PRID_11021_doc_152.933_Neso_1_5W_RGB_Analog_PROLaser_DMX (Öppnas i nytt fönster)

PRID_11021_doc_152.933_Neso_1_5W_RGB_Analog_PROLaser_DMX (Öppnas i nytt fönster)
Ref. Nr. 152.933
Neso 1,5W RGB Analog PRO Laser DMX
MANUAL
ENGLISH
Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in
order to benefit fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions
to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical
shock. Keep the manual for future reference.
- Prior to using the unit, please ask advice from a
specialist. When the unit is switched on for the first time,
some smell may occur. This is normal and will disappear
after a while.
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the unit
This may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical shock
and malfunction.
- When unplugging the unit from a mains outlet, always
pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they
need to be replaced by a qualified technician.
- If the unit is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains outlet
and DO NOT switch the unit on. Contact your dealer. Do
NOT connect the unit to a rheostat or dimmer.
- To avoid fire and shock hazard, do not expose the unit to
rain and moisture.
- All repairs should be carried out by a qualified technician
only.
- Connect the unit to an earthed mains outlet
(220-240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used for a
longer period of time, unplug it from the mains. The rule
is: Unplug it from the mains when not in use.
- If the unit has not been used for a longer period of time,
condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the unit
in humid rooms or outdoors.
- During operation, the housing becomes very hot. Do not
touch it during operation and immediately after.
- To prevent accidents in companies, you must follow the
applicable guide lines and follow the instructions.
- Secure the unit with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
effect at least 50cm away from inflammable material and
leave at least 1 meter space on every side to ensure
sufficient cooling.
- This unit contains high intensity LEDs. Do not look into
the LED light to prevent damage to your eyes.
- Do not repeatedly switch the fixture on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not leave
the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice from
a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
- If the unit has fallen, always have it checked by a
qualified technician before you switch the unit on again.
- Do not use chemicals to clean the unit. They damage the
varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the unit off prior to unplugging it from the mains
and/or other equipment. Unplug all leads and cables
prior to moving the unit.
- Make sure that the mains lead cannot be damaged when
people walk on it. Check the mains lead before every
use for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if power
outlet match. If you travel, make sure that the mains
voltage of the country is suitable for this unit.
- Keep the original packing material so that you can
transport the unit in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of
sufficient magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he
should read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic
attacks should be aware of the effects that this light effect may have on them.
The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate
and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F
and 35°C/95°F.
-
-
-
-
-
-
-
-
-
Features of the product:
1. Scanner system: 25K high speed optical scanner 2. Working Modes: Sound Active, Auto run, DMX512 (12 CH), Master/slave mode, ILDA mode. 3. Interface: 3 pins XLR jack for DMX or Maser‐Slave linking; DB25 ILDA interface for PC control 4. Input power: AC 110V~240V, 50/60Hz. Rated power: 50W. 5. Packing Size: L*W*H=30.2*30.2*26CM; Weight: 5.5KG Front and Rear panel view:
1
2
3
4
5
6
7
8
9
10
14
15
11
16
12
13
1. Laser Aperture
9. LCD function setting panel
2. Running LED
10. Interlock
3. Power LED indicator
11. DMX interface
4. Mic LED
12. ON/OFF switch
5. DMX signal LED
13. Power Jack
6. Key switch
14. Y invert
7. Sound sensitivity knob
15. X invert
8. Sound active microphone
16. DB25 ILDA interface
ENTER
UP
DOWN
Press “UP” or “DOWN” to choose functions in the same menu.
Press “ENTER” button to enter next menu. Press “RETURN” button to return previous menu.
When you turn on the laser for the first time, it will take some seconds to auto load the built-in show.
The default setting is AUTO EFFECT 1.
Second Menu
Third Menu
Running
DMX512
A001 (DMX address)
Running
AUTO
Effect 1 (Full show)
(auto running mode)
Effect 2 (only beam)
Effect 3 (only cartoon)
Running
Music
(sound
mode)
activate
Effect 1 (Full show)
Effect 2 (only beam)
Effect 3 (only animation)
Address
Choose DMX address
OFF
Setting
Light
ON
(LCD backlight setting)
ON 5S (ON for 5 seconds)
ON 10S (ON for 10 seconds)
Press UP and down to choose
Cartoon (Running speed)
running speed from 1~99,
99 is the fastest
Fourth Menu
Master (set master unit)
OFF
ON
(press up or down to
Size
choose
the
size
of
graphics)
LASER
1. Single Color (1~7)
(size and color setting)
2. RGY
Color
Yes
(Restore default setting)
No
Universal DMX Operation (DMX mode)
This mode allows you to use universal DMX-512 console to operate.
1. Install the units in a suitable position.
2. Use standard XLR cable to connect your units together via the XLR connector on the rear of the units. For longer
cable we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches.
4. Turn on all units. Use DMX console to control your units.
DMX Signal
Instruction for DMX channels
LASER
0~41
42~83
DMX mode, CH2~CH12 valid
84~125
Build-in cartoon graphics auto running mode
126~167
Build-in beam graphics auto running mode
168~209
Build-in beam graphics auto running mode
210~251
Build-in cartoon graphics auto running mode
252~255
DMX mode, CH2~CH12 valid
0~255
Selecting built-in patterns
0~127
Manual rotation
128~191
Auto counter-clockwise rotation (from slow to fast)
192~255
Auto clockwise rotation (from slow to fast)
X axis
0~127
Manual rolling
rolling
128~255
Auto rolling (from slow to fast)
Y axis
0~127
Manual rolling
rolling
128~255
Auto rolling (from slow to fast)
X axis
0~127
Manual choose moving position
moving
128~255
Auto moving (from slow to fast)
Y axis
0~127
Manual choose moving position
moving
128~255
Auto moving (from slow to fast)
0~63
Choose pattern size, 0 is normal size, 1 is the smallest, 63 is the biggest
64~127
Auto zooming (-) from slow to fast
128~191
Auto zooming (+) from slow to fast
192~255
Manual zooming (+/-) from slow to fast
0~255
Auto drawing from slow to fast
0~127
Choose sanning speed from slow to fast
128~255
Choose the length of dot
0~24
Normal color
Color
25~199
Choose every single color
setting
200~224
Every single color changing one by one
225~255
All the colors together changing alternatively in one pattern
0~255
Adjust color changing speed from slow to fast
OFF
Auto
CH1
Activate
Sound
Activate
CH2
CH3
CH4
CH5
CH6
CH7
Pattern
select
Rotation
Pattern
size
CH8
Zooming
CH9
Drawing
Scanning
CH10
speed
Display
dot
CH11
Color
CH12
TROUBLE SHOOTING
1. If the power indicator is off and the laser doesn't work, please check the power supply and the input. 2. In Stand‐Alone operation, if the power supply indicator is ON and sound active indicator is OFF, but the laser doesn't work. A. The sound may be too small and cannot activate the laser running, please increase the music volume or increase sound sensitivity on rear panel. B. Please check if unit has been set up in slave mode, or DMX mode. 3. In Master‐Slave operation, slave units don't running, please check as below. A. Make sure there's only one master in the chain, and the others are set in slave mode. B. Make sure to use a good quality power cable and XLR connector. 4. In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal indicator is flashing, please make sure the DMX console and unit have the same channel. After trying the above solution you still cannot sort out the problem, please contact your dealer or our company for service CE Declaration of Conformity
Importer:
Product number:
152.933
Product Description:
Neso 1,5W RGB Analog PROLaser DMXSD
Regulatory Requirement:
The product meets the requirements stated in the above mentioned Standards.
22-07-2013
Signature :
www.tronios.com
Copyright © 2013 by TRONIOS the Netherlands
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed