Hinkley Lighting 4811KZ Installation manual

Hinkley Lighting 4811KZ is a lighting fixture designed to be mounted on a ceiling. It comes with a variety of stem lengths, allowing you to customize the height of the fixture to your liking. The fixture can be mounted either close to the ceiling or with a longer stem for a more dramatic look. The canopy of the fixture can be secured to the stem using a hex nut. The fixture also comes with ball knobs that can be used to secure the fixture to the ceiling.

PDF

Document

HINKLEY
L
I
G
H
T
I
N
Item No. 4811
G
 start here
Drawing 1 - Fixture Assembly
L
H
wire
P
C
Assembly Instructions
English
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
stem
Spanish
Safety Warning: read wiring and grounding instructions (I.S. 18) and any
wire
Instrucciones De montaje
Num&eacute; ro d’artic le: 4811
 commencez ici
French
requirements.
1. Shut off electrical current before starting. If the fixture you are
replacing is turned on and off by a wall switch, simply turn the switch
off. If not, remove the appropriate fuse (or open the circuit breakers)
until the fixture is dead.• DO NOT restore current - either by fuse,
breaker or switch - until the new fixture is completely wired in place.
stem
wire
1. Determine the desired length of the chandelier.
2. The fixture is supplied with a variety of stem lengths. Determine
what combination of stems are needed to achieve desired length - see
Drawing 1.
3. Slip stems over wire and thread first stem onto top of chandelier.
Repeat this process until all required stems are threaded together.
4. Slip wire through center hole of canopy (C) and canopy plate (P).
Then slip lock washer (L) over threaded tube from stem and thread on
hex nut (H), thighten to secure canopy to stem.
5. NOTE: To mount fixture CLOSE TO CEILING use the 4” stem
supplied only. Do Not mount top of fixture directly to the canopy.
Drawing 2 - Fixture Mounting
junction box
2
1. Thread two long 8-32 (1) screws provided into the mounting strap
(2).
• NOTE: the tow screws should be threaded into the gull wing shaped
part of the mounting strap with the flat part of the strap facing up.
• Make sure screws are threaded into holes that line up with holes in
the canopy (3) - see Drawing 2.
2. Attach mount strap (2) to junction box with two short 8-32 screws (5)
not provided.
3. Make wire connections following the instructions on I.S.18 instruction
sheet provided.
4. Slip canopy/fixture over screws (1) and secure fixture to ceiling using
with ball knobs (4).
1
5
2
3
2
4
Drawing 3 - Loop adjustments
A
0
90
B
1. For final adjustments to the fixture after installation, make sure
interior loop (C) is parallel to loop (A), and loop (B) is 90 degrees to
loop (A) and (C) - see Drawing 3.
NOTE: loops can be rotate without the use of tools.
C
HINKLEY LIGHTING
33000 Pin Oak Parkway Avon Lake, OH 44012
800.446.5539 / 440.653.5500
hinkleylighting.com
I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING
INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS.
TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW
WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR
LOCAL AUTHORITIES FOR CODE REQUIREMENTS
Drawing 1 – Flush Mount
ADVERTENCIA DE SEGURIDAD: LEA LAS INSTRUCCIONES DE CABLEADO
Y LA TIERRA (IS 18), E INSTRUCCIONES ADICIONALES. APAUGE LA
ALIMENTACI&Oacute;N DE CORRIENTE DURANTE LA INSTALACI&Oacute;N. SI SE
REQUIERE NUEVO CABLEADO, CONSULTE CON UN ELECTRICISTA O
AUTHORIDADES LOCALES PARA REQUISITOS DEL C&Oacute;DIGO
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth,
2. Connect negative supply wire (C) (typically white or the ribbed, marked
3. Please refer to the grounding instructions below to complete all
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth
2. Connect negative supply wire (C) (typically white or the ribbed, marked
3. Cover open end of connectors with silicone sealant to form a
side of the two-conductor cord) to negative fixture lead (D).
electrical connections
unmarked side of the two-conductor cord) to positive fixture lead (B)
with appropriately sized twist on connector --- see Drawings 2 or 3.
side of the two-conductor cord) to negative fixture lead (D).
watertight seal.
un sello herm&eacute;tico.
If installing a wall mount fixture, use caulk to seal gaps between the
fixture mounting plate (backplate) and the wall. This will help prevent
water from entering the outlet box. If the wall surface is lap siding, use
caulk and a fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all
grounding instructions
Flush Mount Fixtures
Drawing 3 – Post-Mount
AVERTISSEMENT DE SECURITE: LIRE CABLAGE ET INSTRUCTIONS DE
MISE (IS 18), ET TOUTE AUTRE INSTRUCTION. COUPER L’ALIMENTATION
ELECTRIQUE PENDANT L’ONSTALLATION. SI DE NOUVELLES CABLAGE
N’EST NECESSAIRE, CONSULTEZ UN ELECTRICIEN QUALIFIE OU
AUTORITES LOCALES POUR EXIGENCES DU CODE.
wiring instructions
unmarked side of the two-conductor cord) to positive fixture lead (B)
with appropriately sized twist on connector - see Drawings 1 or 2.
Drawing 2 – Chain Hung
For positive grounding in a 3-wire electrical system, fasten the fixture
ground wire (E) (typically copper or green plastic coated) to the fixture
mounting strap (M) with the ground screw (S) - see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting
screws in strap. Any remaining tapped hole may be used for the ground screw.
Loop fixture ground wire (E) (typically copper or green plastic coated)
under the head of the ground screw (S) on fixture mounting strap (M)
and connect to the loose end of the fixture ground wire directly to the
ground wire of the building system with appropriately sized twist-on
connectors - see Drawing 2.
Post-Mount Fixtures
Accesorios Posterior Monte
Chain Hung Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated)
to power supply ground with appropriately sized twist-on connector
inside post. Cover open end of connector with silicone sealant to form a
watertight seal - see Drawing 3.
HINKLEY LIGHTING
33000 Pin Oak Parkway Avon Lake, OH 44012
800.446.5539 / 440.653.5500
hinkleylighting.com">

Hello! I am an AI chatbot specifically trained to assist you with the Hinkley Lighting 4811KZ Installation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

It looks like you''ve reached a document that is written in multiple languages, including one that isn''t your native language. You can use the following links to temporarily hide pages without the language you prefer.