Miele F1471VI Operating and Installation Instructions

Operating and Installation

Instructions

Freezer with Ice/Water Dispenser

F 1471 Vi

To prevent accidents and appliance damage read these instructions before installation or use.

en - US, CA

M.-Nr. 09 743 700

Contents

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Control panel for freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Control panel for Ice/Water Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using the settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Turning the button sound On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Turning off for longer periods of time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Temperature and door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the freezer efficiently . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Freezing food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cooling drinks quickly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

SuperCool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Ice/Water Dispenser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Anti-condensation heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Anti-clumping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Button sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Automatic defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjusting the interior fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Cleaning the interior and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Aluminum frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Ice cube container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Drip tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Ventilation slits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2

Contents

Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Water filter change indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Exchanging the water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Confirming the filter change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using an external water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Lead free certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Stainless steel panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Custom door panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Door dimensions (open 115°) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Niche dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

RemoteVision module installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Preparing the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Sliding the appliance into the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Aligning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Attaching the appliance to the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Preparing the custom door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Attaching and aligning the custom door front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Aligning the Ice/Water Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Attaching the frame and the shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

RemoteVision (optional accessory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

3

IMPORTANT SAFETY INSTRUCTIONS

When using the appliance, follow basic safety precautions, including the following:

Read all instructions before installation and use to prevent accidents and machine damage.

This appliance is intended for residential use only. Use only as described in this Operating manual.

This appliance is for household use only. Use this appliance only for its intended use as described in this manual. Any other use could be dangerous.

This appliance complies with current safety requirements. Improper use of the appliance can cause personal injury and material damage.

Keep these operating instructions in a safe place and pass them on to any future user.

Electrical safety

~

Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt.

~

Before installation or service, disconnect the power supply to the work area by unplugging the unit,

"tripping" the circuit breaker or removing the fuse.

~

Do not use an extension cord to connect this appliance to electricity.

Extension cords do not guarantee the required safety of the appliance

(e.g., danger of overheating).

~

Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electrician.

~

Only connect power to the appliance when all installation and plumbing work is complete.

4

IMPORTANT SAFETY INSTRUCTIONS

Installation

This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.

Keep the door closed until the appliance is completely installed and secured per installation instructions.

~

Before installing the appliance, check for externally visible damage.

Do not operate a damaged appliance.

~

This appliance must be installed and connected in compliance with the installation instructions.

~

The appliance must be properly installed before operation to ensure that no electrical components are accessible.

~

Installation work and repairs should only be performed by a trained technician in accordance with national and local safety regulations. Repairs and other work by unqualified persons could be dangerous.

~

Installation must comply with local plumbing regulations and state laws.

~

Connection to the water supply and any repairs to the ice maker must only be carried out by a suitably qualified person.

~

Before making plumbing connections, ensure the appliance is disconnected from the mains electricity supply.

~

Do not operate any appliance with a damaged cord or plug, or if the appliance has been damaged in any manner. Contact Miele’s Technical Service Department.

~

This appliance must not be used in a non-stationary location (e.g. on a ship).

~

Do not install the freezer in a room with too low an ambient temperature, e.g., a garage, as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature.

~

In appliances with an automatic ice maker, avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the ice maker. Do not place fingers or hands on the automatic ice making mechanism while the freezer is plugged in.

~

The ice cube maker is not suitable for connection to a hot water supply.

~

Do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after the filter is used; the filter alone is not an adequate safeguard.

5

IMPORTANT SAFETY INSTRUCTIONS

Use

~

This appliance is not designed for commercial use. It is intended for use in domestic households and in similar working and residential environments such as:

– shops, offices and similar work environments

– by customers in hotels, motels, Bed

& Breakfasts or similar residential environments.

~

This appliance is not intended for outdoor use.

~

The appliance is only intended for residential use to store frozen foods, freeze fresh foods and prepare ice.

All other uses are prohibited and may be dangerous.

~

Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person.

~

To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area.

~

After your freezer is in operation, do not touch the cold surfaces in the freezer compartment, particularly when hands are damp or wet. Skin may adhere to these extremely cold surfaces.

~

Avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the ice maker. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.

~

Do not refreeze frozen foods which have thawed completely.

~

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

~

To avoid serious illness or death, do not deactivate the water filter display.

~

Do not use sharp-edged objects to remove frost and ice, or separate frozen foods and remove ice trays.

They will damage the evaporator, causing irreversible damage to the appliance.

~

Do not use defrosting sprays or de-icers, as they might contain substances which could damage the plastic parts or which could cause a build-up of gases and pose a danger to health.

~

Do not use any oils or grease on the door seal, as these will cause the seal to deteriorate and become porous with time.

6

IMPORTANT SAFETY INSTRUCTIONS

~

Do not block the ventilation gaps in the plinth or the top of the appliance housing unit, as this can impair the efficiency of the appliance, increase the electricity consumption and cause damage to the appliance.

~

Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit.

~

Before using the Ice/Water dispenser it is important to flush the lines and clean the part thoroughly.

Disposal of your old appliance

~

Before disposing of an old appliance, first make the door latch or lock unusable.

~

Take off the door.

~

Leave the shelves in place so that children may not easily climb inside.

~

Consult with your municipal policy on recycling.

~

Be careful not to damage any part of the pipework while awaiting disposal by:

-

-

puncturing the refrigerant channels in the evaporator.

bending any pipework.

scratching the surface coating.

Splashes of refrigerant can damage the eyes.

~

Your old freezer may have a cooling system that used CFCs

(chlorofluorocarbons). CFCs are believed to harm stratospheric ozone.

If you intentionally release this CFC refrigerant, you can be subject to fines and imprisonment under provisions of environmental legislation. Make sure the

CFC refrigerant is removed and disposed of by a qualified technician.

SAVE THESE

INSTRUCTIONS

7

Guide to the freezer a Interior lighting b Door shelf c Ice cube maker d Ice cube container e Interior shelf f Control panel for the Freezer g Main switch to turn the appliance

On/Off h Freezer baskets i Water filter j Ice / Water dispenser in the door k Control panel for Ice / Water

Dispenser l Ice / Water dispenser outlet m Drip tray with grid and cover

8

Guide to the freezer

Control panel for freezer

a Access button "p" activates the control panel b Temperature display

X colder; Y warmer

Allows you to set the desired temperature in the freezer c On/Off sensor button for the

SuperCool function d On/Off sensor button for the

Ice/Water dispenser e Sensor button for the temperature and/or door alarm* f Water filter change indicator*

* Only visible when the relevant function is activated

Control panel for Ice/Water

Dispenser

a Lighting sensor button b Water sensor button c Ice cube sensor button d Crushed ice sensor button e Safety lock sensor button

9

Before use

Before using for the first time

^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap.

Dry with a soft cloth.

Turning the appliance On/Off

^ Open the appliance door.

If the appliance was transported or laid horizontally for any reason, allow it to stand vertical for at least 8 hours before turning it on. Failure to do so will affect the functioning of the appliance.

^ Turn the appliance On/Off with the main switch.

The main switch is located on the right-side underneath the control panel.

Once on, the appliance begins cooling.

When the door is open, the interior lights come on.

The access button will light in the control panel.

The preset temperatures (factory default settings) are reached after a few hours. Do not put any food in the appliance until the preset temperatures are reached.

,

Turning off the appliance with the main switch does not safely isolate it from the power supply.

10

Settings

Using the settings

This appliance is operated with the use of touch keys activated by a finger.

– An available button will appear white.

– A selected button will appear yellow.

Additional settings

In the settings mode you can select and change functions.

In settings mode, certain settings can be changed. The function possibilities are described in the respective chapters of this manual.

Overview of the selectable function settings:

^ Touch the access button "p" so it turns yellow.

On the control panel you will see additional sensor buttons to operate the appliance.

These buttons allow you to:

– adjust the temperature,

– select the SuperCool function, or

– turn the Ice/Water Dispenser On/Off.

For additional information, see the corresponding sections in this manual.

^ To leave the settings menu, touch the access button " p" so it turns white.

The last settings entered are stored.

If the access button is not pressed the display will go out after approx.

30 secs.

The other sensor buttons now disappear from the control panel.

Function

To enter and exit the

Settings mode

Temperature unit

°C - °F

(see "Setting the temperature")

RemoteVision Module settings (optional accessory)

Button sound on/off

(see "Settings") no function

Display text

c

†

;

=

^

11

Settings

Turning the button sound

On/Off

If you prefer the buttons to be silent when touched the button sound can be turned off.

^ Touch the access button "p" so it turns yellow.

^ Note the position of the X button, but do not touch.

^ Touch the access button "p" again so it turns white.

Only the access button " p" is visible.

^ Place one finger on the position of the X button and hold (the X button will not be visible).

^ While holding down the X button, press the access button " p" once.

Keep holding the X button down until the following appears in the display

(approx. 5 seconds).

^ Tap the X button until = appears in the display.

^ Touch the access button "p" to confirm.

^ By touching the X button, you can choose between:

= 0 : Button sound is off

= 1 : Button sound is on

= – : Return to menu.

^ Touch the access button "p" to confirm the setting.

^ Tap the X button until you see ; in the display.

^ Touch the access button "p".

You have now left the Custom settings mode.

Note: the button sound of the

Ice/Water dispenser must be turned off separately.

When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.

12

Turning off for longer periods of time

If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken:

^ Shut off the water supply line,

(several hours before switching off the appliance)

^ Take all food out of the appliance

^ Turn the appliance off

^ Unplug the appliance

^ Empty the ice cube container

^ Clean the interior

^ Remove and discard the water filter

(secure the filter cap)

^ Leave the door open to prevent odors

Settings

13

Temperature and door alarm

The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door.

The alarm system is always operational, it does not need to be switched on.

Turning the temperature alarm Off

As soon as the alarm condition is corrected, the alarm signal turns off and the affected zone stops flashing in the display. The "alarm" indicator goes out.

Temperature alarm

If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes and the temperature flashes in the control panel.

The temperature display shows the highest temperature reached during the alarm.

The alarm will sound and the display will flash if:

– too much warm air flows into the appliance, for example when food is being loaded, re-arranged, or taken out.

– large amounts of food are being frozen at once.

– the power fails.

As soon as the alarm condition is corrected the alarm with turn off and the sensor button for alarm will go out.

^ To turn the alarm off early, press the "alarm" sensor button.

The alarm signal turns off. The "alarm" indicator remains on until the alarm condition is corrected.

If the temperature in the freezer zone reaches 0°F (-18°C) or higher, check that food has not defrosted.

Door alarm

If the appliance door is left open, an alarm signal will sound and the "alarm" indicator will turn red after five minutes.

Once the door is closed the alarm will turn off and the "alarm" indicator will go out.

Turning the door alarm Off

To turn the alarm off early:

^ The "alarm" indicator and signal will turn off.

The alarm will turn off and the "alarm" indicator will go out.

14

Setting the temperature

Setting the temperature

^ Touch the access button "p" so it turns yellow.

^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder.

Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.

The temperature display on the control panel always shows the

desired temperature.

Temperature range

The temperature can be set within the following range:

7°F to -11°F (-14°C to -24°C).

To freeze fresh food and store frozen food for an extended period of time, a temperature of 0°F (-18°C) is suggested.

The room temperature and the installation location can affect the time it takes for the appliance to drop to the coldest temperature. If the room temperature is too high, it may not be possible for the appliance to reach the lowest temperature.

15

Setting the temperature

Temperature unit

(Fahrenheit/Celsius)

The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C).

^ While holding down the X button, press the access button " p" once.

Keep holding the X button down until the following appears in the display

(approx. 5 seconds).

^ Touch the access button "p" so it turns yellow.

^ Note the position of the X button, but do not touch.

^ Touch the access button "p" again so it turns white.

Only the access button " p" is visible.

^ Place one finger on the position of the X button and hold (the X button will not be visible).

^ Tap the X button until † appears in the display.

^ Touch the access button "p" to confirm.

^ By touching the X button you can select either Fahrenheit or Celsius for the temperature display.

† 0: Fahrenheit

† 1: Celsius

† –: return to menu.

^ Touch the access button "p" to confirm the setting.

^ Tap the X button until a ; appears in the display.

^ Touch the access button "p".

You have left the Custom settings mode.

When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.

16

Using the freezer efficiently

Freezing food

Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food.

Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.

Before placing food in the freezer

^ When you are planning to freeze large amounts of food (more than

4 ½ lbs [2 kg]), switch on the

SuperCool function ahead of time

(see "SuperCool").

This will provide the food already in the freezer with a protective boost of cold air.

Placing food in the freezer

Food to be frozen can be placed anywhere in the freezer.

The freezer baskets can hold a maximum of 35 lbs (16 kg) of frozen food.

^ Spread the food to be frozen across the bottom of the freezer basket or across the shelves, so that it will freeze through to the core as quickly as possible.

^ When placing items in the freezer, make sure the packaging and containers are dry, to keep them from sticking together when frozen.

When freezing, try not to let frozen food come into contact with unfrozen food, this could cause the frozen food to defrost.

17

Using the freezer efficiently

Defrosting

Frozen food can be defrosted in different ways:

– in a microwave oven,

– at room temperature,

– in the refrigerator (the cold given off by the frozen food helps to keep the other food cold),

– in a steam oven.

Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry. Drain it away and promptly wash the container, the sink and your hands. Danger of salmonella poisoning.

Fruit should be defrosted at room temperature in its packaging, or in a covered bowl.

Most vegetables can be cooked while still frozen. Simply place directly into boiling water or hot oil.

Cooling drinks quickly

To cool drinks quickly, switch on the

SuperCool function. See "SuperCool" for more information.

Do not leave bottles in the freezer for more than 1 hour, closed containers could burst.

18

Using the freezer efficiently

Freezing tips

– The following are examples of foods

suitable for freezing:

Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals.

– The following examples of foods not

suitable for freezing:

Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears.

– To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.

To blanch: bring a large saucepan of water to a boil, then submerge the vegetables in rapidly boiling water for 2-3 minutes, depending on type.

Remove, and plunge into ice-cold water to cool quickly. Drain and pack for freezing.

– Lean meat freezes better than fatty meat, and can be stored for considerably longer.

– To prevent chops, steaks, cutlets or rolled meats from freezing together in solid blocks when packed, separate with a sheet of plastic freezer wrap.

– Do not season fresh foods or blanched vegetables before freezing. Cooked food can be lightly seasoned before freezing, but care should be taken as the taste of some spices alters when frozen.

– Do not place hot foods or drinks in the freezer. This causes already frozen food to thaw, and increases the energy consumption considerably. Allow hot foods and drinks to cool down before placing them in the freezer.

Packing tips

^ Unsuitable packing material

- wrapping paper

- greaseproof paper

- cellophane

- garbage bags

- plastic shopping bags

Suitable packing material

- plastic freezer bags/wrap

- aluminum foil

- freezer containers

^ To help prevent freezer burn, expel as much air as possible from bags, etc., before sealing them.

^ Close the packaging tightly with

- plastic clips

- twist ties

- rubber bands

^ Mark the package to indicate the contents and the date of freezing.

19

SuperCool

When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature).

SuperCool

The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer.

If the max. freezing capacity is used,

24 hours are recommended.

This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.

Switching on SuperCool

Switching off SuperCool

The SuperCool function automatically switches off after approx. 52 hours. The sensor button turns white, and the appliance continues running at normal power.

To save energy, you can switch off the

SuperCool function once the food is sufficiently chilled.

^ Touch the SuperCool sensor so that it turns white.

The temperature display returns to the original temperature setting.

The appliance now continues running at normal power.

^ Touch the SuperCool sensor so that it turns yellow.

The temperature now begins to fall, with maximum cooling performance.

The new temperature setting appears in the display -22°F (-30°C).

20

Ice/Water Dispenser

Using the Ice/Water Dispenser for the first time

Before using the Ice/Water

Dispenser for the first time, you must flush then fill appliance water lines with water.

Flushing the lines of the Ice/Water

Dispenser

^ Open the freezer door.

^ Touch the "Access" button so it turns yellow.

^ Touch the "ice" sensor button so it turns yellow.

^ Close the appliance door.

After opening and closing the door, it may take a few seconds before the Ice/Water Dispenser is ready for use.

The "water" button on the control panel of the Ice/Water Dispenser flashes white.

^ Place a large container under the dispenser.

^ Touch the "water" button until it flashes yellow.

^ Touch and hold the "water" button again.

This activates the flushing function, which uses approximately 1.6 gallons

(6 liters) of water.

You can interrupt the flushing process at any time to empty the container, by taking your finger off the "water" button.

During this time, the "water" button will flash yellow again.

As soon as the flushing process is complete, you will hear a beep, and the buttons on the control panel will turn white.

You can now use the Ice/Water

Dispenser.

For the automatic ice/water dispenser to operate, it must be connected to the household power and water supply.

Use sturdy glass when dispensing water or ice - risk of injury from broken glass!

Keep fingers clear of the dispenser opening. Risk of injury!

21

Ice/Water Dispenser

Turning on the Ice/Water

Dispenser

Before using the Ice/Water

Dispenser for the first time, you must flush the water lines.

^ Open the freezer door.

^ Be sure the ice cube container is under the ice maker.

Ice cubes can only be produced if the ice cube container is completely closed.

^ Touch the "ice" button so it turns yellow.

^ Close the freezer door.

The ice/water dispenser is now ready for use.

After opening and closing the door, it may take a few seconds before the Ice/Water Dispenser is ready for use and the touch controls can be used again.

^ Turn on the Ice/Water dispenser with a finger touch to the control panel or by passing your hand under the dispenser to activate it via the light sensor.

All of the touch controls for the

Ice/Water Dispenser should now appear white.

If this is not the case, the Safety Lock is activated i.e. "lock" will appear yellow.

See "Safety Lock".

If "lock" is blinking, the drip tray needs to be emptied (see "Cleaning and care").

Once the freezer has cooled to a freezing temperature, the ice cube maker fills with water.

Do not place any bottles or food for rapid cooling in the ice cube maker.

The ice cube maker could become blocked or damaged.

Discard all ice cubes, crushed ice and water produced during the first

24 hours after switching on the ice/water dispenser. The water is used for the initial flushing of the water supply.

This applies to the first use, as well as when the appliance has been out of service for a long time.

22

Ice/Water Dispenser

Dispensing water

^ Place a suitable cup on the drip tray under the ice/water dispenser.

Release the button when the jar is almost full. Ice in the discharge may cause the cup to overflow or block the discharge.

^ Press and hold the "water" button.

As long as you hold in the "water" button, water will flow from the dispenser.

After a period of time the water flow will automatically stop. If more water is needed press the "water" button again.

The ice cube maker can produce approx. 150 ice cubes within 24 hours.

Note: Ice production will vary due to your water supply temperature, pressure and hardness.

The amount of ice cubes produced depends on the temperature in the freezer section. The lower the temperature, the more ice cubes will be produced in a given period of time.

If you would like the water colder, place ice cubes in the glass before dispensing water.

Dispensing (crushed) ice

As soon as the drip tray indicator signals that the drip tray is full, the current operation will automatically stop.

Empty out the drip tray using a sponge or dish towel.

After the initial start-up it may take up to 24 hours for the first ice to be produced.

^ Place a suitable cup on the drip tray under the dispenser.

The ice dispenser produces a max. of

150 ice cubes per 24 hours.

The production volume of ice depends on the temperature in the freezer. The lower the temperature the more ice that will be produced in a certain period of time.

^ Press and hold the "cubes" or

"crushed" button.

As long as you hold in the desired button, ice will fall from the dispenser.

After a while dispensing will stop automatically. Press the sensor again if you need more ice.

If the "lock" flashes the drip tray needs to be emptied and the dispensing is automatically stopped.

Empty the drip tray using a sponge or towel.

23

Ice/Water Dispenser

If the ice/water dispenser is not used for more than 2 minutes or the freezer door is opened, Standby mode is activated and the lighting for the ice/water dispenser will go out.

When used again, it will take a few seconds for the water and ice to be dispensed.

Safety lock

The Ice/Water dispenser can be locked to prevent unwanted use.

If the Ice/Water dispenser is not used for longer than 2 minutes, it switches into standby mode, and the Ice/Water dispenser lighting turns off.

Turning off the Ice/Water dispenser

The water supply line must be shut off several hours before the appliance or ice maker is switched off.

^ Open the freezer door.

^ Touch the "lock" button so it turns yellow.

The Ice/Water dispenser buttons are now locked.

To unlock the buttons:

^ Touch the "lock" button so it turns white.

Lighting

In order to turn the Ice/Water dispenser lighting on or off:

^ Touch the sensor button for the ice maker so that it turns white.

^ Touch the "light" button so it turns yellow (lighting on) or white (lighting off).

24

Ice/Water Dispenser

Settings

The following settings on the Ice/Water dispenser can be adjusted:

Entering the settings mode

Anti-condensation heater

A heater behind the control panel of the

Ice/Water dispenser ensures that frost and ice do not build-up. To save energy, you can turn the heater off.

This feature is turned off by factory default.

To turn the anti-condensation heater on:

^ Touch and hold the "lock" button so that it appears white.

^ At the same time tap the "light" button

(do not hold down).

^ Hold the "lock" button for approx. 4 seconds until the "lock" and "light" buttons turn yellow.

The lighting color of other buttons indicates their On/Off setting.

Yellow (On)

White (Off)

^ Release both buttons.

^ Touch the "water" button until it turns yellow.

25

Ice/Water Dispenser

Anti-clumping

The anti-clumping feature ensures that crushed ice or ice cubes do not freeze together. A noise will be heard periodically to indicate that the feature is working. If the sound disturbs you, the feature can be turned off.

Note: Disabling the anti-clumping feature can result in the formation of ice clumps in the dispenser.

Button sound

If you prefer the buttons to be silent when touched, the button sound can be turned off.

This feature is turned on by factory default.

To turn button sound off:

This feature is turned on by factory default.

To turn the anti-clumping feature off:

^ Touch the "crushed" button until it turns white.

Exiting the settings mode

^ Touch the "cubes" button until it turns white.

^ Touch the "light" button or do not touch any buttons for one minute.

26

The freezer defrosts automatically.

The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically.

This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.

Automatic defrost

27

Adjusting the interior fittings

Moving the shelves

The shelves can be adjusted according to the height of the food.

^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings.

^ Pull the shelf forward.

^ Move the shelf to the desired height, then insert the (rear) hooks into place.

^ Make sure the shelf is level.

Door shelf

For easier loading, unloading and cleaning the door shelf can be shifted or completely removed.

^ Using both hands, grasp the door shelf by the frame, lift it upward a bit, then tip it slightly forward.

^ Slide the tipped shelf up or down along the side-rails, and click it back into place at the desired location.

^ Make sure that the basket is level.

Removing the door shelf:

^ Slide the shelf upwards all the way to the top of the side-rails until it can be removed.

Replacing the door shelf:

^ Insert the freezer basket at the top of the side-rails and slide it down into the desired position.

28

Adjusting the interior fittings

Freezer baskets

For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed.

^ Pull the basket forward until resistance is felt.

On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed.

Replacing the freezer basket

^ Fully extend the telescopic tracks.

^ Lay the basket onto the tracks so that it connects in the front and back.

^ Turn the safety lock back to the vertical position.

^ Slide the freezer basket in.

^ Using a suitable object, turn the safety lock to a horizontal position a.

^ On both sides of the basket, pull the latches b upward and lift the basket out of the freezer.

29

Cleaning and care

To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.

Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.

Non-abrasive cleaning agents are also unsuitable, as they can cause matte areas to appear.

Only use a mild solution of warm water and liquid dish soap to clean this appliance.

Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit.

Do not allow water to get into the electronic unit or lights.

The data plate located inside the appliance must not be removed. It contains information which is required in the event of a service call.

To better maintain your appliance avoid the following:

– cleaners containing soda, ammonia, thinners, or chlorides

– cleaners containing descaling agents or lime removers,

– abrasive cleaners,

– stainless steel cleaners,

– dishwasher soap (powder),

– caustic (oven) cleaners,

– scouring pads, steel wool, hard brushes,

– metal scrapers,

– eraser sponges,

– steam cleaning products.

Glass cleaners may be used to clean the exterior. However do not allow them to sit or "puddle", this can cause damage to the surface.

Remove the cleaner promptly.

30

Cleaning and care

Before cleaning

^ Use the main switch to turn the appliance off completely.

The main switch is located on the right side underneath the control panel.

^ Unplug the power cord.

^ Remove any food from the appliance and store it in a cool place.

^ Take out any removable parts, e.g., shelves, baskets.

Cleaning the interior and accessories

Use a mild solution of warm water and liquid dish soap. Wash all accessories and drawers by hand. Do not wash in a dishwasher.

^ Clean the appliance as needed.

^ After washing, wipe down the interior and accessories with a clean wet cloth, then dry with a soft cloth.

Leave the appliance door open for a short time, so the moisture can evaporate.

31

Cleaning and care

Aluminum frames

The frames of the door bins and shelves are made of aluminum.

^ Clean with a mild solution of warm water and liquid dish soap.

Aluminum is susceptible to scratches and nicks, treat with care.

The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.

Do not use stainless steel cleaners; lime removers; scouring pads, such as pot scrubbers; or used sponges that still contain abrasive cleanser residue to clean the frames.

Ice cube container

^ Pull out the ice cube container.

^ Empty and clean the ice cube container with lukewarm water.

^ Thoroughly dry the container and the anti-clumping screw to prevent new ice cubes from sticking.

^ To re-insert push the ice cube container all the way back onto the supports until it locks into position.

^ If the container cannot be pushed all the way back, twist the anti-clumping screw in the container.

Drip tray

The drip tray collects excess water.

As soon as the drip tray is full, the "lock" button on the Ice/Water dispenser control panel will flash. A sensor located in the drip tray detects when the drip tray is full.

The drip tray must be emptied and cleaned. However, to prevent odors, the drip tray should be cleaned daily.

When the "lock" button flashes yellow:

^ Remove the drip tray cover.

^ Empty and clean the drip tray using a sponge or kitchen towel.

^ Replace the tray cover.

The "lock" button is now white again.

32

Cleaning and care

Ventilation slits

^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed.

Door seals

Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time.

^ Clean the door seals with warm water and dry thoroughly.

After cleaning

^ Return all shelves and accessories.

^ Plug in the appliance and turn it on with the main switch.

^ Switch on the SuperCool function.

The freezer section will cool down quickly.

^ Once the temperature is cold enough, place the freezer baskets containing the frozen food into the freezer.

^ Turn off the SuperCool function on a temperature of 0 °F (-18 °C) is reached.

33

Cleaning and care

Changing the light bulb

The lighting automatically switches off after the door has been open for approx. 10 minutes. This is not a fault.

If the light does not come on when the door is opened briefly, the light bulb should be changed.

^ Use the main switch to turn the appliance off.

To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker.

Upper lighting

Never touch a halogen bulb with bare fingers.

When inserting a glass halogen bulb always hold with a soft cloth.

^ Remove the defective light bulb.

^ Place the new bulb in the socket.

Halogen bulb type:

20 W/12 V/socket GY 6.35.

^ Slip the rear of the light cover back into position, then pull it forward and into place.

^ Grasp the front of the light cover with both hands, and slide it back.

^ Carefully pull the cover forward and out.

34

Cleaning and care

Side lighting Ice/Water Dispenser lighting

Do not remove the light cover for the dispenser lighting. Should the lighting covers be damaged or need to be removed due to damage, do not look directly or with an optical instrument at the lighting.

^ Turn the light cover counterclockwise and pull out.

Never touch a halogen bulb with bare fingers.

When inserting a glass halogen bulb always hold with a soft cloth.

The lighting automatically switches off if the dispenser is not used for an extended period of time. This is not a fault.

If the light does not come on when the dispenser is used again, the light bulb should be changed.

The dispenser lighting should only be repaired or replaced by Miele

Technical Service.

^ Pull the defective light bulb from the socket.

^ Place the new bulb in the socket.

Halogen bulb type:

5 W/12 V/socket G 4.

^ Put the light cover back on and turn clockwise into place.

^ Restore power to the appliance.

35

Water filter

The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water.

Additional water filters are available from Miele.

It is important to change the water filter regularly.

To avoid serious illness or death, do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter.

Note:

– After installing a new water filter and switching on the ice maker, discard the first 24 hours' worth of ice production.

– If the ice maker has not been used for a prolonged time discard any ice cubes in the freezer, empty the container and discard the ice production of the next 24 hours.

– If the appliance or ice maker have not been routinely used for several weeks or months, or if the ice cubes have an unpleasant odor, change the water filter.

Water filter change indicator

The change indicator will appear approx. every 6 months depending on the quantity of ice produced.

– When the filter indicator lights red, this is an indication that a filter change will soon be necessary.

New water filters (Bypass and Active charcoal filters) are available from

Miele.

^ When the filter indicator flashes red in the display the filter must be changed.

36

Water filter

Exchanging the water filter

Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing.

^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1.

^ Pull the used filter cartridge out of the appliance, 2.

^ Remove the cap from the used filter,

3.

^ Take a new filter cartridge out of the packaging and remove the protective cap.

^ Push the cap onto the new filter cartridge, 4.

^ Push the filter cartridge with cap, in a horizontal position, all the way into the opening in the base panel, 5.

^ Rotate the filter cartridge clockwise

180° until the cap is in a horizontal position, 6.

37

Water filter

^ After the filter change the filter indicator in the display still flashes.

The change must be be confirmed in the electronic.

Using an external water filter

If your household water supply already has an external water filter installed, leave the standard water filter (bypass cartridge) installed in the appliance.

Confirming the filter change

^ Press and hold the filter change sensor button.

^ At the same time place a finger on the access button. Press and hold both sensor buttons for approx. 5 seconds until a beep is heard.

The water filter change has been confirmed and the filter change indicator had been reset.

The filter change indicator goes out.

^ Close the door.

After installing a new water filter discard the first 24 hours of ice production.

38

Water filter

Trademark/Model Designation

9000 077095

Miele 07134220

Manufacturer: Cuno, Incorporated

State of California

Department of Public Health

Water Treatment Device

Certificate Number

06 1775

Date Issued: March 10, 2006

Date Revised: April 3, 2008

Replacement Elements

9000 077104

07134220

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section

116830 of the Health and Safety Code for the following health related contaminants:

Microbiological Contaminants and Turbidity

Cysts

Turbidity

Organic Contaminants

None

Inorganic/Radiological Contaminants

None

Rated Service Capacity: 740 gals Rated Service Flow: 0.75 gpm

Conditions of Certification:

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

39

Water filter

40

Performance Data Sheet For Filter Model 07134220

Using Replacement Cartridge 07134220

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

NSF/ANSI 42 and 53.

System tested and certified by NSF International in Model 07134220 against NSF/ANSI Standard 53 for the reduction of Cysts and

Turbidity and against Standard 42 for the reduction of Chlorine Taste and Odor; Nominal Particulate Class I.

Note that while the testing was performed under standard laboratory conditions, actual performance may vary.

To a capacity of 739.68 gallons (2800 liters).

Average Permissible Min. NSF

Concentration % Test

Turbidity 10.7 11 + 1 NTU 0.31 97.09 0.5 NTU 0.49 95.42 516456-05

Particulate

Class I Particle size:

> 0.5 to < 1 um 5700000

Chlorine taste and odor 1.9

At least 10,000 particles/ml

2.0 mg/L ± 10%

* Based on the use of Cryptosporium parvum oocysts

Application Guidelines/Water Supply Parameters

Water pressure 30- 120 psi (207 - 827 kPa)

Water temperature* 33°F - 100°F (0.6°C - 38°C)

Service flow 0.75 gpm (2.83 lpm)

30583

0.05

99.52

97.3

CAUTION: To avoid property damage due to water leakage, you MUST read and follow these operating instructions before installation and use of this product.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the

system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

NSF is a registered trademark of NSF International.

CUNO is a trademark of 3M Company used under license.

© 2007 3M Company. All rights reserved.

> 85%

> 50%

69000

0.06

98.9

96.84

511079-03

511081-03

IMPORTANT: Must be installed and operated in accordance with application guidelines.

Failure to do so may void warranty.

Change filter at least every 6 months.

Flush new cartridge for 3 minutes.

For estimated costs of replacement elements please visit your local appliance dealer or parts distributor.

Lead free certificate

This product F 1471 Vi (KIMIWD18US) is tested and certified by WQA against

ORD0902 for California "lead free" compliance.

Miele & Cie. KG

Carl-Miele-Straße 29

D-33332 Gütersloh

41

Frequently asked questions

With the aid of the following guide minor problems can be corrected without a service call.

Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.

Problems with temperature

Issue

The freezer does not get cold.

Possible fault Solution

The machine is not turned on.

Check whether the appliance is turned on at the main switch. The access button must be lit up.

The temperature is too low.

The freezer is too warm.

The machine is not plugged in.

Check that the fuse has not tripped.

Check that the plug is correctly inserted in the power outlet.

Reset the circuit breaker.

A large amount of food is being frozen at the same time.

If the breaker trips again the appliance or the outlet may be defective. Contact Miele or a qualified electrician.

Check the display.

The temperature is set incorrectly.

Select a warmer temperature.

The SuperCool function is still on.

SuperCool automatically shuts off after 52 hours.

The door is not closed.

See "Selecting the correct temperature".

Check that the door has been closed properly.

This makes the compressor run longer, causing the temperature to fall automatically.

The room temperature is lower than the ambient temperature for which the appliance is designed.

Raise the temperature of the room.

Operating the appliance in a room that is too cold will cause the cooling system to switch off for too long, causing the freezer section to become too warm.

42

Frequently asked questions

General problems

Issue Possible fault Solution

Water is flowing out of the appliance.

Close the shut-off valve immediately.

Check whether the water pipe in the appliance is defective.

Contact Miele Technical

Service.

Contact a plumber.

The door will not open.

Check whether the water pressure is too low.

Check whether the correct water valve has been installed.

This is not a fault.

The suction caused by opening and closing the door too many times in succession prevents it from opening.

Self-tapping valves and

3/16" (4.76 mm) saddle valves reduce the water pressure and can block the pipe.

Wait a few minutes, then try again. It should now open without force.

The compressor kicks on very frequently and for too long.

The ventilation slits are covered or dusty.

Clean with a vacuum or brush.

The door has been opened too frequently, or a large amount of unfrozen food has been put in at once for freezing.

Once the freezer gets down to the set temperature the compressor will turn off.

The door is not closed.

Check that the door has been closed properly.

The freezer runs continuously.

To save energy the compressor runs at a lower speed, but for longer when less cooling is required.

The temperature reading in the freezer shows -18°C, although a higher temperature is set.

This is not abnormal. When the ice maker is in use and the temperature of the room is above freezing the temperature automatically stays at -18°C to ensure proper functioning.

43

Frequently asked questions

Alarm / Indicator warnings

Issue Possible fault

The alarm is going off.

The appliance door(s) have been open for longer than 5 minutes.

Solution

Close the door.

The alarm is ringing and the "alarm" indicator is flashing.

The door is not closed.

A large amount of fresh food is being frozen at the same time.

Once the alarm condition has been corrected, the alarm will turn off and the

"alarm" indicator will go out.

There has been a power failure.

The temperature indicator will indicate the highest temperature reached during the alarm. Check that food has not defrosted.

Order replacement filters from Miele.

The filter display is red.

This is a warning that the water filter needs to be changed soon.

The filter display is flashing red.

The "Lock" indicator flashes in the display.

The water filter needs to be changed.

The drip tray for the

Ice/Water Dispenser is full.

See "Exchanging the water filter".

Empty the drip tray by soaking up the water with a sponge or dish cloth.

The control panel has fogged up.

The heating element behind the panel is turned off.

Problems with the ice/water dispenser

Issue

The ice maker will not switch on.

Possible fault

The appliance is not plugged in.

See "Anti-condensation heater" for more information.

Solution

Check that the appliance is connected to the power supply.

After turning on the

Ice/Water dispenser it is not working.

This is not a fault. After opening and closing the door it can take a few seconds to operate.

44

Frequently asked questions

Problems with the ice/water dispenser

Issue Possible fault Solution

The ice maker is not producing any ice.

When the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container.

The appliance is not turned on.

Check that the appliance is switched on.

Contact Miele.

The water supply line was not primed (purged of air) before the appliance was used for the first time.

Check if:

– the Ice/Water dispenser is switched on.

– the Safety Lock is turned on.

– the water supply line is open.

– there are ice cubes stuck together and blocking the exit.

– the ice cube container is in the right position.

– the freezer compartment temperature is too high.

– the water pressure is too low. The water pressure must be between

25 and 80 psi (1.7-5.5 bar).

See "Ice/Water

Dispenser" and/or

"Plumbing" for more information.

Check whether the correct water valve has been installed.

Self-tapping valves and

3

/

16

" (4.76 mm) saddle valves reduce the water pressure and can block the pipe.

See "Anti-clumping".

Check if the Anti-clumping feature is activated. This will ensure that crushed ice or ice cubes do not freeze together.

45

Frequently asked questions

Problems with the ice/water dispenser

Issue

The ice cubes are small.

The Ice/Water has an unpleasant odor/flavor.

The Ice/Water dispenser is not producing ice or water.

Possible fault

Other domestic appliances that use water are in operation.

Check whether the water filter needs changing.

Check the water pressure.

The water pressure must be between 25 and 80 psi

(1.7-5.5 bar).

Check whether the correct water valve has been installed.

Solution

Avoid using such items as a dishwasher, washing machine or shower at the same time.

See "Water filter" for more information.

Consult a plumber.

Self-tapping valves and

(4.76 mm) saddle valves

3

/

16

" reduce the water pressure and can block the pipe.

Use the ice maker more frequently.

When ice is stored for an extended period it may absorb odors, which affects the taste.

Check if the ice cube container is dirty.

Clean the container.

Unsealed packages in the freezer will transfer odor/flavor particles to the ice cubes.

Check that food has been packed in airtight containers.

The Safety Lock is activated. See "Ice/Water Dispenser -

Safety Lock".

46

Frequently asked questions

Problems with the ice/water dispenser

Issue

The ice maker is not producing enough ice or the ice cubes are misshapen.

Possible fault

Check the water pressure. The water pressure must be between 25 and 80 psi

(1.7-5.5 bar).

Check that the freezer temperature is not too high.

Change the water filter.

Solution

Contact a plumber.

See "Selecting the correct temperature".

The Ice/Water dispenser does not appear to be running.

Ice is forming in the supply hose to the ice maker.

A noise is heard periodically from the

Ice/Water Dispenser.

The appliance is not plugged in.

See "Water filter".

Check that the appliance is connected to the power supply.

See "Plumbing".

Check that the freezer is connected to the water supply.

The freezer temperature is too high.

See "Setting the temperature".

Contact a plumber.

Check the water pressure. The water pressure must be between 25 and 80 psi

(1.7-5.5 bar).

Check whether the freezer compartment temperature is too high.

See "Selecting the correct temperature".

The Anti-clumping feature is activated.

See "Anti-clumping" for more information or to deactivate.

47

Frequently asked questions

The appliance is making noises.

Issue Possible fault

Brrrrr...

Blubb, blubb...

Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on.

A gurgling noise can be heard when coolant is circulating through the pipes.

Solution

These noises are not a fault.

The noise of the compressor and the coolant circulating in the system is unavoidable.

Click...

Sssrrrrr...

Clicking sounds are made when the thermostat switches the compressor on and off.

On multi-zone and frost-free appliances you can sometimes just hear the movement of air circulating inside the appliance.

Creaking Creaking sounds can be heard when material inside the appliance expands.

Rattling, vibrating The appliance is uneven.

Realign the appliance using a level, by raising or lowering the screw feet underneath the appliance.

The appliance is touching another appliance or piece of furniture.

Drawers, baskets or shelves are unstable or sticking.

Move it away.

Check all removable items and refit them correctly.

Separate them.

Bottles or containers are unstable or knocking against each other.

The transport cable clips are hanging loose at the back of the appliance.

Remove the clips.

48

After sales service

In the event of a fault which you cannot easily fix yourself, please contact the

Miele Technical Service Department at the address on the back of this booklet.

When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.

MieleCare

(USA only)

MieleCare, our Extended Service

Contract program; gives you the assurance of knowing that your appliance investment is covered by 5 years of worry-free ownership.

MieleCare is the only Extended Service

Contract in the industry that guarantees repairs by a Miele Authorized Service

Provider using genuine Miele parts.

Only genuine Miele parts installed by factory-trained professionals can guarantee the safety, reliability and longevity of your Miele appliance.

Please note that unless expressly approved in writing by the Miele Service department, Extended Service

Contracts offered by other providers for

Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.

To learn more about MieleCare

Extended Service Contracts, please contact your appliance dealer or visit us online at: http://mieleusa.com/mielecare

49

50

Installation Instructions

Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.

To prevent accidents and machine damage read these instructions before installation or use.

51

Caring for the environment

Disposal of packing materials

The cardboard box and packing materials are biodegradable and recyclable. Please recycle.

Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation!

Disposal of an old appliance

Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials.

Before discarding an old appliance, disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard.

52

Installation

Have the appliance installed by a qualified technician, according to the enclosed installation instructions.

Installation site

The appliance should be installed in a dry, well ventilated room.

WARNING

This appliance is top-heavy and must be secured to prevent it from tipping forward.

Keep the door closed until the appliance is completely installed and secured as per the installation instructions.

Empty weight of your machine:

F 1471 Vi . . . . . . . . . . 306 lbs (139 kg)

Do not install the appliance:

- outdoors,

- in an environment with dripping water,

- in rooms which are at risk of frost.

The installation location should not be exposed to direct sunlight, nor near a heat source, such as an oven, radiator, etc.

The ambient temperature should not drop below 55°F (13°C) or rise above

110°F (43°C), otherwise malfunctions may occur.

If installation next to a heat source is unavoidable observe the following minimum distances from the heat source:

– 1

1

/

4

" (3 cm) from an electric cooktop or electric oven.

– 12" (30 cm) from a gas or oil cooktop, range or oven.

The following should also be taken into consideration:

– The electrical outlet must be easily accessible in case of an emergency,not concealed behind the appliance.

– The plug and cord must not touch the rear of the appliance as they could be damaged by vibrations from the appliance.

– Do not plug in other devices behind this appliance.

53

Installation

Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.

– If the room is too cold, it will cause the cooling system in the appliance to remain off for too long.This can cause the temperature in the appliance to rise, resulting in damage.

54

Installation

Base

A fully loaded appliance is very heavy.

The load-bearing capacity of your floor must meet the following requirements.

The approx. weight of a fully loaded machine is:

F 1471 Vi . . . . . . . . . . . 503 lbs (228 kg)

To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.

If in doubt, contact Miele.

Furniture/fixtures

The new appliance will be mounted securely to adjacent and overhead furniture/fixtures.

For this reason it is essential that all attachable furniture/fixtures are connected securely to the base or the wall by suitable means.

Ventilation

The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis.

Installation niche

To ensure safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation dimensions. See "Niche dimensions".

The side walls of the installation cavity must be plumb.

The minimum thickness of the side walls and the top wall must be

5

/

8

"

(16 mm).

The minimum thickness of the toe-kick panel must be ½" (13 mm). A thickness of

3

/

4

" (19 mm) is recommended.

55

Installation

Stainless steel panels

Stainless steel door panels and toe-kick covers are available from Miele.

Custom door panels

This appliance is compatible with all styles and designs of kitchen cabinetry.

The total weight of the decorative panel(s) must not exceed the following:

F 1471 Vi . . . . . . . . . . . 143 lbs (65 kg)

Side-by-side

This appliance can be installed

"side-by-side" with another fridge/freezer using a "Merging Kit".

The "Merging Kit" is available from

Miele.

Contact Miele or your dealer for specific information about which combinations will work with your appliance.

Fitting a door panel which is heavier than the max. permitted could damage the hinges.

For instructions on how to attach the appliances and install the heating mat, please refer to the instructions included with the "Merging Kit", available from Miele.

Installation options

There are many different installation options. You are limited only by the design of the kitchen.

Installation without a partition using the "Merging Kit"

The door hinge cannot be exchanged.

Single column

The appliance can be installed at any preferred location in the kitchen.

However, be sure the door will open and close properly in the chosen location.

If the appliances are installed directly next to each other (without a partition), they need to be attached together using the "Merging Kit".

56

Installation with partition using the

"Merging Kit"

The minimum thickness of the partition is 5 /

8

" (16 mm).

Installation

Side panels

If one side of the appliance is visible, a side panel must be used.

The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity.

The dimensions of the side panel are taken from the opposite wall of the installation space. During installation, ensure that the cavity is square and the measurements are correct.

If there is a partition with a thickness from

5

/

8

" (16 mm) to 6

5

/

16

" (160 mm) between the adjacent appliances, then each appliance should be individually installed within its own niche using the mounting accessories included.

The "Merging Kit" will also be needed.

The "Merging Kit" is available from

Miele.

Installation with partition without using the "Merging Kit"

If there is a partition with a thickness of more than 6

5

/

16

" (160 mm) between the adjacent appliances, then each appliance should be individually installed within its own niche using the mounting accessories included (the

"Merging Kit" is not necessary).

57

Installation

Door dimensions (open 115°)

The dimensions of the door fronts and handles will vary according to each individual kitchen.

F 1471 Vi 20

A

11

/

16

"

(525 mm)

B

Door front max.

1 1/2" (38 mm)

C

Door handle

D

9

3

/

16

"

(234 mm)

Miele recommends using the full door opening angle of 115° for this freezer.

58

Niche dimensions

Installation

Niche width (A)

F 1471 Vi 18" (457 mm)

59

Installation

Power supply and water connection

1. Power supply

2. Water connection

F 1471 Vi

A

9" (229 mm)

Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2

and 609.10) Never install or operate where inlet water pressure may exceed

120 psi.

Door front dimensions

60

Installing the appliance

Before you begin

Read these instructions completely and carefully.

Have the appliance installed by a qualified technician, according to the enclosed installation instructions.

– Multi-grip pliers

– Level

– Tape measure

– Square

When fastening the cabinet to the wall behind it (see "Installing the appliance") use:

– suitable plugs/screws depending on the type of wall.

– several mounting brackets, if required.

To reduce the risk of injury or damage to the product, two people should be used for installation.

These installation instructions are intended for use by qualified installers.

In addition to these instructions, the appliance must be installed in accordance with all local codes, or in the absence of a local code.

– In the USA, in accordance with the

National Electric Code,

ANSI/NFPA 70 - latest edition/State and Municipal codes and/or local codes.

– In Canada, in accordance with the

Canadian Electric code C22.1 - latest edition/Provincial and Municipal codes and/or local codes.

Other

– Stepladder

– Dolly, hand truck

– Wooden beam (cross section min. 3" x 4" [75 mm x 100 mm] as an alternative tilt protection, length depends on the width of the installation niche)

– Wood screws in different sizes

– Edge protector(s)

Optional accessories

– "Merging Kit" for side-by-side installation

– RemoteVision module for wireless monitoring

Tools needed for installation

– Cordless screwdriver

– Torx screwdriver

– Hammer drill

– Wood drills in different sizes

– Hammer

– Rachet 5/16" (8 mm)

– Adhesive tape

61

Installing the appliance

Aligning the housing unit

The housing unit must be carefully aligned using a spirit level before installing the appliance. The unit corners must be at right angles, as otherwise the furniture door will not align correctly with the 4 corners of the appliance.

– The side panels of the housing must be even.

– The housing unit panels must be at least 16 mm thick.

– The plinth facing must be at least 13 mm thick (or preferably 19 mm).

Check the installation niche

To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements.

^ Check the base (see "Installation").

^ Check the dimensions of the cavity.

^ Check that the cavity is square.

^ Check the location of the power outlet.

^ Check the location of the water connection (see "Plumbing").

^ Check that all furniture parts in the vicinity of the appliance are securely connected to the wall.

^ Check that the adjacent furniture/fixtures do not collide with the open door.

Before installation

,

Caution - the appliance is very heavy. Use caution when unpacking and opening the door, danger of tipping.

^ To protect the base from damage during installation, attach a hard board, linoleum, etc., to the floor in front of the intended installation location.

^ Take the supplied accessories out of the protective packaging.

62

^ Do not remove the installation supports from the appliance door.

They will be used later in the installation niche.

There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged.

^ Check the appliance for damage in transit.

Do not install the appliance if it is visibly damaged. If in doubt, contact your dealer.

Installing the appliance

^ From the rear of the appliance carefully lift it from the pallet.

Once the appliance is on the ground it can be wheeled around.

^ Loosen the bracket that holds the appliance to the pallet.

Caution! The appliance is no longer secured and may be unstable.

63

Installing the appliance

RemoteVision module installation

(optional accessory)

Always disconnect the appliance from the power supply when performing installation, maintenance or service work.

Install the RemoteVision module before placing the appliance in its installation niche.

Once connected the RemoteVision module will increase the energy consumption of the appliance.

The slot for the RemoteVision module is located in the lower area of the back of your appliance.

^ Unscrew the screws a on the cover b and pull off the sticker c.

^ Remove the cover b.

64

Installing the appliance

^ Push the module into the slot until it locks into place.

^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on.

The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed.

If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele.

^ Pull the antenna d straight out.

^ Guide the cover b over the antenna d and screw on the cover.

^ Angle the antenna d so that it faces to the right or left.

If necessary, disconnect the power supply and continue installing the appliance.

Preparing the installation niche

,

Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard.

Because of the size and weight of the appliance, it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche.

65

Installing the appliance

Mounting Accessories

The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically.

The bag needed for each step will be marked with its respective letter.

Anti-tip brackets

The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping.

Two anti-tip brackets are recommended for each appliance. For side-by-side installations 4 brackets are recommended.

^ Position the anti-tip brackets on the left and right in the installation niche so that there is no more than 3/8"

(10 mm) of space between the brackets and the side walls.

^ Mark the drill holes in the anti-tip brackets on the back wall and on the ceiling of the installation niche.

^ Set the brackets aside - they will be needed again later.

,

Risk of tipping

The installation niche must be securely attached to the wall behind it with multiple brackets. This is the only way the appliance, which is later secured in the niche, can be prevented from tipping!

Screws are supplied with the appliance for various applications/materials.

If the anti-tip brackets cannot be attached securely with the screws supplied, an alternative anti-tip device can be used.

Ensure that there are no electrical wires or plumbing in the area which the screws could penetrate - risk of injury and damage.

66

^ Now attach the installation niche to the wall.

The built-in cabinet must be secured to the wall behind it with several screws.

In a cabinet with a back wall

Installing the appliance

In a cabinet without a back wall

^ screw the back wall of the cabinet in several places directly to the wall behind it.

For this, use suitable plugs/screws depending on the type of wall.

^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.

For this, use suitable plugs/screws depending on the type of wall.

67

Installing the appliance

Securing an alternative anti-tip device

If the anti-tip brackets cannot be attached securely using a wooden beam, an alternative anti-tip device can be used.

Ensure that there is no "give" between the appliance and the anti-tip device.

^ Mark the installation height (lower edge of the beam) on the rear wall of the niche.

^ Select screws according to the thickness of the wooden beam.

If possible, always screw the wooden beam to existing studs.

Determine the number of screws based on the niche width, to ensure that the beam will be attached securely.

^ Locate wall studs near the rear wall of the niche and mark the drill holes in the beam accordingly.

^ Pre-drill the wooden beam.

^ Attach the wooden beam to the rear wall of the niche.

Now prepare the water connection from the appliance to the main supply line (see "Plumbing").

– The wooden beam must be at least .

3" x 4" [75 mm x 100 mm] thick.

– The length is equal to the width of the installation niche.

– If the installation niche is deeper than the appliance, use a thicker wooden beam or attach two beams.

– The beam must cover the appliance by at least 2" (50.8 mm).

68

Sliding the appliance into the installation niche

If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit".

Installing the appliance

^ Plug the appliance into the power outlet a.

The plug of the appliance should be easily accessible after installation.

If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.

^ Unscrew the plinth.

In the case of side-by-side installations, a separate outlet must be used for each appliance.

^ To prevent the power cord from becoming caught:

Tie a piece of string to the middle of the power cord and feed it forward under the appliance. When sliding the appliance in, pull the cable forward b.

^ Carefully slide the appliance into the space.

If resistance is felt when attempting to slide the appliance into the installation niche - for example, because the floor is uneven,

^ Turn the rear adjustable wheels slightly outward (see "Aligning the appliance"), then push the appliance in.

Be careful not to damage the water pipe or power cord attached to the floor.

^ Remove the edge protectors.

^ To protect the corners of the installation space, attach edge protectors where needed (not included).

69

Installing the appliance

Aligning the appliance

^ Align the appliance with the custom front.

Important!

When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right.

– Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84"

(2134 mm).

The installation aids c on the appliance door have been designed for the following custom door thicknesses:

– 3/4" (19 mm)

– 1 1/2" (38 mm).

The height-adjustable feet at the front and rear can all be adjusted from the front:

– Front feet:

Adjust with a rachet 5/16" (8 mm) d.

– Rear feet:

Adjust with a (cordless) screwdriver and/or a rachet 5/16" (8 mm) for fine adjustment e.

^ Use a level to align the installation aids c on the door.

^ Align the appliance again using a level.

Note:

– When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right.

– If using a wooden beam as an alternative anti-tip device, rotate the appliance all the way toward the wooden beam.

70

Installing the appliance

Attaching the appliance to the installation niche

^ Secure the attachment plate side lugs.

^ Screw the attachment plate lugs f to the overhead furniture/fixtures.

If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche.

^ If necessary, shorten the filler strip h to the required height.

^ Place the 2 strips on top of each other i.

^ Insert the filler strip until you hear it click into place j.

^ Pull out the plate side lugs g.

71

Installing the appliance

For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip:

^ Open the appliance door.

^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance.

^ Place the second filler strip on the peg and press both filler strips together.

^ Click the filler strips into place above the appliance.

^ Screw the attachment plate lugs k to the adjacent furniture/fixtures.

With side-by-side combinations, only the external side of the appliances can be secured to the niche.

Now connect the water supply to the appliance (see "Plumbing").

72

Preparing the custom door

Installing the appliance

^ Load the door basket.

^ Open the appliance door.

^ Unscrew the installation supports l from the appliance door.

^ Loosen the remaining screws from the strips m on each side of the door, then remove.

^ Set aside the screws and side strips m - you will need them again later.

^ Remove the light switch cover (see arrow).

^ Measure the distance X between the bracket from the door and the overhead furniture/fixtures.

^ Loosen the two nuts.

Set aside the nuts - you will need them again later.

^ With the inside facing up, lay the custom door on a stable surface (to avoid scratch marks, place some plastic or a cloth on the surface).

73

Installing the appliance

^ Mark the distance X on the back-side of the custom door.

^ Also calculate and mark the center of the custom door Y.

^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door.

^ Pre-drill the holes.

^ Tightly screw on the bracket using the pre-drilled holes:

Attach the bracket to each attachment point with at least one screw.

The bracket includes a variety of holes for the various design options of custom doors.

When performing work on the custom door, always observe the following:

– Always select the best load-bearing surface of the custom door as the location for screws.

– Always select a screw length that is shorter than the thickness of the door front.

^ Secure the door handle to the front of the appliance from the inside.

^ Attach the bracket at the top with at least 6 screws.

74

Attaching and aligning the custom door front

Installing the appliance

^ Open the door and hang the custom door with the mounting frame over the threaded bolts n.

^ Put the side strips m back into place and screw them completely down on both sides of the appliance door.

Bag E contains spare screws for this purpose.

^ Screw the nuts o a few turns onto the threaded bolts n. Do not tighten the nuts completely.

^ Close the appliance door and check the distance to doors of adjacent furniture/fixtures.

^ Align the custom door height with the threaded bolts n.

^ Now tighten the nuts o on top. This secures the appliance door.

75

Installing the appliance

Attaching the covers

^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door.

^ Insert the cover strip into the space between the appliance and the side panel.

For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only.

^ Screw the brackets onto both sides of the appliance, to hold the cover strip.

76

^ Attach the light switch cover.

Installing the appliance

Attaching the toe-kick cover

The maximum height of the toe-kick cover is 4" (102 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.

^ If required, cut the toe-kick cover to the required length and height.

Mounting the air separator

The air separator on the inside of the freezer door keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit.

^ Attach the plinth to the appliance, and put the included cover plates in place.

^ If necessary, shorten the three parts of the air separator.

^ Insert the foam pieces back into the sides.

^ Open the freezer door.

^ Attach the toe-kick cover to the plinth.

^ Wedge the air separator at the bottom of the freezer door, so it connects in place.

77

Installing the appliance

Aligning the Ice/Water

Dispenser

If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance.

,

Disconnect the appliance from the power supply.

^ Remove the cover and the plastic grill.

^ Press the dispenser back and pull downwards to remove.

^ Remove the screw from the rear casing, then lift the tab on the drip tray up and off.

78

Installing the appliance

Once the drip tray has been removed, the four metal strips can be used to align the Ice/Water Dispenser.

^ Pull the rear cover forward and out.

^ Loosen the water sensors and carefully bend them upwards.

^ Loosen the screws of the four metal strips.

^ Insert a screwdriver into one of the four slots and push sideways until the dispenser is aligned with the custom door (the gray arrow will adjust to the rear; the black arrow will adjust front).

^ Re-tighten the screws of the strips.

^ Insert the drip tray back into place, then clip the water sensors back into the position.

^ Replace the rear cover, panel and screw.

^ Replace the drip tray and cover.

^ Finish by putting the plastic grill, cover, and dispenser back into place.

^ Carefully remove the drip tray using a screwdriver if necessary.

79

Installing the appliance

Attaching the frame and the shelf

The word "TOP" is marked on the rear of the frame at the top.

For

3

/

4

" (19 mm) thick custom doors:

^ Slide the cover frame onto the

Ice/Water Dispenser and press until it is flush with the door front.

For 1 1 /

2

" / (38 mm) thick custom doors:

^ Fit the extension trim onto frame.

^ Fit the cover frame onto the Ice/Water

Dispenser and press it firmly into position until it is flush with the door surface.

80

Plumbing

All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations.

Disconnect the appliance from the electrical power supply before connecting it to the water supply.

Turn off the water supply before connecting the water lines to the ice cube maker.

The shut-off valve for the water connection must not be located behind the appliance. It is recommended to place the shut-off valve directly next to the appliance

(base unit) or in another easily accessible location.

Do not use pipe extenders.

In the event that the piping has to be replaced only Original Miele Spare parts are suitable for use. Contact

Miele.

The water quality must conform to country requirements for drinking water.

– The appliance is only suitable for connection to the cold water supply.

– The water pressure must be between

25 and 80 psi (1.7-5.5 bar).

– A separate shut-off valve must be installed, so that the water supply can be interrupted as needed.

– The maximum outer diameter of the water pipe (without fittings):

3

/

8

" (10 mm).

81

Plumbing

Preparing the water connection

For appliances with a hose guide

The connection to the household water supply must be installed before the appliance is installed.

^ Turn off the main water valve to prevent damage caused by leaking water.

^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit.

^ Install the connecting pipe. Always observe the indicated clearance dimensions to prevent damage to the connecting pipe when pushing in the appliance.

^ position the device in front of the niche and push the stainless steel tube through the hose guide at the back of the unit.

At this point the niche should be ready for the appliance to be pushed back into it (see "Installing the appliance").

^ You can now continue with the installation.

^ Secure the connecting pipe to the floor with adhesive tape.

^ You may now proceed to install the appliance. See "Installing the appliance".

82

Plumbing

Connecting the water supply

When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit.

When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage.

Use bending aids.

^ Push the union nut and seal onto the water pipe.

^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand.

^ Then use an open-ended wrench to tighten the union nut. Do not over tighten.

^ Open the shut-off valve and the main water connection. Check for leaks at the connection for the shut-off valve and to the appliance.

^ Turn the appliance on.

After a maximum of 10 hours the first ice cubes will drop out of the ice cube maker and collect in the ice cube container.

^ Remove the cap from the appliance connection, 1.

^ Bend the water pipe to suit the location of the connection on the appliance, 2.

83

Electrical connection

,

Avoid the risk of electrical shock

- Plug into a grounded 3-prong outlet.

- Do not move the ground plug.

- Do not use an adapter.

- Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Improper connection of the equipment grounding conductor may result in electric shock. If you are in any doubt as to whether the appliance has been properly grounded, have the appliance checked by a qualified electrician or service technician.

Installation, repairs and other work by unqualified persons could be dangerous.

Before installing the appliance, verify that the voltage, load and circuit rating information found on the data plate match the household electrical supply.

If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele

Technical Service.

U1-800-999-1360

V1-800-565-6435

The appliance is supplied with a

UL-listed, 3-wire power cord and

NEMA 5-15 P plug ready for connection to a 120 V, 60 Hz supply.

The fuse rating is 15 amps.

The appliance requires a 3-wire receptacle.

The receptacle must be installed by a licensed electrician only.

In the case of side-by-side installations, a separate outlet must be used for each appliance. Ideally, the power outlet should be next to the appliance and easily accessible. Do not connect the appliance to the power supply by an extension cord. Extension cords do not guarantee the required safety of the appliance (danger of overheating).

If any changes are needed to the household wiring or power supply, this work must be performed by a qualified electrician.

84

RemoteVision (optional accessory)

Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.

For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual.

Be sure your wireless system meets the following requirements

– A wireless router that supports an

IEEE 802.11b protocol

– Windows XP

® system, Mac ® or newer operating

OS X 10.3 or higher

– Cable or DSL modem

– Microsoft

®

Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox

1.5 or higher

* Please note that each wireless router manufacturer supplies their own device drivers and setup programs. Due to the differences in manufacturers, exact router setup instructions are not included in this manual. Wording and instructions may vary.

85

RemoteVision (optional accessory)

Accessing the RemoteVision control panel

^ Touch the access button "p" so it turns yellow.

^ Note the position of the X button, but do not touch.

^ Touch the access button "p" again so it turns white.

Only the access button " p" is visible.

^ Place one finger on the position of the

X button and hold (the X button will not be visible).

^ While holding down the X button, press the access button " p" once.

Keep holding the

X button down until the following appears in the display

(approx. 5 seconds).

Access to the Custom settings mode is now active for approximately 10 seconds.

^ Tap the X button until ; appears in the display.

^ Touch the access button "p" to confirm.

See the table on the following page for a description of each setting in the display.

^ Use the Y or X buttons to select the

RemoteVision options.

The module has been connected to the network when display.

If

; # appears in the

; # does not appear, refer to the

"Network options" section of the

XKM 2000 Installation Instruction manual.

^ Press and hold the access button "p" for 2 seconds to confirm the change.

^ To return to the main menu, tap the X button until a solid

; - appears in the display.

^ Press the access button "p" to confirm.

^ Tap the X button until a ; appears in the display.

^ Touch the access button "p".

You have left the Custom settings mode.

When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.

86

RemoteVision (optional accessory)

MasterCool control panel options for RemoteVision

Status indicators Description of function

Flashing ; ~

Flashing ; ‡

Flashing ; |

Module booting phase

Not connected to network

Connection to network established, no IP address assigned

Solid ; #

Flashing ; <

Flashing ; =

Connected to network

In Ad-Hoc Mode, not connected

In Ad-Hoc Mode, connected

Selectable options

; -

; 2

; 3

; 4

Description of function

Back

Reboot the module

Reset to factory settings

Enter Ad-Hoc Mode

Note: If you cannot select any option (other than

; - "Back", the module has not been installed correctly.

87

Alteration rights reserved / 0414

INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST

CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.