Alpine MRD-M1005 Car Stereo System User Manual

Alpine MRD-M1005 Car Stereo System User Manual
English
R
MRD-M1005/MRD-M605
MONO POWER AMPLIFIER
• OWNER'S MANUAL
Please read this manual to maximize your enjoyment of the outstanding
performance and feature capabilities of the equipment, then retain the
manual for future reference.
• MODE D'EMPLOI
Veuillez lire ce mode d'emploi pour tirer pleinement profit des
excellentes performances et fonctions de cet appareil, et conservez-le
pour toute référence future.
• MANUAL DE OPERACION
Lea este manual, por favor, para disfrutar al máximo de las
excepcionales prestaciones y posibilidades funcionales que ofrece el
equipo, luego guarde el manual para usarlo como referencia en el futuro.
Français
English
CONTENTS
TABLE DES MATIERES
INDICE
WARNING ............................................................... 2
CAUTION ................................................................ 3
CONNECTIONS OF POWER SUPPLY TERMINAL ........ 4
INSTALLATION ....................................................... 5
CONNECTIONS ....................................................... 6
HOW TO REMOVE OR ATTACH THE TOP COVER ..... 9
SWITCH SETTINGS .............................................. 10
OPERATION METHOD .......................................... 11
IN CASE OF DIFFICULTY ....................................... 14
SYSTEMS ............................................................. 15
SPECIFICATIONS .................................................. 17
AVERTISSEMENT ...................................................... 2
ATTENTION ................................................................ 3
CONNEXIONS DE LA BORNE D’ALIMENTATION ........ 4
INSTALLATION .......................................................... 5
CONNEXIONS ............................................................ 6
COMMENT RETIRER OU FIXER LE COUVERCLE
SUPERIEUR ............................................................... 9
REGLAGES DE COMMUTATEUR .............................. 10
METHODE DE FONCTIONNEMENT ................................ 11
EN CAS DE PROBLEME ........................................... 14
SYSTEMES .............................................................. 15
SPECIFICATIONS ..................................................... 17
ADVERTENCIA ........................................................ 2
PRUDENCIA ........................................................... 3
CONEXIONES DEL TERMINAL DE ALIMENTACIÓN .... 4
INSTALACION ......................................................... 5
CONEXIONES ......................................................... 6
CÓMO DESINSTALAR O INSTALAR LA CUBIERTA
SUPERIOR .............................................................. 9
AJUSTES DEL INTERRUPTOR .............................. 10
MÉTODO DE OPERACIÓN ..................................... 11
EN CASO DE DIFICULTAD ..................................... 14
SISTEMAS ............................................................ 15
ESPECIFICACIONES ............................................. 17
ACCESSORIES
ACCESSOIRES
ACCESORIOS
• Hexagon Wrench ......................................... 1 SET
• Self-Tapping Screw ............................................ 4
• Llave hexagonal ...................................... 1 JUEGO
• Tornillo autorroscante ........................................ 4
ALPINE ELECTRONICS MARKETING, INC.
1-1-8 Nishi Gotanda,
Shinagawa-ku, Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Phone 03-9769-0000
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS GmbH
Frankfurter Ring 117, 80807 München,
Germany
Phone 089-32 42 640
ALPINE ELECTRONICS OF CANADA, INC.
7300 Warden Ave., Suite 203, Markham,
Ontario L3R 9Z6, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway,
Coventry CV4 9TW, U.K.
Phone 0870-33 33 763
Kukje Printing Co., Ltd
127-2 Gamjeon-dong
Sasang-gu
Busan Korea
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava) - APDO 133, Spain
Phone 945-283588
Designed by ALPINE Japan
Printed in Korea (S)
1
68-02278Z44-A
English
Introduction:
Introduction:
Please read this OWNER'S MANUAL thoroughly to
familiarize yourself with each control and function. We
at ALPINE hope that your new MRD-M1005/MRDM605 will give you many years of listening enjoyment.
In case of problems when installing your MRDM1005/MRD-M605, please contact your authorized
ALPINE dealer.
CAUTION: These controls are for tuning your system.
Please consult your authorized Dealer for adjustment.
This symbol means important
instructions.
WARNING Failure to heed them can result in
serious injury or death.
This symbol means important
instructions.
CAUTION Failure to heed them can result in
injury or property damages.
WARNING
AVERTISSEMENT
ADVERTENCIA
DO NOT OPERATE ANY FUNCTION THAT TAKES
YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE. Any function that requires your
prolonged attention should only be performed after
coming to a complete stop. Always stop the vehicle in
a safe location before performing these functions.
Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN
STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
DO NOT DISASSEMBLE OR ALTER. Doing so may
result in an accident, fire or electric shock.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application
may result in fire, electric shock or other injury.
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES. Failure to do so may result in
fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may
result in fire.
MAKE THE CORRECT CONNECTIONS. Failure to make
the proper connections may result in fire or
product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND. (Check with your dealer if you are not
sure.) Failure to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL. Failure to do so
may result in electric shock or injury due to electrical
shorts.
2
English
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS. Arrange wiring and cables
in compliance with the manual to prevent obstructions
when driving. Cables or wiring that obstruct or hang
up on places such as the steering wheel, gear lever,
brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never
cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES. When drilling holes in the chassis for
installation, take precautions so as not to contact,
damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may
result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering
systems (or any other safety-related system), or tanks
should NEVER be used for installations or ground
connections. Using such parts could disable control of
the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS
OUT OF THE REACH OF CHILDREN. Swallowing them
may result in serious injury. If swallowed, consult a
physician immediately.
CAUTION
ATTENTION
PRUDENCIA
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage
to the product. Return it to your authorized Alpine
dealer or the nearest Alpine Service Center for
repairing.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS. The wiring and installation of this unit
requires special technical skill and experience. To
ensure safety, always contact the dealer where you
purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY. Be sure to use only the specified
accessory parts. Use of other than designated parts
may damage this unit internally or may not securely
install the unit in place. This may cause parts to
become loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE. Route the
cables and wiring away from moving parts (like the
seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to
prevent the wire’s insulation from being cut by the
metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST. Avoid installing the unit in
locations with high incidence of moisture or dust.
Moisture or dust that penetrates into this unit may
result in product failure.
3
English
CAUTION
ATTENTION
PRUDENCIA
CONNECTIONS OF POWER
SUPPLY TERMINAL
CONNEXIONS DE LA BORNE
D’ALIMENTATION
CONEXIONES DEL TERMINAL
DE ALIMENTACIÓN
● Before connecting the power supply wire to the
unit, be sure to remove the negative (–) terminal of
the vehicle’s battery.
• Make the power supply wire connection to the
battery positive (+) terminal of the unit, before
connecting the wire to the positive (+) terminal
of the vehicle’s battery .
● When connecting the power supply wire to the
unit, be sure not to short the wire.
• If you tighten the screw to fix the power supply
wire on the unit after the power supply
connection is completed, the tool may touch the
unit and may cause a short-circuit.
• Be sure not to allow the power supply wire to
be exposed outside the terminal.
• Fix the power supply wire securely to prevent
disconnection or dropping.
Fig. 1
Connected Battery/
Batterie Reliée/
Batería Conectada
● When tightening the screw to fix the power supply
wire, be sure not to touch the tool to the unit.
4
Fig. 2
Connected Battery/
Batterie Reliée/
Batería Conectada
Fig. 3
English
INSTALLATION
INSTALLATION
INSTALACION
Due to the high power output of the MRD-M1005/
MRD-M605, considerable heat is produced when the
amplifier is in operation. For this reason, the amplifier
should be mounted in a location which will allow for
free circulation of air, such as inside the trunk. For
alternate installation locations, please contact your
authorized Alpine dealer.
1. Using the amplifier as a template, mark the four
screw locations.
2. Make sure there are no objects behind the surface
that may become damaged during drilling.
3. Drill the screw holes.
4. Position the MRD-M1005/MRD-M605 over the
screw holes, and secure with four self-tapping
screws.
NOTE:
To securely connect the ground lead, use an already
installed screw on the metal part of the vehicle
(marked (★)). Be sure this is a good ground by
checking continuity to the battery (–) terminal. As
much as possible connect all equipment to the same
ground point. These procedures will help eliminate
noise.
1 Self-Tapping Screws (M4 x 20)
2 Ground Lead
3 Chassis
4 Holes
1
2
★
3
4
Fig. 4
5
English
MRD-M1005
1
2
3
4
5
6
7
Fig. 5
MRD-M605
1
2
3
4
5
6
7
CONNECTIONS
Fig. 6
CONNEXIONS
CONEXIONES
Before making connections, be sure to turn the power
off to all audio components. Connect the yellow
battery lead from the amp directly to the positive (+)
terminal of the vehicle's battery. Do not connect this
lead to the fuse block.
To prevent external noise from entering the audio
system.
• Locate the unit and route the leads at least 10 cm
away from the car harness.
• Keep the battery power leads as far away from
other leads as possible.
• Connect the ground lead securely to a bare metal
spot (remove any paint or grease if necessary) of
the car chassis.
• If you add an optional noise suppressor, connect it
as far away from the unit as possible. Your Alpine
dealer carries various noise suppressors, contact
them for further information.
• Your Alpine dealer knows best about noise prevention
measures so consult your dealer for further information.
6
English
1 Speaker Output Terminals
The MRD-M1005/MRD-M605 has one set of
speaker outputs. Be sure to observe correct
speaker output connections and phasing. Connect
the positive output to the positive speaker terminal
and the negative to negative.
Do not connect the Speaker-Minus-Lead to the
vehicle’s chassis.
NOTE:
Do not connect speaker leads together or to
chassis ground.
2 Amplifier LINK Connector
3 RCA Input Jacks
Connect these jacks to the line out leads on your
head unit using RCA extension cables (sold
separately).
4 Pre-Out Jacks
5 Battery Lead (Sold Separately)
Be sure to add a fuse as close as possible to the
battery’s positive (+) terminal. This fuse will
protect your vehicle’s electrical system in case of a
short circuit. If you need to extend this lead, the
wire gauge should be AWG8 or larger.
6 Remote Turn-On Lead (Blue/White, Sold
Separately)
Connect this lead to the remote turn-on or power
antenna (positive trigger, (+) 12V only) lead of
your head unit.
7 Ground Lead (Sold Separately)
Connect this lead securely to a clean, bare metal
spot on the vehicle chassis. Verify this point to be
a true ground by checking for continuity between
that point and the negative (–) terminal of the
vehicle's battery. Ground all your audio components to the same point on the chassis to prevent
ground loops.
7
English
Fig. 7
Hexagon screw/Vis à six pans/Tornillo hexagonal
Lead/Conducteur/Alambre
Lead Terminal/Borne de conducteur/Terminal del conductor
Fig. 8
Cautions on wire lead connections
When using third-party wire cables (power supply
wire), use the supplied hex screws and the hex
wrench (included) to simplify the connection.
Refer to the description below for the proper
procedure.
If you are in doubt about how to make this connection, consult your dealer.
1. Check the wire size.
Notes:
• Wire Size (Battery Lead, Ground Lead)
Recommended wire size for this unit is AWG4 –
AWG8.
• If the wire gauge used is unknown, ask your
dealer.
2. Remove the insulation from the ends of the wire
leads by about 7 – 10mm (9/32" – 3/8"). (Fig. 7)
Notes:
• If length of the exposed wire is too short, a poor
connection may occur causing operation failure
or sound interruption.
• On the other hand, if the length is too long, an
electrical short-circuit may occur.
3. Turn the screw attached to the terminal. Insert the
exposed wire end into the lead terminal. Tighten the
hexagon screw with the hex wrench (included), to
fix the lead. (Fig. 8)
Before making this connection, use insulated
shrink tubing to cover any exposed wire
extending beyond the terminal.
Notes:
• Use only the hexagon screws included.
• For safety reasons, connect the battery leads
last.
• To prevent disconnection of the leads or
dropping of the unit, do not use the cabling to
carry the unit.
8
English
HOW TO REMOVE OR ATTACH
THE TOP COVER
COMMENT RETIRER OU FIXER LE
COUVERCLE SUPERIEUR
CÓMO DESINSTALAR O INSTALAR
LA CUBIERTA SUPERIOR
• There are adjustment switches and buttons under the top
cover.
• When adjusting, remove the top cover. After adjusting, it is
necessary to reattach the top cover to its former position.
• Perform the operation by referring to the following
procedure.
1. To remove the top cover
1) Using the hexagonal wrench (M3), remove the two
hexagonal screws
holding top cover
in place.
2
1
2
1
1
2
1
2
Fig. 9
2) While raising gently, remove the top cover.
3
2. To attach the top cover
1) Line up the two raised projections
on the top cover
with the depressions on the main body.
3
3
1
3
Fig. 10
1 1
2) Gently lower the top cover .
3) Attach the top cover
with the two hexagonal screws
.
2
1
1
2
1
1
2
1
2
Fig. 11
* Tighten the screws securely so that they do not
come loose due to vibrations while the vehicle is
moving.
NOTES:
• Be sure to fasten the cover securely. Failure to do so may
lead to a malfunction.
• The warranty is invalidated if the unit is used with the
cover open.
9
English
8
9
10
★
★
SWITCH SETTINGS
REGLAGES DE COMMUTATEUR
AJUSTES DEL INTERRUPTOR
8 Crossover Frequency Adjustment Knob
Permits adjustment of the crossover frequency, by
rotating the knob to select any frequency between
30 to 200 Hz as the crossover point.
9 Lowpass Filter Slope Selector Switch
The Lowpass Filter slope can be set for either
12dB/oct. or 24dB/oct..
10 Subsonic Mode Selector Switch
a) Set this switch to “OFF” when you
want to hear tones not possible when
the Subsonic filter switch is used.
b) Set to “15 Hz” when connected to
subwoofers such as 10 inch (25 cm)
bass speakers, if the sound seems
less distorted at that setting.
c) Set to “30 Hz” when connected to
ordinary speakers (not subwoofers)
for instance a mid bass speaker of 8
inches (20 cm) or more if the sound
seems less distorted at that setting.
10
English
16
19 18 17
★
★
16 Display
16 Affichage
17 UP
17 Touche UP
18 Touche
18 Botón
18
Button
DN (DOWN) Button
19 MODE Button
DN (DOWN)
19 Touche MODE
DN (DOWN)
OPERATION METHOD
METHODE DE FONCTIONNEMENT
MÉTODO DE OPERACIÓN
SELECTING THE AMP ID
• When multiple amplifiers are connected to an
Amplifier LINK compatible Head Unit, each amp
must have its own, unique ID.
• With a single amplifier system, an AMP ID is not
necessary.
1. Press the MODE button until “ID” is displayed.
2. Select the AMP ID by pressing the
button.
DN/UP
11
English
ADJUSTING THE INPUT LEVEL
• Adjust the input level of the amplifier to match
the output of the connected head unit.
1. Press the MODE button until “GAIN” is
displayed.
2. Press the DN/UP button to adjust the input
level.
Adjustment range: 0.1V – 8V
BASS EQ ADJUSTMENT
• The output can be modified using a fixed, single
band EQ at 45 Hz.
Set this EQ to a level that sounds best to you.
Normally it is adequate set at 0dB, but if you feel
that the low frequency output is inadequate, then
set it to a level that you like.
1. Press the MODE button until “B.EQ” is
displayed.
2. Press the DN/UP button to adjust the BASS
EQ level.
Adjustment range: 0 dB – +16 dB
12
English
TO DISPLAY THE CROSSOVER FREQUENCY
• The Crossover Frequency, previously set with
the Crossover Frequency Adjustment Knob, can
be displayed.
1. Press the MODE button until “Hz” is displayed.
The Crossover Frequency is displayed.
TO DISPLAY THE SUBSONIC FILTER
• The frequency set with the Subsonic Mode
Selector Switch can be displayed.
1. Press the MODE button until [Hz] is displayed.
2. Press the MODE button one more time.
<Display example>
HOW TO CHANGE THE DISPLAY
• Voltage and temperature can be displayed.
1. Press the MODE button until “V” “°C” or “°F” is
displayed.
2. Press the DN/UP
display mode.
Voltage
(V)
Temperature
(Celsius, °C)
button to select the
Temperature
(Fahrenheit, °F)
*
SCAN
*SCAN:
Voltage, temperature (Celsius) and temperature
(Fahrenheit) values are displayed for 5 seconds
each and then repeated in a loop.
2. Appuyez sur la touche DN/UP
select the display mode.
Tension
(V)
button to
Température
(Fahrenheit, °F)
*
SCAN
Temperatura
(Celsius, °C)
Temperatura
(Fahrenheit, °F)
*
SCAN
13
English
IN CASE OF DIFFICULTY
EN CAS DE PROBLEME
EN CASO DE DIFICULTAD
If you encounter a problem, please review the items in
the following checklist. This guide will help you isolate
the problem if the unit is at fault. Otherwise, make
sure the rest of your system is properly connected or
consult your authorized Alpine dealer.
● Volume is low.
• Input level from the head unit with which the
amplifier is being used is low.
• Increase the volume on the head unit.
Indication
HOT
TEM
VLT
CUR
14
Cause and Solution
• The protection circuit is
activated due to high
temperature. The amplifier
output becomes disabled.
• The indicator will disappear
when the temperature returns
to within operation range.
• The amplifier has been
shutdown due to excessive
heat.
The amplifier is automatically
reset.
• The indicator will disappear
when the temperature returns
to within operation range. The
amplifier is automatically
reset.
• The amplifier has been
shutdown due to excessive
voltage.
• Lower the power supply
voltage to an appropriate level.
Turn off the power once, then
turn on the power again. The
indicator will disappear and
the amplifier will return to the
normal operation.
• The amplifier has been shutdown due to excessive
current.
• Find and eliminate the cause
of the excessive current, then
turn the power off.
Indication
HOT
TEM
VLT
CUR
HOT
TEM
VLT
CUR
SYSTEMS/SYSTEMES/SISTEMAS
English
5
18
7
–
+
MRD-M605
(L)
(R)
16
(L)
(R)
6
17
18
18
5
7
–
+
MRD-M1005
5
MRD-M1005
(L)
–
+
18
(R)
–
+
(L)
7
–
+
16
(R)
18
16
(L)
(R)
6
17
6
[English]
16 RCA Extension Cable (Sold Separately)
17 Head Unit etc.
18 Subwoofer
15
English
5
18
+
–
MRD-M1005
(L)
26
7
(R)
16
(L)
(R)
6
24
[English]
24 Amplifier LINK compatible head unit
25 Amplifier LINK Connector
26 Amplifier LINK box (KCE-511M, Sold Separately)
16
English
SPECIFICATIONS
SPECIFICATIONS
Power Output: RMS Continuous Power (at 14.4V, 20Hz to 200Hz)
Per channel into 4 ohms (≤1% THD+N) ... MRD-M1005: 700Wx1
MRD-M605: 400Wx1
Per channel into 2 ohms (≤1% THD+N) ... MRD-M1005: 1,000Wx1
MRD-M605: 600Wx1
Frequency Response .............................................. 20 Hz to 200 Hz
Signal-to-Noise Ratio
(Reference: 1watt into 4ohms) ............................................ 90 dBA
(CEA2006) ........................................................................... 65 dBA
Input Sensitivity (for rated power output) ................... 0.1V to 8.0V
Input Impedance .............................................. Line in: 10k ohms<
Speaker Impedance ..................................................... 4 or 2 ohms
Low Pass Filter ......................... 30 Hz to 200 Hz (12dB/24dB /oct.)
Subsonic Filter ..................................... OFF/15Hz/30Hz (24dB/oct.)
Bass EQ ............................................................................... +16 dB
Power Requirement ......................... 11 – 16V DC Negative Ground
Dimensions (W x H x D)
MRD-M1005 ................................... 360mm x 60mm x 228mm
MRD-M605 ..................................... 290mm x 60mm x 228mm
Weight
MRD-M1005 .................................................................. 4.85 kg
MRD-M605 ...................................................................... 3.6 kg
NOTE:
For product improvement, specifications and design are subject to
change without notice.
SERVICE CARE
SOINS PRATIQUES
IMPORTANT NOTICE
This Amplifier has been type tested and found to
comply with the limits for a Class B computing device
in accordance with the specifications in Subpart J of
Part 15 of FCC Rules. This equipment generates and
uses radio frequency energy, and it must be installed
and used properly in accordance with the manufacturer's instructions.
SERIAL NUMBER:
NUMERO DE SERIE:
NUMERO DE SERIE:
INSTALLATION DATE:
DATE D'INSTALLATION:
FECHA DE INSTALACION:
INSTALLATION TECHNICIAN:
INSTALLATEUR:
TECNICO:
PLACE OF PURCHASE:
LIEU D'ACHAT:
LUGAR DE ADQUISICION:
IMPORTANT
Please record the serial number of your unit in the
space provided here and keep it as a permanent
record. The serial number plate is located on the
rear of the unit.
17
R
[PERSONNES PROTÉGÉES PAR LA GARANTIE
[LIMITATION DES GARANTIES TACITES
LA DURÉE DE TOUTES LES GARANTIES TACITES, Y
COMPRIS LA GARANTIE D'ADAPTATION À L'UTILISATION
ET LA GARANTIE DE QUALITÉ LOYALE ET MARCHANDE,
EST LIMITÉE À CELLE DE LA GARANTIE EXPRESSE
DÉTERMINÉE CI-DESSUS. PERSONNE N'EST AUTORISÉ
À ENGAGER AUTREMENT LA RESPONSABILITÉ D'ALPINE
EN VERTU DE LA VENTE D'UN PRODUIT.
[DURÉE DE LA GARANTIE
[EXCLUSIONS DE LA GARANTIE
ALPINE STIPULE EXPRESSÉMENT QU'ELLE N'EST PAS
RESPONSABLE DES DOMMAGES-INTÉRÊTS ET
DOMMAGES INDIRECTS PROVOQUÉS PAR LE PRODUIT.
LES DOMMAGES-INTÉRÊTS SONT LES FRAIS DE
TRANSPORT DU PRODUIT VERS UN CENTRE DE
SERVICE ALPINE, LA PERTE DE TEMPS DE L'ACHETEUR
ORIGINAL, LA PERTE D'UTILISATION DU PRODUIT, LES
BILLETS D'AUTOBUS, LA LOCATION DE VOITURES ET
TOUS LES AUTRES FRAIS LIÉS À LA GARDE DU
PRODUIT.
LES DOMMAGES INDIRECTS SONT LES FRAIS DE
RÉPARATION OU DE REMPLACEMENT D'AUTRES BIENS
ENDOMMAGÉS SUITE AU MAUVAIS FONCTIONNEMENT
DU PRODUIT.
LES RECOURS PRÉVUS PAR LES PRÉSENTES
EXCLUENT ET REMPLACENT TOUTE AUTRE FORME DE
RECOURS.
1-800-ALPINE-1 (1-800-257-4631)
1-888-NAV-HELP (1-888-628-4357)
R
LIMITED WARRANTY
ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality
craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any
questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below.
This Warranty covers Car Audio Products and Related
Accessories ("the product"). Products purchased in the
Canada are covered only in the Canada. Products
purchased in the U.S.A. are covered only in the U.S.A.
3 You must supply proof of your purchase of the product.
4 You must package the product securely to avoid
damage during shipment. To prevent lost packages it is
recommended to use a carrier that provides a tracking
service.
[LENGTH OF WARRANTY:
[HOW WE LIMIT IMPLIED WARRANTIES:
This Warranty is in effect for one year from the date of the
first consumer purchase.
This Warranty only covers the original purchaser of the
product, who must reside in the United States, Puerto Rico
or Canada.
ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR
USE AND MERCHANTABILITY ARE LIMITED IN
DURATION TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE AND NO PERSON IS
AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT.
[WHAT IS COVERED:
[HOW WE EXCLUDE CERTAIN DAMAGES:
This Warranty covers defects in materials or workmanship
(parts and labor) in the product.
ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR
INCIDENTAL AND CONSEQUENTIAL DAMAGES
CAUSED BY THE PRODUCT. THE TERM "INCIDENTAL
DAMAGES" REFERS TO EXPENSES OF
TRANSPORTING THE PRODUCT TO THE ALPINE
SERVICE CENTER, LOSS OF THE ORIGINAL
PURCHASER'S TIME, LOSS OF THE USE OF THE
PRODUCT, BUS FARES, CAR RENTALS OR OTHERS
COSTS RELATING TO THE CARE AND CUSTODY OF
THE PRODUCT. THE TERM "CONSEQUENTIAL
DAMAGES" REFERS TO THE COST OF REPAIRING OR
REPLACING OTHER PROPERTY WHICH IS DAMAGED
WHEN THIS PRODUCT DOES NOT WORK PROPERLY.
THE REMEDIES PROVIDED UNDER THIS WARRANTY
ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.
[PRODUCTS COVERED:
[WHO IS COVERED:
[WHAT IS NOT COVERED:
This Warranty does not cover the following:
1 Damage occurring during shipment of the product to
Alpine for repair (claims must be presented to the
carrier).
2 Damage caused by accident or abuse, including burned
voice coils caused by over-driving the speaker (amplifier
level is turned up and driven into distortion or clipping).
Speaker mechanical failure (e.g. punctures, tears or
rips). Cracked or damaged LCD panels. Dropped or
damaged hard drives.
3 Damage caused by negligence, misuse, improper
operation or failure to follow instructions contained in the
Owner's manual.
4 Damage caused by act of God, including without
limitation, earthquake, fire, flood, storms or other acts of
nature.
Any cost or expense related to the removal or
reinstallation of the product.
5 Service performed by an unauthorized person, company
or association.
6 Any product which has the serial number defaced,
altered or removed.
7 Any product which has been adjusted, altered or
modified without Alpine's consent.
8 Any product not distributed by Alpine within the United
States, Puerto Rico or Canada.
9 Any product not purchased from an Authorized Alpine
Dealer.
[HOW STATE/PROVINCIAL LAW RELATES TO THE
WARRANTY:
This Warranty gives you specific legal rights, and you may
also have other rights which vary from state to state and
province to province. In addition, some states/provinces do
not allow limitations on how long an implied warranty lasts,
and some do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly,
limitations as to these matters contained herein may not
apply to you.
[IN CANADA ONLY:
This Warranty is not valid unless your Alpine car audio
product has been installed in your vehicle by an Authorized
Installation Center, and this warranty stamped upon
installation by the installation center.
[HOW TO OBTAIN WARRANTY SERVICE:
[HOW TO CONTACT CUSTOMER SERVICE:
1 You are responsible for delivery of the product to an
Authorized Alpine Service Center or Alpine for repair
and for payment of any initial shipping charges. Alpine
will, at its option, repair or replace the product with a
new or reconditioned product without charge. If the
repairs are covered by the warranty, and if the product
was shipped to an Authorized Alpine Service Center or
Alpine, Alpine will pay the return shipping charges.
2 You should provide a detailed description of the
problem(s) for which service is required.
Should the product require service, please call the following
number for your nearest Authorized Alpine Service Center.
CAR AUDIO 1-800-ALPINE-1 (1-800-257-4631)
NAVIGATION1-888-NAV-HELP (1-888-628-4357)
Or visit our website at; http://www.alpine-usa.com
ALPINE ELECTRONICS OF AMERICA, INC., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
ALPINE ELECTRONICS OF CANADA, INC., 7300 Warden Ave., Suite 203, Markham, Ontario L3R 9Z6, Canada
Do not send products to these addresses.
Call the toll free telephone number or visit the website to locate a service center.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed