Norelco HQ40/20, HQ41/15, HQ40/33, HQ40/35, HQ40/15, HQ40/18, HQ40, HQ40/14 User manual
Add to my manuals
3 Pages
advertisement
▼
Scroll to page 2
of 3
HQ41, HQ40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ENGLISH Important Read this user manual carefully before you use the appliance and save it for future reference. -- Keep the appliance dry (Fig. 1). -- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. -- Children should be supervised to ensure that they do not play with the appliance. -- Use and store the appliance at a temperature between 5°C and 35°C. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. ,, For easy and optimal cleaning, the Philips Action Clean (shaving head cleaner, type HQ100) is available. Ask your Philips dealer for information (Fig. 8). Note:The Philips Action Clean may not be available in all countries. Contact the Customer Care Centre in your country about the availability of this accessory. You can also clean the shaver in the following way: Every week: shaving unit and hair chamber 1 Switch off the shaver. 2 Clean the top of the appliance first, using the brush supplied (Fig. 9). 3 Press the release button (1) and remove the shaving unit (2) (Fig. 10). 4 Clean the inside of the shaving unit and the hair chamber with the brush (Fig. 11). 5 Put the shaving unit back onto the shaver. Every two months: shaving heads Inserting batteries The appliance runs on two R6 AA 1.5-volt batteries. Preferably use Philips alkaline batteries. 1 Switch off the shaver. Make sure that your hands are dry when inserting the batteries. 3 Remove the retaining frame by pushing the sides of the central spring towards each other (1) and lifting the retaining frame out of the shaving unit (2) (Fig. 12). 1 Remove the lid of the battery compartment (Fig. 2) 2 Place two batteries in the battery compartment (Fig. 3). Make sure the + and - indications on the batteries match the indications in the battery compartment. The shaver does not work if the batteries have been placed incorrectly. 3 Put the lid of the battery compartment back onto the appliance. First insert the top part of the lid (1) and then press the bottom part down until you hear a click (2) (Fig. 4). ,, To avoid damage due to battery leakage: -- do not expose the appliance to temperatures higher than 35 cC; -- remove the batteries if the appliance is not going to be used for a month or more; -- do not leave empty batteries in the appliance. Cordless shaving time Two new batteries offer a cordless shaving time of 60 minutes. Using the appliance Shaving 1 Switch on the shaver by pressing the switch lock and pushing the on/off slide upwards (Fig. 5). The switch lock prevents accidental switching on of the appliance. 2 Move the shaving heads quickly over your skin, making both straight and circular movements (Fig. 6). Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 3 Switch off the shaver by pushing the on/off slide downwards. 4 Put the protection cap on the shaver every time you have used it, to prevent damage (Fig. 7). Cleaning and maintenance Regular cleaning guarantees better shaving performance. 2 2 Press the release button (1) and remove the shaving unit (2) (Fig. 10). 4 Slide the shaving heads out of the retaining frame and clean them one by one (Fig. 13). Do not mix up the cutters and the guards. This is essential since each cutter has been ground with its corresponding guard for optimal performance. If you accidentally mix the sets up, it could take several weeks before optimal shaving performance is restored. 5 Clean the cutter with the short-bristled side of the brush (Fig. 14). Brush carefully in the direction of the arrow. 6 Brush the guard (Fig. 15). 7 Slide the shaving heads back into the retaining frame and put the retaining frame back into the shaving unit (Fig. 16). 8 Put the shaving unit back onto the shaver. ,, For extra thorough cleaning, clean the shaving heads by putting them in a degreasing liquid (e.g. alcohol) every six months. To remove the shaving heads, follow steps 1 to 4 described above. After cleaning, lubricate the central point on the inside of the guards with a drop of sewing machine oil to prevent wear of the shaving heads (Fig. 17). Storage ,, Put the protection cap on the shaver to prevent damage (Fig. 7). Replacement Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ4 Ç Philips shaving heads only. 4 Slide the shaving heads out of the retaining frame (Fig. 13). 5 Slide new shaving heads into the retaining frame (Fig. 16). 6 Put the retaining frame back into the shaving unit (Fig. 18). 7 Put the shaving unit back onto the shaver. Accessories The following accessories are available: -- HQ4 Ç Philips shaving heads. -- HQ100 Philips Shaving Head Cleaner (not available in China). -- HQ101 Philips Shaving Head Cleaning fluid (not available in China). -- HQ110 Philips Shaving Head Cleaning Spray (not available in China). Environment -- Batteries contain substances that may pollute the environment. Remove the batteries when they are empty or when you discard the appliance. Do not throw away the batteries with the normal household waste, but hand them in at an official collection point. -- Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 19). Guarantee & service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, go to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear. Troubleshooting 1 Reduced shaving performance ,, Cause 1: the shaving heads are dirty.The shaver has not been cleaned well enough or has not been cleaned for a long time. -- Clean the shaver thoroughly before you continue shaving. See chapter ‘Cleaning and maintenance’. ,, Cause 2: long hairs are obstructing the shaving heads -- Clean the cutters and guards with the brush supplied. See chapter ‘Cleaning and maintenance’, section ‘Every two months: shaving heads’. ,, Cause 3: the shaving heads are damaged or worn. -- Replace the shaving heads. See chapter ‘Replacement’. 2 The shaver does not work when the on/off slide is pushed upwards. ,, Cause: the batteries are empty -- Replace the batteries. See chapter ‘Inserting batteries’. 1 Switch off the shaver. 2 Press the release button (1) and remove the shaving unit (2) (Fig. 10). 3 Remove the retaining frame by pushing the sides of the central spring towards each other (1) and lifting the retaining frame out of the shaving unit (2) (Fig. 12). 4222.002.5087.3 简体中文 更换 4222.002.5087.3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Rotation shaver Black, Silver
- Number of shaver heads/blades: 2
- Battery