advertisement
▼
Scroll to page 2
of 24
H:\Data Disk\2348403311\234840331CDXS2050EEEUR\00GB+00COV-EUR.fm masterpage:Right 2-348-403-31 (1) FM/AM Compact Disc Player Operating Instructions GB RU CDX-S2050EE © 2005 Sony Corporation CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB01INT-EUR.fm masterpage:Left Welcome ! Thank you for purchasing this Sony Compact Disc Player. You can enjoy your drive with the following functions. • CD playback: You can play CD-DA and CD-R/CD-RW for audio use. • Radio reception: – You can store up to 6 stations per band (FM1, FM2, FM3, AM1 and AM2). – BTM (Best Tuning Memory) function: the unit selects strong signal stations and stores them. Warning if your car’s ignition has no ACC position After turning the ignition off, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain. This label is located on the bottom of the chassis. 2 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\00GB+00COVEURTOC.fm masterpage:Right Table of Contents Getting Started Other functions Resetting the unit . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 4 DEMO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Detaching the front panel . . . . . . . . . . . . . . . . . 4 Attaching the front panel . . . . . . . . . . . . . . . 4 Changing the sound settings . . . . . . . . . . . . . . . Adjusting the sound characteristics — BAL/FAD/SUB . . . . . . . . . . . . . . . . . . . Adjusting the equalizer curve — EQ3 . . . . Adjusting setup items — SET . . . . . . . . . . . . . Using optional remote commander. . . . . . . . . . Card remote commander RM-X114 . . . . . . Location of controls and basic operations Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Radio Storing and receiving stations . . . . . . . . . . . . . . 6 Storing automatically — BTM . . . . . . . . . . 6 Storing manually . . . . . . . . . . . . . . . . . . . . . 6 Receiving the stored stations . . . . . . . . . . . . 6 Tuning automatically . . . . . . . . . . . . . . . . . . 6 6 6 6 7 7 7 Additional Information Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Notes on discs . . . . . . . . . . . . . . . . . . . . . . . 8 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Removing the unit. . . . . . . . . . . . . . . . . . . . . . . 9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 10 Error displays/Messages . . . . . . . . . . . . . . 11 3 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm Getting Started Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Detach the front panel and press the RESET button with a pointed object, such as a ballpoint pen. RESET button masterpage:Left Detaching the front panel You can detach the front panel of this unit to prevent theft. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. 1 Press (OFF). The unit is turned off. 2 Press , then pull it off towards you. Note Pressing the RESET button will erase the clock setting and some stored contents. (OFF) Setting the clock The clock uses a 24-hour digital indication. 1 Press and hold (SEL). The setup display appears. 2 Press (SEL) repeatedly until “CLOCKADJ” appears. 3 Press (DSPL). The hour indication flashes. 4 Press the volume +/– button to set the hour and minute. To move the digital indication, press (DSPL). 5 Press (SEL). The clock starts and the next setup display appears. 6 Press and hold (SEL). The setup is complete. Notes • Do not drop or put excessive pressure on the front panel and display window. • Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Tip When carrying the front panel, use the supplied front panel case. Attaching the front panel Engage part A of the front panel with part B of the unit, as illustrated, and push the left side into position until it clicks. To display the clock, press (DSPL). Press (DSPL) again to return to the previous display. With the card remote commander In step 4, to set the hour and minute, press M or m. DEMO mode When the unit is turned off, the clock is displayed first, then demonstration (DEMO) mode starts the demonstration display. A B To cancel the DEMO mode, set “DEMO-OFF” in setup (page 7) while unit is turned off. Note Do not put anything on the inner surface of the front panel. 4 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm masterpage:Right Location of controls and basic operations Main unit 1 2 34 5 6 7 8 9 0 SEL SOURCE MODE ATT DIM DSPL SENS 1 2 REP SHUF 3 4 5 6 BTM EQ3 SEEK OFF CDX-S2050EE qa qs qd qf qg qh qj qk Refer to the pages listed for details. a Volume +/– button To adjust volume. b SEL (select) button 4, 6, 7 To select items. c SOURCE button To power on/change the source (Radio/CD). d MODE button 6 To select the radio band (FM/AM). e Disc slot Insert the disc (label side up), playback starts. f Display window g ATT (attenuate) button To attenuate the sound. To cancel, press again. h EQ3 (equalizer) button 6 To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF). i Z (eject) button To eject the disc. j SEEK +/– button Radio: To tune in stations automatically (press); find a station manually (press and hold). CD: To skip tracks (press); fast-forward/reverse a track (press and hold). k (front panel release) button 4 l DSPL (display)/DIM (dimmer) button 4 To change display items (press); change the display brightness (press and hold). m SENS button To improve weak reception: LOCAL/ MONO. n RESET button (located behind the front panel) 4 o Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD: (3): REP To play the current track/disc repeatedly. (4): SHUF To play the tracks in random order. p BTM button 6 To start the BTM function (press and hold). q OFF button To power off/stop the source. r Receptor for the card remote commander 7 5 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm masterpage:Left Radio Other functions Storing and receiving stations Changing the sound settings Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically — BTM 1 2 Press (SOURCE) repeatedly until “TUNER” appears. To change the band, press (MODE) repeatedly. You can select from FM1, FM2, FM3*, AM1 or AM2. Press and hold (BTM) until “BTM” flashes. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored. * FM3 tuning range is 65 to 74 MHz (at 30kHz step). Adjusting the sound characteristics — BAL/FAD/SUB You can adjust the balance, fader and subwoofer volume. 1 LOW*1 t MID*1 t HI*1 t BAL (left-right) t FAD (front-rear) t SUB (subwoofer volume)*2 *1 When EQ3 is activated (page 6). *2 When the audio output is set to “SUB” (page 7). “ATT” is displayed at the lowest setting, and can be adjusted up to 20 steps. 2 Storing manually 1 While receiving the station that you want to store, press and hold a number button ((1) to (6)) until “MEM” appears. The number button indication appears in the display. Note If you try to store another station on the same number button, the previous stored station will be replaced. Receiving the stored stations 1 Select the band, then press a number button ((1) to (6)). With the card remote commander To select preset stations, press M or m. Tuning automatically 1 6 Select the band, then press (SEEK) +/– to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold (SEEK) +/– to locate the approximate frequency, then press (SEEK) +/– repeatedly to fine adjust to the desired frequency (manual tuning). Press (SEL) repeatedly until “BAL,” “FAD” or “SUB” appears. The item changes as follows: Press the volume +/– button repeatedly to adjust the selected item. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Note Adjust within 3 seconds of selecting the item. With the card remote commander In step 2, to adjust the selected item, press <, M, , or m. Adjusting the equalizer curve — EQ3 You can adjust and store the equalizer settings for different tone ranges. 1 Select a source, then press (EQ3) repeatedly to select the EQ3 type. 2 Press (SEL) repeatedly until “LOW,” “MID” or “HI” appears. 3 Press the volume +/– button repeatedly to adjust the selected item. The volume level is adjustable in 1 dB steps, from –10 dB to +10 dB. Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold (SEL) before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm With the card remote commander In step 3, to adjust the selected item, press <, M, , or m. Adjusting setup items — SET masterpage:Right Using optional remote commander Card remote commander RM-X114 1 Press and hold (SEL). The setup display appears. Location of controls 2 Press (SEL) repeatedly until the desired item appears. 3 The corresponding buttons on the card remote commander control the same functions as those on this unit. Press the volume +/– button to select the setting (example “ON” or “OFF”). 4 Press and hold (SEL). The setup is complete and the display returns to normal play/reception mode. Note Displayed items will differ, depending on the source and setting. With the card remote commander In step 3, to select the setting, press < or ,. The following items can be set (follow the page reference for details): “z” indicates the default settings. CLOCK-ADJ (Clock Adjust) (page 4) BEEP To set “BEEP-ON” (z) or “BEEP-OFF.” SUB/REAR*1 To switch the audio output. – “SUB” (z): to output to a subwoofer. – “REAR”: to output to a power amplifier. DIM (Dimmer) To change the brightness of the display. – “DIM-ON”: to dim the display. – “DIM-OFF” (z): to deactivate the dimmer. DEMO*1 To set “DEMO-ON” (z) or (Demonstration) “DEMO-OFF” (page 4). LPF* (Low Pass Filter) 2 To select the cut-off frequency “78HZ,” “125HZ” or “OFF” (z). *1 When the unit is turned off. *2 When the audio output is set to “SUB.” DSPL DSPL MENU* SOURCE </, (SEEK –/+) SEEK– SOUN D DISC + SOURCE DISC – LIST SEEK+ R ENTE + VOL VOL (+/–) m/M (DISC*/ PRESET +/–) ENTER* PRESET – OFF MODE LIST* PRESET + MENU SOUND OFF MODE ATT ATT – The following buttons on the card remote commander have also different buttons/functions from the unit. • SOUND button The same as (SEL) on the unit. • </, (SEEK –/+) buttons To control radio/CD, the same as (SEEK) +/– on the unit. (For details of other operations, see “With the card remote commander” on each pages.) • M/m (DISC*/PRESET +/–) buttons For details, see “With the card remote commander” on each pages. * Not available for this unit. Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. continue to next page t 7 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm Replacing the lithium battery Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the card remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. masterpage:Left Additional Information Precautions • If your car has been parked in direct sunlight, allow the unit to cool off before operating it. • Power aerial will extend automatically while the unit is operating. Moisture condensation On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. x To maintain high sound quality + side up Be careful not to splash juice or other soft drinks onto the unit or discs. Notes on discs Notes on the lithium battery • Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. • Wipe the battery with a dry cloth to assure a good contact. • Be sure to observe the correct polarity when installing the battery. • Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING • To keep a disc clean, do not touch its surface. Handle the disc by its edge. • Keep your discs in their cases or disc magazines when not in use. • Do not subject discs to heat/high temperature. Avoid leaving them in a parked car or on a dashboard/rear tray. • Do not attach labels, or use discs with sticky ink/residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc. Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. • Do not use any discs with labels or stickers attached. The following malfunctions may result from using such discs: – Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism). – Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs. • You cannot play 8 cm CDs. 8 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm • Before playing, clean the discs with a commercially available cleaning cloth. Wipe each disc from the centre out. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue discs. masterpage:Right Removing the unit 1 Remove the protection collar. 1 Detach the front panel (page 4). 2 Engage the release keys together with the protection collar. Notes on CD-R/CD-RW discs • Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/a CD-RW that is not finalized. Orient the release keys as shown. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. 3 Pull out the release keys to remove the protection collar. Maintenance Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. 2 Remove the unit. 1 Insert both release keys simultaneously until they click. Fuse (10A) Hook facing inwards. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 4) and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. 2 Pull the release keys to unseat the unit. 3 Slide the unit out of the mounting. Main unit Back of the front panel Notes • For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. • Never touch the connectors directly with your fingers or with any metal device. 9 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm masterpage:Left Specifications CD Player section Signal-to-noise ratio: 120 dB Frequency response: 10 – 20,000 Hz Wow and flutter: Below measurable limit Tuner section FM Tuning range: FM1/FM2: 87.5 – 108.0 MHz (at 50 kHz step) FM3: 65 – 74 MHz (at 30 kHz step) Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 kHz Usable sensitivity: 9 dBf Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz: 0.5 % (stereo), 0.3 % (mono) Separation: 35 dB at 1 kHz Frequency response: 30 – 15,000 Hz AM Tuning range: 531 – 1,602 kHz Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 kHz Sensitivity: 30 µV Power amplifier section Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 – 8 ohms Maximum power output: 50 W × 4 (at 4 ohms) General Outputs: Audio outputs terminal (sub/rear switchable) Power aerial relay control terminal Power amplifier control terminal Input: Aerial input terminal Tone controls: Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) Power requirements: 12 V DC car battery (negative earth) Dimensions: Approx. 178 × 50 × 178 mm (w/h/d) Mounting dimensions: Approx. 182 × 53 × 161 mm (w/h/d) Mass: Approx. 1.2 kg Supplied accessories: Parts for installation and connections (1 set) Front panel case (1) Optional accessory: Card remote commander: RM-X114 Design and specifications are subject to change without notice. • Lead-free solder is used for soldering certain parts. (more than 80 %) • Halogenated flame retardants are not used in the certain printed wiring boards. • Halogenated flame retardants are not used in cabinets. • Packaging cushions do not use polystyrene foam. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No power is being supplied to the unit. • Check the connection. If everything is in order, check the fuse. • If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit. The power aerial does not extend. The power aerial does not have a relay box. No sound. • The volume is too low. • The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated. • The position of the fader control (FAD) is not set for a 2-speaker system. No beep sound. • The beep sound is cancelled (page 7). • An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. • The RESET button has been pressed. t Store again into the memory. • The power connecting lead or battery has been disconnected. • The power connecting lead is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition key is switched. The leads are not matched correctly with the car’s accessory power connector. 10 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\01GB02CD-EUR.fm masterpage:Right The display disappears from/does not appear in the display window. During FM reception, the “ST” indication flashes. • The dimmer is set “DIM-ON” (page 7). • The display disappears if you press and hold (OFF). t Press and hold (OFF) again until the display appears. • The connectors are dirty (page 9). • Tune in the frequency accurately. • The broadcast signal is too weak. t Press (SENS) to set the monaural reception mode to “MONO-ON.” CD playback An FM programme broadcast in stereo is heard in monaural. The unit is in monaural reception mode. t Press (SENS) until “MONO-OFF” appears. The disc cannot be loaded. • Another disc is already loaded. • The disc has been forcibly inserted upside down or in the wrong way. The disc does not playback. • Defective or dirty disc. • The CD-Rs/CD-RWs are not for audio use (page 9). The sound skips. • Installation is not correct. t Install the unit at an angle of less than 45° in a sturdy part of the car. • Defective or dirty disc. The operation buttons do not function. The disc will not eject. Press the RESET button (page 4). Radio reception The stations cannot be received. The sound is hampered by noises. • Connect a power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a car’s aerial booster (only when your car has built-in FM/AM aerial in the rear/ side glass). • Check the connection of the car aerial. • The auto aerial will not go up. t Check the connection of the power aerial control lead. • Check the frequency. Preset tuning is not possible. • Store the correct frequency in the memory. • The broadcast signal is too weak. Automatic tuning is not possible. Error displays/Messages ERROR • The disc is dirty or inserted upside down. t Clean or insert the disc correctly. • The disc cannot play because of some problem. t Insert another disc. FAILURE The speaker/amplifier connection is incorrect. t See the supplied installation/connections manual to check the connection. L.SEEK +/– The local seek mode is on during automatic tuning. OFFSET There may be an internal malfunction. t Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. RESET The unit cannot be operated because of some problem. t Press the RESET button (page 4). “ ” or “ ” During fast-forward or reverse, you have reached the beginning or the end of the disc and you cannot go any further. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. • Setting of the local seek mode is not correct. t Tuning stops too frequently: Press (SENS) until “LOCAL-ON” appears. t Tuning does not stop at a station: Press (SENS) repeatedly until “MONOON” or “MONO-OFF” (FM), or “LOCALOFF” (AM) appears. • The broadcast signal is too weak. t Perform manual tuning. 11 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU01INT-EUR.fm masterpage:Left 2 CDX-S2050EE 2-348-403-31(1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU+00COVEURTOC.fm masterpage:Right Другие функции 8 8 8 8 9 9 10 10 11 12 12 13 14 3 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Left 1 1 2 2 Нажимайте кнопку (SEL), пока не появится индикация “CLOCK-ADJ”. 3 4 5 6 Нажмите и удерживайте кнопку (SEL). Установка завершена. (OFF) 4 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Right A B 5 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Left 1 2 34 5 6 7 8 9 0 SEL SOURCE MODE ATT DIM DSPL SENS 1 2 REP SHUF 3 4 5 6 BTM EQ3 SEEK OFF CDX-S2050EE qa qs qd qf qg qh qj qk 6 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm Радиоприемник 2 masterpage:Right * Диапазон настройки FM3 - от 65 до 74 МГц (шаг 30 кГц). 7 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm Другие функции 2 Нажимайте кнопку (SEL), пока не появится индикация “LOW”, “MID” или “HI”. 3 1 2 1 8 masterpage:Left 2 3 4 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm (стр. 4) BEEP SUB/REAR* 1 masterpage:Right DSPL MENU* SOURCE </, (SEEK –/+) SEEK– SOUN VOL (+/–) D DISC + SOURCE DISC – LIST SEEK+ R ENTE + m/M (DISC*/ PRESET +/–) ENTER* PRESET – OFF MODE LIST* PRESET + MENU SOUND OFF MODE ATT VOL ATT – 9 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Left 10 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Right 11 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Left Снимите защитную манжету. Тюнер FM Установите ключи для демонтажа, как показано на рисунке. AM 2 Общие 12 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm masterpage:Right Нет звука. 13 CDX-S2050EE 2-348-403-31 (1) H:\Data Disk\2348403311\234840331CDXS2050EEEUR\02RU02CD-EUR.fm L.SEEK +/– OFFSET masterpage:Left ” или “ ” Sony Corporation Printed in China CDX-S2050EE 2-348-403-31 (1)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project