AEG Electrolux S71700TSW0 User manual

AEG Electrolux S71700TSW0 User manual
S71700TSW0
NL KOELKAST
EN REFRIGERATOR
FR RÉFRIGÉRATEUR
GEBRUIKSAANWIJZING
USER MANUAL
NOTICE D'UTILISATION
2
19
35
2
Bezoek onze webshop op
www.aeg-electrolux.com/shop
Inhoud
3
INHOUD
4
6
7
8
9
10
11
13
14
18
4
Veiligheidsinformatie
Veiligheidsinformatie
5
•
•
•
•
6
Bediening
7
8
9
10
Problemen oplossen
11
12
Oplossing
Zie 'De deur sluiten'.
Dit is normaal.
Er loopt water in de koelkast.
De waterafvoer is verstopt.
Er loopt water over de
vloer.
De deur is niet goed gesloten.
Zie 'De deur sluiten'.
Technische gegevens
Probleem
13
Oplossing
TECHNISCHE GEGEVENS
Afmeting
Hoogte
850 mm
595 mm
Diepte
635 mm
14
Montage
Omgevingstemperatuur
SN
+10°C tot + 32°C
N
+16°C tot + 32°C
ST
+16°C tot + 38°C
T
+16°C tot + 43°C
1
2
15mm
15mm
100mm
Montage
15
m
200 c
3
93-10
A
105
570
550
820 min
/600
/550
500
2
16
6.
Montage
17
18
19
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have
created it to give you impeccable performance for many
years, with innovative technologies that help make life
simpler – features you might not find on ordinary
appliances. Please spend a few minutes reading to get
the very best from it.
ACCESSORIES AND CONSUMABLES
In the AEG webshop, you’ll find everything you need to
keep all your AEG appliances looking spotless and
working perfectly. Along with a wide range of
accessories designed and built to the high quality
standards you would expect, from specialist cookware
to cutlery baskets, from bottle holders to delicate
laundry bags…
Visit the webshop at:
www.aeg-electrolux.com/shop
20
Contents
CONTENTS
21
23
24
24
25
26
28
30
30
34
Safety information
Operation
First use
Daily use
Helpful hints and tips
Care and cleaning
What to do if…
Technical data
Installation
Environmental concerns
The following symbols are used in this user
manual:
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice
Safety information
21
SAFETY INFORMATION
In the interest of your safety and to ensure the correct use, before installing and first
using the appliance, read this user manual carefully, including its hints and warnings. To
avoid unnecessary mistakes and accidents, it is important to ensure that all people using
the appliance are thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they remain with the appliance if it is moved or sold, so
that everyone using it through its life will be properly informed on appliance use and
safety.
For the safety of life and property keep the precautions of these user's instructions as the
manufacturer is not responsible for damages caused by omission.
Children and vulnerable people safety
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from children. There is risk of suffocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection
cable (as close to the appliance as you can) and remove the door to prevent playing
children to suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having
a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death trap for
a child.
General safety
CAUTION!
Keep ventilation openings clear of obstruction.
• The appliance is intended for keeping foodstuff and/or beverages in a normal household as explained in this instruction booklet.
• Do not use a mechanical device or any artificial means to speed up the thawing process.
• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, be certain that none of the
components of the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
22
Safety information
– avoid open flames and sources of ignition
– thoroughly ventilate the room in which the appliance is situated
• It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock.
WARNING!
Any electrical component (power cord, plug, compressor) must be replaced by a certified
service agent or qualified service personnel.
•
•
•
•
1. Power cord must not be lengthened.
2. Make sure that the power plug is not squashed or damaged by the back of the
appliance. A squashed or damaged power plug may overheat and cause a fire.
3. Make sure that you can come to the mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance without the lamp cover5) of interior lighting.
This appliance is heavy. Care should be taken when moving it.
Do not remove nor touch items from the freezer compartment if your hands are
damp/wet, as this could cause skin abrasions or frost/freezer burns.
Avoid prolonged exposure of the appliance to direct sunlight.
Bulb lamps6) used in this appliance are special purpose lamps selected for household
appliances use only. They are not suitable for household room illumination.
Daily use
• Do not put hot pot on the plastic parts in the appliance.
• Do not store flammable gas and liquid in the appliance, because they may explode.
• Appliance's manufacturers storage recommendations should be strictly adhered to.
Refer to relevant instructions.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug from the
mains socket.
• Do not clean the appliance with metal objects.
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean
the drain. If the drain is blocked, water will collect in the bottom of the appliance.
Installation
For electrical connection carefully follow the instructions given in specific paragraphs.
• Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought
it. In that case retain packing.
5) If the lamp cover is foreseen.
6) If the lamp is foreseen.
Operation
23
• It is advisable to wait at least four hours before connecting the appliance to allow the
oil to flow back in the compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
• Wherever possible the back of the product should be against a wall to avoid touching
or catching warm parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
• Connect to potable water supply only. 7)
Service
• Any electrical work required to do the servicing of the appliance should be carried out
by a qualified electrician or competent person.
• This product must be serviced by an authorized Service Centre, and only genuine spare
parts must be used.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The appliance shall not be discarded together
with the urban refuse and rubbish. The insulation foam contains flammable gases: the
appliance shall be disposed according to the applicable regulations to obtain from your
local authorities. Avoid damaging the cooling unit, especially at the rear near the heat
exchanger. The materials used on this appliance marked by the symbol are recyclable.
OPERATION
Switching on
Insert the plug into the wall socket.
Turn the Temperature regulator clockwise to a medium setting.
Switching off
To turn off the appliance, turn the Temperature regulator to the "O" position.
Temperature regulation
The temperature is automatically regulated.
To operate the appliance, proceed as follows:
• turn the Temperature regulator toward lower settings to obtain the minimum coldness.
• turn the Temperature regulator toward higher settings to obtain the maximum coldness.
A medium setting is generally the most suitable.
7) If a water connection is foreseen.
24
First use
However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on:
• room temperature
• how often the door is opened
• the quantity of food stored
• the location of the appliance.
If the ambient temperature is high or the appliance is fully loaded, and the appliance is
set to the lowest temperatures, it may run continuously causing frost to form on the
rear wall. In this case the dial must be set to a higher temperature to allow automatic
defrosting and therefore reduced energy consumption.
FIRST USE
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a
brand-new product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
DAILY USE
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be positioned as desired.
this appliance is sold in France.
In accordance with regulations valid in this country it must be provided with a special
device (see figure) placed in the lower compartment of the fridge to indicate the coldest
zone of it.
Helpful hints and tips
25
Positioning the door shelves
To permit storage of food packages of various
sizes, the door shelves can be placed at different
heights.
To make these adjustments proceed as follows:
gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as required.
HELPFUL HINTS AND TIPS
Normal Operating Sounds
• You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped
through the coils or tubing. This is correct.
• When the compressor is on, the refrigerant is being pumped around and you will hear
a whirring sound and a pulsating noise from the compressor. This is correct.
• The thermic dilatation might cause a sudden cracking noise. It is natural, not dangerous physical phenomenon. This is correct.
• When the compressor switches on or switches off, you will hear a faint "click" of the
temperature regulator. This is correct.
Hints for energy saving
• Do not open the door frequently or leave it open longer than absolutely necessary.
26
Care and cleaning
• If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously,
causing frost or ice on the evaporator. If this happens, set the Temperature Regulator
toward warmer settings to allow automatic defrosting and so a saving in electricity
consumption.
Hints for fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liquids in the refrigerator
• do cover or wrap the food, particularly if it has a strong flavour
• position food so that air can circulate freely around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in
aluminium foil or polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
CARE AND CLEANING
CAUTION!
Unplug the appliance before carrying out any maintenance operation.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging
must therefore only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water and some neutral soap.
• regularly check the door seals and wipe clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as this will damage the surface and leave a strong odour.
Care and cleaning
27
Clean the condenser (black grill) and the compressor at the back of the appliance with a
brush or a vacuum cleaner. This operation will improve the performance of the appliance
and save electricity consumption.
Take care of not to damage the cooling system.
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it is recommended that the outer casing of
this appliance is only cleaned with warm water with a little washing-up liquid added.
After cleaning, reconnect the equipment to the mains supply.
Defrosting of the refrigerator
Frost is automatically eliminated from the evaporator of the refrigerator compartment
every time the motor compressor stops, during normal use. The defrost water drains out
through a trough into a special container at the back of the appliance, over the motor
compressor, where it evaporates.
It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator compartment channel to prevent the water
overflowing and dripping onto the food inside.
Use the special cleaner provided, which you will
find already inserted into the drain hole.
Periods of non-operation
When the appliance is not in use for long periods, take the following precautions:
1. disconnect the appliance from electricity supply
2. remove all food
3. defrost and clean the appliance and all accessories
4. leave the door/doors open to prevent unpleasant smells.
If the cabinet will be kept on, ask somebody to check it once in a while to prevent the
food inside from spoiling in case of a power failure.
28
What to do if…
WHAT TO DO IF…
WARNING!
Before troubleshooting, disconnect the mains plug from the mains socket.
Only a qualified electrician or competent person must do the troubleshooting that is not
in this manual.
There are some sounds during normal use (compressor, refrigerant circulation).
Problem
Solution
The appliance is noisy
The appliance is not supported
properly
Check if the appliance stands
stable (all the four feet should be
on the floor)
The appliance does not
operate. The lamp does
not operate.
The appliance is switched off.
Switch on the appliance.
The mains plug is not connected to the mains socket correctly.
Connect the mains plug to the
mains socket correctly.
The appliance has no power.
Connect a different electrical
There is no voltage in the mains appliance to the mains socket.
socket.
Contact a qualified electrician.
The lamp does not work.
The compressor operates
continually.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Refer to "Replacing the lamp".
The temperature is not set correctly.
Set a higher temperature.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too
frequently.
Do not keep the door open longer than necessary.
The product temperature is too
high.
Let the product temperature decrease to room temperature before storage.
The room temperature is too
high.
Decrease the room temperature.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting process, frost defrosts on
the rear plate.
This is correct.
Water flows into the refrigerator.
The water outlet is clogged.
Clean the water outlet.
Products prevent that water
flows into the water collector.
Make sure that products do not
touch the rear plate.
What to do if…
Problem
29
Solution
Water flows on the
ground.
The melting water outlet does
Attach the melting water outlet
not flow in the evaporative tray to the evaporative tray.
above the compressor.
The temperature in the
appliance is too low.
The temperature regulator is
not set correctly.
Set a higher temperature.
The temperature in the
appliance is too high.
The temperature regulator is
not set correctly.
Set a lower temperature.
The door is not closed correctly. Refer to "Closing the door".
The temperature in the
refrigerator is too high.
The product temperature is too
high.
Let the product temperature decrease to room temperature before storage.
Many products are stored at
the same time.
Store less products at the same
time.
There is no cold air circulation
in the appliance.
Make sure that there is cold air
circulation in the appliance.
Replacing the lamp
1. Disconnect the mains plug from the mains socket.
2. Remove the screw from the lamp cover.
3. Remove the lamp cover (refer to the illustration).
4. Replace the used lamp with a new lamp
of the same power and specifically designed for household appliances. (the
maximum power is shown on the lamp
cover).
5. Install the lamp cover.
6. Tighten the screw to the lamp cover.
7. Connect the mains plug to the mains socket.
8. Open the door. Make sure that the lamp comes on.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to "Installation".
3. If necessary, replace the defective door gaskets. Contact the Service Center.
30
Technical data
TECHNICAL DATA
Dimension
Height
850 mm
Width
595 mm
Depth
635 mm
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
INSTALLATION
WARNING!
Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Positioning
This appliance can be installed in a dry, well ventilated indoor (garage or cellar) also, but
for optimum performance install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:
Climate class
Ambient temperature
SN
+10°C to + 32°C
N
+16°C to + 32°C
ST
+16°C to + 38°C
T
+16°C to + 43°C
Levelling
When placing the appliance ensure that it
stands level. This can be achieved by two adjustable feet at the bottom in front (2). If necessary
adjust the feet by removing the spacer (1).
1
2
Installation
31
Location
15mm
15mm
100mm
The appliance should be installed well away
from sources of heat such as radiators, boilers,
direct sunlight etc. Ensure that air can circulate
freely around the back of the cabinet.To ensure
best performance, if the appliance is positioned
below an overhanging wall unit, the minimum
distance between the top of the cabinet and the
wall unit must be at least 100 mm . Ideally,
however, the appliance should not be positioned
below overhanging wall units. Accurate levelling
is ensured by one or more adjustable feet at the
base of the cabinet. If the cabinet is placed in a
corner and the side with the hinges facing the
wall, the distance between the wall and the cabinet must be at least 10 mm to allow the
door to open enough so that the shelves can be removed.
WARNING!
It must be possible to disconnect the appliance from the mains power supply; the plug
must therefore be easily accessible after installation.
Installing under a continuous worktop
2
m
200 c
3
93-10
A
105
570
550
/600
/550
500
820 min
If your refrigerator is installed under a continuous worktop, an air outlet opening of at least
200cm2 and a ventilation grille matching the
worktop design should be installed at the rear of
the worktop.
The cut surfaces of the worktop should be varnished to avoid swelling due to penetration of
moisture.
The appliance wall distance must be at least 30
mm and should be checked before the ventilation grille is inserted.
32
Installation
Detaching the worktop
To remove the worktop, please proceed as follows:
1. Unscrew left and right screws at the front.
2. Unscrew left and right screws at the back.
3. Lift the worktop slightly at the front, push
back about 20 mm and lift off from the
front.
4. Unscrew left and right screws at the back.
5. Store the screws in a safe place together
with the worktop.
3
3
1
2
4
5
Fitting and mounting to continuous worktop
Before fitting, change the door opening direction if necessary (see: Door reversibility).
Push the appliance carefully into the niche.
Take care that the mains cable is not jammed in.
Check distance from wall (see: Installing under a
continuous worktop).
Level the appliance by screwing the two adjustable feet at the front in or out, thus ensuring a
stable position.
With a suitable screws (depending on the design
of the worktop and the distance between the appliance and the worktop, not supplied),
fix the appliance under the worktop through the upper door hinge. If necessary, equalise
the gap between the door hinge and the worktop with a suitable washer (plastic or
wood, not supplied). This will prevent bending of the hinge and possible failure of door
function.
Door reversibility
To carry out the following operations, we suggest that this be made with another person
that will keep a firm hold on the doors of the appliance during the operations.
To change the opening direction of the door, do these steps:
1. Remove the plug from the power socket.
2. Tilt back the appliance carefully so that the compressor cannot touch the floor.
Installation
3.
4.
5.
33
Unscrew both adjustable feet.
Unscrew the screws of the door bottom hinge.
Take off the appliance door by pulling
it slightly downwards.
6.
Unscrew the top door hinge pin of the
appliance then screw it back on the
other side.
7. Fit the appliance door on the upper
door hinge pin.
8. Remove the lower hinge. Put over the
pin in the direction of the arrow.
9. Unscrew and install the screw on the
opposite side.
10. Install the lower hinge on the opposite
side leaving the position of the door
unchanged.
11. Screw in the one screw in the place set free on the other side as well as the adjustable feet (2 pieces).
12. Remove and install the handle8) on the
opposite side.
13. Reposition, level the appliance, wait for
at least four hours and then connect it
to the power socket.
Do a final check to make sure that:
• All screws are tightened.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural fitting of the gasket.
In case you do not want to carry out the above mentioned operations, contact the nearest After Sales Service Force. The After Sales Service specialist will carry out the reversibility of the doors at your cost.
8) If foreseen
34
Environmental concerns
Plug socket
CAUTION!
Make sure that the mains cable can move freely.
The plug socket necessary for connection of your
appliance to the electricity supply should be
positioned so that it is possible to pull out the
appliance plug.
If your appliance is installed under a continuous
worktop, the plug socket should be provided as
shown.
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating plate
correspond to your domestic power supply.
The appliance must be earthed. The power supply cable plug is provided with a contact
for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified
electrician.
The manufacturer declines all responsibility if the above safety precautions are not observed.
This appliance complies with the E.E.C. Directives.
ENVIRONMENTAL CONCERNS
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection
point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about recycling of this
product, please contact your local council, your household waste disposal service or the
shop where you purchased the product.
35
36
SOMMAIRE
37
42
43
43
45
46
47
37
38
39
•
•
•
•
40
41
42
43
44
OK
45
46
47
48
Solution
Nettoyez l'orifice.
49
Solution
5.
6.
7.
8.
50
850 mm
595 mm
635 mm
SN
N
ST
T
1
2
Installation
51
15mm
15mm
100mm
m
200 c
3
93-10
A
105
570
550
/600
/550
500
820 min
52
Installation
3
3
1
2
4
5
Installation
3.
4.
5.
53
6.
54
55
www.aeg-electrolux.com/shop
200383592-A-352010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed