Aigis Mechtronics MT9207 7-inch Column Mount, MT9214 14-inch Column Mount, MT9224 24-inch Column Mount, MT9216 16-inch Wall Mount, MT9222 22-inch Wall Mount, MT9227 Adjustable Head Bracket, MT9226 Corner Bracket Installation and Operating Instructions

51 x4
2.0
I NDOOR /O UTDOOR
H EAVY-D UTY M OUNTS
13
0.5
Mi
3
1.
6xø
ø
76
3.00
152
6.0
32
1.25
6 x ø 13
0.50
ø
MT9207, MT9214, MT9216,
MT9222, MT9224, MT9226
MT9227, MT9228, MT9234,
MT9235, MT9237
32
1.25
76 210
3.00 8.25
152
6.00
7
2.
I N S TA L L AT I O N
O P E R AT I N G I N S T R U C T I O N S
W W W. A I G I S M E C H . C O M
AND
4.1 MT9207 178-mm (7-inch),
MT9214 356-mm (14-inch) and
MT9224 610-mm (24-inch)
Column Mounts
SAFETY PRECAUTIONS
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Side View
SECURITE
Le point d'exclamation à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'instructions importantes d'utilisation et de maintenance dans la documentation accompagnant l'appareil.
Top
1.
SICHERHEITSVORKENHRUNGEN
Das Ausrufezeichen in dem gleichseitigen Dreieck ist
dazu da, den Benutzer auf wich-tige Inbetriebnahmeund Instandhaltungs-vorschriften hinzuweisen, die
dem Gerät in Form einer Broschüre beigelegt sind.
2.
PRECAUCIONES DE SEGURIDAD
El símbolo de exclamación dentro de un triángulo
equilátero, se muestra con el objetivo de alertar al
ususario de que instrucciones de operación y mantenimiento importantes acompañan al equipo.
1
UNPACKING
Unpack carefully.This is mechanical equipment and should be
handled carefully.
Check for the following items:
• Verify the unit model number.
• Installation and Operating Instructions.
If an item appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper. If any items are
missing, notify Aigis Mechtronics.
The shipping carton is the safest container in which the unit
may be transported. Save it for possible future use.
2
SERVICE
3
DESCRIPTION
4
INSTALLATION
3.
4.
5.
If the unit ever needs repair service, the customer should
contact Aigis Mechtronics.
6.
These versatile indoor/outdoor mounts accommodate fixed
cameras, housings, pan/tilts, and scanners.
See SPECIFICATIONS for the maximum rated load of
mount.
Mounting Hardware: Not furnished.
Note:The use of stainless steel or zinc-plated fasteners is
recommended.
2
Determine a secure mounting location, either for a
pedestal (floor) mounted installation or for an overhead
(ceiling) mounted installation.
Caution:
a. For a secure mounting installation, bolts should
extend through the mounting surface and be secured
with nuts, washers, and lock washers on the opposite
side.
b. If studs are used, they should either be anchored in
concrete or welded to a steel backer plate.
c. If the MT9207, MT9214 or MT9224 is mounted to
wood or a blind structure (with no access to the
rear) in a ceiling, make certain that the mounting fasteners have a minimum pull-out strength of 600
pounds.
WARNING:The maximum rated load is reduced to 45.3
kg (100 lb) when mounted beneath a ceiling.
Locate and drill four mounting holes using the end flanges
as a template.
Using four bolts (or studs) with nuts, washers, and lock
washers, fasten the MT9207,MT9214 or MT9224 to its
mounting location and tighten all nuts securely.
Note:The minimum diameter bolt (or stud) required is
10 mm (3/8 in).
To mount the MT9227 Adjustable Head Bracket:
a. Use the mounting hole which is located in the center
of the MT9207, MT9214 or MT9224 mounting plate.
This mounting hole is threaded to receive a 1/4-20
bolt.
b. Insert a 1/4-20 hex head machine bolt with washer
and lock washer through the MT9227 base plate and
into the threaded insert on either end flange of the
MT9207, MT9214 or MT9224.
To mount the MT9237 Heavy Duty Adjustable Head
Bracket:
a. Line up the holes in the corners of the MT9237 base
plate with the slots in the mounting flange.
b. Insert a 3/8-16 x 1” hex bolt through the base plate
and mounting flange, using a 3/8” flat washer and a
3/8” spiral lock washer under the head of the bolt.
c. From the underside of the mounting flange, use a
3/8” flat washer and a 3/8-16 hex nut to secure the
MT9237 to the mounting flange.
d.
7.
Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
To mount a pan/tilt or scanner device:
a. The slotted mounting holes on the MT9207, MT9214
or MT9224 can accommodate the following mounting hole dimensions of pan/tilts and scanners:
Max.
Min.
Bolt Circle
197 mm (7.75 in) 121 mm (4.75 in)
Square Centers 140 mm (5.50 in) 85 mm (3.36 in)
b. To install, line up the holes in the base mounting
plate of the device. Insert a minimum of four
machine bolts (not included) with flat washers
through the device and the end flange of the
MT9207, MT9214 or MT9224; then securely fasten
using lock washers and nuts.
6.
4.2 MT9216 409-mm (16-inch) and
MT9222 564-mm (22-inch)
Wall Mounts
Back
1.
2.
3.
4.
5.
7.
Side View
Determine a secure wall mounting location.
WARNING: Do not mount in an inverted
position.
Caution:
a. For a secure installation use six (6) bolts (not
included). The bolts should extend through the
mounting surface and be secured with nuts, lock
washers, and flat washers on the opposite side.
b. If studs are used, they should be anchored in
concrete or welded to a steel backer plate.
c. If the wall mount is attached to wood or to a blind
structure (with no access to the rear), make certain
that the mounting fasteners have a minimum pullout strength of 600 pounds.
8.
For ease of installation, locate the bottom mounting holes
first. Install the bolts (or studs) into the wall surface.
WARNING:The MT9216 and MT9222 must
be mounted with the slotted mounting holes of
the wall plate at the bottom.
Reseat the MT9216 or MT9222 on the bolts (or studs)
using the bottom slotted holes, then locate the upper
mounting holes and drill into the wall surface.
Install the upper bolts (or studs) through the wall mount
and into the wall surface. Tighten upper and lower bolts
(or studs) securely.
Note:The minimum diameter bolt (or stud) required is
10 mm (3/8 in).
3
To mount the MT9227 Adjustable Head Bracket to:
MT9216 Wall Mount
a. Use the 1/4-20 threaded mounting hole located in
the center of the slot pattern.
b. Insert a 1/4-20 hex head machine bolt, washer, and
lock washer through the adjustable head and into the
threaded insert in the wall mount. The bolt should
be 20 mm (3/4 in) long. A lock washer and a flat
washer must be used under the head of the bolt.
MT9222 Wall Mount
a. Line up the hole in the MT9227 base plate with the
center mounting hole on the mounting bracket.
b. Insert a bolt with flat washer through the MT9227
base plate and mounting bracket. A
5/16-18 x 50 mm (2-in) long bolt (not supplied) is
recommended to fasten the MT9227 to the mounting bracket.
c. From the underside of the mounting bracket, use a
lock washer and nut to secure the MT9227.
Temporarily leave hand tight.
To mount the MT9237 Heavy Duty Adjustable Head
Bracket to the MT9216 or the MT9222 Wall Mounts:
a. Line up the holes in the corners of the MT9237 base
plate with the slots in the flange bracket.
b. Insert a 3/8-16 x1” hex bolt through the base plate
and flange bracket, using a flat washer and a 3/8” flat
washer and 3/8” sprial lock washer under the head
of the bolt.
c. From the underside of the flange bracket, use a 3/8”
flat washer and 3/8-16 hex nut to secure the
MT9237 to the mounting flange.
d. Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
To mount a pan/tilt or scanner device:
a. The slotted mounting holes on the MT9216 and
MT9222 can accommodate the following mounting
hole dimensions of pan/tilts and scanners:
Max.
Min.
Bolt Circle
197 mm (7.75 in) 121 mm (4.75 in)
Square Centers 140 mm (5.50 in) 85 mm (3.36 in)
b. To install, line up the holes in the base mounting
plate of the device. Insert a minimum of four
machine bolts (not included) with flat washers and
lock washers through the device and the mounting
plate of the wall mount; then securely fasten using
lock washers and nuts.
4.3 MT9227 Adjustable Head Bracket
Top View
(Mounting Plate)
Side View
Bottom View
(Base Plate)
3.
Tilt
Adjust
4.
4.3.1Parts List
Mounting Plate 2 - Flat Washers
Base Plate
2 - Neoprene Washers
2 - 1/4-20 Hex Bolts
Mounting
Plate
MT9214 ColumnMount
Insert a 1/4-20 hex head machine bolt through the
MT9227 base plate and into the threaded insert on
either end flange of the MT9214.
To install a camera or camera/housing assembly:
a. Insert two (2) 1/4-20 bolts with flat washers from
the underside of the MT9227 mounting plate.
b. Thread into the underside of the camera or housing
and tighten securely.
To adjust the MT9227:
a. Observe the camera video on a monitor while moving the camera to the desired position.
b. Tighten securely both the base plate mounting bolt
and the two side bolts.
4.4 MT9237 Heavy Duty Adjustable Head
Bracket
Flatwasher
Top View (Mounting Plate)
Bottom View (Base Plate)
Side View
Neoprene
Washer
1/4"-20
Hex Bolt
4.4.1 Parts List
8 - 3/8” Flat Washers
4 - 3/8” Split Lock Washers
4 - 3/8 x 16 x 1” Hex Bolt
4 - 3/8 x 16 Hex Nut
Base
Plate
4.3.2 Assembly
1.
2.
3.
Insert a neoprene washer between each side of the
mounting plate and base plate.
Line up each of the side holes; insert one 1/4-20 hex
head machine bolt with flat washer and screw into each
threaded hole in base plate.
Hand tighten side bolts until ready to install.
Top
4.3.3 Installation
1.
2.
The MT9227 is intended for installation on a rigid mounting surface by use of a bolt through the base plate.
To mount the MT9227 Adjustable Head Bracket to:
MT9216 Wall Mount
a. Use the 1/4-20 threaded mounting hole located in
the center of the slot pattern.
b. Insert a 1/4-20 hex head machine bolt through the
adjustable head and into the threaded insert in the
wall mount. The bolt should be 20 mm (3/4 in) long.
A lock washer and a flat washer must be used under
the head of the bolt.
MT9222 Wall Mount
a. Line up the hole in the MT9227 base plate with the
center mounting hole on the mounting bracket.
b. Insert a bolt with flat washer through the MT9227
base plate and mounting bracket. A 5/16-18 x 50
mm (2 in) long bolt (not supplied) is recommended
to fasten the MT9227 to the mounting bracket.
c. From the underside of the mounting bracket, use a
lock washer and nut to secure the MT9227. Leave
hand tight.
Base (Bottom)
4.4.2 Installation
1.
2.
4
The MT9237 is intended for installation on a rigid
mounting surface by use of 4 x 3/8-16 x1” Hex Bolts
through the corners of the base plate.
To mount the MT9237 Heavy Duty Adjustable Head
Bracket to: MT9207, MT9214 and MT9224 Column
Mounts or the MT9216 and MT9222 Wall Mounts:
a. Line up the holes in the corners of the MT9237 base
plate with the slots in the mounting flange.
b. Insert a 3/8-16 x 1” hex bolt through the base plate
and mounting flange, using a 3/8” flat washer and a
3/8” spiral lock washer under the head of the bolt.
c. From the underside of the mounting flange, use a
3/8” flat washer and a 3/8-16 hex nut to secure the
MT9237 to the mounting flange.
d. Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
Note: Do not mount the MT9216 or the MT9222 in an
inverted position.
1.
4.5 MT9228 Flange Bracket
4.5.1Parts List
2.
Mounting Plate
5 - 3/8 Flat Washers
5 - 3/8-16 Lock Nuts
6 x Customer Supplied Bolt
MT9216 or
MT9222
Wall Mount
5 x Threaded Pemstud
(Pre-Assembled)
5 x 3/8 Plain Washer
5 x 3/8-16 Lock Nut
MT9228
Flange Bracket
3.
Note:The MT9228 flange bracket is used to increase the
weight distribution on insufficient load bearing surfaces for
the MT9216 and MT9222 wall mounts.
4.
5.
4.5.2 Installation
1.
2.
3.
4.
5.
Determine a secure wall mounting location.
Mount the MT9228 flange bracket with the preassembled threaded pemstuds facing outward from the
mounting surface.
Determine a secure wall mounting location.
Caution:
a. Use 10 mm (3/8 inch) stainless steel or zinc plated
fasteners (not included) for secure installation.
b. If bolts are used, they should extend through the
mounting surface and be secured with flat washers,
lock washers, and nuts on the opposite side. Each
bolt must have a minimum pull-out strength of 780
N (175 lb).
c. If studs are used, they should be anchored in
concrete or welded to a steel backer plate. Each
stud must have a minimum pull-out strength of 780
N (175 lb).
d. If the wall mount is attached to wood or a blind
structure (with no access to the rear), make certain
that the mounting fasteners have a minimum pullout strength of 780 N (175 lb).
Locate the eight holes or stud locations using the bracket
as a template (four holes per bracket leg).
Install the mount using at least eight bolts or studs.
Mount wall or dome mount as instructed in the
accompanying instructions.
4.7 MT9234 16-inch Wall Mount with
Adjustable Head Bracket
The MT9234 unit is a combination of the MT9216 Wall
Mount and the MT9227 Adjustable Head Bracket. Refer to
Section 4.3.3, item 2 for assembly instructions.
Caution:
a. For a secure installation, use six (6) bolts (not
included). The bolts should extend through the
mounting surface and be secured with nuts, lock
washers, and flat washers on the opposite side.
b. If studs are used, they should be anchored in
concrete or welded to a steel backer plate.
c. If the flange bracket is attached to wood or to a
blind structure (with no access to the rear), make
certain that the mounting fasteners have a minimum
pull-out strength of 600 pounds.
Mount either the MT9216 or the MT9222 wall mounts
to the MT9228 flange bracket. Align the mounting holes
of the wall mount with the five (5) threaded pemstuds of
the flange bracket.
Follow instructions, MT9216 409-mm (16-inch) and
MT9222 564-mm (22-inch) Wall Mounts, for wall
mount installation to the MT9228 flange bracket.
4.8 MT9235 22-inch Wall Mount with Heavy
Duty Adjustable Head Bracket
The MT9235 unit is a combination of the MT9222 Wall
Mount and the MT9237 Heavy Duty Adjustable Head Bracket.
Refer to Section 4.2, item 7 for assembly instructions.
4.6 MT9226 Corner Bracket
Top View
Mounting
Surface
5
5
SPECIFICATIONS
Top and Bottom
View of
Mounting Flanges
5.1 Column Mounts
MT9207 178-mm (7-inch)
MT9214 356-mm (14-inch)
MT9224 610-mm (24-inch)
Bolt Circle View
Same as Wall Mount
178
7.0
1/4-20
Top and Bottom
Maximum Rated Load:
Upright: 90.6 kg (200 lb).
Inverted: 45.3 kg (100 lb).
Mounting Hardware: Not furnished.
Finish: Light Gray Powder Coat
Weight:
MT9207 : 1.6Kg (3.5 lb)
MT9214: 2.3 kg (5.1 lb).
MT9224: 3.3 kg (7.2 lb).
178
7.0
Side View
76
Dia..
3.0
610
24.0
MT9207 - 7"
mm
in
Bolt Circle View Same
As Wall Mounts
Top and Bottom
View of Mounting
Flanges
MT9224
7.0
178
1/4-20
Top and Bottom
5.2 MT9216 409-mm (16-inch) and
MT9222 564-mm (22-inch)
Wall Mounts
7.0
178
Side
View
3.0
76
Maximum Rated Load:
MT9216: 45.3 kg (100 lb).
MT9222: 90.6 kg (200 lb).
Mounting Hardware: Not furnished.
Finish: Light Gray Powder Coat
Weight:
MT9216: 1.6 kg (3.5 lb).
MT9222: 2.9 kg (6.5 lb).
Note: Do not mount the MT9216 or MT9222 wall mounts in
an inverted position.
7.0
178
in
mm
MT9207
Bolt Circle View S ame
As Wall Mounts
Top and Bottom
View of Mounting
Fla ng es
1/4-20
Top a nd Bottom
S ide
View
See Detail B
41
178
7.0
See Detail A
for Top View of
Mounting Pattern.
1.6
178
7.0
190
7.5
76 Dia.
3.0
356
14.0
178
mm
in
mm
in
410
16.1
7.0
MT9216
MT9214
6
41
1.6
See Detail B
5.3 MT9227 Adjustable Head Bracket
See Detail A
for Top View of
Mounting Pattern.
Maximum Rated Load: 45.3 kg (100 lb).
Mounting Hardware: Not furnished.
Finish: Light Gray Powder Coat
Weight: 0.55 kg (1.2 lb).
190
7.5
76
3.0
Top View
(Mounting Plate)
mm
in
178
24
x2
1.0
564
22.2
7.0
63
2.5
127
5.0
MT9222
51 x4
2.0
Side View
7.1
Dia.
0.28
11.9 L
2 Slots x
0.47
152
6.0
1 Hole
13
0.5 x4
1/4-20
85 Min.
3.36
mm
in
D
140
5.50 Max.
Bolt Squares
114
4.5
Tilt
Adjust
Mounting
Bolt Circles
197 Max.
7.75
121 Min.
4.75
76
3.0
Bottom View
(Base Plate)
mm
in
Detail A - MT9216 and MT9222
15.2
6.0
1.3
8.6 Dia. (Ctrd)
0.34
MT9227
5.4 MT9237 Heavy Duty Adjustable Head
Bracket
Maximum Rated Load: 90.72kg (200 lb)
Mounting Hardware: Included (see hardware kit contents)
Finish: Light Gray Powder Coat
Weight: 1.09 kg (2.4 lb)
Horizontal Rotation (Pan): 180º
Vertical Rotation (Tilt): 180º
1.3
0.5
7.6
3.0
114
4.5
Dia.
0.5
(3 Places)
16.5
6.5
mm
in
Side View
1.3
0.5
139.7
5.50
100
3.94
Detail B - MT9216
Tilt Adjust
Top View
(Mounting Plate)
180.3
7.10
ø7.14
ø.281
49.3
1.94
145.3
5.72
Bottom View
(Base Plate)
mm
in
7
12.2
.48
ø 13.5
ø .53
139.7
5.50
139.7
5.50
MT9237
5.5 MT9226 Corner Bracket
5.6 MT9228 Flange Bracket
Maximum Rated Load: 45.3 kg (200 lb).
Mounting Hardware: Not furnished.
Finish: Light Gray Powder Coat
Weight: 2.9 kg (6.5 lb).
32
1.25
6 x ø 13
0.50
ø
Maximum Rated Load: 45.3 kg (200 lb).
Mounting Hardware: (5) 3/8-16 x 1 1/4 studs, (5) 3/8 flat
washers, and (5) 3/8-16 lock nuts.
Finish: Light Gray Powder Coat
Weight: 2.1 kg (4.6 lb).
ø 5 x 3/8-16 Studs
32
1.25
157
6.20
101.6
76.2
4.00
3.00
76 210
3.00 8.25
152
6.00
76.2
3.00
74
2.90
165
254 6.50
10.00
6
0.25
67
2.64
8 x ø 14
0.54
mm
in
25.4
1.00
mm
in
ø 6 x12.7
0.50
482.6
19
452.9
17.83
165.1
6.50
101.6
4.00
25.4
63.5 1.00
2.50
MT9228
229
9.00
MT9226
©2010 Aigis Mechtronics
1124 Louise Road,Winston-Salem, NC 27107-5450
Tel: 336.785.7740 Fax: 336.785.7744
Data subject to change without notice
100 0045 003 AIG 04/10
Printed in U.S.A.