Lever Arm and Float Controls Series 40-41 46-47

Lever Arm and Float Controls Series 40-41 46-47
pg118
3/8/05
4:44 PM
Page 1
Series
40-41
46-47
49
Lever Arm and Float Controls
®
®
ADJUSTABLE
STOP
2 BRASS FLOATS
5-1/2 HIGH [139.7]
2-1/8 DIA. [53.97]
46-47
SERIES
40-49
SERIES
ADJUSTABLE
STOP
41 SERIES
Level
LEVER OPERATED CONTROLS
To Open/Close Circuits by Mechanical Movement
Snap-Action Type 46 (General Purpose NEMA-1)
Used where positive mercury switch action is desired when the operating lever is moved to a particular position (see Chart C for various circuits available). The mercury switch does not move until the
operating arm has moved a definite amount at which time it
“snaps” to its alternate position.
Direct-Action Type 47
(General Purpose NEMA-1)
Used where greater sensitivity and more over-travel is desired.
The mercury switch is mounted on the lever and moves with it. Requires less force and travel than the snap-action type. See Chart C
for switch operations.
Direct Action with Spring Return-Type 47SR
For same application as Type 47 except this control is equipped
with the spring return feature. The mercury switch is mounted on
the lever arm with a spring assembly which returns the arm to the
“Center” position when force is removed from the lever arm.
FLOAT CONTROLS
For vessels not under pressure
Type 40-49
For use with rods and floats to open/close mercury switches by a
change of liquid levels in vessels not under pressure. Example: to
start and stop motor operated pumps, or perform other functions
in changes of liquid level.
Type 40 Counter Balanced Snap-Action Movement
For general applications. The float assembly slides up and down
the float rod. When the float rises to the top stop, it moves the operating arm up, and when it drops to the bottom stop, it moves the
operating arm down. The mercury switch does not move until the
operating arm has moved a definite amount, at which time it
“snaps” to its alternate position. For minimum liquid level changes,
see Chart C. Enclosure is NEMA-1 general purpose.
Type 49 Counter Balanced Direct Action
For use where closer differential in level change is desired between
on and off operation. The mercury switch is mounted directly on
the operating lever and moves with it. This control requires less operating force than the snap-action type. For minimum liquid level
changes, see Chart C. Enclosure is NEMA-1 general purpose.
Type 49SRC Counter Balanced Direct-Action with Spring Return
Similar to Type 49 except spring return assembly added to provide
for stage operation. The spring return assembly holds the arm in a
neutral position (contacts either open or closed) until the float engages upper or lower stop on rod, and actuates control contacts.
Can be used for high or low alarm. Enclosure is NEMA-1 general
purpose.
Standard Features
Standard Features
General Purpose-Types 46, 47, 47SR: 4-3/4 dia. steel case finished
gray enamel. Glass fronted cover. Outlet box has 1/2 knockouts on
both sides. Standard with bottom mounting base plate having two
13/64 holes 3 apart. 41⁄2 lever arm extended to right with seven
lever holes 1/2 Centers.
General Purpose-Types 40, 49, 49SRC: 4-3/4 dia. steel case finished gray enamel. Glass fronted cover. Outlet box has 1/2 knockouts on both sides. Standard with bottom mounting base plate
having two 13/64 holes 3 apart. Standard Construction: Furnished with bottom mounting and with lever arm extended to
right.
Type 41 Plunger Type Snap-Action
For use on closed tanks (cannot be used on pressurized tanks). Rod
and floats same as Type 40 except maximum rod length 4 ft. For
minimum liquid level change, see Chart C. Standard Construction:
Furnished with 1/4 NPT Bottom Connection only. Enclosure is
NEMA-1 general purpose. For Weather Resistant NEMA-3 Case,
specify Type 41W. When ordering, specify Type No. and Circuit.
Example: Type 41 - 156. Can be used for pump operation or day
tanks.
128
Dwyer Instruments, Inc. P.O. Box 373/Michigan City, Indiana 46361/Phone 219 879-8000/Fax 219 872-9057 • U.K. Phone (+44) (0)1494-461707 • Australia Phone 61 2 4272-2055
pg119
3/8/05
4:45 PM
Page 1
MODEL CHART – SERIES 40-49
40
40
2
2
R6
49
49
4821
R6
4849
Series Designator. Counter balance lever arm operated control with adjustable deadband. Minimum deadband approximately 2 (51 mm),
maximum deadband 20 ft. (6 M). Operates with Two 2-1/85-1/2 (54140 mm) diameter brass floats with rod length up to 8 ft; or
Three 2-1/25 1/2 (54140 mm) brass floats for 8 to 20 ft (2.44 to 6M) rod. Float, (Float type, size and rod length must be specified
on order). Has mercury switch with “snap action” movement assembly. General purpose case only.
Mercury switch circuit. See Chart C.
Indicates lever is to the right, and has bottom flange for mounting.
Float and Rod assemblies must be ordered separately. See Chart A. For minimum deadband see Chart B.
R6
Similar to Type 40 Series, except mercury switch is mounted directly on operating arm providing closer minimum deadband of 7/8 (22 mm).
Mercury switch circuit. See Chart C.
Indicates lever is to the right and has bottom flange for mounting.
Float and Rod assemblies must be ordered separately. See Chart A. For minimum deadband see Chart B.
2
CHART A – FLOATS AND RODS FOR SERIES 40, 41 AND 49
37 - 29
37 - 43
MODEL CHART – SERIES 46-47
46
46
2
R6
4821 R6
48xx
47SRC
47SRC
R6
4821 R6
48xx
R6
CHART B – MINIMUM LIQUID LEVEL CHANGES (WATER)
TYPE
NO.
40
41
49
49SRC
MAX. ROD
LENGTH
20 Ft. (6 M)
4 Ft. (1.22 M)
20 Ft. (6 M)
20 Ft. (6 M)
TWO 2-1/8 (54MM) O.D. ONE 4-1/2 (114 MM) O.D.
BRASS FLOATS
COPPER OR SS FLOAT
2 (51 mm)
1 1/2 (38 mm)
4 (102 mm)
1 1/2 (38 mm)
7/8 (22 mm)
1/2 (13 mm)
1 1/2 (38 mm)
3/4 (19 mm)
LEVER ARM OPERATED CONTROLS
Series Designator. Lever arm operated control. Deadband approximately 2 (51 mm). Has mercury switch with “snap action” movement assembly. UL
General purpose case only.
Mercury switch circuit. See Chart C.
Indicates lever is to the right, and has bottom flange for mounting.
CSA
Similar to Type 46 Series, except mercury switch is mounted directly on operating arm providing closer minimum deadband of 7/8 (22 mm).
Mercury switch circuit. See Chart C.
Indicates lever is to the right and has bottom flange for mounting.
UL
CSA
Similar to Type 47 except has spring return to hold lever arm in center (internal) position until the lever actuates engages upper or lower stop
actuating mercury switch.
Mercury switch circuit. See Chart C.
Indicates lever is to the right and has bottom flange for mounting.
Other circuits available. Consult factory.
UL
CSA
CHART C
ORDERING INFORMATION:
SWITCH ACTION
LEVER
DOWN
“A” OFF
“A” ON
“A” ON
“B” ON
“A” OFF
“B” OFF
“A” OFF
“B” ON
“A” OFF
“B” ON
“A” OFF
“B” ON
“A” OFF
“B” ON
CSA
R6
2
47
47
UL
CENTER
ON
ON
OFF
OFF
ON
OFF
LEVER
UP
ON
OFF
OFF
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SNAP-ACTION
TYPES
40, 41 OR 46
DIRECT-ACTION
TYPES
47, 49, 47, 49SRC
ADD SUFFIX
-2
-3
ADD SUFFIX
-4821
-4820
UL
UL
CSA
CSA
-103
-4814
UL
CSA
-127
-4813
UL
CSA
-156
-4815
UL
CSA
-4823
UL
CSA
-4849
UL
CSA
-4805
UL
CSA
Other Switches or Combination of Switches are Available, consult factory.
ELECTRICAL RATING — ALL TYPES
Standard type 9-51 switch. Each switch AC or DC 10A. 120V., 5A,
240V., Motor Rating 120/240V 3/4 hp. single phase AC 1/3 hp. DC.
EXAMPLE: How to order
(see model chart)
40 2 R6
1
2
3
1 Series Designation
2 Circuit
3 Float Arm and Flange Location
EXAMPLE: How to order
(see model chart)
41 2
1 2
1 Series Designator
2 Circuit
EXAMPLE: How to order
(see model chart)
49 4821 R6
1
2
3
1 Series Designator
2 Circuit
3 Float Arm and Flange Location
EXAMPLE: How to order
(see model chart)
46 2 R6
1
2
3
1 Series Designator
2 Circuit
3 Lever and Flange Location
EXAMPLE: How to order
(see model chart)
49 SRC 4820 R6
1
2
3
4
1 Series Designator
2 Spring Return
3 Circuit
4 Float Arm and Flange Location
EXAMPLE: How to order
(see model chart)
47 4821 R6
1
2
3
1 Series Designator
2 Circuit
3 Lever and Flange Location
Dwyer Instruments, Inc. P.O. Box 373/Michigan City, Indiana 46361/Phone 219 879-8000/Fax 219 872-9057 • U.K. Phone (+44) (0)1494-461707 • Australia Phone 61 2 4272-2055
129
Level
Consists of 4 ft. (1.22 M) stainless steel float rod, two 2 1/85 1/2
(54140 mm) cylindrical brass floats, and brass stops.
Consists of 4 ft. (1.22 M) stainless steel float rod, 4 1/2 (114 mm)
diameter 304SS float and stainless steel stops.
Consists of 4 ft. (1.22 M) stainless steel float rod, 4 1/2 (114 mm)
diametercopper float and brass stops.
Other rod lengths available. Consult factory.
37 - 49
CSA
PLUNGER TYPE FLOAT CONTROLS
Plunger type liquid level control with mercury switch and “snap action” movement assembly. For use with closed, ventilated tanks (cannot be used with
pressurized tanks). Maximum rod length 4 ft. (1.22 M). Operates with One 4 1/2 (114 mm) copper or stainless steel float or Two 2 1/85 1/2
(54140 mm) cylinder floats. (For liquids less than 0.90 specific gravity use three cylindrical floats). Furnished with 1/4 NPT bottom connection.
Mercury switch circuit. See Chart C.
Weather resistant NEMA - 3 case.
Float and Rod assemblies must be ordered separately. See Chart A. For minimum deadband see Chart B.
W
CSA
Similar to Type 49 except has spring return to hold lever arm in center (internal) position until the float engages upper or lower stop actuating
mercury switch. Circuit 4849 suitable for high and low alarm.
Mercury switch circuit. See Chart C.
Indicates lever is to the right and has bottom flange for mounting.
Other circuits available. Consult factory.
Float and Rod assemblies must be ordered separately. See Chart A. For minimum deadband see Chart B.
MODEL CHART – SERIES 41
2
CSA
R6
48xx
41
UL
R6
48xx
49SRC
49SRC
LEVER ARM OPERATED FLOAT CONTROLS
R6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement