advertisement
▼
Scroll to page 2
of
56
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator’s Manual Push Mower — Model 08M WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-03469 (September 10, 2007) 1 To The Owner Thank You Thank you for purchasing a Lawn Mower manufactured by MTD LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times. Failure to do so could result in personal injury or property damage. All information in this manual is relative to the most recent product information available at the time of printing. Review this manual frequently to familiarize yourself with the machine, its features and operation. Please be aware that this Operator’s Manual may cover a range of product specifications for various models. Characteristics and features discussed and/or illustrated in this manual may not be applicable to all models. MTD LLC reserves the right to change product specifications, designs and equipment without notice and without incurring obligation. This product has met the rigid safety standards of the Outdoor Power Equipment Institute and an independent testing laboratory. If you have any problems or questions concerning the machine, phone your local authorized MTD service dealer or contact us directly. MTD’s Customer Support telephone numbers, website address and mailing address can be found on this page. We want to ensure your complete satisfaction at all times. Throughout this manual, all references to right and left side of the machine are observed from the operating position The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with your machine, for more information. Table of Contents Safe Operation Practices......................................... 3 Assembly & Set-Up................................................... 8 Controls & Features.................................................11 Operation.................................................................12 Maintenance & Adjustment..................................13 Service......................................................................14 Troubleshooting......................................................15 Engine Operation....................................................16 Engine Maintenance...............................................18 Illustrated Parts List............................................... 22 Warranty................................................................. 28 Spanish.................................................................... 29 Record Product Information Model Number Before setting up and operating your new equipment, please locate the model plate on the equipment and record the information in the provided area to the right. You can locate the model plate by standing at the operator’s position and looking down at the rear of the deck. This information will be necessary, should you seek technical support via our web site, Customer Support Department, or with a local authorized service dealer. Serial Number Customer Support Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department. If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine, you can seek help from the experts. Choose from the options below: ◊ Visit us on the web at www.mtdproducts.com ◊ Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683 ◊ Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019 Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! California Proposition 65 WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm. WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. DANGER: This machine was built to be operated according to the safe operation practices in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, hands, toes and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. General Operation 1. Read this operator’s manual carefully in its entirety before attempting to assemble this machine. Read, understand, and follow all instructions on the machine and in the manuals) before operation. Keep this manual in a safe place for future and regular reference and for ordering replacement parts 6. Thoroughly inspect the area where the equipment is to be used. Remove all stones, sticks, wire, bones, toys and other foreign objects, which could be tripped over or picked up and thrown by the blade. Thrown objects can cause serious personal injury. 7. Plan your mowing pattern to avoid discharge of material toward roads, sidewalks, bystanders and the like. Also, avoid discharging material against a wall or obstruction, which may cause discharged material to ricochet back toward the operator. 2. Be completely familiar with the controls and the proper use of this machine before operating it. 3. This machine is a precision piece of power equipment, not a plaything. Therefore, exercise extreme caution at all times. This machine has been designed to perform one job: to mow grass. Do not use it for any other purpose. 8. To help avoid blade contact or a thrown object injury, stay in operator zone behind handles and keep children, bystanders, helpers and pets at least 75 feet from mower while it is in operation. Stop machine if anyone enters area. 4. Never allow children under 14 years of age to operate this machine. Children 14 and over should read and understand the instructions and safe operation practices in this manual and on the machine and should be trained and supervised by an adult. 9. Always wear safety glasses or safety goggles during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes. 5. Only responsible individuals who are familiar with these rules of safe operation should be allowed to use this machine. 10. Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. Shirts and pants that cover the arms and legs and steel-toed shoes are recommended. Never operate this machine in bare feet, sandals, slippery or lightweight (e.g. canvas) shoes. 11. Do not put hands or feet near rotating parts or under the cutting deck. Contact with blade can amputate fingers, hands, toes and feet. 12. A missing or damaged discharge cover can cause blade contact or thrown object injuries. 13. Many injuries occur as a result of the mower being pulled over the foot during a fall caused by slipping or tripping. Do not hold on to the mower if you are falling; release the handle immediately. 14. a. Step back from mower to fully extend your arms. b. Be sure you are well balanced with sure footing. c. Pull the mower back slowly, no more than half way toward you. d. Repeat these steps as needed. 15. Do not operate the mower while under the influence of alcohol or drugs. 16. Do not engage the self-propelled mechanism on machines so equipped while starting engine. 17. The blade control handle is a safety device. Never attempt to bypass its operation. Doing so makes the safety device inoperative and may result in personal injury through contact with the rotating blade. The blade control handle must operate easily in both directions and automatically return to the disengaged position when released. 18. 19. Never operate the mower in wet grass. Always be sure of your footing. A slip and fall can cause serious personal injury. If you feel you are losing your footing, release the blade control handle immediately and the blade will stop rotating within three seconds. Mow only in daylight or good artificial light. Walk, never run. 20. Stop the blade when crossing gravel drives, walks or roads. 21. If the equipment should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. 22. Shut the engine off and wait until the blade comes to a complete stop before removing the grass catcher or unclogging the chute. The cutting blade continues to rotate for a few seconds after the blade control is released. Never place any part of the body in the blade area until you are sure the blade has stopped rotating. When starting engine, pull cord slowly until resistance is felt, then pull rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. 28. If situations occur which are not covered in this manual, use care and good judgement. Contact Customer Support for assistance or the name of the nearest service dealer. Slope Operation Slopes are a major factor related to slip and fall accidents, which can result in severe injury. Operation on slopes requires extra caution. If you feel uneasy on a slope, do not mow it. For your safety, use the slope gauge included as part of this manual to measure slopes before operating this machine on a sloped or hilly area. If the slope is greater than 15 degrees, do not mow it. Do: 1. Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. 2. Watch for holes, ruts, rocks, hidden objects, or bumps which can cause you to slip or trip. Tall grass can hide obstacles. 3. Always be sure of your footing. A slip and fall can cause serious personal injury. If you feel you are losing your balance, release the blade control handle immediately and the blade will stop rotating within three (3) seconds. Do Not: 1. Do not mow near drop-offs, ditches or embankments, you could lose your footing or balance. 2. Do not mow slopes greater than 15 degrees as shown on the slope gauge. 3. Do not mow on wet grass. Unstable footing could cause slipping. Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the mower and the mowing activity. They do not understand the dangers. Never assume that children will remain where you last saw them. 1. Keep children out of the mowing area and under watchful care of a responsible adult other than the operator. 2. Be alert and turn mower off if a child enters the area. Never operate mower without proper trail shield, discharge cover, grass catcher, blade control handle or other safety protective devices in place and working. Never operate mower with damaged safety devices. Failure to do so can result in personal injury. 3. Before and while moving backwards, look behind and down for small children. 4. Use extreme care when approaching blind corners, doorways, shrubs, trees, or other objects that may obscure your vision of a child who may run into the mower. 24. Muffler and engine become hot and can cause a burn. Do not touch. 5. Keep children away from hot or running engines. They can suffer burns from a hot muffler. 25. Never attempt to make a wheel or cutting height adjustment while the engine is running. 6. 26. Only use parts and accessories made for this machine by the manufacturer. Failure to do so can result in personal injury. Never allow children under 14 years of age to operate this machine. Children 14 and over should read and understand the instructions and safe operation practices in this manual and on the machine and be trained and supervised by an adult. 23. Never pull the mower back toward you while you are walking. If you must back the mower away from a wall or obstruction first look down and behind to avoid tripping and then follow these steps: 27. Section 2 — Important Safe Operation Practices Service 3. Check the blade and engine mounting bolts at frequent intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn) Replace blade with the original equipment manufacture’s (O.E.M.) blade only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” 4. Mower blades are sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing them. Safe Handling Of Gasoline: 1. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately. 2. Use only an approved gasoline container. 5. 3. Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. 6. Never tamper with safety devices. Check their proper operation regularly. 4. Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle. 7. After striking a foreign object, stop the engine, disconnect the spark plug wire and ground against the engine. Thoroughly inspect the mower for any damage. Repair the damage before starting and operating the mower. 5. Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. 8. Never attempt to make a wheel or cutting height adjustment while the engine is running. 9. 6. Extinguish all cigarettes, cigars, pipes and other sources of ignition. 7. Never fuel machine indoors because flammable vapors will accumulate in the area. 8. Never remove gas cap or add fuel while engine is hot or running. Allow engine to cool at least two minutes before refueling. Grass catcher components, discharge cover, and trail shield are subject to wear and damage which could expose moving parts or allow objects to be thrown. For safety protection, frequently check components and replace immediately with original equipment manufacturer’s (O.E.M.) parts only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” 9. Never over fill fuel tank. Fill tank to no more than 1 inch below bottom of filler neck to provide for fuel expansion. 10. 10. Replace gasoline cap and tighten securely. Do not change the engine’s governor setting or over-speed the engine. The governor controls the maximum safe operating speed of the engine. 11. If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting engine. 11. Check fuel line, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. 12. Do not crank engine with spark plug removed. 12. Never store the machine or fuel container near an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. 13. Maintain or replace safety and instruction labels, as necessary. 14. 13. To reduce fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris. Observe proper disposal laws and regulations. Improper disposal of fluids and materials can harm the environment. 14. Allow machine to cool at least 5 minutes before storing. General Service: 1. 2. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Before cleaning, repairing, or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire and ground against the engine to prevent unintended starting. Do not modify engine To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor. Notice Regarding Emissions Engines which are certified to comply with California and federal EPA emission regulations for SORE (Small Off Road Equipment) are certified to operate on regular unleaded gasoline, and may include the following emission control systems: Engine Modification (EM) and Three Way Catalyst (TWC) if so equipped. Section 2 — Important Safe Operation Practices Spark Arrestor Average Useful Life Warning: This machine is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. According to the Consumer Products Safety Commission (CPSC) and the U.S. Environmental Protection Agency (EPA), this product has an Average Useful Life of seven (7) years, or 140 hours of operation. At the end of the Average Useful Life, buy a new machine or have the machine inspected annually by an authorized service dealer to ensure that all mechanical and safety systems are working properly and not worn excessively. Failure to do so can result in accidents, injuries or death. warning: Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. SAVE THESE INSTRUCTIONS! Section 2 — Important Safe Operation Practices or a corner of a building... a 1 5 ° slop or a fence post ine (r ep r e s e nts dl o n g d otte l Fold a Sight and hold this level with a vertical tree... 15° Use this page as a guide to determine slopes where you may not operate safely. e) WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding mowers up and down slopes, never across the face of slopes. Operate walk-behind mowers across the face of slopes, never up and down slopes. Section 2 — Important Safe Operation Practices 3 Assembly & Set-Up Contents of Carton • One Lawn Mower • One Lawn Mower Operator’s Manual • Assembly Handle NOTE: This lawn mower is shipped without gasoline or oil in the engine. Fill up the gasoline and oil as instructed in the accompanying engine manual BEFORE operating your mower. 1. 1. For shipping purposes, the chute deflector on your mower is held in an upright position by a retainer. Remove the retainer as follows: a. Push the chute deflector up towards the engine. Holding the deflector in this position, remove the retainer and discard. See Fig. 3-1. b. Lower the chute deflector carefully keeping your fingers out of the way. One Bottle of Oil Perform the following sequence for the handle setup: NOTE: Your mower is shipped with the handle in the higher height position. a. Lift the upper handle up from folded position and pull it to extended position following the arrow in Fig. 3-2. The handle should click into this position. B A Figure 3-2 b. Figure 3-1 Make sure the carriage bolt is seated properly in the handle. Tighten the star knobs securing the upper handle to the lower handle. 2. If satisfied with the height of the handle, tighten the star knobs at the ends of the lower handle shown in Fig. 3-3. For convenience of operation, you may adjust the handle height as follows: 3. Position the recoil starter by following the steps below: a. Hold the blade control against the upper handle. b. Slowly pull the starter rope out of the engine. See Fig. 3-4. A B D C Figure 3-3 Figure 3-4 NOTE: Each end of the lower handle must be placed in the same position on the mounting brackets. a. Remove the star knobs shown in Fig. 3-3 and remove the lower handle. b. Position each handle bracket stud into the top hole in the lower handle. c. Tighten the star knobs. 4. c. Slip the starter rope into the rope guide. d. Tighten the rope guide wing nut. Use the cable tie provided to secure cable to the lower handle. Pull the cable tie tight and trim excess. See Fig. 3-5. Figure 3-5 Section 3 — Assembly & Set-Up Mulching Baffle (If Equipped) Adjustments 1. Cutting Height If your mower is equipped with an optional mulching baffle, install it on the right side of the deck. Follow the sequence indicated here. a. b. Lift up and hold the side-discharge chute deflector and insert the bottom lip of the mulching baffle inside the chute opening See Fig. 3-6. Each wheel has a height adjustment lever to change the cutting height of the mower. 1. Depress the height adjustment lever towards wheel. 2. Slide the lever to the desired position for a change in cutting height. See Fig. 3-7. Snap the hooks of the mulching baffle over the hinge pin of the chute deflector. The hooks must snap into place on the hinge pin, locking the mulching baffle firmly onto the mower. Release the chute deflector. 2 1 3 B B A Figure 3-7 3. Figure 3-6 Release the lever towards deck. IMPORTANT: When adjusting the cutting height, be sure to set all four wheels at the same height. For rough or uneven lawns, move the height adjustment lever to a higher position to prevent scalping of the grass. Set-Up Gas and Oil Fill-Up Refer to the Engine Operation section in this manual for additional engine information. 1. Add oil provided before starting unit for the first time out of the box. 2. Service the engine with gasoline as instructed in the Engine Operation section of this manual. WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and any other sources of ignition. 10 Section 3 — Assembly & Set-Up 4 Controls and Features Blade Control Choke Control Recoil Starter Cutting Height Adjustment Lever (one at each wheel) Figure 4-1 Recoil Starter The blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle to operate the unit. Release it to stop engine and blade. The recoil starter is attached to the right upper handle. Stand behind the unit and pull the recoil starter rope to start the unit. WARNING: This blade control is a safety device. Never attempt to bypass its operations. Cutting Height Adjustment Lever One adjustment lever is located on each wheel and is used to adjust the cutting height. All four levers have to be at the same relative position to ensure a uniform cut. To adjust the cutting height, refer to the “Assembly & Set-Up” Section. Choke Control The choke control is located on the left side of the handle and when activated, closes the choke plate on the carburetor and aids in starting the engine. Pull the choke control to activate the choke on the engine. Use of the choke may not be necessary if the engine is warm or the air temperature is high. Mulching Baffle (If Equipped) The mulching baffle is used to recirculate grass clippings back to the lawn. Attach it as instructed in the Assembly & Set-Up section of this manual. 11 5 Operation Starting Engine 2 WARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operating mower. Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and lawn mower. 1. 1 4 Pull out the choke knob located on the left side of the upper handle. See Fig. 5-1. NOTE: Use of the choke may not be necessary if the engine is warm or the air temperature is high. 2. Standing behind the mower, squeeze and hold the blade control against upper handle. 3. Pull the recoil starter lightly until resistance is felt, then pull rapidly to overcome compression, prevent kickback, and start the engine. Repeat if necessary. See Fig. 5-1. NOTE: Do not allow the recoil starter to snap back against the rope guide. 4. When engine warms up, push in the choke knob. Stopping Engine 1. Release blade control to stop the engine and blade. WARNING: Wait for the blade to stop completely before performing any work on the mower or to remove the mulching baffle (if equipped). Using Your Lawn Mower Be sure lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower or engine. Such objects could be accidently thrown by the mower in any direction and cause serious personal injury to the operator and others. WARNING: The operation of any lawn mower can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear safety glasses while operating the mower, or while performing any adjustments or repairs on it. 12 3 Figure 5-1 Using as Mulcher (If Equipped) For mulching grass, install the mulching baffle as instructed in the “Assembly & Set-Up” section. For effective mulching, do not cut wet grass. If the grass has been allowed to grow in excess of four inches, mulching is not recommended. Use the grass catcher (sold separately) to bag the clippings instead. WARNING: If you strike a foreign object, stop the engine. Remove wire from the spark plug, thoroughly inspect mower for any damage, and repair damage before restarting and operating. Extensive vibration of mower during operation is an indication of damage. The unit should be promptly inspected and repaired. 6 Maintenance & Adjustments Maintenance 4. General Recommendations • Always observe safety rules when performing any maintenance. • The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the lawn mower as instructed here. • Changing of engine-governed speed will void engine warranty. • All adjustments should be checked at least once each season. • Periodically check all fasteners and make sure these are tight. Deck Care Clean underside of the mower deck after each use to prevent build-up of grass clippings or other debris. Follow steps below for this job. 1. Disconnect spark plug wire. Drain gasoline from lawn mower or place a piece of plastic under the gas cap. 2. Tip mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold mower firmly. WARNING: Never tip the mower more than 90º in any direction and do not leave the mower tipped for any length of time. Oil can drain into the upper part of the engine causing a starting problem. 3. WARNING: Always stop engine, disconnect spark plug, and ground against engine before performing any type of maintenance on your machine. Lubricate pivot points on the blade control at least once a season with light oil. This control must operate freely in both directions. See Fig. 6-1. 2. Lubricate the wheels at least once a season with light oil (or motor oil). If wheels are removed for any reason, lubricate surface of the pivot arm and inner surface of the wheel with light oil. See Fig. 6-1. 3. Lubricate the torsion springs and pivot points on the side discharge chute periodically with light oil to prevent rust. See Fig. 6-1. Scrape and clean the underside of the deck with a suitable tool. Do not spray with water. IMPORTANT: Do not use a pressure washer or garden hose to clean your unit. These may cause damage to the engine. The use of water will result in shortened life and reduce serviceability. Lubrication 1. Follow the Engine Maintenance section for lubrication schedule and instruction for engine lubrication. 4. Put the mower back on its wheels on the ground. If you had put plastic under the gas cap earlier, make sure to remove it now. Engine Care NOTE: Refer to the Engine Operation and Maintenance sections in this manual for detailed instructions. • Maintain oil level. • Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. • Clean spark plug and reset the gap once a season. • Clean engine regularly with a cloth or brush. Keep the area around the top of the engine clean to permit proper air circulation. Remove all grass, dirt, and combustible debris from muffler area. Figure 6-1 13 7 Service Blade Care WARNING: An unbalanced blade will cause excessive vibration when rotating at high speeds. It may cause damage to mower and could break causing personal injury. WARNING: When removing the cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade. 5. Lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Slide the blade adapter onto the engine crankshaft. Place the blade on the adapter such that the side of the blade marked “Bottom” (or with part number) faces the ground when the mower is in the operating position. Make sure that the blade is aligned and seated on the blade adapter flanges. 6. Place blade bell support on the blade. Align notches on the blade bell support with small holes in blade. 7. Replace hex bolt and tighten hex bolt to torque: 450 in. lbs. min., 600 in. lbs. max. Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when necessary. Follow the steps below for blade service. 1. 2. Disconnect spark plug boot from spark plug. Turn mower on its side making sure that the air filter and the carburetor are facing up. Remove the bolt and the blade bell support which hold the blade and the blade adapter to the engine crankshaft. See Fig. 7-1. To ensure safe operation of your mower, periodically check the blade bolt for correct torque. Off-Season Storage The following steps should be taken to prepare your lawn mower for storage. Blade Blade Adapter Blade Bell Support Bolt Figure 7-1 3. Remove blade and adapter from the crankshaft. See Fig. 7-1. 4. Remove blade from the adapter for testing balance. Balance the blade on a round shaft screwdriver to check. Remove metal from the heavy side until it balances evenly. When sharpening the blade, follow the original angle of grind. Grind each cutting edge equally to keep the blade balanced. • Clean and lubricate mower thoroughly as described in the lubrication instructions. • Do not use a pressure washer or garden hose to clean your unit. • Coat mower’s cutting blade with chassis grease to prevent rusting. • Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer. When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be taken to rust-proof the equipment. Using a light oil or silicone, coat the equipment, especially cables and all moving parts of your lawn mower before storage. 14 8 Troubleshooting Problem Engine Fails to start Remedy 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4. Prime engine as instructed in the Operation section. 5. Faulty spark plug. 5. Clean, adjust gap, or replace. 6. Blocked fuel line. 7. Engine flooded. 7. Wait a few minutes to restart, but do not prime. 8. Open fuel valve. See engine manual. 9. Engine not choked (if equipped with choke). 9. Choke engine. See engine manual. 1. Spark plug boot loose. 1. Connect and tighten spark plug boot. 2. Blocked fuel line or stale fuel. 2. Clean fuel line; fill tank with clean, fresh gasoline. 3. Vent in gas cap plugged. 3. Clear vent. 4. Water or dirt in fuel system. 4. Drain fuel tank. Refill with fresh fuel. 5. Dirty air cleaner. 5. Refer to engine manual. 6. Unit running with CHOKE (if equipped) applied. 6. Push CHOKE knob in. 1. Engine oil level low. 1. Fill crankcase with proper oil. 2. Air flow restricted. 2. Clean area around and on top of engine. Occasional skips (hesitates) at high speed 1. Spark plug gap too close. 1. Adjust gap to .030”. Idles poorly 1. Spark plug fouled, faulty, or gap too wide. 1. Reset gap to .030” or replace spark plug. 2. Dirty air cleaner. 2. Refer to engine manual. 1. Cutting blade loose or unbalanced. 1. Tighten blade and adapter. Balance blade. 2. Bent cutting blade. 2. See an authorized service dealer. 1. Wet grass. 1. Do not mow when grass is wet; wait until later to cut. 2. Excessively high grass. 2. Mow once at a high cutting height, then mow again at desired height or make a narrower cutting path. 3. Dull blade. 3. Sharpen or replace blade. 1. Wheels not positioned correctly. 1. Place all four wheels in same height position (if equipped with individual height adjusters). 2. Dull blade. 2. Sharpen or replace blade. Engine runs erratic Engine overheats Excessive Vibration Mower will not mulch grass Uneven cut 15 Cause 9 Engine Operation Fuel Cap Air Cleaner Starter Grip Oil Fill Cap Oil Drain Spark Plug Figure 10-1 Pre-Operation Check 10w Oil Recommendations 20w NOTE: This engine is shipped without gasoline or oil in the engine. Running the engine with insufficient oil can cause serious engine damage and void the engine warranty. • 1 Before starting engine, fill with oil. Do not over-fill. Oil capacity is about 20 oz. 20 30 Use a 4-stroke, or an equivalent high detergent, premium quality motor oil certified to meet or exceed U.S. automobile manufacturer’s requirements for service classification SG/SF. Motor oils classified SG/SF will show this designation on the container. 40 20w40, 20w50 15w40, 15w50 SAE 10W-30 is recommended for general, all temperature use. If single viscosity oil is used, select the appropriate viscosity for the average temperature in your area from the chart to the right. 2 10w40 10w30 (ºC) -30º -20º -10º 0º 10º 20º 30º 40º (ºF) -20º 0º 20º 40º 60º 80º 100º Ambient Temperature 1. Single Viscosity 2. Multi Viscosity NOTE: Using non detergent oil or 2-stroke engine oil could shorten the engine’s service life. 16 Check Oil Level NOTE: Be sure to check the engine on a level surface with the engine stopped. 1. Clean around fuel fill before removing cap to fuel. 2. Fill tank to approximately 1-inch below lowest portion of neck to allow for fuel expansion. Be careful not to overfill. 1. Remove the oil filler cap and wipe the dipstick clean. See Fig. 10-2. NOTE: Before refueling, allow engine to cool 2 minutes. Starting The Engine WARNING: Always keep hands and feet clear of equipment moving parts. Do not use a pressurized starting fluid. Vapors are flammable. 1. Pull out the choke knob located on the left side of the upper handle. See Fig. 10-3. Oil Fill Cap/ Dipstick Upper Level 2 Figure 10-2 2. Insert the dipstick into the oil filler neck, but do not screw it in. 3. If the level is low, slowly add oil to the upper limit on the dipstick. See Fig. 10-2 inset. 4. Tighten dipstick firmly before starting engine. NOTE: Do not overfill. Overfilling with oil may cause smoking, hard starting, spark plug fouling, or oil saturation of air cleaner. NOTE: Use of the choke may not be necessary if the engine is warm or the air temperature is high. 2. Standing behind the mower, depress the blade control handle and hold it against the upper handle. 3. Pull the starter grip lightly until resistance is felt, then pull rapidly to overcome compression, prevent kickback, and start engine. Repeat if necessary. See Fig. 10-3. NOTE: Do not allow the starter grip to snap back against the rope guide. Return it gently to prevent damage to the starter. WARNING: Gasoline is extremely flammable and is explosive under certain conditions. Refuel in a wellventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area where the engine is refueled or where gasoline is stored. Avoid repeated or prolonged contact with skin or breathing of vapor. WARNING: Do not overfill the fuel tank (there 1 Figure 10-3 Fuel Recommendations Use automotive gasoline (unleaded or low leaded to minimize combustion chamber deposits) with a minimum of 87 octane. Gasoline with up to 10% ethanol or 15% MTBE (Methyl Tertiary Butyl Ether) can be used. Never use an oil/gasoline mixture, dirty gasoline, or gasoline over 30 days old. Avoid getting dirt, dust, or water in the fuel tank. DO NOT use E85 gasoline. 4 3 4. When engine warms up, push in the choke knob. See Fig. 10-3. Stopping The Engine 1. Release the blade control. should be no fuel in the filler neck). After refueling, make sure the tank cap is closed properly and securely. Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite. If any fuel is spilled, make sure the area is dry before starting the engine. Section 5 — Operation 17 10 Engine Maintenance WARNING: Shut off the engine before performing any maintenance. To prevent accidental start-up, disconnect the spark plug boot. IMPORTANT: If engine must be tipped to transport equipment or to inspect or remove grass, keep spark plug side of engine up. Transporting or tipping engine spark plug down may cause smoking, hard starting, spark plug fouling, or oil saturation of air cleaner. Periodic inspection and adjustment of the engine is essential if high level performance is to be maintained. Regular maintenance will also ensure a long service life. The required service intervals and the kind of maintenance to be performed are described in the table below. Follow the hourly or calendar intervals, whichever occur first. More frequent service is required when operating in adverse conditions. WARNING: If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. Maintenance Schedule First 5 Hours Every Season Every Season Every Season or 25 Hours or 50 Hours or 100 Hours P Check Engine Oil Level Change Engine Oil †† Each Use or Every 5 Hrs. P Check Air Cleaner P P P Service Air Cleaner † P Check Spark Plug P Replace Spark Plug Clean Engine Shroud Clean around muffler P P Replace Fuel Filter † Service more frequently when used in dusty areas. †† Every season or 25 hours if operating under heavy load or high ambient temperature. 18 P Service Dates Oil Service Air Cleaner Service • Check oil level regularly. • Be sure correct oil level is maintained. Check every five hours or daily before starting engine. See oil checking procedure in the Operation section. Paper filters cannot be cleaned and must be replaced once a year or every 100 operating hours; more often if used in extremely dusty conditions. WARNING: Never use gasoline or low flash point solvents for cleaning the air cleaner element. A fire or explosion could result. Oil Change IMPORTANT: Be sure to check engine on a level surface with the engine stopped. Drain the oil while the engine is still warm to assure rapid and complete draining. 1. Remove all fuel from tank by running engine until it stops from lack of fuel. 2. Remove drain plug and allow oil to drain into a suitable container. See Fig. 10-1. IMPORTANT: Never run the engine without the air cleaner. Rapid engine wear will result. 1. Oil Fill Cap Remove the wing bolt and the air cleaner cover. Remove the elements and separate them. See Fig. 10-2. Replace paper element when dirty or damaged. Clean foam element or replace when damaged. Paper Element Level Drain Plug Foam Element Figure 10-2 Figure 10-1 WARNING: Before tipping engine or equipment to drain oil, drain fuel from tank by running engine until fuel tank is empty. 3. Reinstall the drain plug and tighten it securely. 4. Refill with the recommended oil (see Operation section) and check the oil level. See Fig. 10-1. 5. Reinstall the oil fill cap securely. 2. To clean foam element, separate it from the paper element and wash in liquid detergent and water. Allow to dry thoroughly before using. Do not oil the foam element. IMPORTANT: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil. NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground. Section 10 — Engine Maintenance 19 Spark Plug Service 3. WARNING: DO NOT check for spark with spark Measure the plug gap with a feeler gauge. Correct as necessary by bending side electrode. See Fig. 10-4. The gap should be set to 0.030 in. plug removed. DO NOT crank engine with spark plug removed. To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug boot and use a spark plug wrench to remove the plug. See Fig. 10-3. Spark Plug 0.030 in. Figure 10-4 4. Check that the spark plug washer is in good condition and thread the spark plug in by hand to prevent crossthreading. 5. After the spark plug is seated, tighten with a spark plug wrench to compress the washer. Spark Plug Boot Figure 10-3 WARNING: If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. 2. 20 Visually inspect the spark plug. Discard the spark plug if there is apparent wear, or if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused. Section 10— Engine Maintenance NOTE: When installing a new spark plug, tighten 1/2 turn after the spark plug seats to compress the washer. When reinstalling a used spark plug, tighten 1/8-1/4 turn after the spark plug seats to compress the washer. IMPORTANT: The spark plug must be securely tightened. An improperly tightened spark plug can become very hot and may damage the engine. Fuel Filter Service Storage The fuel filter cannot be cleaned and must be replaced once a year or every 100 operating hours; more often if run with old gasoline. Engines stored between 30 and 90 days need to be treated with a gasoline stabilizer and engines stored over 90 days need to be drained of fuel to prevent deterioration and gum from forming in fuel system or on essential carburetor parts. If the gasoline in your engine deteriorates during storage, you may need to have the carburetor, and other fuel system components, serviced or replaced. 1. Remove all fuel from tank by running engine until it stops from lack of fuel. 2. Remove c-clamp from fuel line and remove fuel line from tank outlet. See Fig. 10-5. 1. Remove all fuel from tank by running engine until it stops from lack of fuel. WARNING: Never leave engine unattended while running. Figure 10-5 2. Change oil. See Oil Change section. 3. Remove spark plug and pour about 1/2 an ounce of engine oil into cylinder. Replace spark plug and crank slowly to distribute oil. 4. Clean debris from around engine, under finger guard, and under, around and behind muffler. Touch up any damaged paint, and coat other areas that may rust with a light film of oil. 5. Store in a clean, dry and well ventilated area away from any appliance that operates with a flame or pilot light, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark producing electric motor, or where power tools are operated. 6. If possible, also avoid storage areas with high humidity, because that promotes rust and corrosion. Keep the engine level in storage. Tilting can cause fuel or oil leakage. 3. Pull out old fuel filter from tank outlet. Replace when dirty or damaged. 7. 4. Grasp new fuel filter from shouldered end and insert it completely to the shoulder into the tank outlet. See Fig. 10-5 inset. Removing From Storage 5. Clean Engine If the engine has been running, allow it to cool for at least half an hour before cleaning. Periodically remove dirt build-up from engine. Clean finger guard and around muffler. Clean with a brush or compressed air. IMPORTANT: Do not spray engine with water to clean because water could contaminate fuel. Using a garden hose or pressure washing equipment can also force water into the air cleaner or muffler opening. Water in the air cleaner will soak the paper element, and water that passes through the element or muffler can enter the cylinder, causing damage. 1. Check your engine as described in the Pre-Operation Check section of this manual. 2. If the fuel was drained during storage preparation, fill the tank with fresh gasoline. If you keep a container of gasoline for refueling, make certain it contains only fresh fuel. Gasoline oxidizes and deteriorates over time, causing hard starting. 3. If the cylinder was coated with oil during storage preparation, the engine will smoke briefly at startup. This is normal. WARNING: Accumulation of debris around muffler could cause a fire. Inspect and clean before every use. Section 10 — Engine Maintenance 21 17 5 38 37 3 2 4 1 7 30 27 6 36 33 35 28 34 29 A 39 27 8 26 31 9 A 23 15 14 24 18 19 20 25 21 31 16 32 22 14 18 15 32 16 14 10 14 11 12 13 22 Part Number Description Ref. Part Number Description 1. 710-1205 Eye Bolt 21. 710-0599 TT Screw, 1/4-20 x .5 2. 720-0279 Wing Nut 22. 736-0270 Bell Washer, .265 ID x .75 OD 3. 747-1161A Blade Control Handle 23. 710-0216 Screw, 3/8-16 x .75 4. 749-1092A Upper Handle 24. 738-1173 Shoulder Screw 5. 746-04300 25. 734-1987 Rear Wheel, 8 x 1.8, Bar 6. 749-04037 Lower Handle 26. 682-3064 Handle Bracket Assembly, RH 682-3065 Handle Bracket Assembly, LH 7. 725-0157 Cable Tie — 8. 687-02048 Deck Assembly, 22” 27. 720-04072 Star Knob 9. 710-0654A TT Screw, 3/8-16 x 1.0 28. 731-04019 Trailshield 10. 748-0376A Blade Adapter 29. 17098 Hinge Clip 11. 742-0642A Standard Blade, 22” 30. 710-1174 Carriage Bolt, 5/16-18 x 2 12. 736-0524 Blade Bell Support 31. 720-0426 Knob 732-1026 Lever 13. 710-1044 Screw, 3/8-24 x 1.5 32. 14. 712-04065 Lock Nut, 3/8-16 33. 732-1014 Torsion Spring 15. 741-04242 Height Adjuster Bearing 34. 17032A Chute Hinge 16. 687-02342 Pivot Arm 35. 747-0710 Hinge Pin 17. 746-04295A Choke Cable 36. 731-1034B Hinged Chute Deflector Assembly 18. 736-0741 Bell Washer, .760 OD x 1.25 OD 37. 710-0606 Screw, 1/4-20 x 1.50 19. 738-1172 Shoulder Screw 38. 712-04064 Nut, Flange Lock, 1/4-20 20. 734-1988 Front Wheel, 7 x 1.8, Bar 39. 631-04045† Mulching Baffle † If Equipped 23 Engine Model - 1P61 21 29 8 9 15 20 1 7 3 13 2 19 18 24 25 11 26 17 10 17 6 28 4 5 12 14 27 22 23 16 24 Engine Model - 1P61 Ref No. Part Number 1. 951-10337 Fuel Tank 2. 951-10336 Flywheel Shroud 3. 951-10335 Rubber Fuel Tank Mounting Washer 4. 951-10334 Oil Filler Tube Assembly 5. 951-10333 Dipstick Assembly 6. 951-10330 Cylinder Head Complete 7. 951-10327 Short Block Assembly 8. 951-10320 Stop Switch and Brake Assembly 9. 951-10319 Recoil Spring and Pulley Assembly 10. 951-10314 Push Rod Kit 11. 951-10313 Valve Kit 12. 951-10370 Oil Drain Plug and Washer Assembly 13. 951-10367 Ignition Coil 14. 951-10308 Carburetor Assembly 15. 951-10307 Flywheel Key 16. 951-10305 Air Cleaner Housing Assembly Complete 17. 951-10304 Muffler Stud Assembly 18. 951-10363 Fuel Line Kit – Inc. hoses, clamps & filter 19. 951-10358 Fuel Filter 20. 951-10300 21. 951-10299 Recoil Starter Assembly 22. 951-10298 Air Cleaner Kit 23. 951-10297 Air Cleaner Thumb Screw 24. 951-10296 Muffler Guard 25. 951-10295 Muffler 26. 951-10294 Muffler Gasket /Heat Shield 27. 951-10293 Governor Return Spring 28. 951-10292 Spark Plug – 952Z1P61 Engine – Complete – 951-10324 Carburetor Kit – Major – 951-10322 Carburetor Kit – Minor – 951-10316 Gasket Kit – Complete – 951-10315 Gasket Kit – External Description NOTE: Illustrated parts without a numeric call-out are not servicable components. 25 MTD LLC (MTD), The United States Environment Protection Agency (U. S. EPA) Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations) The U. S. EPA and MTD are pleased to explain the emissions control system warranty on your model year 2005 and later small off-road engine. New small off-road engines must be designed, built and equipped to meet the stringent anti-smog standards. MTD must warranty the emission control system on your engine for the period of time listed below, provided there has been no abuse, neglect or improper maintenance of your small off-road engine. Your emission control system may include parts such as the carburetor, air cleaner, ignition system, exhaust system, and other associated emission-related components. Where a warrantable condition exists, MTD will repair your small off-road engine at no cost to your including diagnosis, parts and labor. MANUFACTURER’S WARRANTY COVERAGE: This emissions control system is warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by MTD. OWNER’S WARRANTY RESPONSIBILITIES: As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. MTD recommends that you retain all your receipts covering maintenances on your small off-road engine, but MTD can not deny warranty solely for the lack of receipts or for your failure to ensure the performance to all scheduled maintenance. As the small off-road engine owner, you should however be aware that MTD may deny your warranty coverage if your small off-road engine or part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your small off-road engine to an Authorized MTD Service Dealer as soon as a problem exists. The warranted repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact a MTD Service Representative at 1-800-800-7310 and address is MTD LLC, P.O. Box 361131, Cleveland OH, 44136-0019. Defects Warranty Requirements for 1995 and Later Small Off-Road Engines: This section applies to 1995 and later small off-road engines. The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser. (a) General Emissions Warranty Coverage MTD must warrant to the ultimate purchaser and each subsequent purchaser that the engine is: (1) Designed, built, and equipped so as to conform with all applicable regulations adopted by the Air Resources Board pursuant to its authority in Chapters 1 and 2,Part 5, Division 26 of the Health and Safety Code; and (2) Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to the part as described in the engine manufacturer’s application for certification for a period of two years. (b) The warranty on emissions-related parts will be interpreted as follows: (1) Any warranted part that is not scheduled for replacement as required maintenance in the written instructions required by Subsection (c) must be warranted for the warranty period defined in Subsection (a)(2). If any such part fails during the period of warranty coverage, it must be repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under the warranty must be warranted for the remaining warranty period. (2) Any warranted part that is scheduled only for regular inspection in the written instructions required by Subsection (c) must be warranted for the warranty period defined in Subsection (a)(2). A statement in such written instructions to the effect of “repair or replace as necessary” will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for the remaining warranty period. (3) Any warranted part that which is scheduled for replacement as required maintenance in the written instructions required by Subsection (c) must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under warranty must be warranted for the remainder of the period prior to the first scheduled replacement point for the part. (4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warranty station. (5) Notwithstanding the provisions of Subsection (4) above, warranty services or repairs must be provided at all MTD distribution centers that are franchised to service the subject engines. (6) The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station. EPA-1 (7) The engine manufacturer is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part. (8) Throughout the engine’s warranty period defined in Subsection (a)(2), MTD will maintain a supply of warranted parts sufficient to meet the expected demand for such parts. (9) Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the warranty obligations of MTD. (10) Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts shall be grounds for disallowing a warranty claim made in accordance with this article. The engine manufacturer shall not be liable under this article to warrant failures of warranted parts caused by the use of non-exempted add-on or modified part. (c) MTD will include a copy of the following emission warranty parts list with each new engine, using those portions of the list applicable to the engine. (1) Fuel Metering System • Cold start enrichment system (soft choke) • Carburetor and internal parts • Fuel Pump (2) Air Induction System • Air cleaner • Intake manifold (3) Ignition System • Spark plug(s) • Magneto Ignition System (4)Exhaust System (5) Miscellaneous Items Used in Above System • Vacuum, temperature , position, time sensitive valves and switches • Connectors and assemblies EPA-1 MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/ or its territories and possessions (either entity respectively, “MTD”). “MTD” warrants this product (excluding its Normal Wear Parts and Attachments as described below) against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster. Damage resulting from the installation or use of any part, accessory or attachment not approved by MTD for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal Wear Parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades, blade adapters, tines, grass bags, wheels, rider deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber, engine oil, air filters, spark plugs and tires. Attachments — MTD warrants attachments for this product against defects in material and workmanship for a period of one (1) year, commencing on the date of the attachment’s original purchase or lease. Attachments include, but are not limited to items such as: grass collectors and mulch kits. HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To locate the dealer in your area: In the U.S.A. Check your Yellow Pages, or contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call 1-800-800-7310, 1-330-2204683 or log on to our Web site at www.mtdproducts.com. In Canada Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800668-1238 or log on to our Web site at www.mtdcanada.com. This limited warranty does not provide coverage in the following cases: c. Service completed by someone other than an authorized service dealer. d. MTD does not extend any warranty for products sold or exported outside of the United States and/or Canada, and their respective possessions and territories, except those sold through MTD’s authorized channels of export distribution. e. Replacement parts that are not genuine MTD parts. f. Transportation charges and service calls. g. MTD does not warrant this product for commercial use. No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind MTD. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above. The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. MTD shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use the product. This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift. HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage. a. Log splitter pumps, valves, and cylinders have a separate oneyear warranty. b. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments, deck adjustments, and normal deterioration of the exterior finish due to use or exposure. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683 MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238 GDOC-100016 REV. B Podadora de Empuje — Modelo 08M ADVERTENCIA LEA Y SIGA TODAS LAS INSTRUCCIONES DE ESTE MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MÁQUINA. SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Al propietario 1 ◊ Visite nuestro sitio web en www.mtdproducts.com ◊ ◊ Escríbanos a MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019 2 2. 3. 4. 5. 6. 7. 8. 9. 21. 10. 22. 11. 23. 24. a. b. c. d. 12. 13. 14. 15. 2. 3. 16. 17. 18. 1. 2. 3. 19. 20. 1. 11. 2. 12. 3. 4. 13. 14. 5. 6. 2. 3. 4. 5. 6. 7. 8. 9. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. GUARDE ESTAS INSTRUCCIONES pend i e n t e de ) 15 g r a dos na pr e s e n ta u re Do b l e a lo l a r g o de l a l í nea p u n tead a ( q ue 15 3 Una Podadora • Uno Manual de Operador Montaje Manija 1. 1. b. Uno Botella del Aceite • B A Figura 3-2 b. Figura 3-1 2. 3. A B D C Figura 3-4 a. b. c. d. b. c. 4. Figura 3-5 Tolva de Abono (De Ser equipado) Ajustes 1. b. 1. 2. 2 1 3 B B Figura 3-7 A 3. Figura 3-6 2. 10 4 Tolva de abono Figura 4-1 11 5 2. 3. 12 4 4. 1 3 Figura 5-1 6 3. 4. • • • • 2. ADVERTENCIA: Detenga siempre el motor, 2. 3. Verifique el nivel de aceite. • • • Figura 6-1 13 7 5. 6. 7. 2. • • • Cuchilla 3. 4. 14 8 Causa Remedio 4. ESTÁRTER no activado. (De ser equipado) 2. Flujo de aire restringido. 1. Ajuste la distancia disruptiva a 0,76 mm (0,03 pulg). 1. Bujía atorada, averiada o exceso de distancia disruptiva. 15 16 Causa Remedio 2. Cuchilla abollada. 2. Consulte a un distribuidor autorizado. 1. Césped húmedo. 2. Césped excesivamente alto. 3. Afile o cambie la cuchilla. 2. Afile o cambie la cuchilla. 9 Depurador de aire Tubo de drenaje 10w 20w 1 30 40 20w40, 20w50 15w40, 15w50 2 10w40 10w30 (ºC) -30º -20º -10º 0º 10º 20º 30º 40º (ºF) -20º 0º 20º 40º 60º 80º 100º 20 Viscosidad monogrado 2. Viscosidad multigrado 17 Verifique el Nivel de Combustible 1. 2. Nivel superior Figura 10-2 2. 3. 4. 2 4 3 1 Figure 10-3 2. 3. 18 10 Cada tempo- Cada tempo- Cada temporada o cada rada o cada rada o cada 25 horas 50 horas 100 horas P P P P P P P Cada uso o cada 5 horas P P P 19 • 2. Nivel Elemento de espuma Figura 10-1 4. 5. 20 Figura 10-2 2. 3. 0,030 pulg. Figura 10-4 4. 5. 21 1. 2. 1. 3. 4. 5. 6. 7. Figura 10-5 3. 4. 5. Limpie el Motor 1. 2. 3. 22 Notas 11 23 24 Notes Notas 25 EPA-1 GARANTÍA LIMITADA DEL FABRICANTE PARA Contacte MTD Products Limited, Kitchener, ON N2G 4J1, llame al 1-800-668-1238 o visite nuestro sitio web en www.mtdcanada.com. MTD LLC. P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Teléfono: 1-800-800-7310, 1-330-220-4683 MTD Canada Limited - KITCHENER, ON N2G 4J1; teléfono 1-800-668-1238 GDOC-100016 REV. B
advertisement