Campbell Hausfeld IN203203AV 11/00 Operating instructions

Campbell Hausfeld IN203203AV 11/00 Operating instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the
product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could
result in personal injury and/or property damage! Retain instructions for future reference.
TM
BUILT TO LAST
Description
STOP!
Oilless compressors are designed for
do-it-yourselfers with a variety of home
and automotive jobs. These
compressors power spray guns, impact
wrenches and other tools. These units
operate without oil.
Oilless
Compressors
DO NOT RETURN THE
PRODUCT TO THE
RETAILER!
Record the Model No., Serial No. and
date of purchase located on the base
below the pump in the space below.
Danger indicates
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
Model No. ____________________
Warning indicates
a potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
Retain these numbers for future
reference.
!
DANGER
! WARNING
Caution indicates a
!
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
CAUTION
Notice indicates
important
information, that if not followed, MAY
cause damage to equipment.
NOTICE
Unpacking
After unpacking the unit, inspect
carefully for any damage that may have
occurred during transit. Make sure to
tighten fittings, bolts, etc., before
putting unit into service. In case of
questions, damaged or missing parts,
please call 1-800-543-6400 for customer
© 2000 Campbell Hausfeld
Serial No. ____________________
Date of purchase _________________
assistance or call the nearest Campbell
Hausfeld Authorized Service Center.
A listing of service center locations is
enclosed. Have the serial number,
model number, and parts list (with
missing parts circled before calling.
Do not operate
! WARNING unit if damaged
during shipping, handling or use.
Damage may result in bursting and
cause injury or property damage.
General Safety
Information
Since the air compressor and other
components (material pump, spray
guns, filters, lubricators, hoses, etc.)
used, make up a high pressure
pumping system, the following safety
For parts, product & service information
visit www.chpower.com
24
Need
Assistance?
Call Us First!
1-800-543-8622
DANGER
Breathable Air Warning
Safety Guidelines
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols.
!
SSURANCE PR
YA
RAM
OG
WL Series
Operating Instructions
IT
Serie WL
QUAL
Compresores Sin Aceite
This compressor/pump is not
equipped and should not be used
“as is” to supply breathing quality
air. For any application of air for
human consumption, the air
compressor/pump will need to be
fitted with suitable in-line safety
and alarm equipment. This
additional equipment is necessary
to properly filter and purify the air
to meet minimal specifications for
Grade D breathing as described in
Compressed Gas Association
Commodity Specification G 7.1 1966, OSHA 29 CFR 1910. 134,
and/or Canadian Standards
Associations (CSA).
DISCLAIMER OF WARRANTIES
In the event the compressor is used
for the purpose of breathing air
application and proper in-line
safety and alarm equipment is not
simultaneously used, existing
warranties shall be voided, and
Campbell Hausfeld disclaims any
liability whatsoever for any loss,
personal injury or damage.
precautions must be observed at all
times:
1. Read all manuals
included with this
product carefully. Be
MANUAL
thoroughly familiar
with the controls and
the proper use of the equipment.
2. Follow all local electrical and safety
codes as well as in the US, National
Electrical Codes (NEC) and Occupational
Safety and Health Act (OSHA).
IN203203AV 11/00
General Safety
Information (Continued)
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.
4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and use hearing
protection when operating the
pump or unit.
6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
! WARNING
Motors, electrical
equipment and controls
can cause electrical arcs
that will ignite a flammable gas or
vapor. Never operate or repair in or
near a flammable gas or vapor. Never
store flammable liquids or gases in the
vicinity of the compressor.
!
CAUTION
Compressor parts may
be hot even if the unit
is stopped.
9. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
10. If the equipment should start to
abnormally vibrate, STOP the
engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
11. To reduce fire hazard, keep
engine/motor exterior free of oil,
solvent, or excessive grease.
Never remove or
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
! WARNING
!
DANGER
Never attempt to repair
or modify a tank!
Serie WL
Welding, drilling or any other
modification will weaken the tank
resulting in damage from rupture or
explosion. Always replace worn or
damaged tanks.
NOTICE
Drain liquid from
tank daily.
13. Tanks rust from moisture build-up,
which weakens the tank. Make sure
to drain tank regularly and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
14. Fast moving air will stir up dust and
debris which may be harmful. Release
air slowly when draining moisture or
depressurizing the compressor system.
SPRAYING PRECAUTIONS
! WARNING
Do not spray flammable
materials in vicinity of
open flame or near
ignition sources including the
compressor unit.
15. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
16. Use a face mask/
respirator when
spraying and spray in
a well ventilated area
to prevent health and
fire hazards.
17. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.
18. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
2. Place a short piece of wood against
end of handle and tap it with a
mallet or hammer to drive handle
into baseplate until hole in handle
and baseplate line up (See Fig. 1).
1. Insert handle into both sides of tank
baseplate at motor end. Handle must
fit into special openings in baseplate
and must be squeezed by hand to fit.
Posible(s) Causa(s)
PELIGRO
Rubber
Foot
Figure 1
3. Assemble and tighten screw (from
parts package) through hole in baseplate ensuring it goes through handle.
1. El presostato está dañado
2. Consumo excesivo de aire
Never use the
!
handle to lift the
unit completely off the ground. Only
use the handle to lift one end so the
wheels may be used to move the unit.
WARNING
4. Spread openings in the rubber feet
and slip over ground iron. Position
the feet as shown in Fig. 1.
WHEEL ASSEMBLY
The items marked with an asterisk (*)
were shipped loose with the unit.
1. Insert shoulder bolt through wheel
hub. The bolt hex head should be
on the opposite side of protruding
hub center.
2. For 8 inch diameter wheels, feed
the shoulder bolt through the
bottom hole on the tank axle iron
and tightly secure with the locknut.
For 10 inch diameter wheels, feed
the shoulder bolt through the top
hole on the tank axle iron and
tightly secure with the locknut.
Assembly
Compressor handle has a notch (or
detent) at top of handle. This notch
provides a handy place to hang a spray
gun, sandblast gun, or other tool
equipped with a hook.
PELIGRO
!
Shoulder
bolt
* Lock nut
* Wheel
Figure 2 - Wheel Assembly
www.chpower.com
2
23 Sp
PELIGRO
Compresores Sin Aceite
WL Series
Assembly (Con't)
El compressor no
funciona
PELIGRO
PELIGRO
Repeat on the opposite side.
3. When assembled, the tank must sit
level or slope slightly towards the
drain cock to allow the tank to
drain properly.
Installation
LOCATION
It is extremely important to install the
compressor in a clean, well ventilated area
where the surrounding air temperature
will not be more than 100°F.
A minimum clearance of 18 inches
between the compressor and a wall is
required because objects could
obstruct air flow.
Do not locate the
compressor air
inlet near steam, paint spray, sandblast
areas or any other source of
contamination. This debris will damage
the motor.
!
2. Reemplácela o repárela
PRECAUCION
!
PELIGRO
PELIGRO
CAUTION
All wiring and
!
electrical
connections should be performed by a
qualified electrician. Installation must be
in accordance with local codes and
national electrical codes.
WARNING
!
CAUTION
Never use an extension
STOP!
cord with this product. Use
additional air hose instead
of an extension cord to
avoid power loss and permanent motor
damage. Use of an extension cord voids
the warranty.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks like the plug illustrated
in Fig. 3. Make sure the product is
connected to an outlet having the
same configuration as the plug. This
product must be grounded. In the
event of an electrical short circuit,
grounding reduces risk of electrical
shock by providing an escape wire for
electric current. This product is
equipped with a cord having a
grounding wire with an appropriate
grounding plug. Plug must be plugged
into an outlet that is properly installed
and grounded in accordance with all
local codes and ordinances.
Grounding
Pin
TEST
RESET
Grounded Outlet
Figure 3 - Grounding Method
!
DANGER
Improper use of grounding
plug can result in a
possible risk of electrical
shock!
!
DANGER
Do not use a
grounding adapter
with this product!
2. If repair or replacement of cord or plug
is necessary, do not connect grounding
wire to either flat blade terminal. The
wire with insulation having an external
surface that is green (with or without
yellow stripes) is the grounding wire.
Never connect
! WARNING green (or green and
yellow) wire to a live terminal.
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or if in
doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.
WIRING
1. Local electrical wiring codes differ from
area to area. Source wiring, plug and
protector must be rated for at least the
amperage and voltage indicated on
motor nameplate, and meet all electrical
codes for this minimum.
2. Use a slow blow fuse or a circuit
breaker.
Overheating, short
!
circuiting and fire
damage will result from inadequate
wiring, etc.
CAUTION
NOTE: 120 volt, 15 amp units can be
operated on a 120 volt circuit under the
following conditions:
a. No other electrical appliances or lights
are connected to the same branch
circuit.
b. Voltage supply is normal.
c. Circuit is equipped with a 15 amp
circuit breaker or a 15 amp slow blow
fuse.
3. If these conditions cannot be met or if
nuisance tripping of current
protection device occurs, it may be
necessary to operate compressor from
a 120 volt, 20 amp circuit.
Operation
Pressure Switch - Auto/Off Switch - In
the AUTO position, the compressor
shuts off automatically when tank
pressure reaches the maximum preset
pressure. In the OFF position, the
compressor will not operate. This
switch should be in the OFF position
when connecting or disconnecting the
power cord from the electrical outlet
or when changing air tools.
Regulator - The regulator controls the
amount of air pressure released at the
hose outlet.
ASME Safety Valve - This valve
automatically releases air if the tank
pressure exceeds the preset maximum.
Discharge Tube - This tube carries
compressed air from the pump to the
check valve. This tube becomes very
hot during use. To avoid the risk of
severe burns, never touch the
discharge tube.
Check Valve - A one-way valve that
allows air to enter the tank, but
prevents air in the tank from flowing
back into the compressor pump.
Handle - Designed to move the
compressor.
Never use the
!
handle on wheeled
units to lift the unit completely off the
ground.
WARNING
Drain Petcock - This valve is located on
the bottom of the tank. Use this valve
to drain moisture from the tank daily
to reduce the risk of corrosion.
Reduce tank pressure below 10 PSI,
then drain moisture from tank daily to
avoid tank corrosion. Drain moisture
www.chpower.com
22 Sp
3
Serie WL
Operation (Continued)
Discharge Tube
(Opposite Side)
Check Valve
(Opposite Side)
(Continuacíon)
from tank(s) by opening the drain
petcock located underneath the tank.
Pressure
Switch
LUBRICATION
This is an oilless product and DOES
NOT require lubrication to operate.
Regulator
Handle
BREAK-IN PROCEDURE
Air Hose
Attachment
Do not attach air
!
chuck or other tool
to open end of hose until start-up has
been completed and unit checks OK.
CAUTION
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will
form into droplets as it comes from
an air compressor pump. When
humidity is high or when a
compressor is in continuous use for
an extended period of time, this
moisture will collect in the tank.
When using a paint spray or
sandblast gun, this water will be
carried from the tank through the
hose, and out of the gun as
droplets mixed with the spray
material.
IMPORTANT: This condensation
will cause water spots in a paint
job, especially when spraying other
than water based paints. If
sandblasting, it will cause the sand
to cake and clog the gun,
rendering it ineffective. A filter in
the air line (MP3105), located as
near to the gun as possible, will
help eliminate this moisture.
Safety
Valve
Figura 7
Drain
Petcock
Figure 4 - Unit identification
released, or valve is stuck and cannot be
actuated by ring, it MUST be replaced.
Off
UT
A
IMPORTANT: Do not operate
compressor before reading instructions
or damage may result.
1. Turn regulator fully clockwise to
open air flow.
2. Turn switch or knob to OFF position
and plug in power cord.
3. Turn switch or knob to AUTO
position and run unit for 30 minutes
to break in the pump parts.
4. Turn regulator knob fully
counterclockwise. Compressor will
build to maximum preset pressure
and shut off.
O / OF
F
Auto
Figure 5 - Pressure Switch
5. Turn regulator knob clockwise to
cause air to bleed off. Compressor
will restart at a preset pressure.
6. Turn regulator knob
counterclockwise to shut off the air
and turn switch to Off position.
7. Attach chuck or other tool to open
end of hose. Turn the regulator on.
In the AUTO position, the compressor
pumps air into the tank. It shuts off
automatically when unit reaches its
maximum preset pressure. In the OFF
position, the pressure switch cannot
function and the compressor will not
operate. This switch should be in the
OFF position when connecting or
disconnecting the power cord from the
electrical outlet.
Figure 6
REGULATOR KNOB
1. This knob controls air pressure to an
air operated tool, or paint spray gun.
2. Turning knob clockwise increases air
pressure at outlet.
3. Turning counterclockwise will lower
air pressure at outlet.
Tank
Pressure
Gauge
Safety
Valve
Figure 7
the safety valve!
This valve should be checked under
pressure occasionally by pulling the ring
by hand. If air leaks after ring has been
2. Be sure this gauge reads ZERO before
changing air tools or disconnecting
hose from outlet.
! WARNING
Do not remove or
attempt to adjust
Válvula
de seguridad
!
ADVERTENCIA
!
ADVERTENCIA
Figura 8
!
PRECAUCION
PRECAUCION
www.chpower.com
4
Pressure Switch
Regulator
*Regulador
4. Fully counterclockwise will shut off
flow of air completely.
OUTLET PRESSURE GAUGE
1. This gauge shows at-a-glance, air
pressure at outlet. Air pressure is
measured in pounds per square inch
(psi).
ASME SAFETY VALVE
21 Sp
Compresores Sin Aceite
Regulador
ADVERTENCIA
PRECAUCION
UT
A
Mango
Presostato
Válvula de
seguridad
O / OF
F
If thermal overload protector shuts
motor OFF frequently, look for the
following causes.
Operation (Continued)
TANK PRESSURE GAUGE
Gauge shows pressure in tank
indicating compressor is building
pressure properly.
Maintenance
! WARNING
Disconnect power
source then release all
pressure from the
system before
attempting to install, service, relocate
or perform any maintenance.
The compressor should be checked
often for any visible problems and the
following maintenance procedures
should be performed each time the
compressor is used.
1. Pull ring on safety valve and allow it
to snap back to normal position.
Safety valve must
be replaced if it
cannot be actuated or it leaks air after
ring is released.
! WARNING
2. With compressor shut off and
pressure released: Drain moisture
from tank by opening drain cock
underneath tank.
1. Low voltage.
Figure 8
2. Clogged air filter.
3. Turn power OFF and clean dust and
dirt from motor, tank, air lines and
pump cooling fins.
IMPORTANT: Unit should be located as
far from spraying area as hose will
allow to prevent over-spray from
clogging filter.
AIR FILTER
Check air filter to be sure it is clean. To
service a filter, remove the filter
housing cover. Remove filter and clean
in hot, soapy water (Paper filters cannot
be washed). Rinse and let dry. Replace
air filters that cannot be cleaned. Place
filter back in the housing base. Replace
cover.
LUBRICATION
This is an oilless type compressor
requiring no lubrication.
THERMAL OVERLOAD PROTECTOR
This compressor is
!
equipped with an
automatic reset thermal overload
protector which will shut off motor if it
becomes overheated.
CAUTION
3. Lack of proper ventilation.
If the thermal
overload protector
is actuated, the motor must be allowed
to cool down before start-up is possible.
The motor will automatically restart
without warning if left plugged into
electrical outlet and unit is turned on.
!
CAUTION
TORQUE REQUIREMENTS
Connecting rod bolt . . . . . . . . 20 in. Ibs.
Compressor hd. bolts. . . 100-110 in. Ibs.
Motor bolts . . . . . . . . . . . . . . . 35 in. Ibs.
Mounting bolts . . . . . . . . . . . . 90 in. Ibs.
STORAGE
1. When not in use, hose and
compressor should be stored in a cool
dry place.
2. Tank should be drained of moisture.
3. Hose should be disconnected and
hung open, ends down, to allow any
moisture to drain.
Notes
Figura 5 - Presostato
!
ADVERTENCIA
www.chpower.com
20 Sp
5
Serie WL
Troubleshooting Chart
Possible Cause(s)
Corrective Action
Compressor will not run
1. No electrical power
2. Blown fuse
3. Breaker open
4. Thermal overload open
5. Pressure switch bad
6. Check valve defective
1. Plugged in? Check fuse/breaker or motor overload
2. Replace blown fuse
3. Reset, determine cause of problem
4. Motor will restart when cool
5. Replace
6. Remove and replace check valve
!
Motor hums but cannot
run or runs slowly
1. Poor contacts, line voltage incorrect
2. Shorted or open motor winding
3. Defective check valve or unloader
DANGER
Do not disassemble check valve
with air in tank; bleed tank
1. Check connections, check with voltmeter
2. Replace motor
3. Replace or repair
!
DANGER
!
(Continuacíon)
Symptom
Do not disassemble check valve
with air in tank; bleed tank
Perno
* Tuerca de
Fuses blow/circuit
breaker trips repeatedly
!
CAUTION
Never use an extension
cord with this product
1. Incorrect size fuse, circuit overloaded
2. Defective check valve or unloader
seguridad
1. Check for proper fuse, use time-delay fuse.
Disconnect other electrical appliances from circuit or
operate compressor on its own branch circuit
2. Replace or repair
!
DANGER
Do not disassemble check valve
with air in tank; bleed tank
PRECAUCION
COLOCACION
Thermal overload
protector cuts out
repeatedly
1. Low voltage
2. Clogged air filter
3. Lack of proper ventilation/room
temperature too high
4. Check valve malfunction
1. Check with voltmeter
2. Clean filter (see Maintenance section)
3. Move compressor to well ventilated area
!
DANGER
Do not disassemble check valve
with air in tank; bleed tank
!
Knocks, rattles,
excessive vibration
1. Leaking, broken, or loose valves or
restricted air passage
2. Defective pressure switch unloader
3. Defective bearing on eccentric or
motor shaft
4. Cylinder or piston ring is worn or
scored
5. Loose bolts, tank not level
1. Replace
2. Replace or repair as necessary
3. Replace
4. Replace or repair as necessary
5. Tighten bolts, shim tank to level position
PRECAUCION
!
ADVERTENCIA
TEST
RESET
!
PELIGRO
!
PELIGRO
!
ADVERTENCIA
www.chpower.com
6
ALTO!
19 Sp
!
PRECAUCION
Compresores Sin Aceite
3.
4.
5.
6.
7.
8.
!
ADVERTENCIA
!
PRECAUCION
ADVERTENCIA
!
PELIGRO
AVISO
diariamente.
!
ADVERTENCIA
Patas
de goma
Figura 1
!
ADVERTENCIA
Troubleshooting Chart (Continued)
Symptom
Corrective Action
Tank pressure drops
when compressor shuts
off
1. Loose connections (fittings, tubing,
etc.)
2. Loose drain cock
3. Check valve leaking
1. Check all connections with soap and water solution
and tighten
2. Tighten
3. Disassemble check valve assembly, clean or replace
!
DANGER
Do not disassemble check valve
with air in tank; bleed tank
1. Clogged intake filter
2. Air leaks in piping (on machine or in
outside system)
3. Broken inlet valves
4. Piston ring broken
5. Cylinder or piston ring is worn or
scored
1. Clean or replace
2. Replace leaking components or tighten as necessary
Excessive moisture in
discharge air
1. Excessive water in tank
2. High humidity
1. Drain tank
2. Move to area of less humidity; use air line filter
Compressor runs
continuously
1. Defective pressure switch
2. Excessive air usage
1. Replace switch
2. Decrease air usage; compressor not large enough for
air requirement
Excessive starting and
stopping (auto start)
1. Excessive condensation in tank
2. Air leaks in piping (on machine or in
outside system)
3. Tank check valve leaking
1. Drain more often
2. Replace leaking components or tighten as necessary
Air output lower than
normal/low discharge
pressure
3. Have authorized service representative repair unit
4. Replace
5. Replace
3. Replace or repair as necessary
!
Air leaking from
unloader on pressure
switch
Check valve stuck in an open position
DANGER
Do not disassemble check valve
with air in tank; bleed tank
Remove and replace check valve
!
DANGER
Do not disassemble check valve
with air in tank; bleed tank
18 Sp
7
WL Series
Serie WL
Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty - One Year, Serious Duty - Two Years, Extreme
Duty - Three Years.
2. WHO GIVES THIS WARRANTY (WARRANTOR):
Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld
compressor.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld air compressor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects due to material and workmanship with the exceptions noted below.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF
ORIGINAL PURCHASE AS STATED IN THE DURATION. If this compressor is used for commercial, industrial or rental purposes, the
warranty will apply for ninety (90) days from the date of purchase. Four cylinder single-stage and two-stage compressors are not
limited to a ninety (90) day warranty when used in commercial or industrial applications. Some States do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR
MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions
provided in the owner’s manual(s) supplied with compressor.
D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
E. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.
F. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply
with the warranty given by the engine manufacturer which is supplied with the product.
G. Additional items not covered under this warranty:
1. All Compressors
a. Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in accordance
with installation and operation guidelines or damaged by contact with tools or surroundings.
b. Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants.
c. Cosmetic defects that do not interfere with compressor functionality.
d. Rusted tanks, including but not limited to rust due to improper drainage or corrosive environments.
e. Electric motors, check valves and pressure switches after the first year of ownership.
f. Drain cocks.
g. Damage due to incorrect voltage or improper wiring.
h. Other items not listed but considered general wear parts.
i. Pressure switches, air governors and safety valves modified from factory settings.
2. Lubricated Compressors
a. Pump wear or valve damage caused by using oil not specified.
b. Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance guidelines.
3. Belt Drive / Direct Drive / Gas Driven Compressors
a. Belts.
b. Ring wear or valve damage from inadequate filter maintenance.
c. Manually adjusted load/unload and throttle control devices.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, compressor or component which is
defective, has malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Portable compressors or components must be delivered or shipped to the nearest Campbell Hausfeld Authorized Service Center.
Freight costs, if any, must be borne by the purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:
A. Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on
the availability of replacement parts.
B. If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact Campbell
Hausfeld (see paragraph 2).
Limited Warranty applies in the U.S. and Canada only and gives you specific legal rights. You may also have other rights which vary from
State to State or country to country.
TM
BUILT TO LAST
8
¡NO DEVUELVA EL
PRODUCTO AL
MINORISTA!
!
PELIGRO
!
PRECAUCION
AVISO
______________________
ADVERTENCIA
Para Desempacar
© 2000 Campbell Hausfeld
www.chpower.com
ALTO!
Compresores
Sin Aceite
!
ADVERTENCIA
!
PELIGRO
MANUAL
Series WL
TM
BUILT TO LAST
ARRÊT!
!
DANGER
AVERTISSEMENT
ATTENTION
AVIS
____________________
Date d’Achat
____________________
AVERTISSEMENT
!
DANGER
© 2000 Campbell Hausfeld
16 Fr
Series WL
MANUEL
!
AVERTISSEMENT
!
ATTENTION
AVERTISSEMENT
!
DANGER
AVIS
Guide De Dépannage (Suite)
Symptôme
DANGER
PRÉCAUTIONS DE PULVÉRISATION
!
AVERTISSEMENT
10 Fr
Figure 1
Pied en
caoutchouc
!
AVERTISSEMENT
DANGER
!
15 Fr
DANGER
Series WL
Guide De Dépannage
Assemblage (Suite)
Symptôme
DANGER
*
!
DANGER
TEST
RESET
ATTENTION
DANGER
DANGER
!
!
14 Fr
ATTENTION
AVERTISSEMENT
ATTENTION
!
DANGER
DANGER
!
AVERTISSEMENT
11 Fr
ATTENTION
ATTENTION
UT
A
AVERTISSEMENT
O / OF
!
PROTECTEUR DE SURCHARGE
THERMIQUE
(Suite)
Manostat
!
AVERTISSEMENT
!
AVERTISSEMENT
AVERTISSEMENT
ATTENTION
Figure 8
12 Fr
Figure 5 - Manostat
ATTENTION
GRAISSAGE
F
Figure 6
13 Fr
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed