Bosch | UML-150-90 | User`s manual | Bosch UML-150-90 User`s manual

Bosch High Performance HD LED Monitors
UML-323-90 | UML-423-90 | UML-553-90
en
User's Manual
Bosch High Performance HD LED Monitors
Table of Contents | en
3
Table of Contents
1
Safety
5
1.1
Important safety instructions
5
1.2
Safety precautions
7
1.3
Important notices
7
1.4
Customer Support and Service
12
2
Unpacking
13
2.1
Parts List
13
3
Access and Connections
14
3.1
Front Control Panel
14
3.2
Rear Panels
14
3.3
Bottom Panel
16
3.4
Remote Control
17
3.5
Remote Control Battery Installation
17
4
Description
19
4.1
Features
19
4.2
Power
19
5
Installing the Monitor
20
5.1
Ventilation
20
5.2
Desktop Installation
20
5.3
Mounting the Monitor to a Wall
21
5.4
Connecting Power
22
5.5
Connecting the Composite Video Signal to the Monitor
22
5.6
Connecting the Y/C (S-Video) Signal to the Monitor
23
5.7
Connecting Audio to the Monitor
23
5.8
Connecting the PC Signal to the Monitor
23
5.8.1
HDMI Connection
23
5.8.2
DVI Connection
23
5.8.3
VGA Connection
23
5.9
Connecting an Alarm Trigger
24
5.10
Single / Multiple Monitor Configuration
25
6
Navigating the Monitor
27
6.1
Navigating the Control Panel
27
6.2
Using the Monitor On-screen Display (OSD)
27
6.3
On-screen Display Menus
28
6.4
Picture Menu
28
6.5
Sound Menu
29
6.6
Option Menu
30
6.6.1
PIP Availability
31
6.7
Setting Menu
31
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
4
7
en | Table of Contents
Bosch High Performance HD LED Monitors
Power Management
34
7.1
Power Consumption
34
7.2
LED Indicator
34
8
Troubleshooting
35
9
Maintenance
36
10
Technical Specifications
37
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Safety | en
1
Safety
1.1
Important safety instructions
5
Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.
1.
Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol
cleaners.
2.
Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3.
Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent
overheating and ensure reliable operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's
instructions have been adhered to.
4.
Water - Do not use this unit near water, for example near a bathtub, washbowl, sink,
laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To reduce the risk of fire or
electrical shock, do not expose this unit to rain or moisture.
5.
Object and liquid entry - Never push objects of any kind into this unit through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled
with liquids, such as vases or cups, on the unit.
6.
Lightning - For added protection during a lightning storm, or when leaving this unit
unattended and unused for long periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to the unit from lightning and
power line surges.
7.
Controls adjustment - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit. Use of controls or
adjustments, or performance of procedures other than those specified, may result in
hazardous radiation exposure.
8.
Overloading - Do not overload outlets and extension cords. This can cause fire or
electrical shock.
9.
Power cord and plug protection - Protect the plug and power cord from foot traffic,
being pinched by items placed upon or against them at electrical outlets, and its exit
from the unit.
10. Power disconnect - Units have power supplied to the unit whenever the power cord is
inserted into the power source. The power cord is the main power disconnect device for
switching off the voltage for all units.
11. Power sources - Operate the unit only from the type of power source indicated on the
label. Before proceeding, be sure to disconnect the power from the cable to be installed
into the unit.
–
For battery powered units, refer to the operating instructions.
–
For external power supplied units, use only the recommended or approved power
supplies.
–
For limited power source units, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
–
If unsure of the type of power supply to use, contact your dealer or local power
company.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
6
en | Safety
Bosch High Performance HD LED Monitors
12. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
13. Damage requiring service - Unplug the unit from the main AC power source and refer
servicing to qualified service personnel when any damage to the equipment has
occurred, such as:
–
the power supply cord or plug is damaged;
–
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
–
liquid has been spilled in or on the equipment;
–
an object has fallen into the unit;
–
unit has been dropped or the unit cabinet is damaged;
–
unit exhibits a distinct change in performance;
–
unit does not operate normally when the user correctly follows the operating
instructions.
14. Replacement parts - Be sure the service technician uses replacement parts specified by
the manufacturer, or that have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical shock, or other hazards.
15. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.
16. Installation - Install in accordance with the manufacturer's instructions and in
accordance with applicable local codes.
17. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
1.2
Safety | en
7
Safety precautions
DANGER!
High risk: This symbol indicates an imminently hazardous situation such as “Dangerous
Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of damage to the unit.
1.3
Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3 mm in each pole, into the electrical installation of the building.If it is needed to open
the housing for servicing and/or other activities, use this all-pole switch as the main
disconnect device for switching off the voltage to the unit.
Coax grounding:
–
–
Ground the cable system if connecting an outside cable system to the unit.
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a
ground source.
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting
the grounding plug or grounding terminal.
–
Follow proper safety precautions such as grounding for any outdoor device connected to
this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
Disposal - Your Bosch product was developed and manufactured with high-quality material
and components that can be recycled and reused. This symbol means that electronic and
electrical appliances, which have reached the end of their working life, must be collected and
disposed of separately from household waste material. Separate collecting systems are
usually in place for disused electronic and electrical products. Please dispose of these units
at an environmentally compatible recycling facility, per European Directive 2002/96/EC
Electronic Surveillance - This device is intended for use in public areas only. U.S. federal law
strictly prohibits surreptitious recording of oral communications.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
8
en | Safety
Bosch High Performance HD LED Monitors
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid
electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when
handling the electrostatic-sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Grounding and polarization - This unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other blade). This safety feature allows the
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device in
the building installation wiring.
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
Power resupply - If the unit is forced to power down due to exceeding the specified operating
temperatures, disconnect the power cord, wait for at least 30 seconds, and then reconnect
the power cord.
Power lines - Do not locate the display near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
Rack-mount
–
Ventilation - Do not place this unit in a built-in installation or rack without proper
ventilation or adhering to the manufacturer's instructions. The equipment must not
exceed its maximum operating temperature requirements.
–
Mechanical loading - Properly mount the equipment in a rack to prevent a hazardous
condition due to uneven mechanical loading.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the
SELV circuit to the Telephone Network Voltage (TNV) circuits.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Safety | en
9
System ground/Safety ground
The system ground is only used to comply with safety standards or installation practices in
certain countries. Bosch does not recommend connecting system ground to safety ground
unless it is explicitly required. However, if the system ground and safety ground are
connected and grounding loops are causing interference in the video signal, use an isolation
transformer (available separately from Bosch).
CAUTION!
Connecting System ground to Safety ground may result in ground loops that can disrupt the
CCTV system.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,
redundant recording systems, and a procedure to back up all analog and digital information.
NOTICE!
This is a class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
–
this device may not cause harmful interference, and
–
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible
for compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet
is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000-00345-4.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
10
en | Safety
Bosch High Performance HD LED Monitors
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux
conditions suivantes :
–
–
cet appareil ne peut pas provoquer d'interférence nuisible et
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement.
AVERTISSEMENT : Suite à différents tests, cet appareil s’est révélé conforme aux exigences
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont destinées
à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est
utilisé dans une installation commerciale. Cette appareil génère, utilise et émet de l'energie
de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux
instructions, générer des interférences nuisibles aux communications radio. L’utilisation de ce
produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission
fédérale des communications (FCC), peut s’avérer utile : How to Identify and Resolve Radio-TV
Interference Problems (Comment identifier et résoudre les problèmes d’interférences de radio
et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office,
Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Safety | en
11
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Closed Circuit Television Equipment, UL
2044. UL Certification does not cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED
FUNCTIONS OF THIS PRODUCT.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information Technology Equipment, UL
60950-1. UL Certification does not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALINGRELATED FUNCTIONS OF THIS PRODUCT.
Copyright
This manual is the intellectual property of Bosch Security Systems and is protected by
copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
NOTE!
This manual has been compiled with great care and the information it contains has been
thoroughly verified. The text was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the user guide can change without
notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user guide and the product
described.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
12
1.4
en | Safety
Bosch High Performance HD LED Monitors
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
USA
Repair CenterTelephone: 800-566-2283
Fax: 800-366-1329
E-mail: repair@us.bosch.com
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
E-mail: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
E-mail: technical.support@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500
Fax: 31 (0) 76-5721413
E-mail: RMADesk.STService@nl.bosch.com
Asia Region
Repair Center
Telephone: 65 63522776
Fax: 65 63521776
E-mail: rmahelpdesk@sg.bosch.com
Customer Service
Telephone: 86 (0) 756 7633117 or
86 (0) 756 7633121
Fax: 86 (0) 756 7631710
E-mail: customer.service@cn.bosch.com
Warranty and more information
For additional information and warranty queries, please contact your Bosch Security Systems
representative or visit our website at www.boschsecurity.com.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
2
Unpacking | en
13
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
2.1
Parts List
Quantity Description
1
One of the following Color LED Flat Panel Monitors:
1
1
1
2
UML-323-90, UML-423-90 or UML-553-90
Installation manual (printed booklet, English version)
Installation manual (printed booklet, Japanese version)
Installation manual (CD-ROM, multi-language version)
Power Cords, 3-wire with grounded plug 1.8 m (6 ft) long:
1
1
1
1
2
one with a U.S plug type and one with a European Continental plug type
DVI-D to DVI-D cable, 1.8 m (6 ft)
VGA to VGA (D-Sub) cable, 1.8 m (6 ft)
Trigger cable
Remote control
AAA batteries
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
14
en | Access and Connections
Bosch High Performance HD LED Monitors
3
Access and Connections
3.1
Front Control Panel
Figure 3.1 UML-323-90/UML-423-90/UML-553-90 Front Panel
Ref. Button
Description
1
IR sensor and Receives the command signals from the remote control.Indicates the
LED Indicator operating status of the monitor:Power On (green)Power Off, Standby
(red)
3.2
Rear Panels
UML-323-90
1
2
3
4
5
6
7
8
Figure 3.2 UML-323-90 Rear Panel
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Access and Connections | en
15
UML-423-90
1
2
3
4
5
6
7
8
Figure 3.3 UML-423-90 Rear Panel
UML-553-90
1
2
3
4
5
6
7
8
Figure 3.4 UML-553-90 Rear Panel
Ref. # Button/Part
1
LED Indicator
Description
Indicates the operating status of the monitor:
Power On (green)
Power Off, Standby (red)
Display Power (On/Off)
Increases the value when in the OSD.
Scrolls right in the OSD.
4
Increases audio volume.
Decreases the value when in the OSD.
Scrolls left in the OSD.
5
Decreases audio volume.
Adjusts the value when in the OSD.
Scrolls up in the OSD.
6
Adjusts the value when in the OSD.
Scrolls down in the OSD.
2
3
Power
Activates the Auto Adjustment function
7
8
MENU
VIDEO
when in PC mode.
Selects the on-screen display (OSD).
Selects the signal to be displayed.
SOURCE/ENTER Serves as the “Enter” function for OSD menus.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
16
3.3
en | Access and Connections
Bosch High Performance HD LED Monitors
Bottom Panel
4
1
2
3
10 11
6
5
7
8
9
12 13
14
15 16 17 18
19
Figure 3.5 Bottom View (I/O Panel)
Ref.
1
2
3
4
5
6
7
8
9
10
F.01U.134.499 | 2.0 | 2012.10
Connector
HDMI IN
DVI-D IN
VGA OUT
VGA IN
RS-232 OUT (for firmware update)
RS-232 IN (for firmware update)
VIDEO IN - COMPONENT
VIDEO IN - S-VIDEO
VIDEO OUT
VIDEO IN
User's Manual
Ref.
11
12
13
14
15
16
17
18
19
Connector
TRIGGER INPUT
AUDIO IN - AUDIO 1
AUDIO OUT (R/L)
SPEAKERS (R/L)
AUDIO IN - AUDIO 2
AUDIO IN - AUDIO 3
AC SWITCH ON/OFF
100 - 240 VAC IN
100 - 240 VAC OUT
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
3.4
Access and Connections | en
17
Remote Control
1
19
2
3
4
5
6
7
8
9
10
11
12
13
20
14
15
16
27
21
22
23
24
25
26
17
18
28
Ref.
1
2
3
Button
POWER
Contrast
Backlight
Description
Turns power on and off.
Adjusts picture contrast.
Adjusts backlight intensity of LCD
4
5
6
Color Tone
Auto. Adj.
Info
panel.
Adjusts color temperature of picture.
Auto adjusts the graphics adaptor.
Displays the settings of the selected
7
8
9
input.
Mute
Mutes the sound.
Auto Switching Selects the Auto Switch function.
PIP
Selects the Picture-in-Picture (PIP)
10
11
12
13
14
15
16
17
YPbPr
PC
AV 1
AV 2
Input
Exit
(no function)
Arrow Keys
Enter
function.
Selects YPbPr mode.
Selects PC mode.
Selects AV1 mode.
no function
Selects a signal source to display.
Exits the OSD menu.
Moves the cursor down, up, left, and
right in the OSD.
Accepts a selection in an OSD menu.
18
19
20
(no function)
Brightness
P. Mode
Adjusts picture brightness.
Selects the picture mode.
Continuously press to change the
21
Size
selection.
Selects the screen ratio when in
Video mode. Continuously press to
22
23
24
25
26
27
Trigger
HDMI
DVI2
DVI1
S-Video
MENU
change the selection.
Selects the trigger function.
Selects HDMI mode.
no function
Selects DVI1 mode.
Selects S-Video mode.
Displays the OSD Main menu. Press
to return to the Main menu from
anywhere in the OSD menus.
28
Bosch Security Systems, Inc.
(no function)
User's Manual
F.01U.134.499 | 2.0 | 2012.10
18
3.5
en | Access and Connections
Bosch High Performance HD LED Monitors
Remote Control Battery Installation
1.
2.
Turn the remote over (buttons facing down) and push down on the cover and slide it off.
Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks
inside the battery case.
3.
Slide the battery cover back into place.
1
1
2
2
Figure 3.6 Remote Control Battery Replacement
Note: Replace batteries when required or at least once a year. Dispose of used batteries
properly
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
4
Description | en
19
Description
The Bosch High Performance Family of LCD monitors display PAL or NTSC standard color
pictures in CCTV systems. One (1) looping Composite Video BNC connector input, one
Component Video BNC connector input, three (3) Audio input RCA, and one (1) Y/C (S-Video)
input using a 4-pin mini-DIN are included. In addition, each model includes an Analog VGA
input using 15-pin D-sub to accommodate the increasing use of PCs and digital video devices
in security applications, an HDMI (High Definition Multimedia Input), DVI, PC-RGB (VGA)
connectors.
Monitor control functions are accessed via the push buttons and on-screen display (OSD).
Refer to Section 3 Access and Connections, page 14, for front panel descriptions.
4.1
Features
–
32-inch, 42-inch and 55-inch models
–
NTSC/PAL Auto-Detect
–
VGA Input
–
640 x 480 (60/72/75 Hz)
–
720 x 400 (70 Hz)
–
800 x 600 (60/75 Hz)
–
1024 x 768 (60/75 Hz)
–
1280 x 768 (60 Hz)
–
1280 x 960 (60 Hz)
–
1280 x 1024 (60 Hz)
–
1366 x 768 (60 Hz)
–
1600 x 1200 (60 Hz)
–
1920 x 1080 (60 Hz)
–
Composite Video Input
–
Component Video Input
–
Y/C Input (S-Video)
–
DVI Input
–
HDMI Input (480i 60Hz, 480p 60Hz, 576i 50 Hz, 576p 50Hz, 720p 50/60Hz, 1080i 50/
60Hz, 1080p 50/60Hz)
4.2
–
Trigger input
–
On-screen Display (OSD) with Multiple Languages
Power
Model No.
UML-323-90
Rated Voltage
120/230 VAC
Voltage Range
100 to 240 V
Power at Rated Voltage Sync Format
< 75 W
NTSC/PAL
UML-423-90
50/60 Hz
120/230 VAC
100 to 240 V
< 150 W
NTSC/PAL
UML-553-90
50/60 Hz
120/230 VAC
100 to 240 V
< 170 W
NTSC/PAL
50/60 Hz
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
20
5
en | Installing the Monitor
Bosch High Performance HD LED Monitors
Installing the Monitor
This chapter outlines the procedures to install the monitor. A qualified service person should
install the monitor and adhere to all local codes.
5.1
Ventilation
To prevent overheating, ensure that the ventilation openings on the rear of the monitor are
not covered.
5.2
Desktop Installation
The desktop stands can be installed on the rear panel of the monitor for desktop application.
UML-323-90
UML-423-90
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Installing the Monitor | en
21
UML-523-90
5.3
Mounting the Monitor to a Wall
The monitor may be mounted to a wall using the mounting holes and a suitable wall mount or
swivel/tilt mount. Use a UL-Listed mounting device. Ensure that the mount is strong enough to
bear the weight of the monitor, as follows:
–
UML-323-90: 12.5 kg (27.6 lb)
–
UML-423-90: 20 kg (44.1 lbs)
–
UML-553-90: 32 kg (70.5 lbs)
Refer to the figures below for the dimensions of the mounting holes.
200 mm
200 mm
Figure 5.1 UML-323-90 - Location of mounting holes
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
22
en | Installing the Monitor
Bosch High Performance HD LED Monitors
400 mm
400 mm
Figure 5.2 UML-423-90 - Location of mounting holes
400 mm
400 mm
Figure 5.3 UML-553-90 - Location of mounting holes
5.4
Connecting Power
The Bosch Flat Panel CCTV monitors are delivered with a 3-pole US-style power cord and a 3pole Euro-style power cord. Use the US-style power cord where 120 VAC, 60 Hz power is
available; use the Euro-style power cord where 230 VAC, 50 Hz power is available. The
monitor automatically adjusts to either power input voltage.
5.5
Connecting the Composite Video Signal to the Monitor
There is one (1) BNC connector located on the rear panel of the monitor for composite video
input and one (1) BNC connector for composite video output (Refer to Section 3.2 Rear
Panels, page 14).
Note: All video inputs are passive loop-through. The impedance is automatically set to 75 ohm
by the input of the signal on the input connector, while operating in a single connection mode
(refer to Figure 5.9). If a cable is also connected to the output connector, the video signal can
be passed on to another monitor connected to it via the passive loop-through function. Up to
three (3) monitors may be connected in this manner (refer to Figure 5.10).
Note: To select AV1, press VIDEO SOURCE/ENTER, and then press the Up or Down arrow
button, located on the front of the monitor.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
5.6
Installing the Monitor | en
23
Connecting the Y/C (S-Video) Signal to the Monitor
There is one (1) mini-DIN type connector for the S-Video (Y/C) input (refer to Section 3.2 Rear
Panels, page 14) on the rear side panel.
Note: Both Y and C inputs are terminated with 75 Ohm.
Figure 5.4 Y/C Connector pin-out
Number
1
2
3
4
5.7
Input
Ground
Ground
Y-signal
C-signal
Connecting Audio to the Monitor
There are three (3) set of stereo audio connectors for audio inputs, located on the rear
panel.This audio inputs are not associated with any input terminals on the rear panel, and can
be freely connected to any audio input.
5.8
Connecting the PC Signal to the Monitor
There are three ways to connect the PC signal to the monitor: HDMI, DVI, and VGA.
5.8.1
HDMI Connection
The monitor can be connected to the HDMI (High Definition Multimedia Input) by connecting
a HDMI cable (not supplied).
Figure 5.5 HDMI Input
5.8.2
DVI Connection
The monitor can be connected by using the supplied DVI-D cable and connecting it to the
digital DVI-D signal.
Figure 5.6 DVI Input
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
24
en | Installing the Monitor
5.8.3
Bosch High Performance HD LED Monitors
VGA Connection
You can connect PC signal to the monitor using the VGA connector on the rear panel and a
VGA cable (D-SUB to D-SUB).
Figure 5.7 VGA Input
Pin
1
2
3
4
5
5.9
Description
Red Video
Green Video
Blue Video
Ground
Ground
Pin
6
7
8
9
10
Description
Red Ground
Green Ground
Blue Ground
N/A
Signal Cable Detect
Pin
11
12
13
14
15
Description
Ground
SDA (for DDC)
H-Sync or H+V Sync
V-Sync
SCL (for DDC)
Connecting an Alarm Trigger
The monitor contains an alarm Trigger Input and a Trigger cable. These components allow you
to connect an alarm relay from a device, such as a camera or a door. Connect the two flying
leads from the Trigger cable into the relay out ports of the device. Then, route the other end
of the cable to the Trigger Input connector of the monitor. The following illustration depicts a
typical alarm relay configuration.
Figure 5.8 Camera to Monitor Relay
Number
1
2
3
Description
Dinion Camera
Flying Leads Connected to Trigger Outputs3 and 4
UML Back Panel
In the above example, the flying leads of the Trigger cable are connected to Trigger output
three and four of a Dinion camera. The cable is routed to the back panel of the UML monitor
and the plug-end of the wire is connected to the Trigger Input port. Refer to
Section 6.7 Setting Menu, page 31, for configuring alarm acknowledgement.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Installing the Monitor | en
25
Example: Typical Alarm Trigger Configuration
In this case, the Dinion camera is used to watch for motion. When the camera detects motion
it sends an alarm to the UML monitor. The monitor, then, switches the input to display the
video from the Dinion camera and sounds a buzzer.
1.
2.
3.
Route the coax cable from the Dinion Video output to the AV1 input of the UML monitor.
Configure the following settings for the Dinion camera:
–
VMD: OSD
–
Area: 1
–
Active: On
Connect one flying lead to relay output three, on the back of the Dinion camera, and
connect the other to relay output four.
4.
Connect the other end of the Trigger Relay cable to the Trigger Input connector on the
back of the monitor.
5.
6.
Plug the monitor into a power socket; then press the Power button.
On the monitor, access the Trigger menu:
a.
Press the Menu button.
b.
Press the Down arrow button to access the Setting menu.
c.
Press the Right arrow button to enter the Setting menu.
d.
Press the Down arrow button until Trigger is highlighted; then press the Right arrow
button.
7.
Make the necessary changes to the Trigger menu so that the settings match the
following:
Trigger Enable
Trigger Input
Buzzer
Trigger Time
Trigger Option
:Move
Bosch Security Systems, Inc.
On
AV1
On
10
High
:Enter
User's Manual
:Exit
F.01U.134.499 | 2.0 | 2012.10
26
en | Installing the Monitor
5.10
Bosch High Performance HD LED Monitors
Single / Multiple Monitor Configuration
1
3
2
4
Figure 5.9 Single Monitor Configuration
Ref
1
2
Description
Ref
Video Camera 3
Video In
4
Description
Video Out
DVR
1
3
2
3
2
2
Figure 5.10
Ref
1
2
3
F.01U.134.499 | 2.0 | 2012.10
Multiple Monitor Configuration
Description
Video Camera
Video In
Video Out
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Navigating the Monitor | en
6
Navigating the Monitor
6.1
Navigating the Control Panel
27
Use the control panel to make any necessary OSD adjustments. See the figure below for an
explanation of the control panel.
1
2
3
4
5
6
7
Figure 6.1 Control Panel Buttons
Ref. Button
1
Power
Description
Display Power (On/Off)
2
Generate sounds from the input audio signal.
Increases the value when in the OSD.
Scrolls right in the OSD.
3
Increases audio volume.
Decreases the value when in the OSD.
Scrolls left in the OSD.
4
Decreases audio volume.
Adjusts the value when in the OSD.
Scrolls up in the OSD.
5
Adjusts the value when in the OSD.
Scrolls down in the OSD.
6
7
Menu
VIDEO
Auto adjusts when in PC mode.
Selects the on-screen display (OSD).
Selects the signal to be displayed
SOURCE/ENTER Serves as the “Enter” function for OSD menus
6.2
Using the Monitor On-screen Display (OSD)
The LCD is programmed through the on-screen display (OSD) menus and submenus where an
operator can select operating parameters. To access the OSD menus, press the Menu button
on the control panel. Use these controls to make any necessary adjustments to the OSD.
NOTICE!
When you are navigating through the OSD menus, use the SOURCE or ENTER button to select
a menu and use the MENU button to exit a menu.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
28
en | Navigating the Monitor
Bosch High Performance HD LED Monitors
To navigate the set up menus, follow the steps below:
1.
Connect a video source cable to the monitor.
2.
Press the Power button to turn on the unit.
3.
If required, press the SOURCE or ENTER button and then the and the
and
buttons
until a signal is displayed.
4.
Press the Menu button to activate the main menu selections.
5.
Press the
6.
Press the
7.
Press the
and
buttons to select a sub-menu item.
8.
Press the
and
buttons to toggle the OSD values.
9.
Press the Menu button to exit the selected menu and to return to the menu bar or to
and
buttons to select a menu.
button to enter the selected menu.
confirm a selection.
10. Press the Menu button again to exit the OSD menu bar.
6.3
On-screen Display Menus
There are four (4) on-screen menus that allow you to customize your settings. Press the Menu
button to access the OSD menu.
Icon
Menu
Picture
Function
Adjusts picture quality relevant settings. (The menu options differ
between input signals.)
Sound
Adjusts sound relevant settings. (The menu options differ between the
Video and PC modes.)
Option
Adjusts the Aspect Ratio, PIP, Video Source, Auto Adjustment, Clock
Settings
Detection settings.
Resets the factory default settings and adjusts the overall monitor
Frequency, Phase, H Position, V Position, Ambient Light Sensor, and Auto
settings.
Note: Some of the OSD menu functions may not be available according to the input source
detected.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
6.4
Navigating the Monitor | en
29
Picture Menu
To access the Picture menu, press the Menu button on the front panel of the monitor, then
press the Up and Down arrow buttons to select the Picture icon. Press the Left arrow button
to enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
Picture
PIcture Mode
Contrast
Brightness
Color
Tint
Sharpness
Backlight
DCR
Color Temp
Input Resolution
Blue Screen
:Move
:Enter
Standard
50
50
50
50
5
100
OFF
9300°K
ON
:Exit
Submenu
Definition
Picture Mode
Selects the automatic picture control mode. Choices are:
Standard: applies factory default values.
Vivid: for viewing very bright images.
Cinema: for viewing movies.
User: creates your own picture settings. This mode is automatically
selected after you change the settings in the Picture menu.
Contrast
Adjusts the contrast level for video performance (range 0-100).
Brightness
Adjusts the brightness level for video performance (range 0-100).
Color
Adjusts the overall color intensity of the screen (range 0-100).
Tint
Adjusts the tint of the picture (range 0-100). NTSC only.
Sharpness
Adjusts the sharpness level for video performance (range 0-100).
DCR
When turned on, this function helps enhance image contrast when
displaying dark scenes.
Color Temp
Selects the color temperature. Choices are:
–
12000°K, 9300°K, and 6500°K .
–
Options under User: Red, Green, and Blue (range 0-255).
Input Resolution Sets the resolution of the VGA input. This setting is required when the
monitor is unable to detect the VGA input resolution correctly. Choices
are Auto, 1366 x 768, 1360 x 768, 1280 x 768.
Blue Screen
Bosch Security Systems, Inc.
Enables or disables video loss indication. Choices are:
–
ON: displays a blue background when video loss is detected.
–
OFF: displays a black background when video loss is detected.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
30
6.5
en | Navigating the Monitor
Bosch High Performance HD LED Monitors
Sound Menu
To access the Sound menu, press the Menu button on the control panel of the monitor, then
press the UP and Down arrow buttons to select the Sound icon. Press the Left arrow button
to enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
Sound
Volume
Mute
Audio Source
Speaker
:Move
100
OFF
Audio 2
External
:Enter
:Exit
Submenu
Definition
Volume
Controls the built-in speaker volume (range 0-100).
Mute
Enables/disables audio. Choices are: On and Off.
Audio
Selects the audio input source. Choices are: Audio 1 (audio signal from the
Source
Audio IN connector) and HDMI (audio signal from the HDMI connector).
Speaker
Sets the monitor to play audio using the external speakers, external audio
devices (if connected), or built-in (internal) speaker. Choices are: External,
Line-Out, and Internal.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
6.6
Navigating the Monitor | en
31
Option Menu
To access the Option menu, press the Menu button on the control panel of the monitor, then
press the UP and Down arrow buttons to select the Option icon. Press the Left arrow button
to enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
Options
Aspect Ratio
PIP
Video Source
Auto Adjustment
Clock Frequency
Phase
H Position
V Position
Ambient Light Sensor
Auto Detection
:Move
Full
AV
External
:Enter
Submenu
Aspect Ration
PIP
:Exit
Definition
Selects the Aspect Ratio mode. Choices are: Full and Original.
Sets the PIP relevant settings.
–
PIP Enable: activates the PIP feature.
–
Main Input and Sub Input: selects the video input source for the
main picture and the sub picture. Refer to Section 6.6.1 PIP
Availability, page 31, for the availability of the input source
combinations.
–
PIP Size: selects the size of the sub picture. Choices are: Large
and Small.
–
PIP Position: adjusts the position of the sub picture on the main
Video Source
picture. Press the arrow buttons to make adjustments.
Selects the video input source. Choices are: AV, S-Video, VGA,
Auto Adjustment
Clock Frequency
Phase
H Position
V Position
Ambient Light Sensor
YPbPr, DVI, and HDMI.
Auto synchronizes the screen to the graphics adaptor.
Adjusts the monitor’s clock frequency (range 0-31).
Adjusts the monitor’s phase range (range 0-31).
Adjusts the monitor’s horizontal position (range 0-31).
Adjusts the monitor’s vertical position (range 0-31).
Sets the ambient light sensor. Once enabled, the monitor
automatically adjusts the image brightness as the ambient lighting
Auto Detection
conditions change. Choices are: High, Low, and OFF.
Allows the monitor to automatically switch to and display an available
input signal.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
32
en | Navigating the Monitor
6.6.1
Bosch High Performance HD LED Monitors
PIP Availability
The table below summarizes the availability of the input source combinations for the PIP
feature. (A “+” indicates an allowed combination, a blank cell indicates the combination is not
allowed).
Main Picture Input Source
S-Video Comp.
PC
DVI
+
+
+
AV
Sub
AV
Picture S-Video
Comp.
PC
DVI
HDMI
6.7
+
+
+
+
HDMI
+
+
+
+
+
Setting Menu
To access the Setting menu, press the Menu button on the control panel of the monitor, then
press the UP and Down arrow buttons to select the Setting icon. Press the Left arrow button
to enter the menu, and then press the Up and Down arrow buttons to select a submenu. When
finished, press the Menu button to save any changes, then press the Menu button again to exit
the OSD.
Setting
Language
Overscan
Key Lock
Trigger
Schedule
Display Wall
Power Save
Set Monitor ID
Image Retention
Auto Adjustment
Advanced
:Move
Submenu
Language
English
OFF
OFF
OFF
1
ON
ON
:Enter
:Exit
Definition
Adjusts the language of the OSD. Choices are: English, French,
Spanish, Dutch, German, Italian, Portuguese, Russian, Polish,
Overscan
Simplified Chinese and Japanese.
Turns the overscan function on or off when displaying video (non-PC)
Key Lock
signals
Enables or disables the Key Lock function.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
Trigger
Navigating the Monitor | en
33
Enables or disables the Trigger function, and configures the trigger
settings when enabled:
–
Trigger Enable: turns the Trigger function ON or OFF.
–
Trigger Input: selects the input signal source to display when a
trigger signal is received.
–
Buzzer: turns the trigger buzzer tone ON or OFF.
–
Trigger Time: sets the time duration the trigger input (as set by the
Trigger Input function) is displayed. Once the time expires, the
monitor automatically switches back to the last viewed input.
–
Schedule
Trigger Option: sets the trigger signal type: N/C (normal closed),
N/O (normal opened), High (2~5V) or Low (0~0.6V).
This function allows you to program up to seven (7) different scheduled
time intervals for the monitor. You can select the time the monitor turns
on and turns off, the days in a week it is activated, and which input
source the display will use for each scheduled activation period.
–
Date and Time: Sets up current date and time for the monitor’s
internal clock before using the Schedule function. Choices are
Year, Month, Day, Hour, Minute, Daylight Saving Time. Once done,
you will see the current date and time in this menu.
–
Schedule: Sets up to seven (7) schedule time intervals with
different video input modes.
Note:
–
If you do not want to use a power on time, select “--” for the power
on hour slot, and “00” for the minute slot. The monitor will only
turn off at the time you set.
–
If you do not want to use a power off time, select “--” for the power
off hour slot, and “00” for the minute slot. The display will only turn
on at the time you set.
–
If no input source is selected, the default input source (Video) will
be used.
–
If Every Day is selected, the monitor will turn on everyday
regardless of other day settings (for example, Monday, Tuesday,
Wednesday...).
–
Should schedule periods overlap, the power on time has priority
over power off time. For example, if schedule item #1 sets the
monitor to power on at 10:00 AM and off at 5:00 PM, and schedule
item #2 sets the display to power on at 4:00 PM and off at 9:00 PM
on the same day, then the monitor will power on at 10:00 AM and
off at 9:00 PM.
–
If there are multiple schedule items programmed for the same time
period, then the highest numbered schedule item has priority. For
example, if schedule items #1 and #2 both set the display to power
on at 7:00 AM and off at 5:00 PM, then only schedule item # 1 will
take effect.
Bosch Security Systems, Inc.
User's Manual
F.01U.134.499 | 2.0 | 2012.10
34
en | Navigating the Monitor
Display Wall
Bosch High Performance HD LED Monitors
If multiple monitors are tiled to form a display wall, use this function to
set up the display wall settings:
–
H Monitors: selects the number of displays on the horizontal side
(range 1-10).
–
V Monitors: selects the number of displays on the vertical side
(range 1-10).
–
H Position: selects the horizontal position of the monitor in the
display wall matrix (range 1-10).
–
V Position: selects the vertical position of the monitor in the
display wall matrix (range 1-10).
–
Frame Comp.: turns frame compensation on or off. If turned on,
the monitor adjusts the image to compensate for the width of the
Power Save
bezels in order to accurately display the image.
Sets the monitor to reduce the power consumption:
–
Eco: all sources can enter the power saving mode, but only a VGA
signal can wake up the monitor or you have to press the Power
button to wake up the monitor when other source is connected.
–
Standard: all source can enter the power saving mode and wake up
the monitor.
Set Monitor ID
–
Off: if no source is detected, the backlight remains on.
–
VGA Only: only a VGA signal can enter the power saving mode and
wake up the monitor.
Sets the ID number for controlling the monitor via the RS 232
connection. Each monitor must have a unique ID number when multiple
monitors are connected. Each monitor’s ID is defined by its position
within the matrix - starting on the top row, working left to right. The top
left monitor will have an ID of 1. When you reach the end of the row, the
Image Retention
next number will refer to the monitor one row down, starting at the left.
If turned on, the LCD monitor automatically displays swift moving
Auto Adjustment
patterns to prevent the formation of image retention on the screen.
Turns on or off to let the monitor auto synchronizes screen to graphics
Advanced
adaptor.
–
Restore User Default: restores default settings.
–
OSD Info Box: when turned ON, the monitor always displays the
current input source and resolution. Select OFF to display the
information box only when you press Info on the remote control.
–
Thermal (°C): displays the thermal status (temperature) inside the
display.
–
Ambient Light (Lux): displays the ambient brightness detected by
the display’s sensor.
–
5V Detect (V): displays the 5V voltage detection result.
–
12V Detect (V): displays the 12V voltage detection result.
–
Operating Time (Day & hr): displays the duration the display has
–
Input Source: displays the selected input source.
been turned on.
NOTICE!
When Key Lock is enabled through the front panel, use the front panel buttons to disable the
key lock command. To disable the Key Lock feature using the front panel buttons, press and
hold both the INPUT (or ENTER) and the MENU buttons until the monitor displays the Key
Unlocked message.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
34
7
en | Power Management
Bosch High Performance HD LED Monitors
Power Management
These monitors feature a power management system to “power down” upon receipt of the
display power management signaling (DPMS) from a DPMS video card.
The DPMS-compliant video card performs this signaling by not sending a horizontal, vertical,
or a sync signal.
The monitor enters an appropriate mode through identifying each of the three (3) modes of
the signaling system.
7.1
Power Consumption
Mode
ON
ACTIVE OFF
7.2
UML-323-90
Power Consumption
UML-423-90
UML-553-90
75 W
0.5 W
150 W
0.5 W
170 W
0.5 W
LED Indicator
The power management feature of the monitor is comprised of these stages:
Mode
LED Color
ON
Green
UNSUPPORTED MODE Green
Monitor Operation
Normal Operation
Normal operation but the screen displays an error
POWER OFF
message.
Not Operational
F.01U.134.499 | 2.0 | 2012.10
Red
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
8
Troubleshooting | en
35
Troubleshooting
Problem
No image displayed on
Solution
–
Check that the power cord of the monitor is securely
screen
connected into the wall outlet or grounded extension cable or
strip.
Display image is not
–
Power switch should be in the ON position and the LED lit.
–
Check that the Brightness and/or Contrast adjustments of the
display have not been turned down to minimum levels.
Push the down arrow key to activate the Auto Adjust function.
centered, is too small or - or too large in the PC mode Adjust the Frequency and Phase in the PC OSD submenu.
Push the down arrow key to activate the Auto Adjust function.
Vertical or horizontal
noise is present in the
- or -
picture
Incorrect colors
Adjust the Frequency and Phase in the PC OSD submenu.
Select a color temperature in the Color Tone menu.
- or -
The error message “Out
Use the Reset function to reset to the default settings.
PC is operating with either a resolution or timing mode that is not
of Range” is displayed
supported by the monitor. Change the PC timing mode to one of
the valid combinations below:
Bosch Security Systems, Inc.
–
640 x 480 (60/72/75Hz)
–
720 x 400 (70Hz)
–
800 x 600 (60/75Hz)
–
1024 x 768 (60/75Hz)
–
1280 x 768 (60Hz)
–
1280 x 960 (60Hz)
–
1280 x 1024 (60Hz)
–
1366 x 768 (60Hz)
–
1600 x 1200 (60Hz)
–
1920 x 1080 (60Hz)
User's Manual
F.01U.134.499 | 2.0 | 2012.10
36
9
en | Maintenance
Bosch High Performance HD LED Monitors
Maintenance
To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a
soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods. If
the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft lintfree cloth to remove the residue as follows:
1.
Turn off the display and disconnect it from the power supply.
2.
Do not spray any liquid directly on the screen. Dampen a clean, soft, lint-free cloth with
water only (using a paper towel or dirty cloth can scratch the screen).
3.
Gently wipe the screen starting from the top of the screen to bottom wiping in a
downward motion. Be careful not to press too hard to avoid damaging the screen.
4.
To avoid streaking, wipe the screen again with another clean, dry, lint-free cloth.
NOTICE!
If water does not work, use a mild cleaner labeled for use with LCD panels, available at office
supply stores.
Do not use any of the following as a cleaning agent:
–
Ketone type materials
–
Ethyl alcohol
–
Ethyl acid
–
Toluene
–
Methyl chloride
–
Ammonia
Use of these materials may permanently damage the polarizer due to a chemical reaction.
F.01U.134.499 | 2.0 | 2012.10
User's Manual
Bosch Security Systems, Inc.
Bosch High Performance HD LED Monitors
10
Technical Specifications | en
37
Technical Specifications
Model
LCD Specifications
LCD Type
Backlight Type
Pixel Pitch (H x V)
Brightness
Contrast Ratio
Response Time
Resolution (H x V)
Frequency
UML-323-90
UML-423-90
UML-553-90
32-in. Digital LCD
LED
0.3637 x 0.3637
42-in. Digital LCD
LED
0.4845 x 0.4845 mm
55-in. Digital LCD
LED
0.21 x 0.21 mm
350 cd/m2 (typical)
3000:1 (typical)
3.5 ms (typical)
1920 x 1080
Horizontal: 60 - 73 KHz
500 cd/m2 (typical)
4000:1 (typical)
8 ms (typical)
1920 x 1080
Horizontal: 60 - 73 KHz
450 cd/m2 (typical)
4000:1 (typical)
6.5 ms (typical)
1920 x 1080
Horizontal: 60 - 73 KHz
Vertical: 47 - 63 Hz
Vertical: 47 - 63 Hz
Vertical: 47 - 63 Hz
Video (BNC 1ch input 1.0 Vp-p, 75 Ohm terminated, loop-through out)
Input Signal
S-Video (Mini Din 4-pin 1ch input (Y/C))
HDMI
DVI-D
PC RGB (D-Sub connector)
Audio In (L/R) x 2
Line In (3.5 mm)
Trigger In
RS-232 (D-Sub 9 pin)
Video (BNC 1ch input 1.0 Vp-p, 75 Ohm terminated, loop-through out)
Output Signal
External Speaker
PC RGB (D-Sub Connector)
RS-232 (D-Sub 9 pin)
930.24 x 523.26 mm
Active Display Area
698.4 mm x 392.85 mm
(H x V)
Packing Dimensions
(27.5 x 15.5 in.)
910 x 608 x 205 mm(35.83
(36.6 x 20.6 in.)
1234 x 786 x 275 mm
(47.6 x 26.8 in.)
1379 x 850 x 273 mm
x 23.94 x 8.1 in.)
12.5 kg (27.6 lb)
15.1 kg (33.3 lb)
120/230 VAC, 50/60 Hz
(48.6 x 30.9 x 10.8 in.)
20 kg (44.1 lbs)
26 kg (57.3lbs)
120/230 VAC, 50/60 Hz
(54.3 x 33.5 x 10.7 in.)
32 kg (70.5 lbs)
37 kg (81.6 lbs)
120/230 VAC, 50/60 Hz
(W x H x D)
Net Weight
Gross Weight
Electric Ratings
Bosch Security Systems, Inc.
User's Manual
1209.6 x 680.4 mm
F.01U.134.499 | 2.0 | 2012.10
38
en | Technical Specifications
F.01U.134.499 | 2.0 | 2012.10
Bosch High Performance HD LED Monitors
User's Manual
Bosch Security Systems, Inc.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601
U.S.A.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2012
Download PDF

advertising