M22 Owner s Manual
MONITOR 22
TM
Heating System
Owner's Guide
IMPORTANT : READ THIS OWNER'S GUIDE CAREFULLY AND
THOROUGHLY BEFORE INSTALLING OR USING
YOUR HEATER.
RETAIN THIS OWNER'S GUIDE FOR FUTURE
REFERENCE.
€ )
i. M O N I T O R
P R O D U C T S
I N C
SAFETY ALERT SYMBOL
These symbols appear at important safety precautions and should be understood
and followed by the owner to assure safe operation of the heater.
For Quick Reference
SECTION A: ^Important Caution
SECTION B: Specifications
Special Features
Safety Features
SECTION C: Tools Needed for Heater Installation
Accessories You May Need
Window Installation
Flue Pipe Extentions
SECTION D: Heater Installation
Flue Pipe Clearances
SECTION E: Fueling
Refueling
Fueling Options Available
External Tank Installation
Empty Fuel Tank
SECTION F: Starting Instructions
SECTION G: Adjusting Room Temperature
SECTION H: Turning Off the Heater
SECTION I : Relighting the Heater
SECTION J: Programming the Heater
Setting the Clock
Programming for Automatic Heater Operation
Manual Operation
SECTION K: Protective Features
Loss of Power-Automatic Reset
Electrical Fuse
Overheat Prevention
SECTION L: Care of the Heater
SECTION M: Troubleshooting Guide
COPYRIGHT ^ MONITOR PRODUCTS, INC.,
-
•
•
Page
1
5
5
5
6
7
7
8
9
10
15
16
16
16
19
20
21
21
21
22
22
23
23
24
24
24
24
25
27
SECTION A
IMPORTANT CAUTION
AWARNING
USE ONLY CRYSTAL CLEAR KEROSENE. NEVER
USE GASOLINE, WHITE GAS, CAMP FUEL OR
OTHER FLAMMABLE LIQUIDS. USE OF SUCH
FUELS CAN RESULT IN AN EXPLOSIVE FIRE AND
CAUSE SEVERE INJURY.
KEROSENE ONLY
GAS
ACAUTION
1. Make sure that there is no fuel leakage from fuel tank and fuel pipe joint.
2. Make sure that flue pipe (exhaust pipe, air supply hose) is connected
properly.
MONITOR 22"
3 Keep heater clean and do not store any flammable items on or near the
heater.
4 Don't use the heater for drying clothes.
5 Should anything abnormal occur in the heater, remain calm, turn it off (do
not unplug) and contact your Monitor dealer.
6. Risk of burns.
Flue piPe and louver
temperature.
ma
y have high surface
7. Do not place yourself or others too close to the heater.
8. Installation of heater in extreme humidity or dust areas is not
recommended.
Any removal of unit parts or remodeling is strictly forbidden.
Do not sit on the heater.
Placing ornaments or plants is not recommended.
Excess heat may cause damage to ornament or plant and overwatering
or spilling of water may cause shock to you or damage to the
heater.
10. In areas of heavy snow accumulation, flue pipe may need to be installed higher to avoid being buried.
In open areas with strong wind, a wind break may be necessary to avoid exhaust gases being blown
back into the intake and causing poor combustion.
u- 24"min .
Long
^^ ^
Extension*
kit
:>—
f
Must be higher.
J
Snow
i
,
MONITOR 22"
11. Do not install nor exhaust the flue pipe into a crawl space or underneath floor nor into a flue or chimney.
X
-Flue Duct
12. OPERATING ALTITUDES HIGHER LIMITS
This heater is designed to be used no higher than 3000FT above sea level. Do not operate at altitudes
higher than 3000FT above sea level.
13.OPERATING TEMPERATURE LIMITS
Please use the Monitor within the range of temperatures indicated by the shaded area shown on the graph
below.
Operating Temperature Limits
Point A
Inside Area Temperature — 4°F
Outside Temperature
— 22°F
Point B
Inside Area Temperature 60°F
Outside Temperature
-40°F
10
0
20
Inside Area Temperature (T)
40
SECTION B
_
SPECIFICATIONS
Model
Fuel Type
Heater Efficiency
Heat Rating
Heater Output
Fuel Tank
Fuel Consumption
Power Source
Power Consumption
Heated Air Delivery
Vent Pipe Hole
Dimensions
Weight
Monitor 22
Crystal Clear Kerosene
93%
High: 22,000 BTU/hour
H.Medium: 17,400 BTU/hour
LMedium: 11,700 BTU/hour
Low: 9,600 BTU/hour
High: 20,400 BTU/hour
H.Medium16,200 BTU/hour
L.Medium: 10,900 BTU/hour
Low: 8,900 BTU/hour
1.32 Gallons; Separate tank optional
High: 0.164 Gallon/hour
H.Medium: 0.13 Gallon/hour
L.Medium: 0.09 Gallon/hour
Low: 0.07 Gallon/hour
120 Volts AC; 60 Hz
Ignition: 250 Watts
Operation: 55 Watts (Average)
High: 176 Cubic feet/minute
H.Medium: 176 Cubic feet/minute
L. Medium: 113 Cubic feet/minute
Low: 113 Cubic feet/minute
2M-inches Diameter
Height: 25.6 inches
Width: 20.9 inches
Depth: 12.4 inches
55 Pounds, empty
* When considering heat of condensation is lost then net efficiency is 87%.
SPECIAL FEATURES
AUTOMATIC IGNITION
DUAL BLOWERS: Separate fans for combustion and
room air circulation.
THERMOSTATICALLY CONTROLLED: Adjusts to the
desired room temperature.
BUILT-IN TIMER: Heater will automatically operate as
programmed by the user.
INDICATOR LIGHT: Easy-to-see signals show-when
heater is in operation, when timer is activated,
and when the burner is operating in low, medium
or high modes. Indicator lights also warn against
low fuel level.
AUTOMATIC RESET AFTER POWER FAILURE: Heater
will automatically resume operation (in manual
mode) after power is restored.
CHOICE OF FUEL SUPPLY: Built-in capsule tank or
connect to separate tank.
MULTIPLE HEAT EXCHANGER: Extracts 93% of heat
from burner.
5
CLEAN OPERATION: Products of combustion are vented
outside.
CONSUMES NO ROOM AIR: Air for combustion is
drawn from outside.
EASY INSTALLATION includes all parts required for
standard installation.
SAFETY FEATURES
SAFE RE-LIGHTING: Heater will not restart until its
combustion chamber has cooled.
ELECTRICAL PROTECTION: Heater automatically shuts
off in the unlikely event of a malfunction in the
electrical circuitry or disruption of the power supply.
NO EXHAUST IN ROOM: Products of combustion are
discharged outdoors.
FLUE PIPE: Outside air is drawn through a pipe-withina-pipe venting system. This process preheats
combustion air and regains heat from exhaust
gases.
4/1PI
MONITOR 22
SECTION C
Before installing your heater, be sure to check and comply with local and state building and electrical codes
that may apply to vented Heaters in your area. Permanent wiring must be installed by a licensed electrician.
TOOLS NEEDED FOR HEATER INSTALLATION
Check the following charts to be sure you have all the tools required to install your Monitor 22 Heating System.
STANDARD TOOLS
Phillips Head Screwdriver
Steel Tape Measure
Pen or Pencil
Exterior Caulk
Yardstick or Long Straight Edge
Soapy Water
APPLICATION
Installation of Heater Parts
Taking Measurements
Marking Drilling Location
Caulking Between Packing and Wall
Checking Angle of Hole for Flue Pipe
Lubricating Sleeve Hardware
SPECIAL TOOLS
APPLICATION
Electric Drill
inch Hole Saw Attachment
Long 1A inch Drill Bit
Level
Accommodating Hole Saw and Drill Bit
Cutting Hole for Flue Pipe
Drilling Pilot Hole Through Wall
Checking Angle of Hole for Flue Pipe and for checking
heater level.
Fig. 1
6
ACCESSORIES YOU MAY NEED
Check the list below and see your MPI dealer for accessories you may need or want for installation of your heating system.
APPLICATION
inches
For use where wall thickness is up to
For use where wall thickness is up to 20 inches
For small capacity, gravity fed outside fuel supply
For use with large capacity tank where gravity feed is not
practical
For use where "through-the window" flue pipe installation
is desired
For use where "standard" installation is not practical
ACCESSORY
Medium Flue Pipe
Long Flue Pipe
Wall Mounted Fuel Tank
Electric Suction Pump
P/N 8206
P/N 8005
P/N 8201
P/N 1100
1101
Window Installation Kit P/N 8208, 8209
(See Window Installation below)
Extra Short, Short, Medium or
Long Extension Kit or Elbow Adapter Kit
(See Flue Pipe Extensions, page 8)
Fitting and Tank
For large capacity fueling: To be dealer installed
WINDOW INSTALLATION
The use of "through-the-window" installation for your
flue pipe will require a window installation kit and one
of the 4 (Extra short, Short, medium or long) extension
kits.
In order to determine wihch extension kit is required
measure the distance from the floor to the TOP of
your window sill (see Figure 2) and refer to the chart
below.
\
Fig. 2
IF THE MEASUREMENT IS:
20% to 25 inches
25 to 33% inches
33% to 51y* inches
51M to86M inches
YOU NEED:
Extra Short Extension Kit
Short Extension Kit
Medium Extension Kit
Long Extension Kit
Elbow Adapter Kit
P/N 8212
P/N 8004
P/N 8003
P/N 8002
P/N 8213
NOTE: Window kit installation is prohibited when the window is required to meet the local building code requirements for ventilation, emergency escape, or rescue.
One or more Elbow Adapter Kit may be needed if heater is installed on inside wall.
-
MPi
MONITOR 22
FLUE PIPE EXTENSIONS
Four standard extension kits are available from your
Monitor dealer. Most installations can de made with
one of these kits. In special cases, custom installations may be required. These may be made with components purchased from your dealer.
2. These elbows should include the one used at the
heater but not the one on the air supply hose nor the
integral bends in the flue pipe. (See Figure 3)
3. The correct damper as shown on Page 13 must be
used.
In any installation the following limitations MUST NOT
BE EXCEEDED:
1. The total length of either the intake or exhaust pipe
should not exceed 10 feet with 3 elbows, 13 feet with
2 elbows, or 16 1/2 feet with 1 elbow.
Exhaust Elbow
Air Supply Hose
90" Joint
Flue Pipe
Fig. 3
* Do not count
8
SECTION D
_
HEATER INSTALLATION
Step 1: Fill Out Owner Registration Card
Remove your owner registration card from the plastic
packet on the outside of the shipping carton. It should
be filled out and mailed as soon as possible.
Step 2: Check for Parts
Before discarding packing materials, be sure you have
located the following:
Flue Pipe
Sleeve Nut
Spill Tray
Room Temp. Sensor (attached to the rear of the
heater)
Cardboard Template
"STANDARD" Damper
Wall Clamps (2)
Rubber Packing
Joint Pipe
Cloth Insulation Cover
Outer Flange
Pipe Holder
Small Bag of Screws
Tapping, Type A —
Tapping, Type A —
Small Plastic Syringe
Step 3: Choose a Location for Your Heater
In choosing a location for your heater, the following
guidlines must be considered:
• The heater MAY be installed on combustible floors.
• The area around the heater should be free of obstacles that might interfere with the free flow of air.
Allow the clearances shown in Figure 5.
39"
Fig. 5
For securing
sleeve and
wall clamps
For securing
wall clamps
Tapping
Tapping
SIZE
Fig. 4
• The heater must not be installed in a combustible
fireplace.
• An AC wall outlet must be within reach of the heater's power cord. Extension cords must not be
used.
• The area outside where the flue pipe will emerge
should be free of foliage, fuel storage tanks and
flammable objects. Air should circulate freely in
the area. Allow the clearances shown in Figure 6 on
the next page.
• The wall where flue pipe hole will be cut should be
free of plumbing pipes, electrical wires, studs, air
ducts and other obstacles.
NOTE: Use the cardboard template provided with your
heater for flue pipe location.
4AP\
MONITOR22
FLUE PIPE CLEARANCES
Flue pipe installations should provide for venting to an unconfined space through which there is a free flow of
outdoor air. Clearances to adjacent walls or obstacles must comply with the requirements shown below.
Frontal Clearance
Combustible iiiiiNiiiiiimiimmiiimiilii
A CAUTION:
Do not attach anything onto the outlet
of the flue pipe.
24" (60cm)
or
more
Mi,
Wall
or4
more
Any construction
above Flue Pipe
must not come
within 24" (60cm)
of front obstacle
24" (60cm)
or more
.Flue Pipe
I Front Obstacle
8" (20cm)
or more
Heater
Ground or slab surface
Overhead Clearance
Non-combustible
Combustible -
Combustible
Ground or slab surface
Body
Clamp
Side Clearance
Side obstacle
18" (45cm)
or more
Heater
Flue Pipe
-Wall
IMPORTANT:
(1) In areas of heavy snow falls, ground surface clearance
must be increased according to average snow falls, to
prevent flue pipe from being buried.
Long
Extension1
kit
(2) In open area with strong wind, a wind break may be
necessary.
u_ 24"min
'1
f
Must be higher.
Snow
Fig. 6
10
Use the template to position the hole to be drilled.
The "red dot" indicates the exact center of the hole.
Using an electric drill and a long drill bit, make a
pilot hole through the wall (Figure 7). Be sure the hole
extends through the outside wall.
Step 4: Drill a Pilot Hole
NOTE: The following directions apply to "standard"
installation. For other methods, follow instruction
included with accessory kits.
For walls up to S'/z inches thick, use a short
flue pipe; for walls up to 14'/z inches thick, use
a medium flue pipe; and for walls up to 20 inches
thick, use a long flue pipe.
Position of hole-
- Template
o
Fig. 7
/!\ CAUTION: The opening on the inside wall should be approximately % inch higher than on the outside wall so
the flue pipe will slope downward when installed. This will allow condensation to drain outdoors.
Step 5: Cut the Hole for the Flue Pipe
Using a hole saw attachment and an electric drill, cut
a 2M inch diameter hole through the inner and outer
walls (Figure 8).
Fig. 8
After the hole is cut, use a straight edge and a level
to be sure the inside opening is approximately
higher than the outside opening.
11
4API
MONITOR 22
with the 3 #8xMapping screws(Figure 9). (See Figure
4 for screw size and application.)
Step 6: Install the Flue Pipe
From INSIDE the building, insert the flue pipe (with
arrow pointing "up") into the hole. Fasten the flue pipe
tapping screw
Fig. 9
Step 7: Install the Outer Flange
Apply caulking material to the inside ridge of the
rubber packing (Figure 10).
Holding the "Up" mark to the top, slide the rubber
packing onto the sleeve (caulk side to the wall).
NOTE: If it is difficult to slide the packing onto the
sleeve, apply soapy water to the inside of the
packing.
Once the rubber packing is in place, slide the outer
flange onto the sleeve with the conical side pointing
outward (Figure 11).
Screw the flue pipe nut onto the flue pipe grooves,
and tighten it firmly (Figure 11).
Rubber Packing
Fig. 10
Flue Pipe Nut.
Outer Flange
Fig. 11
12
Step 8: Install the Spill Tray
Place the spill tray on the floor where you plan to
locate your heater.
Remove the 2 sets of screws from the cabinet (Figure
12).
Position the heater on the spill tray so the legs of the
cabinet fit into the circular indentations in the spill
tray (Figure 12).
-
Step 11: Connect the Heater to the Flue Pipe
Move the heater toward the wall, guiding the joint pipe
into the center port of the flue pipe (Figure 14).
Be sure the joint pipe is completely inserted into the
flue pipe.
Screws
Retainers
Legs
Spill Tray
Fig. 12
Step 9: Level the cabinet
In order for heater to operate properly. It must be
positioned on a level surface. Ensure proper leveling
by adjusting each leg and by using a carpenters level
to check both side to side, and front to back level
condition.
Attach and tighten both sets of retainers and screws.
Step 10: Install the Joint Pipe
At the rear of the heater, slide the large end opening
of the joint pipe into the exhaust port outlet of the
heater. Be sure the joint pipe is fully seated. Slide the
fabric cover over the joint pipe (Figure 13).
Step 12: Install the Air Damper
If installation is standard (that is no extention kits
required), place the air damper marked with a
"STANDARD" over the air intake flange on the flue
pipe (Figure 15).
Place the hose band around the end of the air supply
hose. Push the air supply hose onto the air intake
flange and secure the hose with the hose band.
Fabric Cover
Air Supply Hose
Joint Pipe
Fig. 13
13
.
44PI
MONITOR 22
NOTE:
The "STANDARD" damper is to be used with
extension kits up to a total overall length of 20
inches and a maximum of 3 bends (90° elbow).
Air damper is not used when extension kit or kits
exceed 20 inches.
Step 15: Recheck the Heater
Before proceeding, check again to be sure there are
no flammable materials close to the heater. Check to
be sure the heater is level.
Examine the flue pipe to be sure connections are tight.
Step 13: Install the Flue Pipe Holder
Place the ring of the flue pipe holder around the flue
pipe. The other side of the holder hooks in a slot directly above the joint pipe at the rear of the heater
(See Figure 16).
Flue Pipe Holder
Fig. 16
Step 14: Secure the Heater
Insert the narrow ends of the 2 wall clamps into sockets
on the rear of the heater.
Loosen the adjustment screws and extend the clamps
until they touch the wall. Fasten the clamps to the
wall with 2 #8x% tapping screws.
NOTE: If use of wall clamps is not feasible or
practical, the heater should be secured by
screw to floor through punched hole in spill
tray.
14
SECTION E
-'
FUELING
A WARNING: USE ONLY CRYSTAL CLEAR KEROSENE. NEVER USE GASOLINE, WHITE GAS, CAMP FUEL OR
OTHER FLAMMABLE LIQUIDS. USE OF SUCH FUELS CAN RESULT IN AN EXPLOSIVE FIRE AND
CAUSE SEVERE INJURY.
Step 1: Lift Out the Capsule Fuel Tank
To fill with fuel, open the tank cover and lift out the
capsule fuel tank (see Figure 17). Turn the tank upside down, and remove the fuel cap. If the fuel cap is
difficult to unscrew, press the valve in the center, and
remove.
"FULL" Fuel Level
Fig. 18
Step 3: Reinstall the Capsule Fuel Tank
Replace and tighten the fuel cap. To insure proper fuel
flow, be sure the cap is secured correctly.
Install the tank with the arrow pointing forward, and
close the tank cover (see Figure 19).
Fig. 17
Step 2: Using a Siphon
A siphon is not included with your Monitor 22. You
may obtain one from your Monitor dealer.
To operate a siphon, insert the straight tube into the
kerosene container. Insert the siphon's flexible hose
into the capsule fuel tank (see Figure 18).
Watch the fuel gauge on the capsule tank closely.
As the fuel begins to near the full level (see Figure 18),
stop the flow by turning the vent knob on top of the
siphon counter-clockwise. Remove the siphon slowly
to allow excess kerosene to drain back into the
container.
Fig. 19
15
44PI
MONITOR 22
REFUELING
EXTERNAL TANK INSTALLATION-Gravity Fed
NOTE: When the red light marked "Empty" illuminates
and flashes, a buzzer will sound for twenty
seconds. The burner mode is changed to "Low"
automatically, and then, the heater will shut off
after 30 minutes.
The remaining burning time is indicated at the
display window.
When using external tank, changes in heater installation
and pipe connections are required.
PREPARATION AT HEATER
Stepl:
Remove the capsule fuel tank, and the fuel filter from
the fuel sump tank (see Figure 20).
30 min
20 sec
•Burner shuts off.
Fuel Filter
Buzzer sounds
•Red light flashes.
•Burner mode change to "Low"
Tank
Stepl:
When the red light marked "Empty" illuminates and
flashes, buzzer sounds, press the Operation Switch
to put it in the "OFF" position and wait 15 minutes for
the heater to cool.
Step 2:
If kerosene has accumulated in the spill tray or in the
chamber which holds the capsule fuel tank, clean
with a towel or rag. Remove any flammable items
situated near the heater or flue pipe.
Step 3:
Follow directions under "Fueling".
FUELING OPTIONS AVAILABLE
Fig. 20
In addition to the standard capsule tank, the following
fueling options are available for use with your Monitor
22.
1. Wall Mounted Fuel Tank: For small fueling needs.
This system, available from your MPI dealer, is
gravity fed and easily installed by anyone handy in
making home improvements.
2. Gravity Fed Large Capacity External Tank: Practical
for large heating needs where bulk delivery of
kerosene is available.
This system should be
installed by a qualified plumber or fuel supply
technician.
3. Large Capacity External Tank with Pump: For large
heating needs where a gravity fed system is not
practical.
An electric suction pump, especially
designed for use with your Monitor Heating System,
is available from your dealer.
When using a gravity fed tank or pumping system to
supply fuel, the inlet pressure to the heater must not
exceed 2.5 psi.
NOTE: When using a separate fuel tank with your
Monitor22, the "Empty" light will NOT signal an
empty tank. Watch the gauge on the tank to
avoid running out of fuel.
16
CtAn O •
Remove fuel with the siphon, remaining fuel must be sucked up with the plastic syringe (see Figure 21).
Fuel Sump Tank
Plastic Syringe
Fig. 21
Step 3:
Wipe off the fuel sump tank with a towel or rag (see
Figure 22).
Step 4:
Remove the nut at the rear lower side of the heater.
Collect fuel draining from the heater into a container.
Hold the nipple with a wrench and loosen the nut with
the other wrench (see Figure 23).
Nipple
Wrench
Fig. 22
Container
Fig. 23
17
4/1PI
MONITOR 22
Step 5:
Insert the rubber plug into the disconnected pipe (see
Figure 24).
Wipe off spilled fuel.
Rubber Plug
Bend the pipe aside
Fig. 24
Step 6:
Remove the screws at the louver, and carefully remove
the louver and front panel (see Figure 25).
Louver
Front Panel
Fig. 25
Step 7: Connect the plugs of red and brown wires marking "U" coming out from the printed wiring board for
turning off the function of the fuel empty float switch (see Figure 26).
Printed Wiring Board
Lead Wires
Color: Red/Brown
Marking : "U"
NOTE: Plug in male, female connectors to bypass
circuit.
Plug For Short Circuit
Fig. 26
18
-(X
Step 8: Replace the front panel and the louver.
Step 9: Connect the fuel line from External Tank as follows.
NOTE: External tank installations must comply with the
National Fire Protection Association code NFPA
31 or locally applicable codes, such as the 1979
Uniform Mechanical Code No.5-1. that are
consistent with NFPA 31. Check with your local
building official.
To install a large capacity, gravity fed external tank,
follow the instructions below, and refer to Figure 27
for one possible installation. Use of a qualified installer
is recommended.
• Installation height of the bottom of the fuel tank
should be 16 inches or more above the floor surface
on which the heater stands. This insures that inlet
fuel pressure will be sufficient.
• The top of the fuel tank should be no higher than
SKfeet above the floor under the heater. This insures
that inlet fuel pressure will not be excessive.
• The horizontal length of piping should not exceed
•
•
•
•
•
•
100 feet and should be free of sharp bends or
obstructions.
Piping should include no inverse U-type bends (to
avoid air locks, which could block the fuel supply).
Only %inch OD copper tubing should be used.
The tubing should be bent carefully to avoid crimping.
A fuel filter is recommended for use on the fuel line
near the tank, and a shut-off valve should be installed
at the tank.
Flare connections should be used at the fusible link
valve connection on the heater and at the fuel filter
to be installed at the tank.
The fuel tank should be located no closer than 6
feet to a source of heat.
The fuel tank should have an opening for filling on
the top and a vent with a weather-proof cap on the
side. On some tanks the vent and fill spout use the
same opening.
When using a gravity fed tank to supply fuel, the inlet
pressure to the heater must not exceed 2.5 psi.
Outdoor Fuel Tank
Shut-off Valve
Fusible Link
Valve Connection
NOTE: Fuel tank must be a minimum 3 feet away from flue pipe.
Fig. 27
EMPTY FUEL TANK
If at any time during the operation of your heater you
find.
• Burner Status indicators are blinking.
• No heat
• No flame
You can assume you are out of fuel.
Should this situation occur, take the following steps.
Step 1: Turn the Heater Off
Press the Operation Button to put it in the "Off" position.
Step 2: Refuel
Refill your fuel tank with kerosene.
Step 3: Turn the Heater On
Press the Operation Button to put it in the "On" position.
MPI
MONITOR22
SECTION F
STARTING INSTRUCTIONS
Step 1: Plug in the Heater
plug in the AC cord, and route it away from the area
of the flue pipe. It is recommended that no other
appliance share the same outlet.
Step 2: Prime the Heater
If using the heater for the first time, or if the heater
has not been in operation for sometime, press the fuel
set lever at the lower right hand side of the cabinet
and release it slowly 2 or 3 times (Figure 28).
Step 3: Set "ON" Button
Depress the operation button to put it in the "ON"
position. The "Operation lamp" lights indicating "Set
room temperature" and "present room temperature".
Burner status lamps will light ana ignition will start
after approximately three minutes. In 5 to 10 minutes
the circulation fan will start to operate, and warm air
will be felt coming through the cabinet grill.
/j\ CAUTION: Do not continue pressing lever repeatedly as this may cause overfilling of constant
level valve inside.
Fuel Set Lever
Fig. 28
RUN
AUTO
EMPTY
BURNER STATUS
000007
LOW
HIGH
OPERATION
ON/OFF AUTO
TIMER SELECTOR
CLOCK CLOCK
/TEMP SET 1st 2nd 3rd 4th
ROOM
SET
TEMP
AM
PM
r~i • i"~ n
i_j - o o
TIME/TEMP SET
HOUR MINUTE SET CLEAR
CLF
UP
DOWN
Fig. 29
20
SECTION G
ADJUSTING ROOM TEMPERATURE
Press either the "UP" or "DOWN" button to set the
digital set room temperature indicator to the desired
temperature, and then press the "SET" button. After
the room temperture has stabilized in 1 to 2 hours,
adjust the temperature to the desired level.
The lights on the control panel will indicate the level
of heater operation — low, medium or high. The heater
will automatically change its heat output until the
desired room temperature is reached. While it cycles,
you may hear the circulation fan change speed.
Depending on the output required to maintain the
desired room temperature, the indicator lights will
illuminate in the following pattern:
BURNER MODE
LIGHT PATTERN
High
H.Medium
L Medium
Low
Off
8
6
4
2
indicators
indicators
indicators
indicators
— On
— On
— On
— On
*No lights on
• The heater will shut itself off temporarily when the desired room temperature has been reached and restart automatically when
necessary to maintain room temperature.
NOTE: The heater may display room temperature 4 degrees above set temperature, depending on heater load
conditions, before shutting itself off.
SECTION H
SECTION I
TURNING OFF THE HEATER
RELIGHTING THE HEATER
To turn off the heater, press the Operation Button to
put it in the "Off" position (Figure 29). The operationlight will go out, and the fuel flow will stop.
After turning heater off the fans will continue to run
until unit has cooled down to the point where the fans
will automatically stop.
Automatic controls prevent your heater from relighting
after the Operation Button has been set to "Off" until
heater has cooled.
If the Operation Button is put in the "On" position
during the cooling period, the heater will automatically
relight at the end of the period.
t
21
4/IPI
MONITOR22
SECTION J
PROGRAMMING THE HEATER
SETTING THE CLOCK
Step 1: Set the Timer Selector
Move the Timer Selector Knob to the "Clock Set" position. The LED indicator in the Display Window will show
88:88 at this point.
DISPLAY WINDOW
RUN
AUTO
EMPTY
a
LOW
ROOM
SET
BURNER STATUS
TEMP
AM
PM
HIGH
/- n
oo
: 88
TIMER SERECTOR
ON/OFF
\TIMER SELECTOR
CLOCK\ CLOCK
AUTO /TEMP \ SET 1st 2nd 3rd 4th
TIME/TEMP SET
OPERATION
OPERATION BUTTON
Step 2: Set the Hour
Press the "Hour" Button until the correct hour (either
A.M. or P.M.) appears in the window.
TIME
]]
TEMP |l
l|
HOUR MINUTE SET
UP
CLEAR
DOWN
Fig. 30
Step 4: Display the Current Time
To display the current time, move the Timer Selector
Knob to the "CLOCK/TEMP" position.
Step 3: Set the Minute
Press the "Minute" Button until the correct time
appears in the window.
Immediately press the "Set" Button.
NOTE: If the "Set" Button is not pressed within 1 minute
after the time is set, the programming will be
cancelled.
22
PROGRAMMING FOR AUTOMATIC HEATER OPERATION
The monitor 22-Heating System is designed to provide
up to 4 times Time/Temperature programming a day.
To program the heater for automatic operation, refer
to Figure 30 and follow the steps below.
Step 1: Set the 1st Time/Temperature
Move the Timer Selector Knob to the "1st" position.
Press the TIME Button. Set the 1st desired time by
pressing the HOUR and MINUTE Buttons as described
under "Setting the Clock".
NOTE: Be sure to set the time correctly for either AM
or P.M.
Press the "SET" Button.
Press the "TEMP" Button.
Set the 1st desired temperature by pressing the
"UP and DOWN" Buttons.
Press the "SET" Button.
Step 2: Program the Remaining Times
With the Timer Selector Knob in the appropriate
positions, program the 2nd, 3rd, 4th times as described
above. Be sure to press the Set Button after each time
is programmed.
Step 3: Activate Automatic Operation
To operate your heater automatically, press the "Auto"
Button on the control panel. When you have done this,
the "Auto" light will illuminate, confirming that the heater
is in the automatic operation mode.
Step 4: Clearing an Automatic Setting
Should it become necessary to clear an automatic
setting, slide the Timer Selector Knob to the appropriate position, and press the "Clear" Button.
IMPORTANT: The heater will not operate in automatic
unless the "ON" "OFF" switch is in the
"ON" position.
MANUAL OPERATION
When there is no further need for automatic operation,
or when you wish to override it, press the "AUTO"
Button again. Your heater will operate thermostatically
at the setting you choose, and the clock will continue
to operate.
23
It is important to note that activating manual operation
does NOT clear the automatic programming. To return
to automatic operation, simply press the "AUTO"
Button.
4/IPI
MONITOR 22
SECTION K
PROTECTIVE FEATURES
OVERHEAT PREVENTION
LOSS OF POWER-AUTOMATIC RESET:
If your heater overheats, a thermostatic switch will
automatically stop the flow of kerosene and extinguish
the flame. The Burner status indicators are blinking.
Restore heater operation by following the steps
below.
NOTE: Other symptoms listed in the trouble shooting
chart may cause burner status indicators to
blink, besides an overheat situation.
NOTE: If power to the heater is interrupted, a thud-like
noise may be heard in the combustion chamber.
This is normal, and should not cause alarm.
Once power is restored, your heater will resume
operation in the MANUAL mode and maintain
room temperature according to the setting
temperature you've selected by using the slide
selector for the reset temperature at the lower
right hand side of the cabinet (Figure 31).
When the "TIME BUTTON" is pressed or the
Timer Selector knob is moved to the "Clock
Set" position, the Display Window will show
88 : 88 indicating the need to reset the clock
and re-program the heater for automatic
operation.
REMARK: In order to display reset temperature,
it should be set before the heater is plugged in
and energized.
New reset temperature selected after plugged
in will take effect only after a power loss.
RESET TEMPERATURE
50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80
Step 1: Turn the Heater Off
Press the Operation Button to put it in the "Off" position.
Step 2: Allow the Heater to Cool
Wait approximately 30 to 45 minutes for the heater to
cool completely.
Step 3: Unplug the Heater from the Wall Outlet.
Step 4: Remove Obstructions
The overheated condition may be caused by obstructions
blocking the air flow to the heater . Check:
• The front of the heater
• The circulation fan (on the back of the heater).
• The flue pipe (outside)
Step 5: Remove the Louver
Remove the screws at the louver, and carefully remove
the louver (Figure 32).
.euro
Fig. 31
Louver
ELECTRICAL FUSE
In the unlikely event of a failure in the heater's
electrical system, a fuse will "blow" and interrupt the
power. Do not attempt to change the fuse.
Contact your MPI dealer for the name of a trained
and certified service representative in your area.
Fig. 32
Remove any accumulation of dust or other matter that
may be covering the burn chamber and the heat
exchangers inside the heater.
Step 6: Replace the Louver
Step 7: Plug in the Heater
Step 8: Re-program the Heater
Step 9: Turn Heater On
/\ CAUTION: If the unit overheats a second time, turn
it off and contact your MPI dealer for
service.
24
SECTION L
r
CARE OF THE HEATER
Push operation switch to "OFF" remove the AC Plug from the wall outlet and wait approximately 30 minutes for
the heater to cool before performing any of the following steps.
Step 1: Retrieving Objects from Inside the Heater
Should an object fall inside the heater, through the
grill openings, it must be removed to avoid affecting
the operation of the heater.
After allowing the heater to cool, remove the front
cover panel. (See Step 5 of the previous section.)
After the object has been removed, replace the front
cover before attempting to re-start the heater.
Step 2: Cleaning the Cabinet
When the cabinet is soiled, wipe it with a damp cloth.
Restore the shine with a dry cloth.
The use of abrasive household cleaners may dull
the finish.
Step 3: Checking the Flue Pipe
At the beginning of each heating season, check the
inside of the flue pipe. Foreign matter, spider webs,
etc. must be removed.
Be sure all fittings and joints are tight.
Step 4: Cleaning the Interior
Remove the Front Cover Panel (as described in Step
5 of the previous section), and wipe away dust or
other accumulation.
Look for signs of fuel leakage around the joint pipe
and the bottom of the cabinet. If fuel is detected, wipe
it away and if necessary, contact your MPI dealer for
any necessary repairs.
Step 5: Cleaning the Blower Guard
Heating efficiency will be reduced if the blower guard
at rear of the cabinet is blocked with dirt or dust.
Blockage also produces a rise in heat that could cause
the heater to shut off.
Wipe the guard clean at least once a week.
25
Step 6: Cleaning the Fuel Strainer
The strainer of the fuel constant level valve should be
cleaned once a year and before storing heater at the
end of each season.
Step 6-A:
Turn knob of the shut-off valve installed at the fuelinlet
connection to close the fuel line. (See Figure 27).
NOTE: Valve at back of the heater. Turn clockwise to
open, counter clockwise to close.
Step 6-B:
To catch the fuel which will drain out, set the drain
guide made by cardboard below the strainer cover,
with a small container under it. (See Figure 23)
Step 6-C:
Loosen the two screws from the strainer cover and
remove.
Step 6-D:
Remove the strainer and wash with pure kerosene.
Step 6-E:
Return the strainer to its original position.
strainer cover and screw to secure.
Replace
Step 6-F:
Wipe away any spilled kerosene.
Step6-G:
Turn the knob of the shut-off valve to open. Check for
kerosene leakage.
NOTE: Your Monitor may sometimes require more
service than that shown above. Should this occur
please contact your Monitor Products, Inc., dealer
for service. A preseason maintenance check up
could be performed by your dealer to ensure
trouble free operation during the season. Ask
him for details of his routine maintenance
program.
MPI
MONITOR 22
Strainer
Cover
Drain Guide
Container
Fig. 33
Step 7: Storing the Heater
During summer months or long periods when your
heater will not be in operation, take the following
steps:
• Clean off the exterior cabinet with a damp cloth, and
brush or vacuum dust from the grills.
• Remove the AC cord from the wall outlet.
• Cover the heater to protect it from dust.
• DO NOT DISASSEMBLE the heater or extension
kits. Replacement of lost parts is an unnecessary
expense.
26
•
SECTION M
TROUBLESHOOTING
GUIDE
Should symptoms appear during the operation of your heater, refer to the chart below, If you are unable to restore
normal operation, contact your MPI dealer for service.
REMEDY
SYMPTOM
CAUSE
Press Auto Button again.
Timer is in Auto.
Heater does not go on
with operation switch.
Check plug and power source.
AC cord is disconnected
from wall outlet. Power
failure.
Press the fuel set lever at the lower
Out of fuel.
right hand side of the cabinet. Check
"Empty" light. If illuminated, refuel heater.
If separate tank is used "Empty" light
does not operate.
Call your MPI Dealer for Inspection
Igniter Failure.
and/or Replacement.
Refill with fresh kerosene. Section L.
Water in fuel.
Wofe: If strainer is severely clogged,
contact your Monitor dealer to check
and clean the inside of constant level
valve and pump screen.
Clean fuel strainer.
Clogged fuel strainer.
See "Care of the heater"
Section L.
Press fuel set lever on lower right hand
Air pocket in fuel line.
Heater extinguishes after
side of the cabinet and release slowly
lighting.
2 or 3 times.
Out of fuel.
See "Empty Fuel Tank" Section E.
Changes in room temperature. (Slight differences in
room temperature are
normal.)
Poor location of heat
sensor.
Relocate sensor if changes are
uncomfortable.
Automatic timer does not
start heater.
Operation switch is not
in the "ON" position.
Depress operation button to "ON"
position.
Timer is in Manual.
Press Auto Button.
Timer improperly
programmed.
See "Programming for Automatic
Opearation" Section J.
Power interruption.
See "Loss of Power", Section K.
Air bubbles in fuel
controller.
Slowly move temperature selector
several times between the lowest and
the highest positions.
Heater is not level.
Check level.
Poor flame, sounds of
combustion, soot at the
rear of the heater.
Loose flue pipe.
Allow heater to cool completely;
tighten all connections.
Soot on inside of burner
window or exhaust ports
of flue pipe.
Obstruction of combustion
air intake system or
combustion fan failure.
Inspect air intake system and air
supply elbow for blockage. Clean with
a brush,if necessary, and carefully
reconnect.
Flame does not reach
normal size.
Heater switches from
Power interruption; automatic reset.
automatic to manual operation;
display window shows 88 88.
27
See "Loss of Power"
Section K.
r- Monitor 22™ Vented Heating Systems Limited Warrantyn
MONITOR PRODUCTS, INC., warrants each
MONITOR 22 vented heating system sold by it to
be free from defects in material and workmanship,
under normal use and service, for one year after
the date of original retail purchase, subject to the
term and conditions stated below. An extended
warranty period of 36 months is provided for
combustion chamber and heat exchanger. The remainder of the unit is subject to the 12 months
warranty as provided herein.
1. WARRANTOR:This warranty is granted by
MONITOR PRODUCTS, INC., P.O. Box 3408,
Princeton, New Jersey 08543.
2. PARTIES TO WHOM WARRANTY IS EXTENDED:
This warranty shall be extended only to the
original retail purchaser.
3. PARTS COVERED: All
products and parts
manufactured by or for MONITOR PRODUCTS,
INC., except as provided for herein. Replacement
parts are warranted only for the balance of the
original warranty period.
4. PARTS NOT COVERED: The following parts are
not covered by this warranty: fuel filters, venting
kits, extension kits, fuses.
5. REMEDY: If, within the applicable warranty
period, any product or part included in this
warranty proves to be defective in material and/or
workmanship, then MONITOR PRODUCTS, INC.,
shall repair or replace, at its option, the defective
product or part. Service at the point of installation
(not including dealer travel time) will be provided
at no charge to the customer, but must be
performed by a MONITOR PRODUCTS, INC.,
dealer authorized to sell and service the
MONITOR 22 vented heating system.
6. PROCEDURE FOR OBTAINING PERFORMANCE
UNDER THIS WARRANTY: In order to obtain
performance of the obligations under this
warranty, the original purchaser must promptly
(in no event later than thirty (30) days after
discovery of the defect) notify the local MONITOR
PRODUCTS, INC., dealer authorized to sell and
service the MONITOR 22 vented heating system.
Service will be provided during normal business
hours within a reasonable time after the dealer
has been notified of the need for service. If you
are unable to locate a local MONITOR
PRODUCTS, INC., dealer authorized to sell and
service the MONITOR22. vented heating system,
call or write to: SERVICE DEPARTMENT,
MONITOR PRODUCTS, INC., P.O. BOX 3408,
PRINCETION, NEW JERSEY 08543, 201-3290900.
Any claim made under this warranty must be
accompanied by proof of original purchase date
sales invoice or cancelled check showing
serial number is satisfactory evidence.
PART N0.1145 PRINTED IN JAPAN
7. SOLE REMEDY: The remedy and liability for any
breach of warranty, express or implied, set forth
above is the sole and exclusive remedy and the
limit of liability for any such breach.
3
EXCLUSIONS AND IMPLIED WARRANTIES: THIS
WARRANTY DOES NOT EXTEND TO ANY
DEFECT DUE TO THE NEGLIGENCE OF
OTHERS, FAILURE TO INSTALL, OPERATE OR
MAINTAIN THE HEATER IN ACCORDANCE
WITH THE INSTALLATION, OPERATION AND
MAINTENANCE INSTRUCTIONS FURNISHED
WITH EACH NEW HEATER, UNREASONABLE
USE, ACCIDENTS, ALTERATIONS, ORDINARY
WEAR AND TEAR, THE USE OF UNAUTHORIZED OR NON-STANDARDIZED PARTS OR
ACCESSORIES OR THE USE OF ANY FUEL
OTHER THAN GOOD QUALITY KEROSENE
SUCH AS 1K GRADE. ALL IMPLIED WARRANTIES, IF ANY, ARISING UNDER STATE LAW IN
CONNECTION WITH THE SALES BY MONITOR
PRODUCTS, INC., OF ANY NEW HEATER ARE
LIMITED IN DURATION TO THE DURATION OF
THIS WRITTEN WARRANTY. THERE ARE NO
WARRANTIES, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH
EXTEND BEYOND THIS WARRANTY MONITOR
PRODUCTS, INC., SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. WHETHER AS A RESULT OF
BREACH
OF
WARRANTY, NEGLIGENCE,
STRICT LIABILITY IN TORT OR OTHERWISE.
NOTE:SOME STATES DO NOT ALLOW: (A) LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS; OR (B) THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL
DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSIONS
MAY NOT APPLY TO YOU.
9. NO VARIATION OF TERMS: THE PARTIES INTEND THAT THIS WARRANTY BE THE EXCLUSIVE AND FINAL EXPRESSION OF THEIR
AGREEMENT.
No person has the authority to orally, in writing
or in any other way vary the terms, conditions
or exclusions, of this warranty or to make any
express warranties other than those contained
herein.
10. LEGAL RIGHTS: This warranty gives you specific
legal rights and you may also have other rights
which vary from state to state.
MONITOR PRODUCTS, INC.
P.O. BOX 3408
PRINCETON, N.J. 08543
COPYRIGHT © 1989 MONITOR PRODUCTS, INC.,
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising