null null

Liquid Crystal Projector
LCOS Technology
Model
28A9115
User's Manual
Liquid Crystal Projector
Model 28A9115
USER'S MANUAL
ENGLISH
00CP-SX5500W02 01.10.23 8:18 PM ページ 2
FRANÇAIS
Please read this user's manual thoroughly to ensure correct usage through understanding.
01CP-SX5500W02 01.10.24 1:41 PM ページ 1
Liquid Crystal Projector
ENGLISH
USER'S MANUAL
Thank you for purchasing this liquid crystal projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of
International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of
Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard
Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the
trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
Page
Page
FEATURES .......................................2
BEFORE USE ...................................2
TROUBLESHOOTING ....................20
Contents of Package ..............................2
Part Names.............................................3
Loading the Batteries..............................5
INSTALLATION ................................6
Installation of the Projector and Screen........6
Angle Adjustment ...................................6
Cabling ...................................................7
Power Connection ..................................8
Example of System Setup ......................8
Plug & Play .............................................8
OPERATIONS ...................................9
Power On ...................................................9
Power Off ................................................9
Basic Operation ....................................10
Setup Menu ..........................................12
Input Menu............................................13
Image Menu..........................................14
Options Menu .......................................15
No Signal Menu ....................................16
MAINTENANCE ..............................17
Lamp.....................................................17
Air Filter ................................................19
Other Maintenance ...............................19
OSD Message ......................................20
Indicators Message ..............................21
Symptom ..............................................22
SPECIFICATIONS...........................23
WARRANTY AND AFTER-SERVICE ......24
.......................................................................................
TABLES
Table 1. Installation Reference.................6
Table 2. Cabling .......................................7
Table 3. Basic Operations ......................10
Table 4. Setup Menu ..............................12
Table 5. Input Menu................................13
Table 6. Image Menu..............................14
Table 7. Options Menu ...........................15
Table 8. No Signal Menu ........................16
Table 9. OSD Message ..........................20
Table 10. Indicator Message ..................21
Table 11. Symptom ................................22
Table 12. Specifications .........................23
.......................................................................................
For "TECHNICAL" and "REGULATORY
NOTICE", see the end of this manual.
ENGLISH-1
01CP-SX5500W02 01.10.24 1:41 PM ページ 2
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space is required for installation and large images can
easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
Extra-low Noise Function
Acoustic noise level from the unit can be reduced.
BEFORE USE
Contents of package
Make sure all of the following items are included in the package. If anything is missing, please
contact your dealer.
NOTE • Keep the original packing material for future reshipment.
Power Cord
(US Type)
Power Cord
(UK Type)
Power Cord
(Europe Type)
USER'S MANUAL
BEDIENUNGSANLEITUNG
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung
aufmerksam.
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter
comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el
producto.
GEBRUIKSAANWIJZNG
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te
hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
ITALIANO FRANÇAIS DEUTSCH
CP-SX5500W
Please read this user's manual thoroughly to ensure correct usage through understanding.
NEDERLANDS ESPAÑOL
Liquid Crystal Projector
ENGLISH
Projector
REGULATORY NOTICES
TECHNICAL PORTGÊS
TECHNICAL
NORSK
INSTRUÇÕES DO PROPRIETÁRIO
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do
usuário.
User’s Manual
(this manual)
RGB Cable
Video/Audio Cable
(with white lead)
Component
Video Cable
(with green lead)
BLANK
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
KEYSTONE
MENU SELECT
Safety Instructions
Batteries
for Remote Control
Transmitter
RESET
POSITION
FREEZE
MAGNIFY
PinP
MUTE
OFF
VOLUME
Remote Control
Transmitter
ENGLISH-2
01CP-SX5500W02 01.10.24 1:41 PM ページ 3
BEFORE USE (continued)
ENGLISH
Part Names
KEYSTONE
TEMP Indicator
LAMP
KEYSTONE
Button
TEMP
LAMP Indicator
1
2
3
INPUT SELECT
STANDBY/ON Button
( STANDBY/ON Indicator)
VIDEO
MENU Button
RGB
RESET
MENU
STANDBY / ON
RESET Button
VIDEO Button
Control Panel
(Refer to P.9 "OPERATIONS")
RGB Button
Control Panel
Remote Control Sensor
Ventilation Openings
(exhaust)
Lens
AC Inlet
(to Power Cord)
Carrying Handle
Air Filter and Intake
for the Cooling Fan
Power Switch
Lens Cap
Foot Adjuster
Front/Right View
Remote Control Sensor
Terminal Panel
(Refer below)
Speaker
Rear/Left View
COMPONENT VIDEO
Y Terminal
CB/PB Terminal
CR/PR Terminal
DVI Terminal
3
CB/PB
Y
AUDIO OUT Terminal
RGB AUDIO IN
RGB 1/DVI Terminal
RGB 2 Terminal
RGB IN 1 Terminal
RGB IN 2 Terminal
RGB IN
VIDEO IN
COMPONENT VIDEO
CR/PR
3 2
1
2
S-VIDEO
VIDEO Terminal
VIDEO AUDIO IN
R Terminal
L/MONO Terminal
DVl
1
R
RGB OUT
VIDEO AUDIO IN
RGB1/DVl
AUDIO OUT
CONTROL
RGB OUT Terminal
CONTROL Terminal
VIDEO
RGB2
RGBAUDIO IN
USB
Terminal Panel
S-VIDEO Terminal
USB Terminal
ENGLISH-3
01CP-SX5500W02 01.10.24 1:41 PM ページ 4
BEFORE USE (continued)
Part Names (continued)
BLANK Button
STANDBY/ON Button
VIDEO Button
B
STAN
DBY/O
N
LAS
K
LAN
LASER Button
ER
RGB Button
B
RG
Disk Pad
MOUSE / RIGHT Button
O
VIDE
Used to operate the
mouse shift function and
left click function.
Used to click the right
mouse button.
KEYSTONE Button
AUTO Button
MENU Button
O
AUT
MENU SELECT Button
Used to click the left
mouse button.
,
,
,
Button
Used to operate the
mouse shift function.
M
RESET Button
TONE
KEYS
ENU
ME
NU
ION
POSIT
SEL
Used to click the right
mouse button.
ECT
T
E
RES
EZE
FRE
FREEZE Button
PinP
TE
MU
NIFY
MAG
PinP Button
MUTE Button
OFF
E
OLUM
V
VOLUME Button
POSITION Button
MAGNIFY Button
REMOTE CONTROL TRANSMITTER
(Refer to P.9 "OPERATIONS")
These functions works when the mouse control function is activated. Remember, the POSITION,
BLANK ON and MENU ON functions disable the mouse control function.
WARNING • The laser pointer of the remote control transmitter is used in
place of a finger or rod. Never look directly into the laser beam outlet or point
the laser beam at other people. The laser beam can cause vision problems.
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM
WAVE LENGTH: 650nm
MAX . OUTPUT: 1mW
CLASS 2 LASER PRODUCT
RADIAZIONI LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE 2
RAYONNEMENT LASER
MANUFACTURED
NE PAS REGARDER DANS
LE FAISCEAU APPAREIL
A LASER DE CLASSE 2
LASER-STRAHLUNG
PLACE OF
MANUFACTURER:A
NICHT IN DEN STRAHL
MADE IN JAPAN
BLICKEN LASER KLASSE2
IEC60825-1:1993+A1:1997
NOTE To prevent any malfunction;
• Do not give the remote control transmitter any physical impact. Take care not to drop.
• Do not place the heavy objects on the remote control transmitter.
• Do not wet the remote control transmitter or place it on any wet object.
• Do not place the remote control transmitter close to the cooling fan of the projector.
• Do not disassemble the remote control transmitter in case of malfunction. Please bring it to the
service station.
ENGLISH-4
01CP-SX5500W02 01.10.24 1:41 PM ページ 5
BEFORE USE (continued)
Install the AA batteries into the remote control
transmitter.
1. Remove the battery cover.
Push the knob while lifting up the battery cover.
2. Load the batteries.
Make sure the plus and minus poles are correctly
oriented.
3. Close the battery cover.
ENGLISH
Loading the Batteries
1
2
CAUTION • Use only the specified batteries with this remote control
transmitter. Also, do not mix new and old batteries. This could cause in
battery cracking or leakage, which could result in fire or personal injury.
• When loading the batteries, make sure the plus and minus terminals are
correctly oriented as indicated in the remote control transmitter. Incorrect
orientation could cause battery cracking or leakage, which could result in
personal injury or pollution of the surrounding environment.
• When you dispose the battery, you should obey the law in the relative area or
country.
• Keep the battery away from children and pets.
• When not to be used for an extended period, remove the batteries from the
remote control transmitter.
NOTE Replace the batteries when remote control transmitter operation becomes difficult.
ENGLISH-5
01CP-SX5500W02 01.10.24 1:41 PM ページ 6
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining of the screen size and projection distance.
The projection distances shown in the table below
are for full size (1365 x 1024 dots).
a: Distance from the projector to the screen. (±10%)
Screen
Table 1. Installation Reference
Screen size
[inches (m)]
a [inches (m)]
Min.
Max.
40 (1.0)
60 (1.5)
65 (1.6)
98 (2.5)
85 (2.2)
127 (3.2)
80 (2.0)
131 (3.3)
170 (4.3)
100 (2.5)
164 (4.2)
213 (5.4)
120 (3.0)
196 (5.0)
255 (6.5)
150 (3.8)
246 (6.2)
319 (8.1)
200 (5.0)
328 (8.3)
426 (10.8)
Top View
a
Side View
CAUTION • Install the projector in a suitable environment according to
instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this
manual.
• When you fix this unit with a metal tool and the like, you must connect it with
ground wire; otherwise, fire or electric shock can result.
Connect the ground terminal of AC inlet of this unit with the ground terminal
provided at the building using an optional three-core power-supply cord.
• Please basically use liquid crystal projector at the horizontal position. If you use
liquid crystal projector by the lens up position, the lens down position and the side up
position, this may cause the heat inside to build up and become the cause of damage.
Be especially careful not to install it with ventilation holes blocked.
• Do not install LCD projector in smoke effected environment. Smoke residue may
buildup on critical parts (i.e.LCD panel, Lens Assy etc.).
Angle Adjustment
Use the foot adjusters on the bottom of the
projector to adjust the projection angle. It is
variable within 0˚ to 8˚ approximately.
1. Lift up the front side of the projector, and
pressing the foot adjuster button, adjust the
projection angle.
2. Release the button to lock at the desired angle.
3. Use the foot adjusters for fine adjustment, Do
not force the foot adjuster screws. This could
damage the adjusters or cause the lock to fail.
Foot Adjusters
Variable within the range of approximately 0° - 8°
CAUTION • Do not release the foot adjuster button unless the projector is
being held; otherwise, the projector could overturn or the fingers could get
caught and cause personal injury.
ENGLISH-6
01CP-SX5500W02 01.10.24 1:41 PM ページ 7
INSTALLATION (continued)
ENGLISH
Cabling
Refer to the table below for connecting each terminal of the projector to each device.
Table 2. Cabling
Function
Analog RGB input
Terminal
RGB IN 1
RGB IN 2
Analog RGB output
RGB OUT
DVI input
DVI
Audio input
(from the computer)
Cable
Accessory RGB cable or optional RGB
cable with D-sub 15-pin shrink jack and
inch thread screws
Optional DVI cable with inch thread screws
RGB AUDIO IN [RGB 1 / DVI]
(interlocked with RGB IN 1 or DVI)
Optional audio cable with stereo mini jack
RGB AUDIO IN [RGB 2]
(interlocked with RGB IN 2)
Accessory PS/2 mouse cable
Serial mouse control
Optional Serial mouse cable
RS-232C communication
Optional RS-232C cable
USB
Optional USB cable
S-video input
S-VIDEO
Optional S-video cable with mini DIN 4-pin
jack
Video input
VIDEO
Accessory video/audio cable
COMPONENT VIDEO [Y]
Component video input
COMPONENT VIDEO [CB/PB]
Accessory component video cable
COMPONENT VIDEO [CR/PR]
Audio input
(from video equipment)
AUDIO [L / MONO]
AUDIO [R]
Accessory video/audio cable or optional
audio cable with RCA jack
Audio output
AUDIO OUT
Optional audio cable with stereo mini jack
CAUTION • Incorrect connecting could result in fire or electrical shock.
Please read this manual and the separate “SAFETY INSTRUCTIONS”.
• Before connecting, turn off to all devices to be connected, except for the USB
cable.
• The cables may have to be used with the core set to the projector side. Use the
cables which are included with the projector or specified.
NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the
projector is compatible with the device.
• Secure the screws on the connectors and tighten.
• For some RGB input modes, the optional Mac adapter is necessary.
• To select the DVI input, the computer may need some settings. See the manuals of the computer for details.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.
• Refer to the “TECNICAL” section for the pin assignment of connectors and RS-232C communication data.
• When the DVI terminal is used, the RGB OUT terminal may not function.
ENGLISH-7
01CP-SX5500W02 01.10.24 1:41 PM ページ 8
INSTALLATION (continued)
Power Connection
Use the correct one of the enclosed power cords depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION • Be carful in handling the power
cord according to instructions of the
accompanying manual "SAFETY INSTRUCTIONS"
and this manual.
• Connect the power cord firmly. Avoid using a
loose, unsound outlet or contact failure.
Power
outlet
Power Cord
AC Inlet
Example of system setup
Computer
(desktop type)
DVD Player
3 DVl
RGB IN
VIDEO IN
COMPONENT VIDEO
CR/PR
CB/PB
Y
3 2
1
2
S-VIDEO
1
R
RGB OUT
CONTROL
Computer
(notebook type)
VIDEO
VIDEO AUDIO IN
RGB1/DVl
S-Video Tape
Recorder
Speaker with
amplifier
AUDIO OUT
RGB2
RGBAUDIO IN
USB
Computer
(desktop type)
Display Monitor
NOTE • When connecting with notebook computer, set to valid the RGB external image output
(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of
the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer
that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the accessory RGB cable with RGB IN 1 terminal (DDC
1/2B compatible), or by connecting an optional DVI cable with DVI terminal (DDC 2B
compatible). Plug & play may not operate by other connecting.
NOTE • Plug & play is a system configured with peripheral equipment including a computer and
display, and an operating system.
• This projector is recognized as a plug & play monitor. Use the standard display drivers.
• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug &
play does not operate correctly.
ENGLISH-8
01CP-SX5500W02 01.10.24 1:41 PM ページ 9
STANDBY/ON Button
(STANDBY/ON Indicator)
STANDBY/
ON Button
BLANK
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
Power Switch
KEYSTONE
MENU SELECT
RESET
POSITION
Zoom Knob
FREEZE
MAGNIFY
Focus Ring
PinP
MUTE
OFF
VOLUME
Power ON
1. Check that the power cord is connected correctly.
2. Set the power switch to [ | ]. The standby mode is selected, and the STANDBY/ON indicator is
turned to orange.
3. Press the STANDBY/ON button
on the control panel or the remote control transmitter.
Warm-up begins and the STANDBY/ON indicator blinks in green.
4. The STANDBY/ON indicator ceases blinking and turns to green when power is on. Remove the
lens cap.
5. Adjust picture size using the Zoom Knob.
6. Adjust focus using the Focus Ring .
Power OFF
1. Press the STANDBY/ON button
on the control panel or the remote controller. Then,the
message "Power off?" will appear on the screen, and the message will disappear by any operation
or no operation for 5 seconds. During this message indication, press the STANDBY/ON
button again. The projector lamp is extinguished and lamp cooling begins. The STANDBY/ON
indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button
has no
effect while the STANDBY/ON indicator is blinking.
2. The system assumes the Standby mode when cooling is complete, and the STANDBY/ON
indicator ceases blinking and changes to orange. Check that the indicator is orange and set the
Power switch to [O].
3. The STANDBY/ON indicator is extinguished when power is off. Attach the lens cap.
Put the Lens cap to the lens properly. In order to do it, keep pushing two knobs on the lens cap,
then fit it to the lens holding the cap in horizontal position.
WARNING • Please read this manual, and the separate “SAFETY
INSTRUCTIONS” thoroughly before using the equipment. Always ensure that
the equipment is used safely.
NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off.
Incorrect procedure will reduce the life of the projector lamp and LCD panel.
• To prevent any troble, turn on/off the projector when the computer or video tape recorder is OFF.
Providing a RS-232C cable is connected, turn on the computer before the projector.
ENGLISH-9
ENGLISH
OPERATIONS
01CP-SX5500W02 01.10.26 6:36 PM ページ 10
OPERATIONS (continued)
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item
Description
Select RGB Input : Press the RGB button.
VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DVI
RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)
INPUT
Select Video Input : Press the VIDEO button.
SELECT (*) RGB IN 1/RGB IN 2/DVI → VIDEO/S-VIDEO/COMPONENT VIDEO
VIDEO → S-VIDEO → COMPONENT VIDEO (→ VIDEO)
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
Set/Clear Position Adjustment Mode : Press the POSITION button.
The [
] icon is displayed in the POSITION mode.
POSITION
Image Position Adjustment: Press the
POSITION mode.
,
,
and
buttons in the
RESET (*)
Initialise Each Item : Select an item and press the RESET button.
Initialise Position Adjustment : Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
buttons may operate as the mouse control button. Refer to page 4.
•
, ,
and
• Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY
button.
Move Magnified Area : Run the POSITION in the MAGNIFY mode.
Adjust Magnification : Press the MAGNIFY
/
button in MAGNIFY
mode.
Clear MAGNIFY Mode : Press the MAGNIFY
button.
OFF
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is
displayed, and the image frozen, in the FREEZE mode.
FREEZE
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, KEYSTONE, or by
changing the input signal.
• Do not forget to clear frozen static images.
NOTE • Use the remote control transmitter at a distance of approximately 5m from the sensor on
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will
interfere with operation of the remote control transmitter.
ENGLISH-10
01CP-SX5500W02 01.10.24 1:41 PM ページ 11
OPERATIONS (continued)
ENGLISH
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item
VOLUME
Volume Adjustment : Press the VOLUME
MUTE
Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
/
button.
Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input : Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals.
BLANK
ON/OFF
MENU
ON/OFF
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
Menu Display Start/Stop: Press the MENU button.
• The menu display is terminated automatically after approximately 10 seconds of
inactivity.
Select Menu Type: Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the
and
buttons as with the normal menu.
MENU
SELECT
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu
Single menu
(MENU SELECT)
SETUP
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
P.IN P.
MODE
IMAGE
OPT.
0
-2
100
100
+1
800
0
0
CONTRAST
-2
Select Mode of P.IN P. Display : Press the PinP button.
Small → Large → P.IN P. off ( → Small)
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
Set / Clear KEYSTONE Mode : Press the KEYSTONE
button.
/
button in the KEYSTONE
KEYSTONE Select KEYSTONE Mode : Press the
↔
Horizontal
mode. Vertical
Adjust KEYSTONE : Press the
/
button.
ENGLISH-11
01CP-SX5500W02 01.10.24 1:42 PM ページ 12
OPERATIONS (continued)
Setup Menu
SETUP
The following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the
and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
Item
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
OPT.
SETUP
0
-2
INPUT
IMAGE
OPT.
0
+1
+1
0
0
0
0
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE
COLOR BAL R
COLOR BAL B
ASPECT
100
100
+1
800
0
0
VIDEO
S-VIDEO
COMPONENT VIDEO
RGB IN 1
RGB IN 2
DIGITAL
RGB IN 1
DIGTAL
RGB IN 2
VIDEO
S-VIDEO
COMPONENT
✔
✔
✔
↔ Strong
✔
✔
✔
↔ Up
✔
-
-
↔ Right
✔
-
-
Adjustment: Left
↔ Right
• Adjust to eliminate flicker.
✔
-
✔
↔ Large
• The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.
✔
-
-
↔ Clear
-
-
✔
↔ Dark
-
-
✔
-
-
✔
BRIGHT
Adjustment: Dark
CONTRAST
Adjustment: Weak
V POSIT
Adjustment: Down
H POSIT
Adjustment: Left
H PHASE
↔ Light
Adjustment: Small
H SIZE
SHARPNESS Adjustment: Soft
COLOR
TINT
Adjustment: Light
↔ Green
• Valid only when NTSC or NTSC 4.43 signal is received.
Adjustment: Red
COLOR BAL R Adjustment: Light
↔ Dark
✔
✔
✔
COLOR BAL B Adjustment: Light
↔ Dark
✔
✔
✔
✔
✔
-
-
-
✔
Select Image Aspect Ratio :
Full [
]
↔
16:9[
]
↔
Real [
]
Select Position of Image:
Press the
button while 16:9[
] is selected.
Center →
Down →
Up ( → Center
)
ASPECT
Select Image Aspect Ratio:
4:3[
]
↔
16:9[
]
↔
4:3 small[
Select Position of Image :
Press the
button while 16:9[
] / 4:3 small[
is selected.
Center →
Down →
Up ( → Center
)
]
]
• 4:3 small may not be displayed correctly with some input
signals.
ENGLISH-12
01CP-SX5500W02 01.10.24 1:44 PM ページ 13
Input Menu
The following functions are available when INPUT is selected on the
menu. Select an item with the
and
buttons, and start or stop
operation with the
and
buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
SETUP
INPUT
AUTO
RGB
VIDEO
Progressive
BLACK
HDTV
IMAGE
OPT.
EXECUTE
CANCEL
Table 5. Input Menu
Item
AUTO
Description
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button. Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTE with the
button. A signal type appropriate for the input signal is selected
automatically when EXECUTE is selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency: Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
Select Video Signal Type: Select the signal type with the
and
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
VIDEO (**)
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal type
is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF
with the
/
button. When the TURN ON is selected, the black
BLACK (**)
enhancement mode is active and the contrast ratio of the screen for the
video input will be raised by making black level darker.
Select Progressive Mode: Select the mode suitable for the input signal
with the
and
buttons. The TV mode and the FILM mode convert the
Progressive interlaced video signal into the progressive signal. The FILM mode is
(**)
adptable 2-3 Pull-Down system to the conversion.
• Use this function to raise resolution, at the interlaced video input except HDTV
signal.
HDTV
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the
input signal with the
/
button.
ENGLISH-13
ENGLISH
OPERATIONS (continued)
01CP-SX5500W02 01.10.24 1:44 PM ページ 14
OPERATIONS (continued)
Image Menu
SETUP
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the
and
buttons, and
start or stop operation with the
and
buttons.
BLANK
MIRROR
START UP
P. IN P.POSIT
P.IN P.INPUT
GAMMA
INPUT
IMAGE
OPT.
Table 6. Image Menu
Item
Description
Select Blank Screen Color: Select color with the
and
buttons.
BLANK
• The image is cleared and the entire screen is displayed in the selected color, when
BLANK mode is set with BLANK ON, or when there is no signal for 5 minutes.
MIRROR
Select Mirror Status: Select mirror status with
START UP
Setup Initial Screen Display: Select TURN ON with the
Clear Initial Screen Display: Select TURN OFF with the
P. IN P.
POSIT
P. IN P.
INPUT
GAMMA
ENGLISH-14
and
buttons.
button.
button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when there
is no signal.
Select Position of P. in P. Display : Press the
or
button.
↔
↔
↔
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
Select signal of P. in P. Display : Press the
or
button.
↔
S-VIDEO
↔
COMPONENT
VIDEO
Select Gamma mode: Select the gamma mode with the
/
↔
CINEMA
↔
DYNAMIC
NORMAL
button.
01CP-SX5500W02 01.10.24 1:44 PM ページ 15
SETUP
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the
and
buttons, and
start or stop operation with the
and
buttons. The function
indicated (**) are effective on video input mode only, not on RGB input
mode, except in the P.IN P. window on RGB input mode.
INPUT
IMAGE
OPT.
16
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
Description
↔ Increase VOLUME
VOLUME
Volume Adjustment: Reduce VOLUME
MENU COLOR
Select Menu Background Color: Select with the
and
buttons.
Select Menu Display Language: Select with the
and
buttons.
AUTO OFF
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select STOP (0 min.) with the
button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G Valid: Select TURN ON with the
button.
SYNC ON G Invalid: Select TURN OFF with the
button.
SYNC ON G
WHISPER
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
Set / Crear WHISPER Mode: Press the
and
button.When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic moise level from the unit is reduced, and brightness
level on screen is a little lower.
ENGLISH-15
ENGLISH
OPERATIONS (continued)
01CP-SX5500W02 01.10.24 1:39 PM ページ 16
OPERATIONS (continued)
No Signal Menu
The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.
Table 8. No Signal Menu
Item
VOLUME
BLANK
MIRROR
START UP
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
16
↔ Increase VOLUME
• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME
or VOLUME
button.
Volume Adjustment: Reduce VOLUME
VOLUME
Select Blank Screen Color: Select the color with the
BLANK
MIRROR
START UP
and
buttons.
• The image is cleared and the entire screen is displayed in the selected color,
when BLANK mode is set with BLANK ON, or when there is no signal for 5
minutes.
Operation Start/Stop: Press the
or
button.
Select Mirror Status: Select the mirror status with the
buttons.
and
Operation Start/Stop: Press the
or
button.
Setup Initial Screen Display: Select the TURN ON with the
Clear Initial Screen Display: Select the TURN OFF with the
button.
button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
MENU COLOR
Select Menu Background Color: Select the color with the
buttons.
Operation Start/Stop: Press the
or
button.
Select Menu Display Language: Select the language with the
buttons.
AUTO OFF
SYNC ON G
WHISPER
ENGLISH-16
and
and
Operation start/stop: Press the
or
button.
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select the STOP (0 min.) with the
button. When
the STOP is selected the system does not enter the standby mode even
if no signal is received.
Operation Start/Stop: Press the
or
button.
SYNC ON G Valid: Select the TURN ON with the
button.
SYNC ON G Invalid: Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.
Operation Start/Stop: Press the
or
button.
Set / Crear WHISPER Mode: Press the
and
button.When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic moise level from the unit is reduced, and brightness
level on screen is a little lower.
01CP-SX5500W02 01.10.24 1:39 PM ページ 17
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Optional Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
WARNING • For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• Premature lamp failure MAY be caused by an
electronic component in the projector and not
necessarily the lamp. If unsure contact your local
service center.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
Lamp
Reflector
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time.
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.
ENGLISH-17
ENGLISH
MAINTENANCE
01CP-SX5500W02 01.10.24 1:39 PM ページ 18
MAINTENANCE (continued)
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove
the lamp cover.
5. Loosen the two screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the
unit.
7. Replace the lamp cover in position and tighten the screw
firmly.
8. Gently turn the projector right-side up.
CAUTION • Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 ■ CANCEL’ message will
then appear.
3. Press the
and select 0, and wait until the timer display is cleared.
NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate properly if the lamp timer is not
reset correctly.
• An air filter is attached to the optional lamp. Replace the filter after replacing the lamp.
ENGLISH-18
01CP-SX5500W02 01.10.24 1:39 PM ページ 19
Air Filter
CP-SX5500
Replacing the Air Filter
Replace the air filter if contamination cannot be
removed, or if it is damaged.
ENGLISH
MAINTENANCE (continued)
Filter box
1. Remove the filter lid.
2. Pull and remove the old filter from the filter box.
3. Insert the new filter to the filter box. Push left
and right edges of the filter with fingers in order
to fit the filter to the box properly. Check that
there is no gap between the filter and plastics at
top, left and right side edge of the filter.
4. Set the filter lid.
Filter Lid
Filter
Cleaning the air Filter
The air filter should be cleaned as described below at intervals of approximately 300 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item “Option
Parts” of the Table 12.
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
ENGLISH-19
01CP-SX5500W02 01.10.24 1:39 PM ページ 20
TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such a message appears.
Contents
The message shown at left appears after the lamp has
been used for more than 1300 hours.
CHANGE THE LAMP
The lamp is approaching the end of its life.
AFTER REPLACING LAMP,
Power is switched OFF automatically when the lamp
RESET THE LAMP TIME.
*1) reaches the end of its life. Prepare a new lamp for
installation.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER ** hr.
*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
The lamp will reach the end of its life in ** hours.
Power will be switched OFF automatically in ** hours.
Replace the lamp as shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
The lamp has reached the end of its life. Power will be
switched OFF in a few minutes.
Switch power OFF immediately and replace the lamp as
shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
NO INPUT IS DETECTED
ON ***
No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
NOTE *1) This message is cleared automatically after approximately three minutes, and appears
every time power is switched ON.
ENGLISH-20
01CP-SX5500W02 01.10.24 1:39 PM ページ 21
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
STANDBY/ON LAMP
TEMP
indicator indicator indicator
Contents
Lights
orange
Turns off Turns off The Standby mode has been set.
Blinks
green
Turns off Turns off Warming up. Please wait.
Lights
green
Turns off Turns off ON. Normal operation possible.
Blinks
orange
Turns off Turns off Cooling. Please wait.
Lights red
Lights red
Lights
red
Lamp is not lit.
The interior of the equipment may be too hot. Switch
power OFF, wait 20 minutes until the equipment cools,
and check whether the ventilation openings are
Turns off
blocked, whether the air filter is dirty, or whether the
ambient temperature exceeds 35 °C. And switch power
ON again. Replace the lamp if the same problem
occurs.
Blinks
red
Lamp or lamp cover is not found, or hasn’t been fitted in
correctly.
Switch power OFF, and wait for 45 minutes until the
Turns off
equipment cools. Check fitting of the lamp and lamp
cover, and switch power ON again. Contact your dealer
if the same problem occurs again.
Lights red Turns off
Blinks
red
The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check for foreign matters in the fan,
and switch power ON again. Contact your dealer if the
same problem occurs again.
NOTE *1) When the internal temperature becomes excessive power is switched OFF
automatically for safety reasons, and the indicator is extinguished. Set the power switch to [O] and
wait for 20 minutes until the equipment has cooled sufficiently.
ENGLISH-21
ENGLISH
TROUBLESHOOTING (continued)
01CP-SX5500W02 01.10.24 1:39 PM ページ 22
TROUBLESHOOTING (continued)
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
Symptom
The power is not
turned on.
Remedy
The main power switch is not
turned on.
Turn on the main power switch.
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The input is not correctly set.
Use the projector or remote control
transmitter to set.
10
No signal input.
Connect correctly.
7,8
The projector is not correctly
connected.
Connect correctly.
7,8
No video or audio.
Video is present but
The volume is set to minimum.
no audio.
Press VOLUME
on the remote
control or display the menu screen
and adjust the volume.
Mute is turned on.
Press the MUTE
The projector is not correctly
connected.
Connect correctly.
button.
Audio is present but The brightness adjustment knob Select BRIGHT with the MENU
button and the press the
button.
is rotated fully clockwise.
no video.
The lens cap is still attached.
Colors are pale and Color density and color
color matching is
matching are not correctly
poor.
adjusted.
Images are dark.
Video is blurred.
ENGLISH-22
Page
Remove the lens cap.
8,9
11,15
11
7,8
12
9
Adjust the video.
12
Brightness and contrast are not
Adjust the video.
correctly adjusted.
12
The lamp is nearing the end of
its service life.
Replace with a new lamp.
17
WHISPER mode is set.
Clear WHISPER mode.
15
Focus or H PHASE is out of
adjustment.
Adjust the focus or H PHASE.
9,12
01CP-SX5500W02 01.10.24 1:39 PM ページ 23
ENGLISH
SPECIFICATIONS
Table 12. Specifications
Item
Specification
Product name
Liquid
crystal
panel
Liquid crystal projector
Panel size
2.3 cm (0.9 type)
Drive system
TFT active matrix
1,397,760 pixels (1365 horizontal x 1024 vertical)
Lens
Zoom lens F=2.7 ~ 3.1 f=38.0 ~ 49.0 mm
Lamp
220 W UHB
Speaker
1W
Power supply
AC100 ~ 120V, 4.0A / AC220 ~ 240V, 1.8A
Power consumption
360W
Temperature range
0 ~ 35°C (Operating)
Size
250 (W) x 103 (H) x 335 (D) mm
Weight (mass)
5.6 kg
1
RGB IN
RGB
signal
input
2
Video
signal
input
TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p
TTL Level (Positive/Negative)
DVI
AUDIO IN
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
RGB1
DVI
RGB2
200mVrms, 20 kΩ (max. 3.0Vp-p)
Stereo mini jack
VIDEO
1.0Vp-p, 75Ω terminator
RCA jack
S-VIDEO
Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.286Vp-p (burst signal), 75Ω terminator
Mini DIN 4-pin jack
Y
1.0 Vp-p, 75 Ω Terminator (Positive)
COMPONENT
CB/CR 0.7 Vp-p, 75 Ω Terminator (Positive)
VIDEO
PB/PR 0.7 Vp-p, 75 Ω Terminator (Positive)
AUDIO
Signal
output
Control
functions
L
R
200mVrms, 20 kΩ (max. 3.0Vp-p)
RCA jack
RGB OUT
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
AUDIO OUT
200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)
Stereo mini jack
CONTROL
D-sub 15-pin shrink plug
USB
USB jack (B type)
Optional Parts
Lamp: DT00421
Air Filter: MN04291
* For others, consult your dealer.
NOTE • This specifications are subject to change without notice.
ENGLISH-23
01CP-SX5500W02 01.10.24 1:39 PM ページ 24
WARRANTY AND AFTER-SERVICE
If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and
run through the suggested checks. If this does not resolve the problem contact your dealer or service
company. They will tell you what warranty condition is applied.
ENGLISH-24
03CP-SX5500W02 01.10.24 1:19 PM ページ 1
INDEX
Page
Page
DÉPANNAGE..................................20
CARACTÉRISTIQUES TECHNIQUES ....23
GARANTIE ET SERVICE APRÈS-VENTE ..24
.......................................................................................
FRANÇAIS - 1
FRANÇAIS
03CP-SX5500W02 01.10.24 1:19 PM ページ 2
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter
comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el
producto.
GEBRUIKSAANWIJZNG
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te
hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
ITALIANO FRANÇAIS DEUTSCH
Please read this user's manual thoroughly to ensure correct usage through understanding.
BEDIENUNGSANLEITUNG
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung
aufmerksam.
NEDERLANDS ESPAÑOL
USER'S MANUAL
ENGLISH
TECHNICAL
REGULATORY NOTICES
Câble RVB
TECHNICAL PORTGÊS
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do
usuário.
NORSK
INSTRUÇÕES DO PROPRIETÁRIO
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
KEYSTONE
MENU SELECT
RESET
POSITION
FREEZE
MAGNIFY
PinP
MUTE
OFF
VOLUME
FRANÇAIS - 2
03CP-SX5500W02 01.10.24 1:19 PM ページ 3
Touche KEYSTONE
LAMP
TEMP
1
2
3
INPUT SELECT
Touche STANDBY/ON
(Témoin STANDBY/ON)
VIDEO
Touche MENU
RGB
RESET
MENU
Touche RESET
STANDBY / ON
Touche VIDEO
Touche RGB
Prise DVI
3
RGB AUDIO IN
Prise RGB1/DVI
Prise RGB2
RGB IN
VIDEO IN
COMPONENT VIDEO
CR/PR
CB/PB
Y
3 2
1
2
S-VIDEO
Prise VIDEO
VIDEO AUDIO IN
Prise R
Prise L/MONO
Prise AUDIO OUT
DVl
1
R
RGB OUT
CONTROL
Prise CONTROL
VIDEO
VIDEO AUDIO IN
RGB1/DVl
AUDIO OUT
Prise RGB IN 1
Prise RGB IN 2
Prise RGB OUT
RGB2
RGBAUDIO IN
USB
Prise S-VIDEO
Prise USB
FRANÇAIS - 3
FRANÇAIS
03CP-SX5500W02 01.10.24 1:19 PM ページ 4
BLA
STAN
DBY/O
N
LAS
NK
Touche LASER
ER
Touche RGB
GB
R
Touche SOURIS/DROITE
O
VIDE
Touche KEYSTONE
Touche AUTO
O
AUT
Touche MENU
Touche MENU SELECT
Dient zum Klicken der
linken Maustaste.
M
Touche RESET
TONE
KEYS
ENU
ME
NU
ION
POSIT
SEL
ECT
T
E
RES
Touche FREEZE
PinP
EZE
FRE
Touche PinP
TE
MU
Touche
,
,
,
NIFY
MAG
Touche MUTE
OFF
VOL
UME
Touche VOLUME
Touche POSITION
Touche MAGNIFY
FRANÇAIS - 4
03CP-SX5500W02 01.10.24 1:19 PM ページ 5
1
2
FRANÇAIS - 5
FRANÇAIS
03CP-SX5500W02 01.10.24 1:20 PM ページ 6
a [m]
Minimum
Maximum
1,6
2,5
3,3
4,2
5,0
6,2
8,3
2,2
3,2
4,3
5,4
6,5
8,1
10,8
a
FRANÇAIS - 6
03CP-SX5500W02 01.10.24 1:20 PM ページ 7
Prise
RGB IN 1
RGB IN 2
RGB OUT
DVI
RGB AUDIO IN [RGB 2]
(interverrouillage avec RGB IN 2)
Câble
Communication RS-232C
USB
S-VIDEO
VIDEO
COMPONENT VIDEO [CB/PB]
AUDIO [L/MONO]
AUDIO [R]
AUDIO OUT
FRANÇAIS - 7
FRANÇAIS
Fonction
03CP-SX5500W02 01.10.24 1:20 PM ページ 8
Cordon
d'alimentation
3 DVl
RGB IN
VIDEO IN
3 2
COMPONENT VIDEO
CR/PR
CB/PB
Y
1
2
S-VIDEO
1
R
RGB OUT
CONTROL
VIDEO
VIDEO AUDIO IN
RGB1/DVl
AUDIO OUT
RGB2
RGBAUDIO IN
USB
Ecran
d'affichage
FRANÇAIS - 8
03CP-SX5500W02 01.10.24 1:20 PM ページ 9
FONCTIONNEMENT
Touche STANDBY/ON
(Tèmoin STANDBY/ON)
Touche
STANDBY/ON
BLANK
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
KEYSTONE
RESET
POSITION
Bouton zoom
Bague focus
FREEZE
MAGNIFY
PinP
MUTE
OFF
VOLUME
FRANÇAIS - 9
FRANÇAIS
MENU SELECT
03CP-SX5500W02 01.10.26 6:38 PM ページ 10
INPUT
SELECT
(*)
VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DVI
RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)
RESET
(*)
FREEZE
FRANÇAIS - 10
03CP-SX5500W02 01.10.24 1:20 PM ページ 11
VOLUME
MUTE
AUTO
/
.
BLANK
ON/OFF
Menu normal
CONF.
ENTR.
LUMIN.
CONTRASTE
POSIT. V
POSIT. H
PHASE. H
TAIL. H
COUL BAL R
COUL BAL B
ASPECT
P.IN P.
MODE
IMAGE
OPT.
0
-2
100
100
+1
800
0
0
CONTRASTE
-2
FRANÇAIS - 11
FRANÇAIS
Postes
03CP-SX5500W02 01.10.24 1:20 PM ページ 12
CONF.
ENTR.
IMAGE
LUMIN.
CONTRASTE
POSIT. V
POSIT. H
PHASE. H
TAIL. H
COUL BAL R
COUL BAL B
ASPECT
OPT.
0
-2
100
100
+1
800
0
0
RGB IN 1
RGB IN 2
DIGITAL
CONF.
ENTR.
IMAGE
OPT.
0
+1
+1
0
0
0
0
LUMIN.
CONTRASTE
NETTETE
COULEUR
TEINTE
PHASE. H
COUL BAL R
COUL BAL B
ASPECT
VIDEO
S-VIDEO
COMPONENT VIDEO
Description
RGB IN 1
DIGTAL
RGB IN 2
VIDEO
S-VIDEO
COMPONENT
✔
✔
✔
↔ Puissant
✔
✔
✔
✔
-
-
✔
-
-
Réglage: Vers la gauche
✔
-
✔
TAIL. H
✔
-
-
NETTETE
-
-
✔
COULEUR
-
-
✔
-
-
✔
LUMIN.
POSIT. H
Réglage: Vers la gauche
PHASE. H
↔ Vers le haut
↔ Sombre
✔
✔
✔
↔ Sombre
✔
✔
✔
✔
✔
-
-
-
✔
FRANÇAIS - 12
03CP-SX5500W02 01.10.24 1:20 PM ページ 13
CONF.
ENTR.
AUTO
RGB
VIDEO
PROGRESSIF
NOIR
HDTV
IMAGE
OPT.
EX CUTION
ANNULER
Postes
AUTO
RGB
FRANÇAIS - 13
FRANÇAIS
03CP-SX5500W02 01.10.24 1:20 PM ページ 14
CONF.
ENTR.
IMAGE
OPT.
SUPPR.
MIROIR
DEMARRAGE
POSIT. P. IN P.
ENTR. P. IN P.
GAMMA
SUPPR.
POSIT.
P. IN P.
ENTR.
P. IN P.
GAMMA
et
FRANÇAIS - 14
.
03CP-SX5500W02 01.10.24 1:20 PM ページ 15
CONF.
ENTR.
IMAGE
OPT.
16
VOLUME
COUL MENU
LANGUE
AUTO OFF
SYNC ON G
SILENCIEUX
VOLUME
AUTO OF
.
SILENCIEUX
.
FRANÇAIS - 15
FRANÇAIS
Postes
03CP-SX5500W02 01.10.24 1:20 PM ページ 16
VOLUME
SUPPR.
MIROIR
DEMARRAGE
COUL MENU
LANGUE
AUTO OFF
SYNC ON G
SILENCIEUX
16
Tableau 8. Menu No Signal
Postes
VOLUME
SUPPR.
MIROIR
DEMARRAGE
AUTO OFF
SYNC ON G
SILENCIEUX
FRANÇAIS - 16
et
et
.
.
.
03CP-SX5500W02 01.10.24 1:20 PM ページ 17
ENTRETIEN
Lampe
Lampe
FRANÇAIS - 17
FRANÇAIS
HAUTE TENSION
TEMPÉRATURE ÉLEVÉE
HAUTE PRESSION
03CP-SX5500W02 01.10.24 1:20 PM ページ 18
FRANÇAIS - 18
03CP-SX5500W02 01.10.24 1:20 PM ページ 19
Filtre
FRANÇAIS - 19
FRANÇAIS
CP-SX5500
03CP-SX5500W02 01.10.24 1:20 PM ページ 20
REMPLACER LA LAMPE
REMETTRE LA MINUTERIE
À ZÉRO APRÉS AVOIR
REMPLACÉ L’AMPOULE.
*1)
REMPLACER LA LAMPE
REMETTRE LA MINUTERIE
À ZÉRO APRÉS AVOIR
REMPLACÉ L’AMPOULE.
COUPURE DU COURANT AU BOUT
DE ** HEURES.
*1)
REMPLACER LA LAMPE
REMETTRE LA MINUTERIE
À ZÉRO APRÈS AVOIR
REMPLACÉ L’AMPOULE.
COUPURE DU COURANT
AU BOUT
DE 0 HEURES.
ENTREE NON DETEC.
SUR ***
SYNC. HORS PLAGE
SUR ***
FRANÇAIS - 20
03CP-SX5500W02 01.10.24 1:20 PM ページ 21
Eteint
Eteint
Eteint
Eteint
Eteint
Eteint
Eteint
FRANÇAIS - 21
FRANÇAIS
03CP-SX5500W02 01.10.24 1:20 PM ページ 22
FRANÇAIS - 22
8,9
10
7,8
7,8
11,15
7,8
12
9
12
12
17
•Annulez le mode SILENCIEUX.
5
Page
.
11
9,12
03CP-SX5500W02 01.10.24 1:20 PM ページ 23
Nom de produit
2,3 cm (type 0,9)
Objectif
Xoom F=2,7 - 3,1 f=38,0 - 49,0 mm
Lampe
220 W UHB
1W
Alimentation
100 - 120 V CA, 4,0 A / 220 - 240 V CA, 1,8 A
360W
Dimensions
Poids (masse)
250 (L) x 103 (H) x 335 (P) mm
5,6 kg
1
2
RGB1
DVI
RGB2
VIDEO
1,0 Vc-c, terminaison 75 Ohms
S-VIDEO
Prise Cinch (RCA)
Y
1,0 Vc-c, 75 Ω terminaison 75 Ohms (positive)
COMPONENT
C
B/CR 0,7 Vc-c, 75 Ω terminaison 75 Ohms (positive)
VIDEO
PB/PR 0,7 Vc-c, 75 Ω terminaison 75 Ohms (positive)
L
AUDIO
DVI
AUDIO IN
FRANÇAIS
Pixels
Matrice active TFT
R
200 mV eff., 20 kOhms (maximum 3,0 Vc-c)
Prise Cinch (RCA)
RGB OUT
AUDIO OUT
REMARQUES
FRANÇAIS - 23
03CP-SX5500W02 01.10.24 1:20 PM ページ 24
FRANÇAIS - 24
LEGAL INFORMATION
FIVE-YEAR LIMITED WARRANTY
This Dukane LCD projector is warranted to the original purchaser for a period of
five (5) years from the original purchase date - in normal use and service against defects in material and workmanship. DUKANE CORPORATION
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
During the warranty period, Dukane Corporation will repair or replace (at the
manufacturer's option) any such defective parts (except for the lamp, which is
subject to whatever warranties the manufacturer may provide) without charge to
the purchaser for parts or labor when the product is returned, prepaid and insured,
with proof-of-purchase date. This remedy is void if the product has been
damaged by accident, unreasonable use, neglect, improper service or other
causes not arising out of defects in material or workmanship.
Dukane Corporation disclaims all liability for incidental or consequential damage
of any kind, including all damages arising out of any interruptions in operation of
the product and all damages to software.
No person, firm, or representative is authorized to assume any obligation or to
make any warranty on behalf of the Dukane Corporation other than as stated
above.
THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA.
FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.
LAMP REPLACEMENT SERVICE & REPAIR POLICY & PROCEDURE
For service and parts, contact the Dukane AV Service Department
at 1 (800) 676-2487 within the USA or 1 (630) 584-2300 worldwide.
If you would like to send a facsimile (FAX), dial 1 (630) 584-5156 worldwide.
When requesting warranty service, please have the sales receipt available along
with the model name and serial number.
If it becomes necessary to return the projector, use the original packing material
and box (if retained) or pack securely. Dukane Corporation will not be liable for
any pick-up or delivery charges or any expenses incurred for service calls or
service supplied by anyone other than the Dukane AV Service Department.
Audio Visual Products
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [email protected]
Phone: (630) 584-2300
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Part # 401-573-00

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project