UG_TE100-S55Eplus
TE100-S55Eplus
5-Port 10/100Mbps
NWay Auto-MDI
Fast Ethernet
Mini Switch
User’s Guide
FCC Warning
This equipment has been tested and found to comply
with the regulations for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with this user’s guide, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case
the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may be required
to take adequate measures.
VCCI Mark Warning
P/N:6012-0721051
Rev.C1-01
A BOUT T HIS G UIDE
Congratulations on your purchase of the 5-Port
10/100M NWay Ethernet Mini Switch. This device
integrates 100Mbps Fast Ethernet and 10Mbps
Ethernet network capabilities in a highly flexible
desktop package.
Purpose
This manual discusses how to install your 5-Port
10/100M NWay Ethernet Mini Switch.
Terms/Usage
In this guide, the term “Switch” (first letter upper
case) refers to your 5-Port 10/100M NWay Ethernet
Mini Switch, and ”switch” (first letter lower case)
refers to other Ethernet switches.
E XTERNAL C OMPONENTS
This section identifies all the major external
components of the hub. Both the front and rear
panels are shown followed by a description of each
panel’s features. The indicator panel is described in
detail in the next chapter.
Front Panel
The figure below shows the front panels of the
switch.
Power:
This indicator lights green when the hub is receiving
power. This LED remains off for no power.
Link/Act:
This indicator lights green when the port is
connected to an active Ethernet/Fast Ethernet device.
The indicator blinks green when the port is
transmitting or receiving data on the network.
100M:
This indicator lights green when the port is
connected to an active 100Mbps Fast Ethernet
device. This LED is off when the connection is
10Mbps or there is no connection to the port.
FDX/COL:
This LED indicator lights green when a respective
port is connected in full duplex (FDX) mode. This
LED blinks green when collisions occur on the
respective port .
Rear Panel
DC Power Jack:
Power is supplied through an external AC power
adapter. Check the technical specification section
for information about the AC power input voltage.
Since the Switch does not include a power on/off
switch, plugging the power adapter into a power
outlet will immediately power on the Switch.
Auto-MDI Jacks (port 1~5):
These RJ45 jacks support automatic MDI-II/MDI-X
crossover detection function. This feature avoids the
confusion of using crossover cable and uplink port,
which make the Switch a true “plug and play”
device.
With the Auto-MDI function, you can connect each
Switch port to another Ethernet device’s “regular
port” or “uplink port” using regular “straightthrough” RJ45 cable or “crosso ver” RJ45 cable.
T ECHNICAL S PECIFICATIONS
General
Standards
IEEE 802.3 10BASE -T Ethernet
IEEE 802.3u 100BASE -TX Fast Ethernet
ANSI/IEEE 802.3 NWay Auto-negotiation
IEEE 802.3x Full duplex Flow Control
Protocol
CSMA/CD
Data Transfer
Rate
Ethernet: 10Mbps (half duplex)
20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half duplex)
200Mbps (full- duplex)
Topology
Star
Network
Cables
10BASET: 2-pair UTP Cat. 3,4,5, EIA/TIA- 568
100-ohm STP (max. 100 meters)
100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568
100-ohm STP (max. 100 meters)
Number of
Ports
5 x 10/100Mbps NWay Auto-MDI ports
Physical and Environmental
DC inputs
7.5VDC/1A
Power Consumption
7.5 watts. (max.)
Temperature
Operating: 0? ~ 50? C
Storage: -10? ~ 70? C
Humidity
Operating: 10% ~ 90%
Storage: 5% ~ 90%
Dimensions
116 x 70 x 25 mm (W x H x D)
EMI:
FCC Class B, CE Mark B, VCCI -B
Performance
Transmission
Method:
Store-and-forward
RAM Buffer:
128KBytes per device
Filtering Address
Table:
4K entries per device
Packet
Filtering/Forwarding
Rate:
10Mbps Ethernet: 14,880pps
MAC Address
Learning:
Automatic update
100Mbps Fast Ethernet: 148,800pps
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising