input/output
46
UA-25EX_e.book 47 ページ 2008年3月31日 月曜日 午後2時12分
Specifications
<Front Panel>
Input Jack L, R
XLR type (balanced, phantom power +48 V)
1/4 inch TRS phone type (balanced)
* Input Jack R: high impedance is supported.
Headphones Jack
Stereo 1/4 inch phone type
Connectors
<Rear Panel>
Digital Input Connector (Optical type)
Digital Output Connector (Optical type)
Output Jack L, R
1/4 inch TRS phone type (balanced)
RCA phono type
MIDI Connectors (IN, OUT)
USB Connector (B type)
Power Supply
USB Bus Power
Current Draw
480 mA
Dimensions
164 (W) x 133 (D) x 46 (H) mm
6-1/2 (W) x 5-1/4 (D) x 1-13/16 (H) inches
Weight
565 g/ 1 lb. 4 oz.
Accessories
Owner’s Manual, USB cable, UA-25EX Driver CD-ROM,
Cakewalk Production Plus Pack CD-ROM
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specifications, appearance of this unit and/or contents of this
package are subject to change without prior notice.
47
UA-25EX_e.book 48 ページ 2008年3月31日 月曜日 午後2時12分
Index
I
A
Administrator ............................... 15,
ADVANCED DRIVER switch ...................
Advanced mode .................................
ASIO ................................... 14, 16,
Audio device ............................... 16,
Audio MIDI Setup ...............................
Authenticate ................................ 21,
18
13
14
20
20
22
36
B
Background services ............................ 19
Balance ............................................ 9
Bass guitar ....................................... 26
BYPASS .......................................... 13
C
Cakewalk Production Plus Pack .................. 7
Combo input jacks ................................ 9
Compressor ...................................... 10
Compressor/Limiter type switch ............... 13
Condenser microphone ................ 9, 26, 28
CoreAudio ....................................... 14
D
Digital input ................................ 10, 12
Digital input mode .............................. 10
Digital output connector ........................ 12
Dimension LE ...................................... 7
Direct monitor .............................. 27, 29
Direct monitor indicator ........................ 11
Direct monitor switch ........................... 11
Direct monitor volume .......................... 11
G
Ground lift switch ............................... 12
Guitar ............................................ 26
H
Headphone jack ................................. 11
High impedance .................................. 9
Hi-Z ................................................. 9
48
Impedance ........................................ 9
Input
Analog audio ................................ 9
Audio ........................................ 22
Audio device ........................... 16, 20
Combo input jack ........................... 9
Digital audio ..................... 10, 12, 30
Impedance .............................. 9, 26
Level .......................................... 9
MIDI device ............................ 16, 20
Sensitivity ..................................... 9
L
LIFT ................................................ 12
Limiter ............................................ 10
Limiter type switch ............................... 13
LoopBack mode ................................. 10
Low impedance ................................... 9
Lo-Z ................................................ 9
M
Master output jack ..............................
Media Player ............................... 17,
Microphone ................................. 26,
MIDI connector ..................................
MIDI device ................................. 16,
12
20
28
12
20
N
NOR .............................................. 12
NORMAL ......................................... 12
O
Output
Audio
........................................
Audio device ........................... 16,
Digital audio ........................... 12,
Headphone .................................
Master .......................................
MIDI device ............................ 16,
Volume ......................................
22
20
31
11
12
20
11
UA-25EX_e.book 49 ページ 2008年3月31日 月曜日 午後2時12分
Index
P
Peak indicator ................................... 10
Phantom power ................................... 9
Phantom power switch .......................... 13
Phone type jack ................................... 9
Preamp ............................................. 9
Project5 LE ......................................... 7
R
RCA phono jack
.................................
12
S
Sample rate ................................. 27, 29
Sample rate select switch ....................... 12
SLEEVE ........................................... 12
SONAR 6 LE ....................................... 7
Standard driver mode .......................... 14
STEREO/MONO select switch ................. 11
System Preferences .............................. 22
T
Threshold knob .................................. 10
TRS jack .......................................... 12
TRS type ............................................ 9
U
Unbalance ......................................... 9
Uninstall .......................................... 35
USB cable .......................................... 8
USB connector ................................... 13
USB indicator .................................... 11
User account control ............................ 15
V
Vocal
.............................................
26
W
Windows Media Player
...................
17, 20
X
XLR type
............................................
9
49
UA-25EX_e.book 50 ページ 2008年3月31日 月曜日 午後2時12分
For EU Countries
This product complies with the requirements of EMC Directive 2004/108/EC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
UA-25EX
USB Audio Interface
Roland Corporation U.S.
5100 S.Eastern Avenue, Los Angeles, CA 90040-2938
(323) 890-3700
UA-25EX_e.book 51 ページ 2008年3月31日 月曜日 午後2時12分
For EU Countries
For China
UA-25EX_e.book 52 ページ 2008年3月31日 月曜日 午後2時12分
Information
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe
Deutschland
TEL: 0700 33 47 65 20
Italia
TEL: 02 93778329
NORTH AMERICA
CANADA
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar Al Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (022)-418-5531
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized
EDIROL/Roland distributor in your country as shown below.
HONG KONG
BRAZIL
TRINIDAD
IRELAND
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
INDIA
CHILE
URUGUAY
ITALY
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
NORWAY
COLOMBIA
VENEZUELA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
INDONESIA
PT Citra IntiRama
Jl. Cideng Timur No. 15J-15O
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
100-108 Soi Verng
Nakornkasem, New
Road,Sumpantawongse,
Bangkok 10100 THAILAND
TEL: (02) 224-8821
AUSTRALIA/
NEW ZEALAND
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
VIET NAM
BARBADOS
Suoi Nhac Company, Ltd
370 Cach Mang Thang Tam St.
Dist.3, Ho Chi Minh City,
VIET NAM
TEL: 9316540
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
CURACAO
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EUROPE
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
POLAND
ROLAND POLSKA SP. Z O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
PORTUGAL
AUSTRIA
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
ROMANIA
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
GUATEMALA
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CROATIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb
TEL: (1) 466 8493
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
DENMARK
SWEDEN
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
FINLAND
SWITZERLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
GERMANY
UKRAINE
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo,
UKRAINE
TEL: (03131) 414-40
TEL: (23) 511011
KUWAIT
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Al-Yousifi Service Center
P.O.Box 126 (Safat) 13002
KUWAIT
TEL: 00 965 802929
Badie Studio & Stores
P.O. Box 62,
Doha, QATAR
TEL: 423554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952
SAUDI ARABIA
TEL: (03) 8643601
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
JORDAN
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
QATAR
UNITED KINGDOM
HUNGARY
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha’alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021)-2285-4169
OMAN
SPAIN
GREECE/CYPRUS
IRAN
Chahine S.A.L.
George Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
DAN Acoustic s.r.o.
Povazská 18.
SK - 940 01 Nové Zámky
TEL: (035) 6424 330
CZECH REPUBLIC
DISTRIBUTOR s.r.o
Voctárova 247/16
CZ - 180 00 PRAHA 8,
CZECH REP.
TEL: (2) 830 20270
Moon Stores
No.1231&1249 Rumaytha
Building Road 3931, Manama
339 BAHRAIN
TEL: 17 813 942
LEBANON
RUSSIA
SLOVAKIA
CZECH REP.
MIDDLE EAST
BAHRAIN
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
TEL: (04) 3360715
As of Oct. 1, 2007 (EDIROL-1)
*
0
4
9
0
1
0
1
2
-
0
1
*
04901012
1SX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement