Manual Index
DEMING ®
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Vertical Sump & Industrial Pumps
Series: 4560
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157 www.cranepumps.com
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 120015-Rev. E
CONTENTS
SAFETY FIRST ................................................................................3
Receiving, Storage, Service Centers
B. INSTALLATION ................................................................................4 - 5
C. ..................................................................................5
GENERAL REPAIRS
D. FOR INSPECTION AND REPAIR OF LIQUID END .........................5
E. FOR INSPECTION AND REPLACEMENT OF
F. TO REMOVE TOP COLUMN ADAPTER .........................................5 - 6
H. INSTALLING NEW BEARING BUSHINGS ......................................6
I. REASSEMBLY OF COLUMN PIPE ..................................................6
J. ASSEMBLY OF LIQUID END ...........................................................6
K. TO INSPECT OR REPLACE THRUST BEARING AND SEAL .........6 - 7
L. COLUMN PIPE DOWEL AND SHAFT
GUIDE BEARING ASSEMBLY .........................................................7 - 8
N. Fig. 4560 - 4570 ...............................................................................8
CROSS-SECTION & PARTS LIST ...................................................9 - 10
WARRANTY & RETURNED GOODS ..............................................11
Other brand and product names are trademarks or registered trademarks of their respective holders.
Deming® is a registered trademark of Crane Pumps & Systems, Inc.
2
SAFETY FIRST!
Please Read This Before Installing Or Operating Pump. This information is provided for SAFETY and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this information, observe the following symbols:
IMPORTANT! Warns about hazards that can result in personal injury orIndicates factors concerned with assembly, installation, operation, or maintenance which could result in damage to the machine or equipment if ignored.
CAUTION! Warns about hazards that can or will cause minor personal injury or property damage if ignored. Used with symbols below.
WARNING! Warns about hazards that can or will cause serious personal injury, death, or major property damage if ignored. Used with symbols below.
Hazardous fl uids can cause fi re or explosions, burnes or death could result.
Extremely hot - Severe burnes can occur on contact.
Biohazard can cause serious personal injury.
Hazardous fl uids can Hazardous pressure, eruptions or explosions could cause personal injury or property damage.
Rotating machinery
Amputation or severe laceration can result.
Hazardous voltage can shock, burn or cause death.
pump. Any wiring of pumps should be performed by a qualifi ed electrician.
WARNING ! To reduce risk of electrical shock, pumps and control panels must be properly grounded in accordance with the National Electric Code (NEC) or the Canadian
Electrical Code (CEC) and all applicable state, province, local codes and ordinances. Improper grounding voids warranty.
WARNING! To reduce risk of electrical shock, always disconnect the pump from the power source before handling or servicing. Lock out power and tag.
WARNING! Operation against a closed discharge valve will cause premature bearing and seal failure on any pump, and on end suction and self priming pump the heat build may cause the generation of steam with resulting dangerous pressures. It is recommended that a high case temperature switch or pressure relief valve be installed on the pump body.
CAUTION ! Never operate a pump with a plug-in type power cord without a ground fault circuit interrupter.
CAUTION ! Pumps build up heat and pressure during operation-allow time for pumps to cool before handling or servicing.
WARNING ! Do not pump hazardous materials
(fl ammable, caustic, etc.) unless the pump is specifi cally designed and designated to handle them.
CAUTION ! Do not block or restrict discharge hose, as discharge hose may whip under pressure.
WARNING ! Do not wear loose clothing that may become entangled in moving parts.
WARNING ! Keep clear of suction and discharge openings. DO NOT insert fi ngers in pump with power connected.
Always wear eye protection when working on pumps.
Make sure lifting handles are securely fastened each time before lifting. DO NOT operate pump without safety devices in place. Always replace safety devices that have been removed during service or repair. Secure the pump in its operating position so it can not tip over, fall or slide.
DO NOT exceed manufacturers recommendation for maximum performance, as this could cause the motor to overheat.
DO NOT remove cord and strain relief. DO NOT connect conduit to pump.
WARNING ! Cable should be protected at all times to avoid punctures, cut, bruises and abrasions. Inspect frequently. Never handle connected power cords with wet hands.
WARNING ! To reduce risk of electrical shock, all wiring and junction connections should be made per the NEC or CEC and applicable state or province and local codes. Requirements may vary depending on usage and location.
WARNING! Submersible Pumps are not approved for use in swimming pools, recreational water installations decorative fountains or any installation where human contact with the pumped fl uid is common.
WARNING! Products returned must be cleaned, sanitized, or decontaminated as necessary prior to shipment, to insure that employees will not be exposed to health hazards in handling said material. All Applicable
Laws And Regulations Shall Apply.
Bronze/brass and bronze/brass fi tted pumps may contain lead levels higher than considered safe for potable water systems. Lead is known to cause cancer and birth defects or other reproductive harm. Various government agencies have determined that leaded copper alloys should not be used in potable water applications. For non-leaded copper alloy materials of construction, please contact factory.
Crane Pumps & Systems, Inc. is not responsible for losses, injury, or death resulting from a failure to observe these safety precautions, misuse or abuse of pumps or equipment.
3
A - GENERAL INFORMATION
TO THE PURCHASER:
Congratulations! You are the owner of one of the fi nest pumps on the market today. These pumps are products engineered and manufactured of high quality components.
With years of pump building experience along with a continuing quality assurance program combine to produce a pump which will stand up to the toughest applications.
Check local codes and requirements before installation.
Servicing should be performed by knowledgeable pump service contractors or authorized service stations.
b.) Slide a locking collar onto the top end of the rod and push rod through fl oat switch arm. Guide the bottom end of the rod through the bottom guide bracket (527) on the pump casing (1) and lock a collar on the end of the rod by tightening the collar set screw.
c.) Lock the collar on the rod below the fl oat about
4” above the bottom guide bracket, then lock the collar above the fl oat at the desired starting (or stopping) level in the sump.
d.) After setting the pump in the pit, push the fl oat switch arm down to its lowest position. Lift the fl oat rod about 1/2” and fasten the top collar on rod with collar resting on switch arm. Lock the last collar 1/2” below the switch arm.
NOTE: See fl oat assembly on page 9.
This pump is designed for pumping raw or treated sewage, light sludge, slurries, industrial wastes and similar liquids containing solids. Standard pumps are assembled, adjusted and lubricated at the factory before shipment.
Motor and fl exible shaft coupling are normally shipped unmounted and are to be installed on the pump at job site.
2. Carefully lower the assembled unit into the pit. The support plate (23) should be approximately level and must rest evenly at all points before it is bolted to the
RECEIVING:
Upon receiving the pump, it should be inspected for damage or shortages. If damage has occurred, fi le a claim immediately with the company that delivered the pump.
If the manual is removed from the crating, do not lose or misplace.
STORAGE:
Short Term - Pumps are manufactured for effi cient performance following long inoperative periods in storage.
For best results, pumps can be retained in storage, as factory assembled, in a dry atmosphere with constant temperatures for up to six (6) months.
Long Term - Any length of time exceeding six (6) months, but not more than twenty four (24) months. The units should be stored in a temperature controlled area, a roofed over walled enclosure that provides protection from the elements (rain, snow, wind blown dust, etc..), and whose temperature can be maintained between +40 deg. F and
+120 deg. F. Pump should be stored in its original shipping container and before initial start up, rotate impeller by hand to assure seal and impeller rotate freely.
3. Turn pump shaft by hand to make sure that it rotates freely after installation - but before turning on the power. If there is a bind in the rotation, make 4 checks and possible adjustments as follows:
A. Adjust the position of the impeller by loosening the adjusting nut (66). Raise lock washer (69), then tighten adjusting nut to position the shaft and impeller above their lowest position by from 1/3 to
1/2 turn of the adjusting nut.
B. If “A” does not correct binding, loosen top lock nuts
(294) of both the discharge pipe and the grease pipe (if furnished) by two or three turns. Then gradually tighten discharge pipe top lock nut while checking shaft until the maximum shaft freedom of rotation is attained.
C. If “B” does not free shaft, raise the pump out of the pit and lower the bottom lock nuts of the discharge and lubrication pipes. Then reset the pump, bolting it to its foundation and continue to tighten the top lock nut of the discharge pipe up to 1 or 2 turns until freedom of rotation is attained.
D. Tighten the lubrication pipe top lock nut to just bear on the pump plate, raise the pump out of the sump, tighten the bottom lock nuts of the discharge and lubrication pipes and reset the pump.
E. Recheck the freedom of shaft rotation.
F. Disengage motor half coupling (42) from pump half coupling.
SERVICE CENTERS:
For the location of the nearest Deming Service Center, check your Deming representative or Crane Pumps &
Systems Service Department in Piqua, Ohio, telephone
(937) 778-8947 or Crane Pumps & Systems Canada, Inc.,
Bramton, Ontario, (905) 457-6223.
B - INSTALLATION
Standard pumps are completely assembled, carefully adjusted and lubricated at the factory before shipment.
4. Eliminate weight or strain of the piping connected to the pump before connecting this piping to the pump.
Recheck freedom of rotation (Section 3) after connecting system piping to pump discharge (295). A check valve and gate valve should be installed at the pump discharge to prevent back wash and pump back
spin.
assembled and partially adjusted before installing the pump. Insert the fl oat rod (529) through the guide on the support plate and slide a locking collar (530) on the bottom of the rod, then the fl oat (532) and another locking collar (530).
5. Be certain to connect power lines to motor leads as shown on motor wiring diagram for the line voltage
4
6. Be sure starter or fl oat switch overload protection device is proper for the voltage used and the motor
horsepower.
2. Unscrew the top pipe nut (294) and loosen the bottom pipe nut (294). The discharge pipe (161) can now be removed from the pump either by unscrewing the pipe or removing bolts and nuts at the pipe fl ange.
7. Start motor, and test for proper rotation. The shaft should rotate clockwise when looking down on the motor. (For left hand pumps the shaft should rotate counter-clockwise.) If rotation is wrong, reverse any two line leads to the motor if 3 phase power is used.
If single phase is used, consult motor manufacturer or his representative. After correct rotation is obtained, connect the drive coupling. (If the pump shaft should be rotated in the wrong direction, the shaft couplings might unscrew and cause a bent shaft or broken impeller or casing.)
3. Next, unscrew the nuts (361) holding the strainer
(316) to the pump casing (1). (Note: Pump sizes
3MD, 4MD, 5MD, 5MSD and 6MD have two-piece strainers.) Remove nuts (226). Casing can now be removed from casing adapter (71). Place casing gasket (73) in a bucket of water to keep it pliable.
4. Unscrew the impeller nut (26) by turning it counter-clockwise while holding the drive coupling
(42) with a strap wrench.
8. Before starting pump close gate valve. Start pump and slowly open gate valve until desired capacity is
obtained.
9. Pump should operate smoothly, If pump vibrates, there may be a severe distortion of the pump as a result of excessive installation strains on pump support plate or discharge pipe, or because of damage in shipment.
5. Remove the impeller (2) from the shaft (6), use a pry between impeller shroud and casing adapter
(71). Remove impeller washer (270). Lift impeller key
(32) from shaft.
E - FOR INSPECTION AND
REPLACEMENT OF BEARING
BUSHINGS
1. Dismantle liquid end as described in Section B.
C - LUBRICATION
1. Pump bearings are properly fi lled with grease at the factory before shipment. Periods of subsequent lubrication depend somewhat on local conditions, hours of operation, load, speed, temperature, etc.
As a guide we recommend that the thrust bearing (18) be greased every two or three months and, for grease lubricated pumps, the shaft bearing bushings (39) every eight hours of operation. If liquid being pumped contains abrasives, lubricate shaft bearings (39) every four to six hours of operation.
2. Disconnect grease pipes (335) starting at the pump support plate (23).
3. Unscrew nuts (226) holding the casing adapter (71) and bottom bearing housing (307) to the bottom column pipe (101). The casing and bottom bearing housing can now be removed from the column pipe.
2. A lithium base grease #2 or #3 consistency should be used for thrust bearing (18) and a water resistant grease such as “Lubri-plate 142” for the shaft bearing
4. If it is necessary to replace the choker ring (257) and bottom bearing bushings (39), carefully note their position in the bearing housing, then, with a piece of tubing or round bar of the proper size, push the bearing bushing and choker ring out of the fl anged end of the housing.
3. Motor bearings normally require a lithium base grease #2 or #3 consistency. Follow motor manufacturer’s recommendation as to grease and frequency of lubrication.
GENERAL REPAIRS
D - FOR INSPECTION AND REPAIR
OF LIQUID END
1. Close discharge gate valve and disconnect pipe at pump support plate, also remove electric wires from the motor. Unscrew foundation bolts in the support plate (23) then lift pump and support plate as a unit from the pit to the fl oor.
5. To remove the intermediate bearing housing (307) and bearing bushings (39), unscrew fl ange bolts (285) and nuts (256) and slide bottom column pipe (101) off over shaft (6) then slide bearing housing (307) with bearing bushings (39) off the shaft. Note position of bearing bushings in housing then push the bearing bushings out of the housing as described in #4 above.
F - TO REMOVE TOP COLUMN
ADAPTER
If pump liquid end and column pipe has been dismantled as described in Section B and C, then proceed as follows:
Unscrew top column bolts (260) and nuts (256) and slide top column pipe (101A) off the shaft, then, top column adapter (199).
5
Note: If pump motor end has been dismantled as described in Section K, then proceed as follows:
Remove bolts (277) and nuts (258) holding motor support
(19) to support plate (23), then, remove bolts (260) and nuts (256). Lift present top column adapter (199) from top column pipe fl ange and install new adapter in the top pipe fl ange. Reposition motor support on support plate and replace bolts (260) and nuts (256) and bolts (277) and nuts (258). Complete assembly as described in
Section K.
J - ASSEMBLY OF LIQUID END
1. Position casing adapter (71) against bottom bearing replace nuts (226). Tighten securely.
G - REPLACING TOP COLUMN
ADAPTER
1. Slide top column adapter (199) over the shaft, then the top column pipe (101A). Line up the holes in the top column pipe fl ange and top column adapter fl ange with those in the bottom of the motor support
(19) and replace bolts and nuts (260). Tighten
securely. sure the hole for grease pipe (335) is in
3. Next, place bottom bearing housing (307) over the end of the shaft and slide against fl ange of bottom column pipe (101). Align bolt holes with those of
2. Replace key (32) in shaft and place impeller (2) on the shaft with keyway over the key. Place a wood block over impeller vanes and tap on wood to seat impeller on shaft. Replace impeller washer (270) on the shaft, then the impeller screw (26). Tighten
DO NOT USE IMPELLER SCREW TO DRAW
IMPELLER ONTO SHAFT. SCREW IS A
LOCKING DEVICE ONLY!
3. Position casing gasket (73) on casing (1) and mount casing on casing adapter (71), then tighten nuts (226). Replace strainer (316) on studs (360), replace nuts (361) and tighten.
H - INSTALLING NEW BEARING
BUSHINGS
1. Bearing bushings (39) are furnished in sections, two sections required per housing. Place the intermediate bearing housing (308) in a vise, fl anged end up.
Select a bearing bushing (39) and note that one end shows a grease groove while the other end is plain (except for graphitor and rubber bearings).
4. Reassemble grease pipes (335) and force fresh grease into the bearing busings (39). Also assemble the discharge pipe (161) and tighten nuts (294), tightening the one below the support plate fi rst. Be careful that a strain is not placed on the pump shaft due to improper adjustment of the grease pipe and discharge pipe lock nuts (294).
2. Position bearing bushing (39) in the cavity of the intermediate bearing housing (307) with grease groove down, and carefully press bearing into position as shown. Also press choker ring (257) into position, (on bottom bearing housing only). Turn the intermediate bearing housing over and carefully press other half of bearing bushing into position in the same manner.
DO NOT COVER GREASE PORT IN SIDE OF
BEARING HOUSING.
Note: Other design construction will require same modifi cation of above depending upon the particular construction.
5. Turn pump shaft (6) by hand several times to make sure that shaft turns freely. Then follow installation
instructions.
K - TO INSPECT OR REPLACE
THRUST BEARING AND SEAL
1. Disconnect power lines from the motor, then remove motor cap screws (219) and lift motor and motor half of coupling (42) from the motor support (19).
Remove the coupling spider and lower half of coupling (42) from the pump shaft (6). Shaft key (46) will come off at this time.
I - REASSEMBLY OF COLUMN PIPE
1. Slide the intermediate bearing housing (307) over the shaft and push against fl ange of the top column pipe (101A). Turn bearing housing so that grease port in housing lines up with hole in column pipe.
Place bolts (285) through holes in fl ange.
2. Remove adjusting nut (66), then, remove lock washer (69) and unscrew the adjusting nut (66 from the shaft by turning it counter-clockwise.
Remove bearing housing bolts and nuts (332) and grease cup (242). Lift the entire assembly consisting of the bearing adapter (170), gib key (244), bearing housing (33), perfect seal (169A), thrust bearing
(18), and the shaft perfect seal (169) from the motor
2. Slide bottom column pipe (101) onto shaft with grease hole in line with hole in the top column pipe
Replace nuts (256) and tighten securely. Be sure the hole for grease pipe is in proper position.
6
3. To remove bearing adapter (170), thrust bearing (18), and felt seal (169A) from the bearing housing (33), place a rod through the hole at the shaft sirvene seal (169) and bump gently on the bottom of the bearing adapter (170) moving around its diameter until it is released from the housing. This should be design of guide bearings and lubrication modifi ed for the particular application concerned. The different designs and their application are as follows:
4. To remove the thrust bearing (18) from the bearing adapter (170). The felt seal (169A) can also be pulled from the adapter. The shaft seal (169) should be pushed out of the bearing housing (33) with a rod or piece of wood. Note: When installing a new thrust bearing, we also recommend replacing the two seals
(169A) and (169).
5. Press new felt seal (169A) onto bearing adapter (170).
Next, press the thrust bearing (18) onto the bearing adapter with the wide space between the bearing races toward the top of the adapter, then replace snap ring. The sirvene seal (169) should be pressed into the bearing housing (33) with the “lip” visible, looking down into the housing. Apply fresh grease to thrust bearing and loosely pack the bearing housing with
grease.
FOR STANDARD DRAINAGE SERVICE -
NONCORROSIVE LIQUIDS WITHOUT ABRASIVES
OR VAPORS
6. Place bearing housing (33) in a vise with fl ange resting on vise jaws. Place bearing adapter assembly over bearing housing (33) and press down on top of adapter to seat thrust bearing (18) in its seat. Lay a piece of wood across the top of the bearing adapter and tap wood to completely seat bearing and perfect
seal.
7. Guide the bearing housing and bearing adapter assembly over the shaft. Line up the bolt holes with those in motor support (19) and replace bolts and nuts
(332), grease cup (242), and gib key (244). Screw the adjusting nut (66) onto the pump shaft and tighten until shaft just turns free by hand. Turn the adjusting nut (66) two additional fl ats of the hex nut and replace lock washer (69). Tighten second adjusting nut
(66) against lock washer (69).
DESIGN 1 - TOP
Design 1 is the standard cast iron column top closure.
DESIGN 8 - INTERMEDIATE
Design 8 is the standard intermediate shaft guide bearing
8. Turn shaft several times by hand to be certain that it turns freely and doesn’t bind. Replace the bottom half of coupling (42) and shaft key (46) on the shaft
(6). Replace the motor on the motor support (19) engaging the upper and lower halves of coupling (42).
Replace cap screws (219) holding motor.
L - COLUMN PIPE DOWEL AND SHAFT
BEARING
The pump construction as shown in cross section on page
9 is a standard for a grease lubricated pump of suffi cient length to require an intermediate guide bearing. Pumps specifi cally designed for handling corrosive, abrasive, or odorous liquids will have materials of construction, assembly with cast iron bushings and grease lubrication.
(Use with settings of over 6 feet).
DESIGN 6 - BOTTOM
Design 6 is the standard bottom shaft bearing assembly.
7
The choker ring resists lubricant fl ushing by the liquid c. Impeller diameter too small d. Wrong direction of rotation
4. Pump takes too much power a. Speed too high for required head and capacity b. Head lower than rating; pumps to much water c. Liquid either viscous or heaver than water or both
1. Shaft bent
2. Impeller binds in casing e. Strain on pump caused by piping misalignment f. Liquid pumped leaves a deposite between the shaft and the bearings or between the impeller and the
casing.
g. Wrong electrical connections pumped.
FOR SPECIAL PUMPING SERVICES
DESIGN 1A -TOP
For Noncorrosive Vapors which can be contained by
N - Fig. 4560 - 4570
Pump standard sectional assembly and standard parts list apply to pumps of standard construction. Deviations from this construction may result from the use of alternate shaft guide bearing construction or methods of lubrication as described on pages 7 thru 8.
Intermediate guide bearings (33) usually are used only if column length exceeds 5 feet.
grease-lubricated Top Column Closure. Use instead of
Design 1.
DESIGN 3 - TOP
Design 3 For Hot or Corrosive Vapors which can be contained by a stuffi ng box. Use instead of Design 1.
Design 3 also can be fi tted with inlet and outlet connections for pressurizing inside of the column with water, air or steam to keep abrasive or corrosive liquids out of the bearing assemblies.
Shaft (6) is furnished in two or more lengths coupled together if column length plus liquid end exceeds 10 feet.
Discharge pipe coupling (295) is replaced by a fl at faced
ASA fl ange on pipe sizes 3” and larger.
Chair bracket mounted units must be realigned every other day during the fi rst week of operation, then once each week until alignment remains constant.
M - LOCATING TROUBLE
1. No water delivered a. Wrong direction of rotation b. Strainer, impeller or pipes plugged c. Discharge head too high d. No water in pit
2. Not enough water delivered a. Strainer, impeller or pipes partly plugged b. Discharge head higher than expected c. Improper impeller adjustment d. Low water level in pit
1. Impeller worn or damaged
2. Casing worn f. Wrong direction of rotation
3. Not enough pressure a. Air in water
8
9
Description
Casing
Impeller
Shaft
Ball Bearing
Frame
Split Cover Plate
Impeller Screw
Impeller Key
Bearing Housing
Bearing Bushing
Coupling Half - Driver
Coupling Half - Pump
Coupling Key
Coupling Spider
Shaft Adjusting Nut
Lock Washer
Shaft Coupling
Casing Adapter
Gasket
Column Pipe
Column Pipe - Top
Discharge Elbow
Discharge Pipe
Lower Seal
Seal-Top
Bearing Adapter
Top Closure
Cap Screw
Pipe Plug
Cap Screw
Cap Screw
Gasket
Grease Fitting
Bearing Adapter Key
Frame Gasket
Pipe Nut Gasket
Washer
Hex Nut
Choker Ring
Hex Nut
Cap Screw
Cap Screw
Cap Screw
Hex Nut
Impeller Washer
Item No.
169A
170
199
212
216
219
226
* 241
70
71
* 73
101
101A
105
161
169
33
* 39
42
44
46
48
66
69
6
* 18
1
2
19
23
* 26
32
242
244
250
254
255
256
* 257
258
260
265
267
268
270
Item No.
335
336
341
360
361
520
527
529
277
285
289
294
295
307
316
332
530
532
543
546
547
548
549
557
559
Description
Cap Screw
Cap Screw
Hex Nut
Pipe Nut
Dishcharge Flange
Bearing Retainer
Strainer
Cap Screw
Lube Pipe Assembly
Gasket
Hex Nut
Stud
Hex Nut
Set Screw
Float Rod Bottom Guide
Float Rod
Float Rod Collars
Float
Cover Plate
Bellows
Machine Screw
Washer
Float Rod Guide Tube
Float Guide
Guide Pipe
10
Limited 24 Month Warranty
Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law
(1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, his successor, or assigns, notifi es us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply.
THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY
PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR
AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE
NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly stated otherwise, guarantees in the nature of performance specifi cations furnished in addition to the foregoing material and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for fi eld performance. Any additional guarantees, in the nature of performance specifi cations must be in writing and such writing must be signed by our authorized representative. Due to inaccuracies in fi eld testing if a confl ict arises between the results of fi eld testing conducted by or for user, and laboratory tests corrected for fi eld performance, the latter shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS
ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND
PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF
SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.
This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning
(d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any modifi cation of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice and\or our specifi c recommendations. The purchaser is responsible for communication of all necessary information regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR
ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES,
RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST
PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES
ARE CAUSED BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN
SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157 www.cranepumps.com
83 West Drive, Brampton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
IMPORTANT!
WARRANTY REGISTRATION
Your product is covered by the enclosed Warranty.
To complete the Warranty Registration Form go to: http://www.cranepumps.com/ProductRegistration/
If you have a claim under the provision of the warranty, contact your local
Crane Pumps & Systems, Inc. Distributor.
RETURNED GOODS
RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.
Products Returned Must Be Cleaned, Sanitized,
Or Decontaminated As Necessary Prior To Shipment,
To Insure That Employees Will Not Be Exposed To Health
Hazards In Handling Said Material. All Applicable Laws
Regulations Apply.
