TA70-B8237 Quick Installation Guide
Document # D2234-100/ Revision 1.0
1
General Information
Read Me First
1. The Barebone User’s Manual is available for download from our Web site at http://www.tyan.com. Make sure to read all precautions and instructions before you start installing the server system.
2. Refer all servicing to qualified personnel to avoid the risk of damage to the server system.
3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
4. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise caution when installing the processors as the manufacturer’s warranty does not cover damage inflicted upon the motherboard, including damage to the CPU sockets.
Box Content
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
2U barebone, (24) hot swap HDD bays M1702T70-USB
3
System Installation
Open the Chassis
Preparing the Chassis
Read normal ESD (Electrostatic Discharge) procedures.
Place your TYAN ® Server Chassis on a flat anti-static surface to perform the following integration procedures. Read
ESD procedures before reaching inside to install components.
M1701T70-FPB TYAN ® S8237 system board
(pre-installed)
(5) System fans
30
30
(2) M2212-R16-2F Riser card
Accessories
CPU heatsink x 2
M1807TA7-FB (3) M1256T70-BP6-8 HDD BP
Quick Installation
Guide
FL00EUI-A
Sliding Rails x 2 & Screw Pack x 1 Quick Installation Guide x 1 Driver's and Utilities CD x 1
FL00EUI-A
AIr Duct x 1 AC Power cord (US) x 2 AC Power Cord (EU) x 2 Screw Pack x 2
Required Hardware Components
Minimum Hardware Requirements
To avoid integration difficulties and possible board damage, your system must meet the following minimum requirements:
• Processor: AMD® Opteron® 6100 Series Processors (Magny-Cours), AMD® Opteron® 6200 Series Processors (Interlagos), AMD®
Opteron® 6300 Series Processors (Abu Dhabi)
• Memory Type: Minimum of one 1GB, 240-pin DDR3 800/1066/1333/1600/1866-MT/s DIMMs.
• Hard Disk Drives: SATA/SAS
• Rack Mount Kit (Industry 19" rack-mountable)
NOTE: For an up to date list of compatible hardware, please visit the system’s support page on www.tyan.com
Tools Required
1 Loosen the 2 thumb screws on the back side.
Install the Processor
2 Take off the top cover.
1 Open the socket lever.
2 Open the CPU socket cover.
3 Take off the air duct.
3 Remove the CPU protective cap.
Phillips Screwdriver Flat-head Screwdriver
2
Motherboard Placement
Motherboard Placement
Anti-Static Wrist Strap e d 35 34 3332
31 30 29 28 27
A
1 a
C
D SR5670 CPU 0
4
5
6
E
F
7 8
SP5100
9 1011
12
CPU 1
B
13 14 15 16 17
Install the CPU Heatsink
1
Apply the thermal grease.
Install the Memory
2
Install the CPU heatsink.
3
Secure the heatsink screws.
1
Unlock the clips.
Install the Hard Disks
2
Insert the memory module.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 18
19
20 21
22 23
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 18
19
20 21
22 23
1 Press the locking lever and pull the locking lever open.
2 Slide the HDD tray out.
3
Lock the clips.
3 Unscrew the HDD tray bracket.
0
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17 18
19
20 21
22
23
0
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17 18
19
20 21
22
23
26
25
21
20
19
18
4 Install the processor and make sure the gold arrow is located in the right direction.
5 Close the CPU socket cover.
6 Close the socket lever.
CONNECTORS
5.
6.
7.
8.
1.
2.
3.
4.
TYAN Module Header (J96)
ID LED (LED1)
USB2.0 Port (USB5)
NCSI Header (J4)
USB2.0 Port (USB4)
LAN Port # 3 (LAN3)
VGA Header (J27)
IMC IPMB Header (J6)
9.
10.
11.
12.
System BIOS (U108)
SATA SGPIO Header (J63)
SATA Connector (SATA0~SATA5)
USB Front Panel Header (J91)
13/14. 4-pin Power Connector (PW2/PW1)
15. 16-pin Power Connector (PW3)
29.
30.
31.
32.
33.
34.
35.
16/17. 8-pin Power Connector (PWR3/PWR2)
18. 4-pin Power Connector (PW4)
19/20. Fan Connector (J23/J24)
21/22. Fan Connector (J21/J15)
23/24. Fan Connector (J14/J10)
25/26. Fan Connector (J9/J55)
27/28. 8-pin Power Connector (PWR5/PWR4)
Front Fan Header (J99)
Chassis Intrusion Header (JP16)
Front Panel Header (J64)
Super I/O ROM (U118)
USB Front Panel Header (J90)
Vertical Type-A USB Connector (USB0)
COM Header (J8)
SLOTS
E
F
A
B
C
D
CPU0 DIMM SLOT [Channel A/B/C/D]
CPU1 DIMM SLOT [Channel A/B/C/D]
PCI-E X 8 MEZZ Card
PCIE Gen2 slot (x8)
PCI-E X 1 IMC Card
PCIE Gen2 slot (x8)
JUMPERS a b
COM Debug Jumper (JP14)
Clear CMOS Jumper (JP8) c Chassis Config Jumper (JP9/JP10) d/e COM Debug Jumper (JP11/JP12)
Note:
- There is risk for the customers when setting the jumper by yourselves.
- Customers need to add an external PCI-E VGA card.
4 Place a hard drive into the drive tray.
Use four screws to secure the HDD.
5 Reinsert the HDD tray into the chassis.
6 Press the locking lever to secure the tray.
Repeat the same procedures to install other HDD trays.
4
I/O Ports
Locate the External I/O Port
Ethernet
(LAN3) shared with IPMI
USB2.0 Port USB2.0 Port
5
Caution
CPU Cover for DOA/RMA
Note: Please save and replace the CPU protection cap when returning the server board for service.
Installing the Air Duct
1
Place the Air Duct onto the chassis.
Installing the Add-On card (Optional)
1 Unscrew the riser card assembly.
3 Unscrew to remove the PCI bracket from the riser bracket.
5 Secure the add-on card onto the riser bracket.
7 Secure the add-on module to the chassis using a thumb screw.
2 Lift the riser bracket up.
4 Insert the add-on card onto the riser bracket.
6 Insert the riser bracket with the add-on module onto the chassis.
NOTE:
1. Connect the add-on power cable to the connector of the add-on module.
2. There are two riser brackets inside the chassis. To install other add-on cards onto the riser brackets, please refer to the barebone user’s manual on our web site at http://www.tyan.com for more details.
