advertisement
▼
Scroll to page 2
Wireless TV CONNECT Quick Setup Before You Begin With HP Wireless TV Connect, you can wirelessly stream high-definition multimedia content from your computer to your home entertainment center. Before setup, note the following configuration requirements: •Your computer must have an available HDMI port and an available USB port. 1 Connect the USB power cable to the PC adapter, and then connect the PC adapter and the USB power cable to the computer. NOTE: The location of the computer ports may vary. 2 Connect the TV adapter to your TV or other external display and to external power. 3 If you connected to a TV, press the input source button on the TV to select the HDMI input. When the components are connected correctly and the correct source is selected, the image on the computer display will be shown on the TV. NOTE: Make sure that your computer and TV are both powered on. NOTE: If the PC adapter light does not turn on after inserting the adapter into the HDMI port on the computer, pull it out and reinsert it. NOTE: If you are using an external display other than a TV, the display may not have an input source input button and the source may cycle automatically. NOTE: It may take a few seconds for the adapters to link to each other and for the image on the computer to display on the TV (or other external display). •Your TV (or other external display) must have an available HDMI port. NOTE: If the HDMI port on your TV is occupied with another device, consider using an HDMI switch purchased separately from an electronics retailer. •For optimal performance, locate the TV adapter no further than 5 m (16.4 ft) from the PC adapter. Troubleshooting PC Adapter TV Adapter 1 HDMI connector: Connects the PC adapter to your computer. 2 Link light • On: The adapter is linked to the TV adapter. • Blinking: The adapter is attempting to link to the TV adapter. 3 USB connector: Connects the USB power cable to the PC adapter. 4 Reset button* *The reset button on the PC adapter is used only during a software upgrade, along with the Micro USB power port on the TV adapter. NOTE: You may need to upgrade the software on your adapter to ensure compatibility with devices produced by other manufacturers. When it’s available, you can download updated software with installation instructions from http://www.hp.com/support. Cables 1 Power adapter and cable: Connects the TV adapter to external power. 1 2 HDMI cable: Connects the TV adapter to your TV or other external display 3USB cable: Connects the PC 2 adapter to your computer. IssueResolution 1 Up button: Scrolls up through menu. 2 Down button: Scrolls down through menu. 3 Menu/Select button: Displays the Setup menu* and selects items. 4 HDMI port: Connects the TV adapter to your TV or display. 5 Micro USB power port: Connects the TV adapter to external power, and can also be used to upgrade the HP Wireless TV Connect firmware. 6 Link light • Blinking blue: The TV adapter is attempting to link to the PC adapter. • Solid white: The TV adapter is linked to the PC adapter. 7 Power light • On: The adapter is on. • Off: The adapter is off. *The Setup menu allows you to add or remove a video source, modify a video source name, disconnect a wireless link, and exit the menu. To add or remove a video source, or disconnect a wireless link: 1. Press the Menu button twice. 2. Press the Down or Up button to highlight Add or Remove Video Source or Disconnect Wireless Link. 3. Press the Menu button to select the item and execute the process. 4. Press the Menu button again to confirm adding or removing a video source, or disconnecting a wireless link. NOTE: To add a new video source after removing one, repeat the above process. •Plug another device into the wall outlet to ensure that the outlet is functioning. The link light on the TV adapter does not turn on. •Ensure that the HDMI cables are securely connected to the components. The link light turns on but continues to blink. •Wait a few minutes for the components to complete initialization. You should see messages on the computer and/or TV screen. It may take up to 5 minutes for initialization to complete. •Ensure that you have connected the components according to the instructions. The TV does not display the image that is on the computer. •Press the input source button on the TV to select the HDMI input. Nothing happens when I press the Reset button on the PC adapter. •The Reset button on the PC adapter is only used for software upgrades. Canada notices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. The device complies with Industry Canada license-exempt RSS standard(s). Wireless operation is subject to 2 conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user’s authority to operate the equipment. Cables To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods. Declaration of Conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference received, including interference that may cause undesired operation. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15 to 5.25 GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage to this device. The antennas for this device are not replaceable. Any attempt at user access will damage your computer. AC adapter notices WARNING! To reduce the risk of electric shock or damage to the equipment: •Plug the AC adapter into an AC outlet that is easily accessible •Disconnect power from the product by unplugging the AC adapter from the AC outlet (not by unplugging the AC adapter from the product). WARNING! To reduce potential safety issues, only the AC adapter provided with the product, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the product. Wireless Antennas The wireless antennas transmit signals from the PC adapter to the TV adapter. These antennas are not visible from the outside of the adapters. If you have questions about the product that are not related to this declaration, write to: Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, TX 77269-2000 For questions regarding this FCC declaration, write to: NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions. Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, TX 77269-2000 To identify your product, refer to the part, series, or model number located on the product. This device must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebook computers. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. © Copyright 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical and editorial errors or omissions contained herein. First Edition: September 2011 CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to cochannel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85- GHz bands. These radar stations can cause interference with and/or damage to this device. Replace this box with PI statement as per spec. In some environments, the use of wireless devices may be restricted. Such restrictions may apply in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. 663694-001 9/1/2011 4:34:08 PM Product: Wireless HDMI Document: Consumer QSP •Ensure that the power adapter is securely connected to the TV adapter and to a wall outlet. Federal Communications Commission notice or call HP at 281-514-3333 To modify the video source name: 1. Press the Menu button twice. 2. Press the Down button to highlight Modify Video Source name. 3. Press the Menu button to execute the naming process. 4. Press the Menu button to select the video source to be renamed. 5. Use the Up or Down buttons to move horizontally and highlight the character to be changed. 6. Press the Menu button to select the character to be changed. 7. Press the Up or Down buttons to change the character. 8. Press the Menu button to select the new character. 9. Press and hold the Menu button to select Save or Exit Video Source name. NOTE: You may need to upgrade the software on your adapter to ensure compatibility with devices produced by other manufacturers. When it’s available, you can download updated software with installation instructions from http://www.hp.com/support. 663694-001 Barbossa_v32.indd 1 The power light on the TV adapter does not turn on. After the Save or Exit function has been selected, the display returns to the main menu. 3 Regulatory and Safety Notices Part number: 621361-001 Color page 1: CMYK + PMS 640 Flat size: 27.5 x 17 Color page 2: CMYK + PMS 640 Finished size: 5.5 x 8.5 Fold 1: Horizontal, in half Fold 2: 5-panel accordion English on front (outside) English on front (outside) 6620 Cypresswood Drive Suite 120 Spring, TX 77379 832.717.4331 CONNECTEUR TV SANS Installation rapide 1 2 3 1 2 Avis Canadien 3 663694-001 Barbossa_v32.indd 2 9/1/2011 4:34:19 PM Product: Wireless HDMI Document: Consumer QSP Part number: 621361-001 Color page 1: CMYK + PMS 640 Flat size: 27.5 x 17 Color page 2: CMYK + PMS 640 Finished size: 5.5 x 8.5 Fold 1: Horizontal, in half Fold 2: 5-panel accordion English on front (outside) English on front (outside) 6620 Cypresswood Drive Suite 120 Spring, TX 77379 832.717.4331
advertisement
Key Features
- AV transmitter & receiver
- Maximum transfer distance: 9 m
- Wireless