DeWalt DC725-XE Datasheet

DeWalt DC725-XE Datasheet
DC725, DC735, DC745
CORDLESS COMPACT COMBI DRILLS
Figure 1
d
c
f
e
b
a
g
h
Figure 2
h
g
i
Figure 3
B
A
Figure 4
c
Figure 5
c
Figure 6
c
1006323-02
02/08
Technical data*
Voltage
Battery Type
Power output
No-load speed
1st gear
2nd gear
Impact rate
1st gear
2nd gear
Max. torque
Chuck capacity
Maximum drilling capacity
Wood
Metal
Masonry
VDC
W
min-1
min-1
DC725
18
NiCd
400
0–500
0–1700
DC735
14.4
NiCd
295
DC745
12
NiCd
240
0–400
0–1450
min-1
min-1
Nm
mm
0-8500
0–29000
44
13
0-6800
0–25000
mm
mm
mm
38
13
13
35
13
13
0–400
0–1450
0-6800
0–25000
40
13
35
13
28
13
13
* NOTE: NOT ALL MODELS ARE AVAILABLE IN ASIA. CHECK WITH AUTHORISED DEWALT AGENT
CHARGER TYPE: DE9116-KR USED IN ALL MODELS.
DEWALT reserves the right to change the content of the above tools without notice.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
1) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
3) PERSONAL SAFETY
a)
b)
Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
Do not overreach. Keep proper
footing and balance at all times.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer.
b)
Use power tools only with specifically
designated battery packs.
c)
When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d)
Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Charging Procedure
1. Plug the charger (j) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (h) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
Important Safety Instructions for All
Battery Chargers
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DEWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Under certain conditions,
with the charger plugged in to the
power supply, the exposed charging
contacts inside the charger can be
shorted by foreign material.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DEWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger.
• Do not use an extension cord unless it
is absolutely necessary.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat.
• Do not operate charger with damaged cord
or plug
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way.
• Do not disassemble charger; take it to an
authorized service center when service or
repair is required.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
Charging process
Refer the table below for the state of charge of the
battery pack.
State of charge
charging
fully charged
hot/cold pack delay
replace battery pack
problem
– – – – – –
–––––––––––
––– – ––– –
•••••••••••
•• •• •• ••
Automatic refresh
The automatic refresh mode will equalise or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed weekly
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery in the
charger as usual. Leave the battery pack for at least
8 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
Important Safety Instructions for All
Battery Packs
• Charge the battery packs only in DEWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40˚ C (105° F)
DANGER: Electrocution hazard. Never
attempt to open the battery pack for
any reason.
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged, do
not insert into charger. Do not crush,
drop or damage battery pack. Do not
use a battery pack or charger that has
received a sharp blow, been dropped,
run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer,
stepped on).
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
• A small leakage of liquid from the battery
pack cells may occur under extreme usage
or temperature conditions . This does not
indicate a failure.
However, if the outer seal is broken:
a. and the battery liquid gets on your skin,
immediately wash with soap and water for
several minutes.
b. and the battery liquid gets into your eyes,
flush them with clean water for a minimum
of 10 minutes and seek immediate medical
attention. (Medical note: The liquid is
25-35% solution of potassium hydroxide.)
Battery Cap (fig. 3)
A protective battery cap is supplied to cover the
contacts of a detached battery pack. Without the
protective cap in place, loose metal objects could
short circuit the contacts, causing a fire hazard and
damaging the battery pack.
1. Take off the protective battery cap before
placing the battery pack in the charger
or tool (Fig. 3A).
2. Place the protective cap over the contacts
immediately after removing the battery pack
from the charger or tool (Fig. 3B).
WARNING: Make sure the protective
battery cap is in place before storing or
carrying a detached battery pack.
Battery pack (fi g. 1)
BATTERY TYPE
Each tool described in this manual uses different battery
platforms within the DEWALT battery system.
Users of existing 12V, 14.4V & 18V batteries can use their
packs on the relevant tools in this manual.
Performance & run time may vary slightly on pack used.
Labels on charger and battery pack
Package contents
Torque Adjustment Collar (fig. 1)
The package contains:
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array of
fastener shapes and sizes and in some models, a
hammer mechanism for drilling into masonry. Circling
the collar (c) are numbers, a drill bit symbol, and in
some models, a hammer symbol. These numbers
are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the
torque and the larger the fastener which can be
driven. To select any of the numbers, rotate until the
desired number aligns with the arrow.
1 Drill/Hammerdrill
2 Battery packs
1 Charger
1 Kitbox (K version only)
1 Instruction manual
1 Exploded drawing
NOTE : Battery packs and chargers are not included
with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
INTENDED USE
These drills/drivers/hammerdrills are designed for
professional drilling and screwdriving applications.
Worklight (fig. 1)
a. Trigger switch
b. Forward/reverse button
c. Torque adjustment collar
d. Gear selector
e. Worklight
f. Keyless chuck
g. Battery pack
h. Battery release buttons
Inserting and removing the
battery pack from the tool (fi
g. 2)
WARNING: To reduce the risk of
serious personal injury, turn tool off
and disconnect battery pack
before
making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
TO INSTALL BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle (fig. 2).
Battery charged.
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with D E WALT battery packs,
others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 °C and 40 °C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack
NiMH, NiCd+ and Li-Ion.
Charges NiMH and NiCd
battery packs.
To select the low speed, high torque setting, turn
the tool off and permit to stop. Slide the gear
selector (d) forward (towards the chuck) as shown
in Figure 1.
To select the high speed, low torque setting, turn the
tool off and permit to stop. Slide the gear selector
back (away from chuck).
Description (fig. 1)
Battery charging.
Battery defective.
Dual Range Gearing (fig. 1)
TO REMOVE BATTERY PACK FROM THE TOOL
1. Press the battery release buttons (h) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Variable Speed Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off , release the trigger switch. Your
tool is equipped with a brake. The chuck will stop as
soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock off
button.
To select forward rotation, release the trigger
switch and depress the forward/reverse control
button on the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
There is a worklight (e) located just above the trigger
switch (a). The worklight will be activated when the
trigger switch is squeezed.
Keyless Single Sleeve Chuck (fig. 1)
1. Lock the trigger in the OFF position as
previously described.
2. Grasp the black sleeve of the chuck with one
hand and use the other hand to secure the tool.
Rotate the sleeve counterclockwise far enough
to accept the desired accessory.
3. Insert the accessory about 19 mm into the
chuck and tighten securely by rotating the
chuck sleeve clockwise with one hand while
holding the tool with the other. Your tool is
equipped with an automatic spindle lock
mechanism. This allows you to open and close
the chuck with one hand.
To release the accessory, repeat step 2 above.
Hammerdrill Operation (fi g. 5)
1. Turn the collar (c) to the hammerdrill symbol.
2. Select the high speed setting by sliding the
selector back (away from the chuck).
IMPORTANT:
bits only.
Use carbide-tipped or masonry
Screwdriver Operation (fig. 6)
1. Select the desired speed/torque range using the
dual range gear selector to match the speed
and torque of the planned operation.
2. Turn the torque adjustment collar to the desired
position. Lower numbers indicate lower torque
settings; higher numbers indicate higher torque
settings.
MAINTENANCE
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Separate collection. This product must
not be disposed of with normal
household waste.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
DC735
18
14.4
NiCd
NiCd
400
295
0-500
0-400
0-1700 0-1450
0-8500
0-29000 0-25000
전압 V
DC
W
타격
최대토크
Nm
44
척
mm
13
0-6800
40
13
mm
38
35
철재
mm
13
13
석재
mm
13
13
1)
전기 안전
a)
b)
c)
2)
개인 안전
3)
e)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed