Luxul XWS-1310 Quick Install Manual

Add to my manuals
8 Pages

advertisement

Luxul XWS-1310 Quick Install Manual | Manualzz

QUICK INSTALL GUIDE

Wireless Controller System with Standard-Power 300N

Access Points

XWS-1310

System Includes:

„

One: XWC-1000 Wireless Controller

(Includes Rack Mount Kit and Power Cord)

„

Three: XAP-310 300N Access Points

„

One: 5-Port PoE Switch

READ ME FIRST - AP COMPATIBILITY

The Access Points included in this XWS-1310 Wireless Controller Kit are ready for setup.

If you don’t plan to use the Wireless Controller to manage any older or previously

-installed APs, you can skip to the next section titled, “Before You Begin Installation”.

If you are using separately-purchased Luxul APs or installing a

Wireless Controller into an existing Luxul deployment, you may need to manually upgrade the AP firmware before installing the Wireless Controller. Luxul APs running firmware version 5 or later are Controller-compatible and can be used with the

Controller as-is. When purchasing Luxul APs for use with the

Wireless Controller, look for an orange “Version 5 Firmware” sticker on the box to avoid the manual upgrade process.

O

L

R

R

E

A

TR

• C O N

D Y

VERSIO

N 5

ON

FIRMWA

C

RE

T R

O

DY

E

A

L

L

X

Access Point Compatibility: The XWC-1000 Wireless Controller is compatible with the following Luxul AP models: XAP-310, XAP-1210, XAP-1230, XAP-1500.

Access Point Upgrade Instructions:

c c Caution:cItciscnotcpossiblectocdowngradecthecAPcfromcfirmwarecversionc5,cc socupgradeconlycifcyoucareccertaincyoucdon’tcwantctocgocback.

1. Make sure the XWC-1000 Wireless Controller is disconnected from the network or powered off during the AP upgrade process.

2. Use your computer to download the firmware file for your AP from luxul.com/firmware-updates

3. Open the APs web interface by entering the IP address of the AP in your computer’s browser and select Administration >> Firmware Update

4. Click the Browse button and select the firmware file you downloaded, then click Open

5. Click the Upgrade button. You should now see a status indicator to let you know the firmware upgrade is in progress.

6. Once the power LED starts blinking, close the browser used to access the

APs web interface.

7. Once the power LED stops blinking, open a new browser window and re-enter the

IP address of the AP. Restore the APs factory default settings by using the web interface or the Factory Default button on the AP. The AP is compatible with the

XWC-1000 Wireless Controller only after it is restored to factory default condition.

8. The AP is now compatible with the Wireless Controller. Power down the AP until the Controller Setup Wizard instructs you to apply power to the AP.

Repeat this process for any other APs which require a manual firmware upgrade and that you wish to manage with the XWC-1000 Wireless Controller.

BEFORE YOU BEGIN INSTALLATION

X

Access Point Firmware: If you are using APs other than those included in this kit, please refer to READ ME FIRST - AP COMPATIBILITY on the previous page.

X

Controller Setup Sequence: Be sure to setup the XWC-1000 Wireless Controller

BEFORE powering up the APs. Once logged into the Wireless Controller, the Setup

Wizard will prompt you when it is time to add the APs to the network. A DHCP server is required on the network.

X

Accessibility: Once an Access Point is controlled by the XWC-1000 Wireless

Controller, the web interface on the AP is no longer enabled. Conversely, if an AP confi guration is managed via its web interface, communication with the XWC-1000

Wireless Controller will be disabled. To change an AP from Controller-managed to standalone (or the reverse), restore the AP to Factory Default.

X

Firmware Updates: The XWC-1000 Wireless Controller automatically checks for fi rmware updates of Controller-compatible APs and the Wireless Controller itself, but requires Internet access to do so. The Wireless Controller will still operate without Internet access, but fi rmware updates will not be available.

Physical Installation

X

Connecting Devices: The XWC-1000 Wireless Controller simply connects to the network. The XAP-310 APs connect to the network via the included PoE Ethernet switch (or other 802.3af/at switch).

LAN

AP

AP

PoE

LINK/ACT

POWER

LAN

PoE

Switch

AP

Wireless Controller

X

Access Point Placement: You may need to experiment with AP placement to optimize the roaming experience. Place APs to ensure adequate coverage, but not so far apart that there is no signal overlap. Adjacent APs should overlap enough that the client device has a good connection to the AP to which it is currently attached, but also sees the next-nearest AP. Ideally, roaming clients should see signal strength of two overlapping APs in the range of -60 to -70 dBm at the midway point between two

APs. To learn more about AP placement, visit luxul.com/ap-placement .

Ideally, roaming clients should see signal strength of two overlapping

APs in the range of -60 to -70 dBm at the midway point between two APs n c Note:cConsidercusingcEkahaucHeatMapperctocassistcwithcthiscprocess,cavailablec fromc www.ekahau.com

.cLuxulcalsocofferscancinformativec“How-To”cvideoconc

HeatMappercatc luxul.com/how-to-videos .

WIRELESS CONTROLLER SYSTEM KIT SETUP

1. Use an Ethernet cable to plug the XWC-1000 Wireless Controller into the network.

Do not connect any APs to the network yet.

n c Note:cBecsurecacDHCPcserverciscpresentconcthecnetworkcandcthatcallcLuxulcAPscandc thecXWC-1000cWirelesscControllercwillcsharecthecsamecsubnet.cIfcyourcnetworkc

usescac192.168.0.XcIPcaddresscscheme,cyoucarecreadyctocstartcthecsetupcprocess.cIfc

not,cyoucwillcneedctocmanuallycchangecthecIPcaddresscofcyourccomputerctocbecablec tocconficgurecthecXWC-1000cWirelesscControllercsocthatcitcisconcthecsamecsubnetcasc yourcnetwork.cForchelpcsettingcthecIPcaddresscofcyourcparticularcoperatingcsystem,c visitc luxul.com/ip-addressing.

2. To access the Setup Wizard, open your web browser and enter the Wireless

Controller’s default 192.168.0.19 IP address in the address fi eld. Log in to the Wireless

Controller using the default user name and password:

Default IP: 192.168.0.19

Username: admin

Password: admin n c Note:cIfcthereciscanothercdeviceconcthecnetworkcalreadycusingcthec192.168.0.19c address,cyou’llcneedctoceitherctemporarilycdisconnectcorcreconficgurecthatcotherc device,corcmanuallycconficgurecthecWirelesscControllercwithcacdifferentcaddressc oncacseparatecisolatedcnetwork.

3. Follow the built-in Setup Wizard in the Wireless Controller. The Wizard will direct you to power the APs on at the appropriate time and walk you through completing the setup.

t c Smart Tip:cForcmorecinformationconcsetupcandcconficgurationcbestcpractices, visitc luxul.com/smart-tips .

RESETTING THE CONTROLLER

X

Reset/Reboot: Use a paperclip to press and release the reset button on the front panel of the Controller to force it to reboot. The LEDs will go dark once the button is released, then blink slowly while the controller boots.

X

Restore Factory Defaults: To restore the controller to Factory Default confi guration, press and hold the reset button for at least 5 seconds. The System

LED will blink quickly to indicate that the Controller is returning to Factory Default confi guration, go dark for a few seconds, then blink slowly while the controller reboots.

X

Normal Operation: When the controller is operating normally, the System LED will blink like a heartbeat, i.e. blink-blink-dark.

LEGAL AND REGULATORY INFORMATION

No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.

FCC ID: W59XAP310

IC: 8584A-XAP310

Regulatory Compliance

The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. This equipment also complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

Unauthorized antennas, modifications, or attachments could cause damage and may violate regulatory approvals. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment.

The equipment version marketed in the U.S. is restricted to usage of channels 1-11 only.

Health and Safety Recommendations

X Warnings for the use of Wireless Devices: Please observe all warning notices with regard to the usage of wireless devices

X Potentially Hazardous Atmospheres: You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles

(such as grain, dust, or metal powders).

X Safety in Hospitals: Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected.

RF Exposure Guidelines

X Safety Information: The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices.

X Warning, Exposure to Radio Frequency (RF) Radiation: The radiated output of this device is below the

FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized.

X The end user must avoid any extended human RF exposure directly in front of the device, up to a distance of 20cm, when unit is on.

X When servicing the equipment and selecting a location for the antennas, it is important to note that a minimum distance of 20cm is required between personnel and the device or antenna to comply with the radio frequency exposure limit.

X The antenna used for this transmitter must be installed to provide a separation distance of at least

20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

The following safety precautions should be observed:

X Do not touch or move the antenna while the unit is transmitting or receiving.

X Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting.

X Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio.

FCC Statement—Wireless FCC 2.4GHz 802.11bgn

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

X Reorient or relocate the receiving antenna.

X Increase the separation between the equipment and receiver.

X Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

X Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that this Luxul

XAP-310 is in compliance with the essential requirements and other relevant provisions of

Directive 1995/5/EC.

For a copy of this report send a self addressed stamped envelope to:

Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.

Industry Canada (RSS-Gen Issue 4)

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information canadienne sur l’exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou

émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

CAN ICES-3(B)/NMB-3(B)

Sales

P: 801-822-5450

E: [email protected]

Technical Support

P: 801-822-5450 Option 3

E: [email protected]

© 2015 Luxul. All Rights Reserved. LUX-QIG-XWS-1310 04281509

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement