Dual Exhaust (2014)

Dual Exhaust (2014)
Installation Instructions
1. Make sure the UTV is completely cool before starting the
installation. Make sure the UTV is secure on a level surface
and the wheels are chocked to prevent the unit from rolling.
Remove OEM exhaust cover and brackets. They will not be
re-used.
6. Install TBR muffler assembly to UTV in a sliding motion
using the OEM rubber mounting points.
2. Remove the OEM springs from the muffler joint, muffler
upper mount, and muffler lower mount.
Polaris
Ranger RZR XP1000
7. Attach OEM muffler retaining springs to slip tube joint.
S1R Dual Slip-On
Part # 005-3730409DV
3. Slide the muffler back and to the right side to remove.
8. Re-install OEM retaining springs.
4. Attach TBR mufflers together using the supplied 8x16mm
bolts and lock washers.
9. Re-check hardware after each use.
IMPORTANT - PLEASE READ CAREFULLY
Two Brothers Racing products are intended for closed course
competition purposes only.
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install
this performance part, please consult with your local motorcycle dealer.
Read all instructions first before starting installation. Make sure the
motorcycle and exhaust system are completely cool before starting the
installation. Be sure to save all stock components for possible use later.
**This product has not been tested with all available accessories and
some items may cause excessive heat. Excessive heat may cause
damage to your vehicle. Two Brothers Racing will not be responsible for
damaged parts.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
10. Double check your work and enjoy.
5. Install TBR slip tube. Use a thin layer of supplied antiseize on both slip fit joints. Attach with supplied hook
springs.
Installation Instructions
Polaris
Ranger RZR XP1000
S1R Dual Slip-On
Part # 005-3730409DV
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean using a
mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic of
high quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Qty.
Description
1
Muffler Canister Top 1
Muffler Canister Bottom 1
XP1000 Dual Slip-On Tube 2
8x16mm Socket Head Cap Screw
2
8mm Lock Washer
1
T20 Torx Hex Key
4Springs
1Anti-Seize
1
TBR Sticker Kit
2
USFS Approved Spark Arrestor (installed)
Part Number
005-373-209M2T
005-373-209M2B
005-37304SD
005-SH816
005-WL8
005-9-15820
S-45
P09175
015-10212
005-106S
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters at the first signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers Racing
does not provide a warranty for burned canisters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement