Användarmanual Eng

Användarmanual Eng
MCT-220
User Guide
Wireless Emergency Button
1. INTRODUCTION
1.1 General
The MCT-220 enables people, for example senior citizens in their
home environment, to transmit an emergency call when they are at
some distance from their communication unit.
1.2 Additional Features
• Can be used for panic alarm, when used with a Visonic Amber or
PowerMax family system.
• Can be used for X-10 devices activating when used with a Visonic
PowerMax family system.
• An auxiliary sensor can be connected to the MCT-220. When the
sensor is in an alarm state, the MCT-220 sends an alarm message
from its auxiliary channel.
• Enables people to answer incoming calls when the telephone is out
of reach, when used with a Visonic Amber family system.
• MCT-220 button pressing period - 2 seconds or 300 milliseconds
(selectable by an internal function selector).
Figure 1 – MCT-220
• Supervision signal is regularly transmitted to the communication
unit.
• In low battery voltage state, an alarm message is sent to the
communication unit and the MCT-220 button blinks during
transmission.
• Push button back light can be switched On/Off by an internal
function selector.
• Auxiliary input E.O.L / Normally Close type can be selected by an
internal function selector.
• Auxiliary input alarm restore message can be enabled / disabled
(selected by an internal function selector).
• Water resistant.
2. SPECIFICATIONS
GENERAL
Compatibility: Compatible with all Visonic control panels and
receivers.
Operating Frequencies (MHz): 315, 433.92, 868.95, 869.2125 or
869.
ELECTRICAL
Internal Battery: 3V battery type CR123
Current Consumption: 35 mA (during transmission), 20µA in
standby mode.
Battery Life Expectancy: 5 years (for one alarm per day)
ENVIRONMENTAL
Operating Temperature: 0° to 50°C (32° to 122°F)
Standards: Designed to comply with FCC CFR 47 Part 15, UL 1637,
Directive 1999/5/EC, EN 50131-2, Grade 2, Class II, RSS-210.
PHYSICAL
Dimensions (Diameter x H): 90 x 35 mm (3-1/2 x 1-3/8 in)
Weight: 110g (3.9 oz.)
Color: White
Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user's authority to operate the
equipment.
Compliance with standards (Europe): ETSI EN 301 489-3 V1.4.1,
EN 50130-4, & A1: & A2, EN 300 220-2 V2.1.2, EN 300 220-1 V2.1.1,
EN 50131-1, Grade II, Class II, EN 60950-1
This device complies with Part 15 of the FCC Rules and RSS-210 of
Industry and Science Canada. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device complies with the essential requirements and provisions
of Directive 1999/5/EC of the European Parliament and of the Council
of 9 March 1999 on radio and telecommunications terminal equipment.
3. PREPARATION FOR USE
Set the switches as desired (see table 1)
prior to applying power. Use a ball point pen
or another pointed object to shift the switch
levers. The ON position is indicated on
the switch body.
3.1 Cover Removal
COVER
ON
1
2
3
4
Figure 4
Function Selector
Table 1. Function Selector Description
BASE
Function
SW1
1
2
SW2
SW3
Figure 2 – Cover Removal
3.2 Function Selector Setting
The MCT-220 has a 4 lever switch (see Fig. 3). Each switch lever
allows you to select one of two options.
FUNCTION SELECTOR
BATTERY
MOUNTING HOLE
MOUNTING HOLE
WIRING KNOCKOUT
AUXILIARY INPUT TERMINALS
SW4
Back light ON/OFF
Aux. input type
selector (*)
Auxiliary input
restore reports
enable/disable (**)
Pressing period of
push button
Pos.
ON
OFF
ON
OFF
ON
Selected Option
Button's back light ON
Button's back light OFF
Aux. input is E.O.L. (47 kΩ)
Aux. input is N.C.
Aux input Restore events
are reported
OFF Aux. input restore events
are not reported
ON 2 seconds
OFF 300 milliseconds
Default
ON
OFF
ON
OFF
(*) SWITCH SW2 determines whether the auxiliary input will behave
as a 47kΩ end-of-line (E.O.L.) input or as a normally closed
(N.C.) input.
(**) SWITCH SW3 determines whether the MCT-220 will report a restore
event when the auxiliary input restores from an alarm condition.
3.3 Battery Insertion
Insert battery (see Figure 3) – Verify proper polarity.
Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the manufacturer's
instructions.
Figure 3 – Internal View
D-301850 MCT-220 User’s Guide
1
4. INSTALLATION
4.1 Wall Mounting
1
2
3
Mark
Drill
Fasten
4
Insert into rubber base
Figure 5 – Wall Mounting
4.2 Desktop Mounting
4.3 Auxiliary input Wiring
Connect the 2 auxiliary device wires to the proper AUXILIARY
terminals GND and IN1 - see figure 3.
4.4 Enrolling
The MCT-220 and its auxiliary input should be enrolled into the
communication unit memory, in order that the communication unit will
be able to identify their signals.
If the MCT-220 is used with PowerMax family, refer to the relevant
installer / programming guide, ENROLLING WIRELESS DEVICES
section. If the MCT-220 is used with AMBER, refer to the HHCPC
software user guide.
When you are instructed to initiate transmission:
A. For the MCT-220 enrolling, press the MCT-220 button.
B. For the Auxiliary input enrolling, simulate an alarm event via the
auxiliary detector.
4.5 Test
Figure 6 – Desktop Mounting
Perform the following actions and verify that the communication unit
properly responds:
A. Press the MCT-220 button.
B. Simulate an event from the auxiliary input.
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser
only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a
period of twelve (12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and
operated under conditions of normal use in accordance with the Manufacturers recommended installation
and operation instructions. Products which have become defective for any other reason, according to the
Manufacturers discretion, such as improper installation, failure to follow recommended installation and
operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or
tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or
that the Product will prevent any death and/or personal injury and/or damage to property resulting from
burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or
protection. The Product, properly installed and maintained, only reduces the risk of such events without
warning and it is not a guarantee or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER
WARRANTIES WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE,
INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY
ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR
DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY
INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT,
INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT
FAILED TO FUNCTION.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising
under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN
ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated
damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and
warranty and he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning
of any telecommunication or electronic equipment or any programs.
The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the
Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or
replacement shall not extend the original Warranty period. The Manufacturer shall not be responsible for
dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the
Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the
Purchaser and are not included in this Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any
person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall
apply to the Product only. All products, accessories or attachments of others used in conjunction with the
Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall
not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially
or otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of
others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original
Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is
contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning: The user must follow the Manufacturer’s installation and operational instructions including testing
the Product and its whole system at least once a week and to take all necessary precautions for his/her
safety and the protection of his/her property.
1/08
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
EMAIL:
info@visonic.com
INTERNET:
www.visonic.com
VISONIC LTD. 2013 MCT-220 user guide D-301850 (Rev 3, 6/13)
2
D-301850 MCT-220 User’s Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising