Package Contents
B
1 VS0801H 8-port HDMI Switch
1 IR Remote Control Unit
1 Power Adapter
1 Mounting Kit
1 User Instructions
IR Remote Control Unit
11
33
ON / OFF
Important Notice
Considering environmental protection,
ATEN does not provide a fully printed user
manual for this product. If the information
contained in the Quick Start Guide is not
enough for you to configure and operate
your product, please visit our website
www.aten.com, and download the full
user manual.
22
A
Hardware Review
http://eservice.aten.com
Technical Phone Support
Front View
1
1
VS0801H
C
8-Port HDMI Switch
Quick Start Guide
International:
886-2-86926959
Hardware Installation
North America:
1-888-999-ATEN Ext: 4988
OR
United Kingdom:
44-8-4481-58923
3
3
2
2
HDMI Output Device
11
Hardware / Software
Controller
1
Rear View
4
4
1
All information, documentation, and
specifications contained in this package
are subject to change without prior
notification by the manufacturer.
© Copyright 2013 ATEN® International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved.
All other trademarks are the property of their respective owners.
2
3
2
3
3
4
4
3
HDMI
Source Devices
This product is RoHS compliant.
Part No. PAPE-1223-521G
22
Printing Date: 04/2013
8-Port HDMI Switch Quick Start Guide
www.aten.com
IR Remote Control Unit
Source Device(s)
HDMI Type A output connector(s)
Note: A DVI/HDMI adapter is required when connecting a DVI source device.
Source Device Selection
B
1. Port Up / Port Down Buttons
2. Port Selection Buttons
3. On/Off Buttons
Hardware Installation
Display Device
A display device or receiver with an HDMI Type A input connector
Cables
• 1 HDMI cable for each source device you will be connecting
• 1 HDMI cable for your display device
Hardware Review
A
VS0801H Front View
1. Port Selection Pushbuttons
2. Port LEDs
3. IR Receiver
The VS0801H 8-port HDMI Switch offers easy and flexible source device
selection with either the front panel pushbuttons, with the remote control, or
through the RS-232 serial interface.
Note: Whenever the VS0801H is powered on, it automatically selects the first
port connected to a powered on source device. You may choose one of
the methods outlined below to select a different port.
C
1. Use an HDMI cable to connect the HDMI input port on the video display device
to the HDMI output port on the rear of the VS0801H.
2. Use HDMI cables to connect the HDMI output ports on the source device(s) to
the HDMI input ports on the VS0801H. Eight HDMI input ports are located on
the rear of the switch.
3. Plug the provided power adapter into an appropriate AC power source; plug
the power adapter cable into the Power Jack on the VS0801H.
4. Installing the RS-232 Controller (optional)
Installing the RS-232 Controller
In order to use the RS-232 serial interface to attach a high-end controller (such
as a PC) to the VS0801H, use a serial cable such as a modem cable. The end
connecting to the VS0801H should have a 9-pin male connector. Connect this to
the serial interface on the rear of the VS0801H.
VS0801H Rear View
1. HDMI In
2. Power Jack
3. HDMI Out
4. RS-232 Serial Port
Manual Selection
To select a source device, press the pushbutton that corresponds to the port it is
connected to.
Note: The SELECTED LED (green) light indicates which port is currently
selected.
Remote Control Selection
To select a source device with the remote control, press the number button
that corresponds to the port it is connected to. Alternatively, you may also cycle
through the source devices by pushing the Port Up and Port Down buttons on the
remote control unit.
• Use the Port Up button to select the next port in ascending order (from left to
right on the front view panel).
• Use the Port Down button to select the next port in descending order (from right
to left on the front view panel).
RS-232 Serial Interface
The VS0801H’s built-in bi-directional RS-232 serial interface allows system
control through a high-end controller, PC, and/or home automation / home
theater software package.
Configuring the Serial Port
The controller’s serial port should be configured as follows:
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
19200
8
None
1
None
Powering Off and Restarting
If you power off the VS0801H, follows these steps before powering it on again:
1. Power off the attached devices.
2. Unplug the power adapter cable from the VS0801H.
3. Wait 10 seconds, and then plug the power adapter cable back in.
4. After the VS0801H is powered on, power on the attached devices.
A
B
C
www.aten.com
19200
8
Aucun
1
Aucun
www.aten.com
A
B
Hardware installieren
C
Mando a distancia por infrarrojos
A
www.aten.com
B
C
A
Package Contents
1 VS0801H 8-port HDMI Switch
1 IR Remote Control Unit
1 Power Adapter
1 Mounting Kit
1 User Instructions
B
Hardware Review
Front View
IR Remote Control Unit
C
Important Notice
Hardware Installation
Considering environmental protection, ATEN
does not provide a fully printed user manual
for this product. If the information contained
in the Quick Start Guide is not enough for
you to configure and operate your product,
please visit our website www.aten.com,
and download the full user manual.
1
1
OR
11
ON / OFF
33
Online Registration
http://eservice.aten.com
HDMI Output Device
11
Hardware / Software
Controller
3
3
2
2
Technical Phone Support
4
4
International:
886-2-86926959
North America:
1-888-999-ATEN Ext: 4988
22
Rear View
1
United Kingdom:
44-8-4481-58923
1
3
3
22
All information, documentation, and
specifications contained in this package are
subject to change without prior notification by
the manufacturer.
HDMI
Source Devices
2
2
3
4
4
3
www.aten.com
VS0801H Switch HDMI a 8 porte – Guida rapida
Telecomando a infrarossi
Riepilogo hardware
A
B
C
www.aten.com
ケーブル
A
B
C
手動選択
19200
8
None
1
None
www.aten.com
요구사항
소스 장치
A
B
C
Phone: 02 - 467 - 6789
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
19200
8
None
1
None">