Citoborma 111 Operators Manual

Citoborma 111 Operators Manual
CITOBORMA 111
14
13
12
1
11
2
3
5
4
5
6
7
8
9
15
2
16
17
10
18
3
Materiale
• Nagel-papirbor
• Boreunderlag
• Vokspapir
4
5
6
7
Michael Kipp
Direktør
8
9
10
11
12
13
14
15
Dear Customer,
Thank you for deciding on our paper drilling machine. You have made a
good choice in purchasing this quality product.
Please do read these operating instructions before using the machine and
follow the safety instructions.
Throughout the text, the numbers in brackets refer to the diagrams.
Description of function
• Nagel paper drills
• Drilling base
• Waxed paper
1. On/Off switch
2. Safety cover
3. Knurled screw to clamp hand guard
4. Sliding platform
5. Lateral stops
6. Knurled screw to clamp lateral stop
7. Release button for sliding platform
8. Program stip to set hole spacing
9. Drilling base
10. Waste container
11. Drilling spindle
12. Knurled nut
13. Setting screw
14. Hand lever
15. Knurled screw
16. Waxed paper
17. Paper drill
18. Allan key
Extras
• Stop for 2 - 4.5 mm
paper drills
• Drill sharpener
•
• Program strip for
special requirements
16
Setting up
Set up machine on a firm, level surface facing the operator and plug in the
mains plug.
Fit sliding platform
Push sliding platform from the front onto the foot of the drilling machine
stand. To do so, push the screw on the underside of the sliding platform
into the slit of the foot of the stand.
Push the sliding table backwards until the longitudinal holes are over the
tap holes of the foot of the stand and tighten the knurled screws (15) from
above.
Insert drilling base (9) in the recess of the sliding platform.
Mount hand lever
Screw in hand lever (14).
Inserting paper drill
Insert paper drill into the drilling spindle (11) up to the stop and tighten up
with the Allan key (18).
17
Setting hole spacing
Using the CITOBORMA 111, you can quickly and accurately perforate
standardised hole spacings.
To unlock, press release button (7) and move sliding platform (4) to the far
left. Keep release button (7) depressed in this position and set the desired
drilling program.
Program strips with special hole patterns can be obtained as an extra item.
Setting drilling depth
Press hand lever down until the drill is resting on the drilling base with
gentle pressure.
Turn setting screw (13) upwards until it abuts the hand lever.
Screw knurled screw (12) down to fix the position of the setting screw.
18
Operation
Switch machine on at the On/Off switch (1).
Insert the paper to be perforated between the two lateral stops (5) and fix
in position using knurled screw (6).
Push paper drill through the pile with an even movement and move up
again. Do not leave drill in the paper an unnecessarily long time, or it may
overheat.
Faults
Fault
Machine not running:
Ragged holes:
Hand lever hard to move,
drills break:
Drills block,
drills squeak:
Bottom sheets not perforated:
Remedy
Plug in mains plug,
switch on main switch
Replace blunt drill,
replace drilling base
Replace blunt drill,
replace drilling base
Perforate waxed paper
Adjust drilling depth downwards
If faults are not eliminated by these instructions, please contact your Nagel
dealer.
Technical data
Noise emission:
Power supply:
Drill diameter:
1 Max. pile depth:
2
< 70 dB (A)
see rating plate
2 - 9 mm
50 mm
19
Safety instructions
Only perform repairs using original Nagel spare parts.
Use machine only for drilling paper and cardboard.
Do not reach into the drilling area.
Disconnect plug before opening the machine and in the event of the machine
being idle for a prolonged period.
Only set up machine in a dry room.
Declaration of conformity
This machine conforms to the following EC directives:
Low-voltage Directive 73/23 EN, EMC Directive 89/336, Machinery Directive 89/392,
with standards
EN60204, EN1010, 55014/EL, EP; 61000-3-2
3 being applied.
Michael Kipp
Managing Director
20
21
Material de consumo
22
23
24
26
27
28
29
30
31
Michael Kipp
Gérant
32
33
34
35
36
37
38
39
Verbruiksmateriaal
Functiebeschrijving
• Nagel papierboor
• Boorondergrond
• Waspapier
40
41
DIN A5-ringband
DIN A4-ringband
Filofax planner
US-ringband
42
33 Technische specificaties
Geluidsemissie:
Voedingsspanning:
Boordiameter:
Stapelhoogte max.:
43
Michael Kipp
Directeur
44
45
• Nagel-papirborer
• Boreunderlag
• Vokset papir
46
47
48
49
50
51
52
53
54
55
Michael Kipp
Verkställande direktör
56
57
58
CITOBORMA 111
01.07.1998
59
Inland
0711 78078 11
Export +49711 78078 21
Telefax +49711 78078 10
www.ernstnagel.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed