Installation Instructions 6540.140 6540.160 6540.168 6540.170 6542.140 6542.170 SPREAD LAVATORY FAUCETS 6542.145 6540.175 6542.175 6540.270 6540.275 6540.278 6540.277 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. Certified to comply with ANSI A112.18.1M M968508 (11/15) To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Recommended tools Screwdriver 1 Channel Locks SPOUT OR BASE ASSEMBLY Tubing Cutter Adjustable Wrench CAUTION Turn off water at main supply. Insert SPOUT SHANK (1) through center hole of mounting surface, making sure RUBBER GASKET (2) is properly positioned in SPOUT BASE (3). Assemble RUBBER WASHER (4), BRASS WASHER (5), and LOCKNUT (6) onto threads of SPOUT SHANK (1) from underside of mounting surface. Align SPOUT (7) and tighten LOCKNUT (6). Be sure slot in BRASS WASHER (5) is positioned to the rear as shown. 7 3 2 1 1a TO CHANGE SPOUT TO A SWIVEL SPOUT: 4 Unscrew SPOUT NUT (8) and remove SPOUT (7). Take SPOUT CLIP (9) off SPOUT (7) and remove RUBBER RING (10). 5 Replace RUBBER RING (10) with seperate PLASTIC RING (11) packed with faucet. 6 Put SPOUT CLIP (9) on SPOUT (7). Reassemble SPOUT (7) to SPOUT BASE (3). 7 8 10 9 3 11 2 VALVE ASSEMBLY WITH FLEXIBLE HOSE VALVE CONNECTIONS Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks. Insert VALVES (5) into mounting holes from underside of ledge. Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop. 10 11 Tighten LOCKNUT (1) to secure VALVE (5) position. 10 11 3 11 5/16'' MIN. 5 MOUNTING LEDGE 8 5 10 MOUNTING SURFACE 7 2 1 HOT 5 3 2 1 COLD 2a WATER SUPPLY CONNECTIONS Press TEE (8) onto SPOUT SHANK (5) making certain that the O-RING (9) is properly seated on SPOUT SHANK (5). Push COUPLING (4) into TEE (8) and attach to SPOUT SHANK (5) and tighten. Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A). Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE SUPPLIES (2) (not included. Use adjustable wrench to tighten connections. Do not over tighten. Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK. 5 9 8 1A 6A 7A COUPLING NUT 1 1/2" PIPE THREAD 2 HOT 7 6 FLEXIBLE SUPPLIES 4 3/8 O.D. BULL-NOSE RISERS COLD 3 COMPRESSION NUT FERRULE 3/8 COMPRESSION CONNECTION M968508 (11/15) 2b VALVE ASSEMBLY WITH RIGID VALVE CONNECTIONS Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks. Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge. 10 Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to SPOUT SHANK (7) and tighten. 11 Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop. 10 11 Tighten LOCKNUT (1) to secure VALVE (5) position. Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten COUPLING NUT (14) firmly. 3 MOUNTING LEDGE Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector. 10 11 5/16'' MIN. 5 8 5 2 1 MOUNTING SURFACE HOT 3 2 1 7 13 14 4 14 5 13 6 9 COLD 3 PUTTY Apply a bead of PUTTY around underside of DRAIN FLANGE (1) flange. Insert DRAIN PLUG (2) into SINK drain hole. Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4), and LOCKNUT (5) from underneath sink. Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG. Connect other end to trap. 4 1 DRAIN ASSEMBLY (6542.140/.170) Turn VALVES (1) to off position. SINK 2 3 4 5 SEALANT 6 5 7 6 INSTALL HANDLES 2 Insert ADAPTOR (8) with larger diameter over the VALVE STEM (4). Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4). Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into hot valve (left side). Insert HANDLE SCREW (7) into HANDLES and tighten with screwdriver. 7 5 3 8 4 1 Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Turn handles into OFF position and replace AERATOR. TEST INSTALLED FAUCET Remove AERATOR. With handle in OFF position, turn on water supplies and check all connections for leaks. 6 SERVICE STOP WASHER 90° To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and BONNET NUT. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace BONNET NUT, HANDLE, SCREW, and INDEX. AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean. If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. SPRING CLIP Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then: Remove HANDLE and BONNET NUT. CARTRIDGE Remove CARTRIDGE by pulling up. Thoroughly rinse plastic SCREEN at base of CARTRIDGE. Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace BONNET NUT, HANDLE, SCREW and INDEX. SCREEN CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M968508 (11/15) SPREAD LAVATORY FAUCETS MODEL NUMBERS M919646-0020A 5" SPOUT M953429-0020A 8" SPOUT 051211-0070A INDEX KIT 066114-0020A AERATOR, 0.5gpm M922858-0020A AERATOR, 0.35gpm M922880-0020A AERATOR, 1.5gpm 000690-0020A HANDLE SCREW 051210-0020A LEVER HANDLE M918014-0070A ADAPTER 051211-0070A INDEX KIT M964478-0020A 6" WRIST BLADE HANDLE (6400.160, 6400.168) 051336-0020A AERATOR VANDAL PROOF KIT 051322-0020A VANDAL PROOF SCREW 012087-0070A SPOUT SEAL KIT 000690-0020A HANDLE SCREW 051217-0020A 4" WRIST BLADE HANDLE M918014-0070A ADAPTER 6540.140 6540.160 6540.168 6540.170 6542.140 6542.170 6542.145 6540.175 6542.175 6540.270 6540.275 6540.278 6540.277 033757-0070A TEE MOUNTING KIT M918014-0070A ADAPTER A911748-0070A SPOUT GASKET 904939-0020A BONNET NUT 951764-0070A CARTRIDGE 030256-0070A SPOUT MOUNTING KIT 051212-0020A ESCUTCHEON KIT 051213-0070A VALVE MOUNTING KIT M970033-0070A FLEXIBLE HOSE & TEE KIT 012112-0070A TUBE SEAL & COUPLING KIT 033757-0070A TEE MOUNTING KIT 024220-0070A COUPLING NUT 012111-0070A TUBE & TEE KIT 015025-YYY0A DRAIN COMPLETE 070532-0040A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 10:00 a.m. to 4:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-1200 Appropriate finish code CHROME Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2015 002 M968508 (11/15)
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021