Milwaukee 0721-20 User guide

Milwaukee 0721-20 User guide
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
Cat. No.
No de cat.
0721-20
28 VOLT 1/2" RIGHT ANGLE DRILL
13 mm (1/2") POIGNÉE COUDEE ANGLE DROIT 28 V
TALADROS EN ANGULOS RECTOS, DE 13 mm (1/2") CON
EMPUNADURA EN "D" DE 28 V
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
READ ALL SAFETY WARNINGS AND INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury. Save all warnings and instructions for future reference
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
attached to a rotating part of the power tool may
result in personal injury.
•Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
•If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WORK AREA SAFETY
•Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
•Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
•If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
•Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
•Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
•Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
PERSONAL SAFETY
2
•Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
•Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
•Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
BATTERY TOOL USE AND CARE
•Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
•Use power tools only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
3
•When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
•Keep hands away from all cutting edges and
moving parts.
•Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•lead from lead-based paint
•crystalline silica from bricks and cement and other
masonry products, and
•arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SERVICE
•Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
•Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.
•Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
•Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a live wire will make exposed metal
parts of the tool live and shock the operator.
Volts No load
DC
RPM
28 Hi 0 - 1000
Lo 0 - 400
Flat Boring Bits
1-1/2"
1-1/2"
ger specified for the battery. For specific charging instructions, read the operator’s
manual supplied with your charger and battery.
lowing instructions (see “Removing
the Chuck from the Drill”). Slip the
double hex coupling (1) over the hex
on the drill spindle.
3
Loosen the clamping screws on
the clamping sleeve (2) and slip the
sleeve onto the drill collar.
2
2. Slide the right angle drill head (3)
into the other side of the sleeve
and turn the drive head slightly in
either direction so the hexagonal
1
hole in the coupling engages the
hexagonal portion of the spindle.
NOTE: Attaching the drill chuck to the side designated “low” reduces the speed by 1/3, or 33%.
Attaching the drill chuck to the opposite side of
the right angle drill head increases the speed by
1/2, or 50%.
3. When assembled, turn the right angle head to the
desired position and tighten the clamping screws
to secure the unit. Thread the chuck onto the right
angle drive spindle and install the chuck screw.
WARNING
Always remove battery
pack before changing or removing
accessories. Only use accessories specifically recommended for this tool. Others may
be hazardous.
Removing Battery Pack from Tool
Push in the release buttons and pull the battery
pack away from the tool.
Inserting Battery Pack into Tool
To insert the battery pack onto the tool, slide the
pack onto the body of the tool. Make sure it latches
securely into place.
WARNING To reduce the risk of injury,
always use a side handle when using
this tool. This tool operates with high torque.
Always brace or hold the tool securely.
WARNING
SPECIFICATIONS
Cat. No.
0721-20
ASSEMBLY
Right Angle Drive to a Drill
WARNING Recharge only with the char- Attaching
1. Remove the chuck from the drill fol-
Capacities in Wood
Hole Saw
Auger Bit Ship Auger Bit Selfeed Bit
3-1/2"
3/4"
1"
1"
4-1/2"
1-1/2"
1-1/2"
2-9/16"
Use only MILWAUKEE M28™ or V28® battery packs.
FUNCTIONAL DESCRIPTION
SYMBOLOGY
2
4
Direct Current
3
5
1
Underwriters Laboratories, Inc.
United States and Canada
No Load Revolutions per
Minute (RPM)
7
6
1. Handle
2. Forward/Reverse/Trigger
lock switch
3. Trigger
4
4. Right angle
drive unit
5. Side handle
6. Chuck
7. Ring clamp
Removing the Chuck from the RAD
The chuck can be removed
from the right angle drive
unit in the same manner
it is removed from the
drill; however, ALWAYS
REMOVE RIGHT ANGLE
DRIVE FROM THE DRILL
BEFORE ATTEMPTING
TO LOOSEN THE CHUCK.
This will prevent damaging
the drill's gearing. Use the open end wrench provided to hold the right angle drive spindle before
attempting to loosen the chuck.
When using the D-handle
drill without the right angle drive
unit, do not clamp the ring clamp with attached side handle to the front of the gear
case; use the side handle instead.
Do not use the extension when using the
ring clamp.
Ring Clamp, Extension, and Side Handle for
Right Angle Drive (RAD)
For D-handle drill with RAD:
A ring clamp, extension, and side handle are supplied with the Right Angle Drive Unit. When using a
right angle drive unit, attach the side handle to the
ring clamp. Do not use the extension when using
the ring clamp. The ring clamp with attached side
handle clamps onto the right angle drive unit and
can swivel 360° and locked tight in any position.
For D-handle drill without RAD:
When using the D-handle drill without the right
angle drive unit, remove the ring clamp with attached side handle from the RAD, then remove
the side handle from the ring clamp. Attach the
side handle to the extension. The side handle can
be installed on either side of the tool for right or left
handed use. To install the extension with attached
side handle, thread it into the socket on the desired
side of the tool (for right or left-handed use) and
tighten securely.
NOTE: If you have an extra ring clamp with attached side handle and extension with attached
side handle, do not use the extension with attached
side handle when using the right angle drive unit.
Remove it from the tool.
Removing the Chuck from the Drill
1. To remove the left-hand
screw inside the chuck,
remove the battery pack
from the tool and open
the chuck jaws. Insert a
T-handle hex key into the
screw inside the chuck.
Turn the T-handle hex key
and remove the screw.
Save the screw for installing your new chuck.
2. To remove chuck: Tighten
a large hex key into the chuck. Place the chuck
on a workbench as shown. Strike the hex key
with a soft-headed mallet to loosen the chuck.
Remove the chuck by hand.
5
OPERATION
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handle firmly and pull
the trigger.
2. To vary the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
3. To stop the tool, release the trigger. Make sure
the tool comes to a complete stop before laying
the tool down.
WARNING
Always remove battery
pack before changing or removing
accessories. Only use accessories specifically recommended for this tool. Others may
be hazardous.
WARNING To reduce the risk of injury,
keep hands away from the bit and all
moving parts. Always wear safety goggles or
glasses with side shields. Always remove the
chuck key from the chuck after each use.
Electric Brake
The electric brake engages when the trigger is
released, causing the bit to stop and allowing you
to proceed with your work. Generally, the bit stops
within two seconds. However, there may be a delay
between the time you release the trigger and when
the brake engages. Occasionally the brake may
miss completely. If the brake misses frequently, the
tool needs servicing by an authorized MILWAUKEE
service facility.
Installing Bits into Keyed Chuck
1. Open the chuck jaws
wide enough to insert
the bit. Be sure the
bit shank and chuck
jaws are clean. Dirt
particles may prevent
the bit from lining up Tighten
properly.
2. When using drill bits,
Loosen
insert the bit into the
chuck. Center the bit in
the chuck jaws and lift it about 1/16" off of the
bottom. Tighten the chuck jaws by hand to align
the bit.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the bit shank.
Tighten the chuck jaws by hand to align the bit.
3. Place the chuck key in each of the three holes in
the chuck, turning it clockwise as shown. Tighten
securely.
4. To remove the bit, insert the chuck key into one
of the holes in the chuck and turn it counterclockwise.
APPLICATIONS
WARNING To reduce the risk of
personal injury, hold the tool securely. Brace tools with side handles as shown.
If the bit binds, the tool will be forced in the
opposite direction. Bits may bind if they are
misaligned or when breaking through a hole.
Wood boring bits can also bind if they run into
nails or knots.
Selecting Bits
When selecting a bit, use the right type for your job.
For best performance, always use sharp bits.
Drilling
1. Before drilling, be sure the workpiece is clamped
securely. Use backing material to prevent damage to the workpiece during breakthrough.
2. When starting a hole, place the drill bit on the
work surface and apply firm pressure. Begin
drilling at a slow speed, gradually increasing the
speed as you drill.
3. Always apply pressure in line with the bit. Use
enough pressure to keep the drill biting, but do
not push hard enough to stall the motor.
4. Reduce pressure and ease the bit through the
last part of the hole. While the tool is still running,
pull the bit out of the hole to prevent jamming.
Bracing against
a stud
Reverse
rotation
Reaction
Reaction
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, start the drill slowly, gradually increasing
speed as you drill. When drilling into wood, use
wood augers or twist drill bits. Always use sharp
bits. When using twist drill bits, pull the bit out of the
hole frequently to clear chips from the bit flutes. To
reduce the chance of splintering, back work with a
piece of scrap wood. Select low speeds for plastics
with a low melting point.
Bracing against
a stud
Forward
rotation
Forward/Reverse/Trigger Lock Switch
To set the direction of bit rotation or lock the
trigger, move the forward/reverse/trigger
lock switch to the following positions:
For forward rotation (clockwise): Move the
switch to the right." " will be displayed
above the switch. To vary the speed in
forward rotation, increase or decrease
pressure on the trigger.
Bracing
against
your leg
For reverse rotation (counter-clockwise):
Move the switch to the left. " " will be displayed above the switch. To vary the speed
in reverse rotation, increase or decrease
pressure on the trigger.
Reaction
Forward
rotation
Forward
rotation
To lock the trigger: Move the switch to the
center. "
" will be displayed above the
switch. The trigger will not work while the
switch is in the locked position. Always
lock the trigger and remove the battery
pack before performing maintenance and
changing accessories. Lock the trigger
when storing the tool and when the tool
is not in use.
Bracing
against the
floor
Reaction
6
7
MAINTENANCE
LIMITED WARRANTY - USA AND CANADA
ACCESSORIES
WARNING To reduce the risk of injury,
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble the tool, battery pack or charger.
Contact a MILWAUKEE service facility for
ALL repairs.
WARNING Always remove battery
pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go online
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or service center.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to A
MILWAUKEE service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and
electrical operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
WARNING To reduce the risk of personal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to flow inside them.
Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORDLESS
BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defective in
material or workmanship for a period of five (5) years* after the date of purchase unless otherwise noted. Return of the
power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid
and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty
does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than
MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
*The warranty period for, Job Site Radios, M12™ Power Port and Trade Titan™ Industrial Work Carts is one (1) year from
the date of purchase. The warranty period for a LED Work Light and LED Upgrade Bulb is a limited LIFETIME warranty
to the original purchaser only, if during normal use the LED bulb fails the Work Light or Upgrade Bulb will be replaced
free of charge.
*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline Driven
Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned
product and Test & Measurement products. There are separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product. The
manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at
the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF
THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION,
YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES
OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES
ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.com
or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE factory Service Center location.
LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN
Cleaning
Clean dust and debris from charger and tool
vents. Keep tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased
the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the original
proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to find the nearest ASC, for service, parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all
freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.
Repairs
For repairs, return the tool, battery pack and charger to the nearest service center.
Model:
Date of Purchase:
Distributor or Store Stamp:
8
SERVICE AND ATTENTION CENTER
Rafael Buelna No.1.
Col. Tezozomoc Mexico, Azcapotzalco D.F.
Ph. 01 800 832 1949
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av. Santa Fe 481 piso 6, Col. Curz Manca.
CP 05349, Cuajimalpa, D.F.
9
PICTOGRAPHIE
Tours-minute á vide (RPM)
Underwriters Laboratories, Inc.
États-Unis et Canada
11
DESCRIPTION FONCTIONNELLE
2
4
3
5
1
12
13
APPLICATIONS
rotation
avant
rotation
adelante
rotation
avant
rotation avant
ACCESOIRES
AVERTISSEMENT
14
15
IMPORTÉ ET COMMERCIALISÉ PAR :
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av. Santa Fe 481 piso 6, Col. Curz Manca.
CP 05349, Cuajimalpa, D.F.
16
DESCRIPCION FUNCIONAL
2
4
MANTENIMIENTO
3
5
1
REGLAS ESPECIFICAS
DE SEGURIDAD
ESPECIFICACIONES
Capacidades
Volts
Brocas de
Brocas
Brocas de
Brocas de
Brocas de
Cat. No. cd
rpm
Manita
Sierras
Husillo
Husillo Larga Autoalimenta-doras
0721-20 28 alta 0-1 000 38 mm (1-1/2") 89 mm (3-1/2") 19 mm (3/4")
25 mm (1")
25 mm (1")
baja 0-400 38 mm (1-1/2") 114 mm (4-1/2") 38 mm (1-1/2") 38 mm (1-1/2") 65 mm (2-9/16")
Utilice solamente las baterías de MILWAUKEE M28™ o V28®.
19
20
21
APPLICACIONES
MANTENIMIENTO
22
23
UNITED STATES
MILWAUKEE Service
MILWAUKEE prides itself in producing a premium
quality product that is NOTHING BUT HEAVY DUTY®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, or you would like to locate the
factory Service/Sales Support Branch or authorized
service station nearest you, please call...
Additionally, we have a nationwide network of
authorized Distributors ready to assist you with
your tool and accessory needs. Check your “Yellow
Pages” phone directory under “Tools-Electric” for
the names & addresses of those nearest you or see
the 'Where To Buy' section of our website.
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday
7:00 AM - 6:30 PM
Central Time
or visit our website at
www.milwaukeetool.com
For service information, use the 'Service Center
Search' icon found in the 'Parts & Service' section.
Contact our Corporate After Sales Service
Technical Support about ...
•Technical Questions
•Service/Repair Questions
•Warranty
call: 1-800-SAWDUST
fax: 1.800.638.9582
email: [email protected]
Register your tool online at
www.milwaukeetool.com and...
• receive important notifications regarding
your purchase
• ensure that your tool is protected under the
warranty
• become a HEAVY DUTY club member
CANADA - Service MILWAUKEE
MILWAUKEE prides itself in producing a premium
quality product that is NOTHING BUT HEAVY DUTY®.
Your satisfaction with our products is very important to us!
If you encounter any problems with the operation
of this tool, or you would like to locate the factory
Service/Sales Support Branch or authorized service station nearest you, please call...
1.800.268.4015
Monday – Friday 7:00 – 4:30 CST
fax: 866.285.9049
Milwaukee Electric Tool (Canada) Ltd
140 Fernstaff Court, Unit 4
Vaughan, ON L4K 3L8
18129 111 Avenue NW
Edmonton, AB T5S 2P2
Additionally, we have a nationwide network of
authorized Distributors ready to assist you with your
tool and accessory needs. Call 1.800.268.4015 to
find the names and addresses of the closest retailers or consult “Where to buy” on our Web site
www.milwaukeetool.com
1.800.268.4015
Lundi – Vendredi 7:00 – 4:30 CST
fax: 866.285.9049
Milwaukee Electric Tool (Canada) Ltd
140 Fernstaff Court, Unit 4
Vaughan, ON L4K 3L8
18129 111 Avenue NW
Edmonton, AB T5S 2P2
www.ttigroupmexico.com
MILWAUKEE ELECTRIC TOOL CORPORATION
58-14-0721d6
13135 West Lisbon Road • Brookfield, Wisconsin, U.S.A. 53005
07/11
Printed in China
960931519-02( )
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed