null null

Built-In Wall Oven
Installation
Instructions
27” (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
30” (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Before You Begin
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE—This appliance must be properly
grounded.
Read these instructions carefully and completely.
•
IMPORTANT—Save these
instructions for local inspector’s use.
•
IMPORTANT—Observe all
•
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Parts Included
Materials Needed
(Appearance will vary)
Wire Nuts
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
27″ (68.6 cm)
Metal Bottom Trim
Strain Relief Clamp
for 1/2” conduit
Junction
Box
36” (91 cm)
of String
Optional 27″
(68.6 cm)
Metal Bottom
Trim Assembly
(on some models or
can be purchased
separately)
31-10647-1
Tools Needed
30″ (76.2 cm)
Metal Bottom Trim
Assembly
1/8” (3 mm) Drill Bit and
Electric or Hand Drill
03-07 JR
1
Phillips
Screwdriver
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
Electrical
Requirements cont.
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall
coverings around the oven can withstand
the temperatures (up to 200°F [93.3°C])
generated by the oven.
Rating plate is located on oven side trim,
side front frame or lower front frame.
Rating Plate
Location
We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician
show you where your main oven disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven
according to governing codes could result in a
hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the
requirements of the National Electrical Code,
ANSI/NFPA No. 70–Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not existing,
construction utilize a four-conductor connection to
an electric oven. When installing an electric oven
in new construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for
use with aluminum wiring must be used.
WARNING: The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Electrical
Requirements
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. See the
rating plate located on the oven frame to determine
the rating of the product. Use the chart below to
determine the minimum recommended dedicated
circuit protection.
KW Rating
240V
≤4.8 KW
4.9 KW–7.2 KW
7.3 KW–9.6 KW
9.7 KW–12.0 KW
KW Rating
208V
≤4.1 KW
4.3 KW–6.2 KW
6.3 KW–8.3 KW
8.4 KW–10.4 KW
Recommended
Circuit Size
(Dedicated)
20 Amp
30 Amp
40 Amp
50 Amp
2
Installation Instructions
Pre-Installation Checklist
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLE AND DOUBLE
OVEN INSTALLATION!
Open the oven door as far as it will go.
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
Push both hinge
locks down toward Hinge
the door frame,
Hinge
Slot
Slot
to the unlocked
position. This may
require a flat blade
screwdriver.
Hinge
Hinge
Unlocked
Unlocked
Position
Position
Hinge
Hinge
Arm
Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of
the door, and close the oven
door to the removal position,
which is most of the way closed.
Oven Racks
Lift door up and
out until the
hinge arms
clear the slots.
EASY
INSTA
LLA
TIO
EASY
INSTALLATION
OFNYOUR NEW
Before
30"
IMPOR you begin
WALL OF YO
30"
-Read WALL OVEN
IMPOR TANTOVEN UR NE
Save
these
Note TANTinstru
OBSE these
W
to
instru
Install
ctions
OWNE
RVE instructions
Before
you begin-Read
completely and carefully.
er- Bethese
comp
ALL ctions
Note- R- Keep
for inspector’s
GOVE
IMPORTANTthese sure
instructions
for local
letelyuse.
ThisSave these
to leave RNINGlocal inspec and
applia
IMPORTANT- OBSERVE
ALL
GOVERNING
CODES AND ORDIANCES.
instru
carefu
CODE
these
nce
tor’s
ctions
Note to Installer- Be suremust
to leave
these
with
the consumer.
S AND
instru
use. lly.
for instructions
be
ctions
future
ORDIA
OWNER- Keep these instructionsprope
for future
reference.
with
rly grounrefere
FOR
the NCES.
Note- This
appliance must be properly grounded
(if applicable).
nce.
YOUR
consu
ded
SAFE
(if applic
mer.
Before
TY
able).
instru you begin
carefu ctions comp-Read
lly. YOUR SAFETY
ELECTRICAL REQUIREMENTS
IMPORFOR
letely these
and
ELEC
instru TANTTRICA
ctionsyouSave
Before
begin-Read
IMPOR
Before you begin-Read
these these
L REQU these
Before
TANT for local
completely and
GOVEinstructions
IREME
instructions completely
and
instru you begin
RNING - OBSE inspec
NTS
Note carefully.
tor’s
carefully.
RVE
to Install CODE Save
carefu ctions comp-Read
use.
ALL
these
these IMPORTANTIMPORTANT- Save these
er- Be S AND
IMPOR lly.
letely these
instructions
localORDIA
inspector’s use.
OWNE instru
instructions for localand
inspector’s use.
sure
ctions for
instru TANTNCES
Rto leave
IMPORTANTOBSERVE
ALL
for future
Keep
with
Save OBSERVE ALL
IMPORTANT.
the AND ORDIANCES.
IMPORctions
these CODES
these
NoteGOVERNING
refere
instru consu
TANT for localCODES AND ORDIANCES.
GOVE GOVERNING
prope ThisNote
ctions
inspec
tonce.
Installer- Be
sure mer.
to leave
- OBSE
applia
RNING
Note
to
InstallerBe sure to leave
rly
Note
tor’s
RVE
nce
these instructions
with the consumer.
Before groun
to these CODE
instructionsALL
with theuse.
consumer.
ded must be
these Install
S AND
instru youOWNERKeep
these instructions
er- Be
begin (if
applic
OWNERKeep
these instructions
OWNE instru
ctions sure ORDIANCES
-Read
able).
carefu ctionsfor
future
reference.
R- Keep
for futurewith
reference.
to leave
comp
for future
these
.
IMPOR lly. Note- This
letelyappliance
must be
the
Note-these
This appliance
must be
Noteconsu
refere
and
instru
instru TANT-properly grounded
(if
applicable).
This
mer.
nce. grounded
properly
(if applicable).
Save
prope
ctions
applia
IMPORctions for
Beforethese
you begin-Read these
nceyou begin-Read these
Before
Beforerly groun
local
GOVE TANT- instructions
ded mustcompletely
instructions
and
OBSE inspeccompletely and
instru you begin
(if applicbe
Note RNING carefully.
CODE RVE ALL tor’s use.
-Read
carefully.
to
carefu ctions comp
able).
these Install
S AND
Save these
er-IMPORTANTIMPOR lly.
IMPORTANTSave these
letely these
OWNE instructionsBe sure ORDIA
andfor local inspector’s use.
instructions
for local
inspector’sinstru
use. TANT instructions
NCES
R- Keep
to leave
for future
with
. ALL IMPORctions - Save
IMPORTANTOBSERVE
the
these
IMPORTANTOBSERVE ALL
these
for local
Noterefere
instru consu
GOVERNING
CODES AND ORDIANCES.
GOVE TANTGOVERNING
inspec CODES AND ORDIANCES.
prope This appliance.
ctions mer.
OBSE
Note RNING
rly groun nceNote to Installer- Be sure to leave
tor’s Be sure to leave
RVE
Note
to InstallerCODE
to
use.
ALL
mustinstructions with the consumer.
these Install
ded these
S AND
instructions with the consumer.
er- these
(if applicbe
OWNE instructionsBeOWNEROWNER- Keep these instructions
sure ORDIA
Keep these instructions
able).
R- Keep
to leave NCES
for future
with
for future reference.
reference. .
the
thesefor future
Noteconsu
refere
Note- This appliance must be
instruThis
Noteappliance must be
prope This appliance.
ctions mer.
properly grounded (if applicable).
rly groun nce properly grounded (if applicable).
must
ded
(if applicbe
able).
Literature
Pack
Open oven door and remove literature
pack and oven racks.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges. Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Owner’s
Manual, Installations, etc. in a safe place
for future reference.
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 150 lbs. [68 Kg] single,
275 lbs. [124 Kg] double.)
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process. The trim is
wrapped separately and taped to
the top of the unit.
3
Installation Instructions
A
Cutout for 27″ (68.6 cm) Single Built-In
Ovens only
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Cabinet Width
5” (12.7 cm)
Max. from the
left or right
side
Cabinet
Width
27” (68.6 cm)
Allow 1” (2.5 cm)
for overlap of
oven over side
edges of cutout
2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Allow a minimum
of 20” (50.8 cm) for
clearance to adjacent
corners, drawers, walls,
etc. when door is open
Recommended
Cutout Location
from Floor
32 1/2” (82.6 cm)
Junction Box
Location
Cutout Width
25” (63.5 cm)
Min.
25 1/4” (64.1 cm)
Max.
Cutout
22” (55.9 cm)
Height
Min. above
27 5/8”
(70.2 cm) Min. base rail
28 1/8”
(71.4 cm) Max.
20” (50.8 cm)
Allow
1” (2.5 cm)
minimum for
overlap of
oven top and
bottom
of cutout
Recommended
cutout location
from floor 32 1/2”
(82.6 cm)
27” (68.6 cm)
Cutout Depth
23 1/2”
(59.7 cm) Min.
Cutout Width
25” (63.5 cm) Min.
25 1/4” (64.1 cm) Max.
Cutout Height
27 5/8” (70.2 cm) Min.
28 1/8” (71.4 cm) Max.
Alternate Junction
Box Location –
access from
adjacent cabinet
may be required
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4” (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
2"(5
x 4"
2” x 4”
cmor
x 10 cm) or
equivalent
runners level
Equivalent
withRunners
bottom of cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
single ovens, the runners and braces
must support 150 lbs (68 Kg).
24”
24"
(61 cm)
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
18" cm)
18” (45.7
27” 27"
(68.6 cm)
These ovens are not approved for
stackable installations.
4
Installation Instructions
A
Cutout for 27″ (68.6 cm) Double Built-In
Ovens only
For JKP35, JKP55, JKP75, PK956, ZEK958 models only.
Allow 1” (2.5 cm)
for overlap of
oven over side
edges of cutout
5”
(12.7 cm)
Max. from
the left or
Cabinet
right
Width
side
27”
(68.6 cm)
Cutout
Width
25” (63.5 cm) Min.
25 1/4”
(64.1 cm) Max.
Cabinet Width
Junction Box
Location
44”
(111.8 cm)
Min.
Above
base rail
Cutout
Height
49 11/16”
(126.2 cm) Min.
50 1/8”
(127.3 cm) Max.
2” x 4”
(5 cm x 10 cm)
or equivalent
runners
Allow a minimum
of 20” (50.8 cm)
for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
Recommended
cutout location
from floor 13 1/4”
(33.7 cm)
If the cabinet does not have a solid bottom,
two braces or runners must be installed to
support the weight of the oven. For double
ovens, the runners and braces must
support 300 lbs (135 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
Recommended
Cutout Location
from Floor
13 1/4” (33.7 cm)
Cutout Depth
23 5/8” (60 cm) Min.
Cutout Width
25” (63.5 cm) Min.
25 1/4” (64.1 cm) Max.
Cutout Height
49 11/16” (126.2 cm) Min.
50 1/8” (127.3 cm) Max.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4”
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
20” (50.8 cm)
Allow 1”
(2.5 cm) for
overlap of oven
top and bottom
of cutout
27” (68.6 cm)
CL
2”x x4"4”
2"
or
EQUIVALENT
(5 cm x 10 cm)
RUNNERS
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners
18"
18”
OVER
CENTERLINE
(45.7
cm)
OF CABINET
Over Centerline
of Cabinet
5
Installation Instructions
A
Cutout for 27″ (68.6 cm) Single Built-In
Ovens only Under Counter
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
240V / 208V
Junction Box
5”
Location
(12.7 cm)
Max. from the
left or right
side
25” (63.5 cm)
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
25” (63.5 cm) Min.
25 1/4” (64.1cm) Max.
27 5/8” (70.2 cm) Min.
28 1/8” (71.4 cm) Max.
Allow
1”
(2.5 cm)
unit overlap top
and bottom of
oven, 1” (2.5 cm)
unit overlap side
edges
Gas and electrical connections
for gas cooktop must be located
in an adjacent accessible
location to the right.
22” (55.9 cm) Min.
Above Support
Platform
36” (91.4 cm)
Typical
Countertop
Height
24” (61cm)
4” (10.2 cm)
Typical
Toekick
3/4” (1.9 cm)
Support Platform
Required
Must
match
toekick
height
MUST SUPPORT 150 LBS. (68 Kg)
NOTE: This oven is not approved to be
installed under a solid disk, induction
or downdraft modular cooktop.
6
Cabinetry
A
Cutout for 27″ (68.6 cm) Single or
Double Built-In Ovens only – Over a
Warming Drawer
For JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938,
ZEK958 models only.
Single 27″ (68.6 cm)
Oven Over
a Warming Drawer
Double 27″ (68.6 cm)
Oven Over
a Warming Drawer
Anti-Tip Block
Against Rear
Wall Per
Warming
Drawer
Requirement
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2” (5.1 cm)
Min.
2” (5.1 cm)
Min.
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Per
Warming
Drawer
Requirement
Per Warming
Drawer
Requirement
1” (2.5 cm) Min. Above Toekick
1” (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
• When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
7
Cabinetry
A
Cutout for 27″ (68.6 cm) Single Ovens only –
Below an Advantium or Microwave Oven
or Between an Advantium or Microwave
Oven and a Warming Drawer
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Single 27″ (68.6 cm) Oven
Below an Advantium or
Microwave Oven
Per Advantium or
Microwave Oven
Requirement
Single 27″ (68.6 cm) Oven
Between an Advantium or
Microwave Oven and a
Warming Drawer
Per Advantium or
Microwave Oven
Requirement
2” (5.1 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
2” (5.1 cm) Min.
2” (5.1 cm) Min.
Per Warming
Drawer
Requirement
NOTE: The middle rail separating the two
openings may need to be larger than the 3”
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the 2”
(5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Combined Advantium or Microwave
Oven and Wall Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
• Refer to the Advantium or microwave
oven installation instructions for electrical
requirements of that product.
• These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Warming Drawer Combined with
Advantium or Microwave Oven and
Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
8
Installation Instructions
A
Cutout for 30″ (76.2 cm) Single Built-In
Ovens only
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Cutout
Width
CUTOUT
28 1/2”
(72.4 cm)
WIDTH
28 1/2"
MIN.
Min.
5/8"(72.7
MAX.cm)
2828
5/8”
Max.
Allow 11/16”
(1.75 cm) for
ALLOW 11/16"
FOR
overlap
of oven
OVERLAP
OF THE
over
side edges
OVER SIDE
ofOVEN
cutout
EDGES OF CUTOUT
Opening
Between
THE OPENING
Inside INSIDE
Walls
BETWEEN
Must Be
WALLS
MUST
BEAt
ATLeast
LEAST
28
281/2"WIDE
1/2”
(72.4 cm)
Wide
7 3/4” (19.7 cm)
Max.
Junction Box
5"
Location
(junction box
may be
located in
JUNCTION
adjacent BOX
LOCATION
cabinet)
Cutout
Height
27CUTOUT
1/4”
HEIGHT
(69.2
cm)
Min.
27 1/4"
MIN.
275/16"
5/16”MAX.
27
(69.4 cm) Max.
ALLOW
AllowAaMINIMUM
minimum
OF 21" FOR CLEARANCE
of 21” (53.3
cm) for
TO ADJACENT
CORNERS,
clearance
to adjacent
DRAWERS,
WALLS
ETC.
WHEN THE
DOORdrawers,
IS OPENED.
corners,
walls, etc. when
door is open
30” (76.2 cm)
Recommended
Cutout Location
from Floor
32 1/2” (82.6 cm)
Cutout Depth
23 1/2” (59.7 cm) Min.
Cutout Width
28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
TOcm)
22” 22"
(55.9
BOTTOM
Min. toOF
JUNCTION BOX
Cutout Height
Bottom of
Junction Box
21” (53.3 cm)
21"
Allow
1” 1"
(2.5
cm)
ALLOW
FOR
OVERLAPfor
minimum
ON OVEN
overlap
of TOP
oven
AND BOTTOM
top
11⁄4”
OF and
CUTOUT
(3.2 cm) overlap
of oven bottom
ofCABINET
cutout
WIDTH
Cabinet
30"
Width
30” (76.2 cm)
Cabinet Width
27 1/4” (69.2 cm) Min.
27 5/16” (69.4 cm) Max.
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4” (1.9 cm)
thick, shim both sides equally to
establish the cutout width.
RECOMMENDED
Recommended
CUTOUT
LOCATION
cutout
location
32 1/2"
from
floor
32 1/2”
FROM
THE
(82.6FLOOR
cm)
CL
runners level
with bottom
of cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
Suitable
ovens, the runners and braces must
Bracing
support 150 lbs (68 Kg).
to Support
SUITABLE
Runners
BRACING
TO SUPPORT
RUNNERS
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
2"2”
x x
4" 4”
or
EQUIVALENT
(5 cm x 10 cm)
RUNNERS
or equivalent
21
5/8”
21 5/8"
OVER
(54.9CENTERLINE
cm) Over
OF CABINET
Centerline
of Cabinet
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2″ (5.1 cm) min. between cutouts.
2″ (5.1 cm)
Cutout –
Min.
Observe all
dimensions
and
requirements.
These ovens are not approved for
stackable installations.
9
Cutout –
Observe all
dimensions
and
requirements.
Installation Instructions
A
Cutout for 30″ (76.2 cm) Double Built-In Ovens only
For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.
Cutout
Width
CUTOUT
28 1/2”
(72.4 cm)
WIDTH
28 1/2"
Min.MIN.
28 5/8" MAX.
28 5/8” (72.7 cm)
Max.
ALLOW 11/16"
FOR OVERLAP
Allow
OF11/16”
THE OVEN
(1.75
cm)
forEDGES
OVER
SIDE
overlap
of oven
OF CUTOUT
over side edges
of cutout
Allow a minimum
ALLOW A MINIMUM OF 21"
of 21” (53.3 cm) for
FOR CLEARANCE TO
clearance
to adjacent
ADJACENT CORNERS,
corners,
DRAWERS,drawers,
WALLS ETC.
walls,
etc.THE
when
WHEN
DOOR
door is
IS open
OPENED.
7 3/4”
(19.7 cm) Junction Box
Max. Location
5"
(junction box
may be
located in
adjacentBOX
JUNCTION
cabinet)
LOCATION
Cabinet Width
30” (76.2 cm)
Recommended
Cutout Location
from Floor
12” (30.5 cm)
Cutout Depth
23 1/2” (59.7 cm) Min.
Cutout Width
28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Opening
Between
Inside
Walls
THE OPENING
Must
Be AtINSIDE
BETWEEN
WALLS
MUST
Least
28 1/2”
BE AT
LEAST
(72.4
cm)
Wide
28 1/2"WIDE
Allow 1” (2.5 cm)
minimum for
overlap of oven
ALLOW
1"1FOR
1
top
and
⁄”
OVERLAP4
(3.2
overlap
ON cm)
OVEN
TOP
of
oven
bottom
AND
BOTTOM
OF
of CUTOUT
cutout
Cutout Height
51 13/16” (131.6 cm) Min.
51 15/16” (131.9 cm) Max.
47” 47"
(119.4
TO cm)
BOTTOM
Min. OF
JUNCTION
BOX
to Bottom
of
Junction Box
Cutout
Height
51 CUTOUT
13/16” (131.6 cm)
HEIGHT
Min.
51 13/16" MIN.
51
15/16”MAX.
(131.9 cm)
51 15/16"
Max.
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4” (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
21” (53.3 cm)
21"
30"
30”
(76.2
cm)
CABINET
WIDTH
Cabinet
Width
Recommended
RECOMMENDED
CUTOUT
LOCATION
cutout
location
12"
FROM
from
floorTHE
12”FLOOR
(30.5 cm)
If the cabinet does not have a solid bottom,
Suitable
two braces or runners must be installed
Bracing
level with the bottom of the cutout to
to Support
Runners
support the weight of the oven. For
double ovens, the runners and braces
must support 275 lbs (124 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
10
CL
2”x x4"4”
2"
or
EQUIVALENT
(5 cm x 10 cm)
RUNNERS
or equivalent
runners level
with bottom
of cutout
21
5/8”
21 5/8"
OVER
(54.9CENTERLINE
cm) Over
OF CABINET
Centerline
of Cabinet
Installation Instructions
A
Cutout for 30″ (76.2 cm) Single Built-In Ovens
only Under Counter
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Gas or electric cooktops may be installed over this oven. See
cooktop installation instructions for cutout size. See label on
top of oven for approved cooktop models.
240V / 208V
Junction Box
Location (junction
box may be in
adjacent cabinet)
7 3/4”
(19.7 cm)
Max.
25” (63.5 cm)
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
27 1/4” (69.2 cm) Min.
27 5/16” (69.4 cm) Max.
Allow 1” (2.5 cm)
overlap top
of oven,
11/16” (1.8 cm)
overlap side edges
of cutout and
1 1/4” (3.2 cm)
overlap bottom
of oven.
Gas and electrical connections
for 30” (76.2 cm) gas cooktop must
be located in an adjacent accessible
location to the right. For 36” (91.4 cm)
gas cooktop, the connections may be
made to the left.
22” (55.9 cm) Min.
Above Support
Platform
36” (91.4 cm)
Typical
Countertop
Height
24” (61 cm)
4” (10.2 cm)
Typical
Toekick
3/4” (1.9 cm)
Support Platform
Required
Must
match
toekick
height
MUST SUPPORT 150 LBS. (68 Kg)
NOTE: This oven is not
approved to be installed
under a solid disk, induction
or downdraft modular
cooktop.
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2″ (5.1 cm) min. between cutouts.
Cutout –
Observe all
dimensions
and
requirements.
11
2″ (5.1 cm )
Min.
Cutout –
Observe all
dimensions
and
requirements.
Cabinetry
A
Cutout for 30″ (76.2 cm) Single or Double
Built-In Ovens only – Over a
Warming Drawer
For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960,
ZET938, ZET958 models only.
Double 30″ (76.2 cm)
Oven Over a Warming
Drawer
Single 30″ (76.2 cm)
Oven Over a Warming
Drawer
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2” (5.1 cm)
Min.
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Per Warming
Drawer
Requirement
Anti-Tip Block
Against Rear
Wall Per
Warming
Drawer
Requirement
2” (5.1 cm)
Min.
Per Warming
Drawer
Requirement
1” (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
1” (2.5 cm) Min. Above Toekick
• When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
12
Cabinetry
A
Cutout for 30″ (76.2 cm) Single Ovens only –
Below an Advantium or Microwave Oven
or Between an Advantium or Microwave
Oven and a Warming Drawer
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Single 30″ (76.2 cm) Oven
Below an Advantium or
Microwave Oven
Per Advantium or
Microwave Oven
Requirement
Single 30″ (76.2 cm) Oven
Between an Advantium or
Microwave Oven and a
Warming Drawer
Per Advantium or
Microwave Oven
Requirement
2” (5.1 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
NOTE: The middle rail separating the two
openings may need to be larger than the 2”
(5.1 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
2” (5.1 cm) Min.
2” (5.1 cm) Min.
Per Warming
Drawer
Requirement
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the
2” (5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Combined Advantium or Microwave
Oven and Wall Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
• Refer to the Advantium or microwave
oven installation instructions for electrical
requirements of that product.
• These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Warming Drawer Combined with
Advantium or Microwave Oven and
Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
13
Installation Instructions
B
Electrical Connections
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
B1
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
B2
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the
electrical junction box as shown below.
Position the conduit in such a manner
that it will lie on top of the oven in
a natural loop when the oven is
installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
Junction Box
Location
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
GROUND
WIRE
Conduit
BARE
GROUND
RED
WHITE
BLACK
WARNING: Improper
Place oven on a
support to assist in
connecting conduit
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer’s recommended
procedure closely.
14
Strain Relief Clamp
(not included)
must be used at
Junction Box
Installation Instructions
B3 New Construction and
Four-Conductor Branch
Circuit Connection
B4 Three-Conductor Branch
Circuit Connection
When connecting to a three-conductor branch
circuit, if local codes permit:
• When installing in new construction, or
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
• When installing in a mobile home, or
• When installing in a recreational vehicle, or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
Ground and
Neutral Wires
Ground
Wire
Junction Box
Cover
b. Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
Junction Box
Cover
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using a wire nut. If the residence
red, black or white leads are aluminum
conductors, see WARNING on page 14.
b. Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING on page 14.
d. Install Junction Box Cover.
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
d. Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see WARNING
on page 14.
e. Install Junction Box Cover.
15
Installation Instructions
C
Securing the Oven in the Opening
C1 Sliding the Oven Into the
Opening
C2 Drilling the Pilot Holes and
Mounting the Oven
a. Loop (do not tie) a 36” (91 cm) string
around the conduit before the oven is slid
into place. This will keep the conduit from
falling behind the oven.
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.
Pull out on
string loop
while pushing
the oven into
the cabinet
Mounting
Hole
Locations
(Hole
Locations
may vary)
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
The screws must
be a minimum of
1/4” (6 mm) from
the front of the
cutout.
WARNING: Mounting
screws must be used. Failure to
do so could result in the oven
falling out of the cabinet causing
serious injury.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 3/4” particle board screws.
These may be purchased at any hardware
store.
16
Installation Instructions
C3 Preparing for the Bottom
Trim Installation
C4 Installing the Metal
Bottom Trim
a. With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
a. Place the bottom metal trim centered over
the pre-drilled mounting holes. Tape the
edges of the trim down to maintain the
alignment.
b. Using the trim
as a template,
mark the center
of each slot
(two total) where
the mounting holes
will be drilled.
c. Remove the trim.
d. Drill pilot holes into
the center of each
template mark.
For 27″ (68.6 cm)
models with Lower
Trim in Position,
Mark (2) Mounting
Hole Locations
here
* Remove
Lower Trim
Before
Pre-drilling
Mounting
Holes
b. Using two trim screws provided, secure
the bottom trim to the bottom edge of the
cabinet.
Side
Trim
Trim Screw Locations for
27″ (68.6 cm) models with
Lower Trim
Side
Trim
*
For 30″ (76.2 cm)
models with
Lower Trim in
Position, Mark
(2) Mounting
Hole Locations
here
Metal Lower Trim
Trim Screw Locations for
30″ (76.2 cm) models with
Lower Trim
IMPORTANT: If this unit is ever
removed from the cabinet or the oven
is ever pulled out for service, the trim
must be removed first or damage to
the trim will occur.
17
Installation Instructions
D
Replacing the Oven Door
NOTE: The oven door is heavy. You
may need help lifting the door high
enough to slide it into the hinge slots.
Do not lift the door by the handle.
D1
D3
Open the oven door as far as it
will open.
D4
Push the hinge locks up against the
front frame of the oven cavity, to the
locked position.
Hinge in
Locked Position
Lift the oven door by
placing one hand on
each side. The door is
heavy, so you may need
help. Do not lift the door
by the handle.
Notch of Hinge
Securely Fitted
into Bottom of
Hinge Slot
D5
D2
With the door at the same angle as
the removal position, which is most of
the way closed, seat the notch of the
hinge arm into the bottom edge of the
hinge slot. The notch of the hinge arm
must be fully seated into the bottom
of the slot.
Hinge Arm
Bottom Edge
of Slot
Hinge Notch
18
Close the oven door.
Installation Instructions
Pre-Test Checklist
Remove all protective film, if present,
and any stickers.
Check that the bottom trim is installed
properly (see page 17).
Check to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check to be sure the mounting screws
are installed and flush with the side trim
(see page 16).
Operation Checklist
Remove all items from the inside
of the oven.
NOTE TO ELECTRICIAN: The power
leads supplied with this appliance
are UL recognized for connections
to larger gauge household wiring.
The insulation of these leads is
rated at temperatures much higher
than the temperature rating of
household wiring. The current
carrying capacity of a conductor
is governed by the wire gauge and
also the temperature rating of the
insulation around the wire.
Check that conduit is securely
connected to the junction box.
Turn on the power to the oven. (Refer
to your Owner’s Manual.) Verify that
the bake and broil units, and all
cooking functions operate properly.
Check that the circuit breaker is not
tripped nor the house fuse blown.
NOTE: ALUMINUM WIRING
See your Owner’s Manual for
troubleshooting list.
WARNING: IMPROPER
CONNECTION OF ALUMINUM
HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL HAZARD OR FIRE.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum,
and follow the manufacturer’s
recommended connector
procedure closely.
NOTE: Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice
and local codes.
A.
19
Notes
20
Horno de pared empotrado
Modelos de 27” (68,6 cm)
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
Modelos de 30” (76,2 cm)
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
IMPORTANTE—Observe todos
•
•
•
Moldura de fondo
metálica de 27″
(68,6 cm)
31-10647-1
Una broca de 1/8” (3 mm) para
taladro eléctrico o manual
03-07 JR
1
2
¡TODA LA INFORMACIÓN PARA LA
INSTALACIÓN EN LAS PÁGINAS
SIGUIENTES ES PARA SER USADA EN
LA INSTALACIÓN DE HORNOS DE UNA
O DOS UNIDADES!
Hinge
Ranura
Slot
de la
bisagra
Brazo
Hinge de
laArm
bisagra
¡NO LEVANTE LA PUERTA POR
LA EMPUÑADURA!
EASY
INSTA
LLA
TIO
EASY
INSTALLATION
OFNYOUR NEW
Before
30"
IMPOR you begin
WALL OF YO
30"
-Read WALL OVEN
IMPOR TANTOVEN UR NE
Save
these
Note TANTinstru
OBSE these
W
to
instru
Install
ctions
OWNE
RVE instructions
Before
you begin-Read
completely and carefully.
er- Bethese
comp
ALL ctions
Note- R- Keep
for inspector’s
GOVE
IMPORTANTthese sure
instructions
for local
letelyuse.
ThisSave these
to leave RNINGlocal inspec and
applia
IMPORTANT- OBSERVE
ALL
GOVERNING
CODES AND ORDIANCES.
instru
carefu
CODE
these
nce
tor’s
ctions
Note to Installer- Be suremust
to leave
these
with
the consumer.
S AND
instru
use. lly.
for instructions
be
ctions
future
ORDIA
OWNER- Keep these instructionsprope
for future
reference.
with
rly grounrefere
FOR
the NCES.
Note- This
appliance must be properly grounded
(if applicable).
nce.
YOUR
consu
ded
SAFE
(if applic
mer.
Before
TY
able).
instru you begin
carefu ctions comp-Read
lly. YOUR SAFETY
ELECTRICAL REQUIREMENTS
IMPORFOR
letely these
and
ELEC
instru TANTTRICA
ctionsyouSave
Before
begin-Read
IMPOR
Before you begin-Read
these these
L REQU these
Before
TANT for local
completely and
GOVEinstructions
IREME
instructions completely
and
instru you begin
RNING - OBSE inspec
NTS
Note carefully.
tor’s
carefully.
RVE
to Install CODE Save
carefu ctions comp-Read
use.
ALL
these
these IMPORTANTIMPORTANT- Save these
er- Be S AND
IMPOR lly.
letely these
instructions
localORDIA
inspector’s use.
OWNE instru
instructions for localand
inspector’s use.
sure
ctions for
instru TANTNCES
Rto leave
IMPORTANTOBSERVE
ALL
for future
Keep
with
Save OBSERVE ALL
IMPORTANTctions
.
the
these CODES
these
NoteGOVERNING
AND ORDIANCES. IMPORGOVERNING
for localCODES
refere
AND ORDIANCES.
instru consu
GOVE TANTprope ThisNote
ctions
inspec
tonce.
Installer- Be
sure mer.
to leave
applia
OBSE
RNING
Note
to
InstallerBe sure to leave
rly
Note
tor’s
RVE
nce
these instructions
with the consumer.
Before groun
to these CODE
instructionsALL
with theuse.
consumer.
ded must be
these Install
S AND
instru youOWNERKeep
these instructions
er- Be
begin (if
applic
OWNERKeep
these instructions
OWNE instru
ctions sure ORDIANCES
-Read
able).
carefu ctionsfor
future
reference.
R- Keep
for futurewith
reference.
to leave
comp
for future
these
.
IMPOR lly. Note- This
letelyappliance
must be
the
Note-these
This appliance
must be
Noterefere
and
instru consumer.
instru TANT-properly grounded
(if
applicable).
This
nce.
properly grounded
(if applicable).
Save
prope
ctions
applia
IMPORctions for
Beforethese
you begin-Read these
nceyou begin-Read these
Before
Beforerly groun
local
GOVE TANT- instructions
ded mustcompletely
OBSE inspeccompletely and
instructions
and
instru you begin
(if applicbe
Note RNING carefully.
CODE RVE ALL tor’s use.
-Read
carefully.
to
carefu ctions comp
able).
these Install
S AND
Save these
er-IMPORTANTIMPOR lly.
letely these
IMPORTANTSave these
OWNE instructionsBe sure ORDIA
and
instructions
for local
inspector’sinstru
use. TANT instructions for local inspector’s use.
NCES
R- Keep
to leave
for future
with
. ALL IMPORctions - Save
IMPORTANTOBSERVE
the
these
IMPORTANTOBSERVE ALL
these
for local
Noterefere
instru consu
GOVERNING
CODES AND ORDIANCES.
GOVE TANTGOVERNING
inspec CODES AND ORDIANCES.
prope This appliance.
ctions mer.
OBSE
Note RNING
rly groun nceNote to Installer- Be sure to leave
tor’s Be sure to leave
RVE
Note
to InstallerCODE
to
use.
ALL
mustinstructions with the consumer.
these Install
ded these
S AND
instructions with the consumer.
er- these
(if applicbe
OWNE instructionsBeOWNEROWNER- Keep these instructions
sure ORDIA
Keep these instructions
able).
R- Keep
to leave NCES
for future
with
for future reference.
reference. .
the
thesefor future
Noteconsu
refere
Note- This appliance must be
instruThis
Noteappliance must be
prope This appliance.
ctions mer.
properly grounded (if applicable).
rly groun nce properly grounded (if applicable).
must
ded
(if applicbe
able).
Bisagra sale
de la ranura
3
Altura
del corte
27 5/8” (70,2 cm) Mín.
28 1/8” (71,4 cm) Máx.
20” (50,8 cm)
Ancho del
gabinete
27” (68,6 cm)
32 1/2” (82,6 cm)
23 1/2” (59,7 cm) Mín.
25” (63,5 cm) Mín.
25 1/4” (64,1 cm) Máx.
Altura de corte
27 5/8” (70,2 cm) Mín.
28 1/8” (71,4 cm) Máx.
18” 18"
(45,7 cm)
27”27"
(68,6 cm)
Ancho del
gabinete
Ancho del
gabinete
27” (68,6 cm)
2” x 4”
(5 cm x 10 cm)
o correderas
equivalentes
13 1/4” (33,7 cm)
23 5/8” (60 cm) Mín.
25” (63,5 cm) Mín.
25 1/4” (64,1 cm) Máx.
49 11/16” (126,2 cm) Mín.
50 1/8” (127,3 cm) Máx.
Altura de corte
20” (50,8 cm)
27” (68,6 cm)
CL
Abrazaderas
de soporte
adecuadas
para las
SUITABLE
correderas
BRACING
TO SUPPORT
RUNNERS
18"
18”
OVER
CENTERLINE
(45,7
cm)
OF CABINET
5
25” (63,5 cm)
25” (63,5 cm) Mín.
25 1/4” (64,1 cm) Máx.
27 5/8” (70,2 cm) Mín.
28 1/8” (71,4 cm) Máx.
36” (91,4 cm)
Altura típica del
gabinete
24” (61 cm)
4” (10,2 cm)
Zócalo típico
Plataforma de
3/4” (1,9 cm)
de soporte
requerida
DEBE SOPORTAR 150 LIBRAS
(68 Kg)
Gabinetes
A
7
Gabinetes
A
Por Advantium o horno
de microondas requisitos
Por Advantium o horno
de microondas requisitos
2” (5,1 cm) Mín.
2” (5,1 cm) Mín.
2” (5,1 cm) Mín.
ALLOW 11/16" FOR
OVERLAP OF THE
Permita 11/16”
OVEN OVER SIDE
(1,75 cm) para
EDGES OF CUTOUT
7 3/4”
(19,7 cm)
Máx.
5"
30” (76,2 cm)
32 1/2” (82,6 cm)
23 1/2” (59,7 cm) Mín.
28 1/2” (72,4 cm) Mín.
28 5/8” (72,7 cm) Máx.
27 1/4” (69,2 cm) Mín.
27 5/16” (69,4 cm) Máx.
21” (53,3 cm)
21"
CL
Abrazaderas
de soporte
adecuadas
para
las
SUITABLE
correderas
BRACING
TO SUPPORT
RUNNERS
2”x x
2"
4" 4”
or
EQUIVALENT
(5 cm x 10
RUNNERS
21
5/8”
21 5/8"
OVER CENTERLINE
(54,9
Línea de
OFcm)
CABINET
centro sobre
gabinetes
2″ (5,1 cm)
Mín.
Corte para los hornos de dos
unidades de 30″ (76,2 cm) solamente
Para los modelos JTP35, JTP55, JTP75, PT956, PT960, ZET958 solamente.
Ancho
del corte
28 1/2”
CUTOUT
WIDTH
(72,4
cm) Mín.
28 28
1/2"5/8”
MIN.
28 5/8" MAX.
(72,7 cm) Máx.
30” (76,2 cm)
12” (30,5 cm)
23 1/2” (59,7 cm) Mín.
28 1/2” (72,4 cm) Mín.
28 5/8” (72,7 cm) Máx.
51 13/16” (131,6 cm) Mín.
51 15/16” (131,9 cm) Máx.
21” (53,3 cm)
21"
CL
30"
Ancho del
gabinete
CABINET
WIDTH
30” (76,2
cm)
el piso 12” (30,5 cm)
10
Abrazaderas
de soporte
adecuadas
para
las
SUITABLE
correderas
BRACING
TO SUPPORT
RUNNERS
21 5/8"
21
5/8”
OVER CENTERLINE
(54,9OFcm)
Línea de
CABINET
centro sobre
gabinetes
25” (63,5 cm)
28 1/2” (72,4 cm) Mín.
28 5/8” (72,7 cm) Máx.
27 1/4” (69,2 cm) Mín.
27 5/16” (69,4 cm) Máx.
36” (91,4 cm)
Altura típica del
gabinete
24” (61 cm)
4” (10,2 cm)
Zócalo típico
Plataforma de
3/4” (1,9 cm)
de soporte
requerida
DEBE SOPORTAR 150 LIBRAS (68 Kg)
2″ (5,1 cm)
Mín.
Gabinetes
A
12
Gabinetes
A
Horno individual de 30″ (76,2 cm)
debajo de un horno Advantium o
un horno de microondas
Por Advantium o horno
de microondas requisitos
2” (5,1 cm) Mín.
Por Advantium o horno de
microondas requisitos
2” (5,1 cm) Mín.
2” (5,1 cm) Mín.
ATENCIÓN AL
INSTALADOR:
B1
B2
Conducto
ROJO
BLANCO
NEGRO
ADVERTENCIA:
14
ADVERTENCIA:
16
de fondo metálica
Moldura
lateral
17
D1
D3
D4
D5
D2
18
NOTA: CABLEADO DE ALUMINIO
A.
ADVERTENCIA:
19
Notas
20

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project