Black & Decker RTX-1, RT5100, RTX, RTX-2, RTX-4, RTX-6, RTX-3, RTX-B Bedienungsanleitung

condition that may affect the tool’s operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
SERVICE
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
INSTRUCTION MANUAL
6
5
4
Catalog Number RTX
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-54-HOW-TO (544-6986)
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PURCHASE,
CALL 1-800-54-HOW-TO (1-800-544-6986).
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
KEY INFORMATION YOU SHOULD KNOW:
• Do not tighten the collet nut without an accessory bit in place.
• Do not engage spindle lock until tool has come to a complete stop.
SAVE THIS MANUAL FOR FUTURE REFERERENCE.
• Accessories must be rated for at least the speed recommended on the tool warning
label. Wheels and other accessories running over rated speed can fly apart and cause
injury.
The label on your tool may include the following symbols.
V ..........................volts
A..........................amperes
Hz ........................hertz
W ........................watts
min ........................minutes
......................alternating current
no ........................no load speed
......................direct current
..........................Class II Construction
........................earthing terminal
........................safety alert symbol
.../min ..................revolutions or
reciprocations
per minute
ADDITIONAL SAFETY RULES F0R ROTARY TOOLS
ALWAYS WEAR EYE PROTECTION WHEN USING THIS TOOL!
• If accessory jams, turn tool off and disconnect from power supply before freeing
accessory from the jam.
• Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live” and shock the operator.
• When using cutoff wheels always have the work securely clamped. Never attempt to
hold the work with one hand while using any cutting accessory.
• Keep hands away from rotating accessories.
• Allow accessories and collets to cool before touching with bare hands. They will be
hot after using.
• Insure there are no foreign objects in the workpiece such as nails which if hit could
cause loss of control of unit.
• Always feed the cutter into the material in the same direction as the chips are being
thrown. Feeding the tool in the wrong direction can cause loss of control.
• Keep handles dry, clean, free from oil and grease. This will enable better control of the
tool.
• When cutting wood, extra care should be taken to avoid inhalation and minimize skin
contact.
• Wear ear protection. Noise level may be amplified when using tool in enclosed spaces.
• The RTX has an internal speed control, never use an external speed control on this
unit.
• Do not use worn accessories.
• Do not use grinding wheels that have cracks.
• When turning tool on, hold it away from your face, since a damaged accessory
could come apart.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
CAT. NO. RTX
FORM NO. 397438-00
1
Copyright©2000 Black & Decker (JUNE 00 -1) PRINTED IN CHINA
2
WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
On/Off Switch
Interrupteur
Interruptor de encendido y
apagado
SAVE THESE INSTRUCTIONS
6
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust
or fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
5
4
3
ELECTRICAL SAFETY
• Double Insulated tools are equipped with a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do not change the plug in any way. Double
Insulation
eliminates the need for the three wire grounded power cord and grounded
power supply system.
• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
• Don’t expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
• When operating a power tool outside, use an outdoor extension cord marked "W-A"
or "W". These cords are rated for outdoor use and reduce the risk of electric shock.
6
Spindle
Arbre
Flecha
On/Off Switch
Interrupteur
Interruptor de encendido y apagado
5
6
4
5
4
5
6
Tool Hanger
Douille de serrage
Pinza portapiezas
6
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal
injury.
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
is left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
5
4
Flexible Shaft
Arbre flexible
Eje flexible
7
6
5
4
TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
4
8
9
6 " (150mm)
150 mm 6 po
150 mm (6 pulg.)
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
USE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using. Always use the proper size
extension cords with the tool – that is, proper wire size for various lengths of cord and heavy
enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. For proper size cords see chart
below.
Volts
120V
240V
Ampere
More
Than
0
6
10 12 -
Minimum Gage for Cord Sets
Total Length of Cord in Feet
0-25
26-50
51-100
101-150
0-50
51-100 101-200
201-300
Rating
Not more
Than
6
18
10
18
12
16
16
14
American Wire Gage
16
16
16
12
16
14
14
12
14
12
Not Recommended
SPINDLE LOCK LEVER
TURN OFF AND UNPLUG TOOL FROM POWER SUPPLY.
Fig.1 shows the ON/OFF switch and the spindle lock lever. To lock the spindle for changing
accessories, pull back on the spindle lock lever as shown in Figure 2. With the lever in the full
back position the spindle will lock. Install or remove the accessories as directed in this
manual. Release the spindle lock lever and you’re finished.
ON/OFF SWITCH
To turn the tool ON, slide the switch button forward. The tool will immediately run at the speed
which is selected. Do not attempt to start tool with spindle lock engaged. It will not run.
SPEED SELECTION
To operate the tool, select the speed setting you wish with the speed wheel, shown in Fig 3,
and slide the ON/OFF switch forward. The speed setting can be adjusted either with the tool
on or off.
CAUTION: Because the RTX has a separate speed wheel for setting the speed (8,000 30,000 RPM), the tool will start at the speed where the speed wheel is set. Be sure switch is
fully OFF before plugging in.
The numbered positions,1 through 6 inscribed on the switch speed wheel, do not indicate
any precise speed but are good reference points. The higher the number, the higher the tool
speed.
The approximate speed at each setting is:
SPEED SETTING
APPROX. SPEED
1
2
3
4
5
6
8,000 12,000 19,000 24,000 28,000 30,000
(Actual RPM’s on your tool may vary.)
Be sure to select the proper speed for your rotary tool operation. The following chart
provides a speed guide for various operations.
If in doubt about the proper speed for your operation, test the performance at low speed
settings and gradually increase until a comfortable speed is found.
Cutting Metal . . . . . 5-6
Deburring . . . . . . . 4-5
Sanding Wood . . . . 5-6
Stripping Metal . . . 4-5
Sharpening. . . . . . . 3-5
Engraving Metal . . 4-5
Polishing . . . . . . . . 1-2
Drilling Holes. . . . . 4-5
Removing Rust. . . . 1-2
CAUTION: Never exceed the speed rating of the accessory being used.
CHANGING ACCESSORIES
Accessories are held in place by a collet and collet nut as shown in Figure 4.
To insert an accessory:
1. Turn off tool, allow it to come to a complete stop and disconnect from the power supply.
2. Pull back on the spindle lock lever (see Fig. 2) and grasp the collet nut.
3. Turn the collet nut counter-clockwise as shown in Fig. 5 until it is loose.
4. Insert the new accessory into the collet as far as it will go.
5. Tighten (clockwise) the collet nut securely. NOTE: The collet was designed to be hand
tightened and loosened only. Accessories naturally self tighten during use. A wrench is
provided with the tool for loosening. You should never need to tighten the collet nut with
the wrench. If a wrench is needed, use only the wrench provided. Do not use tools that
will mar the finish and could break the collet. Always ensure there is some accessory in
the collet before tightening. Tightening an empty collet can crack it.
6. Release the spindle lock lever and you’re finished.
7. If an accessory causes vibration it can usually be improved by loosening the collet nut,
pushing the accessory in as far as it will go and rotating it 1/4 turn then retightening the
collet.
CHANGING THE COLLET
Some accessories require different sized collets. The two collets used with Black & Decker
accessories are 1/8" (used for most accessories) and 3/32". Ensure your collet size
matches your accessory.
To change the collet:
1. Turn off tool, allow it to come to a complete stop and disconnect from power supply.
2. Pull back on the spindle lock lever (see Fig. 2) and grasp the collet nut.
3. Turn the collet nut counter-clockwise and remove the collet nut and the collet from the
threaded spindle (see Fig. 4).
4. Insert the new collet into the spindle.
5. Screw on the collet nut.
6. Release the spindle lock.
USING THE ROTARY TOOL
WARNING: Always wear eye protection.
When operating the tool be sure to hold it securely. For detail work, grip the contoured area
at the front of the tool, near the spindle. Before beginning a project, practice using the tool
on some scrap material until you get the "feel" of the tool. The rotary tool is small and easy to
use but don’t be fooled; it’s a real power tool and should be handled carefully and properly
as described in this manual. Don’t overload the tool. Performance is enhanced by letting the
tool do the work.
FLEXIBLE SHAFT RT5100 FLEXIBLE ROTARY TOOL EXTENDER
(Available as a separate accessory and included with catalog number RTX-2 only)
FLEXIBLE SHAFT INSTALLATION INSTRUCTIONS
1. Turn off tool, allow it to come to a complete stop and disconnect from power supply.
2. Remove the collet nut and collet from the tool by first pulling back on the spindle lock
lever and grasping the collet nut (Fig.2).
3. Turn the collet nut counter-clockwise and remove the collet nut and the collet from the
threaded spindle (see Fig. 4).Release the spindle lock.
4. Remove the silver housing cap (Fig.4) by turning counterclockwise.
5. Locate the driver nut and thread it onto the motor shaft (Fig. 6).
6. Screw the FLEXIBLE SHAFT onto the rotary tool as shown in Fig. 7 insuring that the rotating
center core engages the square hole socket in the driver nut (Fig. 7). NOTE: Use caution
when screwing the metal housing of the shaft onto the threaded portion of the rotary tool.
Avoid cross threading.
7. The FLEXIBLE SHAFT is now ready for use. To insert an accessory, Turn off tool, allow it to
come to a complete stop and disconnect from power supply. Place the provided lock pin
into the opening in the FLEXIBLE SHAFT hand piece and rotate collet nut until lockpin
engages hole in spindle (Fig. 8). With the shaft locked, turn the collet nut counter-clockwise to loosen. Insert the accessory completely into the collet to avoid wobbling. Tighten
collet nut securely by hand. Remove lock pin.
8. The Flexible Shaft collet can be changed as described in the “Changing the Collet” section.
IMPORTANT: Avoid using the Flexible Shaft with a sharp bend as shown in Fig. 9. A radius
of 6" or larger is recommended. A tool hanger (Fig. 4) is provided to hang the tool when using
the flex shaft. The hanger secures the tool and helps avoid sharp bends on the flex shaft.
NOTE: The rotating center core can come out of the FLEXIBLE SHAFT. This is not a problem.
Simply reinsert it into the FLEXIBLE SHAFT. If the center core gets dirty, wipe it off and apply a
very light film of high temperature grease. The square drive of the center core may not
engage the hand piece. To get it to engage, apply a light force to the tip of the center core
while rotating the handpiece collet nut.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service organizations, always using identical replacement
parts. Unit contains no user serviceable parts inside.
ACCESSORIES
Black & Decker offers a large selection of accessories available at your local dealer or
authorized service center at extra cost. Only Black & Decker accessories are recommended
for use in the RTX or B&D Flexible Shaft.
If you need assistance regarding accessories, please call: 1-800-54-HOW TO (544-6986).
CAUTION: Use only those accessories rated at 30,000 RPM or greater. Exception: Do
not operate wire brushes, bristle brushes, diamond dome sander, or 1-1/4” diamond wheels
at speeds greater than 15,000 RPM (speed setting #2). Never exceed the speed rating of the
accessory being used.
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under "Tools–Electric"
or call: 1-800-54-HOW TO (544-6986).
FULL FIVE-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for five years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under
"Tools–Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center.
NOTE: This tool is designed, manufactured and tested to meet or exceed the needs of the
do-it-yourselfer in the execution of projects and repairs in and around the home. With proper
use it will provide the home owner with years of service. However, if you use tools for a living
and use this product or any of Black & Decker’s other Consumer Home Use tools ON THE
JOBSITE you should know that they CANNOT BE COVERED UNDER OUR WARRANTY.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
GUIDE D’UTILISATION
Modèle RTX
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAISON PRIÈRE DE COMPOSER
CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
•
•
•
•
•
Tension
120 V
240 V
De 0 à 25
De 0 à 50
Calibre moyen de fil (AWG)
18
18
16
14
16
16
16
12
1
8,000
5-6
5-6
3-5
1-2
1-2
4-5
4-5
4-5
4-5
INFORMACIÓN CLAVE QUE SE DEBE SABER:
REGLAS ADICIONALES DE SEGURIDAD PARA HERRAMIENTAS
ROTATORIAS
¡SIEMPRE USE PROTECCIÓN PARA LOS OJOS CUANDO USE ESTA HERRAMIENTA!
ANTES DE DEVOLVER ESTE PRODUCTO POR CUALQUIER
RAZON POR FAVOR LLAME
5-6
5-6
3-5
1-2
1-2
4-5
4-5
4-5
4-5
BLACK & DECKER S.A. DE C.V.
BOSQUES DE CIDROS ACCESO RADIATAS NO. 42
COL. BOSQUES DE LAS LOMAS.
05120 MÉXICO, D.F
TEL. 3-26-71-00
120 V~
223 W
60 Hz
2A">