Wilson Electronics 811201 Installation guide

Wilson Electronics 811201 Installation guide
Signal Booster
Installation
Guide
Direct Connect
Signal Boosters
Contents:
How it Works. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-Vehicle Wilson Installation
Outside Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Lightning Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . 6
In-Building Wilson Installation
Outside Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Powering Up a Wilson Signal Booster. . . . . . . . . . . . . . . . 8
Warnings and Recommendations. . . . . . . . . . . . . . . . . . . 9
Guarantee and Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal Booster Specifications . . . . . . . . . . . . . . Back Cover
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to do
so could be hazardous and result in damage to your Signal Booster.
Wilson
®
Electronics, Inc.
Installation Instructions for the Following Wilson Electronics Signal Boosters
Direct Connect 800/1900 MHz with GPS amplification – Model # 2B1401
FCC ID: PWO2B1401SA IC: 4726A-2B1401SA
The term “IC” before the radio certification number only signifies that Industry Canada technical
specifications were met.
Antenna Options and Accessories
800 MHz Yagi Cellular Antenna (301111)
Lightning Surge Protector
75 Ohm (859988)
Lightning Surge Protector
50 Ohm (859902)
1900 MHz Yagi PCS Antenna (301124)
800 MHz Yagi Cellular
Antenna (301129)
12v DC
Hardwire
Power Supply
(859905)
Mini
Magnet
Dual-Band
(301113)
Magnet
Mount
Dual-Band
(301103)
Trucker
Mount
Dual-Band
(301101)
Marine
Antenna
Dual-Band
(301130)
NMO
Mount
Dual-Band
(301104)
How it Works
Wilson Electronics Signal Boosters are small, portable, bi-directional devices that deliver
service levels consistent with what would be expected in areas of high cell network
coverage. They amplify a weak or shadowed signal in mobile, marine, M2M and in-building
applications.
When using a Wilson Electronics Signal Booster in conjunction with Wilson Electronics
antennas, the outside antenna will collect the cell tower signal and send it through the
cable to the Signal Booster adapter. Cell phones and cellular data cards (laptops) then
communicate with the improved signal. When a cellular device transmits, the signal is
amplified by the Signal Booster and broadcasted back to the cell tower through the outside
antenna.
1
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
Before Getting Started
This guide will help you properly install Wilson’s Direct Connect Signal Boosters in both
in-vehicle and in-building applications. It is important to read through all of the
installation steps for your particular application prior to installing any equipment.
Read through the instructions, visualize where all the equipment will need to be installed
and do a soft installation before mounting any equipment. If you have any questions
contact Wilson Electronics Technical Support at 866-294-1660.
Inside this Package
• Direct connect Signal Booster
• DC plug-in power supply
• 6’ inside antenna extension cable
Note: Products may vary due to product kit purchases.
Direct Connect
Signal Booster
DC plug-in power
supply
6‘ inside
antenna
extension
cable
Additional Required Equipment
• Outside antenna for in-vehicle or in-building use (required)
(NOTE: Specifically tuned iDEN antennas available)
• Cell phone or data card specific external antenna adapter (required)
• AC/DC power supply (required for in-building use)
In addition to Dual-Band cellular signal amplification, the 811201 Dual-Band Direct
Connect Signal Booster incorporates GPS signal amplification. The amplified GPS
signal enhances the performance of any GPS applications which your phone may
support, including the E911 emergency location feature if your phone is so
equipped. In emergencies, E911 enabled phones provide caller location to 911
call centers.
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
2
In-Vehicle
Installing a Wilson Outside Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof at least 12
inches away from any other antennas and free of obstructions.
Follow the specific antenna installation instructions included with the outside antenna (sold
separately).
Optional MagnetMount Antenna
Shown
Carefully
Pull Down
Door Seal
Run Cable
Under
Seal
The outside antenna must be installed
vertically. Signal performance will be
degraded if the antenna is not vertical.
Run the antenna cable through the door to
the Signal Booster.
For a more professional looking installation,
run the antenna cable under the door seal.
Carefully pull down the door seal. Run the
cable through the seal and push the seal
back into place. This prevents constant
wear and tear on the cable as the door
opens and closes.
The antenna cable is small enough to easily
tuck under the door seal or plastic molding.
Tuck Cable
Under Seal
NOTE: See RF Safety Warnings (p. 9)
3
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
In-Vehicle
Installing a Wilson Signal Booster
Select a location to install the Signal
Booster that is away from excessive heat,
direct sunlight, moisture and that has proper
ventilation.
Recommended installation locations for
in-vehicle are:
• Under the seat
• In the trunk
• Under the dash
Run the cable from the outside antenna and
attach it to the connector labeled “Outside
Antenna” on the Signal Booster.
!
Outside
Antenna
Warning: Do not plug in the DC Power
Supply until the Outside Antenna and
external adapter cables are attached to
the Signal Booster.
Cell Phone
DC Power
Supply
Adapter
Signal Booster
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
4
In-Vehicle/In-Building
Installing a Wilson External Adapter
An external adapter is required to connect the cell phone or cellular data card to the Signal
Booster. The external adapter is cell phone/data card-specific and may be purchased
through a local retailer.
Sample
external
adapter
Refer to Wilson’s Adapter Guide to identify
the right adapter for your cell phone or
cellular data card. The adapter guide is
available through a local retailer or visit
www.WilsonElectronics.com.
The external adapter plugs into the included six-foot extension cable and directly into a
socket on the cell phone or cellular data card as shown in Figure 1. (NOTE: See the user’s
manual for your specific phone or data card to determine the socket location.)
Run the extension cable from the external adapter on the cell phone or cellular data card
and attach it to the connector labeled “Inside Antenna” on the Signal Booster.
NOTE: Depending on your
specific cell phone, the adapter
socket may be located beneath a
rubber plug.
Figure 1
5
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
In-Vehicle/In-Building
Extension Cable Chart
The following Wilson extension cables are available to help you customize your installation
for peak performance.
951101
5’ Extension Cable RG58U
Low Loss Coax
951102
10’ Extension Cable RG58U
Low Loss Coax
951103
15’ Extension Cable RG58U
Low Loss Coax
951104
20’ Extension Cable RG58U
Low Loss Coax
952320
952330
952350
20’ Extension Cable Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
30’ Extension Cable Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
50’ Extension Cable Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
952375
952400
952302
951110
75’ Extension Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
100’ Extension Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
2’ Extension Wilson 400
(9913 Equivalent)
Ultra Low Loss Coax
(N-Male to N-Male Ends)
2’ Extension RG58U Low
Loss Coax (N-Male to FMEFemale)
RG58U - FME connectors / 9913 - N connectors
Installing Lightning Protection
Install the Lightning Surge Protector (LSP) close
to the Signal Booster. Attach the cable from the
outside antenna to the surge protector. Using a
short length of low loss cable, attach one end to
the LSP and the other to the outside antenna.
Ensure the LSP is properly grounded. (For RG6
cable use #859988-75 Ohm, For 50 Ohm use Part
#859902).
From the
outside
antenna
Ground Wire
Lightning Surge
Protection
To the Signal Booster
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
6
In-Building
Installing a Wilson Outside Antenna – In-Building
Select a location on the roof of the building to install the outside antenna that has the most
unobstructed line of sight to the cell tower.
A Yagi antenna must be installed horizontally with the elements vertical and the drip hole
on the bottom. Ensure there are three feet of clearance in all directions surrounding the
antenna.
Follow the specific antenna installation instructions included with the outside antenna.
Lightning protection is recommended for all in-building installations. Take extreme care to
ensure neither you nor the antenna come in contact with any electrical power lines.
To obtain maximum performance, the antenna should point toward the cell tower. Follow
the instructions included with the outside antenna.
RF Signal
Cell Tower
Yagi Outside Antenna
NOTE: See RF Safety Warnings (p. 9)
Installing a Wilson Signal Booster
Select a location to install the Signal Booster that is away from excessive heat, direct
sunlight, moisture and that has proper ventilation. Ensure the Signal Booster is installed
within six feet of where the cellular device will be used (to accommodate the six-foot
adapter extension cable). Run the cable from the outside antenna and attach it to the
connector labeled “Outside Antenna” on the Signal Booster. Connect the power supply
(sold separately) to the power input labeled “12V DC” on the Signal Booster.
Recommended installation locations for
in-building are:
• On a wall
• On the ceiling
• Near a power outlet
7
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
In-Vehicle/In-Building
Powering up a Wilson Electronics Signal Booster
For In-Vehicle use, first connect the power
cable to the Signal Booster input marked
“12V DC” and then insert the large end into a
12V DC power socket or vehicle power outlet.
The Signal Booster may remain on all the
time; however, leaving the Signal Booster
on in a vehicle when it is not running can
discharge the battery in a day or two.
Carefully insert the power cable.
In-vehicle 12V DC power supply (included)
A good option is to power the Signal Booster
through the ignition switch so that the Signal
Booster turns off and on with the vehicle. Or
unplug the power supply. (Part# 859905
12V DC Hardwire Kit available from
www.WilsonElectronics.com).
For In-Building use, first connect the optional
AC/DC power supply to the Signal Booster
input labeled “12V DC” and then into a wall
outlet.
!
!
Warning: Verify that both the outside
antenna and the adapter extension cable
are connected to the Signal Booster
before powering up the Signal Booster.
Warning: Use only a Wilson power supply.
Use of a non-Wilson power supply could
damage your equipment, phone and/or
data card.
In-building AC/DC power supply (sold
separately)
Testing a Wilson Signal Booster
To test your Signal Booster, go to a weak signal area where your cell phone registers only
1-2 bars without the Signal Booster turned on. Then connect the Signal Booster to the
phone. You should see a signal improvement of 2 or more bars. Note: Many phones take
up to 20 seconds to reset the bar indicator.
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
8
Warnings and Recommendations
Warning:
Verify that both the outside antenna and the adapter extension cable are
connected to the Signal Booster before powering up the Signal Booster.
Warning:
RF Safety: In-Vehicle - The outside antenna must be installed with a
separation of at least 20 inches from any of the vehicle’s occupants or
nearby persons and must not be located or operating in conjunction
with any other antenna or Signal Booster. Use of a cellular Signal
Booster with an antenna gain higher than 6.12 dBi is in violation of
FCC regulations, for which the offender is fully liable. All Wilson mobile
antennas are 6.12 dBi or less.
Warning:
RF Safety: In-Vehicle - All roof-mount antennas should be centrally
located on the roof of the vehicle. Glass-mount antennas should be
located in the middle of either the front or back windshield. Mirror-mount
antennas should be at least 20 inches from any persons in or around the
vehicle.
Warning:
RF Safety: In-Building - The outside antenna must be installed on an
outdoor structure with a separation of at least 26 inches from all persons
during normal operation. The outside building antenna must not have a
gain that exceeds 15 dBi. All Wilson outside building antennas have gains
of 15 dBi or less.
Warning:
Do not plug in the power supply until the Outside Antenna and external
adapter cables are attached to the Signal Booster.
Lightning protection is recommended for all in-building installations.
NOTE: The aluminum casing of a Wilson Signal Booster will adjust very quickly to the
ambient temperature of its environment. For example, in the summer, when the inside
of a car can reach 140 degrees Fahrenheit, the Signal Booster temperature may be 150
degrees or higher. The casing will be hot to the touch, similar to a metal door handle or a
steering wheel. Such high temperatures will not damage the Signal Booster, nor do they
pose a fire risk to the vehicle. As recommended in these instructions, install the Signal
Booster in a location with adequate ventilation, such as under the seat, in the trunk or under
the dashboard. Keep the area free of items that could block air flow to the Signal Booster.
9
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics’ 30-day
money-back guarantee. If for any reason the performance of any product is not
acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
1-Year Warranty
Wilson Electronics signal boosters are warranted for one (1) year against defects
in workmanship and/or materials. Warranty cases may be resolved by returning
the product directly to the reseller with a dated proof of purchase.
Signal boosters may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its
option, either repair or replace the product. Wilson Electronics will pay for delivery
of the repaired or replaced product back to the original consumer, if located within
the continental U.S.
This warranty does not apply to any signal boosters determined by Wilson
Electronics to have been subjected to misuse, abuse, neglect, or mishandling that
alters or damages physical or electronic properties.
RMA numbers may be obtained by phoning
our free U.S. based Technical Support at (507)282-8484.
The Manufacturer’s rated output power of this equipment is for single carrier operation.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of this device.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
One or more of the following U.S. Patent numbers may apply to the Signal Booster in this
product – D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186;
7,783,318; 7,684,838; 12,714,994.
Contact Wilson Electronics Tech Support with any questions at (507)282-8484
Or email: [email protected] Hours: 7am to 6pm MST.
10
Signal Booster Specifications
Dual-Band
800/1900 MHz Specifications
Model Number / Part Number
Connectors
Impedance (input/output)
Dimensions
Weight
Frequency
1
Passband Gain (nominal)
2B1401 / 811207, 811209
FME-Male
50 ohms
5 x 5.4 x 1.4 inch or 14 x 10.8 x 3.5 cm
1.32 lbs or 0.6 kg
824-894 MHz / 1850-1990 MHz / GSM 1575 MHz
800 MHz and 1900 MHz
1575 MHz
2
3
20 dB
8 dB
20 dB Bandwidth (nominal)
800 MHz (uplink/downlink)
1900 MHz (uplink/downlink)
Power output for single cell phone (uplink)
CDMA
GSM
EDGE
WCDMA
Power output for single received channel
(downlink)
3
800 MHz
33 dBm
32.6 dBm
33.1 dBm
33.5 dBm
800 MHz
CDMA
GSM
EDGE
AMPS
GPS
Power output for multiple received
channels (downlink). The maximum
power is reduced by the number of
channels:
50 MHz / 49 MHz
121 MHz / 94 MHz
1900 MHz
29.6 dBm
27.3 dBm
27.8 dBm
29.7 dBm
1575 MHz
9.7 dBm
8.7 dBm
9.1 dBm
10.3 dBm
1900 MHz
13.6 dBm
9.6 dBm
12.3 dBm
11.9 dBm
18 dBm
4
Noise Figure (typical)
Isolation
Power Requirements
Signal Booster Usage
Maximum Power
Number of
channels
2
3
4
5
6
800 MHz
1900 MHz
10.1 dBm
6.5 dBm
4.0 dBm
2.1 dBm
0.5 dBm
10.9 dBm
7.4 dBm
4.9 dBm
2.9 dBm
1.4 dBm
3 dB nominal
> 90 dB
12 V, .5 A - 1.5 A (subject to uplink power)
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is
20 dB lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple
carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is reradiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or
gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: (507)282-8484
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
Part #110930 AIG - FRENCH 001 070111
2B1401 / 811207, 811209
FME-Male
50 ohms
5 x 5.4 x 1.4 inch or 14 x 10.8 x 3.5 cm
1.32 lbs or 0.6 kg
824-894 MHz / 1850-1990 MHz / GSM 1575 MHz
800 MHz and 1900 MHz
1575 MHz
20 dB
8 dB
2Bande passante de 20 dB (nominale)
3
50 MHz / 49 MHz
121 MHz / 94 MHz
800 MHz
1900 MHz
29.6 dBm
27.3 dBm
27.8 dBm
29.7 dBm
33 dBm
32.6 dBm
33.1 dBm
33.5 dBm
800 MHz
1575 MHz
1900 MHz
9.7 dBm
8.7 dBm
9.1 dBm
10.3 dBm
13.6 dBm
9.6 dBm
12.3 dBm
11.9 dBm
18 dBm
Maximum Power
800 MHz
1900 MHz
10.1 dBm
6.5 dBm
4.0 dBm
2.1 dBm
0.5 dBm
10.9 dBm
7.4 dBm
4.9 dBm
2.9 dBm
1.4 dBm
3 dB nominal
> 90 dB
12 V, .5 A - 1.5 A (subject to uplink power)
3301 East Deseret Drive, St. George, UT 84790
Pour le service de Soutien technique, visitez www.WilsonElectronics.com
ou envoyez un email à [email protected]
Téléphone: 866-294-1660 Local: 435-673-5021 Télécopieur: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
Part #110930 AIG - FRENCH 001 070111
10
Avertissement:
Avertissement:
Avertissement:
Avertissement:
Avertissement:
9
8
Station de base
Signal RF
7
952330
952320
951104
952400
951103
952375
951102
952350
951101
952302
951110
Figure 1
5
6
!
Appareil
sans fil
Bloc d’alimentation c.c.
4
3
2
1
Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed