D5-Evo, D10/D10 Turbo Sliding Gate Motor User Guide

D5-Evo, D10/D10 Turbo Sliding Gate Motor User Guide
D5-Evo, D10 and D10 Turbo
User Guide
LIGHTINDUSTRIAL
SLIDING GATE
OPERATOR
page 1
www.CentSys.com
COMPANY PROFILE
Company Profile
1986
In-house
R&D
development
team
100%
testing of
products
1990
1995
1999
Today
Manufacture to
international
quality standard
ISO 9001:2008
After-sales
multi-language
Technical Support
from 07h00 to 18h00
UTC+2
Monday to Friday
Sales and technical support
to Africa, Europe, Asia,
the Americas, Australia
and the Pacific
Centurion Systems (Pty) Ltd reserves the right to make changes to the products described in this
manual without notice and without obligation of Centurion Systems (Pty) Ltd to notify any persons
of any such revisions or changes. Additionally, Centurion Systems (Pty) Ltd makes no representations
or warranties with respect to this manual. No part of this document may be copied, stored in a retrieval
system or transmitted in any form or by any means electronic, mechanical, optical or photographic,
without the express prior written consent of Centurion Systems (Pty) Ltd.
CONTENTS
Contents
SAFETY
FIRST
IMPORTANT SAFETY INSTRUCTIONS
page 6
Introduction page 8
D5-Evo DOMESTIC overview page 9
D10 Turbo overview
page 9
D10 overview
page 10
1. Product Identification
page 11
1.1. D5-Evo DOMESTIC parts identification
page 11
1.2. D10 Turbo and D10 parts identification
page 12
2. D5-Evo DOMESTIC manual Override
page 13
2.1. Disengage the gearbox/drive
page 13
2.2. Re-engage the gearbox/drive
page 13
3. D10 Turbo D10 manual override
page 14
3.1. Disengage the gearbox/drive
page 14
3.2. Manual release latching
page 14
4. Features and functions
page 16
Introduction
page 16
4.1. Gate Operation
page 16
4.1.1. Full Gate Opening
page 16
4.1.2. Modes of Operation
page 17
4.1.2.1. Standard Mode
page 17
4.1.2.2. Reversing Mode
page 17
4.1.2.3 Condominium Mode
page 17
4.1.2.4 PLC Mode
page 18
4.1.2.5 Deadman Mode
page 18
4.1.3. Automatic Closing (Autoclose Mode)
page 18
4.1.3.1. Autoclose Override
page 19
4.1.3.2. Autoclose Advanced Option
page 20
4.1.4. Pedestrian Opening
page 20
4.1.5 Free-exit Opening
page 22
4.1.6. PIRAC Mode (Beam Autoclose) - optional
page 23
www.CentSys.com
CONTENTS
4.1.6.1. Pirac Override
page 24
page 24
4.1.7. Holiday Lockout Mode
4.1.7.1. Emergency stop
page 25
4.1.8. Positive Close Mode
page 25
4.1.9. Operator Run Profiles
page 25
4.1.10. Anti-crushing Sensitivity
page 26
4.1.10.1 Collision Count
page 26
page 27
4.1.11. Safety beams (optional, but recommended feature)
4.1.11.1. Closing Safety Beams
page 27
4.1.11.2. Opening Safety Beams
page 27
4.1.12. Intruder detection alarm (a world first)
page 28
4.1.12.1. Ambush Alarm
page 28
4.1.12.2. Break-in Alarm
page 28
4.1.13. External Gate Status Indication LED
page 29
4.1.14. Courtesy (Pillar) Light Timer (optional feature)
page 30
4.1.14.1. Courtesy (Pillar) Light Control
page 30
4.1.14.2. Courtesy (Pillar) Light act as Warning Light
page 31
4.1.14.3. Pre-open and pre-close delay
page 31
4.1.15. Onboard Multichannel Receiver
page 31
4.1.16. ChronoGuard Timer (a world first)
page 33
4.1.16.1. Some examples of how to use ChronoGuard
4.1.17. Battery Low Protection
page 33
page 34
5. Additional features
page 35
5.1. Battery saver
page 35
5.2. Solar power supply
page 35
5.2.1 D5-Evo DOMESTIC
page 35
5.2.2 D10 Turbo and D10
page 36
5.3 Lightning protection
page 36
6. Basic Maintenance
page 37
7. Diagnostics
page 39
8. Specifications
page 40
9. 24 Month product warranty
page 41
10. Optional extras
page 43
www.CentSys.com
This icon indicates tips and other information that could be useful during the
installation.
This icon denotes variations and other aspects that should be considered during
installation.
This icon indicates warning, caution or attention! Please take special
note of critical aspects that MUST be adhered to in order to prevent
injury.
www.CentSys.com
page 5
ICONS USED IN THIS MANUAL
Icons Used in this Manual
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT
SAFETY INSTRUCTIONS
ATTENTION
To ensure the safety of people and possessions, it is important that you
read all the following instructions.
Incorrect installation or incorrect use of the product could cause
serious harm to people.
The installer, being either professional or DIY, is the last person
on the site who can ensure that the motor is safely installed, and that the
whole system can be operated safely.
CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS before beginning to install
the product.
Even if you have owned and used an automated gate before, we suggest that you
read through the safety instructions below very carefully. Although years of thought
have been put into every CENTURION product – and your safety is our top priority –
accidents do happen. So, please make sure that you fully understand the following safety
requirements before using your automated gate.
Before you attempt to use your new gate operator for the first time, you
should know:
• How to operate the Manual Release thumbwheel
• How the Obstruction Detection System and all other safety features work
• All the safety considerations that come with operating an automated gate – and the
importance of explaining these considerations to everyone who uses the operator
DOs and DON’Ts
• Do not activate your gate opener unless you can see it. Make sure that no people,
pets or any other obstructions are in your gate’s area of travel.
• NO ONE MAY CROSS THE PATH OF A MOVING GATE. Our advanced obstruction
detection technology is designed to stop your gate in its tracks should a child or
pet be in the way. However this is a reactive system and should never supersede
proactive measures of preventing people, pets or vehicles from moving into the path
of a moving gate.
• Check if the obstruction detection system and safety devices for correct operation are
in working order once a month.
SAFETY FIRST
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
page 6
www.CentSys.com
• Keep your gate controls (remote controls) in a safe place. You don’t want anyone
getting in uninvited.
• Look after your gate and it will look after you. Ensure that all working areas are
debris-free and that your automated system is well-maintained and your CENTURION
operator should last you a very long time.
• Ensure that any technician that works on your operator has been trained by Centurion
Systems (Pty) Ltd.
• This product was designed and built strictly for the use indicated in the documentation
provided with the product; any other use, not expressly indicated within the
documentation, could be a source of danger and/or compromise the service life/
operation of the product and invalidate the warranty
IMPORTANT SAFETY INSTRUCTIONS
• Always be mindful of where your limbs are when dealing with moving parts – you
don’t want your fingers to be pinched (or worse).
• Neither Centurion Systems (Pty) Ltd, nor its subsidiary companies, accepts any
liability for damage caused by improper installation or use of the product, or for use
other than that for which the automated system was intended
page 7
SAFETY FIRST
www.CentSys.com
INTRODUCTION
Introduction
This User Guide contains all the information you need to configure and operate your new
D5-Evo DOMESTIC, D10 Turbo or D10 Sliding Gate Operator. From safety instructions
to basic principles of operation and an in-depth description of your CENTURION product’s
many features and functions. By the time you have finished reading this guide you will
have learnt how to make the most out of your gate operator. Even basic maintenance
is covered but, in the unlikely event that your CENTURION product malfunctions, rather
leave it to the professionals and contact your installer or nearest Centurion Systems (Pty)
Ltd Branch (contact details listed on the back page) for prompt assistance.
page 8
www.CentSys.com
D5-Evo overview
The D5-Evo DOMESTIC is driven by a high torque 12V DC motor which can effortlessly
shift gates weighing up to 500kg – perfect for domestic use. The gearbox moulded from a
high-tech engineering polymer not only looks good, but is corrosion-free and guarantees
that even if you live on the coast, your D5-Evo DOMESTIC will just keep on going. For
your security, the internal gearset has a self-locking action so forced entry is no longer an
option for would-be burglars. An optional theft-resistant cage makes intruders’ lives even
more difficult. For your safety, our revolutionary limit switch mechanism monitors the
speed and location of your gate for accurate position control and sensitive anti-crushing
protection.
The D5-Evo DOMESTIC is packed with features and functions, all easily accessible from
a user-friendly LCD controller. Multiple Modes of Operation, alarm functions, an onboard
multichannel receiver, ChronoGuard full seven day timer – you name it, the D5-Evo
DOMESTIC’s got it. The integral 12V 5Ah battery (charged by an internal 220V charger)
comes with full battery back-up and advanced lightning protection so you can always get
in – even when the power is out. It is important to note that the battery is the primary
power source of the D5-Evo DOMESTIC.
You can increase the capacity of the battery with an externally mounted battery to give
longer power failure autonomy.
Instead of the 220V charger, you can have a low voltage charger mounted inside the
D5-Evo DOMESTIC with a plug-in transformer plugged into the nearest plug point inside
the house / building. This saves having to run an electrically compliant 220V supply to
the D5-Evo DOMESTIC.
Finally you can use a solar panel to charge the battery. See section 6.2 (Solar power
supply), for more details about solar charging).
D10 Turbo Overview
The D10 Turbo is perfectly suited for sites with lighter gates requiring a high number
of operations per day and very fast opening and closing speeds, and can operate at
almost double the speed of the standard D10. However, it is not recommended for gates
weighing more than 240kg, as the inertia generated by heavier loads might prove
detrimental to the gearbox at such high speeds.
The gearbox of the D10 Turbo utilises a “true” or “full involute” gear instead of a helical
gear, which means that there is a larger contact area with the worm shaft, ensuring much
greater load bearing capabilities. The standard D10 uses a 34 tooth internal gear and 17
tooth output pinion, whereas the D10 Turbo uses a 22 tooth internal gear and a 20
tooth output pinion.
As with the D5-Evo, the D10/D10 Turbo controller with an LCD interface is a cinch to
set up and it offers an equally impressive list of useful features including CENTURION’s
world first ChronoGuard timer technology. Of course accurate position control, sensitive
anti-crushing and precision stopping power come standard.
www.CentSys.com
page 9
D5-EVO, D10 AND D10 TURBO OVERVIEW
Overviews
D5-EVO, D10 AND D10 TURBO OVERVIEW
D10 Overview
The D10’s 24V DC motor is coupled to the gearbox, resulting in a combination of speed
and power that can push up to a 1 000kg sliding gate no problem – perfect for industrial
sites such as business parks, housing estates and factories. The precision machined, die
cast aluminium gearbox incorporates a self-locking gearset and not only makes short
work of massive gates, but the attempts of prospective criminals too. Add the optional
theft resistant cage and criminals will have to think about a change of occupation. A 24V
7Ah battery supply with a switch mode charger means your batteries are always full,
but if you’re still hungry for power the battery capacity can be increased by using an
externally mounted unit. Similar to the D5-Evo, the D10 batteries can also be charged
by a solar panel instead of a 220V mains supply at the gate.
As with the D5 Evo, the D10 controller with LCD interface is a cinch to set up and it
offers an equally impressive list of useful features including Centurion’s ChronoGuard
timer technology. Of course accurate position control, sensitive anti-crushing and
precision stopping power come standard.
page 10
www.CentSys.com
PRODUCT IDENTIFICATION
1. Product Identification
1.1. D5-Evo DOMESTIC parts identification
1
2
8
9
10
3
4
5
6
11
7
12
FIGURE 1. D5-EVO DOMESTIC GATE MOTOR
7. Foundation plate
2. Courtesy light fuse (3A F/B)
8. Motor fuse (30A ATO)
3. Gate mounted origin Marker
9. 1 x 12V 7.2Ah battery
4. Origin marker bracket
10.1.8A 12V charger
5. Origin sensor
11.Lockable Manual release access door
6. Side covers
12.Encoder sensor (clips into support post)
www.CentSys.com
page 11
SECTION 1
1. D5-Evo DOMESTIC controller
PRODUCT IDENTIFICATION
1.2. D10/ D10 Turbo parts identification
1
2
3
9
10
4
11
5
12
6
7
13
8
SECTION 1
FIGURE 2. D10/ D10 TURBO GATE MOTOR
1. D10/ D10 Turbo controller
8. Foundation plate
2. Courtesy light fuse (3A F/B)
9. Motor fuse (30A ATO)
3. 2 x 12V 7.2Ah battery
10. D10/ D10 Turbo charger
4. Gate mounted origin Marker
11.Manual release handle
5. Origin marker bracket
12. Lock cover
6. Origin sensor (clip under battery)
13.Encoder sensor (clips into support post)
7. Lower cover
page 12
www.CentSys.com
D5-EVO DOMESTIC MANUAL OVERRIDE
2. D5-Evo DOMESTIC Manual Override
2.1. Disengaging the gearbox/drive
Carefully flip to the side the camlock
cover and insert the key and rotate
it 90° clockwise.
While holding onto the key, pull
open the access door to expose the
manual override thumbwheel.
This will allow for the removal of the
cover, as well as for the rotation of
the release thumbwheel.
Rotate the thumbwheel clockwise
until gearbox releases and gate can
be moved manually.
If the gearbox must be left in
manual mode for an extended period
of time for whatever reason, it is
recommended that the access door
is locked. This secures the cover and
prevents access to the inside of the
unit, which could contain high
voltages. It also prevents theft of
any components and provides full
protection from the elements.
FIGURE 3
Do not remove the
thumbwheel. Removal
of the thumbwheel may
result in water entering
the gearbox and the
warranty will be void
2.2. Re-engaging the gearbox/drive
Rotate thumbwheel anticlockwise
until thumbwheel feels loose in the
hand. Make sure that the manual
override access door can be closed.
FIGURE 4
www.CentSys.com
page 13
SECTION 2
Slide gate until gearbox/drive
engages. Never run the motor before
the unit is engaged.
D10/ D10 TURBO MANUAL OVERRIDE
3. D10/ D10 Turbo Manual Override
3.1. Disengaging the gearbox/drive
Flip down the lock cover and Insert
the camlock key and rotate it 90°
clockwise.
FIGURE 5
Pull down the manual release handle
to override the gearbox and allow it
to be moved manually.
Reverse the process to re-engage
the gearbox/drive.
FIGURE 6
3.2. Manual release latching
If the gearbox must be left in manual mode for an extended period of time for whatever
reason, it is recommended that the manual release is latched, the handle raised back into
its normal position and locked, locking the cover in place at the same time. This prevents
access to the inside of the unit, which contains high voltages and prevents theft of any
components and provides full protection from the elements.
SECTION 3
With the manual release handle pulled down, follow the process below to latch the
manual release.
page 14
www.CentSys.com
D10/ D10 TURBO MANUAL OVERRIDE
Insert the split pin (supplied with the
mounting hardware kit), through the
hole in the gearbox as indicated
Split pin
FIGURE 7
Make sure the split pin goes all the
way through as shown
Split pin
FIGURE 8
Raise the handle and lock
Remove the key and fold back the
lock cover
www.CentSys.com
page 15
SECTION 3
FIGURE 9
FEATURES AND FUNCTIONS
4. Features and Functions
Introduction
The D5-Evo DOMESTIC and D10 sliding gate operators’ advanced functions are controlled
by intelligent micro-controller based electronic controllers.
An intuitive LCD (Liquid Crystal Display) controller with a user-friendly menu allows for
quick and easy set-up and the ability to change functions at the touch of a button and
displays useful diagnostics.
FIGURE 10. CONTROLLER LCD DISPLAY
4.1. Gate Operation
4.1.1. Full Gate Opening
SECTION 4
The CENTURION remote controls
that operate with the onboard
receivers of the D5-Evo
DOMESTIC, D10 and D10 Turbo
sliding gate operators are used to
operate the gate. However, most
automatic gate installations are
also fitted with an intercom, which
provides for communication between
the house / building and the gate.
The handset is usually fitted with
a gate / door release pushbutton,
which when pressed, will operate the
gate.
FIGURE 11
page 16
www.CentSys.com
To operate the gate to open fully, the D5-Evo DOMESTIC, D10 and D10 Turbo have
a number of operating modes to choose from depending on the application. Only one
mode can be selected at any given time, unless indicated otherwise.
4.1.2.1. Standard Mode
Standard Mode is the most commonly used mode for domestic applications as it allows
full control of the gate. Press the button of the remote control or the gate / door release
pushbutton on the intercom for approximately one second to get the gate in motion.
FEATURES AND FUNCTIONS
4.1.2. Modes of Operation
If you press the button again, while the gate is moving, the gate will stop. Press the
button for a third time and the gate will go into reverse.
Autoclose and PIRAC (Beam Autoclose) can be used with Standard
Mode. An infrared safety beam needs to be installed across the gate
entrance and connected to the Closing Safety Beam input on the D5-Evo
DOMESTIC or D10/D10 Turbo to use this function, in order to prevent
the gate from closing on people, pets or vehicles.
4.1.2.2. Reversing Mode
Reversing Mode offers slightly more security than Standard Mode as it allows you to close
your gate quickly by pressing, for instance, your remote control just as you drive through
the gate to prevent children or pets running out - or anybody getting in behind you.
When pressing the button of the remote control or the gate / door release pushbutton on
the intercom, your gate will be set in motion. If you press the button again, the gate will
move in the opposite direction. So, if the gate is opening and you press the button, the
gate will stop and immediately start to close (and vice versa)
Autoclose and PIRAC (Beam Autoclose) can be used with Reversing
Mode. An infrared safety beam needs to be installed across the gate
entrance and connected to the Closing Safety Beam input on the D5-Evo
DOMESTIC or D10/D10 Turbo to use this function, in order to prevent
the gate from closing on people, pets or vehicles.
4.1.2.3. Condominium Mode
www.CentSys.com
page 17
SECTION 4
This mode is ideal for increased safety and security in multi-user applications such as
townhouses, estates, factories or office parks. If you select Condominium Mode, your
gate will open when pressing the button of the remote control or the gate / door release
pushbutton on the intercom – but pressing the button again while gate is opening will
be ignored. It will not cause the gate to stop or to reverse. Only the internal Autoclose
described on page 11 of this User Guide, which is automatically enabled, will close the
gate. If the button of the remote control or intercom gate release is pressed while the
gate is closing, the gate will immediately reopen. The gate cannot be stopped in a
midway position and will therefore always close. If the button is pressed while the gate is
in the open position, the Autoclose timer is reset. Finally, the Autoclose Override feature
described on page 11.
FEATURES AND FUNCTIONS
We highly recommend that you use Infrared Safety Beams if you select
Condominium Mode in order to prevent the gate from closing on people,
pets or vehicles.
PIRAC (Passive Infrared Beam Autoclose) can be used with Condominium Mode.
4.1.2.4. PLC Mode
This highly specialised mode is suited to industrial applications where a separate
computer or programmable logic controller (PLC) is used to operate the gate. Three
separate inputs are used to open, stop or close the gate:
• Free-exit input (a trigger from the PLC will only open the gate)
• Holiday Lockout input (a trigger from the PLC will stop the gate)
• Trigger input (a trigger will only close the gate)
Autoclose and PIRAC (Beam Autoclose) cannot be used with PLC Mode
4.1.2.5. Deadman Control Mode
A variation of PLC Mode, Deadman Control Mode requires a pushbutton to be held in
order for the gate to be set in motion. If the button is released, the gate will immediately
stop.
Alternatively, an emergency stop pushbutton can be used to permanently hold the gate in
“Stop Mode”. Releasing the pushbutton will allow your gate to open or close.
If the open or closed triggers are held when the gate reaches the end of its cycle either
fully open or fully closed, the internal end-oftravel limit switch system will shut off the
motor and prevent further operation in the respective direction.
Autoclose and PIRAC (Beam Autoclose) cannot be used with Deadman Control
Mode
4.1.3. Automatic closing (Autoclose Mode)
SECTION 4
The D5-Evo DOMESTIC and the D10 sliding gate operators have the facility to
automatically close the gate after it has opened. When enabling this feature, the time
that the gate stays open is by default fifteen seconds (this time is adjustable1).
As described in the previous section Autoclose is selectable with Standard and Reversing
Modes and by default the function is off. However, Autoclose is automatically enabled in
Condominium Mode.
1. It is possible to adjust the delay before the gate closes in one second increments from zero seconds to four minutes. The default time is five seconds.
page 18
www.CentSys.com
Automatic closing can be overridden in Standard and Reversing Modes by pressing and
holding the button of the remote control or intercom gate release for no less than three
seconds. The gate response will be to start opening and then to stop as soon as the
Autoclose Override feature is activated. On releasing the button, the gate will continue
opening until fully open.
Your gate will stay open until you use the remote control or intercom gate release to
close the gate. The D5-Evo DOMESTIC, the D10 and the D10 Turbo will then revert to
normal Autoclose operation
FEATURES AND FUNCTIONS
4.1.3.1. Autoclose Override
The Autoclose function cannot be overridden in Condominium Mode.
1
Press and hold remote control pushbutton;
gate will start to open
2
It is possible to adjust the
override time or the time
required to hold down the
button in order to override
Autoclose in one second
increments from one to
ten seconds. The default
time is three seconds.
Gate stops to indicate that Autoclose
Override has been engaged
3
FIGURE 12
www.CentSys.com
page 19
SECTION 4
Release pushbutton; gate will continue
to open fully and stay open
FEATURES AND FUNCTIONS
4.1.3.2. Autoclose Advanced Options
You can also independently set Autoclose to function when the gate is partly open, fully
open or partly closed.
For example, disable Autoclose when the gate is partly closed to allow construction
workers, gardeners, etc access to your property (although this comes with security
risks). By enabling the Autoclose in all states of gate movement, ensures that the
gate can never be left in any position other than fully closed. The default setting when
enabling Advanced Autoclose is partly open and fully open, but not partly closed.
4.1.4. Pedestrian Opening
The Pedestrian Opening input opens
the gate just wide enough for a
pedestrian to pass through the
opening. A second button on your
remote control can be used to
operate the Pedestrian Opening
function.
You can also set a keyswitch or
keypad mounted adjacent the gate
entrance to operate this function.
There is a two second delay (default,
but adjustable) before the gate
opens to warn the pedestrian that
the gate is about to move.
FIGURE 13
SECTION 4
It is highly recommended
that access control
devices are placed in
such a position that
people do not need to
reach through the gate in
order to operate them in
order to prevent possible
injury in the event that
the gate moves.
FIGURE 14
page 20
www.CentSys.com
The gate can be kept open by keeping a trigger on the input (keeping your key in
the keyswitch, for example) – once removed the gate will close after the default, but
adjustable, five seconds.
FEATURES AND FUNCTIONS
If the Courtesy Light (Page 20) is connected to the control card, it will flash
indicating that the gate will open a default distance of approximately one metre
(adjustable). The gate will close after a default time of five seconds (adjustable).
The Pedestrian Opening Input is fully configurable and can be set to suit your needs.
You can adjust the pre-opening time delay; the amount that the gate opens; and the
pedestrian autoclose delay using your LCD controller.
If a Safety Beam is fitted and the beam is broken while the gate is closing, the gate will
stop and open to the pedestrian position. The gate will remain open while the beam is
broken and the five second (adjustable) Autoclose delay will only commence once the
beam has been cleared.
• For safety reasons it is recommended that all pedestrian keyswitches
and keypads are installed on the opposite end of the gate to where
the operator is installed
• It is possible to adjust the delay before the gate opens in one second
increments from zero to 65 seconds (one minute and five seconds).
The default time is two seconds
• It is possible to adjust the width of the pedestrian opening from a minimum
of 50 millimetres to the full gate opening in ten millimetre increments.
The default opening is one metre
• It is possible to adjust the delay before the gate closes in one second
increments from zero to 65 seconds (one minute and five seconds).
The default time is five seconds
page 21
SECTION 4
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.5. Free-exit Opening
The Free-exit Opening allows
visitors to exit townhouses, estates,
factories or office parks easily.
An inductive ground loop is mounted
under the driveway inside the
property a short distance away from
the gate. The output of the inductive
ground loop detector is connected to
the free-exit input on the controller.
Vehicle drives over
free-exit inductive loop
When a vehicle drives over the loop,
a detector senses the metal in the
vehicle and activates the free-exit
function which opens the gate.
The ground loop cannot be activated
by a person or any nonmetallic
objects and can be set to only
activate if it detects a large amount
of metal.
Gate
FIGURE 15
Free-exit never initiates a closing
cycle so the Autoclose function must
be enabled in order for the gate to
close.
If the gate is already open or
opening, triggering the free-exit
input will have no effect other than
to reset the Autoclose timer. If the
gate is closing, triggering the freeexit input will immediately stop and
re-open the gate.
Free-exit
inductive loop
Free-exit facility activates gate to open
An infrared beam can be used
instead of an inductive ground loop,
but the beam will be activated if
a person (or any object) moves
through it, so this option is typically
less secure.
FIGURE 16
SECTION 4
Please contact Centurion Systems (Pty) Ltd for more information on whether a ground
loop or infrared beam is better suited to your needs.
page 22
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.6. PIRAC Mode (Beam Autoclose Mode) - Optional
This mode can only be used if a Closing Safety Beam is fitted.
This mode can be used in
conjunction with any of the
operating modes - Standard,
Condominium and Reversing Mode.
Gate opening
With PIRAC Mode enabled, your gate
will close as soon as you have driven
through and passed the Closing
Safety Beam – giving intruders no
time to follow behind you.
If Autoclose is enabled and the
gate has been opened but nothing
moves through the Closing Safety
Beam, the gate will stay fully open
for the duration of the Autoclose
timer before closing. However,
if something passes through the
Closing Safety Beam the gate will
close immediately.
Beam
FIGURE 17
Gate opening
If something crosses the beam
while the gate is opening, it will
continue to open until the beam
is cleared and the gate will then
stop and close. If the gate has
reached its fully open position, it
would stop and remain open
until the beam is cleared.
Beam broken
FIGURE 18
Gate
closing
PIRAC mode’s ‘stop on opening’
configuration will open the gate
a short, adjustable distance past
the point at which the beam was
broken and stop, wait for the
beam to be re-made or the
Autoclose timer to expire, then
close.
Beam re-made
FIGURE 19
page 23
SECTION 4
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.6.1 PIRAC Override
The PIRAC (Beam Autoclose Mode) can be overridden in Standard and Reversing Modes.
Similar to overriding the Autoclose function you must press and hold the button of the
remote control or intercom gate release for at least six seconds. The gate response will
be to start opening and then to stop for a pause time of three seconds and then continue
to open as soon as the PIRAC Override feature is activated. Once the gate resumes
opening you may release the remote control button or intercom gate release and the
gate will continue to the fully open position with PIRAC Mode overridden.
Your gate will stay open until you use the remote control or intercom gate release to
close the gate. The D5-Evo DOMESTIC, D10 and the D10 Turbo will then revert to normal
PIRAC operation.
4.1.7. Holiday Lockout Mode
This feature completely immobilises
the operator and deactivates all
inputs so nobody can get into your
property while you are away.
One of the buttons on your remote
control can be used to switch the
Holiday Lockout Mode as well as a
latching keyswitch or keypad
mounted adjacent the gate entrance,
accessible from the outside of the
property.
When Holiday Lockout Mode is
enabled, any of the access control
devices that are connected to the
D5-Evo DOMESTIC, D10 and the
D10 Turbo, will be inactive and not
even tampering with the keyswitch,
keypad or access tag readers on the
outside of the property, will open
the gate – particularly useful if you
intend leaving your property
unattended for extended periods
of time.
Gate electronically locked
FIGURE 20
SECTION 4
If Holiday Lockout Mode is enabled while the gate is moving or in the open position, it will
only activate when the gate is back in the closed position.
If somebody tries to open the gate via a valid access control device, such as a
remote control, etc. with Holiday Lockout Mode enabled, the onboard buzzer will
beep periodically for 30 seconds to confirm that the gate operation has been
disabled using this feature.
page 24
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.7.1 Emergency Stop
The Holiday Lockout function can
also be used as an Emergency Stop
function. Mount an emergency stop
pushbutton in a weatherproof
housing near the gate and you can
bring your gate to an immediate
stop with just one press. The
emergency stop button must
be reset before the gate can be
operated again.
FIGURE 21
• Emergency Stop will override normal Holiday Lockout Mode functions
• If somebody tries to open the gate via a valid access control device, such
as a remote control, etc. with Holiday Lockout Mode enabled, the onboard
buzzer will beep periodically for 30 seconds to confirm that the gate
operation has been disabled using this feature.
• The emergency stop is typically used at a manned entrance so that security
is not compromised with a would-be intruder possibly gaining access to
the stop button. In a domestic situation you can set up one of your remote
pushbuttons to operate the emergency stop without compromising your
security
4.1.8. Positive Close Mode
Positive Close Mode is intended for applications where the gate must close fully against
the gate end post for security reasons – such as ensuring proper contact of the switch on
the gate that feeds power to the electric fence.
This feature operates only during the last few millimetres when the gate closes.
It is recommended that a rubber strip be fixed to the front edge of the gate to
cut down the noise when the gate closes against the end post.
4.1.9. Operator Run Profiles
The D5-Evo DOMESTIC, D10 and the D10 Turbo can be customised to your
exact requirements using your LCD controller. The open and closing speeds can be
independently set. Even the ramp up to full speed, ramp down to close speed and crawl
distance before the gate stops can be adjusted. Please contact Centurion Systems (Pty)
Ltd for more information on finding the configuration that is best for you.
page 25
SECTION 4
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.10. Anti-crushing Sensitivity
The D5-Evo DOMESTIC, D10 and the
D10 Turbo incorporate a sensitive
electronic anticrushing technology
that activates if a person or vehicle
obstructs your gate.
The operator will respond differently
to obstructions depending on the
Operating Standard (e.g. CE, UL325)
you select. The typical response for
an opening gate is to immediately
stop and a closing gate will stop then
immediately reopen.
Collision force can be set
independently per direction of travel
and can be set from minimum to
maximum in five incremental steps.
A sixth incremental step will disable
collision sensing entirely and allow
for maximum force – the motor will
run until it stalls at which point a
collision will be detected.
Gate closes, hits obstruction, stops and closes
immediately
FIGURE 22
Step six should only
be used if additional
safety measures such
as Infrared beams and
sensitive edges are
present.
4.1.10.1. Collision Count
SECTION 4
A counter monitors the number
of collisions the gate experiences
before it fully closes. If the number
exceeds the default value of four,
which can be adjusted in the Multiple
Collisions Counter, the controller will
shut down. The Status LED will flash
four times every second until a valid
trigger is received.
Gate opens,
hits obstruction and stops
FIGURE 23
Please refer to Gate Status
Indication for more information on
this diagnostic device.
page 26
www.CentSys.com
4.1.11.1. Closing Safety Beams
Closing Safety Beams provide
additional protection against your
gate closing on people, pets or
vehicles.
FEATURES AND FUNCTIONS
4.1.11. Infrared Safety Beam (optional but recommended)
If the closing beam is broken while
the gate is opening, it will continue
to open. If the gate is open, the gate
cannot be closed and if the gate is
closing, it will stop and reopen.
If you select the Autoclose feature,
the gate will remain open if the
beam is broken and only close after
the set Autoclose time has expired
when the beam has cleared.
You can use other protection devices
like an inductive ground loop instead
of an infrared beam, but loops are
only sensitive to the presence of a
vehicle (large metal objects) and
provide no protection to people or
other objects in the path of the gate.
Please contact Centurion Systems
(Pty) Ltd for more information on
suitable protection devices.
Gate open – gate cannot close
Gate closing – gate stops and reopens
Gate opening – gate continues opening
FIGURE 24
4.1.11.2. Opening Safety Beams
These beams prevent your gate from
opening if an object or person is in
the way.
If the beams are broken while the
gate is closed, the gate will not
open. If the gate is opening, it will
stop then close. If the gate is
closing, it will continue to close.
Gate closed – gate cannot open
Gate opening – gate stops and re-closes
Gate closing – gate continues closing
FIGURE 25
www.CentSys.com
page 27
SECTION 4
Please contact Centurion Systems
(Pty) Ltd for more information on
suitable protection devices.
FEATURES AND FUNCTIONS
4.1.12. Intruder-detection Alarms1 (a world first)
4.1.12.1. Ambush Alarm
Once activated, if the opening or
closing beams are continuously
interrupted for a predefined time,
the Ambush Alarm will sound.
Intruders often cover beams’ lenses,
thus breaking the beam, so your
gate stays open after you have
entered or left your property – but
with the Ambush Alarm enabled
you can be instantly alerted of any
criminal activity.
4.1.12.2. Break-In Alarm
If the closing beam on the outside of
your property is broken, the BreakIn Alarm will sound and continue
until 30 seconds have passed since
the beam is re-made.
Intruder masks safety beams,
30 seconds later
alarm is activated
FIGURE 26
Intruders will not be able to loiter
outside your property as the BreakIn Alarm will immediately alert you
of their presence – and the noise
of the onboard buzzer is often an
effective deterrent. Optionally the
alarm signal can be routed to an
armed response company.
If the Ambush Alarm or Break-In
Alarm is utilised, the system may be
configured to operate one of the
following outputs provided on the
controller:
• Onboard buzzer –
emits a continuous tone
Intruder breaks safety
beam while loitering
at gate, alarm immediately
activated for 30 seconds
Alarm
Safety beam
FIGURE 27
• Pillar / Courtesy light contact
• Safety beam common
SECTION 4
• Status LED output
• Auxiliary IO (which can be used to connect to a third party alarm and security
company, or a CENTURION G-Switch device to alert you of the alarm via SMS)
It is typical to select only one of the alarm features.
1. Requires infrared gate safety beams to be installed
page 28
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.13. External Gate Status Indication
A LED (Light Emitting Diode)
mounted on your intercom allows
you to view the position of your gate
and the condition of the battery and
power supply from the safety of your
home. The different signals of the
LED are described below:
FIGURE 28
LED Signal
Diagnosis
Off
Gate is closed
On
Gate is partially or fully open
Continuous slow flash
Gate is opening
Continuous fast flash
Gate is closing
Courtesy (Pillar) lights on
One flash every two seconds
No mains present
Two flashes every two seconds
Battery voltage is low
Three flashes every two seconds
Multiple collisions have occurred
Four flashes every two seconds
If you choose not to fit a Gate Status Indicator, the Status LED on the Controller
can also be used for troubleshooting.
page 29
SECTION 4
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.14. Courtesy (Pillar) Light Timer
(optional feature)
Courtesy (Pillar) Lights can be
connected through the controller
if a 220V power supply is available
at the gate. The lights will switch
on every time the gate is given a
signal to operate and stay on for an
adjustable period of one second to
ten minutes (in increments of one
second) then automatically turn off.
FIGURE 29
The purpose is to bathe your entrance with light when you open the gates and increase
your security as you drive into your property – it also saves electricity as the lights only
come on when you use the gate motor.
Using the Pedestrian Opening feature will cause the Courtesy (Pillar) Lights to
flash three times before the gate opens. This is a safety feature to protect the
pedestrian.
4.1.14.1. Courtesy (Pillar) Light Control
The Courtesy (Pillar) Lights can be switched on from inside your home or office by
connecting a pushbutton to the D5-Evo DOMESTIC, D10 or D10 Turbo controller.
For your safety this pushbutton switches only low-voltage signals. Press and release the
button for the lights to switch on for the defined period then switch off automatically.
Press and hold the button for three to four seconds for the lights to stay on permanently,
until you push the button again. If the Gate Status Indicator is fitted to the intercom
handset, the LED will flash once every two seconds to indicate that the lights are on
permanently.
This feature can also be operated using your remote control. Simply set one of the spare
buttons on the transmitter to switch your Courtesy (Pillar) Lights on and off.
SECTION 4
Please refer to Onboard Multichannel Receiver for more information on the various
functions you can operate with your remote control.
Low-wattage, 12V DC light fittings are also readily available and can be connected to the
system, drawing power directly from the battery. However, please ensure that the power
drawn by the lights and motor does not exceed the recharge rate of the battery.
Larger charger units can be fitted to cope with the additional load – contact your gate
automation specialist or Centurion Systems (Pty) Ltd for more information.
page 30
www.CentSys.com
FEATURES AND FUNCTIONS
4.1.14.2. Courtesy (Pillar) Light acts as Warning Light
For additional safety, the Courtesy
(Pillar) Light output can be
configured to act as a Warning Light
before the gate operates and while
the gate is moving.
Contact your gate automation
specialist or Centurion Systems (Pty)
Ltd for more details on the different
Warning Light Modes.
FIGURE 30
4.1.14.3. Pre-open and Pre-close Delays
If you make use of the Warning Light feature, you can set your gate to have a slight
delay before it opens or closes to allow the light to warn pedestrians or vehicles that the
gate is about to move.
The Pre-open and Pre-close Delays can be independently set and can also be used
independently of the Warning Light feature referred to above.
4.1.15. Onboard Multichannel Receiver
The D5-Evo DOMESTIC, D10 and
D10 Turbo controllers are supplied
standard with a multichannel
receiver compatible with
CENTURION’s secure rolling code
(KeeloqTM encryption). The receiver
will allow any combination of the
different inputs (such as Trigger,
Pedestrian, Holiday Lockout, etc.)
to be operated from a single multibutton remote control.
FIGURE 31
www.CentSys.com
page 31
SECTION 4
You can artificially increase the number of buttons of a CENTURION multi-button remote
control by using a two button combination. One of the buttons is used as a shift button
to allow the other buttons to be used again in combination with this button. Press and
hold the shift button and then press one of the other buttons to create a new button.
The shift button cannot be used as a button on its own; it must always be used in
combination with another button.
FEATURES AND FUNCTIONS
Use of the shift key principle allows
a three button transmitter to gain
an extra button and operate four
functions and a four button
transmitter gains two extra buttons
and can operate six functions.
This is quite handy if you’d like to
control additional devices from a
single multi-button remote control,
for example, your garage doors if
they are equipped with CENTURION
rolling code receivers.
1
2
Shift key
3
5
4
6
However it’s also important to note
that other devices cannot be
activated with the new shift button,
only the D5-Evo DOMESTIC, D10
and D10 Turbo (and other
CENTURION operators that are
equipped with an onboard receiver)
are able to recognise the shift button
signals.
Shift key
Press and hold the
‘fourth’ button as a
Shift Button
together with
button 1, 2 or 3 to
operate 4, 5 or 6
FIGURE 32
Using a shift button also prevents you from enabling functions like Holiday Lockout Mode
by accident because you have to use both hands to press the two button combination.
Another function provided with this receiver is the ability to record the memory location
of each remote control, mapping this to the name of the owner of the remote
(if recorded). This allows any transmitter that is lost or stolen to be selectively erased
from the system without affecting any of the other remotes installed.
It is also possible to erase the functions of certain buttons on a remote control if they’re
no longer required. Alternatively, the functionality of certain buttons can be changed to
trigger different functions.
At any stage remote controls can be selectively added, deleted or edited within the
system.
SECTION 4
Contact your gate automation specialist or Centurion Systems (Pty) Ltd for assistance.
page 32
www.CentSys.com
ChronoGuard™ (a world first) is a powerful multichannel timer feature which has been
added to the D5-Evo DOMESTIC, D10 and D10 Turbo controllers. A Real Time Clock
and Calendar (RTC) lets you set the following features to operate automatically or be
prevented from operating (time-barred) during any Time-period you choose:
• Trigger (TRG) (auto activation and time-bar1)
FEATURES AND FUNCTIONS
4.1.16. ChronoGuard Timer (a world first)
• Free-exit (FRX) (auto activation and time-bar1)
• Pedestrian opening (PED) (auto activation and time-bar1)
• Holiday Lockout (LCK) (auto activation and time-bar1)
• Closing Beam (IRBC) (auto activation only)
• Courtesy (Pillar) Light control (AUX) (auto activation and time-bar1)
• Courtesy (Pillar) Light relay (time-bar only1)
• Auxiliary output2 (auto activation and time-bar)
A Time-period can be a once off event, or can be set to repeat on a weekly or annual
basis. The weekly repeat can be chosen to occur on every day of the week, weekdays
only, weekends only, or any specific day. The minimum duration of a time-period is one
minute – and you can set 100 different Time-periods. The “Tp” icon will appear on the
display to indicate that a time-period is active.
You can even set up different conditions by combining Time-periods as well as set up
exclusions (once off time periods when the auto activation or time-bar period must be
ignored) so your gate will automatically open at certain times on weekdays, but will know
not to open on a public holiday.
1. It is possible to time-bar the operation of the device physically wired to this feature and/or the same feature controlled via the radio receiver.
2. Spare output, which via a relay board can drive a variety of external devices such as sprinkler system, fountain etc.
4.1.16.1. Some examples of how to use ChronoGuard:
Pillar / Courtesy Lights could be set
to switch on at 20:00 in combination
with Holiday Lockout Mode so your
driveway would be lit up and locked
down to keep you safe at night.
www.CentSys.com
page 33
SECTION 4
FIGURE 33
FEATURES AND FUNCTIONS
Time-bar prevents something from
switching on or being activated –
so use it to turn off functions like
Courtesy / Pillar Lights to save
electricity during the day.
Or de-activate the freeexit loop at
the exit to your premises after hours
and over weekends.
FIGURE 34
Time-bar can also be used to limit access. For example, your staff can get in on
weekdays – but will be locked out over the weekend or on public holidays for added
security. However, there is only one group that can be set up per input. So, if you want
your gardener’s remote to be time-barred for a certain period and your maid’s to be
barred for a different time-period, you’ll have to set the gardener’s remote to open using
one input (like the operator) and the maid’s remote to trigger another input
(like the keyswitch).
If your factory is particularly busy
during certain hours of the day from
Monday to Friday, set your operator
to keep the gates open during these
times to allow for quick traffic flow.
During any other hour, or over the
weekend or public holidays, you’ll
have to use your CENTURION access
control device (keypad, proximity
reader etc) to get in.
Hold open
FIGURE 35
4.1.17. Battery Low Protection
In the event of a power failure, energy is drawn from the battery but not replaced.
Battery Low Protection will shut off the gate system to prevent running the battery flat
when the battery voltage drops below:
•D5-Evo DOMESTIC – 10.5 volts
•D10/D10 Turbo – 21 volts
SECTION 4
The Gate Status Indication LED will flash three times every two seconds and the
controller LCD will state “Battery Low”.
The gate will complete its current cycle, close and then shut down until the battery
voltage has recovered.
If you see the Battery Low signal, check that the power circuit feeding the gate motor
is switched on otherwise contact your gate automation specialist or Centurion Systems
(Pty) Ltd for assistance.
page 34
www.CentSys.com
ADDITIONAL FEATURES
5. Additional Features
5.1. Battery saver
In the event of a Battery Low
shutdown, only the motor will stop
drawing current – the controller,
infrared beams and any other
peripheral device will continue to
draw power and flatten the battery,
however, at a much slower rate.
An optional low cut-out switch
(product code CP1071) totally
disconnects the battery and protects
it from being fully discharged and
potentially damaged.
FIGURE 36
Contact your gate automation specialist or Centurion Systems (Pty) Ltd for further
details.
1. Currently only available for the D5-Evo not the D10/D10 Turbo
5.2. Solar Power Supply
5.2.1. D5-Evo DOMESTIC
A solar panel can be used to
charge the battery instead of the
conventional charging circuit. A
20 Watt panel will provide enough
power for 20 operations (less if 12V
DC security lights are fitted) of
an average gate.
FIGURE 37
You will need to fit a deep-cycle low-maintenance battery (minimum 35Ah) in order to
provide sufficient back-up capacity during days of poor weather.
The charger supplied with the standard D5-Evo DOMESTIC system must also be replaced
with a high efficiency solar regulator.
www.CentSys.com
page 35
SECTION 5
These are typical values for Southern Africa. Contact Centurion Systems (Pty) Ltd or your
gate automation specialist for details on what solar panel to select in your area.
ADDITIONAL FEATURES
5.2.2. D10 and D10 Turbo
It is possible to adapt in the D10 as well as D10 Turbo for solar charging; however,
typically 2 x 20W panels wired in series with the 24V battery supply will be required.
Contact Centurion Systems (Pty) Ltd or your gate automation specialist for more details.
5.3. Lightning Protection
The D5-Evo DOMESTIC, D10 and D10 Turbo controllers come standard with on-board
lightning protection – but please make sure that an adequate earth is installed for this to
function properly.
Please contact Centurion Systems (Pty) Ltd for more information.
SECTION 5
Lightning damage is not covered under the normal warranty of the equipment.
page 36
www.CentSys.com
Motors from Centurion Systems (Pty) Ltd are designed to be maintenance-free.
However, there are some basic checks that should be carried out regularly (every six
months). These checks will increase the long-term reliability of the system and prevent
erratic operation of your gate.
BASIC MAINTENANCE
6. Basic Maintenance
Isolate Mains supply and disconnect the battery before cleaning or
working on the system.
6.1. General Maintenance
1. Keep the track clear of stones, dirt and obstructions
2. Ensure that all rollers run freely
3. Put the operator into Manual Mode and check that the gate runs freely on its rail and
does not catch or foul against the walls or pillars
4. Ensure that the gate wheels and guide-rollers are rotating freely and are not worn.
In high-volume applications it will be necessary to replace these components regularly
5. Ensure that the rack is properly secured to the gate and that it does not press down
onto the operator pinion at any point along its travel
6. Keep shrubs and vegetation clear of the motor and rack
7. Check that the key still operates the camlock - spray with lubrication if necessary
8. Keep the inside of the motor housing clear of insects and dust
6.2. Battery
CENTURION operators, which are fitted with maintenance free lead acid batteries, should
provide at least three years of normal service life.
For sites utilising an external large capacity (+/-35Ah) low maintenance battery, ensure
that the level of liquid (electrolyte level) is correct.
In all instances check for corrosion of the battery terminals.
Clean and apply copper-based grease as necessary.
6.3. Charger
The D5-Evo DOMESTIC, D10 and D10 Turbo operators have chargers separate to the
main controller. In the case of product malfunction, the charger fuse should be checked,
but only by a qualified electrician.
Always isolate the mains supply to the operator before attempting to remove and check
the fuse.
www.CentSys.com
page 37
SECTION 6
Check the “Mains Present” icon on the main diagnostic screen or switch to the
battery charger diagnostic screen and check the charger voltage – right hand
value. This should indicate, 13.8V for the D5-Evo DOMESTIC and 27.6V for
the D10 and D10 Turbo. Each charger has a red light (LED) to indicate mains
supply.
BASIC MAINTETANCE
Do not attempt to repair the unit yourself. Any work performed by
unauthorised personnel may void the warranty.
6.4. Gearbox Oil Level
SECTION 6
Gearbox Oil Level Check the oil level as described in the Lubrication section of the
Installation Manual. Should the installation manual be unavailable, please refer to the
online manuals on our website, www.centsys.co.za. Alternatively, contact Centurion
Systems (Pty) Ltd or your gate automation specialist for assistance.
page 38
www.CentSys.com
Depending on the type of fault or condition of the motor, audible feedback will be given
via the onboard buzzer. Listen out for this and refer to the table below:
DIAGNOSTICS
7. Diagnostics
The different conditions are given in order of precedence.
Break-in Alarm – if the safety beams have been broken with this feature set, the
buzzer will emit a continuous tone for 30 seconds.
Ambush Alarm – if the safety beams have been broken with this feature set, the
buzzer will emit a continuous tone until the safety beams have been cleared.
Battery Low – Buzzer will emit three beeps every two seconds for 30 seconds. Refer
to section, Battery Low
Multiple collision – Buzzer will beep periodically until condition is cleared. Refer to
section, Anti-crushing, collision count
Holiday Lockout – If the Holiday Lockout has been enabled, when triggering
to operate the gate, the gate will not operate but the buzzer will emit one beep
periodically for 30 seconds
Emergency Stop – If the Emergency stop button has been activated, the buzzer will
emit buzzer will emit one beep periodically for 30 seconds
Time-barring - if a time-barred input or remote control is operated during a timebarring period, in addition to the gate not reacting to the input being activated or the
remote control, the buzzer will emit one beep periodically for 30 seconds
Mains failure – If the mains supply to the charger has failed the buzzer will emit two
beeps every two seconds for 30 seconds
Safety beam broken – if something in the path of the beams the buzzer will emit
one beep periodically for 30 seconds
Safety beam failure – if the safety beams are not operating the buzzer will emit five
beeps periodically for 30 seconds (beams test circuit must be enabled)
Contact Centurion Systems (Pty) Ltd or your gate automation specialist for assistance.
Do not attempt to repair the unit yourself. Any work performed by
unauthorised personnel may void the warranty.
page 39
SECTION 7
www.CentSys.com
TECHNICAL SPECIFICATIONS
8. Technical Specifications
Technical data
Input voltage
Motor voltage
D5 - Evo
D10
D10 Turbo
220V AC +/-10%
50Hz1
220V AC +/-10%
50Hz1
220V AC +/-10%
50Hz1
12V DC
24V DC
24V DC
Battery driven2 –
1.8A charger
Battery Driven2 –
2.0A charger
Battery Driven2 –
2.0A charger
Push force - rated
17kgf
30kgf
15kgf
Gate speed
(varies with load)
18 - 22m/min
22 - 26m/min
40 - 50m/min
50%3,4
45%3,4
25%3,4
Daily operations –
max
263
7503,6
7503,6
Gate mass - max
500kg
Onboard receiver
specification
Code-hopping
multichannel
433MHz,
Capacity - 500
transmitter
buttons
Motor power supply
Duty cyle mains present
1000kg
5
240kg
Code-hopping
multichannel
433MHz,
Capacity - 500
transmitter
buttons
5
Code-hopping5
multichannel
433MHz,
Capacity - 500
transmitter
buttons
TABLE 1
SECTION 8
1: Can operate off a solar supply, consult Centurion for assistance
2: 5Ah battery (can be upgraded for longer power failure autonomy)
3: Based on a push force of less than 50% of rated
4: Based on 25oC ambient temperature and unit not in direct sunlight
5: KeeloqTM encryption
6: With brush replacement interval of two years
page 40
www.CentSys.com
You can register your product(s) online at www.CentSys.com, which will assist
you in keeping a record of your date of purchase or installation, serial numbers,
etc.
All of our products are manufactured with extreme care, thoroughly inspected and tested.
The goods supplied by us shall be subject to the provisions of sections 55 to 57 of
the Consumer Protection Act (68/2008) except where the provisions of the warranty
contained in our product documentation are more favourable to the purchaser. Subject
to the warranty contained in our product documentation, if applicable, our products are
warranted for a period of twenty-four months after delivery. However, it is expressly
noted that batteries carry a six month warranty due to the nature of these products
being such that they are subject to possible misuse. Please note that warranties will be
honoured on a carry-in basis; in other words, the product in question must be taken in
to one of our branches, or to the authorised reseller that the product was purchased
from, for assessment and, if necessary, repair. For equipment not of our manufacture,
the warranty as supplied by the original manufacturer will apply if such warranty is more
favourable to the purchaser than the relevant provisions of the Consumer Protection Act
(Act 68/2008 of South Africa), or any other applicable law as so required in different
countries in which the product was sold. Such warranty is valid only once full payment
has been received for such goods.
24 MONTH PRODUCT WARRANTY
9. 24 Month Carry-in Product Warranty
Australian customers:
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.. Any warranty may be voidable on any equipment which:
1. Has not been installed in accordance with the installation instructions provided.
2. Has been subject to misuse or which has been used for any purpose other than that
designed for by the manufacturers.
3. Has damage caused as a result of handling during transit, atmospheric conditions
(including lightning), corrosion of metal parts, insect infestation, power surges or
other forces outside of the control of the manufacturer.
4. Has been repaired by any workshop and / or person NOT previously authorised by the
manufacturer.
5. Has been repaired with components not previously tested, passed or authorised by
Centurion Systems (Pty) Ltd, South Africa or one of its subsidiary companies.
page 41
SECTION 9
www.CentSys.com
24 MONTH PRODUCT WARRANTY
SECTION 9
We will not be liable under this contract for any loss or damage caused by us or
our employees or agents in circumstances where:
1. There has been a failure to install the product in accordance with the installation
instructions provided by the manufacturer, or
2. a failure to abide by the safety instructions provided by the manufacturer, or
3. there is no breach of a legal duty of care owed to you by us or by any of our
employees or agents
4. such loss or damage is not a reasonably foreseeable result of any such breach, and
any increase in loss or damage resulting from breach by you of any term of this
contract.
page 42
www.CentSys.com
OPTIONAL EXTRAS
10. Optional Extras
Photon/i5 Infrared Safety Beams
Always recommended on any gate
automation installation.
SMARTGUARD and
SMARTGUARDair keypad
Photon/i5
Infrared
Safety Beams
Cost-effective and versatile
keypad, allowing for access to
pedestrians, armed response
companies, etc
SMARTGUARD and
SMARTGUARD air
keypad
SOLO/Lattice Proximity Access
Control System
Proximity reader, allowing for access
to both pedestrians and vehicles.
while offering a higher level of
security than a keypad
SOLO/Lattice Proximity
Access Control System
Pedestrian Keyswitch
Pedestrian
keyswitch
Allows for pedestrians to partially
open the gate using a key.
POLOphone Intercom System
Allow visitors to communicate with
residents in order to gain access to
the property.
POLOphone
Intercom
Theft-resistant Cage
Retro-installable steel cage that
increases the resistance of the
operator against theft
D5-Evo
Theft-resistant
cage
FIGURE 38
www.CentSys.com
page 43
SECTION 10
D10 Theft-resistant
cage
Connect with us on:
facebook.com/CenturionSystems
YouTube.com/CenturionSystems
@askCenturion
Subscribe to the newsletter: www.CentSys.com/Subscribe
Call Centurion Systems (Pty) Ltd . South Africa
Head Office: +27 11 699 2400
Call Technical Support: +27 11 699 2481
from 07h00 to 18h00 (UTC+2)
Doc number: 0.07.A.0159_24022016
ENGLISH
www.CentSys.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement