Metra Electronics 99-4012 Radio Installation Kit Installation Instructions

Metra Electronics 99-4012 Radio Installation Kit Installation Instructions

Below you will find brief information for Radio Installation Kit 99-4012. This kit allows you to install aftermarket radios into a wide range of General Motors vehicles from 1982 to 2002. It includes a Radio Housing, 1" Faceplate, ½" Faceplate, Flat Faceplate, Keps Nuts, Hex-head Screws, Carriage Bolts, and Rear Support Bullet. The kit can be used with both 2-shaft and DIN head units. It also includes instructions on how to connect the wiring harness.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Radio Installation Kit 99-4012 Installation Instructions | Manualzz
KIT COMPONENTS
Radio Housing
99-4012
1" Faceplate
½" Faceplate
Flat Faceplate
INSTALLATION
INSTRUCTIONS
APPLICATIONS
GENERAL MOTORS 1982-02
VEHICLES EQUIPPED WITH J-2000 PANEL-STYLE
FACTORY HEAD UNIT PROVISIONS
(SEE INSIDE FOR SPECIFIC APPLICATIONS)
(6) Keps Nuts
(6) Hex-head
Screws
(6) Carriage Bolts
Rear Support Bullet
TOOLS REQUIRED
Phillips screwdriver
1-800-221-0932
rev. 1-31-08
INST99-4012
Cutting tool
www.metraonline.com
© COPYRIGHT 2001-2008 METRA ELECTRONICS CORPORATION
APPLICATIONS
BUICK
CHEVROLET (cont.)
CHEVROLET (cont.)
OLDSMOBILE (cont.)
Ninety Eight 1984-90*
Century 1982-96*
Camaro 1997-99
Suburban 1989-91*
Omega 1983-84*
Electra 1984-94*
Caprice 1991-93*
Suburban 1995-02
Silhouette 1990-95*
Estate wagon 1984-94* Caprice 1994-96
Tahoe 1995-02
Silhouette 1996*
LeSabre 1984-94*
Cavalier 1982-90*
Van (full) 1988-95*
Silhouette 1997-99
Park Ave. 1984-94*
Cavalier 1991-94*
Venture 1997-99
Toronado 1982-85*
Reatta 1990-91*
Cavalier 1995-99
GMC
PONTIAC
Regal 1984-87*
Celebrity 1982-83*
Jimmy (full) 1989-91*
6000 1982-91*
Riviera 1983-85*
Celebrity 1984-87*
Jimmy 1998-02
Bonneville 1982-86*
Riviera 1990-95*
Citation II 1985*
S15 Jimmy 1982-85*
Bonneville 1987-93*
Roadmaster 1991-94* Corsica 1991-96*
S15 Jimmy 1986-94*
Bonneville 1994-99
Skyhawk 1982-89*
Corvette 1984-89*
S15 Pickup 1982-85*
Fiero 1984-88*
Skylark 1983-85*
Corvette 1997-02
S15 Pickup 1986-93*
Firebird 1982-84*
Skylark 1987-89*
El Camino 1985-88*
Safari 1985-89*
Firebird 1985-92*
Skylark 1990-95*
Express 1996-00
Safari 1990-95*
Firebird 1993-02
CADILLAC
Impala SS 1994-96
Safari 1996-02
Grand Am 1985-91*
Cimarron 1982-88*
Lumina 1990-94*
Savana 1996-00
Grand Am 1992-95*
DeVille 1985-93*
Lumina 1995-99
Sierra 1995-02
Grand Am 1996-98
Eldorado 1984-91*
Lumina APV 1990-95*
Sonoma 1998-02
Grand Am 1999-00
Escalade 1999-02
Lumina APV 1996*
Suburban 1989-91*
Grand Prix 1985-87*
Fleetwood 1985-93*
Malibu 1997-99
Suburban 1995-99
Grand Prix 1990-93*
Seville 1984-91*
Monte Carlo 1985-88*
Van (full) 1988-95*
Grand Prix 1994-96
Monte Carlo 1995-99
Yukon 1995-02
CHEVROLET
Grand Prix 1997-00
Nova 1985-88*
OLDSMOBILE
Astro 1985-89*
Montana 1999
Pickup 1995-02
Achieva 1992-95*
Astro 1990-95*
Sunbird J-2000 1982-88*
S10 Blazer 1982-85*
Bravada 1991-94*
Astro 1996-02
Sunfire 1995-99
S10 Blazer 1986-94*
Cutlass Calais 1984-91* TransSport 1990-95*
Beretta 1991-96*
S10 Pickup 1982-85*
Cutlass Ciera 1982-96* TransSport 1996*
Blazer (full) 1989-91*
S10 Pickup 1986-93*
Cutlass Supr. 1984-88* TranSport 1997-98
Blazer 1998-02
S10
Pickup
1998-02
SATURN
Delta 88 1986-88*
Camaro 1982-84*
Silverado 1999-02
(all models) 1991-94*
Firenza 1982-89*
Camaro 1985-92*
3
Fig. A
Fig. B
2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft
nuts. (see Fig. A).
DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate. Slide the DIN
cage into the Radio Housing and secure by bending the metal locking tabs down. Slide the
aftermarket head unit into the cage until secure. (see Fig. B).
* THE FACTORY MOUNTING BRACKET(S) MUST BE RETAINED AND USED WITH THIS VEHICLE.
ALL VEHICLES
1
2
"B"
4
A
5
B
C
"B"
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Please call Metra's Technical Support line
for individual dash disassemblies.
Mount the Metra bracket(s)
OR factory bracket(s) to the Housing with
Carriage Bolts and Keps Nuts supplied
("B"). Choose the desired Faceplate and
snap it onto the front of the Radio Housing.
1
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with those screws
previously removed.
2

advertisement

Key Features

  • Installation kit for aftermarket radios
  • Compatible with General Motors vehicles
  • Supports both 2-shaft and DIN head units
  • Includes mounting hardware and wiring harness connector
  • Detailed installation instructions provided

Frequently Answers and Questions

What vehicles is this installation kit compatible with?
The kit is compatible with General Motors vehicles from 1982 to 2002 equipped with J-2000 panel-style factory head unit provisions. Refer to the 'Applications' section for specific vehicle models.
What types of head units are compatible with this kit?
The kit supports both 2-shaft and DIN head units. For 2-shaft head units, the aftermarket head unit is secured with shaft nuts. For DIN head units, remove the shaft supports from the Faceplate and slide the DIN cage into the Radio Housing.
What tools are required for installation?
You will need a Phillips screwdriver and a cutting tool. Refer to the 'Tools Required' section for more details.

Related manuals

Download PDF

advertisement