PPM4-MK1 Leaflet

PPM4-MK1 Leaflet
Portable ISP
Programmer
High-Speed
Production
In-System
Programming
(ISP)and
Module
for Field-Service
Production applications
Selecting a project using the PPM4-MK1
programmer LCD display and 4 button keypad in
Standalone Mode
The Equinox PPM4-MK1 is a state-of-the-art Production ISP Programmer
designed for high-speed In-System Programming (ISP) of FLASH
microcontrollers and serial memory devices in a production environment. It
supports programming of devices by most interfaces including SPI, JTAG,
JTAG chain, SWD, I2C (2-wire) and UART Boot Loader. The fastest possible
programming times are guaranteed due to a combination of highly optimised
algorithms, local storage of Project Data and high slew-rate Line Driver Circuitry.
●● Production In-System (ISP) Programmer
●● Designed for high-throughput production programming environments
●● Supports In-system Programming (ISP) of many different programmable
microcontrollers and serial memory devices
●● Supports programming via SPI, JTAG, JTAG chain, I2C and UART
programming interfaces
●● Suitable for Standalone, Desktop or Programming Fixture use
●● Supports ‘Standalone’ operation - no PC required after programmer has
been configured
●● Capable of storing up to 64 completely independent ‘Standalone
Programming Projects’.
●● Interchangeable ‘I/O Driver’ and ‘I/O Connector’ modules
●● All programmer I/O lines are fully ESD and over-voltage protected
STANDALONE PROGRAMMING
PRODUCTION PROGRAMMING
FIRMWARE UPGRADEABLE
Power control:
Programming Interfaces:
●● Supports most ISP hardware
interfaces / protocols including JTAG,
ARM SWD (Serial Wire Debug), SPI, I2C,
XMEGA AVR PDI, ATtiny AVR TPI, ATtiny
AVR HV mode, 8051 UART Bootloader
●● Dedicated 2-wire I2C serial port
●● Interchangeable ‘I/O Connector
Modules’
●● User replaceable ‘Line Driver Circuit’
module (in case of damage)
●● Very fast programming speeds suitable for
high-throughput production environments
●● Individually configurable programmer I/O
pins
●● All programmer I/O lines are fully ESD and
over-voltage protected
●● Supports programming of target ICs
between 3.0 and 5.0V
●● Programmable frequency generator output
on SCK2 pin - supports external clocking
of AVR microcontrollers to speed up
programming
Control methods:
●● PC control via RS232, RS485 or USB port
●● Network up to 32 x ISPnano programmers
to a PC via RS485 bus
●● Standalone operation (no PC required)
●● Remote System Control e.g. PLC, ICT,
ATE - using ASCII (ATC) protocol
●● TTL Control Port for remote PLC control
Standalone Mode:
●● Programmable Target VCC
Supply: 3.0V - 5.0V @ 480 mA
●● Target voltage and current
Rear panel of
the PPM4
monitored by programmer
●● Fixed +12V Target VPP voltage generator
for ATtiny HV devices
●● Target Board short-circuit monitoring
●● Power supply input: 9.0V to 24.0V
Device support:
●● Atmel AVR SPI, AVR JTAG, XMEGA PDI,
ATtiny TPI, ATtiny HV microcontrollers
●● ARM microcontrollers (via JTAG or SWD
interface) - ARM7TDMI®, Cortex M0, Cortex
M3, Cortex M4
●● Selected 8051 FLASH microcontrollers
●● Serial EEPROM memories (SPI and I2C)
●● Serial FLASH memories (SPI)
●● Atmel / Adesto Serial DataFLASH™
●● Sigma - Z-Wave SOC’s and modules
Software (as standard):
●● EQTools - creates ‘Standalone
Programming Projects’
●● EDS - Development Mode for testing under
PC control
●● Upload Wizard - uploads projects to the
programmer
●● ASCII Text Communications protocol
(for remote control)
PASS BUSY FAIL
INSERT I/O CONNECTOR MODULE HERE
Additional features:
●● Backwards compatible with PPM3-MK2
●● Supports loading of up to 64 x
‘Standalone Programming Projects’
into the programmer memory (8 Mbytes
capacity)
●● Standalone project execution can be
triggered by local keypad, Fixture Lid
Switch, Target Sensing Circuit,
Remote Keypad or ASCII Text
Communications protocol (for
remote control)
●● Project selection via the keypad and
display (no PC required)
●● Single-button auto-program operation
allows repetitive execution of the selected
project
programmer
●● Remote Status LED Port
Typical applications:
●● Medium to high volume production
programming test fixtures
●● Standalone desktop programming
●● Remote PLC controlled programming
fixtures
I/O Connector Modules
Remote
Remote Status
Control Port
LED Port
I/O Connector Modules
PASS BUSY FAIL
External
PLC
System Contents:
The picture shows the typical contents of the
PPM4-MK1 production ISP programmer kit.
PASS BUSY FAIL
Remote
LED’s
Remote Control / Status Ports
Ordering information:
PPM4-MK1(UN)-
PPM4-MK1 Progarmmer Kit including AVR SPI, 8051 and Sigma 300 series
device support
PPM4-MK1 (EQ-SFM-MAX-V1.3) - PPM4-MK1 Progarmmer Kit including EQ-SFM-MAX-V1.3 Driver Module
EQ-SFM-1-
Standard I/O Driver Module (SFM) for PPM3-MK2 Programmer
EQ-SFM-MAX-V1.3-
High-speed I/O Driver Module (SFM) for PPM3-MK2 / PPM4-MK1 Programmer
Equinox Technologies reserves the right to change any information contained within this leaflet without prior notice. E&OE
Telephone: +44 (0)1942 841975
:
Equinox House, 217 Church Street Westhoughton, Bolton BL5 3SW United Kingdom
Fax: +44 (0)1942 844181 : Email: [email protected] : Web: www.equinox-tech.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement