Pioneer DEH-X56HD, DEH-X56 X56HD, DEH-X5600HD, DEH-X56 X5600HD Owner's manual

Black plate (1,1)
CD RDS RECEIVER
AUTORADIO CD RDS
REPRODUCTOR DE CD CON RECEPTOR RDS
English
Français
Español
DEH-X5600HD
DEH-X56HD
Owner’s Manual
Mode d’emploi
Manual de instrucciones
Important (Serial number)
The serial number is located on the bottom of this unit. For your own security and
convenience, be sure to record this number on the enclosed warranty card.
Important (Numéro de série)
Le numéro de série se trouve au bas de cet appareil. Pour votre sécurité et votre
commodité, veillez à noter ce numéro sur la carte de garantie fournie.
Importante (Número de serie)
El número de serie se encuentra en la parte inferior de esta unidad. Por su
propia seguridad y comodidad, asegúrese de anotar este número en la tarjeta de
garantía que se adjunta.
<QRD3199-A>1
Black plate (2,1)
Section
Before you start
01
Thank you for purchasing this PIONEER
product
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARNINGs and CAUTIONs in this manual. Please
keep the manual in a safe and accessible place for
future reference.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate
the user’s right to operate the equipment.
Before you start
Note
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/
TV technician for help.
The Safety of Your Ears is in
Your Hands
Get the most out of your equipment by playing it
at a safe level—a level that lets the sound come
through clearly without annoying blaring or distortion and, most importantly, without affecting
your sensitive hearing. Sound can be deceiving.
Over time, your hearing “comfort level” adapts to
higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your
hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing
adapts.
2
ESTABLISH A SAFE LEVEL:
! Set your volume control at a low setting.
! Slowly increase the sound until you can hear
it comfortably and clearly, without distortion.
! Once you have established a comfortable
sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE
FOLLOWING GUIDELINES:
! Do not turn up the volume so high that you
can’t hear what’s around you.
! Use caution or temporarily discontinue use
in potentially hazardous situations.
! Do not use headphones while operating a
motorized vehicle; the use of headphones
may create a traffic hazard and is illegal in
many areas.
! Handling the cord on this product or cords
associated with accessories sold with the
product may expose you to chemicals listed
on proposition 65 known to the State of California and other governmental entities to
cause cancer and birth defect or other reproductive harm. Wash hands after handling.
CAUTION:
USE OF CONTROL OR ADJUSTMENT OR
PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:
THE USE OF OPTICAL INSTRUMENTS
WITH THIS PRODUCT WILL INCREASE
EYE HAZARD.
About this unit
The tuner frequencies on this unit are allocated
for use in North America. Use in other areas
may result in poor reception.
WARNING
! Do not attempt to install or service this
product by yourself. Installation or servicing of this product by persons without
training and experience in electronic
equipment and automotive accessories
may be dangerous and could expose you
to the risk of electric shock, injury or
other hazards.
! Do not attempt to operate the unit while driving. Make sure to pull off the road and park
your vehicle in a safe location before attempting to use the controls on the device.
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and overheating could result from contact with
liquids.
! Always keep the volume low enough to hear
outside sounds.
! Avoid exposure to moisture.
CAUTION
This product is a class 1 laser product classified under the Safety of laser products, IEC
60825-1:2007.
En
<QRD3199-A>2
Black plate (3,1)
Section
Before you start
Using this unit
01
02
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or any
other information. In case the necessary information is not available, please contact the companies listed below:
Please do not ship your unit to the companies at
the addresses listed below for repair without advance contact.
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
340 Ferrier Street
Unit 2
Markham, Ontario L3R 2Z5, Canada
1-877-283-5901
905-479-4411
For warranty information please see the Limited
Warranty sheet included with this unit.
If you experience problems
Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER
Service Station.
Head unit
123 4
78
Remote control
5
9 ab
1
SRC/OFF
2
h (eject)
3
MULTI-CONTROL (M.C.)
4
6
c
5
Disc loading slot
6
USB port
7
MIX (MIXTRAX)
8
BAND/
9
c/d
b
DISP
a
8
m
l
1
k
c
1/
d
AUX input jack (3.5 mm stereo jack)
e
Detach button
j
VOLUME
Press to increase or decrease volume.
g
MUTE
Press to mute. Press again to unmute.
h
a/b
Press to recall preset stations.
Press to select the next/previous folder.
i
AUDIO
Press to select an audio function.
j
DISP/SCRL
Press to select different displays.
Press and hold to turn dimmer on or off.
k
e
Press to pause or resume playback.
l
FUNCTION
Press to select functions.
m
LIST/ENTER
Press to display the list depending on the
source.
While in the operating menu, press to control functions.
to 6/
CAUTION
Use an optional Pioneer USB cable (CD-U50E)
to connect the USB storage device as any device
connected directly to the unit will protrude out
from the unit, which could be dangerous.
g
h
i
f
(iPod control)
(back)/DIMMER (dimmer)
a
f
de
(list)
English
After-sales service for
Pioneer products
En
<QRD3199-A>3
3
Black plate (4,1)
Section
Using this unit
02
Using this unit
3
Display indication
2
1
3
1
2
3
4
5
Main information section
! Tuner: band and frequency
! CD player, USB storage device and iPod:
elapsed playback time and text information
Appears when a lower tier of folder or menu
exists.
Sub information section
5
LOC (local seek tuning)
6
8
9
4 Complete the procedure outlined below
to set the menu.
To proceed to the next menu option, you need to
confirm your selection.
CLOCK SET (setting the clock)
1
2
3
4
Turn M.C. to adjust hour.
Press M.C. to select minute.
Turn M.C. to adjust minute.
Press M.C. to confirm the selection.
QUIT appears.
5 To finish your settings, turn M.C. to select
YES.
(sound retriever)
(random/shuffle)
(repeat)
(iPod control)
This unit’s iPod function is operated from
your iPod.
6
Set up menu
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
Turn M.C. to switch to YES.
# If you do not use the unit for 30 seconds, the set
up menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO.
4
Important
! Handle the front panel with care when removing or attaching it.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle interior, remove any cables and devices attached
to the front panel before detaching it.
Note
When this unit’s blue/white lead is connected to
the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this
unit’s source is turned on. To retract the antenna, turn the source off.
Use and care of the remote
control
3 Always store the detached front panel in a protective case or bag.
Re-attaching the front panel
1 Slide the front panel to the left.
Using the remote control
1 Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1 Slide the tray out on the back of the remote
control.
2 Insert the battery with the plus (+) and minus
(–) poles aligned properly.
Press M.C. to select.
Notes
! You can set up the menu options from the
system menu. For details about the settings,
refer to System menu on page 11.
! You can cancel set up menu by pressing
SRC/OFF.
Basic operations
2
Removing the front panel
1 Press the detach button to release the front
panel.
2 Push the front panel upward (M) and then pull
it toward (N) you.
# If you prefer to change your setting again, turn
M.C. to switch to NO.
(list)
4
7
6 789
Press M.C. to select.
2 Press the right side of the front panel until it is
firmly seated.
Forcing the front panel into place may result in
damage to the front panel or head unit.
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns
off.
Selecting a source
1 Press SRC/OFF to cycle between:
HD RADIO—CD—USB/iPod—PANDORA—
APP (application)—AUX
! USB MTP displays while the MTP connection
is in use.
Adjusting the volume
1 Turn M.C. to adjust the volume.
WARNING
! Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
! Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
! Remove the battery if the remote control is
not used for a month or longer.
En
<QRD3199-A>4
Black plate (5,1)
Section
Using this unit
HD Radio
About HD Radioä stations
HD Radioä stations offer high-quality audio and
data services. HD Radio stations are brought to
you by local FM/AM stations.
HD Radio stations feature the following:
! High quality audio
! FM multicasting
! Data services
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1 Press /DIMMER.
Returning to the ordinary display
Canceling the main menu
1 Press BAND/ .
Returning to the ordinary display from the list
1 Press BAND/ .
HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S.
and Foreign Patents. HD Radioä and the HD,
HD Radio, and “Arc” logos are proprietary trademarks of iBiquity Digital Corp.
Basic operations
Selecting a band
1 Press BAND/ until the desired band (FM1,
FM2, FM3 for FM or AM) is displayed.
Manual tuning (step by step)
1 Press c or d.
! When an analog station is received, tuning
down operation is conducted within the
analog broadcasting. (6 d 2)
! If a digital broadcast is not yet received,
tuning-up operation tunes in the next analog station. (2 d 6)
Important
! Do not store the remote control in high temperatures or direct sunlight.
! The remote control may not function properly
in direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under
the brake or accelerator pedal.
Frequently used menu
operations
HD Radioä Technology
Program Service Data: Contributes to the superior user
experience of HD Radio Technology. Presents song name,
artist, station IDs, HD2/HD3 Channel Guide, and other relevant data streams.
Adjacent to traditional main stations are extra local FM
channels. These HD2/HD3 Channels provide new, original
music as well as deep cuts into traditional genre.
Seeking
1 Press and hold c or d, and then release.
You can cancel seek tuning by briefly pressing
c or d.
While pressing and holding c or d, you can
skip stations. Seek tuning starts as soon as
you release c or d.
02
Storing and recalling stations
for each band
English
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
! Do not handle the battery with metallic tools.
! Do not store the battery with metallic objects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environmental public institutions’ rules that apply in
your country/area.
! “Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/
perchlorate. (Applicable to California,
U.S.A.)”
Using this unit
Using preset tuning buttons
1 To store: Press and hold down one of the
preset tuning buttons (1/ to 6/ ) until
the number stops flashing.
2 To recall: Press one of the preset tuning
buttons (1/ to 6/ ).
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
Analog Radio station
! FREQUENCY (program service name or
frequency)
! TRACK INFO (song title/artist name)
! CLOCK (source name and clock)
HD Radio station
! FREQUENCY (call sign or frequency)
! TRACK INFO (song title/artist name/album
title/genre)
! CLOCK (source name and clock)
Notes
! If the program service name cannot be acquired in FREQUENCY, the broadcast frequency is displayed instead. If the program
service name is detected, the program service name will be displayed.
! If the call sign cannot be acquired in
FREQUENCY, the broadcast frequency is displayed instead. If the call sign is detected,
the call sign will be displayed.
! Depending on the band, text information can
be changed.
! Text information items that can be changed
depend on the area.
Digital, CD-quality sound. HD Radio Technology enables
local radio stations to broadcast a clean digital signal.
AM sounds like today’s FM and FM sounds like a CD.
En
<QRD3199-A>5
5
Black plate (6,1)
Section
Using this unit
02
Function settings
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
BSM (best stations memory)
BSM (best stations memory) automatically stores
the six strongest stations in the order of their signal strength.
1 Press M.C. to turn BSM on.
To cancel, press M.C. again.
LOCAL (local seek tuning)
Local seek tuning allows you to tune in to only
those radio stations with sufficiently strong signals for good reception.
1 Press M.C. to select the desired setting.
FM: OFF—LV1—LV2—LV3—LV4
AM: OFF—LV1—LV2
The highest level setting allows reception of
only the strongest stations, while lower levels
allow the reception of weaker stations.
HD SEEK (seek mode)
Seek tuning setting can be changed between digital station seek (ON) and all station seek (OFF) depending on the reception status.
1 Press M.C. to select your favorite setting.
OFF—ON
Using this unit
BLEND (reception mode)
If a digital broadcast reception condition gets
poor, this unit automatically switches to the analog broadcast of the same frequency level. If this
function is set to on, the tuner switches between
digital broadcast and analog broadcast automatically. If this function is off, reception will be conducted within an analog broadcast.
1 Press M.C. to turn this function on or off.
Note
If HD SEEK is set to ON and BLEND is set to off,
the tuner cannot receive broadcasts. In this
case, the seek mode or reception mode is
changed automatically as follows:
! When HD SEEK is set to ON, if you switch
BLEND from on to off, HD SEEK is changed to
OFF.
! When BLEND is set to off, if you switch HD SEEK
from OFF to ON, BLEND is changed to on.
CD/CD-R/CD-RW and USB
storage devices
MTP connection
MTP-compatible Android devices (running
Android OS 4.0 or higher) can be connected by
MTP connection using the USB source. To connect an Android device, use the cable that came
with the device.
Notes
! This function is not compatible with MIXTRAX.
! This function is not compatible with WAV.
Basic operations
Playing a CD/CD-R/CD-RW
1 Insert the disc into the disc loading slot with
the label side up.
Ejecting a CD/CD-R/CD-RW
1 Press h.
Playing songs on a USB storage device
1 Open the USB port cover.
2 Plug in the USB storage device using a USB
cable.
Stopping playback of files on a USB storage device
1 You may disconnect the USB storage device at
any time.
Selecting a folder
1 Press 1/ or 2/ .
Selecting a track
1 Press c or d.
Fast forwarding or reversing
1 Press and hold c or d.
! When playing compressed audio, there is no
sound during fast forward or reverse.
Returning to root folder
1 Press and hold BAND/ .
Switching between compressed audio and CD-DA
1 Press BAND/ .
Switching between playback memory devices
You can switch between playback memory devices
on USB storage devices with more than one Mass
Storage Device-compatible memory device.
1 Press BAND/ .
! You can switch between up to 32 different
memory devices.
Operations using the MIXTRAX
button
Turning MIXTRAX on or off
You can use this function when USB is selected as
the source.
You cannot use this function with USB MTP.
1 Press MIX to turn MIXTRAX on or off.
! For more details about MIXTRAX, refer to
About MIXTRAX on page 12.
! When MIXTRAX is in use, the sound retriever
function is disabled.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
CD-DA
! ELAPSED TIME (track number and playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
CD-TEXT
! TRACK INFO (track title/track artist/disc
title)
! ELAPSED TIME (track number and playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
MP3/WMA/WAV
! TRACK INFO (track title/artist name/album
title)
! FILE INFO (file name/folder name)
! ELAPSED TIME (track number and playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Note
Disconnect USB storage devices from the unit
when not in use.
6
En
<QRD3199-A>6
Black plate (7,1)
Section
Using this unit
to switch to the file/track name
2 Use M.C. to select the desired file name
(or folder name).
Selecting a file or folder
1 Turn M.C.
Playing
1 When a file or track is selected, press M.C.
Viewing a list of the files (or folders) in the selected folder
1 When a folder is selected, press M.C.
Playing a song in the selected folder
1 When a folder is selected, press and hold M.C.
Operations using special buttons
Selecting a repeat play range
to cycle between the following:
1 Press 6/
CD/CD-R/CD-RW
! ALL – Repeat all tracks
! ONE – Repeat the current track
! FLD – Repeat the current folder
USB storage device
! ALL – Repeat all files
! ONE – Repeat the current file
! FLD – Repeat the current folder
Playing tracks in random order
to turn random play on or off.
1 Press 5/
Tracks in a selected repeat range are played in
random order.
! To change songs during random play, press d
to switch to the next track. Pressing c restarts
playback of the current track from the beginning of the song.
Pausing playback
1 Press 4/PAUSE to pause or resume.
Selecting an album
1 Press 1/ or 2/ .
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
1—2—OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
! Key operation is disabled when MIXTRAX is
on.
Fast forwarding or reversing
1 Press and hold c or d.
Function settings
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
Once selected, the function below can be adjusted.
! S.RTRV is not available when MIXTRAX is
turned on.
S.RTRV (sound retriever)
Automatically enhances compressed audio and
restores rich sound.
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 7.
iPod
Basic operations
Playing songs on an iPod
1 Open the USB port cover.
2 Connect an iPod to USB input.
Playback is performed automatically.
Notes
! The iPod cannot be turned on or off when the
control mode is set to CONTROL AUDIO.
! Disconnect headphones from the iPod before connecting it to this unit.
! The iPod will turn off about two minutes after
the ignition is switched off.
Operations using the MIXTRAX
button
Turning MIXTRAX on or off
1 Press MIX to turn MIXTRAX on or off.
! For more details about MIXTRAX, refer to
About MIXTRAX on page 12.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! TRACK INFO (track title/artist name/album
title)
! ELAPSED TIME (track number and playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
02
2
Use M.C. to select a category/song.
English
Selecting and playing files/
tracks from the name list
Using this unit
Changing the name of the song or category
1 Turn M.C.
Playlists—artists—albums—songs—podcasts
—genres—composers—audiobooks
Playing
1 When a song is selected, press M.C.
Viewing a list of songs in the selected category
1 When a category is selected, press M.C.
Playing a song in the selected category
1 When a category is selected, press and hold
M.C.
Searching the list by alphabet
1 When a list for the selected category is disto switch to alphabet search
played, press
mode.
! You also can switch to alphabet search
mode by turning M.C. twice.
2 Turn M.C. to select a letter.
3 Press M.C. to display the alphabetical list.
! To cancel searching, press /DIMMER.
Notes
! You can play playlists created with the computer application (MusicSphere). The application will be available on our website.
! Playlists that you created with the computer
application (MusicSphere) are displayed in
abbreviated form.
Browsing for a song
1 Press
search.
to switch to the top menu of list
Selecting a song (chapter)
1 Press c or d.
En
<QRD3199-A>7
7
Black plate (8,1)
Section
Using this unit
02
Operations using special buttons
Selecting a repeat play range
1 Press 6/
to cycle between the following:
! ONE – Repeat the current song
! ALL – Repeat all songs in the selected list
! When the control mode is set to CONTROL
iPod, the repeat play range will be same as
what is set for the connected iPod.
Selecting a random play range (shuffle)
to cycle between the following:
1 Press 5/
! SNG – Play back songs in the selected list
in random order.
! ALB – Play back songs from a randomly selected album in order.
! OFF – Not play back in random order.
Playing all songs in random order (shuffle all)
to turn shuffle all on.
1 Press and hold 5/
! To turn off shuffle all, select OFF in shuffle. For
details, refer to Selecting a random play range
(shuffle) on page 8.
Pausing playback
1 Press 4/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
1—2—OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Playing songs related to the
currently playing song
You can play songs from the following lists.
• Album list of the currently playing artist
• Song list of the currently playing album
• Album list of the currently playing genre
1 Press and hold
mode.
to switch to link play
Using this unit
! ARTIST – Plays an album by the artist currently playing.
! ALBUM – Plays a song from the album currently being played.
! GENRE – Plays an album from the genre currently being played.
The selected song/album will be played after the
currently playing song.
Notes
! The selected song/album may be canceled if
you use functions other than link search (e.g.
fast forward and reverse).
! Depending on the song selected to play, the
end of the currently playing song and the beginning of the selected song/album may be
cut off.
Using this unit’s iPod function
from your iPod
This unit’s iPod function can be controlled by
using the connected iPod.
CONTROL iPod is not compatible with the following iPod models.
! iPod nano 1st generation
! iPod with video
% Press BAND/
mode.
to switch the control
! CONTROL iPod – This unit’s iPod function
can be operated from the connected iPod.
! CONTROL AUDIO – This unit’s iPod function
can be controlled by using this unit.
Notes
! Switching the control mode to
CONTROL iPod pauses song playback. Use
the iPod to resume playback.
! The following operations are still accessible
from the unit even if the control mode is set
to CONTROL iPod.
— Pausing
8
— Fast forward/reverse
— Selecting a song (chapter)
2 Turn M.C. to change the mode; press to
select.
! The volume can only be adjusted from this
unit.
Function settings
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
! AUDIO BOOK is not available when
CONTROL iPod is selected in the control
mode. For details, refer to Using this unit’s
iPod function from your iPod on page 8.
AUDIO BOOK (audiobook speed)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select your favorite setting.
! FASTER – Playback at a speed faster than
normal
! NORMAL – Playback at normal speed
! SLOWER – Playback at a speed slower
than normal
S.RTRV (sound retriever)
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 8.
Streaming Pandoraâ
IMPORTANT:
Requirements to access Pandora using the
Pioneer car audio/video products:
! Please update the firmware of the Pandora application to the latest version before use.
! The latest version of the Pandora application can
be downloaded on iTunes App Store.
! Create a free or a paid account online. You can
create the account in the Pandora application
from your iPhone or on the website. The URL in
the following:
http://www.pandora.com/register
! If the Data Plan for your iPhone does not provide
for unlimited data usage, additional charges
from your carrier may apply for accessing the
Pandora service via 3G and/or EDGE networks.
! You need to connect to the Internet via 3G, EDGE
or Wi-Fi network to use the service from Pandora.
Limitations:
! Depending on the availability to the Internet, you
may not be able to receive Pandora service.
! Pandora service is subject to change without notice. The service could be affected by any of the
following: firmware versions of iPhone, firmware
versions of Pandora application, changes to the
Pandora music service.
! Certain functions of the Pandora service are not
available when accessing the service through the
Pioneer car audio/video products. They include,
but not limited to the following: creating new stations, deleting stations, sending information
about current stations, buying tracks from
iTunes, viewing additional text information, logging in to Pandora, adjusting Cell Network Audio
Quality.
Pandora internet radio is a music service not affiliated with Pioneer. More information is available at http://www.pandora.com.
The Pandora mobile application is available for
most iPhone and smartphone, please visit
www.pandora.com/everywhere/mobile for the
latest compatibility information.
Starting procedure for iPhone users
1
Connect an iPhone to USB input.
2
Switch the source to PANDORA.
En
<QRD3199-A>8
Black plate (9,1)
Section
Using this unit
Basic operations
Playing tracks
For details, refer to Starting procedure for iPhone
users on page 8.
Skipping tracks
1 Press d.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! TRACK INFO (station name/track title/artist name/album title)
! ELAPSED TIME (playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Note
Depending on the station, text information can
be changed.
Selecting and playing the
Shuffle/station list
The display shown on this unit may not be the
same as that shown on the connected device.
1 Press
(list) to switch to the Shuffle/station list mode.
2 Use M.C. to select the Shuffle or desired
station.
Changing the sort order
(list).
1 Press
! ABC – You can sort the items in the list alphabetically
! DATE – You can sort the items in the list in
order of the dates on which the items were
created
Changing Shuffle or stations
1 Turn M.C.
Playing
1 When Shuffle or the station is selected, press
M.C.
Deleting stations
1 When station is selected, press and hold M.C.
DELETE YES appears.
To cancel, press /DIMMER. You will return
to the previous level.
2 Press M.C.
The station will be deleted.
Operations using special buttons
Pausing playback
1 Press 4/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
1—2—OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Giving a Thumbs Down
1 Press 2/ to give a “Thumbs Down” for the
track currently playing and to skip to the next
track.
Giving a Thumbs Up
1 Press 1/ to give a “Thumbs Up” for the track
currently playing.
Function settings
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
BOOKMARK (bookmark)
1 Press M.C. to store track information.
NEW STATION (new station)
A new station will be created from the information
for the artist or track of the station currently being
played.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
FROM TRACK (from track)—FROM ARTIST
(from artist)
3 Press M.C.
A new station is created.
! You can also create a new station from a track
.
by pressing and holding down 5/
! You can also create a new station from an artist by pressing and holding down 6/ .
S.RTRV (sound retriever)
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 9.
Using connected device
applications
You can use this unit to perform streaming playback of and control tracks in iPhone applications or just for streaming playback.
02
Important
Use of third party apps may involve or require
the provision of personally identifiable information, whether through the creation of a
user account or otherwise, and for certain applications, the provision of geolocation data.
ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT LIMITATION COLLECTION AND
SECURITY OF USER DATA AND PRIVACY
PRACTICES. BY ACCESSING THIRD PARTY
APPS, YOU AGREE TO REVIEW THE TERMS
OF SERVICE AND PRIVACY POLICIES OF THE
PROVIDERS. IF YOU DO NOT AGREE WITH
THE TERMS OR POLICIES OF ANY PROVIDER
OR DO NOT CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO
NOT USE THAT THIRD PARTY APP.
English
3 Start up the application on the iPhone
and initiate playback.
Using this unit
Information for compatibility of
connected devices
The following is the detailed information regarding the terminals required to use the application
for iPhone on this unit.
For iPhone users
! This function is compatible with iPhone and
iPod touch.
! The device has iOS 5.0 or higher.
Notes
! Please check our website for a list of supported iPhone applications for this unit.
! Pioneer is not liable for any issues that may
arise from incorrect or flawed app-based
content.
! The content and functionality of the supported applications are the responsibility of
the App providers.
En
<QRD3199-A>9
9
Black plate (10,1)
Section
Using this unit
02
Starting procedure for iPhone users
1
Connect an iPhone to USB input.
2
Switch the source to APP.
3 Start up the application on the iPhone
and initiate playback.
Basic operations
Selecting a track
1 Press c or d.
Using this unit
PAUSE (pause)
1 Press M.C. to pause or resume.
S.RTRV (sound retriever)
1 Press M.C. to select the desired setting.
1—2—OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Audio adjustments
Fast forwarding or reversing
1 Press and hold c or d.
1
Pausing playback
1 Press BAND/ to pause or resume.
2 Turn M.C. to change the menu option
and press to select AUDIO.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! TRACK INFO (track title/artist name/album
title)
! APP NAME (application name)
! ELAPSED TIME (playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Function settings
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
Press M.C. to display the main menu.
3 Turn M.C. to select the audio function.
Once selected, the following audio functions
can be adjusted.
! FADER is not available when SUB.W/SUB.W
is selected in SP-P/O MODE. For details, refer
to SP-P/O MODE (rear output and preout setting) on page 12.
! SUB.W and SUB.W CTRL are not available
when REAR/REAR is selected in
SP-P/O MODE. For details, refer to
SP-P/O MODE (rear output and preout setting) on page 12.
! SUB.W CTRL is not available when SUB.W is
selected in OFF. For details, refer to SUB.W
(subwoofer on/off setting) on page 10.
! SLA is not available when FM is selected as
the source.
FADER (fader adjustment)
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the left/right speaker balance.
EQ SETTING (equalizer recall)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the equalizer.
POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS
The equalizer band and equalizer level can be
customized when CUSTOM1 or CUSTOM2 is
selected.
If selecting CUSTOM1 or CUSTOM2, complete
the procedures outlined below. If selecting
other options, press M.C. to return to the previous display.
! CUSTOM1 can be set separately for each
source. However, USB, iPod, PANDORA
and APP are all set to the same setting automatically.
! CUSTOM2 is a shared setting used in common for all sources.
3 Press M.C. to display the setting mode.
4 Press M.C. to cycle between the following:
Equalizer band—Equalizer level
5 Turn M.C. to select the desired setting.
Equalizer band: 80HZ—250HZ—800HZ—
2.5KHZ—8KHZ
Equalizer level: +6 to –6
LOUDNESS (loudness)
Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume.
1 Press M.C. to select the desired setting.
OFF (off)—LOW (low)—MID (mid)—HI (high)
This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to select the desired setting.
NOR (normal phase)—REV (reverse phase)—
OFF (subwoofer off)
SUB.W CTRL (subwoofer adjustment)
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequency—Output level—Slope level
Rates that can be adjusted will flash.
3 Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ—63HZ—80HZ—
100HZ—125HZ—160HZ—200HZ
Output level: –24 to +6
Slope level: –12— –24
BASS BOOST (bass boost)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
HPF SETTING (high pass filter adjustment)
Use this function when wanting to listen only to
high-frequency sounds. Only frequencies higher
than the high-pass filter (HPF) cutoff are output
from the speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequency—Slope level
3 Turn M.C. to select the desired setting.
Cut-off frequency: OFF—50HZ—63HZ—80HZ
—100HZ—125HZ—160HZ—200HZ
Slope level: –12— –24
SUB.W (subwoofer on/off setting)
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the front/rear speaker balance.
BALANCE (balance adjustment)
10
En
<QRD3199-A>10
Black plate (11,1)
Section
Using this unit
The type of text information displayed in the sub
information section can be toggled.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
SPEANA—LEVEL METER—SOURCE—CLOCK
—OFF
! The signal bar indicator displays for SPEANA
or LEVEL METER when the source is set to
HD RADIO.
AUX (auxiliary input)
Activate this setting when using an auxiliary device connected to this unit.
1 Press M.C. to turn AUX on or off.
System menu
DIMMER (dimmer)
1
1 Press M.C. to turn the dimmer on or off.
! You can also change the dimmer setting by
pressing and holding /DIMMER.
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to select the system menu
function.
Once selected, the following system menu functions can be adjusted.
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock
display you wish to set.
Hour—Minute
3 Turn M.C. to adjust the clock.
12H/24H (time notation)
1 Press M.C. to select the desired setting.
12H (12-hour clock)—24H (24-hour clock)
INFO DISPLAY (sub information)
BRIGHTNESS (brightness adjustment)
You can use this setting to adjust the display
brightness.
The range of settings available for BRIGHTNESS
will vary depending on whether DIMMER is on or
off. For details, refer to DIMMER (dimmer) on page
11.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
DIMMER on: 1 to 4
DIMMER off: 1 to 5
Selecting the illumination color
Illumination function menu
1
Press M.C. to display the main menu.
2 Turn M.C. to display ILLUMI and press to
select.
3 Turn M.C. to select the illumination function.
Once selected, the following audio functions
can be adjusted.
KEY COLOR (key section color setting)
You can select desired colors for the keys of this
unit.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the illumination color.
! Preset colors (ranging from WHITE to
BLUE)
! SCAN (cycle through a variety of colors automatically)
! CUSTOM (customized illumination color)
DISP COLOR (display section color setting)
You can select the desired colors for the display of
this unit.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the illumination color.
! Preset colors (ranging from WHITE to
BLUE)
! SCAN (cycle through a variety of colors automatically)
! CUSTOM (customized illumination color)
BOTH COLOR (key and display color setting)
You can select the desired colors for the keys and
display of this unit.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the illumination color.
! Preset colors (ranging from WHITE to
BLUE)
! SCAN (cycle through a variety of colors automatically)
02
ILLUMI FX (illumination effect mode)
English
This function prevents the volume from changing
too dramatically when the source switches.
! Settings are based on the FM volume level,
which remains unchanged.
! The AM volume level can also be adjusted with
this function.
! USB, iPod, PANDORA and APP are all set to
the same setting automatically.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
Using this unit
In this mode, an illumination effect can be seen
on the display at certain times such as when the
ACC power is turned on/off or a CD is inserted/
ejected.
1 Press M.C. to turn ILLUMI FX on or off.
! The illumination effect will activate when the
ACC power is turned on/off regardless of
whether the ILLUMI FX setting is on or off.
Note
When CUSTOM is selected, the customized
color saved is selected.
Customizing the illumination color
You can create custom illumination colors for
both KEY COLOR and DISP COLOR.
1
Press M.C. to display the main menu.
2 Turn M.C. to display ILLUMI and press to
select.
3 Turn M.C. to display KEY COLOR or
DISP COLOR. Press to select.
4 Press M.C. and hold until the customizing
illumination color setting appears in the display.
5 Press M.C. to select the primary color.
R (red)—G (green)—B (blue)
6 Turn M.C. to adjust the brightness level.
Adjustment range: 0 to 60
# You cannot select a level below 20 for all three of
R (red), G (green), and B (blue) at the same time.
# You can also perform the same operation on
other colors.
En
<QRD3199-A>11
11
Black plate (12,1)
Section
Using this unit
02
Note
You cannot create a custom illumination color
while SCAN is selected.
About MIXTRAX
MIXTRAX technology is used to insert a variety
of sound effects in between songs, allowing you
to experience your music as a nonstop mix complete with visual effects.
Notes
! Depending on the file/song, sound effects
may not be available.
! Turn MIXTRAX off if the visual effects it produces have adverse effects on driving. Refer
to Operations using the MIXTRAX button on
page 6.
MIXTRAX menu
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select MIXTRAX.
3 Turn M.C. to select the MIXTRAX function.
Once selected, the following MIXTRAX functions
can be adjusted. The function is enabled when
MIXTRAX is on.
SHORT PLAYBCK (short playback mode)
You can select the length of the playback time.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
1.0 MIN (1.0 minute)—1.5 MIN (1.5 minutes)—
2.0 MIN (2.0 minutes)—2.5 MIN (2.5 minutes)
—3.0 MIN (3.0 minutes)—OFF (off)
FLASH AREA (flash area)
Using this unit
You can select areas for flashing colors.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
KEY/DISPLAY (key and display)—KEY (key)—
OFF (off)
! When OFF is selected, the color set under ILLUMI is used as the display color.
FLASH PATTERN (flash pattern)
The flashing color and MIXTRAX special effects
display change with changes in the sound and
bass levels.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
! SOUND LEVEL 1 to SOUND LEVEL 6 – The
flash pattern changes according to the
sound level. Select a desired mode.
! LOW PASS 1 to LOW PASS 6 – The flash
pattern changes according to the bass
level. Select a desired mode.
! RANDOM 1 – The flash pattern changes
randomly according to the sound level
mode and low pass mode.
! RANDOM 2 – The flash pattern changes
randomly according to the sound level
mode.
! RANDOM 3 – The flash pattern changes
randomly according to the low pass mode.
DISPLAY FX (display effect)
The MIXTRAX special effects display can be turned
on or off.
1 Press M.C. to select the desired setting.
ON (MIXTRAX special effects display)—OFF
(normal display)
CUT IN FX (manual cut-in effect)
You can turn on or off the MIXTRAX sound effects
while manually changing tracks.
1 Press M.C. to select the desired setting.
ON (on)—OFF (off)
Initial menu
1 Press and hold SRC/OFF until the unit
turns off.
2
SP-P/O MODE (rear output and preout setting)
The rear speaker leads output and the RCA output
of this unit can be used to connect a full-range
speaker or subwoofer. Select a suitable option for
your connection.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
! REAR/SUB.W – Select when there is a fullrange speaker connected to the rear speaker leads output and there is a subwoofer
connected to the RCA output.
! SUB.W/SUB.W – Select when there is a
subwoofer connected directly to the rear
speaker leads output without any auxiliary
amp and there is a subwoofer connected
to the RCA output.
! REAR/REAR – Select when there is a fullrange speaker connected to the rear speaker leads output and the RCA output.
If there is a full-range speaker connected to
the rear speaker leads output and the RCA
output is not used, you may select either
REAR/SUB.W or REAR/REAR.
System menu
1 Press and hold SRC/OFF until the unit
turns off.
2
12
Press M.C. to display the main menu.
3 Turn M.C. to change the menu option
and press to select INITIAL.
Once selected, the initial menu function below
can be adjusted.
Press M.C. to display the main menu.
3 Turn M.C. to change the menu option
and press to select SYSTEM.
4 Turn M.C. to select the system menu
function.
For details, refer to System menu on page 11.
Using an AUX source
1 Insert the stereo mini plug into the AUX
input jack.
2 Press SRC/OFF to select AUX as the
source.
Note
AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX
(auxiliary input) on page 11.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! Source name
! Source name and clock
If an unwanted display appears
Turn off the unwanted display using the procedures listed below.
1
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to display DEMO OFF and press
to select.
4
Turn M.C. to switch to YES.
5
Press M.C. to select.
En
<QRD3199-A>12
Black plate (13,1)
Section
Installation
Installation
Ground wire
Other devices
(Another electronic
device in the car)
POWER AMP
Metal parts of car’s body
F
O
N
OF
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
STAR
T
No ACC position
— Disconnect the negative terminal of the battery before installation.
— Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
— Place all cables away from moving parts,
such as the shift lever and seat rails.
— Place all cables away from hot places, such
as near the heater outlet.
— Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
— Use a fuse of the rating prescribed.
— Never wire the negative speaker cable directly
to ground.
— Never band together negative cables of multiple speakers.
! When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
This unit
Perform these connections when using a subwoofer without the optional amplifier.
1
23
1
L
R
2
4
1
2
3
4
5
6
English
WARNING
! Use speakers over 50 W (output value) and
between 4 W to 8 W (impedance value). Do
not use 1 W to 3 W speakers for this unit.
! The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly connected to metal parts of the car’s body. The
ground wire of the power amp and the one of
this unit or any other device must be connected to the car separately with different
screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.
! Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction.
! To prevent a short-circuit, overheating or malfunction, be sure to follow the directions
below.
03
5
6
Power cord input
Rear output or subwoofer output
Front output
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
Power cord
Perform these connections when not connecting a rear speaker lead to a subwoofer.
1
L
R
2
3
4


F

5

R

6
7
8
9
a
b
c
d
e
f
g
h



4

F

i

SW

3
6
7
8
9
a
b
c
d
e
f
g
h
1
2
3
4
5
6
7
8
9
a
b
c
d
e
f
g
h
i




j
a
c
b
d

k
l

To power cord input
Left
Right
Front speaker
Rear speaker
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free metal location.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by ignition
switch (12 V DC).
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).
Subwoofer (4 W)
En
<QRD3199-A>13
13
Black plate (14,1)
Section
Installation
03
Installation
j When using a subwoofer of 70 W (2 W), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
k Not used.
l Subwoofer (4 W) × 2
Notes
! When using a two-speaker system, do not
connect anything to speaker leads that are
not connected to a speaker.
! Change the initial menu of this unit. Refer to
SP-P/O MODE (rear output and preout setting) on page 12.
The subwoofer output of this unit is monaural.
Power amp (sold separately)
Installation
!
!
!
!
Important
Check all connections and systems before
final installation.
Do not use unauthorized parts as this may
cause malfunctions.
Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
Perform these connections when using the optional amplifier.
60°
3
1
Use commercially available parts when installing.
2
Tighten two screws on each side.
1 Insert the mounting sleeve into the dashboard.
For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the vehicle.
2
1
2
3
!
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°) into
place.
1
3
1
DIN Front-mount
Screw
Mounting bracket
Dashboard or console
Use either truss (5 mm × 8 mm) or flush surface (5 mm × 9 mm) screws, depending on
the bracket screw holes.
Removing the unit
1
Remove the trim ring.
2
2
5




3
2
1
7
4
5




6
! When installing, to ensure proper heat dispersal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not blocking the vents.
1 Dashboard
2 Mounting sleeve
# Make sure that the unit is installed securely in
place. An unstable installation may cause skipping
or other malfunctions.
7
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Front output
5 Front speaker
6 To Rear output or subwoofer output
7 Rear speaker or subwoofer
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and the side
of the unit match.
1 Trim ring
2 Notched tab
! Releasing the front panel allows easier access to the trim ring.
! When reattaching the trim ring, point the
side with the notched tab down.
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
5cm
cm
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
14
En
<QRD3199-A>14
Black plate (15,1)
Section
Installation
3
Additional information
Pull the unit out of the dashboard.
Troubleshooting
The display automatically returns to the ordinary
display.
Removing and re-attaching the
front panel
You can remove the front panel to protect your
unit from theft.
For details, refer to Removing the front panel and
Re-attaching the front panel on page 4.
Securing the front panel
The front panel can be secured with the supplied screw.
You did not perform any operation within about 30
seconds.
Perform operation again.
The repeat play range changes unexpectedly.
Depending on the repeat play range, the selected
range may change when another folder or track is
being selected or during fast forwarding/reversing.
Select the repeat play range again.
1 Screw
Common
AMP ERROR
This unit fails to operate or the speaker connection is
incorrect; the protective circuit is activated.
Check the speaker connection. If the message
fails to disappear even after the engine is
switched off/on, contact your dealer or an
authorized Pioneer Service Station for
assistance.
CD player
ERROR-07, 11, 12, 17, 30
A subfolder is not played back.
1
Symptoms are written in bold and causes in regular, non-indented text. Regular, indented text is
used to indicate actions to be taken.
English
Symptoms are written in bold and causes in regular, non-indented text. Regular, indented text is
used to indicate actions to be taken.
03
Subfolders cannot be played when FLD (folder repeat) is selected.
Select another repeat play range.
NO XXXX appears when a display is changed
(NO TITLE, for example).
There is no embedded text information.
Switch the display or play another track/file.
The unit is malfunctioning.
There is interference.
You are using a device, such as a cellular phone,
that may cause audible interference.
Move electrical devices that may be causing the
interference away from the unit.
Error messages
The disc is dirty.
Clean the disc.
The disc is scratched.
Replace the disc.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
There is an electrical or mechanical error.
Turn the ignition switch OFF and back ON, or
switch to a different source, then back to the CD
player.
ERROR-15
The inserted disc is blank.
Replace the disc.
ERROR-23
Unsupported CD format.
Replace the disc.
When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the error
message.
En
<QRD3199-A>15
15
Black plate (16,1)
Appendix
Additional information
Additional information
FORMAT READ
PROTECT
Sometimes there is a delay between the start of playback and when you start to hear any sound.
Wait until the message disappears and you hear
sound.
All the files on the connected USB storage device
are embedded with DRM.
Replace the USB storage device.
iPod failure.
Disconnect the cable from the iPod. Once the
iPod’s main menu is displayed, reconnect the
iPod and reset it.
N/A USB
ERROR-23
The connected USB device is not supported by this
unit.
! Connect a USB Mass Storage Class compliant
device.
! Disconnect your device and replace it with a
compatible USB storage device.
USB storage device was not formatted with FAT12,
FAT16 or FAT32.
USB storage device should be formatted with
FAT12, FAT16 or FAT32.
NO AUDIO
The inserted disc does not contain any playable files.
Replace the disc.
SKIPPED
The inserted disc contains DRM protected files.
The protected files are skipped.
PROTECT
All the files on the inserted disc are embedded with
DRM.
Replace the disc.
USB storage device/iPod
FORMAT READ
Sometimes there is a delay between the start of playback and when you start to hear any sound.
Wait until the message disappears and you hear
sound.
There are no songs.
Transfer the audio files to the USB storage device
and connect.
The connected USB storage device has security enabled.
Follow the USB storage device instructions to
disable the security.
SKIPPED
The connected USB storage device contains DRM
protected files.
The protected files are skipped.
16
The operation was disabled.
Run the same command for another track.
TRY AGAIN
CHECK USB
The iPod firmware version is old.
Update the iPod version.
The USB connector or USB cable has shortcircuited.
Check that the USB connector or USB cable is
not caught in something or damaged.
iPod failure.
Disconnect the cable from the iPod. Once the
iPod’s main menu is displayed, reconnect the
iPod and reset it.
CHECK USB
STOP
The connected USB storage device consumes more
than maximum allowable current.
Disconnect the USB storage device and do not
use it. Turn the ignition switch to OFF, then to
ACC or ON and then connect only compliant
USB storage devices.
There are no songs in the current list.
Select a list that contains songs.
The iPod operates correctly but does not charge.
Make sure the connection cable for the iPod has
not shorted out (e.g., not caught in metal
objects). After checking, turn the ignition switch
OFF and back ON, or disconnect the iPod and
reconnect.
NOT FOUND
No related songs.
Transfer songs to the iPod.
Pandora system is undergoing maintenance.
Try again later.
SKIP LIMIT
Skip limit reached.
! Do not exceed the skip limit.
! Due to music licensing restrictions, Pandora
limits the total number of skips per hour.
CHECK APP
This version of the Pandora application is not supported.
Connect a device that has a compatible version
of the Pandora application installed.
CHECK DEVICE
Pandora
ERROR-19
Communication failed.
Disconnect the cable from the device. Once the
device’s main menu is displayed, reconnect the
device and reset it.
ERROR-19
Communication failed.
Perform one of the following operations.
–Turn the ignition switch OFF and back ON.
–Disconnect the USB storage device.
–Change to a different source.
Then, return to the USB source.
Unable to save thumb rating.
Unable to save BookMark.
Unable to add station.
Try again later.
MAINTENANCE
ERROR-16
CHECK USB
NO AUDIO
INOPERABLE
START UP APP
The Pandora application has not started running yet.
Start up the Pandora application.
Device error message displayed in Pandora application.
Unable to play music from Pandora.
Please check your connected device.
NO STATION
No station found.
Create a station in the Pandora application on
your connected device.
NO ACTIVE ST
No station selected.
Select a station.
En
<QRD3199-A>16
Black plate (17,1)
Appendix
Additional information
Additional information
Handling guidelines
A new station cannot be added.
Delete an old station to open a spot for a new
one.
Discs and player
CAN.T DELETE
Use only discs that feature either of the following
two logos.
NO NETWORK
The connected device is out of area.
Connect the connected device to a network.
NO SERVICE
Use 12-cm discs.
The connected device is out of area.
Connect the connected device to a network.
Use only conventional, fully circular discs.
The operation was disabled.
Run the same command for another station.
Road shocks may interrupt disc playback.
When using discs that can be printed on label surfaces, check the instructions and the warnings of
the discs. Depending on the discs, inserting and
ejecting may not be possible. Using such discs
may result in damage to this equipment.
The station could not be deleted.
Run the same command for another station.
CAN.T PLAY
Playback of discs may not be possible because of
disc characteristics, disc format, recorded application, playback environment, storage conditions,
and so on.
The following types of discs cannot be used with
this unit:
! DualDiscs
! 8-cm discs: Attempts to use such discs with
an adaptor may cause the unit to malfunction.
! Oddly shaped discs
Do not attach commercially available labels or
other materials to the discs.
! The discs may warp making the disc unplayable.
! The labels may come off during playback and
prevent ejection of the discs, which may result
in damage to the equipment.
START UP APP
The application has not started running yet.
Follow the instructions that appear on the
screen.
! Discs other than CDs
! Damaged discs, including discs that are
cracked, chipped or warped
! CD-R/RW discs that have not been finalized
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Do not attach labels, write on or apply chemicals
to the surface of the discs.
To clean a CD, wipe the disc with a soft cloth outward from the center.
Condensation may temporarily impair the player’s
performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any
damp discs off with a soft cloth.
Do not leave the iPod in places with high temperatures.
Firmly secure the iPod when driving. Do not let the
iPod fall onto the floor, where it may become
jammed under the brake or accelerator pedal.
About iPod settings
! When an iPod is connected, this unit changes
the EQ (equalizer) setting of the iPod to off in
order to optimize the acoustics. When you disconnect the iPod, the EQ returns to the original
setting.
! You cannot set Repeat to off on the iPod when
using this unit. Repeat is automatically
changed to All when the iPod is connected to
this unit.
Incompatible text saved on the iPod will not be displayed by the unit.
USB storage device
Connections via USB hub are not supported.
Apps
iPod
English
STATION FULL
Do not connect anything other than a USB storage device.
Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Depending on the USB storage device, the following problems may occur.
! Operations may vary.
! The storage device may not be recognized.
! Files may not be played back properly.
! The device may cause audible interference
when you are listening to the radio.
Compressed audio
compatibility (disc, USB)
WMA
File extension: .wma
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to
384 kbps (VBR)
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream with video: Not compatible
MP3
File extension: .mp3
Bit rate: 8 kbps to 320 kbps (CBR), VBR
En
<QRD3199-A>17
17
Black plate (18,1)
Appendix
Additional information
Sampling frequency: 8 kHz to 48 kHz (32 kHz,
44.1 kHz, 48 kHz for emphasis)
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3 tag Version 2.x is given priority over Version
1.x.)
M3u playlist: Not compatible
MP3i (MP3 interactive), mp3 PRO: Not compatible
WAV
File extension: .wav
Quantization bits: 8 and 16 (LPCM), 4 (MS
ADPCM)
Sampling frequency: 16 kHz to 48 kHz (LPCM),
22.05 kHz and 44.1 kHz (MS ADPCM)
! You cannot use this function with USB MTP.
Supplemental information
Only the first 32 characters can be displayed as a
file name (including the file extension) or a folder
name.
This unit may not work properly depending on the
application used to encode WMA files.
There may be a slight delay at the start of playback
of audio files embedded with image data or audio
files stored on a USB storage device that has numerous folder hierarchies.
Disc
Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)
Playable folders: up to 99
Playable files: up to 999
18
Additional information
File system: ISO 9660 Level 1 and 2, Romeo, Joliet
Multi-session playback: Compatible
Packet write data transfer: Not compatible
Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause
between songs.
USB storage device
Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)
Playable folders: up to 500
Playable files: up to 15 000
Playback of copyright-protected files: Not compatible
Partitioned USB storage device: Only the first partition can be played.
There may be a slight delay when starting playback of audio files on a USB storage device with
numerous folder hierarchies.
CAUTION
! Pioneer cannot guarantee compatibility with
all USB mass storage devices and assumes
no responsibility for any loss of data on
media players, smart phones, or other devices while using this product.
! Do not leave discs or a USB storage device
in any place that is subject to high temperatures.
iPod compatibility
This unit supports only the following iPod models. Supported iPod software versions are shown
below. Older versions may not be supported.
Made for
! iPod touch (5th generation)
! iPod touch (4th generation)
! iPod touch (3rd generation)
! iPod touch (2nd generation)
! iPod touch (1st generation)
! iPod classic
! iPod with video
! iPod nano (7th generation)
! iPod nano (6th generation)
! iPod nano (5th generation)
! iPod nano (4th generation)
! iPod nano (3rd generation)
! iPod nano (2nd generation)
! iPod nano (1st generation)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Depending on the generation or version of the
iPod, some functions may not be available.
Operations may vary depending on the software
version of iPod.
Users of iPod with the Lightning Connector should
use the Lightning to USB Cable (supplied with
iPod).
Users of iPod with the Dock Connector should use
CD-IU51. For details, consult your dealer.
About the file/format compatibility, refer to the
iPod manuals.
Audiobook, Podcast: Compatible
Sequence of audio files
The user cannot assign folder numbers and
specify playback sequences with this unit.
Example of a hierarchy
01
02
03
04
05
Level 1 Level 2 Level 3 Level 4
: Folder
: Compressed
audio file
01 to 05: Folder
number
1 to 6: Playback
sequence
Disc
Folder selection sequence or other operation
may differ depending on the encoding or writing
software.
USB storage device
Playback sequence is the same as recorded sequence in the USB storage device.
To specify the playback sequence, the following
method is recommended.
1 Create a file name that includes numbers
that specify the playback sequence (e.g.,
001xxx.mp3 and 099yyy.mp3).
2 Put those files into a folder.
3 Save the folder containing files on the USB
storage device.
However, depending on the system environment,
you may not be able to specify the playback sequence.
For USB portable audio players, the sequence is
different and depends on the player.
CAUTION
Pioneer accepts no responsibility for data lost
on the iPod, even if that data is lost while this
unit is used.
En
<QRD3199-A>18
Black plate (19,1)
Appendix
Additional information
Copyright and trademark
Apple and iTunes are trademarks of Apple Inc.,
registered in the U.S. and other countries.
MP3
Supply of this product only conveys a license for
private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating)
real time broadcasting (terrestrial, satellite,
cable and/or any other media), broadcasting/
streaming via internet, intranets and/or other
networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for
such use is required. For details, please visit
http://www.mp3licensing.com.
“Made for iPod” and “Made for iPhone” mean
that an electronic accessory has been designed
to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is
not responsible for the operation of this device
or its compliance with safety and regulatory
standards. Please note that the use of this accessory with iPod or iPhone may affect wireless
performance.
Androidä
Android is a trademark of Google Inc.
Pandora® internet radio
PANDORA, the PANDORA logo, and the
Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used
with permission.
WMA
MIXTRAX
Windows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
MIXTRAX is a trademark of the PIONEER
CORPORATION.
iPod & iPhone
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
Lightning is a trademark of Apple Inc.
Specifications
WAV signal format ........... Linear PCM & MS ADPCM
(Non-compressed)
General
Power source ................... 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system ............ Negative type
Maximum current consumption
................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis ............................ 178 mm × 50 mm × 165 mm
(7 in. × 2 in. × 6-1/2 in.)
Nose ................................ 188 mm × 58 mm × 15 mm
(7-3/8 in.× 2-1/4 in.× 5/8 in.)
D
Chassis ............................ 178 mm × 50 mm × 165 mm
(7 in.× 2 in.× 6-1/2 in.)
Nose ................................ 170 mm × 46 mm × 15 mm
(6-3/4 in.× 1-3/4 in.× 5/8 in.)
Weight ............................. 1 kg (2.2 lbs)
Audio
Maximum power output ... 50 W × 4
70 W × 1/2 W (for subwoofer)
Continuous power output
................................... 22 W × 4 (50 Hz to 15 000 Hz,
5 % THD, 4 W load, both channels driven)
Load impedance .............. 4 W (4 W to 8 W allowable)
Preout maximum output level
................................... 2.0 V
Loudness contour ............ +10 dB (100 Hz), +6.5 dB
(10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/
8 kHz
Equalization range ........... ±12 dB (2 dB step)
Subwoofer (mono):
Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Slope ............................... –12 dB/oct, –24 dB/oct
Gain ................................ +6 dB to –24 dB
Phase .............................. Normal/Reverse
CD player
System ............................
Usable discs ....................
Signal-to-noise ratio .........
Number of channels ........
MP3 decoding format ......
WMA decoding format .....
Compact disc audio system
Compact disc
94 dB (1 kHz) (IHF-A network)
2 (stereo)
MPEG-1 & 2 Audio Layer 3
Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
audio)
(Windows Media Player)
USB
USB standard specification
................................... USB 2.0 full speed
Maximum current supply
................................... 1 A
USB Class ....................... MSC (Mass Storage Class)
File system ....................... FAT12, FAT16, FAT32
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
audio)
(Windows Media Player)
WAV signal format ........... Linear PCM & MS ADPCM
(Non-compressed)
English
Additional information
FM tuner
Frequency range .............. 87.9 MHz to 107.9 MHz
Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:
30 dB)
Signal-to-noise ratio ......... 80 dB (digital broadcasting)
(IHF-A network)
Signal-to-noise ratio ......... 72 dB (analog broadcasting)
(IHF-A network)
AM tuner
Frequency range .............. 530 kHz to 1 710 kHz
Usable sensitivity ............. 25 µV (S/N: 20 dB)
Signal-to-noise ratio ......... 80 dB (digital broadcasting)
(IHF-A network)
Signal-to-noise ratio ......... 62 dB (analog broadcasting)
(IHF-A network)
CEA2006 Specifications
Power output ................... 14 W RMS × 4 Channels (4 W
and ≦ 1 % THD+N)
S/N ratio .......................... 91 dBA (reference: 1 W into
4 W)
Note
Specifications and the design are subject to
modifications without notice.
En
<QRD3199-A>19
19
Black plate (20,1)
Section
01
20
APPAREIL À LASER DE CLASSE 1
États-Unis
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Électroniques du Canada, Inc.
DÉPARTEMENT DE SERVICE AUX CONSOMMATEURS
340 Ferrier Street
Unit 2
Markham, Ontario L3R 2Z5, Canada
1-877-283-5901
905-479-4411
Fr
<QRD3199-A>20
Black plate (21,1)
Section
Appareil central
123 4
5
9 ab
1
SRC/OFF
2
3
MULTI-CONTROL (M.C.)
4
c
6
Port USB
7
MIX (MIXTRAX)
a
8
m
l
1
k
de
(liste)
5
f
8
BAND/
9
a
c/d
b
DISP
1/
d
e
à 6/
m
j
Indications affichées
2
1
f
g
h
i
c
g
h
i
l
3
1
j
2
3
5
6 789
4
Section d’informations secondaires
5
6
7
8
k
4
9
02
3
78
6
<QRD3199-A>21
21
Black plate (22,1)
Section
02
!
PRÉCAUTION
22
Fr
<QRD3199-A>22
Black plate (23,1)
Section
02
Fr
<QRD3199-A>23
23
Black plate (24,1)
Section
02
24
Fr
<QRD3199-A>24
Black plate (25,1)
Section
02
Fr
<QRD3199-A>25
25
Black plate (26,1)
Section
02
pour
26
Fr
<QRD3199-A>26
Black plate (27,1)
Section
02
1
2
Basculez la source sur PANDORA.
Fr
<QRD3199-A>27
27
Black plate (28,1)
Section
02
28
2
Basculez la source sur APP.
Fr
<QRD3199-A>28
Black plate (29,1)
Section
S.RTRV (sound retriever)
02
Fr
<QRD3199-A>29
29
Black plate (30,1)
Section
02
30
Fr
<QRD3199-A>30
Black plate (31,1)
Section
02
Fr
<QRD3199-A>31
31
Black plate (32,1)
Section
02
Menu initial
5
32
Fr
<QRD3199-A>32
Black plate (33,1)
Section
Installation
03
L
3
4


F

5

R

6
7
8
9
a
b
c
d
5


L
4

e
f
g
h
R
2
O
STAR
F
N
*1
OF
T
Installation
23
R
2
3
4


F

i

SW

6
7
8
9
a
b
c
d



6
e
f
g
h
1
2
3
4
5
6
7
j
a
c
b
d

k
l

<QRD3199-A>33
33
Black plate (34,1)
Section
Installation
03
8
9
a
b
c
d
e
f
g
h
i
j
k
l
34
Installation
1
2
5




60°
!
!
2
3




6
7
Installation
!
1
4
5
!
2
1
7
5cm
cm
2
3
1
2
Fr
<QRD3199-A>34
Black plate (35,1)
Section
Installation
1
03
Fr
<QRD3199-A>35
35
Black plate (36,1)
ERROR-23
CHECK USB
NO AUDIO
PROTECT
ERROR-19
SKIPPED
N/A USB
36
SKIPPED
INOPERABLE
ERROR-23
TRY AGAIN
Fr
<QRD3199-A>36
Black plate (37,1)
CHECK APP
CAN.T PLAY
CHECK DEVICE
NO SERVICE
NO NETWORK
Fr
<QRD3199-A>37
37
Black plate (38,1)
WAV
Extension de fichier : .wav
WMA
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream avec vidéo : incompatible
MP3i (MP3 interactif), mp3 PRO : incompatible
Extension de fichier : .wma
38
MP3
Fr
<QRD3199-A>38
Black plate (39,1)
02
1
2
MP3
03
3
4
04
Radio Pandora® sur Internet
WMA
MIXTRAX
Fr
<QRD3199-A>39
39
Black plate (40,1)
10,0 A
178 mm × 50 mm × 165 mm
188 mm × 58 mm × 15 mm
178 mm × 50 mm × 165 mm
170 mm × 46 mm × 15 mm
1 kg
40
Fr
<QRD3199-A>40
Black plate (41,1)
<QRD3199-A>41
41
Black plate (42,1)
01
42
PRODUCTO LASER CLASE 1
EE.UU.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADÁ
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
340 Ferrier Street
Unit 2
Markham, Ontario L3R 2Z5, Canadá
1-877-283-5901
905-479-4411
Es
<QRD3199-A>42
Black plate (43,1)
78
SRC/OFF
2
h (expulsar)
3
MULTI-CONTROL (M.C.)
6
c
a
8
m
l
1
k
de
(lista)
5
6
7
MIX (MIXTRAX)
8
BAND/
9
(parte posterior)/DIMMER (reductor de
luz)
a
c/d
b
DISP
c
1/
d
e
m
j
g
1
h
2
i
j
3
3
4
5
6 789
6
2
3
(lista)
5
7
4
8
k
2
1
f
VOLUME
Pulse para aumentar o disminuir el volumen.
a 6/
g
h
i
l
f
02
1
4
Mando a distancia
5
9 ab
6
Es
<QRD3199-A>43
43
Black plate (44,1)
02
!
PRECAUCIÓN
44
Es
<QRD3199-A>44
Black plate (45,1)
02
Es
<QRD3199-A>45
45
Black plate (46,1)
02
46
Es
<QRD3199-A>46
Black plate (47,1)
02
Es
<QRD3199-A>47
47
Black plate (48,1)
02
48
Es
<QRD3199-A>48
Black plate (49,1)
2
02
<QRD3199-A>49
49
Black plate (50,1)
02
50
1
2
PAUSE (pausar)
Avance rápido o retroceso
1 Mantenga pulsado c o d.
Es
<QRD3199-A>50
Black plate (51,1)
02
Es
<QRD3199-A>51
51
Black plate (52,1)
02
52
Menú MIXTRAX
Es
<QRD3199-A>52
Black plate (53,1)
02
5
<QRD3199-A>53
53
Black plate (54,1)
ADVERTENCIA
*1 No se suministra para esta unidad
54
O
STAR
*1
F
N
OF
Conexiones
T
03
L
3
4


F

5

R

6
7
8
9
a
b
c
d
1
2
3
4
5
6
5


L
4

e
f
g
h
R
2
23
R
2
3
4


F

i

SW

6
7
8
9
a
b
c
d



6
e
f
g
h
1
2
3
4
5
6
7
8
j
a
c
b
d

k
l

Es
<QRD3199-A>54
Black plate (55,1)
f
g
i
j
k
l
1
03
2
5




60°
2
3
2
1
7
4
5




6
7
h
5 cm
5 cm
2
3
1
Es
<QRD3199-A>55
55
Black plate (56,1)
03
1
56
No se reproduce una subcarpeta.
Es
<QRD3199-A>56
Black plate (57,1)
Dispositivo de almacenamiento USB o
iPod
NOT FOUND
CHECK USB
<QRD3199-A>57
57
Black plate (58,1)
58
NO ACTIVE ST
STATION FULL
Es
<QRD3199-A>58
Black plate (59,1)
Frecuencia de muestreo: de 8 kHz a 48 kHz
(32 kHz, 44,1 kHz, 48 kHz para énfasis)
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
MP3
Es
<QRD3199-A>59
59
Black plate (60,1)
Copyright y marcas registradas
MP3
02
1
2
03
3
4
04
5
6
05
Nivel 1 Nivel 2 Nivel 3 Nivel 4
60
Es
<QRD3199-A>60
Black plate (61,1)
USB
Es
<QRD3199-A>61
61
Black plate (62,1)
62
Es
<QRD3199-A>62
Black plate (63,1)
<QRD3199-A>63
63
Black plate (64,1)
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,
Kanagawa 212-0031, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
先鋒股份有限公司
台北市內湖區瑞光路407號8樓
電話： 886-(0)2-2657-3588
先鋒電子（香港）有限公司
香港九龍長沙灣道909號5樓
電話： 852-2848-6488
<KOKZ13E>
<QRD3199-A> UC
<QRD3199-A>64">