OM, Flymo, Minimo, 96328000100, 2004-02, Electric Lawn Mower Air

TIO
A
M
R
N
NFO
I
T
TA N se
R
nce
O
e
r
P
u
e
f
e
I M befor
re re
u
t
d
u
a
f
Re
for
n
i
a
t
& re
For all customer enquiries or for replacement parts, contact:-
☎
01325 300303
www.flymo.com
[email protected]
1
Carton Contents
handle
bolt
nut
cable clips
plastic
wing
knob
handle tube
electric
cable with
moulded
on plug
bolt
motor cover
fixing pin
nut
plastic wing
knob
hood
instruction
manual
fixing pin
plastic cutters
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct
Telephone :
01325 300303
Fax :
01325 318193
Safety Precautions
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious
injury to the operator and others, the warnings and safety instructions must be followed to
ensure reasonable safety and efficiency in using this lawnmower. The operator is responsible
for following the warning and safety instructions in this manual and on the lawnmower.
Explanation of Symbols on the Minimo
Warning
Keep bystanders away. Do not
mow whilst people especially children or pets are in the mowing
area.
Read the user instructions carefully to make sure you understand all
the controls and what they do.
Do not mow in the rain or leave
the lawnmower outdoors while
raining
Switch off! Remove plug from
mains before adjusting, cleaning
or if cable is entangled or damaged. Keep the cable away from
the plastic cutters.
The use of eye protection is recommended.
2
General
1. Never allow children or people unfamiliar with
these instructions to use the mower. Local regulations may restrict the age of the operator.
2. Only use the lawnmower in the manner and for the
functions described in these instructions. Only use
this lawnmower for cutting grass.
3. Never operate the lawnmower when you are tired,
ill or under the influence of alcohol, drugs or medicine.
4. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
1. The British Standards Institute recommend the use
of a Residual Current Device (R.C.D.) with a tripping current of not more than 30mA. Even with a
R.C.D. installed 100% safety cannot be guaranteed
and safe working practice must be followed at all
times. Check your R.C.D. every time you use it.
2. Before use, examine cable for damage, replace it if
there are signs of damage or ageing.
3. Do not use the lawnmower if the electric cables are
damaged or worn.
4. Immediately disconnect from the mains electricity
supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the
electrical supply has been disconnected. Do not
repair a cut or damaged cable. Replace it with a
new one.
5. Your cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your mower.
6. Keep cable away from lawnmower, always work
away from the power point mowing up and down,
never in circles.
7. Never carry the product by the cable.
8. Never pull on the cable to disconnect any of the
plugs.
9. Do not pull cable around sharp objects.
10. Always switch off at the mains before disconnecting any plug, cable connector or extension cable.
11. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a damaged cable, replace it with a new one. Use only
Flymo replacement cable.
12. Always wind cable carefully, avoiding kinking.
13. Use only on AC mains supply voltage shown on
the product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to any part of the product.
Preparation
1. While using your product always wear substantial
footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones,
bones, wire and debris; they could be thrown by
the plastic cutters.
3. Before using the machine and after any impact,
check for signs of wear or damage and repair as
necessary.
4. Replace worn or damaged plastic cutters together
with their fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good artificial light.
2. Avoid operating your lawnmower in wet grass,
where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and
wear non-slip footwear.
5. Mow across the face of slopes, never up and
down.
6. Exercise extreme caution when changing direction
on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous.
Do not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you could
trip.
9. Never cut grass by pulling the mower towards you.
10. Switch off before pushing the mower over surfaces
other than grass.
11. Never operate the lawnmower with damaged
guards or without guards in place.
12. Keep hands and feet away from the cutting means
at all times and especially when switching on the
motor.
13. Do not tilt lawnmower when the motor is running,
except when starting and stopping. In this case,
do not tilt more than absolutely necessary and lift
only the part which is away from the operator.
Always ensure that the hand is in the operating
position before returning the appliance to the
ground.
14. Never pick up or carry a mower when it is operating or still connected to the mains supply.
15. Remove the plug from the mains :
-
-
before leaving the mower unattended for any
period;
before clearing a blockage;
before checking, cleaning or working on the
appliance;
if you hit an object. Do not use your lawnmower until you are sure that the entire lawnmower is in a safe operating condition;
if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutters and impeller
specified for this product.
4. Be careful during adjustment of the lawnmower to
prevent entrapment of the fingers between moving
plastic cutters and fixed parts of the machine.
3
CABLES - IMPORTANT
• Use only 1.00mm2 size cable up to 30 metres length
maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
THE MINIMO IS SUPPLIED WITH AN ELECTRIC MAINS
CABLE WIRED DIRECTLY INTO THE PRODUCT.
1. Flymo Mains Cables and Extension Cables are available
from your local Electrolux Outdoor Products Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Electrolux Outdoor
Products Approved Service Centre for further information on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulated
to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
E
L
BLACK
OR N
BLUE
4.
5.
6.
7.
F
U
S
E
RED
OR
BROWN
The wires in the mains lead are coloured in accordance with the following code:
BLUE
NEUTRAL
BROWN LIVE
The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N'
or coloured BLACK.
The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED.
It is important that the outer sheath is clamped correctly into the 3-pin plug.
If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
A 13 Amp fuse must be fitted to the Mains Plug.
The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution.
If your product is hard wired i.e. non-detachable
mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor
Products Approved Service Centres which can be
found in your local Yellow Pages.
Assembly Instructions
A
handle
bolt
wing knob
handle
tube
B
nut
handle
tube
pegs
motor cover
nut
wing knob
Assembly of handle tube to motor cover (B)
1. Locate the the handle tube onto the two pegs in the
neck of the motor cover.
2. Insert the bolt through the motor cover and the centre
hole of the handle tube.
3. Insert the nut into the wing knob.
4. Secure with the wing knob.
bolt
C
hinge
fixing pin
Assembly of handle to handle tube (A)
1. Insert the handle tube into the handle as illustrated,
ensuring the handle is in an upright position
2. Insert the nut into the wing knob.
3. Secure with the bolt and wing knob.
bracket
Assembly of motor cover to hood (C)
• Note:- Ensure the handle is to the rear of the
hood when the motor cover is fitted.
1. Align the hole in the hinge of the motor cover with the
holes in the bracket on the hood. Secure by inserting
the fixing pin and pressing firmly until a click is heard.
2. Repeat on the other side.
3. Secure the motor cable into the location points on the
fixing plate, and to the handle tube with the cable
clips provided.
4
Starting and Stopping
Starting
1. Hold as illustrated in Fig D.
2. To start, press the lock-off button down, whilst
pressing the lock-off button, squeeze the
switch lever.
Stopping
1. To stop your lawnmower, release the switch
lever.
D
Lock-off button
Switch lever
Adjusting the Cutting Height
E
HIGHEST
This symbol visible
F
LOWEST
This symbol visible
• THERE ARE 2 CUTTING HEIGHTS (E & F)
• Height of cut is adjusted by turning
over the cutting head.
• Disconnect from the mains electricity supply and wait until the cutting head has
stopped rotating. Turn your lawnmower
upside down.
• To Remove the Cutting Head and Fan (G)
Hold the fan firmly and twist the cutting
head anti-clockwise as illustrated. Hold
the cutting head in the centre and remove
as illustrated Hold fan in the centre and
remove as illustrated
• Inspect for damage and clean as necessary before replacing the fan and the cutting head
G
1
3
2
H
• To Refit the Fan and the Cutting Head (H)
Replace the fan as illustrated. Replace
the cutting head, adjusting the height of
cut as required. Hold the fan firmly and
twist the cutting head clockwise, as illustrated.
• IMPORTANT
ENSURE FAN AND CUTTING HEAD
ARE CORRECTLY LOCATED
1
3
2
5
How to Mow
1. Start mowing the edge of the lawn nearest to the power point so that the cable is laid out on the lawn you have
already cut.
2. Mow twice a week in the growing season, your lawn will suffer if more than one third of its length is cut at one
time.
Do not Overload your Lawnmower
Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the
motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick
grass, a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height.
Cutting System Maintenance
J
cutting
head
plastic
cutters
fan
hood
K
Remove cutter..
..replace cutter
• Always handle the plastic cutters with care sharp edges could cause injury. USE GLOVES.
Checking your Cutting System (J)
• The cutting system must be kept in good condition
and inspected before and after use.
• Disconnect from the mains electricity supply and
wait until the cutting head has stopped rotating.
Turn your lawnmower upside down.
1. Visually check cutting head for wear. Replace if
damaged.
2. Visually check plastic cutters for wear and replace
when necessary.
3. Plastic cutters should be straight. Replace if bent
or twisted.
Replacing Plastic cutters (K)
• Use only genuine Flymo replacement plastic cutters specified for this product. These are available from all Electrolux Outdoor Products Service
Centres and major retail outlets.
• Plastic cutters must be replaced in pairs to retain
balance.
• Two plastic cutters of the same type should be fitted.
• Never fit a steel bar blade to this product.
• To Replace Plastic Cutters
• Disconnect from the mains electricity supply and
wait until the cutting head has stopped rotating.
Turn your lawnmower upside down.
1. Push plastic cutter towards centre of cutting disc.
Lift plastic cutter away from cutting head.
2. If the plastic cutter is broken during use - lever
cutter out of the slot, and dispose of carefully.
3. Fit new plastic cutters into the slots at each side
of the cutting head and pull into place.
• IMPORTANT:ENSURE PLASTIC CUTTERS ARE
CORRECTLY LOCATED.
Caring for your Lawnmower
L
• It is very important that you keep your lawnmower clean. Grass clippings left in any of
the air intakes or under the hood could
become a potential fire hazard
Cleaning (L)
1. Remove grass from under the hood with a piece
of wood or similar.
2. Using a soft brush - remove grass clippings from
all air intakes.
3. Remove the cutting head, (see fig G), to gain
access to the fan and clean with a soft brush.
4. Wipe over the surface of your lawnmower with a dry cloth.
• IMPORTANT
Never use water for cleaning your lawnmower.
Do not clean with chemicals, including petrol, or
solvents - some can destroy critical plastic parts.
6
Caring for your Lawnmower
At the End of the Mowing Season
1. Replace plastic cutters, bolts, nuts or screws, if
necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter
thoroughly and carry out any service or repairs
required.
4. Make sure that the electric cable is coiled properly.
N
M
Carrying your Lawnmower
Hold as illustrated in Figure M. Ensure the cutters
are facing away from you.
Storing your Lawnmower
Store in a dry place where your lawnmower is protected from damage.
Your product can be stored in a hanging position.
• The back of the handle has a hanging slot for
storing the product on the wall.
1. Hang the product from a hook or suitable screw as
illustrated in Figure N.
Fault Finding Hints
Fails to Operate
1 Is the Power Turned On?
2 Check the fuse in the plug, if blown replace.
3 Fuse continues to blow?
Immediately disconnect from the mains electricity supply and consult your local approved
Service Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See Adjusting the
Cutting Height.
4. If poor flotation persists?
Disconnect from the mains electricity supply
and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Replace broken or missing plastic cutters.
3. Check plastic cutters and cutting head are fitted correctly and securely located.
4. If vibration persists?
Immediately disconnect from the mains electricity supply and consult your local approved
Service Centre.
Service Recommendations
1. We strongly recommend that your product is
serviced at least every twelve months, more
often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most
Electrolux Outdoor Products stockists.
4. Your product is uniquely identified by a silver and
black product rating label.
5. If you have a problem with your machine contact
your local Approved Service Centre ensuring you
have full details of your product as described on the
product rating label.
6. Should it be necessary for work to be carried
out by your Service Centre, it is important to
take your complete machine including cable and
any extension cables used.
A network of specialist dealers can be found in your local
Yellow Pages. To obtain service on your Flymo product
simply telephone or visit your local Service Centre. Should
you require service under the terms of our guarantee the
Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare
Parts. NOTE: Our Service Repairers act on their
own behalf and are not empowered to commit or
legally bind Electrolux Outdoor Products in any
manner whatsoever.
Environmental Information
Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life.
• Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal information.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor
Products, through its Authorised Service Repairers will
effect the repair or replacement to the customer free of
charge providing:
(a) The fault is reported directly to the Authorised
Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or
faulty adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Electrolux Outdoor Products.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the
country for which it was specified.
(i) The machine has not been used commercially.
*
This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore
it is important that you read the instructions contained
in this Operator's Manual and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged plastic cutters
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid warranty claim: Plastic Cutters, Electric Mains cable.
* Caution!
Electrolux Outdoor Products does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Electrolux Outdoor Products, or by the
machine having been modified in any way
EC Declaration of Conformity
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP. Certify that the Product:Category........ Electric Lawn Trimmer
Make.............. Electrolux Outdoor
Products
Conforms to the specifications of Directive
2000/14/EEC
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using directive
81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at
operator position under free field semi anechoic chamber conditions was :-
Type of Cutting Device.... Plastic Cutter
Identification of Series......See Product Rating Label
Conformity Assesment Procedure....ANNEX VI
Notified Body.................... I.T.S.. Cleeve Road, Leatherhead,
Surrey, KT22 7SB. England
Other Directives:-............. 98/37/EEC, 89/336/EEC, 73/23/EEC
& applicable standards:- EN786, IEC60335-1, EN60335-2-91, EN610003-2, EN61000-3-3, EN55014-1, EN55014-2
Electrolux Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
a guide. The maximum weighted root
mean square value of vibration recorded at
operator’s hand position was:-
Type...................................................... Minimo
Width of Cut.......................................... 28cm
Speed of Rotation of Cutting Device.... 7,500 RPM
Guaranteed sound power level............ 94 dB (A)
Measured Sound Power Level............. 94 dB (A)
Level..................................................... 81.6 dB (A)
Value.................................................... 2.12 m/s2
Weight.................................................. 5.4 kg
Newton Aycliffe, 21/01/2004
M. Bowden,
Research & Development Director
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
www.electrolux.com/flymo
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor
Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries.
© Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ
Registered number 974979 England
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products
(such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
5119359-04