Watch instruction manual

Watch instruction manual
European Union Directives Conformance Statement
Hereby, CITIZEN WATCH CO., LTD., declares that this H15 is
in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
You can view your product’s Declaration of Conformity (DoC) to Directive
1999/5/EC (the R&TTE Directive) at Citizen Watch global site:
“http://www.citizenwatch-global.com/ ”
“Service & Support”
RF Exposure Information according to 2.1091/2.1093/OET bulletin 65
Radio frequency radiation exposure Information:
The radiated output power of the device is for below the FCC radio frequency
exposure limits.
(i)
FCC statements
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference
that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1)l’appareil ne doit pas produire de brouillage, et
(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
(ii)
Thank you for your purchase of this Citizen watch.
Before using the watch, read this instruction manual carefully to ensure correct
use.
After reading the manual, store it in a safe place for future reference.
Be sure to visit the Citizen website at http://www.citizenwatch-global.com/ . Here
you will find a variety of information such as electronic setting guides, answers to
frequently asked questions, Eco-Drive recharging information and more.
To check the movement number
Engraving position example
A case number—4 alphanumeric characters
and 6 or more alphanumeric characters—is
engraved on the case back. (Figure on the right)
The first 4 characters of the case number
represent the movement number of the watch.
In the example on the right, “
” is the The engraving position may differ
movement number.
depending on watch model.
1
Safety precautions — IMPORTANT
This manual contains instructions that should be strictly followed at all times
not only for optimal use, but to prevent any injuries to yourself, other persons or
property. We encourage you to read the entire booklet (especially, pages 88 to
100) and understand the meaning of the following symbols:
■ Safety advisories are categorized and depicted in this manual as follows:
DANGER
Highly likely to cause death or serious injury
WARNING Can cause serious injury or death
CAUTION Can or will cause minor or moderate injury or damage
■ Important instructions are categorized and depicted in this manual as follows:
Warning (caution) symbol followed by instructions that should be
followed or precautions that should be observed.
Warning (caution) symbol followed by prohibited matters.
2
Before using this watch
After unpacking, the following must be done before using the watch:
• Checking the power reserve
see page 16
For optimal performance, ensure your watch is fully charged prior to use. Refer
to pages 10 to 15 for charging procedures and times.
• Setting the correct time
The time may be adjusted either manually (see pages 64 to 69), or by
receiving time information when connected with iPhone, a mobile digital device,
using the app available from the App Store (see page 47).
This watch has a rechargeable cell which is
charged by exposing the dial to light.
Expose the dial to direct sunlight regularly to
charge the watch.
For details of charging, see pages 10 to 15.
3
Before using this watch
Band adjustment
We do not recommend attempting to adjust the watch band yourself. Special
expertise and experience is required for proper adjustment. If not adjusted
correctly, the band may become detached leading to an injury or loss of your watch.
(Some retailers may supply a band adjustment tool with your purchase).
For band adjustment, we recommend you consult the retailer where the watch was
purchased or your nearest Authorized Citizen Service Center.
Some repair shops may charge a nominal fee for adjustment if the watch was not
purchased directly from them.
Protective stickers
Be sure to remove any protective stickers that may be on your watch (case back,
band, clasp, etc.).Otherwise, perspiration or moisture may enter the gaps between
the protective stickers and the parts, which may result in a skin rash and/or
corrosion of the metal parts.
How to use a specially designed crown/push button
Some models are equipped with a specially designed crown and/or push button(s)
to prevent accidental operation. Please refer to the following chart for use.
4
Before using this watch
Screw down crown and screw down push button
Unlock the crown prior to operate your watch.
Unlock
Lock
Screw down
crown
Rotate the crown
counterclockwise until it
releases from the case.
Push the crown in to the
case. With gentle pressure
towards the case, rotate the
crown clockwise to secure
it to the case. Be sure to
tighten firmly.
Screw down
push button
Rotate the locking screw
counterclockwise, and
loosen until it stops.
Rotate the locking screw
clockwise, and tighten
firmly.
Recessed buttons
Press the button with a narrow-tipped object such
as a wooden toothpick.
5
Table of contents
Features....................................8
Component identification..........9
Charging your watch............... 10
Checking the current power
reserve................................ 16
Changing the mode................ 18
Before connecting to iPhone... 24
Registering (Pairing) your iPhone [PR].................................... 35
When you want to update the app or
register another iPhone............ 36
6
Disconnecting with iPhone..........
[DCT]................................. 41
Connecting to the registered
iPhone [CT]......................... 44
Activating the functions of the
dedicated app...................... 46
Receiving email reception
notification [Email Alert]...... 52
Removing the current
registration......................... 58
Bluetooth 4.0 wireless
technology........................... 60
Adjusting the time and calendar
manually [TME]/[CAL]..... 64
Using local time [L‑TM]......... 70
Using the chronograph
[CHR]................................. 72
Checking and correcting the
reference position [302].... 74
Troubleshooting..................... 78
Resetting the watch —
All Reset.................................... 85
Eco-Drive watch
handling precautions........... 88
Water resistance..................... 92
Precautionary items and
usage limitations................. 95
Information..........................101
Specifications.......................102
7
Features
Connectable with your iPhone using Bluetooth 4.0 through the
dedicated app, and equipped with the following features:
• Automatic Time Sync on page 47 • iPhone Search on page 51
• Incoming Call Alert on page 48 • Email Alert on page 52
• Link Loss Alert on page 50
• Schedule Alert on page 49
Eco-Drive (solar powered): Never needs a new battery. This watch is fueled by
light.
Chronograph: Measure elapsed time up to 60 minutes.
Local time: Easy to see the time for a second time zone, anywhere in the world.
Perpetual calendar: Once set, the date will automatically adjust for months shorter
than 31 days as well as leap years.
* “Eco-Drive” is Citizen’s proprietary technology.
8
Component identification
1
5
Upper right
button ( )
2
6
3
Crown
7
4
Lower right
button ( )
8
The illustrations in this instruction manual may
differ from the actual appearance of your watch.
1 Hour hand
2 Notification indication for connecting
to iPhone (see pages 32)
3 24-hour hand on the upper left sub
dial
4 Second hand/Chronograph second
hand
5 Function hand and function
indications on the upper right sub
dial
• Connection status (see pages 32)
• Power reserve level (see page 16)
• Chronograph minute hand
• Day of the week
6 Minute hand
7 Date indication
8 Mode hand on the lower sub dial
(see page 18)
9
Charging your watch
This watch has a rechargeable cell which is charged by
exposing the dial to light, such as direct sunlight or
fluorescent lamps (refer to pages 12 and 13 for charging
guidelines).
After taking off the watch, put it in a location where the
dial is exposed to bright light, such as by a window.
For optimal performance, be sure to:
• Expose the watch to direct sunlight half a day at least
once a week.
• Avoid leaving the watch in dark places for long periods of time.
Caution
• Do not charge the watch at high temperature (about 60°C (140°F) or higher).
• If the watch is obscured from light by long sleeves frequently, supplemental
charging may be needed to ensure continual operation. Refer to pages 12
and 13.
10
Charging your watch
When the watch reaches a low charge state (insufficient charge warning
function)
When the power reserve becomes low, the second hand
moves once every two seconds. This is the insufficient
charge warning function. Be sure to fully charge your
watch as outlined on pages 12 and 13.
• When the watch is sufficiently charged, the second
hand will move normally.
• If you do not charge the watch for 10 days or longer
after the insufficient charge warning movement has begun, the watch will be
depleted of all power and stop.
Caution
• When in the insufficient charge warning state, the current time and date are
indicated. However, other features and functions of the watch will not be
available for use.
11
Charging your watch Charging time by environment
Below are the approximate times required for charging when exposing the watch
dial to light continuously. Please use this table as a reference only.*
Charging time (approx.)
12
Environment
Illuminance
(lx)
To work for
one day
To start working
To become fully
normally when the cell charged when the cell is
is discharged
discharged
Outdoors (sunny)
100,000
12 minutes
3.5 hours
13 hours
Outdoors (cloudy)
10,000
30 minutes
6.5 hours
30 hours
20 cm (8 inches)
away from a
fluorescent lamp
(30W)
3,000
1.5 hours
15 hours
90 hours
Interior lighting
500
8 hours
80 hours
600 hours
Charging your watch
• To charge your watch, it is recommended to expose the dial to direct sunlight.
Optimal charging is achieved by exposing the dial to direct sunlight outdoors for
a short time each day.
Power reserve in normal use from fully charged without additional charging
With connecting to iPhone
About 8 months*
*
Without connecting to iPhone
About 17 months
When the watch is connected to your iPhone about 6 hours a day and received messages
about 10 times a day, you can use the connecting feature between the watch and your iPhone
about 30 days in 8 months. For details, see page 17.
Caution when connecting to iPhone
• Connecting to iPhone requires a substantial amount of power, especially if receiving many
notifications. Be sure to keep your watch fully charged when utilizing this feature.
• We recommend disconnecting with iPhone when not needed (see page 41).
• Connecting feature does affect battery usage on your iPhone. Be sure to check the charge
level of your iPhone.
13
Charging your watch Power save function
If your watch is not exposed to light sufficient for charging for 30 minutes or more,
the second hand will stop in order to conserve power. Although the second hand is
not moving, the correct seconds are stored in memory.
The power save function cannot be activated manually; it is an automatic feature
only. The power save function does not operate under the following conditions:
• The crown is in position or .
• The current mode is Chronograph [CHR] or Calendar [CAL].
• The second hand is indicating a notification (“MAIL”/ “CALL”/ “LL”).
14
Charging your watch
Canceling the power save function
The power save function is automatically canceled when the watch is exposed to
light sufficient for charging. The second hand will then resume normal movement.
• The power save function will also be canceled if a notification is received from
your iPhone. Note: the watch must be sufficiently charged and the dedicated app
running on your iPhone in order to receive notifications.
• If the watch is in the power save state for long period of time, adjust the time and
date before use through the iPhone connection (see page 47) or manually (see
page 64).
15
Checking the current power reserve
This watch has a power reserve display feature when in [TME], [L‑TM], [PR], [CT],
or [DCT] mode.
Power reserve indication (Function hand on the upper right sub dial)
Without iPhone connection
With iPhone connection
• If the current power reserve is not displayed (the watch is in [CAL] or [CHR]
mode), change the mode (see page 18).
• When connecting to iPhone, pay particular attention to the power reserve to
ensure sufficient power is available.
16
Checking the current power reserve
The power reserve level
Level
3
2
1
With connecting to iPhone within 6 hours a day
Up to 10 days Up to 15 days
Up to 5 days
Without connecting to iPhone
Up to 3 months Up to 5 months Up to 2 months
Approximate
duration of Power reserve
indication at is sufficient for
this level
all features and
Power reserve is
sufficient for all
operations at this
functions. Optimal level.
performance is
achieved at this
level.
*
Power reserve is
getting low. The
watch should be
fully charged to
ensure optimal
performance.
0
7 months*
Power reserve
is not sufficient
for normal
operation. The
watch must be
fully charged.
Charge the watch immediately.
When the power reserve is at level “0”, basic watch functions can be used. However, registering
(see page 35) and connecting to iPhone (see page 44) are not available. If the watch is
connected to your iPhone and the power reserve becomes at level “0”, the connection will be
disconnected automatically.
17
Changing the mode
This watch features eight different modes (functions). Change the mode by rotating
the mode hand on the lower sub dial before using each mode.
1 Pull the crown out to position .
The second hand moves to indicate the 30 seconds
position.
The second hand indicates the 30 seconds position.
18
Changing the mode
2 Rotate the crown to select a mode.
• Each time you rotate the crown, the mode hand on the lower sub dial moves.
Rotate the crown until the mode hand indicates the mode you wish to use.
Proper location
Improper location
Ex. When selecting [L‑TM]
• You may turn the mode hand either clockwise or counterclockwise.
• The hands/indications function differently in each mode. See pages 20 to
23 for more details of each mode and the functions of the hands/indications
in each mode.
3 Push the crown in to position to finish the procedure.
19
Changing the mode
Mode indications and functions
24-hour hand
Function hand
Time — [TME]
• Normally, use the watch in [TME] or
[L‑TM] mode.
[TME]
The currently set time is displayed.
• The function hand on the upper
right sub dial indicates the power
reserve in this mode.
Mode hand
20
Changing the mode
Pairing/Connecting/Disconnecting of iPhone — [PR]/[CT]/[DCT]
[PR] (Pairing)
[CT] (Connect)
[DCT] (Disconnect)
Select this only when you
want to connect (pair/
register) the watch to your
iPhone for the first time.
(See page 35.)
Select this mode when
you want to connect your
watch to your iPhone after
initial pairing. (See page
44.)
Select this when you
disconnect the watch from
your iPhone. (See page
41.)
• Time indication is same as either [TME] or [L‑TM].
21
Changing the mode
Local time — [L‑TM]
[L‑TM]
Select this to display the time of
another area (local time). (See page
70.)
• The 24-hour hand on the upper left
sub dial, date and day of the week
display local time.
• The function hand on the upper
right sub dial indicates the power
reserve in this mode.
22
Chronograph — [CHR]
[CHR]
Select this when you want to use the
chronograph. (See page 72.)
• The second hand: Indicates the
chronograph seconds.
• The function hand on the upper
right sub dial: Indicates the
chronograph minutes.
• The hour, minute and 24-hour
hands will continue to reflect the
time set in [TME] or [L‑TM] mode.
Changing the mode
Calendar — [CAL]
The reference position — [302]
[CAL]
[302]
Select this to display the calendar. (See
page 64.)
• The second hand: Indicates the
year/month.
• The function hand on the upper
right sub dial: Indicates the day of
the week.
• The hour, minute and 24-hour
hands will continue to reflect the
current time set in [TME] mode.
The current reference position of each
hand/indication is indicated. (See page
74.)
23
Before connecting to iPhone
This watch communicates with iPhone
through the connection of Bluetooth 4.0,
which is featured Bluetooth Low Energy
(BLE) power-saving technology.
It is required for connection to install
and start up a dedicated app “CITIZEN
ECO-DRIVE Proximity” on a compatible
iPhone.
The flow for connection is shown as
follows.
• Screen in this manual may differ from
the actual app.
Install the dedicated app
Start up the app
Registration/Pairing
Connection
Disconnection
24
Before connecting to iPhone
iPhone connectable with this watch
To check the latest information on compatible iPhone and iOS, visit the following
sites:
• Citizen Watch global site: “http://www.citizenwatch-global.com/ ”
“Service & Support”
Set the mode to [DCT] (see page 41) to use this watch as a standard one in
places such as an airplane, where electronic devices are limited to use.
iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc.
25
Before connecting to iPhone
Functions available with the connection
Automatic adjustment of time and calendar [Time Sync]
The watch adjusts time and calendar automatically using time info provided from
the iPhone.
Time info
ACT
Cellular phone network
26
The second hand points “ACT”
while receiving time info from
iPhone.
Before connecting to iPhone
Incoming call notification [Incoming Call]
Incoming call alert comes to the watch since iPhone’s call reception.
CALL
Incoming Call
Incoming call info
Cellular phone network
The watch vibrates twice
and the second hand points
“CALL” as it receives
incoming call info.
27
Before connecting to iPhone
Schedule notification [Schedule Alert]
The watch receives schedule notification from the built-in Calendar app on your
iPhone, corresponding to the setting of the app.
MAIL
Schedule
notification
Schedule notification info
The watch vibrates twice
and the second hand
points “MAIL” as it receives
notification info.
28
Before connecting to iPhone
Email reception notification [Email Alert]
Email alert comes to the watch since iPhone’s email reception to the account set on the
dedicated app.
MAIL
Email
notification
Cellular phone network
Email notification info
The watch vibrates twice
and the second hand
points “MAIL” as it receives
notification info.
29
Before connecting to iPhone
Link Loss alart (Bluetooth disconnection notification) [Bluetooth Link Loss Alert]
The watch notifies iPhone’s disconnection due to their distance.
Bluetooth connectable range
5 m (16-1/2 feet) to 10 m
(33 feet)
LL
The watch vibrates twice and
the second hand points “LL” as
it detects disconnection.
30
Before connecting to iPhone
iPhone search [iPhone Search]
The watch sends signals to the registered iPhone within the connectable range.
• This function is also available when they are disconnected.
Bluetooth connectable range
5 m (16-1/2 feet) to 10 m (33 feet)
ACT
The iPhone sounds (depending
on the setting) as it receives the
signal.
The second hand points “ACT” as
it starts to send signals.
31
Before connecting to iPhone
Connection and notification indication on the watch
• Because the watch vibrates gently for the notification, it is recommended to check
the vibration in advance. (See page 34.)
Notification position of the
second hand
CALL Incoming phone
Connection status (the
function hand on the upper
right sub dial)
MAIL
ON
Connected
OFF
Not connected.
calls
32
Emails and schedule
info
LL
Disconnection
(Link Loss)
ACT
The watch is waiting
to be connected
or processing
communication
(Activation)
• Since the actual pointing
position of the hand
varies depending on
the amount of charge,
distinguish “ON” and
“OFF” by the area the
hand points.
Before connecting to iPhone
• The maximum connectable range is about 10 m (33 feet). Connectable range may
be shorter due to obstacles such as walls.
Do not block the watch with your body such as your arm.
• When [▶0◀], [CHR] or [CAL] mode is selected, only vibration gives you
notification. The indication by the second hand will be made with another
vibration when you change the mode to [TME], [L‑TM], [PR] or [CT].
You can check how the watch vibrates in advance. (See page 34.)
• When the watch receives a new info while the second hand indicates a
notification type, the hand’s indication is updated corresponding to the new info.
Stopping the notification indication
Press and hold either the lower right button or upper right button for two
seconds while the second hand indicates a notification, and the second hand stops
the notification indication and return to the normal movement.
33
Before connecting to iPhone
Testing the vibration of the watch
1 Change the mode to [CT]. (See page 18.)
2 Pull the crown out to position .
3Press and release either the lower right button
or upper right button
.
The watch starts vibrating.
• The vibration is different from the actual notification
vibration.
4 Push the crown in to position .
5 Change the mode to either [TME] (or [L‑TM]) to
finish the procedure. (See page 18.)
34
Registering (Pairing) your iPhone [PR]
When connecting the watch and your iPhone for the first time, mutual registration
(pairing) is required.
Before registration
• For registration, you have to operate both the watch and the iPhone.
• Be sure that the watch and the iPhone are charged enough. Especially, check
the power reserve indication of the watch (see page 16) and charge it before
registration if the power reserve level is “1” or “0”.
• The watch and the iPhone is connected after registration.
• You cannot register two or more iPhones.
Continued on the next page
35
Registering (Pairing) your iPhone [PR]
Connection after registration
The registered iPhone cannot be registered again. Use Connect (page 44) and
Disconnect (page 41) to activate/deactivate connection in everyday use.
When you want to update the app or register another iPhone
Remove the current registration and execute registration anew. (See page 58.)
Registering the iPhone
The iPhone registration on the watch must be completed within about 2 minutes. If
about 2 minutes have passed before finishing the registration, the watch returns to
the normal movement.
• The installed app is shown as the icon.
• After registration, set the functions to “ON” on the app’s screen on
the iPhone. (See page 46)
App icon
36
Registering (Pairing) your iPhone [PR]
<Operation on iPhone>
1 Download and install the dedicated app “CITIZEN
ECO-DRIVE Proximity” from App Store.
2 Tap the app icon to start up the app.
3 Slide the switch of “Scan” to “ON” on the app’s
screen.
Scan
ON
The iPhone starts to detect the watch.
• Do not change the app screen until the registration is
completed.
• When “Waiting for Reconnection” is shown, slide
the switch to “OFF”.
• When the iPhone’s Bluetooth setting is “OFF”, an
activation dialog appears.
Continued on the next page
37
Registering (Pairing) your iPhone [PR]
<Operation on the watch>
4 Pull the crown out to position .
The second hand moves to indicate the 30 seconds
position.
5 Rotate the crown to change the mode to [PR].
6 Push the crown in to position .
The second hand moves to
indicate the “ACT” position,
allowing the watch to be detected
for two minutes.
• When registration was finished,
the second hand returns to
normal without indicating
[ACT].
Use Connect (page 44) to
activate connection.
38
Registering (Pairing) your iPhone [PR]
<Operation on iPhone>
7 Tap “Pair” when the permission request of
Bluetooth connection appears on the app’s screen.
Registration completes successfully when “Proximity
Connect” appears on the screen.
Proximity Connect
ON
• It may take up 20 to 30 seconds to complete the
registration.
Continued on the next page
39
Registering (Pairing) your iPhone [PR]
<Operation on the watch>
The function hand on the upper right
sub dial points the area shown on the
right (“ON” area) when registration
completes successfully and the watch is
connected with the iPhone.
“ACT” indication ends and the second
hand returns to second indication.
8 Change the mode to either [TME] (or [L‑TM]) to
finish the procedure. (See page 18.)
40
Disconnecting with iPhone
[DCT]
You can close the connection with the iPhone by using the watch’s button in the
following cases:
• When the function hand on the upper right sub dial indicates “ON” area.
• When the second hand indicates the second.
(While the second hand indicates a notification type,
stop the notification indication by pressing and holding
either the lower right button or upper right button
for two seconds.)
1 Change the mode to [DCT]. (See page
18.)
The connection is closed and the function
hand on the upper right sub dial indicates
“OFF” area.
Function hand
• In this case, the switch name changes
on the upper
from “Proximity Connect” to “Waiting right sub dial
for Reconnection”.
Continued on the next page
41
Disconnecting with iPhone [DCT]
2 Change the mode to either [TME] (or [L‑TM]) to finish the procedure.
(See page 18.)
When operating from the iPhone
You can close the connection from the iPhone.
1 Set “Proximity Connect” to “OFF”.
The switch name changes to “Scan” soon.
Proximity Connect
42
OFF
Scan
ON
Disconnecting with iPhone [DCT]
Checking the connection status on the app screen
While connected
Disconnected
Proximity Connect
ON
Only the following operations are
available:
• Reconnection with the operation on
Shown when the disconnection
the watch (see page 44)
is done by the watch operation or
intentionally. In this case, you cannot • Searching for your iPhone (see page
51)
register the iPhone.
Waiting for Reconnection
ON
Scan
ON
Shown when the disconnection is
done by the app operation.
Scan
App in rest
You can use the functions with the
setting “ON”.
OFF
The app does not consume the iPhone
battery.
It is recommended to stop or quit the
app to save the batteries of the watch
and/or the iPhone when leaving them
disconnected for a long time.
• The Bluetooth setting on the iPhone
remains “ON” even when “Scan” is
set to “OFF” or the app is not active.
43
Connecting to the registered iPhone
[CT]
You can reconnect with the registered iPhone again in the following cases:
• When the function hand on the upper right sub dial indicates “OFF” area.
• When the watch mode is set to [TME], [L‑TM], [PR] or [CT].
• When the second hand indicates the second.
(While the second hand indicates a notification type, stop the notification
indication by pressing and holding either the lower right button or upper right
button for two seconds.)
1 Confirm the switch of “Scan” or “Waiting for Reconnection”
is “ON” on the app’s screen.
2Press and release the upper right button
.
The second hand moves to indicate “ACT”. When successfully
connected, the movement of the second hand returns to normal Function hand
and the function hand on the upper right sub dial indicates “ON” on the upper
area.
right sub dial
• It may take up 20 to 30 seconds to complete the reconnection.
44
Connecting to the registered iPhone [CT]
You can also reconnect the watch and the iPhone by
changing the mode of the watch.
1 Change the mode to [CT]. (See page 18.)
The second hand moves to indicate
“ACT”. When successfully connected, the
movement of the second hand returns
to normal and the function hand on the
upper right sub dial indicates “ON” area.
Function hand
• It may take up 20 to 30 seconds to
on the upper
complete the reconnection.
right sub dial
2 Change the mode to either [TME] (or [L‑TM]) to
finish the procedure. (See page 18.)
45
Activating the functions of the dedicated app
You can set functions to “ON” or “OFF” on the app’s screen during connection. For
the details of each function, refer to the pages shown below.
Function
Time Sync
Incoming Call
Schedule Alert
Email Alert
Bluetooth Link Loss
Alert
iPhone Search
46
Page
Description
47 Sends time/calendar info.
48 Sends notification of incoming call.
49 Sends notification of schedule from the built-in Calendar
app on the iPhone.
52 Sends notification of email reception for the account
registered to the app.
50 Notifies when the connection is interrupted.
51
Makes the iPhone sounding to answer the signal from
the watch.
Activating the functions of the dedicated app
Automatic adjustment of time and calendar [Time sync]
When you set “Time Sync” to “ON”, the watch receives the time info (year, month,
date, day, hour, minute, second) from the iPhone and adjust the time following it
each time they are connected.
Time Sync
ON
• The time on the watch is adjusted automatically each time they are connected
and the time setting of your iPhone is changed during connection.
• The local time (see page 70) is also adjusted based on the time difference set as
the time is adjusted.
• If the watch cannot receive the time information from the iPhone, a message will
appear on the iPhone.
• This watch keeps ±15-second monthly accuracy even if no time info is received.
Receiving the time info manually
You can receive the time info manually by pressing and holding the lower right
button for 2 seconds. Time info reception is executed when the mode is [TME],
[L-TM], [PR] or [CT] and the second hand indicate second.
47
Activating the functions of the dedicated app
Receiving incoming call notification [Incoming Call]
When you set “Incoming Call” to “ON”, the watch receives incoming call info from
the iPhone connected.
Incoming Call
ON
When receiving incoming call info
The watch vibrates twice and the second hand points “CALL”.
• To return the second hand to normal movement, press and hold either the lower
right button or upper right button for two seconds.
48
Activating the functions of the dedicated app
Receiving schedule notification [Schedule Alert]
When you set “Schedule Alert” to “ON”, the watch receives schedule notification
from the iPhone connected.
Schedule Alert
ON
• For schedule alert setting, set it on the alert setting of the iPhone’s Calendar.
When receiving schedule notification
The watch vibrates twice and the second hand points “MAIL”.
• To return the second hand to normal movement, press and hold either the lower
right button or upper right button for two seconds.
49
Activating the functions of the dedicated app
Receiving the leaving-iPhone alert (Bluetooth disconnection notification)
[Bluetooth Link Loss Alert]
When you set “Bluetooth Link Loss Alert” to “ON”, the watch alerts when the
communication with the iPhone is closed due to the iPhone location or other
unintentional reasons.
Bluetooth Link Loss Alert
ON
• No notification is sent to the watch if the iPhone and other Bluetooth devices are
disconnected.
When the iPhone is disconnected
The watch vibrates twice and the second hand points “LL”.
The watch automatically tries to reconnect with the iPhone once (The second hand
points “ACT”.), but close connection if the reconnection failed and the function
hand points the “OFF” area.
• To return the second hand to normal movement, press and hold either the lower
right button or upper right button for two seconds.
50
Activating the functions of the dedicated app
Searching for the iPhone [iPhone Search]
When you set “iPhone Search” to “ON”, you can send signals to the registered
iPhone in the connectable range with the watch.
When receiving the signal, the iPhone sounds depending on its setting.
iPhone Search
ON
Locating your iPhone using sounds
Press and release both the lower right button and the upper right button
simultaneously when the mode of the watch is [TME], [L-TM], [PR] or [CT] and
the second hand indicate second.
The second hand points “ACT” and the signals are started to send.
• It may take up 20 to 30 seconds to start sounding.
• When the switch of “Scan” or “Waiting for Reconnection” is “ON”, the signals
can be sent to the disconnected iPhone.
• iPhone sounds even when the muting switch is activated or the sound volume is
set to 0.
• When the earphones are plugged, iPhone does not sound.
51
Receiving email reception notification [Email Alert]
When you set “Email Alert” to “ON”, the watch receives email notification at email
arrival to the account set on the dedicated app “CITIZEN ECO-DRIVE Proximity”.
Email Alert
ON
• You can enter up to five mail accounts.
• This function does not notify the receptions of iPhone’s Mail and SMS.
• This app only check existence of new unread mails on mail servers. You cannot
browse mails on it.
When receiving email reception notification
The watch vibrates twice and the second hand points “MAIL”.
• To return the second hand to normal movement, press and hold either the lower
right button or upper right button for two seconds.
52
Receiving email reception notification [Email Alert]
Setting the mail account
To send the mail reception info to the watch, you have to set mail accounts on the
dedicated app.
• This function is only available for accounts whose mail servers are compatible
with IMAP.
• Prepare IMAP mail account, IMAP mail server addresses for sending and
receiving, user name and password before setting. Consult your mail service
provider for the information required.
• You can set the mail accounts before connection.
1 Tap the app icon to start up the app and tap “Mail Accounts”.
Mail Accounts
Continued on the next page
53
Receiving email reception notification [Email Alert]
2 Tap “+” to add an account.
Back
Mail Accounts
• Tap an existing account to edit its setting.
3 Select an IMAP mail service you use on the list and tap its name.
• If your mail service is not listed, tap “Other”.
4 Enter items required and tap “Done”.
Cancel
IMAP Setting
Done
Connection test to the mail server starts immediately and the mail account
entered is verified. When the test ends successfully, the screen of step 2 appears
again.
• When the test fails, a failure message appears. Enter items required again.
54
Receiving email reception notification [Email Alert]
5 Repeat steps 2 to 4 to set other accounts.
• The accounts set are listed under “Email Alert”.
Email Alert
ON
Account 1
ON
Account 2
ON
6 Tap “Back” to finish the setting.
To delete an existing mail account from the app
Tap “Delete Account” on the screen of an existing account.
• All the settings are deleted as the dedicate app is uninstalled on the iPhone.
55
Receiving email reception notification [Email Alert]
Selecting accounts for which mail reception notification is sent
You can select accounts for mail reception notification by setting them to “ON” or
“OFF”.
1 Tap the app icon to start up the app.
2 Slide the switch for each account under “Email Alert” to “ON” or “OFF”.
Email Alert
Account 1
Account 2
56
ON
OFF
ON
Receiving email reception notification [Email Alert]
Adjusting the interval of mail reception notification
You can adjust the interval of mail reception notification.
• The interval set is common to all mail accounts.
1 Tap the app icon to start up the app and tap “Mail Accounts”.
2 Tap “Polling Interval”.
Polling Interval
3 Tap the interval you prefer.
• Increased use of this feature may affect battery life.
To save power consumption, decrease the polling interval to a less frequent
setting of 15 minutes or more.
4 Tap “Mail Accounts”
“Back” to finish the setting.
57
Removing the current registration
In the following cases, you must remove the registration information on both
the watch and the iPhone:
• When registration information was accidentally removed on the watch or iPhone.
• When you want to register another iPhone.
• When the app was updated or downloaded again.
• When the connection cannot be activated even after executing the correct
connection steps after registration.
Removing the registration from the iPhone
Follow the steps below to remove the information of the watch on the iPhone.
1 Tap “Settings” and open “Bluetooth” setting on the iPhone.
2 Delete “Eco-Drive Proximity”, the information of the watch, on the
“DEVICES” list.
• The information of the watch has already been deleted if “Eco-Drive
Proximity” is not found on the list.
58
Removing the current registration
Removing the registration from the watch
Follow the steps below to remove the information of the iPhone on the watch.
You can remove it in the following cases:
• When the function hand on the upper right sub dial indicates “OFF” area.
• When the watch mode is set to [TME], [L‑TM], [PR] or [CT].
• When the second hand indicates the second. (While the second hand indicates a
notification type, stop the notification indication by pressing and holding either
the lower right button or upper right button for two seconds.)
1 Press and hold the upper right button
for seven seconds or more.
The second hand moves 360° around and returns to normal.
59
Bluetooth 4.0 wireless technology
Bluetooth is a type of wireless communication technology used over distances of
about 5 m (16-1/2 feet) to 10 m (33 feet) from handheld information products such
as smartphones, head sets and game gadgets.
• This watch supports the Bluetooth 4.0 utilizing the electricity saving technology,
Bluetooth 4.0 (Bluetooth Low Energy).
• The communication distance using Bluetooth may become smaller when
obstacles such as walls exist. It may be particularly affected by the human body
such as your arms.
60
Bluetooth 4.0 wireless technology
The Bluetooth communication technology of this watch may not be usable
depending on the law of the country. For a list of countries where it can be used,
visit the following web page. If using this watch in a country other than those listed,
you may be punished by the law of the country. Please confirm before use.
Citizen Watch global site: “http://www.citizenwatch-global.com/ ”
& Support”
“Service
Within the frequency band (2.4 GHz) used by this watch, local area wireless
stations (wireless stations requiring a license) for identifying the mobile objects
used on the production lines of factories, etc. in addition to industrial, scientific
and medical applications such as microwaves, specific low electric power wireless
stations (wireless stations not requiring a license), and amateur radio stations
(wireless stations requiring a license) are operated.
Continued on the next page
61
Bluetooth 4.0 wireless technology
• Please make sure that neither local area wireless stations for identifying mobile
objects, specific low electric power wireless stations, nor amateur radio stations
are being operated nearby before using this watch.
• Should any case of harmful radio wave interference from this watch to local
area wireless station for identifying mobile objects occur, please stop using
Bluetooth 4.0 immediately and consult the nearest Authorized Citizen Service
Center for necessary steps to avoid interference.
• Should any trouble including other cases of harmful radio wave interference
from this watch to specific low electric power wireless stations or amateur radio
stations, please consult the nearest Authorized Citizen Service Center.
• The connectable distance for the Bluetooth 4.0 is approximately 10 m (33 feet) in
an ideal location. Placing the transmitter and receiver behind reinforced concrete
or metallic walls may block radio waves and disrupt sufficient communication.
The communication distance may shorten depending on the environment where
this watch is used.
62
Bluetooth 4.0 wireless technology
• Placing this watch and the following electronic devices within close range
may cause problems such as malfunction due to radio wave interference and
production of noise.
- Devices utilizing the 2.4 GHz frequency range including wireless LAN,
microwaves, and digital cordless phones. Radio wave interference may cause
cutting off of the sound.
- Audio video equipment with an antenna input terminal including radios, TVs,
video recorders, and satellite tuners. Noise may occur in the sound and image.
• Due to the use of radio waves, messages transmitted through this watch may be
eavesdropped by third parties intentionally or accidentally. Do not use this watch
for important communication or any communication involving human lives.
63
Adjusting the time and calendar manually [TME]/[CAL]
Adjusting the time — [TME]
1 Change the mode to [TME]. (See page 18.)
2 Pull the crown out to position .
The second hand rotates to indicate the current time.
3Press and release the lower right button
upper right button
.
or
The second hand moves to indicate the 0 seconds
position.
64
Adjusting the time and calendar manually [TME]/[CAL]
4 Rotate the crown to adjust the time.
• You can adjust the time in one minute increments.
• The hour and minute hands and 24-hour hand on the upper left sub dial move
in conjunction with one another.
• When adjusting the time, be sure to pay particular attention to the 24-hour
hand to ensure AM or PM time is set properly.
• If you spin the crown quickly a few times, the hand will move continuously.
To stop the rapid movement, rotate the crown in either direction.
5 Push the crown in to position in accordance with a reliable time
source to finish the procedure.
This completes manual time adjustment.
65
Adjusting the time and calendar manually [TME]/[CAL]
Adjusting the Calendar — [CAL]
• The hour and minute hands and 24-hour hand on the upper left sub dial will
indicate the time set in [TME] mode.
• While in [CAL] mode, notifications will be through watch vibration only. Visual
notification by the second hand occurs only in [TME], [L‑TM], [PR] or [CT] mode.
1 Change the mode to [CAL]. (See page 18.)
2 Pull the crown out to position .
The second hand rotates to indicate the current month
and leap year set in memory, while the function hand
on the upper right sub dial rotates to indicate the
current day of the week set in memory.
3 Rotate the crown clockwise to adjust the month
and leap year.
• See pages 68 and 69 for instructions on how to read
the month and leap year setting.
• Each time you rotate the crown, the second hand
moves by one step.
66
Adjusting the time and calendar manually [TME]/[CAL]
4Press and release the upper right button
.
The function hand on the upper right sub dial will move slightly to indicate that
the date can be set.
5 Rotate the crown to adjust the date.
• Each time you rotate the crown fully clockwise, the function hand on the
upper right sub dial will rotate five times and the date will advance by one day.
When you rotate the crown fully counterclockwise, it will go back by one day.
• If you spin the crown quickly a few times, the date will move continuously. To
stop the rapid movement, rotate the crown in either direction.
6Press and release the upper right button
.
The function hand on the upper right sub dial will move slightly to indicate that
the day of the week can be set.
7 Rotate the crown to adjust the day of the week.
• Each time you rotate the crown fully clockwise, the day of the week will
advance by one day. When you rotate the crown fully counterclockwise, it will
go back by one day.
• When pressing and releasing the upper right button after setting the day of
the week, you can return to setting the month and leap year.
Continued on the next page
67
Adjusting the time and calendar manually [TME]/[CAL]
8 Change the mode to [TME] (or [L‑TM]) to finish the procedure. (See
page 18.)
• The date will change at approximately 0:00 a.m. (midnight). This process takes
approximately 5 seconds to complete.
Month and year indications
The month and leap year are indicated
by the position of the second hand when
in [CAL] mode. When set correctly, the
watch will be automatically adjusted for
months shorter than 31 days as well as
for leap years.
The month and leap year are indicated
by the hour and minute indices.
The years since the last leap year are
indicated by the first three minute
indices past each hour.
68
Nov.
Dec.
Oct.
Jan.
Sept.
Feb.
Aug.
Mar.
July
Apr.
June
May
Adjusting the time and calendar manually [TME]/[CAL]
Each minute mark denotes the
number of years since the last
leap year.
Leap year
1st year since leap year
2nd year since leap year
3rd year since leap year
In the example above, the second hand indicates April
and 2 years since the last leap year.
Quick reference chart for number of years passed since leap year
Indication of the second hand
Leap Year/Years since leap year
Actual year
Hour marker
Leap year
2012, 2016, 2020
1st min. marker
1st year
2013, 2017, 2021
2nd min. marker
2nd year
2014, 2018, 2022
3rd min. marker
3rd year
2015, 2019, 2023
69
Using local time
[L‑TM]
Indicating local time (secondary time)
The watch can indicate the time of another time zone (known as local time) using
[L‑TM] mode.
1 Change the mode to [L‑TM]. (See page 18.)
The currently set local time (secondary time) is
displayed.
• The hour, minute, 24-hour, date and day of week are
displayed.
• If a local time (secondary time) has not been set, the
time reflected will be that of the time set in [TME]
mode.
• If you receive the time info while in [L‑TM] mode, both
the time set in [TME] and [L‑TM] mode are adjusted.
70
Using local time [L‑TM]
Setting the local time
The setting range of the time difference from the time set in [TME] mode is ±27
hours in 15-minute increments.
1 Change the mode to [L‑TM]. (See page 18.)
2 Pull the crown out to position .
3 Rotate the crown to set the time in 15-minute increments.
• When you rotate the crown quickly a few times, the hands will move
continuously. To stop the rapid movement, rotate the crown in either
direction.
4 Push the crown in to position to finish the procedure.
71
Using the chronograph
[CHR]
The 60-minute chronograph can indicate a maximum of 59’ 59”.
• While in [CHR] mode, notifications will be through
watch vibration only. Visual notification by the second
hand is disabled in this mode and will be made with
another vibration when you change the mode to [TME],
[L‑TM], [PR] or [CT].
1 Change the mode to [CHR]. (See page 18.)
The second hand moves to indicate the 0 seconds
position to enable you to measure time.
2 Use the chronograph.
• See page 73 for the method of measurement.
3 Change the mode to either [TME] (or [L‑TM]) to
exit chronograph [CHR] mode. (See page 18.)
72
Using the chronograph [CHR]
Upper right button
Start/Stop/Restart
measurement.
Second hand:
This indicates the
elapsed seconds
while using the
chronograph.
:
The chronograph minute
hand:
This indicates the elapsed
minutes (up to 60) while
using the chronograph.
Lower right button : Reset
• Press and release this
button to reset the
chronograph after timing.
• After one hour of continuous chronograph operation, the chronograph
automatically stops and is reset. Pulling out the crown will also stop and reset the
chronograph.
• The time reflected by the hour and minute hands and 24-hour hand on the upper
left sub dial will be that of the time set in [TME] or [L‑TM] mode.
73
Checking and correcting the reference position
[302]
If the time or date is not shown correctly even after proper reception of the time
info, check whether the reference position is correct.
74
Correct reference positions
What is the reference position?
The base position of all hands and date to
properly indicate the various functions of this
watch.
• Position of the hour hand: 12:00
• Position of the minute hand: 12:00
• Position of the second hand: 12:00
• Position of the 24-hour hand on the upper
left sub dial: 24:00
• Position of date: midway between 31 and 1
• Position of the function hand on the upper
right sub dial: directed towards 6:00
• If the hands and/or date do not reflect the correct reference position, the
time, date, and other indications will not be displayed accurately, even if you
synchronize the time with your iPhone.
Checking and correcting the reference position [302]
Checking the reference position
Check whether the reference position of each hand and indication is accurate.
1 Change the mode to [302]. (See page 18.)
The hands and date will rotate to the current reference
positions stored in memory.
2 Check the current reference position.
By referring to the chart on page 74, ensure the
reference position of each hand and the date are
correct.
• If all reference positions are correct, go to step 3
below.
• If some reference positions are incorrect, go to page
76.
3 Change the mode to either [TME] (or [L‑TM]) to
finish the procedure. (See page 18.)
75
Checking and correcting the reference position [302]
Correct the current reference position
Correct each hand and indication to indicate the correct reference position.
1 Change the mode to [302]. (See page 18.)
Each hand and indication indicate the current
reference position.
2 Pull the crown out to position .
This will enable you to correct the reference position.
3Press and release the upper right button
.
Each time you press and release the upper right button
, the active hand will move slightly indicating that
hand (or date) may be set. The order of movement is:
Hour, minute and 24 Date/Function hand
Second hand
return to date/
hour hand
function hand
76
Checking and correcting the reference position [302]
4 Rotate the crown to correct the reference position of the active hand/
indication.
• When you rotate the crown quickly a few times, the hands and indications will
move continuously.
The second hand will move one full rotation, and the other hands and
indications will move until you rotate the crown either clockwise or
counterclockwise.
5 Repeat steps 3 and 4 as required.
6 Push the crown in to position .
7 Change the mode to either [TME] (or [L‑TM]) to finish the procedure.
(See page 18.)
77
Troubleshooting
If you have a problem with your watch, check the table below.
Symptoms
Remedies
Page
Connection with iPhone
16 and 17
Check the power reserve.
Connection is
unsuccessful
• If you cannot solve
your problem with the
remedies shown on
the right, consult the
nearest Authorized
Citizen Service Center.
78
18 to 23
Check the mode of the watch.
Press and hold either the lower right button or
upper right button for two seconds to cancel the
notification indication.
33
Push the crown in to position
−
.
Avoid anything that will block out the radio wave
or generate noise.
−
Check the versions of your iPhone and iOS.
25
Troubleshooting
Symptoms
Connection is
unsuccessful
• If you cannot solve
your problem with the
remedies shown on
the right, consult the
nearest Authorized
Citizen Service Center.
Remedies
Page
Restart the dedicated app.
24
Check the Scan status.
43
Check the Bluetooth setting on your iPhone.
Remove the current registration and register again.
−
58, 59,
35 to 40
Continued on the next page
79
Troubleshooting
Symptoms
Remedies
Page
Connection with iPhone (continued)
Check the connection status (“ON”, “OFF”).
Check the power reserve.
Not notified within
connectable distance
Ensure your iPhone is not being obscured such as
by being in a pocket or purse.
When in [302], [CHR] or [CAL] mode, notification
of iPhone is through vibration only. The visual
indication by the second hand is available only in
[TME], [L‑TM], [PR] or [CT] mode.
Turn “ON” of the functions on the app’s screen.
Registration is
unsuccessful
80
32
16 and 17
−
33
46 to 51
Check the setting of mail accounts is “ON” on the
app’s screen.
56
Remove the current registration and register again.
58, 59,
35 to 40
Troubleshooting
Symptoms
Time info cannot be
obtained automatically.
Remedies
Page
Check if your iPhone is in communication distance
(5 m / 16-1/2 feet to 10 m / 33 feet) and avoid
obstacles between the watch and the iPhone.
−
Check the connection status (“ON”, “OFF”).
32
Check if the watch is ready to receive the time info
(the mode is set to [TME], [L‑TM], [PR] or [CT]
and the crown is in position ).
18 to 23
Check the status of your iPhone (charging or sleep
mode).
−
Continued on the next page
81
Troubleshooting
Symptoms
Remedies
Page
Connection with iPhone (continued)
iPhone does not sound
using iPhone Search.
The switch of “Scan” on the app is “OFF” or the
app is not active on the iPhone.
Your iPhone is not in communication distance
(5 m / 16-1/2 feet to 10 m / 33 feet).
Earphones are plugged in.
Your iPhone is not registered yet.
This may occur as a result of a pairing (registration)
or connection failure. Pull the crown out to
The second hand remains position or , then push it in to position . If
this does not work, leave the watch for about two
indicating “ACT” and
does not move at all.
or more minutes.
If the second hand still does not move, consult the
nearest Authorized Citizen Service Center.
82
51
31
51
35 to 40
−
Troubleshooting
Symptoms
Remedies
Page
The hands rotate rapidly
soon after you expose
the watch to light
sufficient for charging
(out of a case or pocket,
from under a shirt
sleeve, etc.).
The power save function is canceled. Wait until the
current time is displayed.
14 and 15
The hands move in an
unexpected direction.
Check the current mode.
18 to 23
The second hand does
not move.
Check the current mode. The second hand does
not move in some modes.
Press and release either the lower right button
or upper right button to cancel the notification
indication.
18 to 23
The second hand moves
once every two seconds.
This indicates low power. Fully charge the watch.
10 to 15
Movement of a hand seems strange
−
Continued on the next page
83
Troubleshooting
Symptoms
Remedies
Page
The time and/or date is incorrect.
Change the mode to [TME].
The indication of
the time and date is
incorrect.
Adjust the time and calendar by synchronizing
with the time/date info from your iPhone.
47
Check the time shown on your iPhone.
−
Adjust the time and calendar manually.
64 to 69
74 to 77
Check and correct the reference position.
84
18 to 20
Troubleshooting
Resetting the watch — All Reset
When the watch hands move in an unusual manner (e.g. the hand does not stop
moving, or the watch does not operate even though it has been recharged) due to
strong shock or static, etc., we recommend resetting the watch (All Reset).
Caution
When you reset the watch (All Reset), the settings of the watch will change as
follows:
• Calendar: January 1st (Sunday) (Leap year)
• Local time: ±0 hours
Be sure to adjust the current reference position and time before use.
• The connection is automatically closed if you execute All Reset while the watch
is connected with the iPhone. Use Connect (page 44) to connect with it again
after All Reset. You do not have to register it again.
85
Troubleshooting
Be sure to perform the following operations after All Reset.
1.Correct the reference position.
After performing the All Reset feature, the watch is in the reference position
mode. Refer to the reference position setting procedure outlined on page
76, starting from step 3.
2.Adjust the time and calendar (after correcting the reference
position).
• When adjusting using iPhone:
Connect a iPhone (see page 44),
then obtain the time info (see page 47).
See pages 64 to 69.
• When adjusting manually:
86
Troubleshooting
Make sure the watch is fully charged as outlined on pages 10 to 13 before
proceeding.
1 Pull the crown out to position .
The second hand moves to indicate the 30 seconds
position.
2 Rotate the crown to change the mode to [302].
All hands and identifications other than the second
hand will indicate the current reference position stored
in memory.
Do not operate the watch until all hands/indications
stop moving.
3 Pull the crown out to position .
The second hand indicates the current reference
position.
4Press and release both the lower right button
and upper right button
simultaneously.
When you release the buttons, the watch will vibrate and
all hands will move indicating All Reset is successful.
87
Eco-Drive watch handling precautions
<Always Make Sure to Recharge Frequently>
•Please note that if you wear long sleeves, the watch may stop as a
result of being covered by your sleeve and blocked from the light.
•When you take off the watch, try to place it in as bright a location
as possible. This will ensure optimal operation.
88
Eco-Drive watch handling precautions
CAUTION
Recharging Precautions
•Do not charge the watch at a high temperature (about 60°C
(140°F) or higher) as doing so may cause the movement to
malfunction.
Examples:
•Charging the watch too close to a light source which
generates a large amount of heat such as an incandescent
lamp or halogen lamp.
*When charging under an incandescent lamp, be sure to
leave 50 cm (19-11/16 inch) or more between the lamp
and the watch to avoid exposing the watch to excessive
heat.
•Charging the watch in a location where the temperature
may become extremely high such as on the dashboard of
a vehicle.
89
Eco-Drive watch handling precautions
<Replacement of Rechargeable Cell>
•This watch utilizes a special rechargeable cell that does not require regular replacement.
However power consumption may increase after using the watch for a number of years due
to wear of internal components and deterioration of oils. This may cause stored power to be
depleted at a faster rate. For optimal performance, we recommend having your watch inspected
(chargeable to the owner) by an Authorized Service center to ensure operation is within factory
specifications.
WARNING
Handling of Rechargeable Cell
•The rechargeable cell should never be removed from the watch.
If for any reason it becomes necessary to remove the rechargeable cell from the watch, keep out
of the reach of children to prevent accidental swallowing.
If the rechargeable cell is accidentally swallowed, consult a doctor immediately.
•Do not dispose of the rechargeable cell with ordinary garbage. Please follow the instructions of
your municipality regarding collection of batteries to prevent the risk of fire or environmental
contamination.
90
Eco-Drive watch handling precautions
WARNING
Use Only the Specified Battery
•Never use a battery other than the rechargeable cell specified for use in this watch.
Although the watch structure is designed so that it will not operate when another type of
battery is installed, if a silver battery or other type of battery is installed in the watch and the
watch is recharged, there is the risk of overcharging which may cause the battery to rupture.
This can cause damage to the watch and injury to the wearer.
When replacing the rechargeable cell, always make sure to use the designated rechargeable cell.
91
Water resistance
WARNING
Water Resistance
•Refer to the watch dial and the case back for the indication of the water resistance of your
watch. The following chart provides examples of use for reference to ensure that your watch is
used properly. (The unit “1bar” is roughly equal to 1 atmosphere.)
•WATER RESIST(ANT) ××bar may also be indicated as W.R.××bar.
Indication
Name
Non-water resistant
Everyday-use water resistant
watch
Upgraded everyday use waterresistant watch
92
Dial or Case back
—
WATER RESIST(ANT)
WATER RESIST(ANT)
5 bar
WATER RESIST(ANT)
10/20 bar
Specification
Non-water resistant
Water-resistant to 3
atmospheres
Water-resistant to 5
atmospheres
Water-resistant to 10 or
20 atmospheres
Water resistance
Water-related use
Minor exposure
to water (washing
face, rain, etc.)
Swimming and
general washing
work
Skin diving,
marine sports
Scuba diving
using an air tank
Operate the crown
or button when
the watch is wet
NO
NO
NO
NO
NO
OK
NO
NO
NO
NO
OK
OK
NO
NO
NO
OK
OK
OK
NO
NO
93
Water resistance
•Non-water resistant models are not designed to come into contact with any moisture. Take care
not to expose a watch with this rating to any type of moisture.
•Water resistance for daily use (to 3 atmospheres) means the watch is water resistant for
occasional accidental splashing.
•Upgraded water-resistance for daily use (to 5 atmospheres) means that the watch may be worn
while swimming, but is not to worn while skin diving.
•Upgraded water-resistance for daily use (to 10/20 atmospheres) means that the watch may be
worn while skin diving, but not while scuba or saturated diving using helium gas.
94
Precautionary items and usage limitations
CAUTION
To Avoid Injury
CAUTION
Precautions
•Be particularly careful when wearing your watch while holding a small child, to avoid injury.
•Be particularly careful when engaged in strenuous exercise or work, to avoid injury to yourself
and others.
•Do NOT wear your watch while in a sauna or other location where your watch may become
excessively hot, since there is the risk of burns.
•Be careful when putting on and taking off your watch, since there is a risk of damaging your
fingernails, depending on the manner in which the band is fastened.
•Take off your watch before going to bed.
•Always use the watch with the crown pushed in (normal position). If the crown is of the screw
lock-type, make sure it is securely locked.
•Do NOT operate the crown or any push buttons when the watch is wet. Water may enter the
watch causing damage to vital components.
•If water enters the watch or the watch fogs up and does not clear up even after a long time,
consult your dealer or Customer Support Center for inspection and/or repair.
95
Precautionary items and usage limitations
CAUTION
Precautions (continued)
CAUTION
When Wearing Your Watch
•Even if your watch has a high level of water resistance, please be careful of the following.
•If your watch is immersed in sea water, rinse thoroughly with fresh water and wipe with a
dry cloth.
•Do not pour water from a tap directly onto your watch.
•Take off your watch before taking a bath.
•If seawater enters the watch, place the watch in a box or plastic bag and immediately take it in
for repair. Otherwise, pressure inside the watch will increase, and parts (crystal, crown, push
button, etc.) may come off.
<Band>
•Leather, genuine skin and rubber (urethane) bands will deteriorate over time due to
perspiration, body oils and dirt. Be sure to replace the band periodically.
•The durability of a leather band may be affected when wet (fading, peeling of adhesive), owing
to the properties of the material. Moreover, wet leather may cause a rash.
•It is recommended to take off the watch if it gets wet, even if the watch itself is water-resistant.
•Do not wear the band too tightly. Try to leave enough space between the band and your skin to
allow adequate ventilation.
96
Precautionary items and usage limitations
•The rubber (urethane) band may be stained by dyes or soil present in or on clothing or other
accessories. Since these stains may not be removable, caution is required when wearing your
watch with items that tend to easily transfer color (articles of clothing, purses, etc.). In addition,
the band may be deteriorated by solvents or moisture in the air. Replace with a new one when it
has lost elasticity or become cracked.
•Please request adjustment or repair of the band in the following cases:
•You notice an abnormality with the band due to corrosion.
•The pin of the band is protruding.
•We do not recommend attempting to adjust the watch band yourself. Special expertise and
experience is required for proper adjustment. If not adjusted correctly, the band may become
detached leading to loss of your watch. (Some retailers may supply a band adjustment tool with
your purchase).
For band adjustment, we recommend you consult the retailer from where the watch was
purchased or your nearest Authorized Citizen Service Center. Some repair shops may charge a
nominal fee for adjustment if the watch was not purchased directly from them.
<Temperature>
•The watch may stop or the function of the watch may be impaired in extremely high or low
temperature. Do not use the watch in places where the temperature is outside the operating
temperature range as stated in the specifications on pages 102 and 103.
97
Precautionary items and usage limitations
<Magnetism>
•Analog quartz watches are powered by a step motor that uses a magnet. Subjecting the watch to
strong magnetism from the outside can cause the motor to operate improperly and prevent the
watch from keeping time accurately.
Do not allow the watch to come into close proximity to magnetic health devices (magnetic
necklaces, magnetic elastic bands, etc.) or the magnets used in the latches of refrigerator doors,
clasps used in handbags, the speaker of a cell phone, electromagnetic cooking devices and so on.
<Strong Shock>
•Avoid dropping the watch or subjecting it to other strong impact. It may cause malfunctions
and/or performance deterioration as well as damage to the case and bracelet.
<Static Electricity>
•The integrated circuits (IC) used in quartz watches are sensitive to static electricity. Please note
the watch may operate erratically or not at all if exposed to intense static electricity.
<Chemicals, Corrosive Gasses and Mercury>
•If paint thinner, benzene or other solvents or products containing these solvents (including
gasoline, nail-polish remover, cresol, bathroom cleaners and adhesives, water repellent, etc.)
are allowed to come into contact with the watch, they may discolor, dissolve or crack the
materials. Be careful when handling these chemicals. Contact with mercury such as that used
in thermometers may also cause discoloration of the band and case.
98
Precautionary items and usage limitations
<Protective Stickers>
•Be sure to remove any protective stickers that may be on your watch (case back, band, clasp,
etc.). Otherwise, perspiration or moisture may enter the gaps between the protective stickers
and the parts, which may result in a skin rash and/or corrosion of the metal parts.
CAUTION
Always Keep Your Watch Clean
•Rotate the crown while it is pressed in fully and press the buttons periodically so they do not
become stuck due to accumulations of foreign matter.
•The case and band of the watch come into direct contact with the skin in the same manner as
undergarments. Corrosion of the metal or unnoticed soiling such as that caused by perspiration
and dirt can soil sleeves and other portions of clothing. Keep your watch clean at all times.
•The case and band of the watch come into direct contact with the skin. If you think there is
something wrong, discontinue wearing the watch immediately and consult your physician.
In the case of accumulation of sweat or dirt on a metal band or case, clean thoroughly using
a brush and neutral detergent. In the case of a leather or rubber (urethane) band, wipe clean
using a dry cloth.
•Leather bands may become discolored by perspiration or dirt. Always keep your leather band
clean by wiping with a dry cloth.
99
Precautionary items and usage limitations
Caring for Your Watch
•Wipe any dirt or moisture such as perspiration from the case and crystal with a soft cloth.
•For a metallic, plastic or rubber (urethane) watchband, wash any dirt off with water.
Remove the small amounts of dirt trapped between the crevices of the metallic band with a
soft brush.
•For a leather band, wipe off dirt using a dry cloth.
•If you will not be using your watch for an extended period of time, carefully wipe off any
perspiration, dirt or moisture and store in a proper location, avoiding locations subject to
excessively high or low temperatures and high humidity.
<When Luminous Paint is used for your watch>
The paint on the dial and hands helps you with reading the time in a dark place. The luminous
paint stores light (daylight or artificial light) and glows in a dark place.
It is free from any radioactive substance or any other material harmful to a human body or
environment.
•The light emission gradually becomes weaker as time passes.
•The duration of the light (“glow”) will vary depending on the brightness, types of and
distance from a light source, exposure time, and the amount of the paint.
•The paint may not glow and/or may dissipate quickly if exposure to light was not sufficient.
100
Information
About Bluetooth
Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
Some countries may prohibit the usage of the Bluetooth. See page 61.
101
Specifications
Model
W760
Timekeeping accuracy
(without reception)
Within ±15 seconds per month when worn at normal operation
temperatures between +5˚C (41°F) and +35˚C (95°F)
Operating temperature
range
–10˚C (14°F) to +60˚C (140°F)
Display functions
• Time: Hours, minutes, seconds, 24-hour
• Calendar: Date, day of the week
Type
Analog solar-powered watch
Maximum run time from full • Fully charged to fully discharged (when power save feature
works about 7.5 hours a day):
charge
•
Battery
102
Approximately 8 months (with using iPhone)
Approximately 17 months (without using iPhone)
Power reserve upon insufficient charge warning function:
Approximately 10 days
Rechargeable cell (lithium button cell), 1 pc.
Specifications
Additional
functions
•
•
•
•
•
•
Solar power function
Power reserve indication (in four levels)
Overcharging prevention function
Insufficient charge warning function (two-second interval movement)
Energy saving function (power save feature)
Indications relative to iPhone
Connection status indication (ON/OFF)
Indication of ongoing communication processing (ACT)
Notification indication (CALL/INFO/LL)
• Chronograph (up to 60 minutes in one second increments)
• Local time
• Perpetual calendar (until February 28th, 2100)
Specifications and contents of this booklet are subject to change without prior
notice.
103
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement