advertisement
▼
Scroll to page 2
of 80
Refrigerator user manual English imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www.samsung.com/register Free Standing Appliance DA68-02616B Rev. 01 safety information SAFETY INFORMATION • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Use this appliance only for its intended purpose as described in this instruction manual. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your appliance. • Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual. R600a or R134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the fridge to see which refrigerant is used for your refrigerator. When this product contains flammable gas (Refrigerant R600a), contact your local authority in regard to safe disposal of this product. Important safety symbols and precautions: WARNING Hazards or unsafe practices that may result in severe personal injury or death. CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. Do NOT attempt. Do NOT disassemble. Do NOT touch. Follow directions carefully. Unplug the power plug from the wall socket. 02_ Safety information Make sure the refrigerator is grounded to prevent electric shock. Call the contact center for help. Note. These warning signs are here to prevent injury to you and others. Please follow them carefully. After reading this section, keep it in a safe place for future reference. CE Notice This product has been determined to be in compliance with the Low Voltage Directive (2006/95/EC), the Electromagnetic Compatibility Directive (2004/108/EC), Commission Delegated Regulation (EU) No 1060/2010 and the Eco-Design Directive(2009/125/EC) implemented by Regulation (EC) No 643/2009 of the European Union. (For products sold in European Countries only) WARNING SEVERE WARNING SIGNS FOR TRANSPORTATION AND SITE • When transporting and installing the appliance,care should be taken to ensure that no parts of the refrigerating circuit are damaged. • R600a or R134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the refrigerator to see which refrigerant is used for your refrigerator. • When this product contains flammable gas (Refrigerant R600a), - Refrigerant leaking from the pipe work could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. - In order to avoid the creation of a flammable gas-air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. - - Never start up an appliance showing any signs of damage. If in doubt, consult your dealer. The room where the refrigerator will be sited must be 1 m³ in size for every 8 g of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification plate inside the appliance. If the appliance contains isobutane refrigerant (R600a), a natural gas with high environmental compatibility that is, however, also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. WARNING • • - • • • • • • SEVERE WARNING SIGNS FOR INSTALLATION • Do not install the refrigerator in a damp place or place where it may come in contact with water. Deteriorated insulation of electrical parts may cause an electric shock or fire. Do not place this refrigerator in direct sunlight or expose to the heat from stoves, room heaters or other appliances. Do not plug several appliances into the same multiple power board. The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matched the rating plate. This provides the best performance and also prevents overloading house wiring circuits, which could cause a fire hazard from overheated wires. If the wall socket is loose, do not insert the power plug. There is a risk of electric shock or fire. Do not use a cord that shows cracks or abrasion damage along its length or at either end. Do not bend the power cord excessively or place heavy articles on it. Do not use aerosols near the refrigerator. Aerosols used near the refrigerator may cause an explosion or fire. Do not install this appliance in a location where gas may leak. This may result in an electric shock or fire. Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord or loose wall socket. This may result in an electric shock or fire. This appliance must be properly grounded. - - • • • • • • Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line. You must ground the refrigerator to prevent any power leakages or electric shocks caused by current leakage from the refrigerator. This may result in an electric shock, fire, explosion, or problems with the product. Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes. Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance. When moving the refrigerator, be careful not to roll over or damage the power cord. This may result in an electric shock or fire. This appliance should be positioned in such a way that it is accessible to the power plug. Failing to do so may result in an electric shock or fire due to electric leakage. Do not install this appliance near a heater, inflammable material. Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct sunlight and water (rain drops). • The installation or any service of this appliance is recommended by a qualified technician or service company. - Failing to do so may result in an electric shock, fire, explosion, problems with the product, or injury. • Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance. - This may result in an electric shock, fire, problems with the product, or injury. - The installation or any service of this appliance is recommended by a qualified technician or service company. - Failing to do so may result in an electric shock, fire, explosion, problems with the product, or injury. - Do not touch the power plug with wet hands. - This may result in an electric shock. • This refrigerator must be properly installed and located in accordance with the manual before it is used. Safety information _03 • Connect the power plug in proper position with the cord hanging down. - If you connect the power plug upside down, wire can get cut off and a cause fire or an electric shock. • Make sure that the power plug is not squashed or damaged by the back of the refrigerator. • When moving the refrigerator, be careful not to roll over or damage the power cord. - This constitutes a fire hazard. • The appliance must be positioned so that the plug is accessible after installation. • The refrigerator must be grounded. - You must ground the refrigerator to prevent any power leakages or electric shocks caused by current leakage from the refrigerator. • Never use gas pipes, telephone lines or other potential lightening rods as ground. - Improper use of the ground plug can result in an electric shock. • If the power cord is damaged, have it replaced immediately by the manufacturer or its service agent. • The fuse on the refrigerator must be changed by a qualified technician or service company. - Failing to do so may result in an electric shock or personal injury. CAUTION CAUTION SIGNS FOR INSTALLATION • Keep ventilation opening in the appliance enclosure or mounting structure clear of obstruction. • Allow the appliance to stand for 2 hours after installation. WARNING SEVERE WARNING SIGNS FOR USING • Do not insert the power plug with wet hands. • Do not store articles on the top of the appliance. - When you open or close the door, the articles may fall and cause a personal injury and/or material damage. • Do not put items filled with water on the refrigerator. 04_ Safety information - If spilled, there is a risk of fire or electric shock. • Do not let children hang on the door. - Failure to do so may cause serious personal injury. • Do not leave the doors of the refrigerator open while the refrigerator is unattended and do not let children enter inside the refrigerator. • Do not allow babies or children go inside the drawer. - It can cause death from suffocation by entrapment or personal injury. • Do not sit on the Freezer door. - The door may be broken and cause a personal injury. • Do not put a container filled with water on the refrigerator. - If spilled, there is a risk of fire or electric shock. - Do not use or place any substances sensitive to temperature such as inflammable sprays, inflammable objects, dry ice, medicine, or chemicals near or inside of the refrigerator. - Do not keep volatile or inflammable objects or substances (benzene, thinner, propane gas, alcohol, ether, LP gas and other such products etc.) in the refrigerator. - This refrigerator is for storing food only. - This may result in fire or explosion. • Do not store pharmaceuticals products, scientifi c materials or temperature-sensitive products in the refrigerator. - Products that require strict temperature controls must not be stored in the refrigerator. • If you smell pharmaceutical or smoke, pull out power plug immediately and contact your Samsung Electronics service center. • If any dust or water is in Refrigerator, pull out power plug and contact your Samsung Electronics service center. - Otherwise there is a risk of fire. • If gas leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. • Do not attempt to repair, disassemble, or modify the appliance yourself. - Do not use any fuse (such as cooper, steel wire, etc.) other than the standard fuse. - When repairing or reinstalling the appliance is required, contact your nearest service center. - Failing to do so may result in an electric shock, fire, problems with the product, or injury. • To prevent children entrapment, you must • • • • • • • • • • • • • reinstall the divider using provided screws after cleaning or other actions if you removed the divider from the drawer. Never put fingers or other objects into the dispenser hole. Failure to do so may cause personal injury or material damage. Do not store volatile or flammable substances such as benzene, thinner, alcohol, ether or LP gas in the refrigerator. The storage of any of such products may cause an explosion. Do not store low temperature-sensitive pharmaceutical products, scientific materials or other low temperature-sensitive products in the refrigerator. Products that require strict temperature controls must not be stored in the refrigerator. Do not place or use electrical appliance inside the refrigerator, unless they are of a type recommended by the manufacturer. Do not use a hair dryer to dry the inside of the refrigerator. Do not place a lighted candle in the refrigerator for removing bad odors. This may result in an electric shock or fire. Do not touch the inside walls of the freezer or products stored in the freezer with wet hands. This may cause frostbite. Do not use mechanical devices or any other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not damage the refrigerant circuit. • This product is intended only for the storage of food in a domestic environment. Bottles should be stored tightly together so that they do not fall out. In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without touching the power plug. Do not touch the appliance or power cord. Do not use a ventilating fan. A spark may result in an explosion or fire. Use only the LED Lamps provided by manufacturer or service agent. If the products is equipped with the LED Lamp, do not disassemble Lamp Cover and LED Lamp by yourself. Please contact your service agent. Use only the LED Lamps provided by manufacturer or service agent. • Never stare directly at the UV LED lamp for long periods of time. - This may result in eye strain due to the ultraviolet rays. • Children should be supervised to ensure that they do not play with and/or climb into the appliance. - Keep fingers out of “pinch point” areas; clearances between the doors and cabinet are necessarily small. Be careful when you open the doors when children are in the area. - • • • • - • Do not disassemble or repair the refrigerator by yourself. You run a risk of causing a fire, malfunction and / or personal injury. In case of malfunction, please contact your service agent. • If the appliance generates a strange noise, a burning or smell or smoke, unplug the power plug immediately and contact your nearest service center. Failing to do so may result in an electric or fire hazards. If you experience difficulty when changing the light, contact service agent. If the products is equipped with the LED Lamp, do not disassemble the Lamp Cover and LED Lamp by yourself. Please contact your service agent. If any dust or water is in the refrigerator, pull out power plug and contact your Samsung Electronics service center. There is a risk of fire. If any foreign substance such as water has entered the appliance, unplug the power plug and contact your nearest service center. Failing to do so may result in an electric shock or fire. CAUTION - - CAUTION SIGNS FOR USING • To get best performance from the product, Do not place foods too closely in front of the vents at the rear of the appliance as it can obstruct free air circulation in the refrigerator compartment. Wrap the food up properly or place it in airtight containers before putting it into the refrigerator. Safety information _05 • - • - • - • • • • • • - • - Do not put any newly introduced food for freezing near to already existing food. Do not place carbonated or fizzy drinks in the freezer compartment. Do not put bottles or glass containers in the freezer. When the contents freeze, the glass may break and cause personal injury and property damage. Do not change or modify the functionality of the refrigerator. Changes or modifications may result in a personal injury and/or property damage. Any changes or modifications performed by a 3rd party on this completed appliance are neither covered under Samsung warranty service, nor is Samsung responsible for safety issues and damages that result from 3rd party modifications. Do not block air holes. If the air holes are blocked, especially with a plastic bag, the refrigerator can be over cooled. If this cooling period lasts too long, the water filter may break and cause water leakage. Please observe maximum storage times and expiry dates of frozen goods. Fill the water tank, ice tray, water cubes only with potable water. Use only the ice-maker provided with the refrigerator. The water supply to this refrigerator must only be installed/connected by a suitably qualified person and connected to a potable water supply only. In order to operate the ice-maker properly, water pressure of 138 ~ 862 kPa is required. Do not spray volatile material such as insecticide onto the surface of the appliance. As well as being harmful to humans, it may also result in an electric shock, fire or problems with the product. Do not use a hair dryer to dry the inside of the refrigerator. Do not place a lighted candle in the refrigerator for removing bad others. This may result in an electric shock or fire. 06_ Safety information CAUTION CAUTION SIGNS FOR CLEANING AND MAINTENANCE • Do not directly spray water inside or outside the refrigerator. - There is a risk of fire or electric shock. • Do not use or place any substances sensitive to temperature such as inflammable sprays, inflammable objects, dry ice, medicine, or chemicals near the refrigerator. Do not keep volatile or inflammable objects or substances (benzene, thinner, propane gas, etc.) in the refrigerator. - This refrigerator is for storing food only. - This may result in a fire or an explosion. • Do not spray cleaning products directly on the display. - Printed letters on the display may come off. • Remove any foreign matter or dust from the power plug pins. But do not use a wet or damp cloth when cleaning the plug, remove any foreign material or dust from the power plug pins. - Otherwise there is a risk of fire or electric shock. • Unplug the refrigerator before cleaning and performing maintenance. WARNING SEVERE WARNING SIGNS FOR DISPOSAL • Ensure that none of the pipes on the back of the appliance are damaged prior to disposal. • R600a or R134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the refrigerator to see which refrigerant is used for your refrigerator. When this product contains flammable gas (Refrigerant R600a), contact your local authority in regard to safe disposal of this product. Cyclopentane is used as an insulation blowing gas. The gases in insulation material require special disposal procedure. Please contact your local authorities in regard to the environmentally safe disposal of this product. Ensure that none of the pipes on the back of the appliances are damaged prior to disposal. The pipes shall be broken in the open space. • When disposing of this product or other refrigerators, remove the door/door seals, door latch so that small children or animals cannot become trapped inside. • Leave the shelves in place so that children may not easily climb inside. Ensure that none of the pipes on the back of the appliance are damaged prior to disposal. R600a or R134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the fridge to see which refrigerant is used for your refrigerator. When this product contains flammable gas (Refrigerant R600a) contact your local authority in regard to safe disposal of this product. • Cyclopentane used as an insulation blowing gas. The gases in insulation material require special disposal procedure. Please contact your local authorities in regard to the environmentally safe disposal of this product. Ensure that none of the pipes on the back of the appliances are damaged prior to disposal. The pipes shall be broken in the open space. • Please dispose of the packaging material for this product in an environmentally friendly manner. • Allow the appliance to stand for 2 hours after installation. • To get Best performance from the product, - Do not place foods too closely in front of the vents at the rear of the appliance as it can obstruct free air circulation in the freezer compartment. - Wrap the food up properly or place it in airtight containers before putting it into the fridge or freezer. - Do not put any newly introduced food for freezing near to already existing food. • Do not place glass or bottles or carbonated beverages into the freezer. - The container may freeze and break, and this may result in injury. • Please observe maximum storage times and expiry dates of frozen goods. • There is no need to disconnect the refrigerator from the power supply if you will be away for less than three weeks. But, Remove all the food if you are going away for the three weeks or more. • Unplug the refrigerator and clean it, rinse and dry. • Remove all foreign substances such as dust • • • • • - or water from the power plug terminals and contact points using a dry cloth on a regular basis. Unplug the power plug and clean it with a dry cloth. Failing to do so may result in an electric shock or fire. Before cleaning or performing maintenance, unplug the appliance from the wall socket. Failing to do so may result in an electric shock or fire. Do not clean the appliance by spraying water directly onto it. Do not use benzene, thinner or alcohol to clean the appliance. This may result in discoloration, deformation, damage, electric shock or fire. Do not spray inflammable gas near the refrigerator. There is a risk of explosion or fire. Contains fluorinated greenhouse gases covered by the Kyoto Protocol. Hermetically sealed system. Do not vent gases into the atmosphere. Refrigerant type : R-134a Quantity: 0.16 kg Global Warming Potential (GWP) = 1300 ADDITIONAL TIPS FOR PROPER USAGE • In the event of a power failure, call the local office of your Electricity Company and ask how long it is going to last. - Most power failures that are corrected within an hour or two will not affect your refrigerator temperatures. However, you should minimize the number of door openings while the power is off. - Should the power failure last more than 24 hours, remove all frozen food. • If keys are provided with the refrigerator, the keys should be kept out of the reach of children and not be in the vicinity of the appliance. • The appliance might not operate consistently (possibility of temperature becoming too warm in the refrigerator) when sited for an extended period of time below the cold end of the range of temperature for which the refrigerating appliance is designed. • Do not store food which spoils easily at low Safety information _07 temperature, such as bananas, melons. • Your appliance is frost free, which means there is no need to manually defrost your appliance, as this will be carried out automatically. • Temperature rise during defrosting can comply with ISO requirements. But if you want to prevent an undue rise in the temperature of the frozen food while defrosting the appliance, please wrap the frozen food up in several layers of newspaper. • Any increase in temperature of frozen food during defrosting can shorten its storage life. Saving Energy Tips - - - - - - Install the appliance in a cool, dry room with adequate ventilation. Ensure that it is not exposed to direct sunlight and never put it near a direct source of heat (radiator, for example). Never block any vents or grilles on the appliance. Allow warm food to cool down before placing it in the appliance. Put frozen food in the refrigerator to thaw. You can then use the low temperatures of the frozen products to cool food in the refrigerator. Do not keep the door of the appliance open for too long when putting food in or taking food out. The shorter time for which the door is open, the less ice will form in the freezer. Clean the rear of the refrigerator regularly. Dust increases energy consumption. Do not set temperature colder than necessary. Ensure sufficient air exhaust at the refrigerator base and at the back wall of the refrigerator. Do not cover air vent openings. Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower. To get the best energy efficiency of this product, please leave all selves, drawers and baskets on their original position like as above illustration. Contents SETTING UP YOUR FRENCH DOOR REFRIGERATOR ………………………………… 09 OPERATING YOUR FRENCH DOOR REFRIGERATOR …………………………………… 15 TROUBLESHOOTING ………………………………………………………………………… 24 08_ Safety information Setting up your French Door Refrigerator Congratulations on your purchase of this Samsung French Door Refrigerator. We hope you enjoy the state-of-art features and efficiencies that this new appliance offers. Selecting the best location for the refrigerator • • • • A location with easy access to a water supply. A location without direct exposure to sunlight. A location with a leveled floor. A location with enough space for the refrigerator doors to open easily. • A location that allows sufficient space to the right, left, back and top for air circulation. • A location that allows you to move the refrigerator easily if it needs maintenance or service. 5 cm • Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower. • Do not install the refrigerator where the temperature will go below 10 ºC. • Do not locate the refrigerator where it may become wet. When moving your refrigerator CAUTION To prevent floor damage, be sure the front adjusting legs are in the up position (above the floor). Refer to ‘Adjusting the Level’ in the manual (on page 12). FLOORING For proper installation, you must place this refrigerator on a level, hard surface that is the same height as the rest of the floor. This surface should be strong enough to support a fully loaded refrigerator, or approximately 150 kg. To protect the finish of the flooring, cut a large section of the cardboard carton and place it under the refrigerator where you are working. When moving the refrigerator, you need to pull and push it straight forwards or back. Do not wiggle it from side to side. 10 cm 5 cm setting up _09 01 SETTING UP GETTING READY TO INSTALL THE REFRIGERATOR REMOVING THE REFRIGERATOR DOORS For some installations you need to remove the fridge and freezer drawers so you can move the refrigerator to its final location. Do not remove the doors/drawer if you don’t need to. If you do not need to remove the refrigerator doors, go to Adjusting the Level on page 12. If you need to remove the doors. continue below. Before removing the door/drawer, make sure you read the following items: Disassemble the refrigerator doors WARNING Be careful not to drop and scratch the doors while removing the doors. With the door opened 1. Remove 3 screws holding down the TOP TABLE ( 1 ) and turn it with wires connected. 1 Required Tools (Not provided) You need the following tools to complete the installation of your refrigerator: Philips screwdriver(+) Flat-blade screw driver(-) Socket wrench (10 mm) 2. Disconnect two connector ( 2 ) on the left side door. To remove the water coupler from the hinge, twist and pull it from the hinge. 2 Pliers WARNING Allen wrench (5 mm) Disconnect power to the refrigerator before removing the door or drawer. • Be careful not to drop, damage or scratch the door/drawer while removing them. • Be careful not to get injured while removing the door/drawer. • Reattach the door/drawer properly to avoid: - Moisture from air leakage. - Uneven door alignment. - Wasting energy due to improper door seal. 3. Pull and remove the hinge lever ( 3 ). Remove the ground screw ( 4 ) attached to the upper left door hinges with a philips screwdriver (+). Remove the upper left and right door hinges ( 5 ). 3 4 5 4. Lift the door straight up to remove. 10_ setting up 5. Remove the screw ( 6 ) attached to the lower left and right door hinges with a philips screwdriver (+). Remove the 2 hex head bolts ( 7 ) attached to the lower left and right door hinges with an allen wrench 5 mm. Remove the lower left and right door hinges ( 8 ). 8 7 CAUTION Make sure there is no scratch at the end of Sliding Rail by being dented from the floor. Make sure that you mount the freezer basket in the right position when removing / installing the freezer door. Failing to do so may result in the door not opening or closing properly. Do not overload the bottom basket or the top drawer. Overloading prevents the Freezer drawer from closing properly and will eventually cause frost build-up. Allen wrench DISASSEMBLE THE FLEX DOOR 1. Take out the upper drawer by lifting it up. 2. Take out the lower basket ( 1 ) by lifting the basket up from the rail system. 1 3. Press the fixing hook of rail system. ASSEMBLE THE FREEZER DRAWER To reattach the drawer after you have moved the fridge to its final location, assemble parts in reverse order. 4. After holding and pulling out the top of Freezer Door, remove it at the rail system. setting up _11 01 SETTING UP 6 CAUTION ADJUSTING THE LEVEL Make sure the refrigerator is level so that you can make final adjustments. Use a level to test if the refrigerator is level both side to side and back to front. If the refrigerator is not level, it will not be possible to get the doors perfectly even, which may cause moisture condensation and increased energy bills. Below is an example of how to level the refrigerator if the left side of the refrigerator is lower than the right side. Fixed part Adjustment part The left door is fixed. To make minor adjustments between doors, adjust only the right door. How to adjust the level 1. Open the freezer drawer and remove the lower basket. 2. Insert a flat-blade screwdriver (-) into a notch on the left control lever, and turn it count clockwise to level the refrigerator. (You turn the lever clockwise to lower the refrigerator and counterclockwise to raise it.) 2 3 3 4 1 flat-blade screwdriver(-) Control Lever CAUTION Both control levers must be touching the floor to avoid possible personal injury or property damage because of tipping. If the right side is lower, perform the same procedure, but with the right control lever. It is difficult to remove the cover leg front from the refrigerator, so we do not recommend making small adjustments with the control lever. Instead, refer to the next page for the best way to make minor adjustments to the doors. MAKING MINOR ADJUSTMENTS BETWEEN DOORS Remember, a leveled refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on leveling the refrigerator. 12_ setting up 1. Pull out the freezer drawer ( 1 ), then you can see the lower hinge ( 2 ). 2. Insert the supplied allen wrench 5 mm ( 3 ) into the shaft ( 4 ) of the lower hinge. 3. Please adjust the height by turning the hex wrench ( 3 ) clockwise ( DOWN ) or counterclockwise ( UP ). When you turn the hex wrench counterclockwise ( ), the door will move up. 4. After adjusting the doors, insert the supplied fastener ( 6 ) using a pliers ( 5 ) in the gap between the hinge-grommet ( 7 ) and the lower hinge ( 8 ). The number of fasteners you’ll need to insert depends on the gap. 2 fastener are enclosed with the refrigerator. The thickness of each fastener is 1 mm. INSTALLING THE WATER DISPENSER LINE Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and 6 mm compression nut. 2. Locate the nearest cold water drinking line and install the pipe clamp and shut off valve. Cold water line Pipe clamp Shut off valve 3. Connect the water line installation kit to the shut off valve. Cold water line Water line installation kit Pipe clamp Shut off valve Connecting the water supply line to the refrigerator. There are several items that you need to purchase to complete this connection. You may find these items sold as a kit at your local hardware store. Use Copper Tubing • 6 mm copper tubing • 6 mm compression nut (1pc) • Ferrule (2pc) Use Plastic Tubing • 6 mm plastic tubing → Molded end(Bulb) • 6 mm compression nut (1pc) setting up _13 01 SETTING UP A water dispenser with a filter is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. In order for the ice maker to operate properly, a water pressure of 138 ~ 862 kPa is required. Under normal conditions, a 0.17 L cup can be filled in about 10 seconds. If the refrigerator is installed in an area with low water pressure (below 138 kPa), you can install a booster pump to compensate for the low pressure. After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Connecting to the water supply line 1. First, shut off the main water supply. COMPLETING THE SET UP Refrigerator Compression nut (6.35 mm) (Supplied) Plastic tubing (Supplied) Compression fitting (Supplied) Bulb Ferrule (Not supplied) Compression nut (6.35 mm) (Not supplied) Copper tubing or Plastic tubing (Not supplied) (Not supplied) Household water line 1. Slip the compression nut through the supplied plastic tubing . 2. Tighten the compression nut onto the 6.35 mm compression fitting. - If you are using copper tubing, slip the compression nut (not included) and ferrule (not included) on copper tubing (not included) as shown. - If you are using plastic tubing , insert the molded end(Bulb) of the plastic tubing into the compression fitting. Do not use without the molded end(Bulb) of the plastic tubing . 3. Tighten the compression nut onto the compression fitting. Do not over-tighten the compression nut . 4. Turn water on and check for any leakage. Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6 mm of the plastic tubing to make sure you get a snug, leak-free connection. CAUTION 14_ setting up Now that you have your new refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance. By completing the following steps, your refrigerator should be fully operational. 1. Make sure your refrigerator is in an appropriate location with reasonable clearance between it and the wall. Refer to installation instructions in this manual. 2. Once the refrigerator is plugged in, make sure the interior light comes on when you open the doors. 3. Set the Temperature control to the coldest temperature and wait for an hour. The freezer will get slightly chilled and the motor will run smoothly. Reset the refrigerator and freezer to the temperatures you want. 4. After you plug the refrigerator in, it will take a few hours to reach the appropriate temperature. You can store food and drinks in the refrigerator after the temperature is sufficiently cool. To get more space , you can remove top freezer drawers since it does not affect thermal and mechanical characteristics. A declared storage volume of frozen food storage compartment is calculated with these drawers removed. Operating your French Door Refrigerator USING THE CONTROL PANEL 02 OPERATING Water Pure Touch One 1 2 3 ( 1 ) Ice Off Button Press the Ice off button if you want to turn the ice-maker off. ( 2 ) Power Freeze Button Speeds up the time needed to freeze products in the Freezer. It can be helpful if you need to quickly freeze easily spoiled items or if the temperature in the Freezer has warmed dramatically (for example, if the door was left open). When you use this function the energy consumption of the refrigerator will increase. Remember to turn it off when you don’t need it and return the freezer to your original temperature setting. • Power freezing - If you need to freeze large amount of food stuff, activate Power Freeze function at least 24 hours before. (3) Freezer Button Press the Freezer button to set the Freezer to your desired temperature. You can set the temperature between -15 °C and -23 °C. ( 4 ) Fridge Button Press the Fridge button to set the fridge to your desired temperature. You can set temperature between 1 °C and 7 °C. ( 5 ) Power Cool Button Speeds up the time needed to cool products in the Refrigerator. It can be helpful if you need to quickly cool easily spoiled items or if the temperature in the fridge has warmed dramatically (For example, if the door was left open). 7 4 5 6 ( 6 ) E. Saver Button For better energy efficiency, press E.Saver button. However, if condensation occurs on the door, turn the E.Sasver function off. Press this button for 3 seconds to switch the temperature units between °C and °F. ( 7 ) Filter Indicator When the filter indicator light is on, it is time to change the filter. Typically this happens about every 6 months. The filter Indicator will be Off when you initially insert the water filter. The filter Indicator will be Off when you have used your water filter for 5 months. The filter Indicator will be Red when you have used your water filter for 6 months. operating _15 CHANGING THE WATER FILTER To reduce risk of water damage to your property DO NOT use generic brands of water filters in your SAMSUNG Refrigerator. USE ONLY SAMSUNG BRAND WATER FILTER. SAMSUNG will not be legally responsible for any damage, including, but not limited to property damage caused by water leakage from use of a generic water filter. SAMSUNG Refrigerators are designed to work ONLY WITH SAMSUNG Water Filter. The Filter light turns red to let you know when it is time to change your water filter cartridge. To give you time to get a new filter, the red light comes on just before the (Red) capacity of the current filter runs out. Changing the filter on time provides you with the freshest, cleanest water from your refrigerator. 4 WARNING 5. After removing the old water filter and installing a new reset the indicator by pressing the “Fridge” and “Power Cool” button simultaneously for about 3 seconds. 6. If you turned off the water supply, turn it back on. 1. Shut off the water supply. Then, turn the water filter ( 1 ) about 1/4 turn, counter-clockwise. 2. Pull the water filter ( 1 ) from the case filter ( 2 ). 2 1 • • • 3. 4. • To change the water filter more easily, shut off the water supply valve. Sometimes, it is hard to disassemble the water filter because impurities in the water cause it to stick. If you are having difficulties, grip the water filter firmly and pull it hard. When you pull the water filter, a little 2 water can leak from 3 the opening. This is normal. To minimize the water leaks, keep the filter cartridge horizontal when you pull it. To prevent overflow, empty the water filter tray ( 3 ) and dry around the filter case ( 2 ). Insert the new filter into the filter case ( 4 ). Push the filter, and then turn it clockwise until it locks. • If you have trouble inserting the water filter because of high water pressure, shut off the water supply valve. • The locked symbol should be lined up with the indicator line. 16_ operating For a replacement water filter, you can visit your local home Improvement center or contact the Samsung Parts distributor. Be sure the replacement water filter has the SAMSUNG logo on the box and on the water filter. Link : http://www. samsungparts.com Removing any residual matter inside the water supply line after installing the water filter. 1. Turn ON the main water supply and supply water from water supply line. 2. Run water through the dispenser until the water runs clear (approx. 6 to 7 minutes). This will clean the water supply system and remove air from the lines. 3. Additional flushing may be required in some households. 4. Open the Refrigerator door and make sure there are no water leaks coming from the water filter. Be sure to flush the dispenser thoroughly, otherwise water may drip from the dispenser. This means that there is still air in the line. CONTROLLING THE TEMPERATURE The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 241 and 827 kPa. If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 276 to 414 kPa. If the water pressure to the reverse osmosis system is less than 276 to 414 kPa : Controlling the Freezer temperature • Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary. • Allow the storage tank on the reverse osmosis system to refill after heavy usage. • If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. If you have questions about your water pressure, call a licensed, qualified plumber. CONTROLLING THE TEMPERATURE Basic temperature of Freezer and Refrigerator Compartments The basic temperature and recommended temperatures of the Freezer and Refrigerator Compartments are -18 °C and 3 °C respectively. If the temperature of the Freezer and Refrigerator Compartments are too high or low, adjust the temperature manually. The Freezer temperature can be set between -15 °C and -23 °C to suit your particular needs. Press the Freezer button repeatedly until the desired temperature is shown in the temperature display. Keep in mind that foods like ice cream may melt at -15 °C. The temperature display will move sequentially from -23 °C to -15 °C. When the display reaches -15 °C, it will begin again at -23 °C. Five seconds after the new temperature is set, the display will again show the actual current freezer temperature until the new temperature is reached. Controlling the Refrigerator temperature The Refrigerator temperature can be set between 7 °C and 1 °C to suit your particular needs. Press the Fridge button repeatedly until the desired temperature is shown in the temperature display. The temperature control process for the Fridge works just like the Freezer process. Press the Fridge button to set your desired temperature. After a few seconds, the Fridge will begin adjusting towards the newly set temperature. This will be reflected in the digital display. The temperature of the Freezer or the Refrigerator may rise from opening the doors too frequently, or if a large amount of warm or hot food is placed in either side. This may cause the digital display to blink. Once the Freezer and Refrigerator temperature return to their normal set temperatures, the blinking will stop. If the blinking continues, you may need to “reset” the Refrigerator. Try unplugging the appliance, wait for around 10 minutes and then plug the power cord back in. operating _17 02 OPERATING Reverse Osmosis Water Supply IMPORTANT: USING THE COLD WATER DISPENSER Using the Water dispenser (RF261B) Place a glass underneath the water outlet and push gently against the water dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the water from splashing out. R 0URE7ATE /NE4OUCH PUSH If you have just installed the refrigerator or installed a new water filter, Flush 11 L through filter before use (flush approximately 6 minutes). Make sure water flows cleanly before drinking. CAUTION If you have a long vacation or business trip, close the water valve and shut off the water supply to the Refrigerator. This will help prevent accidental leakages. Water clouding phenomenon All water provided to refrigerators flows through the core filter which is an alkaline water filter. In this process, the pressure in the water that has flowed out of the filter gets increased, and oxygen and nitrogen become saturated. When this water flows out in the air, the pressure plummets and the oxygen and nitrogen get supersaturated so that they turn into gas bubbles. The water could look misty due to these oxygen bubbles.The water may look temporarily cloudy due to these oxygen bubbles. After a few seconds, the water will look clear. The water tank’s capacity is approximately 1 L. Please wait 1 second before removing the cup after dispensing water to prevent spills. 18_ operating PARTS AND FEATURES Use this page to become more familiar with the parts and features of the refrigerator Light Slide-Shelf Internal Water Dispenser(RF261B) e ter Wa Quick-Space Glass Shelf (on some models) Pur ch Tou One Door Bins Vegetable & Fruit Drawers Cool Select Pantry PLUS Light FZ Ice-Maker Ice Bucket Auto Pull Out Drawer Freezer Drawer Bin When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid scratching the other door. If the Vertical Hinged Section is reversed, put it back to the right position and close the door. Moisture may appear at times on the Vertical Hinged Section. The door handle may become loose over time. If this happens, tighten the bolts found on the inside of the door. If you close one door with a lot of force, the other door may open. When the door opens, the interlock switch automatically turns off the auger motor in the ice maker for safety reasons. When the interior or exterior LED lamp has gone out, please contact your service agents. operating _19 02 OPERATING Vertical Hinged Section USING THE COOL SELECT PANTRY™ The Cool Select Pantry™ is a full-width drawer with adjustable temperature control. This pantry can be used for large party trays, deli items, pizza, beverages or miscellaneous items. There is a temperature control which can adjust the amount of cold air allowed into the pantry. The control is located on the right side of the pantry. • The Pantry has three modes: The Fresh mode, Zero Zone mode, and Deli mode. Fresh mode is the default. Press the Temp button repeatedly until the mode you want is lit. Once you select a mode, the temperature will change to match the mode you selected. • The Pantry temperature may change depending on the number of items inside and where they are located, the ambient temperature, and how often the door is opened. Deli • Pineapple • lemon • avocado • potato Fresh • cucumbers • apples • oranges • grapes • zucchinis • corn Fruits and vegetables may be damaged when the “Zero Zone” mode is set. Do not store lettuce or other leafy produce in this pantry. CAUTION Do not store glass bottles in this pantry. If they are frozen, they can break and cause personal injury. CAUTION In case you put a water bowl without its lid into the pantry, condensation may form around surrounding parts. REMOVING THE REFRIGERATOR ACCESSORIES 1. Door Bins & Dairy Compartment • Door Bins To remove - Simply lift the bin up and pull straight out. To relocate - Slide it in above the desires location and push down until it stops. The Pantry Selection Button 1. When you select “Deli”, the temperature of the pantry will be kept around 5 °C. This feature helps keep food fresh for a long time. 2. When you select “Fresh”, the temperature of the pantry will be kept around 3 °C. This feature helps keep food fresh for a longer time. 3. When you select “Zero Zone”, the temperature of the pantry will be kept around 0 °C. This feature also helps keep meat or fish fresh for a longer time. The table below lists the Pantry modes and the kinds of foods that can be stored safely for each mode. 20_ operating Zero Zone • steaks • hard cheeses • cold cuts • bacon • hot dogs er e Pur ch Tou One Wat Injury may occur if the door bins are not firmly assembled. Do not allow children to play with bins. Sharp corners of the bins may cause injury. Do not adjust a bin full of food. Remove the food first. Dust removal method - Remove the guard and wash in water. CAUTION To remove - Tilt up the front of the shelf in the direction shown ( 1 ) and lift it up vertically ( 2 ). Pull the shelf out. To relocate - Tilt the front of the shelf up and guide the shelf hooks into the slots at a desired height. Then lower the front of the shelf so that the hooks can drop into the slots. CAUTION The Tempered Glass shelves are heavy. Use special care when removing them. Using the doors 1 2 Ensure that the doors close all the way and are securely sealed. When the refrigerator door is only partially open, it will automatically close. But, the door will stay open when opened more than the auto close range and you must close it manually. 3. Vegetable & Fruit Drawers To remove - Pull the drawer out to full extension. Tilt up the front of the drawer and pull straight out. To relocate - Insert the drawer into the frame rails and push back into place. CAUTION The drawers need to be removed before the glass shelf above them can be lifted out. REMOVING THE REFRIGERATOR ACCESSORIES 1. ICE BUCKET To remove - Lift the ice bucket ( 1 ). To relocate - Place the ice bucket into the Super extended drawer ( 2 ). 1 2 4. Cool select pantry To remove the Cool select pantry – Pull the pantry out to full extension. Tilt up the front side of the pantry and pull straight out. operating _21 02 OPERATING 2. Tempered Glass shelves To relocate the Cool select pantry – Push the rails to the back of the refrigerator. Place the drawer onto the rails and slide the pantry back until it is in place. To remove the divider – Pull the pantry completely out to full extension and raise the front side of the divider to unhook it from the rear wall of the pantry, then lift the divider out. To relocate the divider - Hook the back of the divider over the rear wall of the pantry and push the divider down. 2. Super Extended Drawer To remove - Pull the drawer out to full extension. Tilt up the rear of the drawer and lift straight out. To relocate - Place the drawer onto the rails ( 4 ) by tilting it up. Lower the drawer into place until it is horizontal and slide the Drawer ( 3 ) in. CLEANING THE REFRIGERATOR Caring for your Samsung French Door Refrigerator prolongs the life of your appliance and helps keep the refrigerator free of odor and germs. Cleaning the Interior 4 3 Clean the inside walls and accessories with a mild detergent and then wipe dry with a soft cloth. You can remove the drawers and shelves for a more thorough cleaning. Just make sure to dry drawers and shelves before putting them back into place. 3. Freezer Drawer To remove the freezer drawer - Pull the freezer drawer out fully. Tilt up the rear of the bin and lift it out to remove. To relocate the freezer drawer - Place the bin into the rail assembly. CAUTION CAUTION WARNING Do not allow babies or children go inside the freezer drawer. They could damage the refrigerator and seriously injure themselves. Do not sit on the freezer door. The door may break. Do not allow children to climb into the freezer drawer. Do not remove the divider. Cleaning the Exterior Wipe the control panel and digital display with a damp, clean, soft cloth. Do not spray water directly on the surface of the refrigerator. The doors, handles and cabinet surfaces should be cleaned with a mild detergent and then wiped dry with a soft cloth. To keep your appliance looking its best, polish the exterior once or twice a year. If trapped inside, children may be injured or suffocate to death. CAUTION Do not spray water directly on the refrigerator. Use a clean, damp cloth to clean. CAUTION Do not use benzene, thinner, or Clorox for cleaning. They may damage the surface of the appliance and may cause a fire. CAUTION 22_ operating You can erase the printed letters on the display if you apply stainless cleaner directly to the area where the letters are printed. If the rubber door seals are dirty, the doors may not close properly, and the refrigerator will not operate efficiently. Keep the door seals free of dust or stains by cleaning the doors with a mild detergent and damp cloth. Wipe dry with a clean, soft cloth. 02 OPERATING CAUTION Do not clean the refrigerator with benzene, thinner, or car detergent due to risk of fire. Cleaning the rear side of the refrigerator To keep cords and exposed parts free of dust and dirt accumulation. Vacuum the rear side of the appliance once or twice a year. CAUTION Do not remove the back cover ( 1 ). You could suffer an electric shock. 1 operating _23 Troubleshooting PROBLEM The refrigerator does not work at all or it does not chill sufficiently. SOLUTION • Check that the power plug is properly connected. • Check if the set temperature on the digital display is warmer than the freezer or fridge inner temperature. If it is, set the refrigerator colder. • Is the refrigerator in direct sunlight or located near a heat source? • Is the back of the refrigerator too close to the wall, preventing proper ventilation? The food in the fridge is frozen. • • • • You hear unusual noise or sounds. • Check that the refrigerator is level and stable. • Is the back of the refrigerator too close to the wall, preventing proper ventilation? Try moving the back of the refrigerator at least 50 mm from the wall. • Was anything dropped behind or under the refrigerator? • A “ticking” sound is heard from inside the refrigerator. It is normal and occurs because various accessories are contracting or expanding according to the temperature of the refrigerator interior. • If it sounds as if something is hitting something else inside the refrigerator, this is normal. The sound is caused by the compressor operating at high capacity. The cabinet-door sealing area of the appliance is hot and condensation is occurring. Ice Maker is not producing ice. Check if the set temperature on the digital display is too low. Try setting the refrigerator to a warmer temperature. Is the temperature in the room too low? Set the refrigerator warmer. Did you store the food which is juicy in the coldest part of the refrigerator? Try moving those items to the other shelves in the fridge instead of keeping them in the colder areas or bins. • Some heat is normal as anti-condensators are installed in the vertical hinged section of the refrigerator to prevent condensation. • Is the refrigerator door ajar? Condensation can occur when you leave the door open for a long time. • • • • Did you wait for 12 hours after installation of the water supply line before making ice? Is the water line connected and the shut-off valve opened? Did you manually stop the ice making function? Is the freezer temperature too warm? Try setting the freezer temperature lower. You can hear water bubbling in the refrigerator. • This is normal. The bubbling comes from refrigerant circulating through the refrigerator. There is a bad smell in the refrigerator. • Check for spoiled food. • Foods with strong odors (for example, fish) should be tightly covered. • Clean out your freezer periodically and throw away any spoiled or suspicious food. Frost forms on the walls of the freezer. • Is the air vent blocked? Remove any obstructions so air can circulate freely. • Allow sufficient space between the stored foods for efficient air circulation. • Is the freezer drawer closed properly? Water dispenser is not functioning. • • • • Auto close system does not work with the freezer door. • Is there an imbalance between the right and left parts of the door? • Open and close the door smoothly 1~2 times. After you do this, the auto close system usually works properly again. • Try opening the door smoothly to avoid unbalancing the right part and the left part of the door. 24_ Troubleshooting Is the water line connected and the shut-off valve opened? Has the water supply line tubing been crushed or kinked? Make sure the tubing is free and clear of any obstruction. Is the water tank frozen because the fridge temperature is too low? Try selecting a warmer setting on the Digital display. Memo Memo Memo Ambient Room Temperature Limits This fridge/freezer is designed to operate in ambient temperatures specified by its temperature class marked on the rating plate. Class Symbol Ambient Temperature range(°C) Extended Temperate SN +10 to +32 Temperate N +16 to +32 Subtropical ST +16 to +38 Tropical T +16 to +43 Internal temperatures may be affected by such factors as the location of the fridge/freezer, ambient temperature and the frequency with which you open the door. Adjust the temperature as required to compensate for these factors. www.samsung.com/register Напольное устройство ПРЕДУПРЕЖДЕНИЕ СИМВОЛЫ, ПРЕДУПРЕЖДАЮЩИЕ О СЕРЬЕЗНОЙ ОПАСНОСТИ ПРИ ТРАНСПОРТИРОВКЕ И УСТАНОВКЕ - - ПРЕДУПРЕЖДЕНИЕ - • • - • • • • • • - • • • - • • • • • - • • • • - • • • • • • - - • • • СИМВОЛЫ ПРЕДОСТЕРЕЖЕНИЯ ДЛЯ УСТАНОВКИ • • ПРЕДУПРЕЖДЕНИЕ - - • • • • • • • • • - - СИМВОЛЫ ПРЕДОСТЕРЕЖЕНИЯ ДЛЯ ИСПОЛЬЗОВАНИЯ - • • - • - • • • • • • - • - ОСТОРОЖНО ПРЕДОСТЕРЕГАЮЩИЕ ЗНАКИ ДЛЯ УБОРКИ ПРЕДУПРЕЖДАЮЩИЕ ЗНАКИ ДЛЯ УТИЛИЗАЦИИ • • • • • • - - • • • - - - - - - - 5 cm 10 cm 5 cm 01 НАСТРОЙКА УДАЛЕНИЕ ДВЕРЕЦ ХОЛОДИЛЬНИКА ПРЕДУПРЕЖДЕНИЕ 1 ПРЕДУПРЕЖДЕНИЕ 4 5 ОСТОРОЖНО 1 01 НАСТРОЙКА 6 ОСТОРОЖНО ОСТОРОЖНО 2 3 3 4 1 УСТАНОВКА ТРУБОПРОВОДА 01 НАСТРОЙКА ЗАВЕРШЕНИЕ НАСТРОЙКИ Трубопровод дома Water Pure Touch One 1 2 3 от -15 °C до -23 °C. 7 4 5 6 (6) Кнопка E. Saver Работа _15 4 2 1 • • • 3. 4. 16_ Работа 02 РАБОТА УПРАВЛЕНИЕ ТЕМПЕРАТУРОЙ TER H0URE7A /NE4OUC НАЖМИТЕ 18_ Работа e Pur ch Tou One ter Wa Овощи и Фрукты Cool Select PantryPLUS Работа _19 02 РАБОТА • авокадо • виноград • тыква • кукуруза ОСТОРОЖНО ОСТОРОЖНО er e Pur ch Tou One Wat ОСТОРОЖНО 1 1 2 Работа _21 02 РАБОТА 4 3 ОСТОРОЖНО ПРЕДУПРЕЖДЕНИЕ ОСТОРОЖНО ОСТОРОЖНО ОСТОРОЖНО 22_ Работа 02 РАБОТА ОСТОРОЖНО ОСТОРОЖНО Работа _23 СПОСОБ УСТРАНЕНИЯ • • • • • • • • Заметки Обозначение SN от +10 до +32 N от +16 до +32 ST от +16 до +38 T от +16 до +43 . . . . • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 22 21 4 3 20 1 19 • • • • • • • • • • • • • • • • • 18 er Wat e Pur ch Tou One e Pur ch Tou One 17 TER H0URE7A /NE4OUC 16 15 2 .1 1 .2 • 14 • • .3 .4 Water Pure Touch One 6 5 4 7 3 2 1 13 .2 .3 .4 .1 .2 - .3 .4 12 11 2 3 3 4 1 10 6 7 09 צבת • • - 2 3 5 08 • • • 07 • • • • • • - - 06 • • • - • • • • • • • • • • • • • • • • • - 05 • • • • • • • • • • • • • • • • • • - 04 • - • • • • • - • • - - • - • • • • • • • - - • • • • • • • • • • • • • • • • • • • - • • - • • • • • • • - • • • • 03 • • • • • • • - - - • • 02 • RF260B DA68-02616B-01
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project