window/wall type room air conditioner

WINDOW/WALL - TYPE
ROOM AIR CONDITIONER
Model:KSTAW05C
TA B L E O F C O N T E N T S
Important Safety Instructions ......................1-3
Installation Instructions.................................4-7
Normal Sounds..............................................8
Air Conditioner Features............................8-10
Care and Cleaning...................................10-11
Troubleshooting Tip..................................11-12
Warranty Term..............................................13
Before using your air conditioner, please read
this manual carefully and keep it for future reference.
Producto
1 866
1 866
646 4332
646 4332
MIDEA AMERICA CORPORATION
PRODUCT REGISTRATION CENTER
11800 NW 100 ROAD STE 4
MEDLEY FL 33178-1037
IMPORTANT SAFETY INSTRUCTIONS
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time
and money over the life of your air conditioner. You'll find many answers to common
problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting
Tips first, you may not need to call for service at all.
To prevent injury to the user or other people and property damage, the following
instructions must be followed. Incorrect operation due to ignoring of instructions may
cause harm or damage. The seriousness is classified by the following indications.
WARNING This symbol indicates the possibility of death or serious injury.
CAUTION This symbol indicates the possibility of injury or damage to property.
Always do this.
Never do this.
WARNING
Plug in power plug
properly.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an unspecified power
cord.
Otherwise, it may cause electric
shock or fire due to excess heat
generation.
It may cause electric shock or fire
due to heat generation.
It may cause electric shock or fire.
If the power cord is damaged, it must be replaced by the
manufacturer or an authorised service centre or a similarly
qualified per son in order to avoid a hazard.
Always install circuit
breaker and a dedicated
power circuit.
Do not operate with wet
hands or in damp
environment.
Do not direct airflow at room occupants only.
This could damage your health.
Incorrect installation may cause
fire and electric shock.
It may cause electric shock.
Always ensure effective
grounding.
Do not allow water to run
into electric parts.
Incorrect grounding may cause
electric shock.
It may cause failure of machine
or electric shock.
Unplug the unit if strange
sounds, smell, or smoke
comes from it.
Do not use the socket if it is
loose or damaged.
It may cause fire and electric
shock.
It may cause fire and electric
shock.
Keep firearms away.
Do not use the power cord
close to heating appliances.
It may cause fire.
It may cause fire and electric
shock.
Ventilate room before operating air conditioner if there is
a gas leakage from another appliance.
Do not modify power cord length or share the
outlet with other appliances.
It may cause electric shock or fire due to heat generation.
Do not open the unit during operation.
It may cause electric shock.
Do not use the power cord near flammable gas
or combustibles, such as gasoline, benzene,
thinner, etc.
It may cause an explosion or fire.
Do not disassemble or modify unit.
It may cause failure and electric shock.
It may cause explosion, fire and, burns.
1
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
When the air filter is to be
removed, do not touch the metal
parts of the unit.
It may cause an injury.
Do not use strong detergent
such as wax or thinner but use
a soft cloth.
Appearance may be deteriorated
due to change of product color or
scratching of its surface.
Stop operation and close the
window in storm or hurricane.
Do not put a pet or house plant
where it will be exposed to direct
air flow.
This could injure the pet or plant.
Do not clean the air conditioner
with water.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Operation with windows opened
may cause wetting of indoor and
soaking of household furniture.
When the unit is to be cleaned,
switch off, and turn off the circuit
breaker.
Do not clean unit when power is on
as it may cause fire and electric shock,
it may cause an injury.
Always insert the filters securely.
Clean filter once every two weeks.
Hold the plug by the head of the
power plug when taking it out.
Operation without filters maycause
failure.
It may cause electric shock and
damage.
Ventilate the room well when
used together with a stove, etc.
An oxygen shortage may occur.
Do not use for special purposes.
Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects.It may
cause deterioration of quality, etc.
Ensure that the installation bracket of the
outdoor appliance is not damaged due
to prolonged exposure.
If bracket is damaged, there is
concern of damage due to falling
of unit.
Turn off the main power
switch when not using the
unit for a long time.
It may cause failure of product or
fire.
Do not place obstacles around
air-inlets or inside of air-outlet.
Do not place heavy object on the power
cord and ensure that the cord is not
compressed.
Do not drink water drained
from air conditioner.
It may cause failure of appliance
or accident.
There is danger of fire or electric
shock.
It contains contaminants and
could make you sick.
Use caution when unpacking and
installing. Sharp edges could cause injury.
If water enters the unit, turn the unit off at the power
outlet and switch off the circuit breaker. Isolate
supply by taking the power-plug out and contact a
qualified service technician.
CAUTION
This appliance is not intended for use by persons
(including children) with reduced physical ,sensory
or mental capabilities or lack of experience and
knowledge,unless they have been given supervision
or instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
The appliance shall be installed in accordance
with national wiring regulations.
Do not operate your air conditioner in a wet room
such as a bathroom or laundry room.
The appliance with electric heater shall have at
least 1 meter space to the combustible materials.
Contact the authorised service technician for
repair or maintenance of this unit.
Contact the authorised installer for installation
of this unit.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
NOTE:
The power supply cord with this air
conditioner contains a current detection
device designed to reduce the risk of fire.
Please refer to the section Operation
of Current Device for details.In the event
that the power supply cord is damaged,
it cannot be repaired-it must be replaced
with a cord from the Product Manufacturer.
WARNING
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug.
Do not remove any prong from the power
cord.
Grounding type wall
receptacle
Do not, under any
circumstances , cut,
remove, or byp ass
the gro und ing prong.
Power supply co rd
with 3-pr ong gro unding plug
and current dete ctio n de vice
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WARNING
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your
air conditioner, follow basic precautions, including the following:
Be sure the electrical service is adequate for the model you have chosen. This
information can be found on the serial plate, which is located on the side of the
the cabinet and behind the grille.
If the air conditioner is to be installed in a window, you will probably want to clean
both sides of the glass first. If the window is a triple-track type with a screen panel
included, remove the screen completely before installation.
Be sure the air conditioner has been securely and correctly installed according to
the installation instructions in this manual. Save this manual for possible future
use in removing or installing this unit.
When handling the air conditioner, be careful to avoid cuts from sharp metal fins
on front and rear coils.
WARNING
Electrical Information
The complete electical rating of your new room air conditioner is stated on the
serial plate. Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire
hazards, proper grounding is important. The power cord is equipped with a
three-prong grounding plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the
wall receptacle you intend to use is not adequately grounded or protected by a
time delay fuse or circuit breaker, have a qualified electrician install the proper
receptacle. Ensure the receptacle is accessible after the unit installation.
Do not run air conditioner without side protective cover in place.This could
result in mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
Operation of Cur rent Device
NOTE:
(Applicable to the unit adopts current detection
device only )
The power supply cord contains a current device that senses
damage to the power cord. To test your power supply cord do
the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug
head. Press the TEST button, you will notice a click as the
RESET button pops out.
3. Press the RESET button, again you will notice a click as
the button engages.
4. The power supply cord is now supplying electricity to the
unit. (On some products this it also indicated by a light on
the plug head.)
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for
correct operation.
The power supply must be replaced if it fails reset when
either the TEST button is pushed, or it cannot be reset. A
new one can be obtained from the product manufacturer.
If power supply cord is damaged, it cannot be repaired. It
MUST be replaced by one obtained from the product
manufacturer.
NOTE:This air conditioner is designed to be operated
under condition as follows:
O
Cooling
operation
Outdoor temp:
Indoor temp:
O
O
O
64-109 F/18-43 C (64-125 F/18-52 C
for special tropical models)
O
O
62-90 F/17-32 C
O
23-76 F/-5-24 C
Heating Outdoor temp:
operation Indoor temp:
32-80OF/0-27 C
Note: Performance may be reduced outside of these
operating temperatures.
O
O
3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
BEFORE YOU BEGIN
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Read these instructions completely
and carefully.
IMPORTANT- Save these
instructions for local inspector s use.
IMPORTANT- Observe all
governing codes and ordianaces.
Note to Installer- Be sure to leave these
instructions with the Consumer.
Note to Consumer- Keep these
instructions for futrue reference.
Skill level- Installatio of this appliance
requires basic mechanical skills.
Completion time- Approximately 1 hour.
We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
You MUST use all supplied parts and use
proper installation procedures as described
in these instructions when installing this air
conditioner.
Do not change the plug on the power cord
of the air conditioner.
Aluminum house wiring may present special
problems- consult a qualified electircian.
When handling unit, be careful to avoid cuts from
sharp metal edges and aluminum fins on front and
rear coils.
TOOLS YOU WILL NEED
Screwdriver
Level
TOOLS YOU MAY USE
WINDOW REQUIREMENTS
Screwdriver
Your air conditioner is designed to install in
standard double hung windows with opening
widths of 23 to 36 inches(584mm to 914mm) .
Ruler or tape measure
Scissors or knife
INNER
WINDOW SILL
INTERIOR
WALL
NOTE:
Wooden Windows
Save Carton and these Installation Instructions
for future reference. The carton is the best way
to store unit during winter, or when not in use.
Table 1
4
INSTALLATION INSTRUCTIONS
C: A lign the hole in the top rail with those in the top
of the unit as shown in Fig.B
PREPARE THE WINDOW
Lower sash must open sufficiently to allow a clear
vertical opening of 13 inches (330mm). Side louvers
and the rear of the AC must have clear air space to
allow enough airflow through the condenser, for heat
removal. The rear of the unit must be outdoors, not
inside a building or garage.
Fig.B
Mounting Hardware
D: Secure the top rail to the unit with the 3/8 S crews
as shown in Fig.C.
3/4 (or 1 / 2 ) Lock Frame Sash Lock Window sash
Screws
(1)
seal fo am
(2)
(7)
(1)
F ig.C
PREPARE AIR CONDITIONER
A: Remove the air conditioner from the carton and
place on a flat surface.
NOTE: For safety reasons, all four(4) screws M UST
be securely fastened.
B: Remove top rail from the rear of the packaging
material as shown in Fig. A.
Top Rail Hardware
or
3/8 Screws
(4)
Top Rail
(1)
INSTALL THE ACCORDION PANELS
NOTE: Top rail and Sliding Pan els at ea ch side are
offset to provide the prop er pitch to th e rear of (5 /1 6 ).
This is n ecessary for prope r cond ensed w ater
utiliza tion and dr ainage. If you are not u sing the Side
Pan els for any reaso n, th is pitch to the r ear must b e
maintained.
Fig.A
A.Place unit on floor, a bench or
a table. Hold the Accordion
Panel in one hand and gently
pull back the center to free the
open end. See Fig.1
Top R ail
Packaging
Fig.1
5
INSTALLATION INSTRUCTIONS
B. Slide the free end " Ⅰ" section of the panel directly
into the cabinet as shown in Fig. 2. Slide the panel
down. Be sure to leave enough space to slip the
top and bottom of the frame into the rails on the
cabinet.
SECURE THE ACCORDION PANELS
A.Keep a firm grip on the air conditioner, carefully
place the unit into the window opening so the bottom
of the air conditioner frame is agains t the window
sill (Fig.5). Carefully close the window behind the top
rail of the unit.
Measure from the cabinet edge
"Ⅰ"s ection
About 5/8 to 3/4
INSIDE
OUTSIDE
Wooden Windows
Fig.5
Fig.2
NOT E: Check that air conditioner is tilted back about
5/8 to 3/4 (tilted about 3 O to4 Odownward tothe outside).
After proper installation, condensate should not drain
from the overflow drain hole during normal use, correct
the slope otherwise.
C. Once the panel has been installed on the side of
the cabinet, make sure it sits securely inside the
frame channel by making slight adjustments.
Slide the top and bottom ends of the frame into the
top and bottom rails of the cabinet. Fig.3.
B.Extend the side panels out against the window
frame (Fig.6).
Top Rail
window
frame
Fig.6
Bottom Rail
Fig.3
INSTALL SUPPORT BRACKET
D. Slide the panel all the way in and repeat on the
other side.
Fig.4
Top Rail
A.Place the frame lock between the frame
extensions and the window sill as shown(Fig.7).
Drive 3 / 4 " (19mm)or 1 / 2 "(12.7mm) locking screws
through the frame lock and into the sill .
Top right
Top left
NOTE : To prevent window sill from s plitting,drill
1 / 8" (3mm) pilot holes before driving screws.
Bottom Rail
NOTE: If storm window blocks AC, see Fig. 11.
Fig.7
6
INSTALLATION INSTRUCTIONS
B.Drive 3/4" (19mm) or 1/2" (12.7mm) locking
screws through frame holes into window sash (Fig.8).
If AC is Blocked by Stor m Window
Add wood as shown in Fig.11, or remove storm
window before air conditioner is installed.
If Storm Window Fram e must rem ain, be sure the
drain holes or slots are not caulked or painted shut.
Accumulated Rain Water or Condensation must be
allowed to drain out.
Removing AC From Window
Turn AC off, and disconnect power cord.
Remove sash seal from between windows, and
unscrew safety sash lock.
Remove screws installed through frame and framelock.
Close (slide) side panels into frame.
Keeping a firm grip on air conditioner, raise sash
and carefully remove.
Be carefully not to spill any rem aining water while
lifting unit from window. Store parts WITH air
conditioner.
Fig.8
C.To secure lower sash in place, attach right angle
sash lock with 3/4" (19mm) or 1 /2" (12.7mm) screw as
shown(Fig.9).
SASH
Fig.9
Storm window
frame or other
obstruction.
D.Cut Window sash seal foam and insert it in the
space between the upper and lower sashes (Fig.10).
1-1/2"min
(38 mm)
FOAM SEAL
Fig.11
Fig.10
7
Board
thickn ess
as req uire d,
for pr oper
pitch to rea r,
along entir e
sill. F asten
with n ails o r
screw s.
NORMAL SOUNDS
High Pitched Chatter
High efficiency compressors
may h ave a high pitched chatt er
during the cooling cycle.
Vibratio n
Unit may v ibrate and make noise
because of poor wall or window
constructio n or incorrect installation.
Soun d of R ushing Air
At the front of the unit, you m ay
hear the sound o f rushing air
being moved by t he fan
P inging or Sw itchin g
Droplets of water hit ting condens er
during normal operation may cau se
pinging or switching sounds.
Gurgle /Hiss
Gurgling or hissing noise may
be heard due to refrig erant
passing through evaporator
during normal operation.
NOTE:
All the illustrations in this manual are for explanation purpose only. Your air
conditioner may be slightly different. The actual shape shall prevail.
AIR CONDITIONER FEATURES
ELECTRONIC CONTROL OPERATING INSTRUCTIONS
Before you begin, thoroughly familiarize yourself with the control panel as shown below and all its
functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit
control alone or with the remote.
TO TURN UNIT ON OR OFF:
Press
ADJUSTS
TEMPERATUR E
OR TIME
Temp
Temp
Timer
Timer
On
ACTIVATES
TIMER
Sleep
SLEEP MO DE
Timer
CHECK FILTER
RESET BUTTON
ADJUS TS
TEMPE RATURE
OR TIM E
DISPL AYS
TEMP ERATURE
OR TI ME OR ERROR CODES
Off
Che ck
Filter
A uto
Auto
Cool
Low
Dry
M ed
Fan
H igh
TO CHANGE TEMPERATURE SETT ING:
Press
/ UP/DOWN button to change
temperature setting.
SET FAN SPEED
SETS MODE
Mode
Fan
E NERGY
S AVER MODE
NOTE:Press or hold either UP( ) or DOWN ( ) button
until the desired temperature is seen on the display.
This temperature will be automatically maintained
anywhere between 62 OF(17 OC) and 86 OF(30 OC). If
you want the display to read the actual room
temperature, see To Operate on Fan Only section.
Follow Me indicator
(on so m e models)
TURNS U NIT
ON OR OF F
Energ y
Saver
ON/OFF button to turn unit on or off.
NOTE:Th e u ni t w i ll i ni ti a t e automatically the Energy
Saver function under Cool, Dry,Auto(only Auto-Cooling
and Auto-Fan) modes.
Fo ll ow
Me
On/Off
UNIT CONTROL
8
AIR CONDITIONER FEATURES
TO ADJU ST FAN SPEEDS:
TO SELECT THE OPERATING MODE:
Press to select the Fan Speed in four steps-Auto,
Low, Med or High. Each time the button is pressed,
the fan speed mode is shifted. On Dry mode,the fan
speed is controlled at Low automatically.
To choose operating mode, press
Mode button.Each
time you press the button, a mode is selected in a
sequence that goes from Auto, Cool, Dry and Fan. The
indicator light beside will be illuminated and remained
on once the m ode is selected.
The unit will initiate automatically the Energy S aver
function under Cool, Dry, Auto(only Auto-Cooling and
Auto-Fan) modes.
SLEEP FEATU RE:
Press
Sleep button to initiate the sleep mode. In
this mode the selected temperature will increase by
O
O
2 F/1(or 2) C 30 minutes after the mode is selected.
O
The temperature will then increase by another 2 F/
O
1(or 2) C after an additional 30 minutes. This new
temperature will be maintained for 6 hours before it
returns to the originally selected tem perature. This
ends the S leep mode and the unit will continue to
operate as originally programmed. The Sleep mode
program can be cancelled at any time during
operation by pressing the Sleep button again.
To operate on Auto feature:
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling only models
without), or fan only operation depending on what
temperature you have selected and the room temperature.
The air conditioner will control room temperature
automatically round the temperature point set by you.
In this mode, the fan speed cannot be adjusted, it starts
automatically at a speed according to the room
temperature.
To operate on Fan Only:
CH ECK F ILTER FEATURE:
Use this function only when cooling is not desired,such
as for room air circulation or to exhaust stale air(on
some models). (Remember to open the vent during this
function, but keep it closed during cooling for maximum
cooling efficiency.) You can choose any fan speed you
prefer.
During this function, the display will show the actual
room temperature, not the set temperature as in the
cooling mode.
In Fan only m ode ,the temperature is not adjusted.
Press
Check filter button to initiate theis feature.
This feature is a reminder to clean the Air Filter for
more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after
cleaning the filter, press the Check Filter button and
the light will go off.
ENERGY SAVER FEATURE:
Press Energy saver button to initia te this function.
This fu nction is availa ble on COO L, DRY, AUTO
(only AUTO-COOLING and AUTO-FAN) modes.The
fan will continue to run for 3 minute s after the
compressor shu ts off.The fan then cycles on for 2
minutes at 10 minute intervals un til the roo m
temperature is above the set temperature, at wh ich
time th e compre ssor turns ba ck on and Cooling
Starts.
To operate on Dry mode:
In this mode, the air conditioner will generally operate
in the form of a dehumidifier. Since the conditioned
space is a closed or sealed area, some degree of
cooling will continue.
TIMER: AUTO START/STOP FEATURE:
When the unit is on or off, first press
Timer button, the
TIMER ON indicator light illuminates. It indicates the Auto
Start program is initiated.
When the time of TIMER ON is displayed ,press the Timer
button again, the TIMER OFF indicator light illuminates.
It indicates the Auto Stop program is initiated.
Press or hold the UP or DOWN button to change the Auto
time by 0.5 hour increments, up to 10 hours,then at 1 hour
increments up to 24 hours.The control will count down the
time remaining until s tart.
The selected time will register in 5 seconds, and the system
will automatically revert back to display the previous
temperature setting or room temperature when the unit is
on.(when the unit is off,there is no display.)
Turning the unit ON or OFF at any time or adjusting the
timer setting to 0.0 will cancel the Auto Start/Stop timed
program.
FO LLOW ME F EATU RE: (on so me mo dels )
Light flashing
En ergy
Sav er
Follow
Me
On/Off
This feature can be ac tivated from the re mote
control ONLY. The remote control se rve s as
a remote thermostat a llowing for the precise
te mpera ture control at its loc ation.
To activate the Follow Me feature, point the remote
control tow ards the unit and press the Follow Me
button. T he remote dis play is actual temperature at
its location. The remote control will send this signal
to the air conditioner every 3 minutes interval until
press the Follow Me button again. If the unit does not
receive the Follow Me signal during any 7 minutes
interval, the unit will beep to indicate the Follow Me
mode has ended.
9
AIR CONDITIONER FEATURES
Air Directional Louvers
DISPLAYS:
Temp
Temp
Time r
Timer
Displays
Air Dir ectio nal Louve rs
DISPLAYS:
O
Lever
O
Shows the set temperature in " C " or " F " and the
Auto-timer settings.While on Fan only mode,it shows
the room temperature.
Error codes:
A S-Room temperature sensor error-Unplug the unit
and plug it back in.If error repeats, call for service.
NOTE:In Fan only mode,it will display " LO " or " HI " .
- E vaporator temperature sensor error-Unplug the
unit and plug it back in.If error repeats, call for
servi ce.
NOTE: " " is displayed as s hown in the left picture.
HS - El ec tric heating sensor error-Unplug the unit and
plug it back in.If error repeats, call for service.
Air Direction
The louvers will allow you to direct the air flow Left or
Right throughout the room as needed.
Move the Levers from side to side until the desired
Left/Right direction is obtained.
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure,
here are more features in your control that you should
become familiar with.
The Cool circuit has an automatic 3 m inute time
delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and
possible circuit breaker tripping.The fan will
continue to run during this time.
The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius. To convert
from one to the other, press and hold the Left and
Right Temp/Timer buttons at the same time, for 3
seconds.
NOTE:
If the unit breaks off unexpectedly due to the power
cut, it will restart with the previous function setting
automatically when the power resumes.
CARE AND CLEANING
Air Filter Cleaning
CAUTION
Clean your air conditioner occasionally to keep it looking
new. Be sure to unplug the unit before cleaning to
prevent chock or fire hazards.
Air Filter Cleaning
The air filter should be checked at least once a month to see
if cleaning is necessary. Trapped particles in the filter can
build up and cause an accumulation of frost on the cooling
coils.
10
CARE AND CLEANING
Cabinet Cleaning
Air Filter Cleaning
Remove the filter by sliding out from the right-hand side.
Wash the filter using liquid dishwashing detergent and warm
water. Rinse filter thoroughly. Gently shake excess water
from the filter. Be sure the filter is thoroughly dry before
replacing. Or, instead of washing you may vacuum the filter
clean.
。
。
Note: Never use hot water over 40 C(104 F) to clean the
air filter. Never attempt to operate the unit without the air
filter.
Be sure to unplug the air conditioner to prevent shock or fire
hazard. The cabinet and front may be dusted with an oil-free
cloth or washed with a cloth dampened in a solution of warm
water and mild liquid dishwashing detergent. Rinse thoroughly
and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping
around the controls. Excess water in or around the controls
may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter,
remove it carefully from the window according to the
installation instructions. Cover it with plastic or return it to
the original carton.
TROUBLESHOOTING TIPS
Before calling for service, review this list. It may save your time and expense. This list includes common
occurrences that are not the result of defective workman-ship or materials in this appliance.
Problem
Solution
Air conditioner
does not start
Wall plug disconnected. Push plug firmly into wall outlet.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or
reset circuit breaker.
Plug Current Device Tripped. Press the RESET button.
Power is OFF. Turn power ON.
Air from unit does
not feel cold
enough
Room temperature below 62OF(17OC ). Cooling may not occur until room temperature
O
O
rises above 62 F(17 C).
Temperature sensing behind air filter element touching cold coil. Keep it from the cold
coil.
Set to a Lower temperature.
Compressor stopped when changing modes. Wait for 3 minutes after set to the COOL
mode.
Air conditioner
cooling, but room
is too warm- ice
forming on cooling
coil behind
decorative front.
Outdoor temperature below 64OF(18OC). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost,
set to FAN ONLY mode.
Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLY
mode. Then, set temperature to a Higher setting.
11
TROUBLESHOOTING TIPS
Problem
Air conditioner
cooling, but room
is too warm- NO
ice forming on
cooling coil behind
decorative front.
Solution
Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too High, set temperature to a Lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution.
Clear blockage in front of unit.
Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers.
Unit recently turned on in hot room. Allow additional time to remove Stored heat from
walls, ceiling, floor and furniture.
Air conditioner turns on
and off rapidly
Noise when unit is
cooling
Dirty air filter- air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past
cooling coils more frequently.
Air movement sound. This is normal . If too loud, set to a slower FAN setting.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Water dripping
INSIDE when
unit is cooling.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage.
Refer to installation instructions - check with installer.
Water dripping
OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during
excessively humid days.
Remote Sensing
Deactivating
Prematurely
(some models)
Room too cold
Remote control not located within range. Place remote control within 20 feet & 180 ,
radius of the front of the unit.
Remote control signal obstructed. Remove obstruction.
Set temperature too low. Increase set temperature.
12
AIR CONDITIONER WARRANTY
One
ONE-YEAR
1-866-646-4332
13
The design and specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.
Manual del Usuario
INSTRUCCIONES IMPORTANTES DE LA SEGURIDAD
WARNING
Temperatura
fuera
Temperatura
interior:
Temperatura
fuera
Temperatura
interior:
INSTRUCCIONES DE INSTALACIÓN
HEERAMIENTOS QUE NECESITE
Approximadamente 1 horas.
HERRAMIENTOS QUIZÄ NECESITE
REQUISITOS DE LA VENTANA
Lápiz
Acodo
Regla o cinta métrica
EXTERIOR
PARED
DENTRO CERCA
VENTANA umbral
NOTA:
INTERIOR
PARED
VENTANA DE MADERA
Tabla 1
3/4” (or 1/2” )
Tornillos
(7)
Carril superior
(1)
Embalaje
Carril superior
Aproxima 5/8” a 3/4''
DENTRO
VENTANA DE MADERA
FUERA
Carril superioro
Carril inferior
Carril superior
Derecha superior
Hoja
NOTA:
Ajuste la
temperatura
o reloj
Receptor del
signo del remoto
ndicator de Seguirme
ENERGY
SAVER MODE
CONTROL DE LA UNIDAD
CARACTERÍSTICAS DEL AIRE ACONDICIONADO
PARA MODIFICAR LA VELOCIDAD DEL VENTILADOR
A elegir el modo operativo:
FUNCIÓN DURMIENTA:
On/Off
RELOJ: FUNCIÓN DE AUTO EMPEZAR O TERMINAR:
CARACTERÍSTICAS DEL AIRE ACONDICIONADO
Pantallas:
PANTALLAS:
MANTENIMIENTO Y LIMPIEZA
CAUTION
Limpieza del Filtro de Aire
La Limpieza del Gabinete
GARANTIA DE AIR ACONDICIONADO
MIDEA , A TRAVES DE SU
CENTRO DE SERVICIO
RESPONSABLE PARA
GARANTIA
costos
de
o
dispositivo
que
EL CONSUMIDOR VA A SER
se
de
servicio
que
se
bajo
RESPONSABILIDADES
DEL
CONSUMIDOR NORMALES
13
GARANTIA DE AIR ACONDICIONADO
1-866-646-4332.
14