OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Catalog No.

OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Catalog No.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
Catalog No.
No de Cat.
0233-20
0234-6
0235-21
0244-1
HEAVY-DUTY MAGNUM DRILLS
EXTRA ROBUSTE PERCEUSES MAGNUM
TALADROS MAGNUM HEAVY-DUTY
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure
to follow the warnings and instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference. The term "power
tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
•Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
•Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
•If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WORK AREA SAFETY
•Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
•Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
•Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
•Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
•Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
•Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
PERSONAL SAFETY
•Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
•Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
2
SERVICE
•Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
3
SPECIFIC SAFETY RULES
Double Insulated
Amps
Volts
Alternating Current Only
No Load Revolutions
per Minute (RPM)
C
120
5.5
0-2800
0234-6
120
5.5
without RAD 0-950
RAD low 0-630
Rad high 0-1425
0235-21
120
5.5
0-950
0244-1
120
5.5
without RAD 0-700
RAD low 0-465
RAD high 0-1050
Underwriters Laboratories, Inc.
United States and Canada
EXTENSION CORDS
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cord to make up the total length, be sure each cord
contains at least the minimum wire size required.
If you are using one extension cord for more than
one tool, add the nameplate amperes and use the
sum to determine the required minimum wire size.
Guidelines for Using Extension Cords
•If you are using an extension cord outdoors, be
sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.
•Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualified person before using it.
•Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Right Angle Drive Unit Cat. No. 48-06-2871
FUNCTIONAL DESCRIPTION
2
US
Mexican Approvals Marking
No Load RPM
0233-20
3
1
Recommended Minimum Wire Gauge
For Extension Cords*
Extension Cord Length
1. Chuck
2. Side handle
3. Nameplate
4. Trigger
5
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically “live” terminal.
Your tool must be plugged into
an appropriate outlet, properly
installed and grounded in accordance with all codes and ordinances. The plug and outlet should look Fig. A
like those in Figure A.
WARNING Improperly connecting the
SPECIFICATIONS
Cat. No. Volts AC Amps
READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE.
GROUNDING
SYMBOLOGY
•Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
•Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
•Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•WARNING Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
4
5. Forward/Reverse switch
Nameplate Amperes
25'
50'
75' 100' 150'
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
18
18
18
18
16
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
18
16
14
12
10
16
14
12
12
grounding wire can result in the risk of electric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the tool. Never remove the
grounding prong from the plug. Do not use
the tool if the cord or plug is damaged. If
damaged, have it repaired by a MILWAUKEE
service facility before use. If the plug will not
fit the outlet, have a proper outlet installed by
a qualified electrician.
Double Insulated Tools:
Tools with Two Prong Plugs
Tools marked “Double Insulated” do not require
grounding. They have a special double insulation system which satisfies OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories, Inc.,
the Canadian Standard Association and the National Electrical Code. Double Insulated
tools may be used in either of
the 120 volt outlets shown in Fig. B Fig. C
Figures B and C.
Grounded Tools: Tools with Three Prong Plugs
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See Figure A). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
ASSEMBLY
WARNING To prevent personal injury,
always remove the chuck key from the chuck
after each use.
WARNING To reduce the risk of injury,
always unplug tool before changing or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Installing Bits into Keyed Chucks
(Cat. No. 0234-6, 0244-1)
Always unplug the tool before installing or removing bits.
1. Open the chuck jaws wide enough to insert the bit.
Be sure the bit shank and chuck jaws are clean.
Dirt particles may prevent the bit from lining up
properly.
2. When using drill bits, insert the bit into the chuck.
Center the bit in the chuck jaws and lift it about
1/16" off of the bottom. Tighten the chuck jaws by
hand to align the bit.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the bit shank.
Tighten the chuck jaws by hand to align the bit.
3. Place the chuck key in each of the three holes in
the chuck, turning it clockwise as shown. Tighten
securely.
Removing and Replacing Quik-Lok® Cords
MILWAUKEE's exclusive Quik-Lok® Cords provide
instant field replacement or substitution.
Fig. 1
1
2
3
4
1. To remove the Quik-Lok® Cord, turn the cord nut
1/4 turn to the left and pull it out.
2. To replace the Quik-Lok® Cord, align the connector keyways and push the connector in as far as it
will go. Turn the cord nut 1/4 turn to the right to lock.
Fig. 2
Installing Side Handle
MILWAUKEE Magnum Drills are supplied with a
side handle that can be installed on either side of
the tool for right or left handed use. To install the
side handle, thread it into the socket on the desired
side of the tool and tighten it securely. Always use
the side handle for best control.
Tighten
Loosen
4. To remove the bit, insert the chuck key into one of
the holes in the chuck and turn it counterclockwise.
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
4
5
NOTE: If the spindle rotates when opening or closing
the chuck jaws, grasp the chuck and slightly rotate
back and forth to engage the spindle-lock mechanism.
The spindle will remain locked until the tool is turned
on. The spindle-lock mechanism will automatically
disengage when the tool is turned on.
WARNING To reduce the risk of injury:
Do not grasp the bit while the chuck is rotat
ing or while the bit is falling from the chuck.
Release the trigger as soon as the ratcheting
stops to avoid throwing the bit.
Installing Bits into Keyless Chucks
(Cat. No. 0233-20)
These tools are equipped with a hand-tightening
keyless chuck. Always unplug the tool before installing or removing bits.
Fig. 3
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Sleeve
Fig. 6
Locking Trigger
The lock button holds the trigger in the ON position
for continuous full speed use.
Removing the Chuck From RAD
The chuck can be removed from the Right Angle
Drive Unit in the same manner it is removed from
the drill; however, ALWAYS REMOVE RIGHT
ANGLE DRIVE FROM THE DRILL BEFORE ATTEMPTING TO LOOSEN Fig. 8
THE CHUCK. This will prevent damaging the drill's
gearing. Use the open
end wrench provided to
hold the Right Angle Drive
spindle before attempting
to loosen the chuck.
Fig. 10
FWD.
K
Installing Bits into Keyless Chucks
(Cat. No. 0235-21)
These tools are equipped with a spindle-lock mechanism and a single-sleeve keyless chuck. Always
unplug the tool before inserting or removing bits.
1. To open the chuck jaws, turn the chuck sleeve
in counterclockwise direction.
2. To install a bit, open the chuck jaws slightly wider
than the bit. Center the bit in the chuck jaws and
lift it about 1/16" off of the bottom. Align the bit
as shown (Fig. 4).
Starting, Stopping and Controlling Speed
1. To start the tool, pull the trigger.
2. To stop the tool, release the trigger.
3. To vary the drilling speed, simply increase or
decrease pressure on the trigger. The further
the trigger is pulled, the greater the speed.
C
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, hold the collar while
turning the sleeve in the clockwise direction.
Tighten securely.
WARNING To reduce the risk of injury,
keep hands and cord away from the bit and
all moving parts.
LO
Chuck Removal
This tool is equipped with a threaded spindle to hold
the chuck. Before removing the chuck, unplug the
tool and open the chuck jaws. A left-handed thread
screw is located inside the chuck to prevent the
chuck from loosening when the tool is operated
in reverse direction. Remove the screw by turning
it clockwise. To remove the chuck, hold the tool
so that only the side of the chuck rests firmly and
squarely on a solid workbench. Insert the chuck
key or a chuck remover bar in one of the keyholes.
Turn the chuck so the key is at about a 30° angle
to the bench top and strike the key sharply with a
hammer so the chuck turns in a counterclockwise
direction (looking from the front of the tool). This
should loosen the chuck from the spindle which
has a right hand thread making it easy to remove
the chuck by hand.
NOTE: When replacing the chuck, always replace
the left hand thread screw in the chuck.
Collar
1. For forward (clockwise) rotation, push the forward/reverse switch to FWD as shown.
2. For reverse (counterclockwise) rotation, push
the forward/reverse switch to REV as shown.
Although an interlock prevents reversing the tool
while the motor is running, allow it to come to a
full stop before reversing.
1. Remove the chuck from the drill following instructions (See “Removing the Chuck From the Drill”).
Slip the double hex coupling (1) over the hex on
the drill spindle.
Loosen the clamping screws on the clamping
sleeve (2) and slip the sleeve onto the drill collar.
2. Slide the Right Angle Drive head (4) into the other
side of the sleeve and turn the drive head slightly
in either direction so the hexagonal hole in the
coupling (1) engages the hexagonal portion of
the spindle (3).
NOTE: Attaching the drill chuck to the side
marked “LOW” reduces the speed by 1/3, or
33%. Attaching the drill chuck to the opposite
side increases the speed by 50%.
3. When assembled, turn the Right Angle Drive
head to the desired position and tighten the
clamping screws to secure the unit. Thread the
chuck onto the Right Angle Drive spindle (5).
INSTALL CHUCK LOCKING SCREW.
Lock button
1. To lock the trigger, hold the lock button in while
pulling the trigger. Release the trigger.
2. To unlock the trigger, pull the trigger and release.
The lock button will pop out.
OPERATION
WARNING To reduce the risk of explosion, electric shock and property damage,
always check the work area for hidden pipes
and wires before drilling.
WARNING To reduce the risk of injury,
always unplug tool before attaching or removing accessories or making adjustments. Use
only specifically recommended accessories.
Others may be hazardous.
Fig. 4
Drilling
1. Before drilling, be sure the workpiece is clamped
securely. Use backing material to prevent damage to the workpiece during breakthrough.
2. When starting a hole, place the drill bit on the
work surface and apply firm pressure. Begin
drilling at a slow speed, gradually increasing the
speed as you drill.
3. Always apply pressure in line with the bit. Use
enough pressure to keep the drill biting, but do
not push hard enough to stall the motor.
4. Reduce pressure and ease the bit through the
last part of the hole. While the tool is still running,
pull the bit out of the hole to prevent jamming.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side shields.
Using Forward/Reverse Switch
Attaching Right Angle Drive (RAD) to Drill
Fig. 7
3. To close the chuck jaws, turn the chuck sleeve
in clockwise direction (Fig. 5). Tighten securely.
Several detents will be felt as the chuck sleeve
is turned.
Fig. 5
Fig. 9
Forward
3
1
4
Stalling
If the tool seems as if it is about to stall, maintain a
firm grip and reduce pressure slightly to allow the
bit to regain speed. If the tool does stall, release
the trigger immediately. Reverse the motor, remove
the bit from the work and start again. Do not pull
the trigger on and off in an attempt to start a stalled
drill. This can damage the drill.
2
5
Sleeve
Reverse
6
Trigger
7
MAINTENANCE
APPLICATIONS
CAPACITIES
Wood
Cat. No.
0233-20
0234-6
RAD low
RAD high
0235-21
0244-1
RAD low
RAD high
Flat Boring
Bits
1”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
Auger
Bits
N/R
1-1/2”
1-1/2”
1-1/8”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
Ship Auger Bits
N/R
1-1/4”
1-1/2”
1”
1-1/4”
1-1/2”
1-1/2”
1-1/4”
Selecting Bits
When selecting a bit, use the right type for your
job. For best performance, always use sharp bits.
Selfeed
Bits
N/R
2”
2-1/4”
1-1/2”
2”
2-1/4”
2-9/16”
1-3/4”
Hole
Saws
1-3/4”
4”
4-1/2”
2-3/4”
4”
4-1/2”
5”
3-1/4”
Steel
Twist
Hole
Drill
Saws
3/8”
1”
1/2”
2”
1/2”
2-1/8”
1/2”
1-1/2”
1/2”
2”
1/2”
2-1/4”
1/2”
2-1/4”
1/2”
1-3/4”
Masonry
CarbideTipped Bits
3/8”
1/2”
9/16”
7/16”
1/2”
9/16”
5/8”
1/2”
To reduce the chance of bit binding:
•Use sharp bits. Sharp bits are less likely to bind
when drilling.
•Use the proper bit for the job. There are bits that
are designed for specific purposes.
•Use caution when drilling pitchy, knotty, wet or
warped material or when drilling in material that
may contain nails.
Typical Bracing Methods
Forward rotation
Fig. 11
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, start the drill slowly, gradually increasing
speed as you drill. When using twist drill bits, pull
the bit out of the hole frequently to clear chips from
the bit flutes. Use low speeds for plastics with a
low melting point.
Drilling in Masonry
When drilling in masonry, use high speed carbidetipped bits. Drilling soft masonry materials such as
cinder block requires little pressure. Hard materials
like concrete require more pressure. A smooth,
even flow of dust indicates the proper drilling rate.
Do not let the bit spin in the hole without cutting.
Do not use water to settle dust or to cool bit. Both
actions will damage the carbide.
Reaction
Bracing against the floor
Drilling in Metal
When drilling in metal, use high speed steel twist
drills or hole saws. Use slow speeds for hard metals
and high speeds for softer metals. Lubricate drill
bits with cutting oil when drilling in iron or steel. Use
a coolant when drilling in nonferrous metals such
as copper, brass or aluminum. Back the material
to prevent binding and distortion on breakthrough.
Fig. 12
Driving Screws
When driving screws, use the proper screwdriver
bit for your job. After drilling pilot and shank holes,
start the screw slowly and increase the speed as
driving progresses. Set the screw by slowing to a
stop. Do not run screws down at excessive speeds.
To remove screws, reverse the motor.
WARNING
Bracin against
Bracing
gainst
a stud
d
Reaction
R
i
Reverse rotation
8
Replacing Brushes
MILWAUKEE Magnum Drills have an exclusive
Brush Cartridge System. The tool will not start when
the brushes are worn to 1/8", preventing expensive
damage to the armature. New brushes are provided
in the Cartridge for fast changes anywhere.
Fig. 14
Brush
holder
screw
Brush holder
Extra
brushes
Brushes
WARNING To reduce the risk of injury,
electric shock and damage to the tool, never
immerse your tool in liquid or allow a liquid
to flow inside the tool.
1. Unplug tool and rest it on its side with the cartridge facing up. Loosen the brush holder screw
in the cartridge and pull cartridge out.
Cleaning
Clean dust and debris from vents. Keep the tool
handles clean, dry and free of oil or grease. Use
only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents
are harmful to plastics and other insulated parts.
Some of these include: gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use flammable or combustible
solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the
nearest service center.
Reaction
High rotational force. To
reduce the risk of injury, always hold or brace
securely. Always use side handle on tools
rated 1200 RPM or less.
Bit Binding
A high rotational force occurs when a bit binds. If
the bit binds, the tool will be forced in the opposite
direction of the bit rotation (See Fig. 11 - 13). Bits
may bind if they are misaligned or when they are
breaking through a hole. Wood boring bits can also
bind if they run into nails or knots. Be prepared for
bit binding situations.
Maintaining Tools
Keep your tool in good repair by adopting a regular
maintenance program. Before use, examine the
general condition of your tool. Inspect guards,
switches, tool cord set and extension cord for
damage. Check for loose screws, misalignment,
binding of moving parts, improper mounting, broken parts and any other condition that may affect
its safe operation. If abnormal noise or vibration
occurs, turn the tool off immediately and have the
problem corrected before further use. Do not use a
damaged tool. Tag damaged tools “DO NOT USE”
until repaired (see “Repairs”).
Under normal conditions, relubrication is not necessary until the motor brushes need to be replaced.
After six months to one year, depending on use,
return your tool to the nearest MILWAUKEE service
facility for the following:
•Lubrication
•Brush inspection and replacement
•Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.)
•Electrical inspection (switch, cord, armature, etc.)
•Testing to assure proper mechanical and electrical
operation
always unplug your tool before performing
any maintenance. Never disassemble the tool
or try to do any rewiring on the tool’s electrical
system. Contact a MILWAUKEE service facility
for ALL repairs.
Fig. 15
Bracing
against
your leg
Forward
rotation
Fig. 13
WARNING Never use a different screw
as a brush holder screw.
WARNING To reduce the risk of injury,
Reaction
on
Forward rotation
2. Remove worn brushes. If the brushes should fall
into the tool, be sure to shake them out before
reinserting the cartridge. Discard BOTH brushes.
Brushes should always be replaced in sets.
3. A set of spare brushes is provided in the cartridge. Remove the brushes from storage compartment.
4. Position new brushes with the flat silver end facing into the brush holder. Push cartridge into the
tool and press evenly on top and bottom of the
cartridge to align terminals for proper connection.
5. Tighten the brush holder screw gently. If the head
of screw is damaged, use only MILWAUKEE
replacement parts.
ACCESSORIES
WARNING To reduce the risk of injury,
always unplug the tool before attaching or
removing accessories. Use only specifically
recommended accessories. Others may be
hazardous.
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go on-line
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or a service center.
9
LIMITED WARRANTY - USA AND CANADA
Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct
CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain
exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship for a period of five (5) years* after the
date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the
proof of purchase should be included with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Industrial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED
Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb
fails the Work Light or Upgrade Bulb will be replaced free of charge.
*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline
Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,
Reconditioned product and Test & Measurement products. There are separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.
The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is
provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A
CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT
AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE
OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY
CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN
OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH
IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS
DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty
and non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the
original proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to find the nearest ASC, for service, parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all
freight costs relative with this warranty process.
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.
Model:
Date of Purchase:
Distributor or Store Stamp:
10
DESCRIPTION FONCTIONNELLE
2
3
1
5
4
PICTOGRAPHIE
RÈGLES DE SÉCURITÉ
SPÉCIFIQUES
Courant alternatif
Tours-minute. á vide (RPM)
C
US
SPÉCIFICATIONS
No de
cat.
0233-20
0234-6
12
MISE A LA TERRE
12,2
22,8
30,4
16
16
14
12
10
16
16
14
12
10
16
14
12
10
10
14
12
10
10
--
45,7 60,9
12
10
----
12
-----
LISEZ ATTENTIVEMENT CES
INSTRUCTIONS ET CONSERVEZ-LES
POUR LES CONSULTER AU BESOIN.
13
MONTAGE DE L’OUTIL
Fig. 2
Serrez
Desserrez
Fig. 1
1
2
3
4
Fig. 3
Collet
3
14
1
AVERTISSEMENT
4
2
5
15
APPLICATIONS
CAPACITIES
MANIEMENT
Fig. 10
C
K
Fig. 9
Avant
Inverse
FWD.
Bois
No.
de cat.
Acier
Lamesscies
Lamesscies
N/R
N/R
N/R
38 mm
(1-1/2”)
38 mm
(1-1/2”)
29 mm
(1-1/8”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
32 mm
(1-1/4”)
38 mm
(1-1/2”)
25 mm
(1”)
32 mm
(1-1/4”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
32 mm
(1-1/4”)
51 mm
(2”)
57 mm
(2-1/4”)
38 mm
(1-1/2”)
51 mm
(2”)
57 mm
(2-1/4”)
65 mm
(2-9/16”)
45 mm
(1-3/4”)
45 mm
(1-3/4”)
102 mm
(4”)
114 mm
(4-1/2”)
70 mm
(2-3/4”)
102 mm
(4”)
114 mm
(4-1/2”)
127 mm
(5”)
83 mm
(3-1/4”)
10 mm
(3/8”)
13 mm
(1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
25 mm
(1”)
51 mm
(2”)
54 mm
(2-1/8”)
38 mm
(1-1/2”)
51 mm
(2”)
57 mm
(2-1/4”)
57 mm
(2-1/4”)
45 mm
(1-3/4”)
LO
16
Rotation avant
Balais
Reaction
Fig. 13
Reaction
Rotation inverse
Reaction
Rotation avant
19
20
SIMBOLOGÍA
Doble aislamiento
REGLAS ESPECIFICAS
DE SEGURIDAD
Amperios
US
DESCRIPCION FUNCIONAL
1
2
3
TIERRA
EXTENSIONES ELECTRICAS
7,6
12,2
22,8
30,4
16
16
14
12
10
16
16
14
12
10
16
14
12
10
10
14
12
10
10
--
45,7 60,9
12
10
----
12
-----
LEA Y GUARDE TODAS LAS
INSTRUCCIONES PARA FUTURAS
REFERANCIAS.
Fig. C
23
1.
2.
2
4
3
®
Fig. 4
Apretar
Aflojar
Collar
Para cerrar
Fig. 7
4
FWD.
C
K
APPLICACIONES
CAPACIDADES
Madera
Cat. No.
Acero
N/R
N/R
N/R
38 mm
(1-1/2”)
32 mm
(1-1/4”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
0235-21
0234-6
Concreto
0233-20
Fig. 10
LO
51 mm
(2”)
45 mm
(1-3/4”)
102 mm
(4”)
10 mm
(3/8”)
13 mm
(1/2”)
25 mm
(1”)
51 mm
(2”)
10 mm
(3/8”)
13 mm
(1/2”)
38 mm
(1-1/2”)
57 mm
(2-1/4”)
114 mm
(4-1/2”)
13 mm
(1/2”)
54 mm
(2-1/8”)
14 mm
(9/16”)
29 mm
(1-1/8”)
25 mm
(1”)
38 mm
(1-1/2”)
70 mm
(2-3/4”)
13 mm
(1/2”)
38 mm
(1-1/2”)
11 mm
(7/16”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
32 mm
(1-1/4”)
38 mm
(1-1/2”)
51 mm
(2”)
57 mm
(2-1/4”)
102 mm
(4”)
114 mm
(4-1/2”)
13 mm
(1/2”)
13 mm
(1/2”)
51 mm
(2”)
57 mm
(2-1/4”)
13 mm
(1/2”)
14 mm
(9/16”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
65 mm
(2-9/16”)
127 mm
(5”)
13 mm
(1/2”)
57 mm
(2-1/4”)
16 mm
(5/8”)
38 mm
(1-1/2”)
38 mm
(1-1/2”)
32 mm
(1-1/4”)
45 mm
(1-3/4”)
83 mm
(3-1/4”)
13 mm
(1/2”)
45 mm
(1-3/4”)
13 mm
(1/2”)
27
Fig. 13
ADVERTENCIA
Fig. 15
Fig. 12
28
MANTENIMIENTO
29
30
UNITED STATES
MILWAUKEE Service
MILWAUKEE prides itself in producing a premium
quality product that is NOTHING BUT HEAVY DUTY®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, or you would like to locate the
factory Service/Sales Support Branch or authorized
service station nearest you, please call...
Additionally, we have a nationwide network of
authorized Distributors ready to assist you with
your tool and accessory needs. Check your “Yellow
Pages” phone directory under “Tools-Electric” for
the names & addresses of those nearest you or see
the 'Where To Buy' section of our website.
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday
7:00 AM - 6:30 PM
Central Time
or visit our website at
www.milwaukeetool.com
For service information, use the 'Service Center
Search' icon found in the 'Parts & Service' section.
Contact our Corporate After Sales Service
Technical Support about ...
•Technical Questions
•Service/Repair Questions
•Warranty
call: 1-800-SAWDUST
fax: 1.800.638.9582
email: metproductsupport@milwaukeetool.com
Register your tool online at
www.milwaukeetool.com and...
• receive important notifications regarding
your purchase
• ensure that your tool is protected under the
warranty
• become a HEAVY DUTY club member
CANADA - Service MILWAUKEE
MILWAUKEE prides itself in producing a premium
quality product that is NOTHING BUT HEAVY DUTY®.
Your satisfaction with our products is very important to us!
If you encounter any problems with the operation
of this tool, or you would like to locate the factory
Service/Sales Support Branch or authorized service station nearest you, please call...
1.800.268.4015
Monday – Friday 7:00 – 4:30 CST
fax: 866.285.9049
Milwaukee Electric Tool (Canada) Ltd
140 Fernstaff Court, Unit 4
Vaughan, ON L4K 3L8
18129 111 Avenue NW
Edmonton, AB T5S 2P2
Additionally, we have a nationwide network of
authorized Distributors ready to assist you with your
tool and accessory needs. Call 1.800.268.4015 to
find the names and addresses of the closest retailers or consult “Where to buy” on our Web site
www.milwaukeetool.com
1.800.268.4015
Lundi – Vendredi 7:00 – 4:30 CST
fax: 866.285.9049
Milwaukee Electric Tool (Canada) Ltd
140 Fernstaff Court, Unit 4
Vaughan, ON L4K 3L8
18129 111 Avenue NW
Edmonton, AB T5S 2P2
www.ttigroupmexico.com
MILWAUKEE ELECTRIC TOOL CORPORATION
58-14-3347d15
13135 West Lisbon Road • Brookfield, Wisconsin, U.S.A. 53005
10/13
Printed in China
960931389-04( )
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising

Languages

Only pages of the document in English were displayed