Levana Jena User manual

Jena
™
Digital Baby Video Monitor
Moniteur vidéo bébé numérique
Video Monitor Digital para Bebé
MANUAL
MANUEL
MANUAL
mylevana.com
SAFETY WARNINGS
This product cannot replace responsible adult supervision.
CAUTION: Keep small parts away from children.
Strangulation Hazard: Children can become entangled in
cords. Power cords should be kept more than 3 feet away
from the crib and baby’s reach at all times. Baby monitors and
cameras with power cords should never be hung on or near
the crib.
This product is not a toy and should be kept out of
children’s reach.
Use only with provided power supply.
The socket-outlet shall be installed near the equipment and
shall be easily accessible.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE!
Dispose of used batteries according to the instructions.
This product contains small parts. Exercise care when
unpacking and assembling the product.
Use only batteries/power supplies listed in the user manual.
Read and Keep Instructions: All the safety and operating
instructions should be read before the video baby monitor is operated.
Water and Moisture: This product is designed for indoor use only. The unit should not be exposed to rain, moisture, dripping or splashing. No
objects filled with liquid should be placed on top of, or beside the product, such as a glass or vase. This item should not be used near water.
Non-Use Periods: Always unplug the AC adapters from the wall outlets during long periods of non-use.
Ventilation: This baby monitor should not be used on a bed, sofa, rug or similar surface that may block the ventilation openings, or be placed in an
enclosed area, such as a bookcase or drawer that may impede air flow.
Keep Away from Sources of Heat: This unit should not be exposed to direct heat sources such as a candle, fireplace, radiator, heat register, stove
or other appliance that emits heat. The unit should not be left in direct sunlight.
Power Source: This unit should only be used with the power adapters included in this package (rated 6V DC)
Damage Requiring Service: This unit should be serviced by qualified personnel only when:
a.
b.
c.
d.
Objects have fallen or liquid has been spilled into the product
The units have been exposed to rain
The units do not appear to operate normally or exhibits a distinct change in performance
The units have been dropped or the enclosure damaged
2
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful inerference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3
Please visit our website at www.mylevana.com for information about your
product’s warranty
We take quality very seriously. This is why all of our products come with a one-year warranty from the original purchase date against
defects in workmanship and materials. If you have warranty or support issues please contact us using any of the following methods:
Web: www.mylevana.com
Support: www.mylevana.com/support
LEVANA USA
60 Industrial Parkway #Z64
Cheektowaga NY
USA 14227
Warranty Terms
1.
LEVANA® products are guaranteed for a period of one year from the date of purchase against defects in workmanship and materials.
This warranty is limited to the repair, replacement or refund of the purchase price at LEVANA’s option.
2. This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered with contrary to the
applicable instruction manual.
3. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this warranty.
4. The warranty expressly provided for herein is the sole warranty provided in connection with the product itself and no other warranty,
expressed or implied is provided. LEVANA assumes no responsibilities for any other claims not specifically mentioned in this warranty.
5. This warranty does not cover the shipping cost, insurance or any other incidental charges.
6. You MUST contact LEVANA at www.mylevana.com/support before sending any product back for repair. You will be sent a Return
Authorization form with return instructions. When returning the product for warranty service, please pack it carefully in the original
box with all supplied accessories, and enclose your original receipt or copy, and a brief explanation of the problem (include RA #).
7. This warranty is valid only in Canada and the continental U.S.
8. This warranty cannot be re-issued.
4
5
WHAT’S INCLUDED
•
•
•
•
•
•
•
•
Baby Video Monitor
Night Vision Camera
Rechargeable Lithium Ion Battery
2 Power Adapters
Charging Base for Monitor
Quick Start Quide
1 Year Warranty
Lifetime Customer Support
This product is not a toy. This product contains small parts. Exercise care when unpacking and assembling the product.
Battery life of 8 hours based on full duration testing. Battery life may vary depending on usage.
Night vision range up to 15ft under ideal conditions. Objects at or beyond this range may be partially or completely obscured, depending on the camera application.
Optimum range is 150ft when signal is passing through walls or floors. Microwave ovens (when in use) may cause signal disruption at close range. Buildings with metal frames
may also cause signal disruption. Maximum transmission range is 500 feet.
This product does not replace responsible adult supervision. Check on your child at regular intervals and make sure your monitor is always adequately charged.
Strangulation Hazard: Children can become entangled in cords. Power cords should be kept more than 3 feet away from the crib and baby’s reach at all times. Baby monitors/
cameras with power cords should never be hung on or near the crib.
We reserve the right to change models, configuration, or specifications without notice or liability. Product may not be exactly as shown.
©2013 LEVANA®. All rights reserved. LEVANA®, the LEVANA® logo, Jena™ and other LEVANA® marks may be registered. All other Trademarks are the property of their respective owners.
6
MONITOR
1. ANTENNA
Transmits and receives
signals
12. VOLUME –
Decreases the volume
through the speaker
2. VOLUME LEDS
Indicates the amount of
sound being heard by
the camera
13. TALK TO BABY™
Press and hold to talk,
release to listen
3. 2.4" SCREEN
14.LULLABIES
5 Remote-controlled
lullabies to choose from
4. POWER/SCREEN ON-OFF
1
2
6. BELT CLIP/TABLE STAND
15. PAIRING LED
Flashes red quickly when
pairing
7. PAIRING BUTTON
16.SPEAKER
8. Power LED
Green when monitor has
power
17. CHARGING BASE
5. MENU/ZOOM BUTTON
3
6
9.MICROPHONE
Captures the sound of
your voice when using
Talk to Baby™
10. BATTERY COMPARTMENT
11. VOLUME +
Increases the volume
through the speaker
10
17
7
4
11
5
12
7
8
13
14
15
9
16
CAMERA
1
5
6
2
3
12
7
9
8
4
10
11
1. ANTENNA
5. NIGHTLIGHT
9. PAIRING BUTTON
2. NIGHT VISION LEDs
6. NIGHT VISION LIGHT SENSOR
10. TEMPERATURE SENSOR
3. CAMERA LENS
7. ON/OFF BUTTON
11. POWER INPUT
4. MICROPHONE
8. POWER LED
12. SPEAKER
8
SETUP
Battery Installation - Monitor
1
3
1. Gently remove the BATTERY COMPARTMENT COVER on the back of the monitor
by sliding down.
2. Insert the included rechargeable battery, plug the battery cord into the small jack
on the inside of the battery compartment.
3. Slide the BATTERY COMPARTMENT COVER back into place.
4. For extended periods of non-use, please remove battery from baby monitor.
Battery Installation - Camera
The camera unit can be powered using 4 AAA batteries instead of the included adapter
1. Gently remove the BATTERY COMPARTMENT COVER on the bottom
of the camera base, using a small phillips (cross) head screwdriver.
2. Insert 4 AAA batteries in the compartment (not included), paying
close attention to the labelled polarity markings.
3. Replace the battery compartment cover using the small screwdriver.
4.The POWER LED will flash when the battery charge is low.
2
Battery
Compartment
cover
Get the Most Out of Your Rechargeable Battery
Fully charge battery (4 hours) before first use.
To maximize battery life, charge battery before battery is fully drained.
Turn LCD screen OFF; press POWER
side of the monitor ONCE.
button on the VOX PEEP Mode: After 1 minute of inactivity, monitor Avoid extreme heat or cold as this will affect the life of the battery.
9
enters standby/sleep mode (when activated).
Adjustable Brightness: Decreasing screen brightness will extend battery life.
SETUP
Connecting Power to the Monitor / Charging Battery
1. Connect the power adapter attached to the charging dock marked MONITOR
into an available wall outlet. For safety reasons, ONLY use the adapters included in
the package.
2. With the battery in the monitor, place the monitor into the charging dock with the
screen facing you.
3. Press and hold the POWER button on the side of the monitor to turn
the monitor ON.
4. The icon in the top right corner of the main screen will show you the battery power status.
EMPTY
CHARGING
FULL
Note: When monitor battery is low, POWER LED will
flash slowly & beep. Recharging the battery will be
required shortly after.
Connecting Power to the Camera
1. Take the second power adapter and connect the small end of the power adapter marked
CAMERA
into the DC input on the side of the camera base as shown in the diagram. For
safety reasons, ONLY use the adapters included in the package.
2. On the side of the camera, slide the POWER switch
LEFT to the ON position.
The POWER LED will light up.
Note: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation
hazard. Power cords should be kept no less than 3 feet away from the crib and the baby’s reach at all times.
10
SCREEN ICONS
PAN/TILT
SIGNAL STRENGTH
NO
SIGNAL
TEMPERATURE
STRONG
SIGNAL
ZOOM
2X
BRIGHTNESS
OFF
BATTERY STRENGTH
EMPTY
1X
PEEP MODE
TALK TO BABY™
CAMERA VIEW
1
2
3
4
VOLUME
OFF
DARK
LOW
CHARGING FULL
NIGHTLIGHT
PAIRING
CAMERA
CAM
1
CAM
1
CAM
2
CAM
2
CAM
3
CAM
3
CAM
4
CAM
4
LOW
BRIGHT
LOUD
HIGH
11
OPERATION
Turn the MONITOR ON/OFF
• Press and hold the POWER
• Press and hold the POWER
button on the side of the monitor to turn the monitor ON.
button again to turn OFF the monitor.
Pairing the Camera(s) and Monitor
The camera and monitor come paired (connected) to each other automatically. However, if upon opening this package the
devices do not automatically connect and transmit, you may do so manually. To pair additional cameras, follow the steps
below and be sure to assign a different camera number to each additional camera.
Note: Before you begin pairing, be sure to have the monitor and the camera(s) side by side.
1. To pair your camera and monitor, press and hold the
button on the monitor. Use the
VOLUME arrows (side) to
select a camera number.
2. Press the /
button ONCE. The PAIRING LED flashes red quickly (on monitor).
3. Quickly press and hold the PAIRING
button on the BACK of the camera. A checkmark
will appear next to the
paired camera confirming pairing is successful. Video/audio will be transmitted automatically.
Press and hold
Press and hold
Select a channel
Flashing
Press
12
OPERATION
Placement of the Monitor
The monitor can be used three different ways; placed on a tabletop, attached to your belt or mounted
on the wall.
• Set up the monitor on a tabletop by turning the belt clip DOWN and use the clip as a support stand.
• Carry the monitor on your belt by turning the belt clip UP on the back of the monitor and slide the
clip over your belt.
• Hang the monitor from a screw on the wall using the screw mounting hole in the belt clip.
Placement of the Camera
This camera can be placed on a tabletop or hung on the wall above the area being monitored.
• Place the camera within 15 feet of the area being monitored for best picture results.
• Do not place objects within 2 feet of the field of vision of the camera as the night vision will not activate correctly if objects are too close.
Mounting the Camera on a Tabletop Safely:
1. Place the camera on a tabletop no less than 3 feet away from your
baby’s crib.
2. Feed the power cord down the back of the table or use wall clips
(not included) to secure the cord away so the baby cannot reach it.
3. Plug in the power cord, check the monitor to ensure that you are
getting a good view of your child and there are no obstructions.
3 ft
Note: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation
hazard. Power cords should be kept no less than 3 feet away from the crib and the baby’s reach at all times.
13
OPERATION
Mounting the Camera on a Wall Safely:
Before drilling the holes, it is important to check the reception and camera positioning in the intended location on the wall.
Ensure you are hanging the camera no less than 3 feet away from baby’s crib.
Note: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation
hazard. Power cords should be kept no less than 3 feet away from the crib and the baby’s reach at all times.
1. Pre-drill two holes in the wall using a 3/16”, 4.8mm drill bit.
2. Insert wall anchors (not included) into each hole and tap gently with a hammer until the anchor is flush with the wall.
3. Insert a screw (not included) into each wall anchor and tighten until the screws only stick out about a 1/2 inch.
4. Plug the power cord into the power input of the camera.
5. Locate the wall mounting holes on the bottom of the camera base.
6. Slide the holes over the screws sticking out of the wall.
7. Confirm that the camera is secure, if it is loose you may have to tighten the screws more.
8. Use wall clips (not included) to secure the power cord away from the crib or the
baby’s reach.
9. Connect the other end of the adapter into an available wall outlet.
14
OPERATION
Night Vision
The camera is equipped with Invisible IR (infrared) LEDs which keep the nursery dark.
The LEDs are located on the front of the camera and allow you to see up to 15 feet in
complete darkness so you can check on your baby at any time of night. The night vision
LEDs will activate automatically when the Light Sensor on the front of the camera detects
that the light levels are too low.
INVISIBLE
LEDs
LIGHT
SENSOR
Using Pan/Tilt
The screen allows you to Pan/Tilt the image on the screen (not the camera angle). Press and
hold the /
button. The arrows will appear on the screen. Use the
VOLUME arrows
(side) to go UP/DOWN and use the
buttons (front) to move LEFT/RIGHT.
Using the ZOOM Function
1. Press and hold the /
button. ARROWS will appear on
the screen.
2. Press the /
button again. The X2 icon will appear at the
top of the screen and the arrows will disappear.
button to return to normal view.
3. Press and hold the /
15
X2
OPERATION
Volume
Use the
VOLUME arrows (side) to increase/decrease/
mute the VOLUME.
Nightlight
1. To turn the Nightlight ON/OFF, press the /
until you see the
OFF icon.
2. Use the
VOLUME arrows (side) to select
(MUTE)
button
ON.
Note: Placing the monitor and camera too close together will create
feedback. DECREASE or MUTE the volume and move the camera
away from the monitor.
Using the Talk to Baby™ Two-Way Intercom
With the simple press of a button you can talk to your child at any time without entering the nursery.
1. To talk, press and hold the (TALK) button on the front of the monitor and release to listen.
2. To talk when using multiple cameras, select the camera view (see "Changing the Camera View") and press the
button, release to listen.
(TALK)
Note: To optimize the effectiveness of the
Talk to Baby™ function, please keep the
monitor at least 6-8 inches away from
your mouth.
16
OPERATION
Setting a lullaby
Choose from five different lullabies to soothe your baby to sleep.
1. To select a lullaby, press the LULLABY button.
2. Use the
VOLUME arrows (side) to scroll through the 5 lullabies.
3. To turn OFF the lullabies, press the LULLABY button.
1
Manual Screen OFF
Another power saving feature allows you to turn the screen OFF without turning off the monitor. When sound is detected,
the screen changes to live view.
1.
2.
3.
4.
To turn the screen OFF, press the POWER button ONCE.
When sound is detected, the screen changes to live view.
You must once again turn the screen OFF manually; press the POWER
To return to live view at any time, press the POWER button ONCE.
Changing the Camera View
1. To change the camera view, press the CAMERA
,
,
,
, SCAN.
CAMERA icon
2. Once the camera view is selected,
the corresponding camera icon will
appear at the top left of the screen.
3. Repeat the steps above to return to
any other camera view.
• SCAN cycles through cameras 1
through 4. Each camera view will
appear for 6 seconds per camera.
button. Use the
button ONCE.
VOLUME arrows (side), to select the desired
2
17
OPERATION
Setting the Brightness
Note: Low brightness levels
reduce battery consumption and
extends the battery life.
Brightness Mode sets the brightness of the the screen. Brightness Mode
also extends the battery life.
1. To set the Brightness Mode, press the /
button until you see the
icon.
2. Use the
VOLUME arrows (side) to increase/descrease the
brightness level.
Using VOX (PEEP) Mode
When in VOX (PEEP) Mode, the monitor enters standby/sleep mode after 1 minute of inactivity. When sound is detected, the
screen changes to live view.
• To access live view manually when the screen is off, press the POWER
button ONCE.
• VOX (PEEP) Mode can extend the battery life to more than 12 hours without recharging.
1. To set VOX (PEEP) Mode, press the /
button until you see the
VOX icon.
2. Use the
VOLUME arrows (side) to increase/descrease the
sensitivity to sound.
18
Note: Lower sensitivity levels
reduce battery consumption and
extends the battery life.
OPERATION
Temperature Settings
The ideal temperature for a baby’s room is between 16° - 20° Celcius or 61° - 68° Fahrenheit. Please set or adjust the room
temperature accordingly.
1. To select a Temperature, press the /
button until you see the
2. Use the
VOLUME arrows (side) to select °C or ­°F.
icon.
Temperature Ranges
You can preset alarms which will alert you to temperature changes in the room you are monitoring. An alarm will beep if
the temperature drops below or goes above a selected temperature.
Minimum Temperature range
button until you see the
icon.
1. To select a Minimum Temperature range, press the /
2. Use the
VOLUME arrows (side) to select a temperature between: 59°F - 75°F or 15°C - 24°C.
Maximum Temperature range
button until you see the
icon.
1. To select a Maximum Temperature range, press the /
2. Use the
VOLUME arrows (side) to select a temperature between: 77°F - 95°F or 25°C - 35°C.
19
TROUBLESHOOTING
ISSUE
POSSIBLE SOLUTION
•
•
•
Confirm that the camera and monitor are ON
The battery may be depleted; charge battery
The power adapters may not be properly connected
No reception
•
•
Camera and monitor may not be properly paired; follow PAIRING instructions
Camera may be too far away from the monitor
Reception Interference (static)
•
•
•
•
The camera and monitor may be too far apart
The battery power may be too low
Other electronic devices may be interfering with the signal
The camera or monitor may be placed too close to many metal objects
Feedback (screeching, static)
•
•
The camera and monitor may be too close together
The volume on the monitor may be set too high
Noise (static, beeping)
•
Battery power may be too low
Picture works but there is no sound
•
Volume setting may be too low
Picture is black and white
•
Night vision LEDs may be ON; increase the amount of light in the room being monitored
Day/night vision is whitewashed
•
Ensure that night vision light sensor is pointed away from a wall and is not covered.
The rechargeable battery will
not charge
•
•
The power adapters may not be connected
Battery pack may not be properly connected inside the battery compartment
Maintenance
• Clean the surfaces of the camera and monitor with a soft, fluff-free cloth
• If the units become dirty, use a lightly damp cloth to wipe surfaces, taking care to not allow water into any openings
• Never use cleaning agents or solvents
20
SPECIFICATIONS
MONITOR
MONITOR
Monitor Type
TFT LCD
Housing Material
Screen Size
2.4”
Power Adapter Input
6 V DC
Max. Wireless Range (Line of Sight)
500ft
Dimensions
5.7" x 3" x 1" (l x w x h)
Optimum Wireless Range (Line of Sight)
150ft
Weight
0.40 lbs
480 x 234
Frame Rate
15 FPS
FCC
Private Signal
Yes
FCC ID: SMH-30018BU
Channel Frequencies
2.4GHz
FCC ID: SMH-30018PU
Speaker
Yes
Microphone
Yes
IC
Talk to baby
Yes
IC: 4593A-30018BU
Audio Activation
Yes, adjustable sensitivity
IC: 4593A-30018PU
Battery Operable
Yes, built-in rechargeable
Battery Life (video + audio on)
8 hours
Battery Life (Power Save)
12 hrs
Battery Low Warning (Audible)
Yes
Battery Low Warning (Visual)
Yes
Adjustable Brightness
Yes
Power Save
Yes
21
SPECIFICATIONS
CAMERA
Private Signal
Yes
Maximum Wireless Range (Line of Sight)
500ft
Optimum Wireless Range (Line of Sight)
150ft
Number of IR LEDs
4
Night Vision
Yes, 15ft
Battery Operable
Yes (4 x AAA, not included)
Microphone
Yes
Speaker
Yes
Housing Material
Wall Mountable
Yes
Power Adapter Input
6 V DC
Dimensions
5.5" x 3.3" x 3"
Weight
0.30 lbs
22
NOTES
23
CONSIGNES DE SÉCURITÉ
RISQUE D’EXPLOSION SI LES PILES SONT REMPLACÉES PAR UN
TYPE INCORRECT!
24
25
26
27
CE QUI EST INCLUS
•
•
•
•
•
•
•
•
28
1
2
3
4
11
5
12
7
8
13
14
15
9
16
16.HAUT-PARLEUR
17. BASE DE
CHARGEMENT
6
10
17
29
CAMÉRA
1
5
6
2
3
12
7
9
8
4
10
11
1. ANTENNE
5. VEILLEUSE
9. BOUTON DE JUMELAGE
2. DEL DE VISION NOCTURNE
6. CAPTEUR DE LUMIÈRE
10. CAPTEUR DE TEMPÉRATURE
3. OBJECTIF
7. ALIMENTATION MARCHE-ARRÊT
11. ENTRÉE D’ALIMENTATION
4. MICROPHONE
8. DEL D’ALIMENTATION
12. HAUT-PARLEUR
30
1
3
2
VOX
31
CHARGE CHARGE
EN COURS TERMINÉE
32
FORCE DU SIGNAL
AUCUN SIGNAL
TEMPÉRATURE
SIGNAL
FORT
ZOOM
2X
LUMINOSITÉ
OFF
PUISSANCE DE LA PILE
PILE
ÉPUISÉE 1X
MODE PEEP
TALK TO BABY™
AFFICHAGE CAMÉRA
1
2
3
4
VOLUME
JUMELAGE
OFF
DARK
LOW
VEILLEUSE
CHARGE CHARGE
EN COURS TERMINÉE
BERCEUSES
CAMÉRA
CAM
1
CAM
1
CAM
2
CAM
2
CAM
3
CAM
3
CAM
4
CAM
4
LOW
BRIGHT
LOUD
HIGH
33
`=
O
`=
O
Clignote
Appuyez
34
3 ft
35
36
3 pi
DEL
INVISIBLES
CAPTEUR DE
LUMIÊRE
37
X2
(SOURDINE)
lk
l cc
lk
38
1
C2
C3
C4
2
C2
39
/
/
40
.
41
.
DÉPANNAGE
QUESTION
SOLUTION POSSIBLE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
42
SPÉCIFICATIONS
MONITEUR
MONITOR
TFT ACL
2,4po
6 V CC
500pi
Dimensions
150pi
Poids
0,40 lbs
480 x 234
15 FPS
FCC
Oui
FCC ID: SMH-30018BU
2,4GHz
FCC ID: SMH-30018PU
Oui
Microphone
Oui
IC
Talk to baby
Oui
IC: 4593A-30018BU
Activation audio
IC: 4593A-30018PU
8 heures
12 heures
Oui
Oui
Oui
Oui
43
Oui
500pi
150pi
4
Oui, 15pi
Microphone
Oui
Oui
Oui
6 V CC
Dimensions
5,5po x 3,3po x 3po
Poids
0,30 lbs
44
NOTES
45
INSTRUCCIONES DE SEGURIDAD
RISQUE D’EXPLOSION SI LES PILES SONT REMPLACÉES PAR UN
TYPE INCORRECT!
46
Declaración del IC :
Este aparato digital de la clase b cumple con la norma canadiense ICES-003 del Canadá.
Este dispositivo cumple con la norma RSS 210 de Industry Canada exentos de licencia. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
El fabricante no es responsable de cualquier interferencia de radio o TV causada por la modificación no autorizada de este equipo. Estas modificaciones
podrían invalidar la autoridad del usuario de poner en funcionamiento el equipo.
47
48
49
ELEMENTOS INCLUIDOS
•
•
•
•
•
•
•
•
50
2
3
4
11
5
12
16.PARLANTE
7
8
13
14
15
9
16
17. BASE CARGADORA
6
10
17
51
CÁMARA
1
5
6
2
3
12
7
9
8
4
10
11
1. ANTENA
5. LUZ NOCTURNA
9. BOTÓN DE CONEXIÓN
2. LEDs DE VISIÓN NOCTURNA
6. SENSOR DE LUZ DE VISIÓN
NOCTURNA
10. SENSOR DE TEMPERATURA
3. LENTES DE LA CÁMARA
4. MICRÓFONO
7. BOTÓN ON/OFF
8. ENCENDER LED
52
11. ENTRADA DE POTENCIA
12. PARLANTE
3


VOX
53
CARGANDOCOMPLETA
54
ÍCONOS DE PANTALLA
GIRAR/INCLINAR
POTENCIA DE LA SEÑAL
TALK TO BABY™
NOFUERTE
SEÑALSEÑAL
TEMPERATURA
VACÍA
ZOOM
1X
2X
MODO PEEP:
APAGADO
POTENCIA DE LA BATERÍA
BRILLO
VISIÓN DE CÁMARA
1
2
3
4
VOLUMEN
APAGADO
OSCURIDAD
BAJO
CARGANDO COMPLETA
LUZ NOCTURNA
CONEXIÓN
CANCIONES DE CUNA
CÁMARA
CAM
1
CAM
1
CAM
2
CAM
2
CAM
3
CAM
3
CAM
4
CAM
4
BAJO
BRILLO
ALTO
ALTO
55
Seleccione un canal
Parpadeante
Presione
56
3 ft
57
58
SENSOR
DE LUZ
59
X2
(SILENCIO)
60
1
61
FUNCIONAMIENTO
Ajustar el brillo
UNA VEZ.
62
63
64
RESOLUCIÓN DE PROBLEMAS
PROBLEMA
POSIBLE SOLUCIÓN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
65
ESPECIFICACIONES
MONITOR
MONITOR
Tipo de monitor
TFT LCD
2.4 pul
6 V DC
500 pies
Dimensiones
5.7 pul x 3 pul x 1 pul
150 pies
Peso
0,40 lbs
480 x 234
15 FPS
FCC
Sí
FCC ID: SMH-30018BU
2.4GHz
FCC ID: SMH-30018PU
Altavoz
Sí
Sí
IC
Talk to baby
Sí
IC: 4593A-30018BU
Sí, sensibilidad ajustable
IC: 4593A-30018PU
8 horas
12 horas
Sí
Sí
Ajustar el brillo
Sí
Sí
66
Sí
500 pies
150 pies
4
Sí, 15 pies
Sí
Altavoz
Sí
Sí
6 V CC
Dimensiones
5,5pul x 3,3pul x 3pul
Peso
0,30 lbs
67