Miele SAB100 ACCU NOVA Operating instructions
Miele SAB100 ACCU NOVA - The powerful, cordless stick vacuum cleaner for quick cleaning in between or for smaller areas. With up to 60 minutes of runtime and a variety of accessories, the cordless stick vacuum cleaner can be used flexibly and is suitable for all floor types. Thanks to the 3-stage filtration system with HEPA filter, it is also ideal for allergy sufferers. The electric floorhead with LED lights ensures optimal illumination of the suction area, even under furniture and in dark corners.
Advertisement
Advertisement
Operating instructions
Vacuum cleaner
S 4000
To prevent accidents and machine damage, read these instructions before installation and use.
UV
M.-Nr. 06 579 361
Contents
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Guide to the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before using the vacuum cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the included accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Turning the vacuum on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Opening the air inlet valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Transport and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Purchasing new dustbags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
When to change the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Replacing the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the exhaust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Exhaust filter change indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing the "SUPER air clean" filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the "ActiveAirClean" filter and the "Active HEPA" filter . . . . . . . . . . . . . 28
Replacing one type of filter with another . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
When to change the dust compartment filter (motor protection). . . . . . . . . . . . . . 30
Replacing the dust compartment filter (motor protection). . . . . . . . . . . . . . . . . . . 30
When to change the radio handpiece battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
How to change the radio handpiece battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
When to change the thread catcher pads of the SBD 450-3 floor tool and upholstery tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Replacing the thread catchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Servicing the floor roller of the SBD 450-3 floor tool . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
The manufacturer cannot be held responsible for any damage caused by non-compliance of these Important Safety Instructions.
WARNING-
To reduce the risk of fire, electric shock or injury:
Before using
Check the voltage rating of the vacuum cleaner before connecting the power cord to an electrical outlet.
Your power source should correspond with the voltage rating plate located on the underside of the vacuum. Use only household AC outlets. Never use DC power sources. If you are not sure of your home’s voltage supply, consult a qualified electrician. Connecting the vacuum cleaner to a higher voltage than indicated in these instructions may result in damage to the vacuum cleaner or injury.
To reduce the risk of electric shock, this appliance has a polarized plug
(one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not alter the plug in any way.
A damaged vacuum cleaner can be dangerous. Check the packaging, vacuum cleaner and accessories for any signs of damage.
Do not use a damaged appliance.
Do not use with a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors or submerged in water, bring it to a service center.
The electrical outlet must be fitted with a 15 A fuse.
3
4
IMPORTANT SAFETY INSTRUCTIONS
Use
Do not use on people or animals.
Do not use outdoors or on wet surfaces. Only dry surfaces should be vacuumed.
Use only as described in this manual.
Use only Miele recommended accessories.
The hose and the telescopic wand contain electrical wires. Do not use the vacuum cleaner if these parts are damaged in any way. Danger of electric shock!
The manufacturer cannot be held responsible for damage caused by non-compliance with these Important
Safety Instructions. This appliance is intended strictly for household use only.
This vacuum should not be used to entrap or retain any hazardous materials.
Do not allow the vacuum cleaner to be used as a toy. Close attention is necessary when used near children.
Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated surfaces.
Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
Do not handle the plug or vacuum with wet hands.
Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Floor attachments, accessories and wands must not be used at head level to avoid injury to eyes and ears.
Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
IMPORTANT SAFETY INSTRUCTIONS
Do not use the vacuum cleaner to pick up liquids, this could impair the electrical safety of the vacuum cleaner. Wait for freshly shampooed carpets to dry.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not vacuum items which are heavy, hard or have sharp edges.
They could cause a blockage and damage the appliance.
Do not vacuum toner dust. Toner, such as that used in printers and photocopiers can conduct electricity.
Unplug the vacuum when changing accessories, especially the Turbobrush and Electrobrush.
Do not turn on or attempt to operate the vacuum cleaner unless a dustbag, dust compartment filter and exhaust filter are in place. Use only genuine Miele double-layer dustbags and filters. See "Maintenance and care" for instructions on how to insert the dustbag and filters. If a dustbag has not been inserted, the dust compartment cover will not close. Do not use force!
Unwind the cord completely to aid the vacuum in dissipating heat.
A temperature limiter automatically switches off the vacuum cleaner if it gets too hot, see "Frequently asked questions".
On the underside of the vacuum handpiece is a metal insert designed to absorb static electricity.
Please make certain that your hand remains around this metal insert.
Do not leave the vacuum plugged in. Unplug it from the outlet when not in use and before servicing.
Do not place anything into the openings of the vacuum. Do not use if any openings are blocked; keep them free of dust, lint, hair, or anything that may reduce air flow.
This appliance is equipped with a power cord reel. Hold the plug when rewinding onto cord reel. Do not allow the plug to whip when rewinding.
5
6
IMPORTANT SAFETY INSTRUCTIONS
Accessory use
To avoid the risk of injury when vacuuming with a Miele
Electrobrush do not touch the rotating roller.
Use only attachments specified by
Miele. Do not use the blower to operate paint sprayers or similar devices that emit volatile or toxic vapors.
Monitor the dustbag change indicator and inspect all filters regularly. To ensure efficient suction, clean or replace them as necessary according to the operating instructions.
To guarantee safety, only use genuine
Miele dustbags, filters and accessories.
Miele vacuum cleaner bags are disposable and intended to be used only once. Do not attempt to reuse them.
Do not use the vacuum without an accessory attached. The rim could be damaged and injuries could result from sharp edges.
Maintenance and care
A damaged power cord must only be replaced with a genuine Miele cord by an authorized service agent.
Clean only with a dry or slightly damp cloth when disconnected from the power supply. Never submerge in water.
Repairs should only be performed by an authorized service agent in accordance with national and local safety regulations. Repairs by unqualified persons could be dangerous.
Disposal
Remove the battery from the radio handpiece and recycle it.
Before discarding an old vacuum cleaner, please cut off the power cord and render the plug useless.
Ensure the appliance presents no danger to children while being stored for disposal.
IMPORTANT SAFETY INSTRUCTIONS
FCC and Industry Canada information:
This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
,
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE
INSTRUCTIONS
7
Guide to the machine
Some models come standard with one of the following accessories, which are not shown in this figure.
– Turbobrush
– Cordless Rechargeable Powerbrush ACCU NOVA
A separate Operating manual of the respective accessory is supplied with the vacuum.
8
Guide to the machine a Handpiece (some models may include an air inlet valve) * b Suction power buttons + / – * c Standby switch * d LED * e Locking button f Accessory clip * g Telescopic wand release button * h Dust compartment lid release i Telescopic wand * j Dust bag k Carrying handle l Floor tool * m Transport/storage holder n Dust compartment filter (motor protection) o Exhaust filter * p Suction power selector * q Standby indicator * r Thermo indicator , * s Exhaust filter change indicator (Reset button) * t Power cord with plug u Cord rewind switch v Park-System w On / Off switch x Dustbag change indicator y Elbow z Suction hose
The features marked * may vary or not be available depending on your model.
9
Before using the vacuum cleaner
Attaching the suction hose
^ Insert the elbow into the suction socket until it clicks. Use the inlet guides to direct insertion.
Removing the suction hose
^ Press the release buttons at the sides of the elbow and lift the hose from the socket.
Connecting the handpiece and telescopic wand
^ Insert the handpiece into the telescopic wand until it clicks. Use the inlet guides to direct insertion.
^ To release the handpiece from the telescopic wand press the locking button (see arrow) and pull the handpiece away from the telescopic wand.
10
Before using the vacuum cleaner
Depending on your model, the vacuum will include one of the following telescopic wands:
– Fitted wand
(CDN only)
– Telescopic wand
– XXL telescopic wand
Inserting the fitted wand
Both sections of the telescopic wand have locating arrows to guide insertion.
Adjusting the telescopic wand
One section of the telescopic wand is inside the other and can be adjusted for comfortable vacuuming.
^ Press the telescopic wand release button (see arrow) to release the tubes and adjust to the desired height.
Adjusting the XXL telescopic wand
This telescopic wand consists of three sections which are height-adjustable.
^ Pull and extend the lower section of the wand, a, until it clicks. Press the release button if you want to retract the lower section again.
^ Press the adjustment button, b, to release the tubes and adjust to the desired height.
11
Before using the vacuum cleaner
Attaching the floor tool/brush
^ Insert the wand into the floor brush and twist until it locks with a click.
^ To release the floor brush from the telescopic wand, press the locking button (see arrow) and pull the wand out of the floor brush.
Observe the cleaning instructions of the floor manufacturer.
SBB 300-3 Floor brush
The floor brush is suitable for cleaning all hard flooring.
SBD 450-3 Floor tool
The floor tool is suitable for cleaning carpets, rugs, and hard surfaces. For flooring susceptible to scratches, use one of the special Miele floor brushes
(see "Optional accessories").
To clean carpets and area rugs
^ Press the foot switch marked ö.
To clean hard flooring
^ Press the foot switch marked ä.
Turbobrush / Cordless Rechargeable
Powerbrush ACCU NOVA
Some models have optional floor tools as accessories. Please refer to the separate operating instructions supplied with these brushes for instruction on use and maintenance.
12
Using the included accessories
The following accessories are included a Crevice nozzle b Dusting brush c Upholstery tool d Accessory clip for the respective included accessories e Filter frame
The filter frame is supplied only with those models which are fitted with an
"ActiveAirClean" or "Active HEPA" exhaust filter as standard. The filter frame is required to replace one of these filters with a "SUPER air clean" filter (see "Maintenance and care -
Replacing one type of filter with another").
Accessory clip
^ The accessory clip can be attached to the handpiece.
13
Using the included accessories
Floor brush SBB 300-3
(depending on model)
For cleaning all hard flooring.
Especially suitable for vacuuming niches and tight spaces.
Floor tool SBD 450-3
(depending on model)
The standard floor brush can be used for normal cleaning of carpets, rugs, hard surfaces, carpeted stairs, etc.
14
Crevice nozzle
For cleaning in folds, crevices and corners.
Using the included accessories
Upholstery nozzle
For cleaning upholstery, mattresses, cushions, curtains, covers, etc.
Dust brush with natural bristles
For cleaning moldings, decorative or carved items, etc.
The head of the dusting brush can be swiveled to attain the best cleaning position.
For dusting particularly delicate objects.
15
Operation
Power cord
,
Unwind the cable completely to aid the vacuum in dissipating heat.
Unwinding
^ Hold the plug and pull the power cord out to the required length
(maximum 18 ft / 5.5 m).
,
To reduce the risk of electric shock, the vacuum has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not alter the plug in any way.
Danger of overheating and damage.
Rewinding
^ Unplug the vacuum from the outlet.
^ Press the rewind switch briefly and the power cord will rewind automatically.
^ Press the rewind switch again to stop the rewinding.
^ Hold the plug so that it does not whip around when rewinding.
Turning the vacuum on and off
^ Press the On/Off switch.
16
Models with radio frequency controls
The operating state is shown by the
Standby indicator on the vacuum.
The vacuum can be switched to a standby mode during pauses.
^ Press the Standby button on the handpiece.
To turn the vacuum on again:
^ Press the Standby button on the handpiece. The vacuum cleaner turns on to the last selected power level.
^ Press – to turn the vacuum cleaner on at the lowest power level.
^ Press + to turn the vacuum cleaner on at the highest power level.
Every push of a button on the radio handpiece is displayed by the indicator light.
The vacuum can still be used if the battery in the radio handpiece is weak or not inserted at all.
^ Turn the vacuum on with the foot switch.
^ Press the Reset button.
The vacuum will operate continuously on the maximum suction power.
^ Turn the vacuum off with the foot switch.
Operation
17
Operation
While vacuuming
The vacuum cleaner can also stand on its end for vacuuming stairs, drapes etc.
,
To prevent static electricity your hand must touch the metal inlay on the underside of the vacuum handpiece. Be certain to continuously touch this inlay when vacuuming fine dust, flour or sawdust as these materials are more likely to create a static discharge. To further prevent static discharge while vacuuming, pull the vacuum along by the hose with one hand while continuing to hold the handpiece in the other hand.
Adjusting the suction
The symbols on the controls indicate what each setting is suitable for.
a curtains, lightweight fabrics b upholstery, cushions c thick pile carpets, rugs and runners d energy-saving, daily use e lightly soiled textured carpets f textured hard flooring, and intensive cleaning of carpets
18
The controls vary from model to model, and are described as follows.
Rotary selector
^ Turn the rotary selector to the desired suction power setting.
+ / – controls
Press the controls until the light bar above the desired suction power setting is illuminated.
^ Press the + control to select a higher setting.
^ Press the – control to select a lower setting.
+ / – at the radio handpiece
Press the controls until the desired suction power is shown in the vacuum display on the canister.
^ Press the + control to select a higher setting.
^ Press the – control to select a lower setting.
Every push of a button at the handpiece is displayed by the indicator light.
Operation
19
Operation
Opening the air inlet valve
(not available in models with radio handpiece)
The air inlet valve is designed to provide a quick, convenient reduction of suction power, e.g. when moving from a carpet to an area rug.
^ Open the air inlet valve far enough to reduce the power.
Opening the air inlet valve reduces the power to the tool being used.
20
Park-System
A Park-System has been designed to conveniently park the telescopic wand at the vacuum cleaner during pauses.
^ A special parking attachment is fitted to all floor brushes. Insert the lower clip of the floor brush into the slot on the end of the vacuum cleaner from above.
Transport and storage
Transport and storage
^ For easier transportation and storage
– stand the vacuum cleaner vertically.
– insert both clips of the floor brush into the two point holder on the side of the vacuum.
– insert one part of the telescopic wand into the other (depending on model).
21
Maintenance and care
,
Turn off the vacuum and unplug it from the outlet before performing any maintenance work.
If in use turn the Cordless
Rechargeable Powerbrush ACCU
NOVA off.
Purchasing new dustbags and filters
Replacement dustbags and filters can be purchased from your local Miele
Dealer.
The Miele filter system consists of three filters which must be replaced from time to time to ensure efficient suction.
– Dustbag
– Exhaust filter
– Dust compartment filter
(motor protection)
Use only Miele dustbags with the
Miele quality signet and original
Miele filter. This ensures optimum performance of the suction power and also ensures that the bag is used to capacity.
The use of non-Miele dustbags could cause damage to the vacuum cleaner.
Which dustbags and filters are the right ones?
Order original Miele dustbags with the letters F/J/M .
A "SUPER air clean" exhaust filter and a dust compartment filter are supplied with every box of Miele dustbags. If you wish to purchase exhaust filters or dust compartment filters separately, please quote the model number on the data plate located underneath the appliance.
You can replace the exhaust filter supplied with the vacuum cleaner with one of the other types of filters (see
"Optional accessories").
22
Maintenance and care
When to change the dustbag
Change the dustbag when the colored marker in the dustbag change indicator fills the display.
The dust bags are disposable and intended to be used only once. Do not attempt to reuse.
Checking the dustbag change indicator
Perform this test with the SBD 450-3 floor tool only, since other attachments can affect the function of the dustbag change indicator. If your vacuum cleaner is equipped with the
SBB 300-3, the test cannot be performed.
^ Attach the floor tool to the vacuum cleaner.
^ Turn the vacuum cleaner on and select the highest power setting.
^ Lift the floor tool slightly off the floor. If the marker completely fills the indicator window, the dust bag needs to be changed.
How the dustbag change indicator works
The dustbag change indicator is designed to show when the bag is full of common household dust and to measure the amount of air flow through the dustbag. Normal household dust is a mixture of dust, hair, carpet fluff, threads, sand, etc.
However, if fine dust, such as drill dust, sand, plaster or flour is vacuumed, the pores of the dustbag will become blocked. The marker will indicate that the bag is "full" even when it is not. The dustbag should be changed because the suction power is greatly reduced.
If the bag is bulging with pet fur, hair, carpet fluff, etc., the indicator may not register "full". This is because the air flow of the dustbag may still be high enough not to activate the marker to show maximum. The dustbag should still be changed.
23
Maintenance and care
Replacing the dustbag
^ Open the dust compartment lid.
^ Grasp the collar by the two finger holes and pull it out of the dustbag holder.
The dustbag has a flap which closes automatically to prevent dust from escaping when it is removed.
^ Insert the new dust bag as far as it will go into the dustbag holder. Do not unfold the dustbag when taking it out of the box. Keeping it folded will prevent it from getting caught when the dust compartment lid is closed.
^ Close the dust compartment lid until it clicks into place. Take care not to catch the dust bag in the lid.
,
A empty-operation-barrier will block the dust compartment lid from closing if no dustbag is inserted or if it is not inserted all the way.
Do Not Use Force!
24
Replacing the exhaust filter
Depending on model, the vacuum cleaner will be equipped with one of the following exhaust filters: a SUPER air clean filter b ActiveAirClean filter c Active HEPA filter
"SUPER air clean" filter
A "SUPER air clean" filter is supplied with every box of Miele dustbags. It should be replaced each time a new box of bags is started.
"ActiveAirClean" or the "Active
HEPA" filter
An "ActiveAirClean" or "Active HEPA" filter should be changed approximately once a year. Change the filter sooner if it is obviously soiled or no longer effective.
It is helpful to note the date directly on the filter as a reminder for when to next change it. See "Optional Accessories" for filter descriptions.
Maintenance and care
25
Maintenance and care
Exhaust filter change indicator
Some models are equipped with an exhaust filter change indicator (Reset button) which is designed to alert the user when to change the
"ActiveAirClean" or "Active HEPA" filter.
The indicator will light after about
50 hours of operation which is equivalent to about a year of average use. The vacuum cleaner can still be used with the exhaust filter indicator lit.
However, the suction power will be reduced as will the effectiveness of the filter if it is not replaced.
If a SUPER air clean filter, a , is being used, the filter change indicator can be disregarded but should be reset when it does light. The indicator goes out when the reset button is pressed.
You can replace the exhaust filter supplied with the vacuum cleaner with one of the other types of filters (see
"Optional accessories").
26
Replacing the "SUPER air clean" filter
^ Open the dust compartment lid.
^ Open the filter frame and remove the used "SUPER air clean" filter with the clean corner (see arrow).
Maintenance and care
^ Insert the new filter.
^ Close the filter frame.
^ Close the dust compartment lid firmly until it clicks into place.
27
Maintenance and care
Replacing the
"ActiveAirClean" filter and the
"Active HEPA" filter
^ Open the dust compartment lid.
^ Remove the exhaust filter.
^ Insert the new filter.
^ Close the dust compartment lid firmly until it clicks into place.
Resetting the filter change indicator
The filter change indicator (Reset button) must be reset each time the filter is replaced. To do this, the vacuum cleaner must be plugged in.
^ Press and hold the filter change indicator light until it goes out.
The display is now reset.
28
Replacing one type of filter with another
1. If you wish to replace the a SUPER air clean filter with the b ActiveAirClean filter or the c Active HEPA filter, you must remove the filter frame before inserting the new filter.
2. If you use SUPER air clean filter a you must insert it into the filter frame.
* Filter frame - see "Using the included accessories".
The ActiveAirClean filter can be used instead of the Active HEPA filter and vice versa without any changes.
Remember to reset the filter change indicator with the Reset button after every filter change. The indicator will go out when the reset button is pressed.
Maintenance and care
29
Maintenance and care
When to change the dust compartment filter (motor protection)
Replace the dust compartment filter every time you start a new box of dustbags. A dust compartment filter is supplied with each box of Miele dustbags.
Replacing the dust compartment filter (motor protection)
^ Open the dust compartment lid.
^ Open the filter frame, remove the old filter and replace with a new one.
^ Close the filter frame.
When to change the radio handpiece battery
Every 18 months
Keep a 3 V lithium (CR 2032) battery handy.
How to change the radio handpiece battery
^ Lift the battery compartment lid and take the old battery out. Please recycle.
^ Replace the battery with a new one.
Pay attention to the polarity.
^ Close the battery compartment.
30
When to change the thread catcher pads of the SBD 450-3 floor tool and upholstery tool
The thread catcher pads on the bottom of the SBD 450-3 floor tool and the upholstery tool should be checked occasionally. Replace the pads if they appear worn.
Maintenance and care
Replacing the thread catchers
^ Use a knife or similar object to remove the thread catchers from the slots.
^ Insert the new thread catchers.
Servicing the floor roller of the
SBD 450-3 floor tool
^ Use a coin to release the roller pin and take it out, a.
^ Push and take out the roller axle, b.
^ Take out the roller, c.
^ Remove all threads, hair, etc. and reassemble the parts in the reverse order.
Spare parts are available from your
Miele dealer or from Miele.
31
Cleaning and care
,
Turn off the vacuum and unplug it before performing any maintenance work.
If in use turn the Cordless
Rechargeable Powerbrush ACCU
NOVA off.
Vacuum cleaner and accessories
External surfaces of the vacuum cleaner and accessories can be cleaned with a slightly damp cloth or with a cleaner suitable for plastics.
,
Do not use abrasive, glass or all purpose cleaners! They will damage the surface.
Dust compartment
The dust compartment can, if necessary, be cleaned using a dry cloth, dusting brush or a second vacuum to suck out any
Monitor the change dustbag indicator and inspect all filters regularly. Clean or replace them when necessary according to these Operating
Instructions.
,
Do not submerge the vacuum in water! If moisture gets into the appliance there is the risk of an electric shock.
32
Some models have a warning light
, which comes on to indicate overheating.
If the vacuum has overheated the temperature limiter automatically turns the vacuum off. Some models also have a warning light , to indicate that the vacuum has overheated.
This can occur if, for instance, large articles block the suction tube or when the filter bag is full or contains particles of fine dust. A heavily soiled exhaust or dust compartment filter can also be the cause of overheating. Turn off the vacuum cleaner using the On/Off switch.
Unwind the full length of the power cord. Allow the vacuum to cool down for 30 minutes.
After sales service
In the event of a problem that you can not fix yourself, please contact the
Miele Service Department.
Frequently asked questions
33
Optional accessories
Each model may be accessorized with one or several of the following tools.
Electrobrush
SAB 100-3
The rechargeable battery brush is intended for intensive cleaning and restoring of thick pile carpeting. It is particularly suitable for cleaning and restoring crushed carpet pile of floor coverings subject to hard wear, especially in high traffic areas.
Observe the cleaning instructions of the floor manufacturer.
Turbobrush
STB 205-3
The Turbobrush is intended for cleaning short to medium pile carpeting. It is mechanically driven by the suction power of the vacuum. In addition to dust particles it also removes stubbornly adhered threads, hairs, fluff, etc.
Observe the cleaning instructions of the floor manufacturer.
Hand Turbobrush
STB 101
The Hand Turbobrush is intended for vacuuming upholstery, mattresses, car seats, carpeted stairs and other areas inaccessible with the standard
Turbobrush.
34
Hard floor brush
SBB 235-3
To vacuum sturdy hard floors, e.g. tiles and stone floors.
Optional accessories
Parquet floor brush
SBB Parquet-3
Special brush with natural bristles intended for cleaning parquet and laminate floors, especially those susceptible to scratching.
35
Optional accessories
Universal brush
For dusting books, shelves, etc.
Dust brush with natural bristles
For dusting particularly delicate objects.
Radiator brush
(only usable with the crevice nozzle)
For cleaning radiators, narrow shelves or crevices.
36
Mattress tool
For cleaning deep crevices, mattresses and upholstery.
Optional accessories
Crevice nozzle 12" (300 mm)
For cleaning in folds, crevices, corners, etc.
37
Optional accessories
Hygiene lock with active charcoal
Minimizes the escape of dust and odor when the hose is removed for transport or storage.
The cap can be fastened to the hose during vacuuming.
Flexible Hose Extender
To extend the hose by 5 ft. (1.5 m).
The hose adapter is inserted between handpiece and hose.
The flexible hose extender can only be used with a non-electric hose.
38
MicroSet
This set is specially designed for cleaning small objects and difficult to reach areas (such as PC keyboards, stereo equipment, carved furniture and ornaments, models, etc). Contents:
– Micro hose with combi nozzle
(crevice nozzle and dust brush)
– Micro dust brush
– Micro crevice nozzle
– Extension
CarClean Set Plus
Specially designed for cleaning car interiors.
Accessory set consists of:
– Hand Turbobrush
– Microhose with combi nozzle
– Crevice tool 12" (300 mm)
– Accessory carrying case, 10 ft (3 m) long suction hose and holder.
Optional accessories
39
Optional accessories
ActiveAirClean filter
A special active charcoal filter which absorbs odors from the dust collected in the dustbag. The "ActiveAirClean" filter can be used in place of the
"SUPER air clean" filter. There is no difference in the fine dust performance of the "ActiveAirClean" and the "SUPER air clean" filter.
Active HEPA Filter
The "Active HEPA" filter combines activated charcoal and HEPA filtration in one. The active charcoal layer absorbs odors from the dust collected in the dustbag. Vacuum cleaners equipped with this exhaust filter are particularly suitable for allergy sufferers and those concerned with a high level of hygiene because of its ability to trap respirable particles and allergens.
40
Caring for the environment
Disposal of the packing materials
The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable.
Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. These items pose a danger of suffocation.
Disposing of the dustbag and filters
Genuine Miele dustbags and filters are made of environmentally friendly materials. They can be thrown out with the household trash provided the vacuum has been used only for normal household dust.
41
42
43
All rights reserved/1406 M.-Nr. 06 579 361 / 00 en - US
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement